Hi ,
I soft bricked my huawei honor 3c and have successfully resolved the issue . My phone was in boot loop and i could not Unbrick it with SDCRAD firmware auto update . So i had to flash the original signed recovery (link below) and then i could auto update from the SDCARD . The complete tutorial and links to files used is in the following link.
https://forum.lowyat.net/index.php?showtopic=3237141&st=1260&p=68534687&#entry68534687
I thought ill post it to help others having the same problem and also the additional steps that i performed.
You have to have the Service drivers and SP Flash tool version available on the above link.
Troubleshooting
if your phone is not detecting drivers and is in a loop of vibrating after every few seconds , then remove the battery , connect it to the computer and immediately put the battery back. If its still not working , then probably you need to remove and reinstall the drivers.
Disclaimer
I did not write the guide available at the above link , I only share the above resources and will not be responsible for any consequences with your phone and yourself for using the files and information above. Flash at your own risk and I cannot guarantee your success.
How do i use sp flash to unbrick. pls help me.
Hello,
i have huawei honor 3c h30-u10 phone. The prophet i am facing is when i calls to anyone there is robotic voice others person hearing when i speak, but disconnecting and call second time remove this problem. I am facing this often and costing money due to extra calls.
Anyone has any idea what is wrong?
What to do with no recovery and only vibration
My mobile is vibrationg like anything ...no power on , no recovery , no charging ... What should i do now?
styleevijesh said:
My mobile is vibrationg like anything ...no power on , no recovery , no charging ... What should i do now?
Click to expand...
Click to collapse
I encountered the same issue. hopefully someone will help and post a step by step solution.
thanks a lot in advance.
huawei honor h30-u10 keep restarting on logo
please help me how can i fix this issue.
obrhyn said:
I encountered the same issue. hopefully someone will help and post a step by step solution.
thanks a lot in advance.
Click to expand...
Click to collapse
same problem with my phone,
please help
putrafatih said:
same problem with my phone,
please help
Click to expand...
Click to collapse
The problem has been resolved
solution :
1. Install the required MTK USB drivers you downloaded earlier.
2. Download SP Flash Tool.zip on your PC and extract its contents.
3. Next, download “Honor3CBootUnlock.zip” on the computer and unzip it too.
4. Execute “FlashTool.exe” on the PC.
5. Click “Scatter-loading” and select “MT6582_Android_scatter” file placed inside “Honor3CBootUnlock” folder.
6. After that, click Window menu and check “Write Memory”. A new tab named Write Memory should appear.
7. In Write Memory tab, click Open Raw Data and select “preloader_huawei82_wet_jb5.bin”.
8. Set Memory Setting to “EMMC”, Beginning Address to “0x800” and Container Length to “0x1B0EC”. Finally click Write Memory button,SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
9. GREEN circle will be displayed if the download succeeded.
10. Now DISCONNECT the USB cable from your phone.
11. Download stock ROM for your EU set V100R001C432B111 (739 MB)
12. extract the file H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue.zip
13. Execute “FlashTool.exe” on the PC, Go to Download tab
14. click [Scatter-loading] and Select the extracted folder 'H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue' and click 'Open'.
15. Select 'MT6582_Android_scatter.txt' found in the signed ROM folder and click 'Open'.
16. The partitions info should be loaded, make sure ALL items are checked.
17. Press [Firmware Upgrade] button or 'F8' on keyboard.
18. SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
19. SPFT has successfully established a connection with the phone, the upgrade process will begin.
20. SP FlashTool will verify the input images and begin writing to the phone EMMC once the verification succeeded.
21. Upgrade in progress, this may take a few minutes...
22. GREEN circle will be displayed if the upgrade succeeded.
23. Now DISCONNECT the USB cable from your phone.
24. Re-insert battery to your phone, press [Volume Up] + [Power] button to enter recovery.
25. Perform a 'Factory Reset/Wipe data' before booting from the rom for the first time.
---------- Post added at 03:14 AM ---------- Previous post was at 03:10 AM ----------
styleevijesh said:
My mobile is vibrationg like anything ...no power on , no recovery , no charging ... What should i do now?
Click to expand...
Click to collapse
the issue like my phone ,but I have successfully resolved the issue.
solution :
1. Install the required MTK USB drivers you downloaded earlier.
2. Download SP Flash Tool.zip on your PC and extract its contents.
3. Next, download “Honor3CBootUnlock.zip” on the computer and unzip it too.
4. Execute “FlashTool.exe” on the PC.
5. Click “Scatter-loading” and select “MT6582_Android_scatter” file placed inside “Honor3CBootUnlock” folder.
6. After that, click Window menu and check “Write Memory”. A new tab named Write Memory should appear.
7. In Write Memory tab, click Open Raw Data and select “preloader_huawei82_wet_jb5.bin”.
8. Set Memory Setting to “EMMC”, Beginning Address to “0x800” and Container Length to “0x1B0EC”. Finally click Write Memory button,SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
9. GREEN circle will be displayed if the download succeeded.
10. Now DISCONNECT the USB cable from your phone.
11. Download stock ROM for your EU set V100R001C432B111 (739 MB)
12. extract the file H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue.zip
13. Execute “FlashTool.exe” on the PC, Go to Download tab
14. click [Scatter-loading] and Select the extracted folder 'H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue' and click 'Open'.
15. Select 'MT6582_Android_scatter.txt' found in the signed ROM folder and click 'Open'.
16. The partitions info should be loaded, make sure ALL items are checked.
17. Press [Firmware Upgrade] button or 'F8' on keyboard.
18. SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
19. SPFT has successfully established a connection with the phone, the upgrade process will begin.
20. SP FlashTool will verify the input images and begin writing to the phone EMMC once the verification succeeded.
21. Upgrade in progress, this may take a few minutes...
22. GREEN circle will be displayed if the upgrade succeeded.
23. Now DISCONNECT the USB cable from your phone.
24. Re-insert battery to your phone, press [Volume Up] + [Power] button to enter recovery.
25. Perform a 'Factory Reset/Wipe data' before booting from the rom for the first time.
^^ hi. how do you resolve the vibrating issue? thank you
still not working for me. my h30-u10 keeps vibrating. flashtool succeeded. but nothing happend. still vibrating
putrafatih said:
The problem has been resolved
solution :
1. Install the required MTK USB drivers you downloaded earlier.
2. Download SP Flash Tool.zip on your PC and extract its contents.
3. Next, download “Honor3CBootUnlock.zip” on the computer and unzip it too.
4. Execute “FlashTool.exe” on the PC.
5. Click “Scatter-loading” and select “MT6582_Android_scatter” file placed inside “Honor3CBootUnlock” folder.
6. After that, click Window menu and check “Write Memory”. A new tab named Write Memory should appear.
7. In Write Memory tab, click Open Raw Data and select “preloader_huawei82_wet_jb5.bin”.
8. Set Memory Setting to “EMMC”, Beginning Address to “0x800” and Container Length to “0x1B0EC”. Finally click Write Memory button,SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
9. GREEN circle will be displayed if the download succeeded.
10. Now DISCONNECT the USB cable from your phone.
11. Download stock ROM for your EU set V100R001C432B111 (739 MB)
12. extract the file H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue.zip
13. Execute “FlashTool.exe” on the PC, Go to Download tab
14. click [Scatter-loading] and Select the extracted folder 'H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue' and click 'Open'.
15. Select 'MT6582_Android_scatter.txt' found in the signed ROM folder and click 'Open'.
16. The partitions info should be loaded, make sure ALL items are checked.
17. Press [Firmware Upgrade] button or 'F8' on keyboard.
18. SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
19. SPFT has successfully established a connection with the phone, the upgrade process will begin.
20. SP FlashTool will verify the input images and begin writing to the phone EMMC once the verification succeeded.
21. Upgrade in progress, this may take a few minutes...
22. GREEN circle will be displayed if the upgrade succeeded.
23. Now DISCONNECT the USB cable from your phone.
24. Re-insert battery to your phone, press [Volume Up] + [Power] button to enter recovery.
25. Perform a 'Factory Reset/Wipe data' before booting from the rom for the first time.
---------- Post added at 03:14 AM ---------- Previous post was at 03:10 AM ----------
the issue like my phone ,but I have successfully resolved the issue.
solution :
1. Install the required MTK USB drivers you downloaded earlier.
2. Download SP Flash Tool.zip on your PC and extract its contents.
3. Next, download “Honor3CBootUnlock.zip” on the computer and unzip it too.
4. Execute “FlashTool.exe” on the PC.
5. Click “Scatter-loading” and select “MT6582_Android_scatter” file placed inside “Honor3CBootUnlock” folder.
6. After that, click Window menu and check “Write Memory”. A new tab named Write Memory should appear.
7. In Write Memory tab, click Open Raw Data and select “preloader_huawei82_wet_jb5.bin”.
8. Set Memory Setting to “EMMC”, Beginning Address to “0x800” and Container Length to “0x1B0EC”. Finally click Write Memory button,SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
9. GREEN circle will be displayed if the download succeeded.
10. Now DISCONNECT the USB cable from your phone.
11. Download stock ROM for your EU set V100R001C432B111 (739 MB)
12. extract the file H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue.zip
13. Execute “FlashTool.exe” on the PC, Go to Download tab
14. click [Scatter-loading] and Select the extracted folder 'H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue' and click 'Open'.
15. Select 'MT6582_Android_scatter.txt' found in the signed ROM folder and click 'Open'.
16. The partitions info should be loaded, make sure ALL items are checked.
17. Press [Firmware Upgrade] button or 'F8' on keyboard.
18. SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
19. SPFT has successfully established a connection with the phone, the upgrade process will begin.
20. SP FlashTool will verify the input images and begin writing to the phone EMMC once the verification succeeded.
21. Upgrade in progress, this may take a few minutes...
22. GREEN circle will be displayed if the upgrade succeeded.
23. Now DISCONNECT the USB cable from your phone.
24. Re-insert battery to your phone, press [Volume Up] + [Power] button to enter recovery.
25. Perform a 'Factory Reset/Wipe data' before booting from the rom for the first time.
Click to expand...
Click to collapse
Thanks mate your method work for me and now i can use my mobile normally. once again thanks man. and please upload the relevant file link or their forum area ..
putrafatih said:
solution :
1. Install the required MTK USB drivers you downloaded earlier.
2. Download SP Flash Tool.zip on your PC and extract its contents.
3. Next, download “Honor3CBootUnlock.zip” on the computer and unzip it too.
4. Execute “FlashTool.exe” on the PC.
5. Click “Scatter-loading” and select “MT6582_Android_scatter” file placed inside “Honor3CBootUnlock” folder.
6. After that, click Window menu and check “Write Memory”. A new tab named Write Memory should appear.
7. In Write Memory tab, click Open Raw Data and select “preloader_huawei82_wet_jb5.bin”.
8. Set Memory Setting to “EMMC”, Beginning Address to “0x800” and Container Length to “0x1B0EC”. Finally click Write Memory button,SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
9. GREEN circle will be displayed if the download succeeded.
10. Now DISCONNECT the USB cable from your phone.
11. Download stock ROM for your EU set V100R001C432B111 (739 MB)
12. extract the file H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue.zip
13. Execute “FlashTool.exe” on the PC, Go to Download tab
14. click [Scatter-loading] and Select the extracted folder 'H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue' and click 'Open'.
15. Select 'MT6582_Android_scatter.txt' found in the signed ROM folder and click 'Open'.
16. The partitions info should be loaded, make sure ALL items are checked.
17. Press [Firmware Upgrade] button or 'F8' on keyboard.
18. SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
19. SPFT has successfully established a connection with the phone, the upgrade process will begin.
20. SP FlashTool will verify the input images and begin writing to the phone EMMC once the verification succeeded.
21. Upgrade in progress, this may take a few minutes...
22. GREEN circle will be displayed if the upgrade succeeded.
23. Now DISCONNECT the USB cable from your phone.
24. Re-insert battery to your phone, press [Volume Up] + [Power] button to enter recovery.
25. Perform a 'Factory Reset/Wipe data' before booting from the rom for the first time.
Click to expand...
Click to collapse
I have the same problem but when I press [Firmware Upgrade] an error saying "No Valid Partition Management Table (PMT) for storage device", When press download an error saying "s security ac region not found in secro img"
Any help????????
No3man said:
I have the same problem but when I press [Firmware Upgrade] an error saying "No Valid Partition Management Table (PMT) for storage device", When press download an error saying "s security ac region not found in secro img"
Any help????????
Click to expand...
Click to collapse
Same Problem here... Found any solutions???
No3man said:
I have the same problem but when I press [Firmware Upgrade] an error saying "No Valid Partition Management Table (PMT) for storage device", When press download an error saying "s security ac region not found in secro img"
Any help????????
Click to expand...
Click to collapse
Any update????
No3man said:
I have the same problem but when I press [Firmware Upgrade] an error saying "No Valid Partition Management Table (PMT) for storage device", When press download an error saying "s security ac region not found in secro img"
Any help????????
Click to expand...
Click to collapse
click on DA dl all with checksum
Not work for me what can i do now i have honor 3c vibrate only
bazaid said:
Not work for me what can i do now i have honor 3c vibrate only
Click to expand...
Click to collapse
Watch tutorials on Youtube for step by step process.
Sent from my Galaxy Tab 3 using XDA Labs
Honor 3c vibrates only
adriansticoid said:
Watch tutorials on Youtube for step by step process.
Sent from my Galaxy Tab 3 using XDA Labs
Click to expand...
Click to collapse
I follow the steps
1. Install the required MTK USB drivers you downloaded earlier.
2. Download SP Flash Tool.zip on your PC and extract its contents.
3. Next, download “Honor3CBootUnlock.zip” on the computer and unzip it too.
4. Execute “FlashTool.exe” on the PC.
5. Click “Scatter-loading” and select “MT6582_Android_scatter” file placed inside “Honor3CBootUnlock” folder.
6. After that, click Window menu and check “Write Memory”. A new tab named Write Memory should appear.
7. In Write Memory tab, click Open Raw Data and select “preloader_huawei82_wet_jb5.bin”.
8. Set Memory Setting to “EMMC”, Beginning Address to “0x800” and Container Length to “0x1B0EC”. Finally click Write Memory button,SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
9. GREEN circle will be displayed if the download succeeded.
10. Now DISCONNECT the USB cable from your phone.
11. Download stock ROM for your EU set V100R001C432B111 (739 MB)
12. extract the file H30-U10_Firmware_V100R001C432B111_Norwegian_operatorVa lue.zip
13. Execute “FlashTool.exe” on the PC, Go to Download tab
14. click [Scatter-loading] and Select the extracted folder 'H30-U10_Firmware_V100R001C432B111_Norwegian_operatorVa lue' and click 'Open'.
15. Select 'MT6582_Android_scatter.txt' found in the signed ROM folder and click 'Open'.
16. The partitions info should be loaded, make sure ALL items are checked.
17. Press [Firmware Upgrade] button or 'F8' on keyboard.
18. SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
19. SPFT has successfully established a connection with the phone, the upgrade process will begin.
20. SP FlashTool will verify the input images and begin writing to the phone EMMC once the verification succeeded.
21. Upgrade in progress, this may take a few minutes...
22. GREEN circle will be displayed if the upgrade succeeded.
23. Now DISCONNECT the USB cable from your phone.
But my 3c still vibrates only after success full flashing
Also flash with b108 signed but noworks
bazaid said:
I follow the steps
1. Install the required MTK USB drivers you downloaded earlier.
2. Download SP Flash Tool.zip on your PC and extract its contents.
3. Next, download “Honor3CBootUnlock.zip” on the computer and unzip it too.
4. Execute “FlashTool.exe” on the PC.
5. Click “Scatter-loading” and select “MT6582_Android_scatter” file placed inside “Honor3CBootUnlock” folder.
6. After that, click Window menu and check “Write Memory”. A new tab named Write Memory should appear.
7. In Write Memory tab, click Open Raw Data and select “preloader_huawei82_wet_jb5.bin”.
8. Set Memory Setting to “EMMC”, Beginning Address to “0x800” and Container Length to “0x1B0EC”. Finally click Write Memory button,SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
9. GREEN circle will be displayed if the download succeeded.
10. Now DISCONNECT the USB cable from your phone.
11. Download stock ROM for your EU set V100R001C432B111 (739 MB)
12. extract the file H30-U10_Firmware_V100R001C432B111_Norwegian_operatorVa lue.zip
13. Execute “FlashTool.exe” on the PC, Go to Download tab
14. click [Scatter-loading] and Select the extracted folder 'H30-U10_Firmware_V100R001C432B111_Norwegian_operatorVa lue' and click 'Open'.
15. Select 'MT6582_Android_scatter.txt' found in the signed ROM folder and click 'Open'.
16. The partitions info should be loaded, make sure ALL items are checked.
17. Press [Firmware Upgrade] button or 'F8' on keyboard.
18. SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
19. SPFT has successfully established a connection with the phone, the upgrade process will begin.
20. SP FlashTool will verify the input images and begin writing to the phone EMMC once the verification succeeded.
21. Upgrade in progress, this may take a few minutes...
22. GREEN circle will be displayed if the upgrade succeeded.
23. Now DISCONNECT the USB cable from your phone.
But my 3c still vibrates only after success full flashing
Also flash with b108 signed but noworks
Click to expand...
Click to collapse
Maybe your partitions are destroyed now.
Sent from my honor 5X using XDA Labs
putrafatih said:
The problem has been resolved
solution :
1. Install the required MTK USB drivers you downloaded earlier.
2. Download SP Flash Tool.zip on your PC and extract its contents.
3. Next, download “Honor3CBootUnlock.zip” on the computer and unzip it too.
4. Execute “FlashTool.exe” on the PC.
5. Click “Scatter-loading” and select “MT6582_Android_scatter” file placed inside “Honor3CBootUnlock” folder.
6. After that, click Window menu and check “Write Memory”. A new tab named Write Memory should appear.
7. In Write Memory tab, click Open Raw Data and select “preloader_huawei82_wet_jb5.bin”.
8. Set Memory Setting to “EMMC”, Beginning Address to “0x800” and Container Length to “0x1B0EC”. Finally click Write Memory button,SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
9. GREEN circle will be displayed if the download succeeded.
10. Now DISCONNECT the USB cable from your phone.
11. Download stock ROM for your EU set V100R001C432B111 (739 MB)
12. extract the file H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue.zip
13. Execute “FlashTool.exe” on the PC, Go to Download tab
14. click [Scatter-loading] and Select the extracted folder 'H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue' and click 'Open'.
15. Select 'MT6582_Android_scatter.txt' found in the signed ROM folder and click 'Open'.
16. The partitions info should be loaded, make sure ALL items are checked.
17. Press [Firmware Upgrade] button or 'F8' on keyboard.
18. SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
19. SPFT has successfully established a connection with the phone, the upgrade process will begin.
20. SP FlashTool will verify the input images and begin writing to the phone EMMC once the verification succeeded.
21. Upgrade in progress, this may take a few minutes...
22. GREEN circle will be displayed if the upgrade succeeded.
23. Now DISCONNECT the USB cable from your phone.
24. Re-insert battery to your phone, press [Volume Up] + [Power] button to enter recovery.
25. Perform a 'Factory Reset/Wipe data' before booting from the rom for the first time.
---------- Post added at 03:14 AM ---------- Previous post was at 03:10 AM ----------
the issue like my phone ,but I have successfully resolved the issue.
solution :
1. Install the required MTK USB drivers you downloaded earlier.
2. Download SP Flash Tool.zip on your PC and extract its contents.
3. Next, download “Honor3CBootUnlock.zip” on the computer and unzip it too.
4. Execute “FlashTool.exe” on the PC.
5. Click “Scatter-loading” and select “MT6582_Android_scatter” file placed inside “Honor3CBootUnlock” folder.
6. After that, click Window menu and check “Write Memory”. A new tab named Write Memory should appear.
7. In Write Memory tab, click Open Raw Data and select “preloader_huawei82_wet_jb5.bin”.
8. Set Memory Setting to “EMMC”, Beginning Address to “0x800” and Container Length to “0x1B0EC”. Finally click Write Memory button,SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
9. GREEN circle will be displayed if the download succeeded.
10. Now DISCONNECT the USB cable from your phone.
11. Download stock ROM for your EU set V100R001C432B111 (739 MB)
12. extract the file H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue.zip
13. Execute “FlashTool.exe” on the PC, Go to Download tab
14. click [Scatter-loading] and Select the extracted folder 'H30-U10_Firmware_V100R001C432B111_Norwegian_operatorValue' and click 'Open'.
15. Select 'MT6582_Android_scatter.txt' found in the signed ROM folder and click 'Open'.
16. The partitions info should be loaded, make sure ALL items are checked.
17. Press [Firmware Upgrade] button or 'F8' on keyboard.
18. SP FlashTool is waiting for connection, now connect your phone to computer using USB cable, WITHOUT the battery inserted.
19. SPFT has successfully established a connection with the phone, the upgrade process will begin.
20. SP FlashTool will verify the input images and begin writing to the phone EMMC once the verification succeeded.
21. Upgrade in progress, this may take a few minutes...
22. GREEN circle will be displayed if the upgrade succeeded.
23. Now DISCONNECT the USB cable from your phone.
24. Re-insert battery to your phone, press [Volume Up] + [Power] button to enter recovery.
25. Perform a 'Factory Reset/Wipe data' before booting from the rom for the first time.
Click to expand...
Click to collapse
Hello . when I connect my phone with PC to start the process my phone vibrate and windows detect it and then it vibrate again and disconnect And do this again and again so sp flash tool come with a fail . anyone know why my phone is doing this ( connect and disconnect and keep doing this until I remove USB cable )
Thanx
Hello everyone !! I recently installed the latest android 13 beta 3.3 on my Samsung Galaxy S20. I wanted to make a guide to show you the installation process. This is a GSI of android 13 ported from the google pixel 5, therefore there are a few things that don't work properly (I will list them below). If you have any questions or issues with installation please don't hesitate to ask and I'll do my best to help you !! Hope you find this guide helpful !!
Issues / Bugs
- No biometrics (No face unlock or fingerprint scannner)
- No always on display (only screen saver available)
- No auto-brightnees
- No sound on notifications
Pre-requisites
- Unlocked bootloader
- TWRP Recovery
YouTube Step by Step Tutorial
Download Installation Files:
2.7 GB folder on MEGA
32 files and 5 subfolders
mega.nz
How to Install Android 13 Beta 3.3 on Samsung S20 Series
1. Turn your phone off
2. Connect your phone to your computer via USB cable
3. Press the "power" and "volume up" buttons at the same time until you see the TWRP logo
4. Once booted into TWRP, click on "Reboot", then click on "Fastboot"
5. Wait for your phone to boot into fastboot mode
6. Go to your computer and download the folder with the necessary installation files linked above.
7. Open the folder that you downloaded and look for the "Platform Tools (Name of your OS)" folder.
8. Look for the "fastboot" file and drag it into a new terminal window
9. Leave a space and type the word "devices"
10. Hit enter
11. If you see a bunch of random numbers followed by the word "fastboot" your computer has recognized your phone
12. Go back to the "Platform Tools (Name of your OS)" folder and once again, drag the "fastboot" file into the terminal
13. Leave a space and type the words "erase system"
14. Hit enter
15. When the process is finished you should see the words "finished" and "total time" in the terminal
16. One last time, drag the "fastboot" file to the terminal
17. Leave a space and type "flash system"
18. Go to the folder that you previously downloaded (the one linked above) and look for the "Pixel 13...Beta3.3.img" file
19. Drag the file over to the command window and hit enter
20. Wait for the file to be flashed (this might take a while)
21. When flashing is finished you will again see the message "finished" and "total time" in the terminal
22. Go back to your phone
23. Click on "Reboot"
24. Click on "System"
25. Wait for your phone to restart with the new ROM
ENJOY !!!!
Great Tutorial There, Did you ever fix the issues from the pixel to s20
also is there a way to find out if my bootloader is unlocked?
Thanks again
R0YB0Y said:
Great Tutorial There, Did you ever fix the issues from the pixel to s20
also is there a way to find out if my bootloader is unlocked?
Thanks again
Click to expand...
Click to collapse
Google or YouTube, cheers
@victoriam8a, this gsi image is installable by twrp, plus gapps and magisk (individual choice), I did it a few days ago my fp was working, bluetooth streaming not working and a few more things, I'm gonna give another try and also try all the work arounds to get things going on android 13, cheers