How To install the Latest Stable Firmware of Lenovo k3 note Model K50-T5System Version: K50-T5_USR_ST1614_5.294.1_1604011150_mp1V2.39_CN
Fit models: Le lemon k3 note (K50-T5)
All necessary files can be found here ## Google drive link
Please take note that this is the Original Stock Firmware for the Model K50-T5 with Chinese/English support only and also is not Coming with Gapps Pre-installedChangelog##
Code:
[B][CENTER]This ROM is based on the official 1613 vibe3.1 Android 6.0 stable version
The problem has been fixed or changed (compared with the previous software has been released shall indicate whether there is a large Android version upgrade):
1, only charging mode plug USB, the computer can read the phone memory problem
2. Connect the AP to WEP encryption in WLAN scanning interface will continue to appear WLAN automatically shut down, open issues
3, switch the phone to the default external memory storage, OTA upgrade failure
4, the upgrade version of MR1 to stop running when M Bluetooth Sharing[/CENTER][/B]
>>Now Before you doing anything it's recommended to Backup your contacts and important data into your memory card or your laptop or your PC and Your Phone must have least 50% of battery <<Step 1. Extract the Downloaded files on your Laptop/Pc
Step 2.Install LenovoUsbDriver_v1.1.13 On your Pc and after the Instalation Restart your Laptop/PC
Step 3.If u allready did a backup of your important Data Power Off your Device
Step 4.Run the Sp flash tool(Its inside the Zip file with the Rom that u downloaded)
Step 5. Now navigate to Option/Download/General setting/DL DL All with checksum Tab and check Usb Checksum and EMMC checksum like in the picture down bellow and after setting that up click on X
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Step 6.Now from "Download" Tab click on "Scatter-Loading" and Navigate to the Scatter-Loading file(it should be like this path Your PC\K50-T5_USR_ST1614_5.294.1_1604011150_mp1V2.39_CN\target_bin\MT6752_Android_scatter)see picture bellow
Step 7.Once you Hit Open on the MT6752_Android_scatter a Procesing window will pop up(see picture bellow) Loading the necessary files for Flashing(its about 30sec-1min sec depending on your PC configuration)
Step 8. Now Click On Download Tab and Set Firmware Upgrade
Step 9. Now Connect your Phone(Turned Off) To the Pc/Laptop using Usb cable and wait about 10-15 for the Flashing Process
Step 10. Once the Flashing Process is completed a Green window will Pop Up
Step 11.Close the SP flash Tool and disconnect your phone from the Pc/Laptop
Step 12. Turn on Your Phone and wait about 10 mins for the further installation
Step 13. Congrats You have the Last stable K50-T5_USR_ST1614_5.294.1_1604011150_mp1V2.39_CN version installed
About Installing custom recovery on K3 Note using SP Flash Tool Follow This COMPLETE TUTORIALThanks To @stone_henge
ALSO FOLLOW THIS COMPLETE TUTORIALHow to Root and Flash Gapps on Lenovo K3 Note Official Stock Vibeui 3.1 1614 St Android 6.0
If you found his Tutorial guide useful you can Click the Thanks! buttonMany thanks to everyone of the Lenovo K3 Note Index Thread especially @hackerpower @stone_henge @911-Future_Maker
Original source :club.lenovo.com.cn
Finally!!! I'm looking for a tutorial like this for forever!! Thank you so much!! Just a quick question. Will this rom work in Greece?? And second now I'm chinese vibeui on Android 5.1. Can I install this rom?
Sent from my Lenovo K50-t5 using XDA-Developers mobile app
Grigoris0r20r said:
Finally!!! I'm looking for a tutorial like this for forever!! Thank you so much!! Just a quick question. Will this rom work in Greece?? And second now I'm chinese vibeui on Android 5.1. Can I install this rom?
Sent from my Lenovo K50-t5 using XDA-Developers mobile app
Click to expand...
Click to collapse
Yes this Rom can work in Greece just follow everything in the Tutorial, and this is the Official Cn/En version of the Rom. If you want Multilanguage(and thats the other Model K50A40 ROW but nevermind they are for the same phone) Follow this Post Tutorial How to install Latest ROW S422/S424 VIA SP FLASH TOOL
Really?? And the multilingual will also work in Greece right?? Oh does Google play is pre-installed in the multilingual rom or do I have to flash it?
Sent from my Lenovo K50-t5 using XDA-Developers mobile app
Grigoris0r20r said:
Really?? And the multilingual will also work in Greece right?? Oh does Google play is pre-installed in the multilingual rom or do I have to flash it?
Sent from my Lenovo K50-t5 using XDA-Developers mobile app
Click to expand...
Click to collapse
The K50A40 comes with Gapps preinstalled is multilanguage and have Vr mode feauture.
perfect!!! thank you so so much for your time and for helping me!! amazing post!! thank you again for all your help!
consulta
a query, I have updated with android Marshmallow version 6.0, but does not run any service I google my question is , if I change the roma this may use the services of google ? many thanks
una consulta, yo tengo actualizado con la version Marshmallow android 6.0, pero no me corre ningun servicio de google, mi pregunta es, si cambio la roma a esta se podra utilizar los servicios de google? muchisimas gracias
panxosk8 said:
a query, I have updated with android Marshmallow version 6.0, but does not run any service I google my question is , if I change the roma this may use the services of google ? many thanks
una consulta, yo tengo actualizado con la version Marshmallow android 6.0, pero no me corre ningun servicio de google, mi pregunta es, si cambio la roma a esta se podra utilizar los servicios de google? muchisimas gracias
Click to expand...
Click to collapse
Follow this http://forum.xda-developers.com/k3-note/general/lenovo-k50-t5-vibeui-3-1-1614-st-t3360567
Nice tutorial mate! Keep it up. :highfive:
911-Future_Maker said:
Nice tutorial mate! Keep it up. :highfive:
Click to expand...
Click to collapse
Thanks mate i Did this because of the Repeated questions/Posts Of The new Users that are lazy to do a simple search through the thread search Option You know what i Mean
Btw This Video is Devoted for all of Them
You are a Noob on XDA-Developers
Gracias
emptywordsss said:
Follow this http://forum.xda-developers.com/k3-note/general/lenovo-k50-t5-vibeui-3-1-1614-st-t3360567
Click to expand...
Click to collapse
Muchas gracias amigo _
google play services issues ?
this looks great. does my phone have to be rooted ? also if i do this will loading google play services and play store run without stopping. thanx
wriggles72 said:
this looks great. does my phone have to be rooted ? also if i do this will loading google play services and play store run without stopping. thanx
Click to expand...
Click to collapse
You dont need to be rooted and this is also excellent example if your phone get Bricked,stucked in bootloop or something else ...Also note that k50-T5 isn't coming with Gapps pre-installed you need to do that manually (see for more info in the Tutorial section) and have only chinese/english support
Hello! Any idea how to root the new s427 row rom?? Or I can use the root method from the s424?
Sent from my Lenovo K50a40 using XDA-Developers mobile app
Grigoris0r20r said:
Hello! Any idea how to root the new s427 row rom?? Or I can use the root method from the s424?
Sent from my Lenovo K50a40 using XDA-Developers mobile app
Click to expand...
Click to collapse
Ofcourse mate Download and flash S427 patched boot and after that flashSuperSU-v2.74-PRO and you are good to go :fingers-crossed:
emptywordsss said:
Ofcourse mate Download and flash S427 patched boot and after that flashSuperSU-v2.74-PRO and you are good to go :fingers-crossed:
Click to expand...
Click to collapse
And I follow the steps from s424 root method right? Thank you so much for your quick reply!
Sent from my Lenovo K50a40 using XDA-Developers mobile app
Grigoris0r20r said:
And I follow the steps from s424 root method right? Thank you so much for your quick reply
Click to expand...
Click to collapse
No problem at all mate and Yes the steps are the same like the previous update.
emptywordsss said:
No problem at all mate and Yes the steps are the same like the previous update.
Click to expand...
Click to collapse
for rooting the previous version i have used this method. http://forum.xda-developers.com/k3-note/general/sp-flash-tool-tutorial-to-install-twrp-t3346041
but there i had a recovery image that i flashed through SP flash tool. Now i have a boot image. how i flash this? via flash tools again? or with stock recovery? if you can give me a small tutorial it would be really apreciated. sorry for all those questions.
Grigoris0r20r said:
for rooting the previous version i have used this method. http://forum.xda-developers.com/k3-note/general/sp-flash-tool-tutorial-to-install-twrp-t3346041
but there i had a recovery image that i flashed through SP flash tool. Now i have a boot image. how i flash this? via flash tools again? or with stock recovery? if you can give me a small tutorial it would be really apreciated. sorry for all those questions.
Click to expand...
Click to collapse
First of all flash TWRP from the link you posted and than flash the files through TWRP recovery.
Oh man! You Are The Man!
My Lollipop went into any endless loop about Something Unexpectedly Stopped...
Decided to upgrade to Marshmallow. Then found your fantastic tutorial. Follow it and voila, Android 6!
Keep up the good work!
---------- Post added at 08:19 PM ---------- Previous post was at 07:28 PM ----------
One quick question: Can I take OTA updates? There's one waiting...
Thanks again.
Related
Modding Lenovo K3 Note
I anticipate that I will, nor the forum will take responsibility 'of malfunctions and \ or damage!
Part One - CMW Install and Root command line
In this thread, I'll describe a simple, fast, and definitely safer than SPFTools.
SPFTools VCOM working on ports that are not always recognized, sometimes give problems also installing special drivers, they are almost always a problem for Windows because of the signatures on the driver.
Closed this little digression for information, we start with the drivers:
Driver Lenovo K3 Note + PDAnet+:
https://mega.co.nz/#!O4lmBaZa!jCUk1z0BB6wsBgP1P3e5BdoJQtBY_xi6TXuwcBOCv5k
Click to expand...
Click to collapse
Install all drivers Lenovo inside. Once you finished enable the USB debugging and wait for Windows to complete its configuration.
When completed restart the PC and install the utility on the device:
PdaNet:
https://play.google.com/store/apps/details?id=com.pdanet&hl=it
Click to expand...
Click to collapse
Be sure to restart to have all the drivers installed correctly and stay in Debug USB.
Without this included in your terminal this .zip file to obtain permits Root later:
SuperSU:
https://mega.co.nz/#!b8tSiYZJ!yr3okwkxmoR8NqSN10PCEtxsLl25aZ3VUSALqTKszsM
Click to expand...
Click to collapse
Now download this Minimal ADB (with Recovery K3 notes included) from here:
Minimal ADB & Fastboot + K3 Note Recovery (CWM):
https://mega.co.nz/#!rs0lHZrI!hE3Ux99skP-q3RYsgb9KNwX2Dnji192uU0KJB3iQNdo
Click to expand...
Click to collapse
Now comes the fun part!
Unzip the zip file and open the file py_cmd.exe and quietly run these commands:
Code:
adb devices
To ensure that the PC recognizes the device, and if it should be unauthorized make sure that USB debugging is enabled.
Code:
adb reboot bootloader
This command will reboot the phone on a black screen, going in fastboot .
Code:
fastboot devices
This command will confirm the above.
Code:
fastboot flash recovery recovery.img
This command will install the much sought CWM, but it is not over yet!
Code:
fastboot reboot
This command will restart the device.
Perfect! now to get root permissions, there will be that off the device, wait a few seconds and turn it on using this key combination:
VOLUME UP - VOLUME DOWN - POWER
Click to expand...
Click to collapse
Wait until the CWM is not playing, choose obviously the English language.
Subsequently searching
Code:
install zip
... and subsequently ...
Code:
choose zip from /sdcard
... looking for that zip file SuperUser inserted at the beginning.
Et voila! The device is unlocked and ready to receive new rom and functionality!
Part Two - Install new ROM from SPFTools CWM does not work when
Many with the above guide you tried to change the finding in eom stuck.
With this procedure you can go back, but before we move forward I want to give you a few details regarding the update of the rom:
*- The rom mounted on chinese devices with Play Service support and multilanguage already moddate the seller.
*- Given the above, download a rom 'official' (see NeedRom) carrying the phone in its native state.
*- If you need to download the latest versions from the site VibeUI not download the latest available, sometimes the downgrade is not possible (personal experience).
Let's start!
First, before you go ahead to make sure you have followed the guidance post 100% in the first part of the thread.
Follow the link:
SPFTools V5:
https://mega.co.nz/#!G0sVBK5A!M9DovhVgx_aCdXpySq0zmkKvrPbAFePtJgZRXyjtG7w
Click to expand...
Click to collapse
Now unpack everything and put it in a folder convenient for you.
I post the link of a rom in case I tried to see if this will work, even to you. To me it is working well.
In the third part if this rom works almost everyone will get all roms that I find around and decide what to do and what to do.
Rom 1949Deal:
https://www.dropbox.com/s/zep53n1j214ri45/lenovo k3 note rom.rar?dl=0
Password: 1949dealjoy
Click to expand...
Click to collapse
Once downloaded, extract directory in a readily available and open flash_tool.exe .
Before we go on, first remove the battery and attach only the USB cable, then set the SPFTools this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Set in this way the program.
In step [1] look for the previously extracted folder and locate the file.
Give the program a few seconds to load the rom, and after leaving it in Download Only Click Download .
Obviously nothing will happen, to make sure that going forward, you can simply insert the battery and wait for the completion of the transaction.
Reinstall the back cover and turn on the device. Give it about 8/10 minutes for the first startup.
Et voila! We are again ready to modding this Lenovo K3 notes!
Part Three - Collection ROM
In update
You will not find in this type of tour guides, as is the link is driving are my own work, so excluding the Play app store are my property. If you have any problem with the link, do not hesitate to ask.
If you have been useful, it is needless to say that it is a thanks is appreciated!
PS: SORRY FOR MY BAD ENGLISH!
Works like a charm. Thanks
will get my lenovo in a week and will use this guide, Thanks!
just one question, when installing the driver's is phono connected to pc? and is it connected with battery inside it?
kangel said:
Modding Lenovo K3 Note
I anticipate that I will, nor the forum will take responsibility 'of malfunctions and \ or damage!
In this thread, I'll describe a simple, fast, and definitely safer than SPFTools.
SPFTools VCOM working on ports that are not always recognized, sometimes give problems also installing special drivers, they are almost always a problem for Windows because of the signatures on the driver.
Closed this little digression for information, we start with the drivers:
Install all drivers Lenovo inside. Once you finished enable the USB debugging and wait for Windows to complete its configuration.
When completed restart the PC and install the utility on the device:
Be sure to restart to have all the drivers installed correctly and stay in Debug USB.
Without this included in your terminal this .zip file to obtain permits Root later:
Now download this Minimal ADB (with Recovery K3 notes included) from here:
Now comes the fun part!
Unzip the zip file and open the file py_cmd.exe and quietly run these commands:
Code:
adb devices
To ensure that the PC recognizes the device, and if it should be unauthorized make sure that USB debugging is enabled.
Code:
adb reboot bootloader
This command will reboot the phone on a black screen, going in fastboot .
Code:
fastboot devices
This command will confirm the above.
Code:
fastboot flash recovery recovery.img
This command will install the much sought CWM, but it is not over yet!
Code:
fastboot reboot
This command will restart the device.
Perfect! now to get root permissions, there will be that off the device, wait a few seconds and turn it on using this key combination:
Wait until the CWM is not playing, choose obviously the English language.
Subsequently searching
Code:
install zip
... and subsequently ...
Code:
choose zip from /sdcard
... looking for that zip file SuperUser inserted at the beginning.
Et voila! The device is unlocked and ready to receive new rom and functionality!
You will not find in this type of tour guides, as is the link is driving are my own work, so excluding the Play app store are my property. If you have any problem with the link, do not hesitate to ask.
If you have been useful, it is needless to say that it is a thanks is appreciated!
PS: SORRY FOR MY BAD ENGLISH!
Click to expand...
Click to collapse
itzikd1 said:
will get my lenovo in a week and will use this guide, Thanks!
just one question, when installing the driver's is phono connected to pc? and is it connected with battery inside it?
Click to expand...
Click to collapse
Yes, the battery must be installed
thanks, rooted easly, took 5 mintues!
@kangel,thank you very much for this initiative. great contributions. You can visit the thread in Spanish to complement. Thanks again and I'll be here
Better add a custom ROM for Lenovo K3 note in the thread has official Roms of lenovo k3 note are useless bcuz FDD 4G and VPN are not supported in k3 notes official ROM. It would be better if some one finds and updates the thread with k3 notes custom roms available :good:
asif3366 said:
Better add a custom ROM for Lenovo K3 note in the thread has official Roms of lenovo k3 note are useless bcuz FDD 4G and VPN are not supported in k3 notes official ROM. It would be better if some one finds and updates the thread with k3 notes custom roms available :good:
Click to expand...
Click to collapse
Do you have it and know that FDD LTE is not supported? Sounds unlikely as China Unicom has FDD LTE in addition to TDD LTE (and the phone supports China Unicom).
Is there any ROM supporting dual SIMs?
Thanks.
sam10000 said:
Is there any ROM supporting dual SIMs?
Thanks.
Click to expand...
Click to collapse
Every ROM of k3 note official or custom ROM supports dual sim
---------- Post added at 09:45 AM ---------- Previous post was at 09:32 AM ----------
_mfm_ said:
Do you have it and know that FDD LTE is not supported? Sounds unlikely as China Unicom has FDD LTE in addition to TDD LTE (and the phone supports China Unicom).
Click to expand...
Click to collapse
Yes I have lenovo k3 note since few weeks but still I am not able to make FDD 4g work in my K3 note but yes I have fixed the VPN problem with a custom ROM but still 4g is not working in my K3 note.
Hi
Anyone knows where to get the STOCK rom (VIBEUI_V2.5_1512_5.495.1_ST_K50-T5) ?
And also from above CWM , can we flash below DEV rom ? Took from here (http://www.vibeui.com/vibeui/rom?key=k3 note#version-slip1)
VIBEUI_V2.5_1520_7.128.1_DEV_K50-T5
Or need to use FlashTool ?
asif3366 said:
Every ROM of k3 note official or custom ROM supports dual sim
---------- Post added at 09:45 AM ---------- Previous post was at 09:32 AM ----------
Yes I have lenovo k3 note since few weeks but still I am not able to make FDD 4g work in my K3 note but yes I have fixed the VPN problem with a custom ROM but still 4g is not working in my K3 note.
Click to expand...
Click to collapse
What mobile operator do you use?
BTW, Can you check if RDS is supported in the FM Radio app?
Pls add in 1st page for easy reference...
FeyoMx said:
@kangel,thank you very much for this initiative. great contributions. You can visit the thread in Spanish to complement. Thanks again and I'll be here
Click to expand...
Click to collapse
Hi FeyoMx,
Can you please provide us a link to download the fixed CWM recovery ?
the actual recovery (CWM or TWRP) can not do a correct restore, the phone will only reboot to recovery after a restore
Thank you.
dreambo said:
Hi FeyoMx,
Can you please provide us a link to download the fixed CWM recovery ?
the actual recovery (CWM or TWRP) can not do a correct restore, the phone will only reboot to recovery after a restore
Thank you.
Click to expand...
Click to collapse
Hi, here it is. This restores good backups
FeyoMx said:
Hi, here it is. This restores good backups
Click to expand...
Click to collapse
Thank you
I have already see that link, but I do not understand Spanish and in the google translated version, I can not have the download link :
We must follow the link of the china forum, or we have to be registered to see the link in the thread ?
dreambo said:
Thank you
I have already see that link, but I do not understand Spanish and in the google translated version, I can not have the download link :
We must follow the link of the china forum, or we have to be registered to see the link in the thread ?
Click to expand...
Click to collapse
Sorry https://drive.google.com/file/d/0BwmBEcCNY-yhSUVEY1BITnF5Zjg/view?usp=sharing
the instructions for use if you understand?
FeyoMx said:
Sorry https://drive.google.com/file/d/0BwmBEcCNY-yhSUVEY1BITnF5Zjg/view?usp=sharing
the instructions for use if you understand?
Click to expand...
Click to collapse
Thank you very match
No worry for instructions, the most important file is recovery.img and we can flash it using different manners.
I will test it this night at home.
thank you again.
[REQ] SafeCenter
Dear Colleagues,
I have Lenovo Vibe Z2. It has got recently the Lollipop upgrade that works quite well. But Lenovo did not include the SafeCecter app into the upgrade and the old one, extracted from the 4.4 ROM, isn't compatible with the new ROM, it even cannot be installed.
So, my request: would someone be so kind and extract the SafeCecter app from the K3 Note firmware for me? Since the K3 also has Lollipop I hope that your SafeCecter would serve well on my Z2 too.
Thanks a lot in advance!
ctibor said:
Dear Colleagues,
I have Lenovo Vibe Z2. It has got recently the Lollipop upgrade that works quite well. But Lenovo did not include the SafeCecter app into the upgrade and the old one, extracted from the 4.4 ROM, isn't compatible with the new ROM, it even cannot be installed.
So, my request: would someone be so kind and extract the SafeCecter app from the K3 Note firmware for me? Since the K3 also has Lollipop I hope that your SafeCecter would serve well on my Z2 too.
Thanks a lot in advance!
Click to expand...
Click to collapse
I hope you work. place on /System/priv-app and set permissions. greetings.
Hi Guys
First of all I will request to moderator of this forum to create ZTE 9 development section and put this post there.
Official Indian Rom for Nubia Z9 Mini (in any case if you don't like any ROM you can always switch to this one using TWRP )
**Official Nubia Z9 Mini Indian Version ROM Direct Download**
So guys after a lot of googling finally i was able to find a custom recovery and root tool for ZTE Nubia Z9 Mini and maked it to work for me and sharing same with you guys who want to root their Z9 mini and wanna taste some custom rom over Nubia UI here you can download One Click Root & custom Recovery (TWRP English Version) Tool for ZTE Nubia Z9 Mini.
just download the tool from Given link and Fallow instruction and you will be able to successfully able to root your phone and can install custom recovery based on TWRP
1-Download the File from Given Link and Extract it in your Desktop
2 you can see Given File list in Extracted Folder :-
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3- Enable USB Debugging On your Phone and connect it to your PC ( for USB debugging fallow step below in image )
4- Now click and run ThemePush.bat from extracted folder and you can see Below screen with option .
Now just Choose a no given in toolbox to perform the task . just input no and hit enter
this tool has default recovery too if sometime you want to gonna back to Nubia deafult recovery just install original Recovery.
here Is TWRP recovery screenshot its themed version so don't get confused .
Tool Download Link
Click to expand...
Click to collapse
Click Here To download One Click Tool
you can also checkout some ROMS i have found Working below :-
i would like to thnx to modify the recovery to work with nubia z9 mini (Cuoco92 an italian developer ) and Translator of tool (travelbug)
**Note :- for upgrading your nubia Rom to V3.50 and Higher you have to install new TWRP Recovery Version 2.8.7.0 **
*Flashable TWRP V 2.8.7.0 With Advance Modes*
*** Nubia Z9 Mini Rom V 3.87 for International carrier support works for Indian Networks !! ***
Link :-Nubia ROM with all feature working and supports Indian Network
thanks to @Cuoco92 for sharing this wonderful multi language Rom
thanks for this tool
...its usefull
---------- Post added at 12:30 PM ---------- Previous post was at 12:29 PM ----------
please give me indian version stock firmware link.......my internet is not work on chines roms
vijay2 said:
thanks for this tool
...its usefull
---------- Post added at 12:30 PM ---------- Previous post was at 12:29 PM ----------
please give me indian version stock firmware link.......my internet is not work on chines roms
Click to expand...
Click to collapse
hi Vijay
i dont have official indian ROM yet but i created a nandroid backup of my rom which is Indian and Pre rooted u can use "Nandroid Manager * ROOT" software from play store to restore this nandroid backup and resolve ur network issue problem and do not forget to make backup of ur data as your phone will be restored to factory defaults link updated in post check and download
dear hydrnoide,,,thanks for reply.....your nandroid back gives me errror....when am goes to archieve......he gives me error ....archieve no 1,2,5.........check your archive please...
vijay2 said:
dear hydrnoide,,,thanks for reply.....your nandroid back gives me errror....when am goes to archieve......he gives me error ....archieve no 1,2,5.........check your archive please...
Click to expand...
Click to collapse
uploaded again buddy download and check
yeah..its 100% perfect...thanks
keeps saying fastboot is not recognized???
---------- Post added at 12:26 PM ---------- Previous post was at 12:19 PM ----------
phone has to be in PTP usb mode not MTP usb mode and double click on themepush and then hit run don't run as administrator.
Has anyone managed to get Google apps installed on the CM 12.1 ROM for the Z9 Mini? If so, how?
edit: nm, figured it out, been a little while since I've used CM. You need to download the GApps zip from CM, make sure it's the 64bit version, than install it via Recovery.
Vijay. Have done exactly what you suggested. Changed USB debugging to PTP from MTP etc... Still shows error fastboot not recognized when I'm on #2. . Any thoughts or suggestions?
---------- Post added at 03:11 AM ---------- Previous post was at 03:07 AM ----------
Appreciate some suggestions as I have done what you suggested.. PTP I instead of MTP etc...still get fast boot not recognized when I go to step 2. Gotta be missing something?
I see that on your download link for roms is a 12.1 cm rom, is that one working? I can't find anything about it on the Internet.
Sent from my NX511J using XDA Free mobile app
murdocknl said:
I see that on your download link for roms is a 12.1 cm rom, is that one working? I can't find anything about it on the Internet.
Click to expand...
Click to collapse
It's unofficial, comes from a Chinese forum. It does mostly work, however I've now removed it because it disables the backlighting for the back and menu capacitive keys and you lose access to a few features from the stock ROM, like the excellent camera app.
Any fully working Custom ROM?
I have tried many custom ROMS like CM 12.1, MIUI etc and finally have reverted to the latest factory V1.19(Chinese version) as the breathing lights and Nubia camera functions do not work on the custom ROM's . But even on the factory based ROM I have faced one major issue. I am using BSNL and iDEA sims. I am not able to enable 3G on my BSNL sim and the only combo where I can use 3G is when i use iDEA as the first sim. the 3G/2G changing does not seem to work fluently...It stubbornly stays on 2G and sometimes even when 3G is enabled on BSNL, I do not see any data even if I try to turn the data slider on. Has any one come across such issues? Everything started after I rooted my phone and tried to install custom ROM's. Now even when i flash the factory ROM these weird issues remain...
yeah cm has camera issue video recording does not work
You also have to checkmark the box on your phone! when USB debugging is turned on.
Go into setting about phone. tap build number like 7 times. then press back once the click more then you should see a new menu called developer options. click on the and scroll to usb debugging then once the slider is blue a window should pop up on your phone tick allow all the time and that wool should now work!
or try a different USB port in computer and a different cable. Make sure drivers are installed. and phone has to be connected to computer with you being able to access its root folder first.
---------- Post added at 11:41 AM ---------- Previous post was at 11:40 AM ----------
52smitty said:
Vijay. Have done exactly what you suggested. Changed USB debugging to PTP from MTP etc... Still shows error fastboot not recognized when I'm on #2. . Any thoughts or suggestions?
---------- Post added at 03:11 AM ---------- Previous post was at 03:07 AM ----------
Appreciate some suggestions as I have done what you suggested.. PTP I instead of MTP etc...still get fast boot not recognized when I go to step 2. Gotta be missing something?
Click to expand...
Click to collapse
try a different USB port in computer and a different cable. Make sure drivers are installed. and phone has to be connected to computer with you being able to access its root folder first.
Hello ,
Does the Indian Rom support multilanguage or just English ?
Thanks .
This will work fine with the new official v3.10 rom? Which gapps package do I need to flash?
realy good job !!!
it's works very well
thank you very mouch bro .
@hydronoide Can i use this for Nubia Z9 NX508J?
Sent from my SM-A500H using Tapatalk
BinMgen said:
@hydronoide Can i use this for Nubia Z9 NX508J?
Sent from my SM-A500H using Tapatalk
Click to expand...
Click to collapse
i have no idea about this Bin may be u can give a try to this but before doing anything make a backup of your device.
BinMgen said:
@hydronoide Can i use this for Nubia Z9 NX508J?
Sent from my SM-A500H using Tapatalk
Click to expand...
Click to collapse
Hi,
unfortunately not!
I'm searching to custom recovery for NX508J..but for now nothing that works good!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
specs here : http://www.meizu.com/en/products/m2/spec.html
FAQs:
Will this phone work in my country? http://www.willmyphonework.net/
ROMs:
Official ROM: http://www.flyme.cn/firmwarelist-19.html
Instructions:
Download the newest version from http://www.flyme.cn/firmwarelist-19.html
You now have the update.zip, now connect your Meizu with your PC
Copy the update.zip to the main folder (internal) of your Meizu
Optional: you might want to do a factory reset, otherwise your gonna flash over your old install. To do a factory reset, go to settings -> about phone -> memory/storage
Reboot and press Vol+ & Power at the same time.
Choose System upgrade and press Start
Wait for it to install, you're done!
Root
How do I root my device?
Settings > Accounts > My Flyme > "YOURUSERNAME" > System privileges
How do I unroot my device?
Simply flash the firmware again. Clearing data is not required.
Post here for all your questions, reviews, unboxing, news and discussions on this highly anticipated phone from Meizu.
update 23-11-15
I version is here :
https://drive.google.com/file/d/0B9U0tm7Dgqjld0xQNHcyeEhmNEk/view
and the way is here:
https://translate.google.com/transl...p?route=pavblog/blog&id=18&edit-text=&act=url
xposed is here :
https://meizufans.eu/forum/topic/37...rk-on-4-5-4-1a-firmware-working-on-m2note-too
tested and work on 4.5.4.1A & 4.5.4i firmware
update 01-06-16
Flyme OS 5.1.6.0 Global is here :
http://www.flymeos.com/firmwarelist?modelId=18&type=1
Root for Flyme OS 5.1.6.0 Global is here :
https://forum.meizufans.eu/topic/5493/how-to-root-flyme-os-5-1-6-0g
update 12-08-16
Flyme OS 5.1.8.0 Global is here :
http://www.flymeos.com/firmwarelist?modelId=18&type=1
update 6-09-16
Flyme OS 5.1.9.0 Global is here :
http://www.flymeos.com/firmwarelist?modelId=18&type=1
update 29-09-16
Flyme OS Flyme 5.1.10.0 Global is here :
http://www.flymeos.com/firmwarelist?modelId=18&type=1
update 03-10-16
Flyme OS Flyme 5.1.11.0 Global is here :
http://www.flymeos.com/firmwarelist?modelId=18&type=1
No language
Hi
Can i flash m2 note International rom on my m2 mini? I need language from International version and there is no such for m2 mini
No you can't. Use the morelocale2 so get out I version for the mini
Sent from my 1+1
The following applications can be freeze without problems occur in the operation of the device:
App Center
Basic Daydream
Browser
Cloud Account/Service
Game Center
Life
Meizu Game Frame
Messages
Print Spooler
Sina Weibo Share
System Keyboard / Wallpaper
Tips / Weather
firmware flyme
Hello.
Please can you tell me if it is possible. I have meizu m2 mini with flyme 4.5.3 C.
I want to change it to version A or I is this possible?
The link you refer firmware is of meizu charme (is this the same as meizu m2 mini?)
version A what means the letter A?
thanks
ministerbeel said:
Hello.
Please can you tell me if it is possible. I have meizu m2 mini with flyme 4.5.3 C.
I want to change it to version A or I is this possible?
The link you refer firmware is of meizu charme (is this the same as meizu m2 mini?)
version A what means the letter A?
thanks
Click to expand...
Click to collapse
yes it is possible
I version It has not been issued yet
There are 4 types of firmwares:
A = Generic
U = China Unicom
C = China Mobile
I = International
paiktaras said:
yes it is possible
I version It has not been issued yet
There are 4 types of firmwares:
A = Generic
U = China Unicom
C = China Mobile
I = International
Click to expand...
Click to collapse
Thanks a lot for your answer.
Can you tell me the diverence between the A version en the C?
I live in the netherlands wich would you prefer?
To update, can i save file in internal memory and run it on phone itself?
greetings
ministerbeel said:
Thanks a lot for your answer.
Can you tell me the diverence between the A version en the C?
I live in the netherlands wich would you prefer?
To update, can i save file in internal memory and run it on phone itself?
greetings
Click to expand...
Click to collapse
I do not know what the differences.
Logically would be minimal, better to have the A I think, is generic and and all the rest in this based....
From what store bought device ?
paiktaras said:
I do not know what the differences.
Logically would be minimal, better to have the A I think, is generic and and all the rest in this based....
From what store bought device ?
Click to expand...
Click to collapse
from Pandawil
What about freezing/removing Reader application?
Removing unwanted Apps
matheush said:
What about freezing/removing Reader application?
Click to expand...
Click to collapse
I have a C version and was able to intall a real root access with Kingo and than remove the unwanted apps with a good uninstall app.
Now I have almost non chineese signs, my battery lasts mutch longer and it feels more "my phone"
One problem to solve. I can't lock the screen. Probaly because the phonenumber isn't bound. There is no way to fill the number field with a + and my international number. So I can't get a code to bind.
Is ther somebody with the same problem?
Hey everyone. I have one strange and annoying problem:
I went running, so I turned on Endomondo and Rocket Player. I started new training and started running. After few minutes both apps stopped working(without any alerts or anything). I tried few times again with Endomondo and every time when I unlocked phone the app was like freshly started. I have no clue what to do now. Now I'm trying playing some music on rocket player - after few minutes app just stops again......
Oh, and if you shake your phone do you have a feeling that something is "clunking" inside?
I heard that the A version of rom got less crappy apps than U or C. In general if you want use this phone use version A and wait for I.
Hey guys,
got this device since yesterday and wanted to remove the chinese-bloatware. But if I deinstall them with TB, they just reappear after reboot. Isn't this possible with the last firmware (Flyme OS 4.5.3.2A)?
Thank you very much!
Hello everyone,
I did all the works in trying to root it (according to every available instruction available), and still no app (and I did try a lot) has root access. Basically, just the same as this guy:
http://forum.xda-developers.com/gen...2-note-mini-root-failed-t3217530#post63159227
Has anyone encountered any such problems? Firmware is 4.5.3.1A, phone purchased off Pandawill.
Thanks in advance!
All the best,
Mihai Toma
hghfhgfhgghfhgfghfh said:
Hello everyone,
I did all the works in trying to root it (according to every available instruction available), and still no app (and I did try a lot) has root access. Basically, just the same as this guy:
http://forum.xda-developers.com/gen...2-note-mini-root-failed-t3217530#post63159227
Has anyone encountered any such problems? Firmware is 4.5.3.1A, phone purchased off Pandawill.
Thanks in advance!
All the best,
Mihai Toma
Click to expand...
Click to collapse
first of all update the device to the last firmware 4.5.3.2A and after for this tried again to root
paiktaras said:
first of all update the device to the last firmware 4.5.3.2A and after for this tried again to root
Click to expand...
Click to collapse
Thank you, this worked. Below is a short summary, in case anybody is interested.
First did an upgrade, all the settings and apps remained as they were, and the root worked. Well, Play Store had it's issues, which could have been solved. After, did a clean upgrade, and it still worked. So I guess that's the solution. Be wary that you have to use "Google Installer" in the Meizu "App Center" to install Google Play.
BUUUUUT. Now the mobile data services won't work. I did uninstall some System applications, but I stayed within those proposed by the OP in the first posts. Does anybody know where to go to solve this?
Thanks!
All the best,
Mihai Toma
hghfhgfhgghfhgfghfh said:
Thank you, this worked. Below is a short summary, in case anybody is interested.
First did an upgrade, all the settings and apps remained as they were, and the root worked. Well, Play Store had it's issues, which could have been solved. After, did a clean upgrade, and it still worked. So I guess that's the solution. Be wary that you have to use "Google Installer" in the Meizu "App Center" to install Google Play.
BUUUUUT. Now the mobile data services won't work. I did uninstall some System applications, but I stayed within those proposed by the OP in the first posts. Does anybody know where to go to solve this?
Thanks!
All the best,
Mihai Toma
Click to expand...
Click to collapse
Aaaaaand, I made it all work out. Don't really know how - after quite a few APN settings, it finally worked. Even though I'm 99% sure I did the right settings the first time. Hell knows.
So, for any others - watch out over your APN settings after a clean install. You must use your carrier's defaults (found on their website). And maybe a bit of luck/voodoo? Dunno what I did wrong the first times.
snoK123 said:
Hey guys,
got this device since yesterday and wanted to remove the chinese-bloatware. But if I deinstall them with TB, they just reappear after reboot. Isn't this possible with the last firmware (Flyme OS 4.5.3.2A)?
Thank you very much!
Click to expand...
Click to collapse
Try to freeze them only. This works for me on my m2 note. Did not try it yet on the m2 mini
---------- Post added at 09:13 PM ---------- Previous post was at 09:10 PM ----------
I got my device with 4.5.3.2 a. it has only a limited list of languages.
Has anyone the version 4.5.3 a? please update what languages it has
try to install google services, but the google installer from app center failed when try install google services. after that "a key to install" came up and i press it, but same thing happen, always failed. even uninstall and reinstall the google installer
EDIT :
I found out that the newest version that is google installer 2.0 from App Center doesn't work well. i download the 1.4.4 it's install successfully on my m2 mini running flyme 4.5.3.2a
Since the stock 5.1.1 was released
no one here on XDA made a root for it
but Blue cat 4pda member did : D
so im just sharing his work nothing else
Link to his threadhttp://4pda.ru/forum/index.php?showtopic=695399&st=40#entry43655190
if you cant register in the Russian forum then here's the files on dropbox thanx to @falcaobr
https://www.dropbox.com/s/wjpsa77tceastir/Root_SM_G800H_DS_511_Required%20Files.zip?dl=0
Installation sequence:
1) Enter the download mode and install firmware 5.1.1 through Odin. To reboot and enter the Lollipop everything is working;
2) Again in download mode, install the modified kernel (Kernel.tar) via Odin (use AP or PDA, depending on the version of Odin) and reboot;
3) Again in download mode, install TWRP via Odin and reboot;
4) Save "BETA-SuperSU-v2.50.zip" to SDCARD (internal or external);
5) Reboot into Recovery mode (TWRP) and install "BETA-SuperSU-v2.50.zip";
6) Restart and will be with root.
Note: Those who do not allow write to the SDCARD with Lollipop 5.1.1, install the program " FolderMount" after root and run the first time he will ask to start and fix this problem
Also if you lost your SIM and WiFi after updating to 5.1.1 try this http://forum.xda-developers.com/galaxy-s5-mini/general/sim-wifi-fix-aftar-lollipop-update-t3224352
Big thanx to Blue cat and @falcaobr i just shared thir effort
And sorry for my bad English
Happy rooting : )
ITS HIGHLY RECOMMEND TO UNINSTALL KNOX AND HIS FRIENDS AFTER ROOTING SO YOU WONT HAVE ANY PROBLEMS IN THE FUTURE INCLUDING THE BOOTLOOP ISSUE THAT SOME USERS REPORTS
Thank you.
Everything mentioned is exactly what is needed and what will happen.
I followed the instructions and all good.
ashishpmb said:
Thank you.
Everything mentioned is exactly what is needed and what will happen.
I followed the instructions and all good.
Click to expand...
Click to collapse
Thank you for your feedback
Works for me too!
Gesendet von meinem SM-G800H mit Hilfe von XDA Forums
You don't need any custom kernel if you install TWRP and flash SuperSU directly! After flashing TWRP your warranty counter was tripped!
Negative! I beg to differ friend, I have tested before with the original kernel and TWRP but not working. You can only root with the same kernel modified.
Sent from my SM-G800H/DS
I rooted many many ROMs since Android 4.0 and I have never needed a custom kernel for that! And why is here a Beta version of SuperSU linked? My Note Pro 12.2 with 5.0.2 ROM needs also no custom kernel! Simple TWRP and a RELEASED SuperSu Zip!
What do you mean with "not working"? Details please.
Btw. here you can find the link for the official released version of Chainfire's SuperSU: http://download.chainfire.eu/supersu
tomatende2001 said:
I rooted many many ROMs since Android 4.0 and I have never needed a custom kernel for that! And why is here a Beta version of SuperSU linked? My Note Pro 12.2 with 5.0.2 ROM needs also no custom kernel! Simple TWRP and a RELEASED SuperSu Zip!
What do you mean with "not working"? Details please.
Btw. here you can find the link for the official released version of Chainfire's SuperSU: http://download.chainfire.eu/supersu
Click to expand...
Click to collapse
on 5.1.1 installing SU without a custom kernel will cause an infinity boot screen
i tried it on the s6 and the s5 mini
On my Note Pro 12.2 this is not a problem (with CM12.1 and Pac ROM), also on my HTC One mini 2. Did you used your Beta version or the official Release?
tomatende2001 said:
On my Note Pro 12.2 this is not a problem (with CM12.1 and Pac ROM), also on my HTC One mini 2. Did you used your Beta version or the official Release?
Click to expand...
Click to collapse
I forget to mention that only TW roms required a kernel to get a working SU
if you dont believe me go and try it yourself and you'll have an infinity boot screen : )
as for SU only 2.50 support TW 5.1.1
theres a new beta 3.10 as i remember for android 6.0
I worked over a half year with SU 2.46 on 5.1.1 (CM12.1 on my Note Pro 12.2)! What do you mean with "TW ROMs"? And no, i don't try it, because I need my warranty on my phone. I have a rooted Note Pro 12.2, thats enough and it is only rooted, because I have to change the resolution and DPI to use it with a external Full-HD monitor.
tomatende2001 said:
I worked over a half year with SU 2.46 on 5.1.1 (CM12.1 on my Note Pro 12.2)! What do you mean with "TW ROMs"? And no, i don't try it, because I need my warranty on my phone. I have a rooted Note Pro 12.2, thats enough and it is only rooted, because I have to change the resolution and DPI to use it with a external Full-HD monitor.
Click to expand...
Click to collapse
TW roms=Touchwiz=Samsung stock roms
as for cm12 it has a built in custome kernel so SU works
and calm down ._. nothing to be angry for .-.
But 2.46 works on 5.1.1! Don't use Betas if you don't know what you do and do not post it as Guide for users that not have the needed knowledge!
tomatende2001 said:
But 2.46 works on 5.1.1! Don't use Betas if you don't know what you do and do not post it as Guide for users that not have the needed knowledge!
Click to expand...
Click to collapse
its just as i said before ONLY 2.50 WORKS ON TW 5.1.1 2.46 WILL BRICK THE DEVICE IVE ALREADY TRIED IT OUT AND HAD TO RE-INSTALL THE WHOLE ROM AGAIN
CONTACT CHAINFIRE IF YOU DONT BELIEVE ME
[ENG]
Ok, so if I want to take root in S5 Mini, I need to set up a modified kernel and a recovery, right?
And if I want to go back to the original kernel and recovery, I can do this? And back to the KitKat?
Thanks for the guide!
(OBS: My English is not very good.)
[pt-br]
Ok, para eu quiser fazer root no S5 Mini preciso instalar uma kernel e uma recovery modificada certo?
Caso queira voltar para a kernel e a recovery original, eu possível fazer isso? E voltar para o Kitkat?
Obrigado!
felipebonito said:
[ENG]
Ok, so if I want to take root in S5 Mini, I need to set up a modified kernel and a recovery, right?
And if I want to go back to the original kernel and recovery, I can do this? And back to the KitKat?
Thanks for the guide!
(OBS: My English is not very good.)
[pt-br]
Ok, para eu quiser fazer root no S5 Mini preciso instalar uma kernel e uma recovery modificada certo?
Caso queira voltar para a kernel e a recovery original, eu possível fazer isso? E voltar para o Kitkat?
Obrigado!
Click to expand...
Click to collapse
yes but your warranty will gone
Good evening. Will this work on my s5 mini G800H running 4.2.2?
Sent from my SM-G800H using XDA Forums
jade12 said:
Good evening. Will this work on my s5 mini G800H running 4.2.2?
Sent from my SM-G800H using XDA Forums
Click to expand...
Click to collapse
yes you can the same steps but without installing the kernel
but i suggest you to use this thread http://forum.xda-developers.com/gal...pment/recovery-qualcomm-twrp-2-8-7-0-t3245256 its better for a kitkat user
also if its too complicated for you i can post a thread with even more easy way of rooting
Thank you very much. It worked!!!
becube said:
Thank you very much. It worked!!!
Click to expand...
Click to collapse
Glad to hear that
When compiling ROMs it is advised to use H324 source because it's not so broken and is universal for single/dual sim.
Kernel in development(fixes, etc.) by vitek999 @ 4PDA
https://github.com/vitek999/LGE_H324_Kernel_3.10.54
ROMs for now:
Lollipop (all roms don't have a working hotspot, maybe something minor):
djperya @4pda
AOSP
Exception OS
lol_max_lik @4pda
RessurectionRemix
Dr.Leo6565 @4pda
BlissPop 4.0.3
AICPv10
CM12.1, needs patch, quite buggy
Marshmallow UI
Platinum L
Remix UI
Custom Mod H422
DoogeeOS
VibeUI
ZenUI
Sony Z4 Mod
LivUI
X-Pop
NovaUI
Sensetion OS
Xplay OS
DJUMANJI 4.0
ColorOS
Igronafr229 @4pda
GreatAOSP ROM
CleanPOP 7.0.2
Sense7
ROM galaxy note 5
LP Prime
AisakaYui @4pda
Stock, TWRP flashable
Marshmallow (extremely buggy, headphones don't work at high volumes, cameras barely work):
Dr.Leo6565 @4pda
CrDroid
AICPV11
Igronafr229 @ 4pda
CM13
Kernels for now:
OptiSmartKernel
How to flash?
Best method is MTK FlashTool(download)
Grab uboot (This is for devices that have android 5.0 on them, should work for all models, tested on my H420 and works)
Grab TWRP 3.0
1. Unzip Flashtool.
2. Get recovery.img and uboot.img from recovery and uboot zips.
3. Open flash-tool.exe
4. Select scatter file. which is in the same folder as flash-tool.exe
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5. Select your uboot and recovery.img click on the highlighted, it will open the file picker.
6. Turn off your phone, plug in usb cable in the computer.
7. Click the download button in flashtool, plug the usb cable.
8. Wait for it to say ok.
DONE!
To enter recovery:
1. Turn phone off.
2. Hold power and volume down
3. When screen turns on, let go of the buttons and quickly hold them again.
4. A menu should appear about factory reset. Don't worry, it won't since the recovery is custom.
5. Select yes using volume keys, you'll need to do it two times.
6. Voila!
To root stock 6.0, download this and place files in flashtool like in the guide above, just pick the files and flash. (recovery.emmc.win = recovery; logo.emmc.win = logo etc.) afterwards you can go ahead and get a magisk zip and flash it (it needs to be modified to be able to patch our device, thanks to the people @ 4pda for being so helpful) here
CREDITS:
Vitek999 for kernel and being very helpful
djperya for flashtool and being very helpful
Everyone else for the ROMs, thanks guys!
Kicka$$ stuff.
Tomo123 said:
Kicka$$ stuff.
Click to expand...
Click to collapse
Thanks, now that I have a working kernel source I'll make my own. Also overclocking will be very easy.
excuse me for my ignorance. Will this work with h440n?
Korelev said:
excuse me for my ignorance. Will this work with h440n?
Click to expand...
Click to collapse
No, these are completely different devices.
Aosp 5.0.2 language
hello today I installed the ROM AOSP 5.0.2 on my lg H420 and noticed that not had my language ( Portuguese - Portugal ).
Already I installed an application to change my language but some aplications as the system continue in English.
someone can give me a hand?
Thyago Vergueira said:
hello today I installed the ROM AOSP 5.0.2 on my lg H420 and noticed that not had my language ( Portuguese - Portugal ).
Already I installed an application to change my language but some aplications as the system continue in English.
someone can give me a hand?
Click to expand...
Click to collapse
Which applications are these? I think that some applications can use only English language.
polfrank said:
Which applications are these? I think that some applications can use only English language.
Click to expand...
Click to collapse
System apps like "phone" "settings" "contacts" "messaging"....
please i need to fix !!!
hello
my phone when i power off and when i put the cable dont do nothing just charge the phone...
can you helpe me?i have debbuging on and i try also off
anatol55 said:
hello
my phone when i power off and when i put the cable dont do nothing just charge the phone...
can you helpe me?i have debbuging on and i try also off
Click to expand...
Click to collapse
https://drive.google.com/file/d/0B_UKqVTCg2_xMUo2XzRzaWVaSzQ/view?usp=drive_web install this
Guys can i unlock bootloader of my lg h442
mayankjet said:
Guys can i unlock bootloader of my lg h442
Click to expand...
Click to collapse
yes just flash it as told to. There's even CM13 (android 6.0.1) just look up the 4pda thread.
so if i update h420 to marshmallow i'll still be able to flash it with this method and gain root access?
+&o_o said:
so if i update h420 to marshmallow i'll still be able to flash it with this method and gain root access?
Click to expand...
Click to collapse
forget my last question (kinda stupid). i have a problem if you guys could help me would be great. after flashing everything succesfully on the phone, wich is a spirit H420, under phone info now i get H422. it wouldn't be a problem if only i could flash the marshmallow kdz meant for the H420, but the installation process via LGUP doesn't even start. i've seen interesting stuff on 4pda, maybe i could find H420 lollipop stock there? to start from scratch before updating?
can anyone help me to revert the phone info?
+&o_o said:
forget my last question (kinda stupid). i have a problem if you guys could help me would be great. after flashing everything succesfully on the phone, wich is a spirit H420, under phone info now i get H422. it wouldn't be a problem if only i could flash the marshmallow kdz meant for the H420, but the installation process via LGUP doesn't even start. i've seen interesting stuff on 4pda, maybe i could find H420 lollipop stock there? to start from scratch before updating?
can anyone help me to revert the phone info?
Click to expand...
Click to collapse
In my case, I tried to upgrade my H420 from LP to MM via lg Mobile support tool or lg pc suite, but neither does the trick, constantly getting error. I have the MM .kdz file that is named as "H42020C_00_0530" but I tried to flash it through lg flashtool 2014, this one in vain too. What I should do to get Marshmallow? Thanks!
paulalastor said:
In my case, I tried to upgrade my H420 from LP to MM via lg Mobile support tool or lg pc suite, but neither does the trick, constantly getting error. I have the MM .kdz file that is named as "H42020C_00_0530" but I tried to flash it through lg flashtool 2014, this one in vain too. What I should do to get Marshmallow? Thanks!
Click to expand...
Click to collapse
apparently marshmallow can't be flashed using flashtool 2014, in 4pda there's a link to this video. the video is in russian, but to put it simply: go to lg site of your country, go to support, find your device, download drivers and "LG support tool" wich is a new version of the 2014 flash tool, install both of them, insert the phone turned on because the software needs to recognise the model of the phone. it will find the upgrade, "the phone may reboot, do not disconnect etc.", sadly it will go through the process of downloading the update from the internet, so no use of our kdz.
i've managed to get untill "upgrade available" step using a mobile connection, but since the firewall of my university is filtered (and beside the weight of the file, my phone would reboot, so no tethering) i can't update now. as soon as i get to a private connection i'll try. let me know if you succeed.
+&o_o said:
apparently marshmallow can't be flashed using flashtool 2014, in 4pda there's a link to this video. the video is in russian, but to put it simply: go to lg site of your country, go to support, find your device, download drivers and "LG support tool" wich is a new version of the 2014 flash tool, install both of them, insert the phone turned on because the software needs to recognise the model of the phone. it will find the upgrade, "the phone may reboot, do not disconnect etc.", sadly it will go through the process of downloading the update from the internet, so no use of our kdz.
i've managed to get untill "upgrade available" step using a mobile connection, but since the firewall of my university is filtered (and beside the weight of the file, my phone would reboot, so no tethering) i can't update now. as soon as i get to a private connection i'll try. let me know if you succeed.
Click to expand...
Click to collapse
No way with lg support tool, it didn't pass over the download of the firmware, just give error. I resolved following (by google translate) this: http://4pda.ru/forum/index.php?showtopic=686154&st=2500#entry50284916, then the green colored link Прошивка android 6.0 с нуля через LG Flashtool, finally download the attachment named H422, about 1,1 Gb. But the guide assumes that you utilize a firmware with .dz extension, not .kdz...We need an extractor/converter, just get this http://forum.xda-developers.com/attachment.php?attachmentid=3136613&stc=1&d=1422375946.
Then, if you have, like me, downloaded the v20c MM stock firmware from a site like this: http://lg-phone-firmware.com/index.php?id_mod=190, just extract the two files needed to flash our H420: "LGUPc.dll" and "H42020c00.dz". I hope I've explained myself well or almost....:silly:
If needed, just ask. I'm pretty happy with my solution.:victory:
---------- Post added at 08:22 PM ---------- Previous post was at 08:19 PM ----------
I'm just searching/waiting now for root process...
paulalastor said:
No way with lg support tool, it didn't pass over the download of the firmware, just give error. I resolved following (by google translate) this: http://4pda.ru/forum/index.php?showtopic=686154&st=2500#entry50284916, then the green colored link Прошивка android 6.0 с нуля через LG Flashtool, finally download the attachment named H422, about 1,1 Gb. But the guide assumes that you utilize a firmware with .dz extension, not .kdz...We need an extractor/converter, just get this http://forum.xda-developers.com/attachment.php?attachmentid=3136613&stc=1&d=1422375946.
Then, if you have, like me, downloaded the v20c MM stock firmware from a site like this: http://lg-phone-firmware.com/index.php?id_mod=190, just extract the two files needed to flash our H420: "LGUPc.dll" and "H42020c00.dz". I hope I've explained myself well or almost....:silly:
If needed, just ask. I'm pretty happy with my solution.:victory:
---------- Post added at 08:22 PM ---------- Previous post was at 08:19 PM ----------
I'm just searching/waiting now for root process...
Click to expand...
Click to collapse
DONE! thanks mate! owe you one
a clarification to anyone who might come here: the 2013 version of lg flash tool, wich is required for this guide is contained in the H422.rar of the russian guide. it took me a couple of minutes to understand. also i didn't understand the part of the green link, but i managed to update anyway, so i think your advice is pretty clear.
i'm not sure if this kind of update was needed for my device (didn't try upgrade tool), but since it was succesfull for you, i already posses the .kdz and i'm on a limited connection, i decided to give it a try...and SUCCESS!
already like marshmallow, hope memory leak doesn't affect our devices, and can't wait for root!
Some ROM`s
crDroid Android (6.0.1) - ttp://4pda.ru/forum/index.php?showtopic=686154&view=findpost&p=50064727
CyanogenMod 12.1 (5.1.1) - ttp://4pda.ru/forum/index.php?showtopic=686154&view=findpost&p=50327122
CyanogenMod 13 (6.0.1) - ttp://4pda.ru/forum/index.php?showtopic=686154&view=findpost&p=49486910
Blisspop (5.1.1) - ttp://4pda.ru/forum/index.php?showtopic=686154&view=findpost&p=50521514
AICP v10 (5.1.1) - ttp://4pda.ru/forum/index.php?showtopic=686154&view=findpost&p=50521514
Ressurection Remix (5.1.1) - ttp://4pda.ru/forum/index.php?s=&showtopic=686154&view=findpost&p=50521997
marshmallow root
quick update for you guys. it appears that on 4pda someone has managed to get permanent root.
here's the http://4pda.ru/forum/index.php?showtopic=686154&st=3180#entry50879512 link