HELLO everyone, i have a big problem in my phone LG OPTIMUS L3 E400
i use KDZ UPDATER and update my phone with wrong kdz file and now My phone does not work and not allowed to go to EMERGENCY MODE
I hope you will give me the solution to back my phone and thank you guys and i will wait for the answer....
Go to CWM Mode (PRESS Vol + and Power button and Home button simultaneously ) after getting into CWM mode connect your phone to Computer then run KDZ updater. In KDZ screen (Phone Mode) select Emergency instead of Diag then load your KDZ file.
hassane159 said:
HELLO everyone, i have a big problem in my phone LG OPTIMUS L3 E400
i use KDZ UPDATER and update my phone with wrong kdz file and now My phone does not work and not allowed to go to EMERGENCY MODE
I hope you will give me the solution to back my phone and thank you guys and i will wait for the answer....
Click to expand...
Click to collapse
Try using lg mobile support tool which you may download from any google sites. Make sure you have good internet connection when using the tool.
Sent from my LG-E425 using XDA Free mobile app
How to Fix "error device not found in dload trying flash programmer" when use boardiag .
Lg g3 qualcomm 9008 when install driver then use tool boardiag fake tool say device not found in dload trying flash programmer
when you use tool fake board share in xda another tool say device not found in dload trying flash programmer. You need remove battery (of lg g2 hold power 1 minute) then connect cable again and use tool again
Sure install driver 100% wrong
With windowns 64 bit you need restart pc then click f8 choose disbable driver singturne....
Then remove battery (hold power 1 minute with lg g2) then connect cable try use tool unbrick >> sure done 100%
I will updload video error dload
Remember disbbale tool sony erricson if you have open tool in taskbar
How to fix “No response from the device. Check PMIC first and
if still boot problem, replace AP.”
Remove battery and connect again put qualcomm 9008 then use tool in topic
http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-all-variants/ Just as helping
[*]I see very topic unbrick qualcomm 9008 lg g2, lg g3 but all tool can not use.
I have full tool board ver 2.9.( only 2.9).
Link download drive.google.xxx /file/d/0B_Hol5T47S-bYjNETmVPZkdWUms/view?usp=sharing (xxx= com)
Support lg g2, lg g3 workking 100%.
Download tool, open BoardDiag and choose file tot correct model phone of you( you can download tot in xda)
See guide in pictrure : very easy.
Note
Hold power 2 minute and connect cable ( or remove battery)>>And open tool check ap, emmc test again
Then unbrick done remove cable, hold power 30 second and hold volume up connect cable phone put downloadmod >> Use lgflashtool 1.5 flash file tot again >> done.
If done pls donate a few beers paypal of my Thank you very much.
Man you saved my ass Thank you so much !1 when i get my salary ill donate to you and tell everybody to do so cuz this tool is amazing. im in download mode now ill try to flash with lg flash tool.
Thank so much man but my g3 last week unbrick qualcomm i had I submit for warranty[emoji24] [emoji24] I am very Star-crossed [emoji20]
Hello friend willcracker
Hello friend willcracker :good:
I hope all is well;
I saw this little tutorial so I want to ask for help
I have a LG G3 D855p and my phone is dead (bricked)
I can not quite understand the method you friend
not turn on my phone
I can not enter the "" Download Mode ""
VOL + Up when I connect the USB cable to the PC recognizes me as:
Qualcomm HS-USB QDLoader 9008 (COM10)
why I ask for help to revive my g3
If you help me ... .. I promise to donate something for you
you send a file "picture" attached
- - As I can get to "" Fastboot Mode "" on my phone
I hope your prompt response, please do not ignore my message :crying:
greetings from peru
You need to Disassemble Phone and Expose the TP Location
See pictrue
Expose the TP Location.
Done phone put qualcom 9008>> use tool unbrick
Remeber unplug battery connect only cable and short testpoint
Thanks for responding, but I need your help please friend
Hello willcracker I have no such tool you indicate "tool unbrick testpoint"
I could do this step with some type of cable or wire?
- If you Might tell me how to do that step with another option
leave your email. to chat google chat (Houngts) and you help me please
I'm worried because my g3 d855p not light, or anything like I said ....
await your prompt response, I hope you can help me
TOT Firmware, must match installed version?
Hey, thanks for providing this tool!
Final question, the TOT file must this match the installed version?
My situation:
Lollipop was installed, goal was to move to a custom rom (blisspop v2.3)
Rooting was successful
Install of twrp not, reboot into recovery caused the 'signature verification error'
Tried to flash the kitkat rom via the download method, failed, ...
Currently, I have the same verification error also when trying to get into download mode and have the Qualcomm HS-USB QDLoader 9008 in my device manager.
I have the LGD855AT-00-V10e-EUR-XX-JUL-08-2014-16G+0.tot file and did the first step of your procedure. Can I do the second step with this extract of kitkat even if lollipop was installed?
any feedback greatly appreciated!
Hello willcracker thanks, thanks for reply but I need your help please
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
**will commit without any error.
And haci get my phone g3 ... haci I could also help others or siblings who need help to solve any problem with the g3
- I can not enter download mode
- I can not enter recovery mode
- When I turn on my phone, get the LG logo goes about three letters at the top left, then flashes a red, blue lights ...
- The PC recognizes me as Qualcomm HS-USB QDLoader 9008 (COM10)
You could leave your email. Google to chat chat (Houngts) and help me please
*....
Waiting for your prompt response, I hope you can help me
Please do not ignore my message willcracker friend
Greetings from Peru
themusic1510 said:
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
Greetings from Peru
Click to expand...
Click to collapse
NO you need find google how do short testpoint samsung n7100 you see they guide short testpoint . Lg when short testpoint phone detect qualcomm 9008
And you use tool board diag unbrick.
???
themusic1510 said:
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
**will commit without any error.
And haci get my phone g3 ... haci I could also help others or siblings who need help to solve any problem with the g3
- I can not enter download mode
- I can not enter recovery mode
- When I turn on my phone, get the LG logo goes about three letters at the top left, then flashes a red, blue lights ...
- The PC recognizes me as Qualcomm HS-USB QDLoader 9008 (COM10)
You could leave your email. Google to chat chat (Houngts) and help me please
*....
Waiting for your prompt response, I hope you can help me
Please do not ignore my message willcracker friend
Greetings from Peru
Click to expand...
Click to collapse
I'm in the same boat! Could you please explain it a little better?
frank.devliegher said:
Hey, thanks for providing this tool!
Final question, the TOT file must this match the installed version?
My situation:
any feedback greatly appreciated!
Click to expand...
Click to collapse
You need extract file tot d855 and put phone to qualcomm 9008 and unbrick . DOne flash stock rom. Find rom 5.01 link another
Ahh now i see!
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
@willcracker
The link doesnt work !? Where can i download the BoardDiagTool?
I have a F240L and this totfile BIN_LGE980AT-00-V20g-ATT-US-APR-28-2014+0 .Can I use it?
I have tried with this file but i get the message AP Check or Check PMIC first
sourly64 said:
@willcracker
The link doesnt work !? Where can i download the BoardDiagTool?
I have a F240L and this totfile BIN_LGE980AT-00-V20g-ATT-US-APR-28-2014+0 .Can I use it?
I have tried with this file but i get the message AP Check or Check PMIC first
Click to expand...
Click to collapse
what do you mean?
The link unbrick only g2 g3 and gpro2
Phone of you G pro i not upload tool . Unsderstand.
Magnerion said:
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
Click to expand...
Click to collapse
Model Lg d851? writh
rememer ber tool suppoer only lg g3 f400s/l/k , lg d855 16gb and 32gb.
If use tool say error pcmic on tool not support (Ex: lg d851)
I up load only msm8974ac g3 msm8975ac g3 no upload
Magnerion said:
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
Click to expand...
Click to collapse
It seems won't work.I have gone through about this problem.Alway AP Check fail.QPST reported that phone had been in Sahara download mode for few seconds.A RMA fix my phone.But it cost me about 50dollars
willcracker said:
what do you mean?
The link unbrick only g2 g3 and gpro2
Phone of you G pro i not upload tool . Unsderstand.
Click to expand...
Click to collapse
Hello willcracker !
Thanks for the note,do you know the totfile is the right one ?
I get with this file ,when is extraced the message in BoardDiag Check PMIC first and if not boot Check AP
TOT Version
willcracker said:
You need extract file tot d855 and put phone to qualcomm 9008 and unbrick . DOne flash stock rom. Find rom 5.01 link another
Click to expand...
Click to collapse
I have a TOT file, but for kitkat, not Lollipop. Can I use this TOT file?
(have only a kdz file for lollipop)
Thx!
frank.devliegher said:
I have a TOT file, but for kitkat, not Lollipop. Can I use this TOT file?
(have only a kdz file for lollipop)
Thx!
Click to expand...
Click to collapse
YES you can use tot kikat unbrick .
sourly64 said:
Hello willcracker !
Thanks for the note,do you know the totfile is the right one ?
I get with this file ,when is extraced the message in BoardDiag Check PMIC first and if not boot Check AP
Click to expand...
Click to collapse
sr i have not upload hex lg gpro waitting comming soon.
Hi to all
I am wonder if there are ways to reflash the stock KDZ file since don't have fastboot, bootloader or even recovery, only black screen and a sort of com port recognized as RELINK-HS-USB like attached image.
I try with B2B program but, no support.
any solutions will be thanked, in case of fixed, will join development!
Have you tried LG Flash Tool 2014. Here is a webpage with all LG Leon 4G LTE firmware: http://lg-phone-firmware.com/index.php?id_mod=171
Here is a guide on how to download allow) for your phone (not recommended because your version may not be supported): http://forum.xda-developers.com/leon/how-to/how-to-update-lg-leon-h340n-to-android-t3393648
Here is a guide on how to install the original firmware for your phone(lollipop): http://forum.xda-developers.com/leon/how-to/helpful-guide-to-stock-t3211208
If you have any questions ask me, if you want, I hope I helped you
Nickblorck said:
Have you tried LG Flash Tool 2014. Here is a webpage with all LG Leon 4G LTE firmware: http://lg-phone-firmware.com/index.php?id_mod=171
Here is a guide on how to download allow) for your phone (not recommended because your version may not be supported): http://forum.xda-developers.com/leon/how-to/how-to-update-lg-leon-h340n-to-android-t3393648
Here is a guide on how to install the original firmware for your phone(lollipop): http://forum.xda-developers.com/leon/how-to/helpful-guide-to-stock-t3211208
If you have any questions ask me, if you want, I hope I helped you
Click to expand...
Click to collapse
i just try it, it's not working, the problem is showing the usb device, connected as port com, when I click on Read Phone Information, didn't work. thanks for the answer by the way
haky 86 said:
i just try it, it's not working, the problem is showing the usb device, connected as port com, when I click on Read Phone Information, didn't work. thanks for the answer by the way
Click to expand...
Click to collapse
have you changed the phone com port to 20 ???
Into lg flash tool i only connected my lg leon via usb and it automatically entered in download mode
Hi all,
Recently had some trouble where I flashed a H870 firmware onto my G600L LG G6. After hours of frustration and effort, I finally found the solution.
1. Put LG G6 into Download Mode (Hold Up Button when powered off, then plug in USB cable)
2. Download and Run LG Bridge
3. Go to software update - the software will detect the correct model and download the correct firmware file and install it
JD6750 said:
Hi all,
Recently had some trouble where I flashed a H870 firmware onto my G600L LG G6. After hours of frustration and effort, I finally found the solution.
1. Put LG G6 into Download Mode (Hold Up Button when powered off, then plug in USB cable)
2. Download and Run LG Bridge
3. Go to software update - the software will detect the correct model and download the correct firmware file and install it
Click to expand...
Click to collapse
Can I up the rom H873 for G600LP? And can fix by your way?
Well, this is a standard "fix"...
Everyone should know how to do that before even flash anything. Nothing new, but is nice to see that you have saved a G6...
Do you know how to solve that no sound bug in lg g6 g600l....
JD6750 said:
Hi all,
Recently had some trouble where I flashed a H870 firmware onto my G600L LG G6. After hours of frustration and effort, I finally found the solution.
1. Put LG G6 into Download Mode (Hold Up Button when powered off, then plug in USB cable)
2. Download and Run LG Bridge
3. Go to software update - the software will detect the correct model and download the correct firmware file and install it
Click to expand...
Click to collapse
Hy sir my lgg6 g600l running on oreo had some issues it restarts and go to ded silent and after spending some time with it it got fixed after the restart. I dont kow what the issue is not using any app at all. it does even after factory reset. any help would be appriciated. also i want root access .........
lg g6 g600l
hello team of experts i have lg g6 g600l which is running android 8 orio i ried to upgrade to 9pie on lgup but i did a mistake of did not enter my phone in download mode thats why the upgrade procces is not succesfull and now i am facing an error on lg up
0x81000302, please use latest DLL LAF Protocol version is not match DLL=150423472 Device=201969696. so what to do now to get back my phone
ab63 said:
hello team of experts i have lg g6 g600l which is running android 8 orio i ried to upgrade to 9pie on lgup but i did a mistake of did not enter my phone in download mode thats why the upgrade procces is not succesfull and now i am facing an error on lg up
0x81000302, please use latest DLL LAF Protocol version is not match DLL=150423472 Device=201969696. so what to do now to get back my phone
Click to expand...
Click to collapse
You need to find correct DLL file. Search xda forum or google
is some one have the right DLL files for lg g6 600l
Please Help, my G6 not detected in Device manager in Download mode i have installed all necessary drivers but not detected. thanks.
charledave said:
Please Help, my G6 not detected in Device manager in Download mode i have installed all necessary drivers but not detected. thanks.
Click to expand...
Click to collapse
make sure u use a good cable and also make sure you have the latest google usb drivers from android studio
Download lgup dll for g8 and lg up. New protocols inside of dll.
hi
I am using a LG G6 (software version H87310h) which is now on android 7.0 . when trying to upgrade through update center in setting it shows you are using the latest software version for current OS. what can I do to upgrade on 8.0
connect it to PC and use LG Bridge to see if they are avaiable there, install USB LG drivers first and after LG Bridge...
if they dont say nothing about update, then you need to go ahead and use Uppercut and download KDZ for your device and flash manually.
sun_is_shinning said:
connect it to PC and use LG Bridge to see if they are avaiable there, install USB LG drivers first and after LG Bridge...
if they dont say nothing about update, then you need to go ahead and use Uppercut and download KDZ for your device and flash manually.
Click to expand...
Click to collapse
Thanks for reply. I have already tried the LG bridge and says busy try latter. Can you please say how to get the proper KDZ. TIA
Firmware
https://lg-firmwares.com/lg-h873-firmwares/#tab=firmwares
use the link above find your provider use LG Up