Is there any way to root the Samsung Galaxy S3 Neo i9301i with Android 4.4.2 KitKat on it?
Hope somebody can help me :fingers-crossed:
ViktorFoedowski said:
Is there any way to root the Samsung Galaxy S3 Neo i9301i with Android 4.4.2 KitKat on it?
Hope somebody can help me :fingers-crossed:
Click to expand...
Click to collapse
Still no answers?
I'd also like to root this device.
Maybe with towelroot?
+1 for supporting rooting s3 neo
Thx
Towelroot works brother
Sent from my GT-I9300I using Tapatalk
ViktorFoedowski said:
Is there any way to root the Samsung Galaxy S3 Neo i9301i with Android 4.4.2 KitKat on it?
Hope somebody can help me :fingers-crossed:
Click to expand...
Click to collapse
+1
---------- Post added at 10:21 AM ---------- Previous post was at 10:19 AM ----------
mianahmadpp said:
Towelroot works brother
Sent from my GT-I9300I using Tapatalk
Click to expand...
Click to collapse
no for me, popup advise that device not supported
---------- Post added at 10:25 AM ---------- Previous post was at 10:21 AM ----------
vroot no work, until now
Sent from my GT-I9301I
---------- Post added at 10:36 AM ---------- Previous post was at 10:25 AM ----------
framaroot no work
Sent from my GT-I9301I
---------- Post added at 10:46 AM ---------- Previous post was at 10:36 AM ----------
POOT no work
Sent from my GT-I9301I
rod555 said:
no for me, popup advise that device not supported
Click to expand...
Click to collapse
you propably updated to the new version of Kitkat 4.4.2.
The new update had the bandversion I9301IXXUANF4 for me (I updated too) (there is no possible way to root this version as far as i know)
But the not updated version of KitKat 4.4.2 (bandversion for me: I9301IXXUANC6) works with towelroot.
Beside i updated to the new update i still got my phone rooted:
I downloaded the new version of Odin on my pc.
I downloaded the old version from sammobile. (the I9301IXXUANC6 version)
In Odin (launched with admin rights) you click on the PDA (or sometimes AP called) button and select the downloaded firmware version (unpacked)
Next boot your phone in recovery mode (turn it off, then press volume down + home + power button)
Connect your phone to your pc (after that odin should recognize your phone)
Now make sure re-partition is NOT checked in odin !this is very important! and click start (now wait some time until its finished)
Your phone should reboot automatic (if auto reboot is checked in odin) and the old firmware should be on your phone
Now install towelroot and click "make it rain"
Now you should have root! :laugh:
(Hope this helps. Sorry for my bad english... :crying: )
Have you tried this tutorial?
How to root Samsung Galaxy S3 Neo GT-I9301I
Hopes help.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
cacing32 said:
Have you tried this tutorial?
How to root Samsung Galaxy S3 Neo GT-I9301I
Hopes help.
Click to expand...
Click to collapse
yes, but when I launch app advise that my device isn't supported
Sent from my GT-I9301I
ViktorFoedowski said:
you propably updated to the new version of Kitkat 4.4.2.
The new update had the bandversion I9301IXXUANF4 for me (I updated too) (there is no possible way to root this version as far as i know)
But the not updated version of KitKat 4.4.2 (bandversion for me: I9301IXXUANC6) works with towelroot.
Beside i updated to the new update i still got my phone rooted:
I downloaded the new version of Odin on my pc.
I downloaded the old version from sammobile. (the I9301IXXUANC6 version)
In Odin (launched with admin rights) you click on the PDA (or sometimes AP called) button and select the downloaded firmware version (unpacked)
Next boot your phone in recovery mode (turn it off, then press volume down + home + power button)
Connect your phone to your pc (after that odin should recognize your phone)
Now make sure re-partition is NOT checked in odin !this is very important! and click start (now wait some time until its finished)
Your phone should reboot automatic (if auto reboot is checked in odin) and the old firmware should be on your phone
Now install towelroot and click "make it rain"
Now you should have root! :laugh:
(Hope this helps. Sorry for my bad english... :crying: )
Click to expand...
Click to collapse
one billion of thanks! run perfectly [emoji106]
Sent from my GT-I9301I
rod555 said:
one bullion of thanks! run perfectly
Click to expand...
Click to collapse
No problem. I just wanted to help.
Sent from my GT-I9301I using XDA Premium 4 mobile app
Well, I hope that there will be a root app for I9301IXXUANF4 soon.
I've got some bad memories of doing anything to my phone with ODIN. App is the only non-destructive way for me.
Does anyone know how much time developer needs to release his updated app after new version of Android?
in download mode do you have trace of knox?
i can't understand if it's only a software knox or a hardware one (efuse) like on the s4
you can enter in download mode by doing:
The phone must be turned off.
Keep pressing and holding ‘Home Button (middle button) + Volume down key + Power Button’ simultaneously until you see a warning message. Now press Volume Up to continue. This will land you into downloading mode.
Click to expand...
Click to collapse
If you read "knox warranty etc..." there is a hardware-efuse knox
Help
Hello the root worked. but I can not runterladen..kann the SU file a reinstellen here bitte..soory I can not speak English and write here about the google translator
ViktorFoedowski said:
you propably updated to the new version of Kitkat 4.4.2.
....
Beside i updated to the new update i still got my phone rooted:
....
(Hope this helps. Sorry for my bad english... :crying: )
Click to expand...
Click to collapse
Do you mean that you can downgrade, then root and then again apply the update installing the "F4" version of firmware?
Thanks
Proteusso said:
Do you mean that you can downgrade, then root and then again apply the update installing the "F4" version of firmware?
Thanks
Click to expand...
Click to collapse
No I just wanted to say that I updated my phone to the "F4" version. And after I found that the updated version cannot be rooted I downgraded the phone and rooted it. I am still on the old "C6" version.
Sent from my GT-I9301I using XDA Premium 4 mobile app
Give it a try
ViktorFoedowski said:
No I just wanted to say that I updated my phone to the "F4" version. And after I found that the updated version cannot be rooted I downgraded the phone and rooted it. I am still on the old "C6" version.
Sent from my GT-I9301I using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Hello,
i think we give it a try. Will there be root when you update again?
Harzer30 said:
Hello,
i think we give it a try. Will there be root when you update again?
Click to expand...
Click to collapse
The same question here... Then can I upgrade to ANF4 again with root saved?
BaRTaSs88 said:
Can I upgrade to ANF4 again with root saved?
Click to expand...
Click to collapse
I don't think so but I'm not sure. I didn't try updating with root.
Sent from my GT-I9301I using XDA Premium 4 mobile app
BaRTaSs88 said:
The same question here... Then can I upgrade to ANF4 again with root saved?
Click to expand...
Click to collapse
no, if you upgrade root it's not saved. Until AND3 firmware yes
Sent from my GT-I9301I
Only C6 can be rooted, and as far as I can see there are not that changes with ANF4 and the newer!
So if you really need follow the steps of some posts before!
Related
Hello,
thats my first post
Im je11 from Germany, I registered here, cause its the best forum on the internet for android modding, development, etc.
My Andro-Devices I already had were an Galaxy S2 i9100 (where i already changed the camera firmware to optimze quality of pictures), XPERIA Z and now I have a Samsung Galaxy S4 LTE i9505 ! - Very good smartphone imo.
Problem:
A few days ago I updatet my i9505 SGS IV from 4.2.2 to Stock 4.3 (MJ5) DBT Unbrandet.
Now I got a bad quality of my photos (on 4.2.2 it was much better!)
Where I can download diffrent camera firmwares for my device ? I only need the cameraFW from the 4.2.2.
Its possible ? I already searched on the whole internet - but nothing found :-/
Thank you very much
and sorry for my bad english
Same problem, I would love to know the answer to this
+1
I found the solution ! Open the cameraFW Menu with the combination of numbers and after that i tapped on update - after 5 minutes of updating the quality of pictures get very good ! Tell me if it works
Sent from my GT-I9505 using XDA Premium 4 mobile app
je11 said:
I found the solution ! Open the cameraFW Menu with the combination of numbers and after that i tapped on update - after 5 minutes of updating the quality of pictures get very good ! Tell me if it works
Sent from my GT-I9505 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Explain it step by step pls. Ty :highfive:
Use stock dialler
Punch in *#34971539#
The first option is to click the very first button to check your firmware, then click the second box to check if there is an update.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my GT-I9505 using Tapatalk
nikzDHD said:
Use stock dialler
Punch in *#34971539#
The first option is to click the very first button to check your firmware, then click the second box to check if there is an update.
Click to expand...
Click to collapse
I click in second box, it found an update. It updates correctly and tell me to reboot. It reboots but dont update nothing coz when i go again to see the updates, appears the same update. How can i fix it pls? :highfive:
nikzDHD said:
The first option is to click the very first button to check your firmware, then click the second box to check if there is an update.
Click to expand...
Click to collapse
my secnd button is unclikable, ie its black coloured and i cant click on it ..mayb coz i hv a I9500"?
anu.cool said:
my secnd button is unclikable, ie its black coloured and i cant click on it ..mayb coz i hv a I9500"?
Click to expand...
Click to collapse
No, its coz u have STOCK ROM unrooted :highfive:
Joku1981 said:
No, its coz u have STOCK ROM unrooted :highfive:
Click to expand...
Click to collapse
lol thanks.!
btw any way to upgrade camera fw w/o root?
Joku1981 said:
I click in second box, it found an update. It updates correctly and tell me to reboot. It reboots but dont update nothing coz when i go again to see the updates, appears the same update. How can i fix it pls? :highfive:
Click to expand...
Click to collapse
same here
Sent from my GT-I9505 using xda app-developers app
anu.cool said:
lol thanks.!
btw any way to upgrade camera fw w/o root?
Click to expand...
Click to collapse
I dont think so. The camera fw updates automatically with new firmware version of Stock ROM for that u have this option disabled.
Joku1981 said:
I click in second box, it found an update. It updates correctly and tell me to reboot. It reboots but dont update nothing coz when i go again to see the updates, appears the same update. How can i fix it pls? :highfive:
Click to expand...
Click to collapse
I confirm, the same thing happens with me too.
Joku1981 said:
No, its coz u have STOCK ROM unrooted :highfive:
Click to expand...
Click to collapse
I'm on stock unrooted ROM also, but the buttons are clickable.
Funky-kun said:
I'm on stock unrooted ROM also, but the buttons are clickable.
Click to expand...
Click to collapse
U installed ever non STOCK ROM for sure or rooted OLDER ROM and unrooted installing new Kies Firmware update version. Im wrong?
*EDIT: I have Samsung Galaxy SII, SIII, S4 gt-i9505, Note 3 and all had 2nd option disabled coming of the store when i bought them
btw i have 4.3 and 4.2 s4s and the cam fw is the same.
Sent from my GT-I9505 using xda app-developers app
Funky-kun said:
I confirm, the same thing happens with me too.
I'm on stock unrooted ROM also, but the buttons are clickable.
Click to expand...
Click to collapse
which model of s4 do u have? and what version of android are u using?
worked
Can confirm that this prosec described worked to upgrade camFW on STOCK UNROOTED 4.3 MJ7. Although i do not see a lot of diff. old vs new.
Joku1981 said:
U installed ever non STOCK ROM for sure or rooted OLDER ROM and unrooted installing new Kies Firmware update version. Im wrong?
Click to expand...
Click to collapse
anu.cool said:
which model of s4 do u have? and what version of android are u using?
Click to expand...
Click to collapse
9505 with MK8 firmware.
Never rooted or flashed any rom, just updated through Kies when 4.3 came out.
Joku1981 said:
I click in second box, it found an update. It updates correctly and tell me to reboot. It reboots but dont update nothing coz when i go again to see the updates, appears the same update. How can i fix it pls? :highfive:
Click to expand...
Click to collapse
That's the latest, if you see your current firmware it matches it. As far as I know the last time camera firmware was updated was when 4.3 was first released. When I updated to 4.3 from 4.2.2 and opened the camera for the first time it updated the camera. Maybe later firmwares will bring nearer updates.
Sent from my GT-I9505 using Tapatalk
Android 4.2.2 baseband firmware version
Hello! Please tell me what baseband firmware version that you had before you updated it, I'm asking you because the camera is very useful for me at work, for me this phone is not a toy and unfortunately I was in the same situation with you, my phone was purchased from the store and it's new and it came with Android 4.3 baseband I9505XXUEMKF - the camera was bad like yours, I've updated the baseband firmware to Android 4.4.2 I9505XXUFNB8, the phone was never rooted and I was not installed no custom ROM, I've purchased it on 20 June 2014, I have warranty at it and now after some small researches I've decided to downgrade to 4.2.2 and for that I will send the phone in an Samsung authorized service center but I don't know what baseband firmware version, I want to get best of this mobile because I've made big sacrifices to purchase it because I am needing it. Thank you very much in advance!
Have a nice day!
Best regards!
je11 said:
Hello,
thats my first post
Im je11 from Germany, I registered here, cause its the best forum on the internet for android modding, development, etc.
My Andro-Devices I already had were an Galaxy S2 i9100 (where i already changed the camera firmware to optimze quality of pictures), XPERIA Z and now I have a Samsung Galaxy S4 LTE i9505 ! - Very good smartphone imo.
Problem:
A few days ago I updatet my i9505 SGS IV from 4.2.2 to Stock 4.3 (MJ5) DBT Unbrandet.
Now I got a bad quality of my photos (on 4.2.2 it was much better!)
Where I can download diffrent camera firmwares for my device ? I only need the cameraFW from the 4.2.2.
Its possible ? I already searched on the whole internet - but nothing found :-/
Thank you very much
and sorry for my bad english
Click to expand...
Click to collapse
Hello brothers, Past week i am from Pakistan and past week i upgraded my galaxy s4 gt-i9500 to official android 4.3 , which i downloaded from sammobile, i installed india's firmware as Pakistan has not yet recieved this update, But NOW when i try to downgrade it to official 4.2.2 with ODIN, it says on mobile * Unsupported version* And it also shows * Warranty Bit=0 * what does that mean..
HELP ME ON HOW CAN I DOWNGRADE TO OFFICIAL ANDROID 4.2.2 FOR gt-I9500
masrooraly said:
Hello brothers, Past week i am from Pakistan and past week i upgraded my galaxy s4 gt-i9500 to official android 4.3 , which i downloaded from sammobile, i installed india's firmware as Pakistan has not yet recieved this update, But NOW when i try to downgrade it to official 4.2.2 with ODIN, it says on mobile * Unsupported version* And it also shows * Warranty Bit=0 * what does that mean..
HELP ME ON HOW CAN I DOWNGRADE TO OFFICIAL ANDROID 4.2.2 FOR gt-I9500
Click to expand...
Click to collapse
You can't downgrade because of Samsung's KNOX
BillvanHalen said:
You can't downgrade because of Samsung's KNOX
Click to expand...
Click to collapse
Is there any other way to do this??? because 4.3 has a battery drain bug , i want to downgrade
masrooraly said:
Is there any other way to do this??? because 4.3 has a battery drain bug , i want to downgrade
Click to expand...
Click to collapse
Try to flash a custom rom based on Android 4.3 and equal to your basebandversion
BillvanHalen said:
Try to flash a custom rom based on Android 4.3 and equal to your basebandversion
Click to expand...
Click to collapse
i have never rooted my galaxy s4 gt-i9500 and in odin mode its hows like this
ODIN MODE
PRODUCT NAME: GT-I9500
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
WARRANTY BIT: 0
Do i have KNOX enabled or not ? can you tell ?
masrooraly said:
i have never rooted my galaxy s4 gt-i9500 and in odin mode its hows like this
ODIN MODE
PRODUCT NAME: GT-I9500
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
WARRANTY BIT: 0
Do i have KNOX enabled or not ? can you tell ?
Click to expand...
Click to collapse
Hmm, i don't think the I9500 has KNOX, You could try a Samsung Kies Firmware Upgrade and Initialization, fill in your phone model (GT-I9500), pull out your battery you will see a S/N code/number, fill that in, reboot in download mode and connect to your PC and follow the on-screen Samsung Kies Instructions
YOU WILL LOSE EVERYTHING ON YOUR PHONE SO BACKUP YOUR STORAGE.
BillvanHalen said:
Hmm, i don't think the I9500 has KNOX, You could try a Samsung Kies Firmware Upgrade and Initialization, fill in your phone model (GT-I9500), pull out your battery you will see a S/N code/number, fill that in, reboot in download mode and connect to your PC and follow the on-screen Samsung Kies Instructions
YOU WILL LOSE EVERYTHING ON YOUR PHONE SO BACKUP YOUR STORAGE.
Click to expand...
Click to collapse
this too gives an error * gti9500 does not support inisialization * now what do you suggest ?
masrooraly said:
this too gives an error * gti9500 does not support inisialization * now what do you suggest ?
Click to expand...
Click to collapse
Did you put in: GTI9500 or GT-I9500, because de ' - ' must be entered to regonize, fill this in: GT-I9500
BillvanHalen said:
Did you put in: GTI9500 or GT-I9500, because de ' - ' must be entered to regonize, fill this in: GT-I9500
Click to expand...
Click to collapse
I entered the same which u told , but then ever it shows same error, now what
masrooraly said:
I entered the same which u told , but then ever it shows same error, now what
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Have you choose that option? Because it should be really weird and un-usual if Samsung Kies does not support GT-I9500
BillvanHalen said:
Have you choose that option? Because it should be really weird and un-usual if Samsung Kies does not support GT-I9500
Click to expand...
Click to collapse
Yes i have selected the same for sure
masrooraly said:
Yes i have selected the same for sure
Click to expand...
Click to collapse
Could you place a screenshot of the error you got? Your whole Samsung Kies window?
BillvanHalen said:
Could you place a screenshot of the error you got? Your whole Samsung Kies window?[/QUOTE
See this , now what
Click to expand...
Click to collapse
masrooraly said:
BillvanHalen said:
Could you place a screenshot of the error you got? Your whole Samsung Kies window?[/QUOTE
See this , now what
Click to expand...
Click to collapse
I tested it myself, works for me.
Try to update Samsung Kies? Or maybe you got a weird character filled in because of your region keyboard?
---------- Post added at 02:41 PM ---------- Previous post was at 02:38 PM ----------
BillvanHalen said:
masrooraly said:
I tested it myself, works for me.
Try to update Samsung Kies? Or maybe you got a weird character filled in because of your region keyboard?
Click to expand...
Click to collapse
I think you should update Samsung Kies. It could be Out-dated.
Click to expand...
Click to collapse
Click to expand...
Click to collapse
BillvanHalen said:
masrooraly said:
I tested it myself, works for me.
Try to update Samsung Kies? Or maybe you got a weird character filled in because of your region keyboard?
---------- Post added at 02:41 PM ---------- Previous post was at 02:38 PM ----------
BillvanHalen said:
I think you should update Samsung Kies. It could be Out-dated.
Click to expand...
Click to collapse
i dont know
Click to expand...
Click to collapse
Click to expand...
Click to collapse
masrooraly said:
BillvanHalen said:
masrooraly said:
I tested it myself, works for me.
Try to update Samsung Kies? Or maybe you got a weird character filled in because of your region keyboard?
---------- Post added at 02:41 PM ---------- Previous post was at 02:38 PM ----------
i dont know
Click to expand...
Click to collapse
You are using the old kies for 4.2.2 and downwards. You need Kies 3 because you are on 4.3. Kies 3 supports all android 4.3 devices
Click to expand...
Click to collapse
Click to expand...
Click to collapse
masrooraly said:
BillvanHalen said:
masrooraly said:
I tested it myself, works for me.
Try to update Samsung Kies? Or maybe you got a weird character filled in because of your region keyboard?
---------- Post added at 02:41 PM ---------- Previous post was at 02:38 PM ----------
i dont know
Click to expand...
Click to collapse
Remove Samsung Kies completely, then reinstall it from http://www.samsung.com/
---------- Post added at 02:51 PM ---------- Previous post was at 02:49 PM ----------
Bordo_Bereli51 said:
masrooraly said:
BillvanHalen said:
You are using the old kies for 4.2.2 and downwards. You need Kies 3 because you are on 4.3. Kies 3 supports all android 4.3 devices
Click to expand...
Click to collapse
I tested it with the regular Samsung Kies, not Samsung Kies 3.
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Click to expand...
Click to collapse
BillvanHalen said:
masrooraly said:
BillvanHalen said:
Remove Samsung Kies completely, then reinstall it from http://www.samsung.com/
---------- Post added at 02:51 PM ---------- Previous post was at 02:49 PM ----------
Bordo_Bereli51 said:
masrooraly said:
I tested it with the regular Samsung Kies, not Samsung Kies 3.
Click to expand...
Click to collapse
i have kies 3 too , same prob over there but im updating the regular kies , ill let u know whatever happens
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Click to expand...
Click to collapse
masrooraly said:
i have kies 3 too , same prob over there but im updating the regular kies , ill let u know whatever happens
Click to expand...
Click to collapse
Do this:
Pluggin your Galaxy S4 on PC, launch Kies 3, click on firmware initialisation and then follow the instruction
P.S: It will auto-detect your device see if it's working.
masrooraly said:
BillvanHalen said:
masrooraly said:
BillvanHalen said:
Remove Samsung Kies completely, then reinstall it from http://www.samsung.com/
---------- Post added at 02:51 PM ---------- Previous post was at 02:49 PM ----------
Bordo_Bereli51 said:
i have kies 3 too , same prob over there but im updating the regular kies , ill let u know whatever happens
Click to expand...
Click to collapse
NOW i upgraded the regular kies but the same prob occurs
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Technology: The Ultimate Guide To Unbrick 16 Gb International Samsung Galaxy Note 3 (SM-N9005) And Upgrade To KitKat 4.4.2 Through Custom ROM
Original article, images and videos can be found on Locky's English Playground http://lockyep.blogspot.com/2014/01/technology-ultimate-guide-to-unbrick-16.html
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
And I was going to make a good old demonstration of "how to install Stock KitKat ROM on your SM-N9005", until the whole thing got so out-of-hand... here are my failed attempts compressed into a real short video...
My Note 3 was soft-bricked, meaning that a failure in flashing software has caused my phone to become a 'brick', a not-dead-but-unusable condition.
It was a bummer! But it is one that can hardly avoid having all those upgrade tutorials on YouTube which didn't mention the uniqueness of 16Gb Hong Kong Note 3. Why should they mention anyway? They don't have 16Gb Hong Kong Note 3 in the first place.
Thanks Samsung for making the Hong Kong Note 3 so special, such that it is the Note 3 with the smallest storage in the world (16Gb) when the rest of the world are getting at least 32Gb! For this and for the trouble you have caused Samsung, I hate you!
After 2 days of research, I have finally arrived at a completely, perfectly usable state!!! And it is functioning with speed!!
However, from soft-bricked to success, the road had not been smooth. There was about a day or so that my phone was able to boot and use the internet, but had no in/outgoing call, no sound, no Google Now, no S-Voice, no camera, slow lockscreen and slow settings.
I have followed all the instructions given by several XDA members, but I still could not get it to work. Why?
That's because all those instructions are inaccurate. The thing is, minor details that are missing can be real serious, and for that, I want to write a very very detailed descriptions on how to solve this soft-brick issue specifically for 16 Gb International Samsung Galaxy Note 3 (SM-N9005) when upgrading to KitKat 4.4.2.
Before you start, you'll need,
a Custom ROM, eg. Sweet ROM v7.01 4.4.2 NA6
a leaked N9005XXUENA6 4.4.2 KitKat ROM for Note 3 Download on my blog
a Hong Kong N9005ZHUBMI7 Rescue ROM Download here
the latest CWM Recovery, eg 6.0.4.7 Download on my blog
Odin 3.07 Download on my blog
the latest Samsung USB Driver Download on my blog
Samsung Kies Download on my blog
Note 3 16Gb SM-N9005 from Hong Kong at 50% battery level
a Note 3 USB 3.0 cable
Installation Instructions:
Install Samsung Kies
Install Samsung USB Driver
Connect USB into PC and Note 3, then copy Custom ROM onto the SD card
Put Note 3 into Download mode by holding Power + Volume down + Home buttons at the same time until you see "Warning!!", then press Volume up
When you see "Downloading..." and Android logo, plug in the USB into the PC and Note 3
Run Odin 3.07 (See my video)
When you see a blue 0:[COM4], in the Bootloader put leaked KitKat's BL file, and in PIT, PDA, PHONE, CSC put Hong Kong N9005ZHUBMI7 Rescue ROM's PIT, AP, CP and CS respectively and then press Start to flash.
When Note 3 restarts, it will keep rebooting and it will only show Samsung boot screen, at this time, remove the battery and then put it back.
Repeat Step 4, 5 and 6
In Odin 3.07, go to PDA and choose CWM Recovery, eg 6.0.4.7, and press Start to flash, it will reboot automatically when complete. Unplug the USB.
When the phone reboots, it will boot into CWM Recovery. If it asks you to root phone, just say no. Otherwise, select Wipe data/factory rest --> yes, Wipe Cache --> yes, advance --> Wipe Dalvik Cache --> yes. This will erase the unwanted files and prepare your phone for the good stuff.
Go to install zip --> choose zip from /external_sd and select the Custom ROM you have chosen, then choose yes to flash. This will take about 3 minutes, press reboot after it is completed.
This reboot will be slow, and most likely there will be no sound at boot and errors at setup, be extremely patient and wait for the screen asking you to choose Language to appear. Choose the language you want, press Next, then do nothing else!!!!
Without doing anything else, repeat step 4, 5 and 6.
In Odin 3.07, go to CP, choose leaked KitKat's CP file and then press Start to flash.
When the phone reboots, you should hear the Samsung bootup music and then everything will be functioning perfectly!
The moral of the story is, you have got to have brain and perseverance to work with KitKat 4.4.2.
Only SweetROM can work? Or I can use others such as X-Note? Thanks
Sent from my SM-N9005 with CM11 temasek Unofficial + temasek Kernel via XDA Premium 4 mobile app
raychak said:
Only SweetROM can work? Or I can use others such as X-Note? Thanks
Sent from my SM-N9005 with CM11 temasek Unofficial + temasek Kernel via XDA Premium 4 mobile app
Click to expand...
Click to collapse
Any custom ROM will work.
I have a 16gb Hong Kong Note 3. Firstly I wish to give my congratulations for you, my friend. Fantastic post! Some questions, please:
1- My phone is stock and rooted since the first firmware. I don't upgrade it for the newest version HK Firmware. Is your guide useful for me if I want to update to kit kat and don't wait the official kit kat Hong Kong?
2- After the moment (final part of the guide) that we have to select the language and only check next can I just power off the phone to make easy to start the phone in download Mode to finish the process?
Sorry for my questions and my poor english, my friend. I have read several posts to learn with guys like you. Please let me know. Thank you so much!
Sent from my GT-N8000 using xda app-developers app
JN9 said:
I have a 16gb Hong Kong Note 3. Firstly I wish to give my congratulations for you, my friend. Fantastic post! Some questions, please:
1- My phone is stock and rooted since the first firmware. I don't upgrade it for the newest version HK Firmware. Is your guide useful for me if I want to update to kit kat and don't wait the official kit kat Hong Kong?
2- After the moment (final part of the guide) that we have to select the language and only check next can I just power off the phone to make easy to start the phone in download Mode to finish the process?
Sorry for my questions and my poor english, my friend. I have read several posts to learn with guys like you. Please let me know. Thank you so much!
Sent from my GT-N8000 using xda app-developers app
Click to expand...
Click to collapse
1. Yes, that is exactly what I did and what I thought. I didn't want to wait. I came from stock and rooted 4.3
2. Powering off the phone first, in my opinion, doesn't make going into download mode easier. So just directly hold Power+Vol Down+ Home to get into Download Mode
I am in the same soft brick boat but I have 32gb. I think it's HK as it was shipped from Hong Kong. Will this guide work for me to?
Sent from my HTC One X using xda app-developers app
mabrady85 said:
I am in the same soft brick boat but I have 32gb. I think it's HK as it was shipped from Hong Kong. Will this guide work for me to?
Sent from my HTC One X using xda app-developers app
Click to expand...
Click to collapse
No harm trying. Nothing to lose
Sent from my SM-N9005 using xda app-developers app
will do and will let you know
There is no PIT file in the N9005XXUENA6 zip file
mabrady85 said:
There is no PIT file in the N9005XXUENA6 zip file
Click to expand...
Click to collapse
Exactly, because you have to read more carefully. It is in the N9005ZHUBMI7 Rescue Pack
Locky Loki said:
1. Yes, that is exactly what I did and what I thought. I didn't want to wait. I came from stock and rooted 4.3
2. Powering off the phone first, in my opinion, doesn't make going into download mode easier. So just directly hold Power+Vol Down+ Home to get into Download Mode
Click to expand...
Click to collapse
My friend, I am very grateful for your atention. The guide inside in your blog is fantastic and very rich. I will try to flash kit kat and I will let you know.
Sent from my SM-N9005 using xda app-developers app
JN9 said:
My friend, I am very grateful for your atention. The guide inside in your blog is fantastic and very rich. I will try to flash kit kat and I will let you know.
Sent from my SM-N9005 using xda app-developers app
Click to expand...
Click to collapse
Await for good news
Locky Loki said:
Exactly, because you have to read more carefully. It is in the N9005ZHUBMI7 Rescue Pack
Click to expand...
Click to collapse
Just downloaded the rescue pack but can't find the PIT file...
raychak said:
Just downloaded the rescue pack but can't find the PIT file...
Click to expand...
Click to collapse
You got the download link from my blog?
http://pan.baidu.com/s/1CBNGR
Don't try to find it yourself from Google.
Locky Loki said:
You got the download link from my blog?
http://pan.baidu.com/s/1CBNGR
Click to expand...
Click to collapse
Yes, there are 3 files after extracted.
- The Kernel file unable to view or extract to see the content.
- I extracted the tar.md5 file, but no PIT inside...
Thanks
raychak said:
Yes, there are 3 files after extracted.
- The Kernel file unable to view or extract to see the content.
- I extracted the tar.md5 file, but no PIT inside...
Thanks
Click to expand...
Click to collapse
Please check with this photo
https://drive.google.com/file/d/0B9emHQBd5COmX01jYXJLRjdwMFE/edit?usp=sharing
Your download is probably incomplete or faulty. Try using download manager like JDownloader.
PIT file for you
https://drive.google.com/file/d/0B9emHQBd5COmeGlCeUJaeFh5aGs/edit?usp=sharing
Locky Loki said:
Please check with this photo
https://drive.google.com/file/d/0B9emHQBd5COmX01jYXJLRjdwMFE/edit?usp=sharing
Your download is probably incomplete or faulty. Try using download manager like JDownloader.
PIT file for you
https://drive.google.com/file/d/0B9emHQBd5COmeGlCeUJaeFh5aGs/edit?usp=sharing
Click to expand...
Click to collapse
The file named TGY-N9005ZHUBMI7-20130926192530.rar, is that correct? I downloaded twice with baidu download manager but the downloaded file only contain 3 files, not the files you shown on the photo...
raychak said:
The file named TGY-N9005ZHUBMI7-20130926192530.rar, is that correct? I downloaded twice with baidu download manager but the downloaded file only contain 3 files, not the files you shown on the photo...
Click to expand...
Click to collapse
Try this
http://pan.baidu.com/s/1qxi81
Locky Loki said:
Try this
http://pan.baidu.com/s/1qxi81
Click to expand...
Click to collapse
I just found this version too, downloading now... still not 100% sure I am really want to flash 4.4.2 now as I really don't my Note 3 got soft-bricked during coming few days of holiday. BTW, except from the Note 3 you owned upgraded to 4.4.2 with this method, is there any other user upgraded to 4.4.2 with this method? Thanks
raychak said:
I just found this version too, downloading now... still not 100% sure I am really want to flash 4.4.2 now as I really don't my Note 3 got soft-bricked during coming few days of holiday. BTW, except from the Note 3 you owned upgraded to 4.4.2 with this method, is there any other user upgraded to 4.4.2 with this method? Thanks
Click to expand...
Click to collapse
Get this done and you will have a great holiday.
I suppose many did, many wrote on XDA, but none wrote as detailed as I did.
[Official Lollipop 5.1.1] P600 DOJ3 (Mega & Android File Host) Fast Link + Easy Root
Galaxy Note 10.1 2014 (Wi-Fi) (SM-P600) from region PHE!
Firmware Version Info
(PDA: P600XXUDOJ3 CSC: P600OXADOJ3 CHANGELIST: 6086244 BUILD DATE: 23.10.2015)
It's not rooted and is untoched. It's completely stock!!!
I know others have made posts but they all use ****ty servers. I have uploaded this to Mega and Android File Host as they are both faster and more stable then pony Samsung's crappy servers.
When you flash rom with the setup as in picture it will flash over your previous rom and keep all data and apps and settings.
For maximum stability i recommend after first boot you do factory reset.
SM-P600 Note 10.1 Stock 5.1.1 Rom - Mega: https://mega.nz/#!2x5nmQob
Decription Key : !FU4t1X41UjV9kGmGkw8f-ZxomeyD13nbhL4FqV82AiI
Odin 3.07- Mega : https://mega.nz/#!CsJBQLhR
Decription key : !aSakzROgYonQ-MuKH3vJ_veSxCPcZWElBfZJ6At9Q-4
SM-P600 Note 10.1 Stock 5.1.1 Rom - Android File Host : https://www.androidfilehost.com/?fid=24269982086987868
md5 - 4435246f2bf0620c7acc5406bf189e3a
Odin 3.07 - Android File Host : https://www.androidfilehost.com/?fid=24269982086987869
Rooting guide for 5.1.1 : http://forum.xda-developers.com/showthread.php?p=63637426
TWRP Link : https://dl.twrp.me/lt03wifiue/
[BETA][2015.10.10] SuperSU v2.52 - https://download.chainfire.eu/743/SuperSU/BETA-SuperSU-v2.52.zip
Wanam Xposed Framework & App - http://forum.xda-developers.com/xposed/unofficial-xposed-samsung-lollipop-t3180960
All credit goes to the People running the posts I linked. I didn't do anything but bring it together in one post to save you time running around cyberworld
Easy Guide to Root :
1. Go to Rooting Guide - http://forum.xda-developers.com/showthread.php?p=63637426
Download only the P600 modded boot IMG and then come back here. Move the tar to tablet. "In my opinion that guide is very confusing" This is much more simple...
2. Go to TWRP - https://dl.twrp.me/lt03wifiue/
Download the img.tar This file you keep on pc to flash via Odin.
3. Go to SuperSU v2.52 Beta - https://download.chainfire.eu/743/Su...erSU-v2.52.zip
Download the zip. Move the zip to tablet.
4. Reboot the tablet into download mode and open Odin on the PC then connect the tablet to PC. In Odin click AP tab and locate the TWRP and uncheck Auto-Reboot then hit start. When done hold the power button + vol up button "the vol button furthest from power button" + home button til you see red writing on top right hand corner. This can take a while so don't panic just wait.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5. When finished booting into TWRP pull Spen and click Install then find modded boot img "remember to switch between IMG & ZIP mode in the lower left hand corner" Now flash the boot img. Do not reboot just go back and switch back to ZIP mode and flash SuperSU when done reboot.
6. Wait for the boot to finish. You are now rooted.
I hope this makes it easy for you!!!
Extra Features :
Note 5 Feature "Screen Off App" - http://forum.xda-developers.com/showthread.php?p=62731428
I don't know if this info is important to anyone but if someone wants it then here it is :
This info is from "About Device"
Model number
SM-P600
Android version
5.1.1
Kernel version
3.4.39-6086244
[email protected] #1
Fri Oct 23 17:24:00 KST 2015
Build number
LMY47X.P600XXUDOJ3
SE for Android status
Enforcing
SEPF_SM-P600_5.1.1_0039
Fri Oct 23 18:04:15 2015
KNOX version
KNOX 2.4.1
Standard SDK 5.4.1
Premium SDK 2.4.1
Customization SDK 2.4.0
Container 2.4.1
CEP 2.0.1
OTP 1.1.1
SE for Android 2.3.0
SSO 2.4.1
TIMA 3.0
VPN 2.2.0
Zionator said:
Galaxy Note 10.1 2014 (Wi-Fi) (SM-P600) from region PHE!
Firmware Version Info
(PDA: P600XXUDOJ3 CSC: P600OXADOJ3 CHANGELIST: 6086244 BUILD DATE: 23.10.2015)
It's not rooted and is untoched. It's completely stock!!!
I know others have made posts but they all use ****ty servers. I have uploaded this to Mega and Android File Host as they are both faster and more stable then pony Samsung's crappy servers.
When you flash rom with the setup as in picture it will flash over your previous rom and keep all data and apps and settings.
For maximum stability i recommend after first boot you do factory reset.
SM-P600 Note 10.1 Stock 5.1.1 Rom - Mega: https://mega.nz/#!2x5nmQob
Decription Key : !FU4t1X41UjV9kGmGkw8f-ZxomeyD13nbhL4FqV82AiI
Odin 3.07- Mega : https://mega.nz/#!CsJBQLhR
Decription key : !aSakzROgYonQ-MuKH3vJ_veSxCPcZWElBfZJ6At9Q-4
SM-P600 Note 10.1 Stock 5.1.1 Rom - Android File Host : https://www.androidfilehost.com/?fid=24269982086987868
md5 - 4435246f2bf0620c7acc5406bf189e3a
Odin 3.07- Android File Host : https://www.androidfilehost.com/?fid=24269982086987869
If you want root then there is a post here offering that ROOT : http://forum.xda-developers.com/galaxy-note-10-2014/general/root-root-stock-kernel-t3240218
Click to expand...
Click to collapse
Thank you. And did you root it successfully? I cannot flash a twrp.
What about region
Whats the difference if my region is not this and i update?
Thank you for links. I wonder what if I install it over 4.3 instead of 4.4.2. Is there any difference?
iopxiang said:
Thank you. And did you root it successfully? I cannot flash a twrp.
Click to expand...
Click to collapse
Not yet I will wait a few days to do anything as I just want to see how it works and the battery life on stock. Then I will root and remove many system bloatware apps and see the difference.
rbaleiro said:
Whats the difference if my region is not this and i update?
Click to expand...
Click to collapse
This is the Spanish region but I live in UK and at the very first setup screen I chose UK language so it don't really matter about the region as there is no modem. This device is just WiFi so region makes no difference.
chengineer said:
Thank you for links. I wonder what if I install it over 4.3 instead of 4.4.2. Is there any difference?
Click to expand...
Click to collapse
You are welcome. Well I flashed this over a custom rom Hyperdrive 4.4.2 and then once it booted I then factory reset it. Before I factory reset the device it was fine I just like the fresness of roms.
So the answer to your question is I don't know but I don't think it will make a difference as the bootloader is in the rom and will be flashed automatically with the rom. I came from 4.4.2 so I cannot speak about 4.3 but I assume it will be the same result.
Sent from my SM-N920C using Tapatalk
Thanks, Ill install too and see what happens!
Just installed! It's running very smoothly. I just realised that they don't have the internal game lollipop when u push the version of the OS. Lol!
rbaleiro said:
Thanks, Ill install too and see what happens!
Click to expand...
Click to collapse
You're welcome.
rbaleiro said:
Just installed! It's running very smoothly. I just realised that they don't have the internal game lollipop when u push the version of the OS. Lol!
Click to expand...
Click to collapse
Yes I have been waiting for this lollipop for ages now. Just hope someone cooks up a lovely custom rom soon ?
Sent from my SM-N920C using Tapatalk
Thank you so much for taking time to write each step in details. This made life so easier. You are right the other guide is little complicated. I was not aware that touch does not work in twrp also was not unchecking auto root. But then I came across your guide and believe me it's so easy. Thanks again, I rooted successfully.
vinayburman said:
Thank you so much for taking time to write each step in details. This made life so easier. You are right the other guide is little complicated. I was not aware that touch does not work in twrp also was not unchecking auto root. But then I came across your guide and believe me it's so easy. Thanks again, I rooted successfully.
Click to expand...
Click to collapse
Touch (as well as all other functions) works in twrp 2.8.6
Sent from my SM-P600 using XDA Free mobile app
I can't thank you enough. I flashed 5.1.1 yesterday and everything was working fine, but I was really missing root. I could NOT wrap my head around the root process as described in the other posts. Nothing against all their hard work, I'm just slow. Your step by step was so easy to follow! Now I'm rooted and happy. Thanks!!
Guys, a question.
If i want to clean install Lollipop with full wipes using Odin on the SM-P601, which is currently on the UAE csc, using the INU csc, what are the steps i should follow.?
And if i factory reset using the recovery, will all my files in the internal storage get deleted.?
Any help would be appreciated.
Thanks. ☺
Will it work i have 5.0.1 one on my phone
countryboy1000000 said:
Will it work i have 5.0.1 one on my phone
Click to expand...
Click to collapse
Yes, it should, even you have custom rom.
---------- Post added at 06:02 PM ---------- Previous post was at 05:59 PM ----------
amey2606 said:
Guys, a question.
If i want to clean install Lollipop with full wipes using Odin on the SM-P601, which is currently on the UAE csc, using the INU csc, what are the steps i should follow.?
And if i factory reset using the recovery, will all my files in the internal storage get deleted.?
Any help would be appreciated.
Thanks.
Click to expand...
Click to collapse
Yes, factory reset is like you just brought the tablet from the store.
vinayburman said:
Thank you so much for taking time to write each step in details. This made life so easier. You are right the other guide is little complicated. I was not aware that touch does not work in twrp also was not unchecking auto root. But then I came across your guide and believe me it's so easy. Thanks again, I rooted successfully.
Click to expand...
Click to collapse
You are welcome. I am glad you got it rooted. First thing I did was debloating like a mad man hehe.
Then exposed and now I am gonna try and find working themes for it ?
Sent from my SM-N666F "Special Edition"
Any idea if the root will work on P605 too? It's got 5.1.1 as well and I'm pretty excited to get on it. However, not may people are discussing about it.
Thanks for the guide btw!
MasK said:
Any idea if the root will work on P605 too? It's got 5.1.1 as well and I'm pretty excited to get on it. However, not may people are discussing about it.
Thanks for the guide btw!
Click to expand...
Click to collapse
Yes it will work if u download the 605 rom and then from root post download the modded boot image for 605 if available and last thing get TWRP for 605 as well.
Do as described in my guide and apart from what I said above the rest is universal meaning that supersu and closed are the same for all versions.
Sent from my SM-P600 using Tapatalk
for sm-p601
Can you please give a link for sm-p601 too
Zionator said:
4. Reboot the tablet into download mode and open Odin on the PC then connect the tablet to PC. In Odin click AP tab and locate the TWRP and uncheck Auto-Reboot then hit start. When done hold the power button + vol up button "the vol button furthest from power button" + home button til you see red writing on top right hand corner. This can take a while so don't panic just wait.
Click to expand...
Click to collapse
as I held these three buttons, I watched as the Samsung note splash screen flickered and restarted over and over. I held for about 10 minute and gave up after my hands got tired. After that, I couldn't get past the splash screen and had to do a straight ROM via ODIN.....can I still root? What was I doing wrong??
Need Recovery for 2.27.707.1 Asia WWE
Marshmallow
CID 038(If this is required)
Tried installing the new ota with an older recovery after restoring unmodified system image from twrp and it failed.
So i assume the newer recovery is needed...
Thanks for the help!
i in same situation i flsh twrp then cleanstate now im bricked. if someone has twrp backup. if its works... i dunno. also i tried to update b4 get twrp recovery but my cel got stuck at 25%
i need this recovery too......new ota dont install and stuck on 25%.....
do you have twrp stock backup?
---------- Post added at 03:13 AM ---------- Previous post was at 03:12 AM ----------
T3snake said:
Need Recovery for 2.27.707.1 Asia WWE
Marshmallow
CID 038(If this is required)
Tried installing the new ota with an older recovery after restoring unmodified system image from twrp and it failed.
So i assume the newer recovery is needed...
Thanks for the help!
Click to expand...
Click to collapse
do you have twrp stock bakup?
alexmegamass said:
do you have twrp stock backup?
---------- Post added at 03:13 AM ---------- Previous post was at 03:12 AM ----------
do you have twrp stock bakup?
Click to expand...
Click to collapse
Yes i do
T3snake said:
Yes i do
Click to expand...
Click to collapse
is there a chance for me to get it so I can restore my cell? Because I flash cleanslate now I have no signal .,.. thanks In advance . If you can upload it to mega...plz.i did not make any backup of my stock ROM
Sent from my SM-J700H using Tapatalk
alexmegamass said:
is there a chance for me to get it so I can restore my cell? Because I flash cleanslate now I have no signal .,.. thanks In advance . If you can upload it to mega...plz.i did not make any backup of my stock ROM
Sent from my SM-J700H using Tapatalk
Click to expand...
Click to collapse
which cleanslate version did you flash?
did you try the older version if the newer one didnt work?
Uploading right now will post link tommorow... though not sure if my backup will work on your device
alexmegamass said:
is there a chance for me to get it so I can restore my cell? Because I flash cleanslate now I have no signal .,.. thanks In advance . If you can upload it to mega...plz.i did not make any backup of my stock ROM
Sent from my SM-J700H using Tapatalk
Click to expand...
Click to collapse
there you go...
https://mega.nz/#!4tUC0CxJ!zt0H6rrhKN4J8q52VImQRffoUu3A5OEMtY4UVk1f75s
system backup twrp 2.27.707.1
T3snake said:
there you go...
https://mega.nz/#!4tUC0CxJ!zt0H6rrhKN4J8q52VImQRffoUu3A5OEMtY4UVk1f75s
system backup twrp 2.27.707.1
Click to expand...
Click to collapse
Thanks I will try your backup . I flashed 1.2.3. cleanslate Europe. But my cellphone is like turning off airplane mode and it shows no imei number neither baseband info.
Sent from my SM-J700H using Tapatalk
alexmegamass said:
Thanks I will try your backup . I flashed 1.2.3. cleanslate Europe. But my cellphone is like turning off airplane mode and it shows no imei number neither baseband info.
Sent from my SM-J700H using Tapatalk
Click to expand...
Click to collapse
I'm back now I have signal GSM 3G and LTE but my camera is not working. Lol. I should reflash firmware.zip? My system is even showing update for 530mb
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my HTC One M9PLUS using Tapatalk
T3snake said:
Need Recovery for 2.27.707.1 Asia WWE
Marshmallow
CID 038(If this is required)
Tried installing the new ota with an older recovery after restoring unmodified system image from twrp and it failed.
So i assume the newer recovery is needed...
Thanks for the help!
Click to expand...
Click to collapse
I did some kinda magic with my old update file ... This is stock recovery .. https://mega.nz/#!Bc5xzApA for 2.27.707.1 unzip rename to recovery and try to get new OTA 2.30.707.1 .. let me know if you could install it . I'm now trying to solve camera issue ... It's closing app now even showing img
Sent from my SM-J700H using Tapatalk
alexmegamass said:
I did some kinda magic with my old update file ... This is stock recovery .. https://mega.nz/#!Bc5xzApA for 2.27.707.1 unzip rename to recovery and try to get new OTA 2.30.707.1 .. let me know if you could install it . I'm now trying to solve camera issue ... It's closing app now even showing img
Sent from my SM-J700H using Tapatalk
Click to expand...
Click to collapse
what is dec key bro ??? tell pls...i needed this recovery
DJ Mohammad KHAN said:
what is dec key bro ??? tell pls...i needed this recovery
Click to expand...
Click to collapse
WOW I did not put any key I found it now please check your inbox.
Sent from my SM-J700H using Tapatalk
alexmegamass said:
I did some kinda magic with my old update file ... This is stock recovery .. https://mega.nz/#!Bc5xzApA for 2.27.707.1 unzip rename to recovery and try to get new OTA 2.30.707.1 .. let me know if you could install it . I'm now trying to solve camera issue ... It's closing app now even showing img
Sent from my SM-J700H using Tapatalk
Click to expand...
Click to collapse
downloaded and test it and tell you how it working...
i flashed this recovery and test install ota update.....again setup stuck in 25% and then error and reboot.....didn't work again....
DJ Mohammad KHAN said:
i flashed this recovery and test install ota update.....again setup stuck in 25% and then error and reboot.....didn't work again....
Click to expand...
Click to collapse
Lets await for T3SNAKE if he can update we can restore from his backup TWRP. Because mines is not installing it's pop up advice that my software is modified.. after download 500mb update
Sent from my HTC One M9PLUS using Tapatalk
alexmegamass said:
Lets await for T3SNAKE if he can update we can restore from his backup TWRP. Because mines is not installing it's pop up advice that my software is modified.. after download 500mb update
Sent from my HTC One M9PLUS using Tapatalk
Click to expand...
Click to collapse
i think we must find full RUU 2.30.707.1 and flash this to fix this problem....othervise we no way for fix it.....i try many way and always update stuck in 25%
DJ Mohammad KHAN said:
i think we must find full RUU 2.30.707.1 and flash this to fix this problem....othervise we no way for fix it.....i try many way and always update stuck in 25%
Click to expand...
Click to collapse
Yours is rooted ? I can't update because I'm super CID and it's pop up message that my cellphone is modified...Also my camera app is not opening I downloaded other camera app also is not working..
Sent from my HTC One M9PLUS using Tapatalk
alexmegamass said:
Yours is rooted ? I can't update because I'm super CID and it's pop up message that my cellphone is modified...Also my camera app is not opening I downloaded other camera app also is not working..
Sent from my HTC One M9PLUS using Tapatalk
Click to expand...
Click to collapse
my friend go to this link : http://www.apkmirror.com/apk/htc-corporation/htc-camera-new/
download different camera.apk from here and install on your device...
maybe fix your problem....
othervise your problem is hardware issue...
DJ Mohammad KHAN said:
my friend go to this link : http://www.apkmirror.com/apk/htc-corporation/htc-camera-new/
download different camera.apk from here and install on your device...
maybe fix your problem....
othervise your problem is hardware issue...
Click to expand...
Click to collapse
Not working. Dunno maybe camera driver ??
Sent from my HTC One M9PLUS using Tapatalk