Can't boot from SD Card - Nook Color Q&A, Help & Troubleshooting

I have a new-to-me Nook Color running the 1.4.2 firmware. I did a factory reset and set up my Barnes and Noble account. Yay me. However I can't FOR THE LIFE OF ME get it to boot off the SD card.
I've tried two 2GB cards (Samsung & SanDisk) and one 8GB SanDisk card. Also used three different card readers to burn the .IMG. What am I missing? I stick them in the Nook and the Nook just boots up as normal without hesitation. I've been rooting cell phones for years but this tablet has me stumped.
Is there another option I can use to flash CWM? Once I get it flashed I'm sure flashing the ROM is a breeze...
EDIT: After more and more digging, it might be an issue with writing to the wrong partition. How can I check to see if I'm installing to the write partition? I've formatted my cards multiple times. This is the stuff I see in a lot of answer posts:
of = /dev/disk# (good)
of = /dev/disk#p# (bad)
Click to expand...
Click to collapse

have you wrote an sd card that will boot (ie. Clockwork 4 gig et al). Can you read and write to it from within stock? More data please, what were you writing to what partition?
When I use the uSD card to boot and it is plugged into the computer you should hear three da-da-das.

n8nmad said:
have you wrote an sd card that will boot (ie. Clockwork 4 gig et al). Can you read and write to it from within stock? More data please, what were you writing to what partition?
When I use the uSD card to boot and it is plugged into the computer you should hear three da-da-das.
Click to expand...
Click to collapse
I have never successfully created an SD card that will boot on the Nook. Outside of the Nook, I have no way of testing to see if works or not.
You asked what partition, but I only have one partition on the card. If I open up the card in Disk Manager, there's just one allotment of space. When you burn the Image, is that supposed to create a separate partition that's visible in My Computer? If so, that's not happening because all the data is in one spot on the card (from what I can tell)

You need to flash the card. I suggest starting here:
http://forum.xda-developers.com/showthread.php?t=922870
or any of the other dev threads dealing with dual boots or whatever it is you are trying to accomplish.
Does your stock nook format sd cards to write books and such? If not that would be a big clue that it is a hardware issue

n8nmad said:
You need to flash the card. I suggest starting here:
http://forum.xda-developers.com/showthread.php?t=922870
or any of the other dev threads dealing with dual boots or whatever it is you are trying to accomplish.
Does your stock nook format sd cards to write books and such? If not that would be a big clue that it is a hardware issue
Click to expand...
Click to collapse
Yes, the stock Nook picks up the cards and formats them when installed. I've used these cards for all my smartphone rooting without any issues.
I've also formatted the cards and burned the CWM images using the windiskimager tool. It's just not bootable for some reason

The very first fundamentally step is to check whether it is a NOOKcolor or Nook Tablet.

votinh said:
The very first fundamentally step is to check whether it is a NOOKcolor or Nook Tablet.
Click to expand...
Click to collapse
Holy balls, I feel like an idiot. I had no idea the two were so similar. I am almost certain I have the Color (going by what it says on the case) but I'll look closely when I get home

It's the Nook Tablet. Wow....just...wow
On the bright side, at least my technical experience isn't the problem. My common sense on the other hand...

I believe you still can root the NT or run the pre-alpha ROM from it.
Unsure if it's able to run from uSD yet or not.

Related

[Q] Noob question: How to boot from SD?

I tried to create a CM7 bootable SD card per the thread entitled "Size-agnostic SD Card image and CM7 installer for SD Cards. with updater."
I used WinImage to create the supposedly bootable SD card with the installer, placed it into my Nook which was fully off, and the Nook booted as usual instead of from the SD card.
Am I missing something? How do you boot from an SD card?
Is there such a thing as a boot choice menu like on my PC or is the default always to boot from the SD card?
Does the Nook have to be rooted for this to work?
Thanks
ETA: My PC shows the uSD card as nearly full, but my Nook shows the SD card as nearly empty (1.74 out of 1.84 GB available).
When you bought your Nook, did it have a blue sticker on the box? And does internal storage show 1GB or 5GB for you?
Also, you did drop an update CM7 zip file onto the imaged uSD before you tried booting off it right?
angomy said:
When you bought your Nook, did it have a blue sticker on the box? And does internal storage show 1GB or 5GB for you?
Also, you did drop an update CM7 zip file onto the imaged uSD before you tried booting off it right?
Click to expand...
Click to collapse
No blue sticker was on the box. The internal storage shows 5GB.
Yes, I had a CM7 zip file on the imaged card. (The latest encore nightly)
Interestingly, my PC shows the uSD (2 GB) as nearly full. The Nook shows it as nearly empty (1.74 out of 1.84 available).
JowBe said:
No blue sticker was on the box. The internal storage shows 5GB.
Yes, I had a CM7 zip file on the imaged card. (The latest encore nightly)
Interestingly, my PC shows the uSD (2 GB) as nearly full. The Nook shows it as nearly empty (1.74 out of 1.84 available).
Click to expand...
Click to collapse
When you burned the installer img, did you run WinImage as administrator? Also, when you put it in your reader it comes up as boot (drive letter in Windows, with files like uImage, uRamdisk, mlo, u-boot.bin, right?
angomy said:
When you burned the installer img, did you run WinImage as administrator? Also, when you put it in your reader it comes up as boot (drive letter in Windows, with files like uImage, uRamdisk, mlo, u-boot.bin, right?
Click to expand...
Click to collapse
Yes, I ran WinImage as administrator. And yes, it shows up in Windows explorer as boot and yes those files are there.
Could it be because my Nook operates in "factory mode," in order to skip initial registration?
You should run it and register it and setup wifi and everything first. Get the stock software working fine and dandy (its not half bad actually). Then, checkout this guide for installing CM7 onto an SD card:
http://clubnook.com/forum/showthread.php?953-Rooting-Instructions
It has worked for some rooting rookies so far and includes both windows and mac guides specific to SD cards.
JowBe said:
Could it be because my Nook operates in "factory mode," in order to skip initial registration?
Click to expand...
Click to collapse
I'm not sure, because I ran through initial registration on stock prior to running CM7 off SD --- I used the same image (verygreen's agnostic at http://forum.xda-developers.com/showthread.php?t=1000957) as you did without a hitch.
If you decide to run CM7 off internal sometime you're going to need to register the nook anyway.
You could try an alternate bootable SD (e.g., using an image from here: http://forum.xda-developers.com/showpost.php?p=13283643&postcount=34) to eliminate one of the two: a) your nook having issues booting from SD or b) your SD install is not set up correctly.
An update: I decided to try to create a bootable SD from another bootable image (MonsterRootPack with CWR). This time the nook wouldn't even turn on. I'm going to try to create a third bootable SD as angomy has suggested to see what happens.
I need to add that when I removed the uSD card, it booted normally.
Also, when I create the bootable SD with winimage, I get a dialog box that tells me that the format of the SD card is not right and asks me if I want to resize the image. But this happened on both the images. I don't know if this has anything to do with it.
angomy said:
You could try an alternate bootable SD (e.g., using an image from here: http://forum.xda-developers.com/showpost.php?p=13283643&postcount=34) to eliminate one of the two: a) your nook having issues booting from SD or b) your SD install is not set up correctly.
Click to expand...
Click to collapse
Ok, I tried the CWR image in the link you gave. Same problem - no-go. Just sits there dead. I remove the uSD and it boots normally.
FWIW you do not have to boot into stock B&N at all before you setup and install to CM7 SD card. One of my NCs has never ever booted into stock ROM at all, I installed CM7 onto SD card and running off that from the moment it was unboxed.
The NC will always boot off the SD card first, so if it's booting off eMMC instead then there must be something wrong with the img that you wrote to your SD card.
Make sure that you have a freshly formatted SD card, preferably one with good small random block r/w speeds (eg Sandisk class 4 8G). Follow the instructions in verygreen's "Size Agnostic..." OP to the letter. Re-download all the files as you may have a corrupted one. Make sure to check MD5 this time. Try using Win32diskimager instead, the 0.1 version works better.
It should work. Good luck.
ebubar said:
You should run it and register it and setup wifi and everything first. Get the stock software working fine and dandy (its not half bad actually). Then, checkout this guide for installing CM7 onto an SD card:
http://clubnook.com/forum/showthread.php?953-Rooting-Instructions
It has worked for some rooting rookies so far and includes both windows and mac guides specific to SD cards.
Click to expand...
Click to collapse
Thanks for the link. I have given this some thought, and it doesn't seem reasonable that booting from an SD card should depend upon the state of registration of the device because the whole idea of booting from an SD card means that the content of the SD card is loaded in the place of the stock software.
robot8 said:
FWIW you do not have to boot into stock B&N at all before you setup and install to CM7 SD card. One of my NCs has never ever booted into stock ROM at all, I installed CM7 onto SD card and running off that from the moment it was unboxed.
The NC will always boot off the SD card first, so if it's booting off eMMC instead then there must be something wrong with the img that you wrote to your SD card.
Make sure that you have a freshly formatted SD card, preferably one with good small random block r/w speeds (eg Sandisk class 4 8G). Follow the instructions in verygreen's "Size Agnostic..." OP to the letter. Re-download all the files as you may have a corrupted one. Make sure to check MD5 this time. Try using Win32diskimager instead, the 0.1 version works better.
It should work. Good luck.
Click to expand...
Click to collapse
Thanks. Yes, I just replied to another poster that I didn't think that the state of registration of the device should matter since the whole purpose of a bootable SD card is to load the contents of the SD in place of the stock.
I have followed the instructions in verygreen's thread to the letter - several times. Also, I have tried to make other bootable SDs without success. But that's a good idea about trying Win32diskimager. Also, I will try a Sandisk class 4 card SD as soon as I can get to a store.
I do have a question. When I format the SD card what "allocation unit size" should I be using? (formatting through Windows) The default is 32 kb.
PROBLEM SOLVED!
Thanks to everyone for trying to help me figure this out. The winning idea belongs to robot8.
When I switched from using WinImage to using Win32diskimager, it worked immediately. I am now running CM7 on my Nook Color! Took forever and a day to boot though.
Congrats!
Re: allocation unit size, do you mean cluster size? Depends on how big the FAT32 partition is --- larger clusters used means more actual space used but too large a size can reduce access speed. Generally Windows defaults to suggested 4k for up to 8GB, 8GB-16GB = 8k, 16-32GB = 16k, and 32+ = 32kb.
Also the first boot is the longest --- shouldn't take as long after that. Welcome to CM7 - I don't regret installing it over stock after waffling for weeks on whether or not I'd use stock at some point -- CM7 is just too much faster with too many more options and tweaks for my impatience to deal with stock Froyo.
THANK YOU OP!
I had the same issue, tried 20x various ways, 2 different computers, 2 different SD readers, and it was WinImage that wasnt working correctly. Win32DiskImager solved it.
Thanks.
JowBe said:
PROBLEM SOLVED!
Thanks to everyone for trying to help me figure this out. The winning idea belongs to robot8.
When I switched from using WinImage to using Win32diskimager, it worked immediately. I am now running CM7 on my Nook Color! Took forever and a day to boot though.
Click to expand...
Click to collapse
Thanks so much! This finally got it to work for me too. Loving my new Android tablet
FWIW, WinImage does not work. Maybe it used to work, but it does not now. I posted about this a few days ago here.

[Q] Help with partitioning SD Card

Hello first I want to say a big THANK YOU to everyone that has put time and effort into making the Nookie what it is today....but I have a noob question.
I recently got a 16gb micro SD and can successfully get the 0.6.8 Nookie to run on my nook color, my problems start when I try to "recover" my other 13gb's. Before I get burned and tossed aside I have checked
http://forum.xda-developers.com/showthread.php?t=922324&page=92
http://forum.xda-developers.com/showthread.php?t=883175&highlight=partition&page=103
and about 5 other pages and they all say the same thing..use EASEUS, grab the slide bar and voila. It appears to work but when I install it in the NC it either becomes very unstable or just boots to the NC as if the SD card was not there.
Anyone have any ideas?
Jeep_Lover said:
Hello first I want to say a big THANK YOU to everyone that has put time and effort into making the Nookie what it is today....but I have a noob question.
I recently got a 16gb micro SD and can successfully get the 0.6.8 Nookie to run on my nook color, my problems start when I try to "recover" my other 13gb's. Before I get burned and tossed aside I have checked
http://forum.xda-developers.com/showthread.php?t=922324&page=92
http://forum.xda-developers.com/showthread.php?t=883175&highlight=partition&page=103
and about 5 other pages and they all say the same thing..use EASEUS, grab the slide bar and voila. It appears to work but when I install it in the NC it either becomes very unstable or just boots to the NC as if the SD card was not there.
Anyone have any ideas?
Click to expand...
Click to collapse
I use Lexar Bootit ....a free utility...to format and flip the bit that says its a removeable drive, then your windows pc drive management can see and format it as full capacity fat32.
Hey thanks for the tip, unfortunately it won't work. I forgot to mention that I followed this tutorial ..... and updated my driver (saved my original Windows just in case) to a hitachi driver and now I can switch my SD memory card forth "removable" to "logical" and back when needed. Once I get it as a logical drive I was EASEUS to increase the size of partition 4 (SD Card)..but again no dice!!!
Seeing that I am a noob I can't post the link to the tutorial but I'll say it worked like a charm and when I want to go back to the original I just need to "roll back" the driver.
Well, a couple of things:
Are you using a Sandisk card? Sandisk class 2 and 4 cards have been found much more stable than most others for running a ROM from SD, and problems with SD installs often go back to the card.
Any particular reason you went with Nookie Froyo? It has pretty much fallen out of use since the NC's stock OS was updated to Froyo in May. If you want an SD install, there's a simpler, size-agnostic method for CM7, which is also a more robust and capable OS and a more advanced version of Android (Gingerbread 2.3.4 rather than Froyo 2.2). I would recommend CM7.1 RC1, or if you're adventurous, Nightly 136.
Taosaur said:
Well, a couple of things:
Are you using a Sandisk card? Sandisk class 2 and 4 cards have been found much more stable than most others for running a ROM from SD, and problems with SD installs often go back to the card.
Any particular reason you went with Nookie Froyo? It has pretty much fallen out of use since the NC's stock OS was updated to Froyo in May. If you want an SD install, there's a simpler, size-agnostic method for CM7, which is also a more robust and capable OS and a more advanced version of Android (Gingerbread 2.3.4 rather than Froyo 2.2). I would recommend CM7.1 RC1, or if you're adventurous, Nightly 136.
Click to expand...
Click to collapse
Thanks for the info unfortunately I am using a 16gb PNY, class 4 and at $15 I couldn't pass it up...looks like I should have done some more reading first. Really I have no clue why I am using the Nookie, my wife said said that was the one she wanted. I think she just likes saying "Nookie", but I'll give the CM7 a go and see what trouble I can get into.
thanks again...
Taosaur...I was able to get the CM7 mod up and running in no time flat. Now the wife wants me to see if I can get bluetooth working.
You said "I was able to get the CM7 mod up and running ...." so I assume you got your problem fixed. That's good.
About bluetooth.
1. Turn off Wifi
2. Power off NC
3. Power on NC
4. Turn on bluetooth
5. Turn on wifi
votinh said:
You said "I was able to get the CM7 mod up and running ...." so I assume you got your problem fixed. That's good.
About bluetooth.
1. Turn off Wifi
2. Power off NC
3. Power on NC
4. Turn on bluetooth
5. Turn on wifi
Click to expand...
Click to collapse
Yep, I had to do the above the first time I turned on bluetooth, but haven't had any trouble toggling it on and off since then. Just open notifications (that broken-circle-and-arrow button on the status bar) and you have toggles there for Wifi, bluetooth, and a couple other things.
@ Taosaur,
I've seen your signature indicate you are running nb136, any change or improvement (both slightly and/or significant) over the previous ones?
Jeep_Lover said:
Thanks for the info unfortunately I am using a 16gb PNY, class 4 and at $15 I couldn't pass it up...looks like I should have done some more reading first. Really I have no clue why I am using the Nookie, my wife said said that was the one she wanted. I think she just likes saying "Nookie", but I'll give the CM7 a go and see what trouble I can get into.
thanks again...
Click to expand...
Click to collapse
Damn! My wife never says "nookie".
votinh said:
@ Taosaur,
I've seen your signature indicate you are running nb136, any change or improvement (both slightly and/or significant) over the previous ones?
Click to expand...
Click to collapse
I haven't done much but read and browse a little since I flashed it, but I haven't noticed any difference from 7.1 RC1, which wasn't really any different from Nightly 102 I had before that. I mostly just flashed this time for the integrated OC/Tweaks kernel, without the video/lag problems that were reported in 132-134.
Thanks for an update, m8
maybe someone can help me, i'm about to loose my mind here trying to figure this out. i'm using a Sandisk class 4 16gb card running CM7 with the OC kernal.Did all of this using the size agnostic install method. everything is working fine but i can't for the life of me figure out how to access the rest of the space on my SD, when i insert the sd card into my PC it just shows up as the 115mb partition. i've tried using EASeus, the lexar bootit, and some other partition tool with no luck. with Easeus i select the 13gb FAT32 partition and make it active and thats it right? does it need to be logical? and which partition am i resizing?
Dr. Light said:
maybe someone can help me, i'm about to loose my mind here trying to figure this out. i'm using a Sandisk class 4 16gb card running CM7 with the OC kernal.Did all of this using the size agnostic install method. everything is working fine but i can't for the life of me figure out how to access the rest of the space on my SD, when i insert the sd card into my PC it just shows up as the 115mb partition. i've tried using EASeus, the lexar bootit, and some other partition tool with no luck. with Easeus i select the 13gb FAT32 partition and make it active and thats it right? does it need to be logical? and which partition am i resizing?
Click to expand...
Click to collapse
None of the above. Windows will only recognize the first partition on a SD card, and when you make a SD bootable, that first partition will be the boot partition. To access the larger storage partition, connect your NC with CM7 running to the PC over USB. Open notifications on the NC, tap through "USB connected" to the USB screen, and "Turn on USB storage." Windows will now detect two storage drives, NookColor (the system partition, where apps install) and SDcard (the large storage partition).
The only time you'll want to remove the card from the NC and plug it into your PC is when you want to put on a new cm...zip update file to flash a new ROM.
I used the size agnostic install method with a 16gb PNY calss 4 SD and after all the steps were completed I was showing 13.8gb free for my SD card when I looked at in on the NC. Not believing my eyes I pulled it out and looked at it with EASUS and it showed partition 4 as 13.8gb (utilizing all the cards remaining space). I then downloaded a few things and added a few books for my wife and the space shrank to 13.4gb. As stated above your computer wont show it.
In short have you looked on the NC under "Storage" (I think that is were I found it) and verified you don't have the full capacity already?
Also there is another method I needed to use when I was messing with an earlier version (Nookie) that allowed me to see an SD card as a "Local Device" so windows would let me see all partitions on the hard drive. I can't post a link until I have more posts but email me and I can send you the link if interested.
Taosaur said:
None of the above. Windows will only recognize the first partition on a SD card, and when you make a SD bootable, that first partition will be the boot partition. To access the larger storage partition, connect your NC with CM7 running to the PC over USB. Open notifications on the NC, tap through "USB connected" to the USB screen, and "Turn on USB storage." Windows will now detect two storage drives, NookColor (the system partition, where apps install) and SDcard (the large storage partition).
The only time you'll want to remove the card from the NC and plug it into your PC is when you want to put on a new cm...zip update file to flash a new ROM.
Click to expand...
Click to collapse
thanks, well that got me some where. i connected nook to PC, turn on storage mode and it shows E/F drive. click either one and it says "Please insert disk into removable disk E/F" so then i turn off debugging and the nook color internal memory pops up as drive F, while clicking on drive E gives me the same error as above. any ideas? btw i'm on Windows 7 64bit, do i need any kind of special drivers or anything?
It is because windows will only allow you to manipulate the first partition on an SD card...even if it "sees" the other partition as another card it will not do anything with it. EASEUS will show you all the partitions on the SD.
The only way I got Windows to see all the partitions and do anything with them was to change my driver via the "Hitachi fix" If you google Hitachi driver SD card you will find it. I used this site and even though it is long it did exactly as advertised and now I install this driver when I need to format just the partition of an SD card and then "roll back" the driver when I'm done. It tricks windows into thinking it is a local device instead of removable. www/1src/com\forums\showthread.php?t=133718
change / to .
\ = /
I can't post a link as I'm still a noob...
Jeep_Lover said:
It is because windows will only allow you to manipulate the first partition on an SD card...even if it "sees" the other partition as another card it will not do anything with it. EASEUS will show you all the partitions on the SD.
Click to expand...
Click to collapse
S/he really doesn't need Windows to do anything with those other partitions--I suspect messing with them was where s/he went wrong in the first place.
Dr. Light said:
thanks, well that got me some where. i connected nook to PC, turn on storage mode and it shows E/F drive. click either one and it says "Please insert disk into removable disk E/F" so then i turn off debugging and the nook color internal memory pops up as drive F, while clicking on drive E gives me the same error as above. any ideas? btw i'm on Windows 7 64bit, do i need any kind of special drivers or anything?
Click to expand...
Click to collapse
I suggest you start over, because you probably damaged your install when you were messing with the partitions earlier. I'm also using Win7x64, and no, I didn't need any special drivers. Delete all partitions except "SDcard" in EASEUS, expand that partition to the whole card, then write verygreen's image to the card again and re-install. At that point, you should be able to access storage over USB from CM7 without turning off debugging or taking any other special steps other than "Turn on USB storage."
Taosaur said:
S/he really doesn't need Windows to do anything with those other partitions--I suspect messing with them was where s/he went wrong in the first place.
I suggest you start over, because you probably damaged your install when you were messing with the partitions earlier. I'm also using Win7x64, and no, I didn't need any special drivers. Delete all partitions except "SDcard" in EASEUS, expand that partition to the whole card, then write verygreen's image to the card again and re-install. At that point, you should be able to access storage over USB from CM7 without turning off debugging or taking any other special steps other than "Turn on USB storage."
Click to expand...
Click to collapse
alright i'll give it a shot when i get home from work. is the verygreen image the same one found in the CM7 size agnostic SD thread?
"http://crimea.edu/~green/nook/generic-sdcard-v1.3.img.gz"
and when i delete all partitions except for "SDCARD" do i need to make that partition logical or active or anything?
again thanks for your help.
Dr. Light said:
alright i'll give it a shot when i get home from work. is the verygreen image the same one found in the CM7 size agnostic SD thread?
"http://crimea.edu/~green/nook/generic-sdcard-v1.3.img.gz"
Click to expand...
Click to collapse
Yep, verygreen is the author of that thread and image.
Dr. Light said:
and when i delete all partitions except for "SDCARD" do i need to make that partition logical or active or anything?
Click to expand...
Click to collapse
No, in fact you might be able to write the image without messing around in EASEUS at all--I'm just not sure if WinImage (or whatever) would write to the whole card or just one partition. I know if you tried to format it, Windows would only format the boot partition.

[Q] Unable to boot my ~unmodified~ Nook Color from SD card.

I just got a refurbished Nook Color. Seems to work fine but you have to push the power button hard to click it.
Haven't rooted, installed roms, anything yet. But I can't get it to boot from my SD card. I have a 4GB (class-4) microSD card. (I have checked the sdcard for bad blocks using the linux "badblocks" command.) I have followed instructions detailed here:
glasskeys. /2011/06/27/how-to-make-a-bootable-sd-card-running-cyanogenmod-for-the-nook-color/
and here [note - new users are forbidden from posting links here - in the above and below links, I left out the "com" after the dot in the website address]:
nookdevs. /Nookie_Honeycomb:_Burning_a_bootable_SD_card
. I use Ubuntu Linux 10.11 "dd" command to write the .img files to the SD card. However, once I write the SD card and put it into my Nook, the nook won't turn on. Just won't turn on. As soon as I take the card out and try again, I can boot up the nook to the locked-down, walled-garden stock Android on the device.
Help! Is something wrong with my SD card, or with my device? I have a 2GB microSD card somewhere I can find if I need to...
Re:
Can anyone help me find the source of the problem? Is it my SDcard, my card-burning technique (i followed the dd instructions word for word), my computer or is something wrong with my Nook?
What I might suggest is to discard your original source of instructions and start fresh. Search the xda forum for clear information on 1) proper mSD card to use; 2) proper card burning software; 3) the most appropriate rom(s) to use for what you want your Nook to do for you, and 4) if necessary, very explicit instructions to troubleshoot any problems you may encounter with your processes. I'll not point to specific locations here, because I'm not sure what you actually want to do, But the search engine is very thorough and the threads are numerous.
Good luck. I'm sure you'll be quite content with your newly rooted/rommed NC.
yanom said:
Can anyone help me find the source of the problem? Is it my SDcard, my card-burning technique (i followed the dd instructions word for word), my computer or is something wrong with my Nook?
Click to expand...
Click to collapse
I have a section in my tips thread linked in my signature that deals with bootable SDs, but I'm not sure it's going to help you. I was helping another user that had the same exact problem where the Nook would not power on with the SD in. One of the things I had him do was fully charge his Nook. I can't remember how he resolved it though, if he did. But I suspect a faulty Nook or SD. Pins bent or something.
Sent from my Nook Color running ICS and Tapatalk
leapinlar said:
I have a section in my tips thread linked in my signature that deals with bootable SDs, but I'm not sure it's going to help you. I was helping another user that had the same exact problem where the Nook would not power on with the SD in. One of the things I had him do was fully charge his Nook. I can't remember how he resolved it though, if he did. But I suspect a faulty Nook or SD. Pins bent or something.
Sent from my Nook Color running ICS and Tapatalk
Click to expand...
Click to collapse
Thanks. It's worth noting that, if I get an SD with normal data (photos, etc) on it and put it in while the nook is booted normall, the nook can read the card and see what's on there. So the nook can read cards. That doesn't mean the boot-up bits aren't screwy.... this is refurbished.
Update
Update: I got it to work. However, it's quite laggy, possibly because it's Honeycomb on a class 2 (low IO speed) card. Can anyone point me to a super-slimed android (don't care what version) .img file I can put on my card?
yanom said:
Update: I got it to work. However, it's quite laggy, possibly because it's Honeycomb on a class 2 (low IO speed) card. Can anyone point me to a super-slimed android (don't care what version) .img file I can put on my card?
Click to expand...
Click to collapse
Oh, do not use Honeycomb. It is terrible. Use CM 7.2. They just this weekend came out with a stable version. Cyanogenmod.com. Look for encore stable. And your class 2 should work great.
Sent from my NookColor using Tapatalk
leapinlar said:
Oh, do not use Honeycomb. It is terrible. Use CM 7.2. They just this weekend came out with a stable version. Cyanogenmod.com. Look for encore stable. And your class 2 should work great.
Sent from my NookColor using Tapatalk
Click to expand...
Click to collapse
Let me +1 the latest and greatest CM 7.2. I was using a supposedly faster card with 7.1 on an NC and I also experienced a lot of lagging.
Switching to a class 4 SanDisk card and going to 7.2 fixed the problem. Since I did both at the same time, I can't tell you what exactly made the difference but if installing 7.2 does not fix the issue, try changing your card.
I followed these instructions which installs CM7 on your SD card so you can dual boot if necessary. Also, this has the same exact info written in a slightly less techie language. (I am not sure why he is trying to use the hardware keys to reboot into the recovery mode when it can be done easily from within CM7.)
Good luck!
I know this is a super old thread, but it seems like an appropriate place to post. I've got three Nook Color tablets from my niece and nephews. I flashed them with Mirage Cyanogenmod 7.2 via CWM on an SD card. Once I got the SD setup, I went through two of them in 10 minutes total. No sweat. I installed two fresh, out-of-the-box SD cards in each tablet, which left the modded, CWM SD card untouched after flashing the first two. The third one was missing for several weeks. They just found that one. They dropped off the third tablet along with the modded SD card, which was sealed in a ziplock bag, to me. I installed the card into the third Nook Color, which was untouched after flashing the first two, and the third Nook Color booted right past the SD card and into the stock OS. I've reflashed the same .img file and others, including verygreen's onto this SD card. It simply refuses to boot from the SD. I've tried writing the .img file from WinImage, and WinImage32 through the SD slot on my laptop, an SD card adapter via USB, and through the nook itself as a mass storage drive. I'm stumped. Any thoughts?
On a side note, I don't have access to the first two to confirm the SD card is still on track, nor do I, at this point, have a spare SD card to troubleshoot with. Those are my next steps to take, but I am curious what the experts might have to suggest in the mean time. Thanks in advance, and I'll post my solution, if I solve this.
Are you sure the third one is a Nook Color? It could be a Nook Tablet. They look the same, but the Tablet has a silver bezel instead of black. Those cards will not boot on a Tablet.
Sent from my Nook HD+ running CM10 on Hybrid SD
leapinlar said:
Are you sure the third one is a Nook Color? It could be a Nook Tablet. They look the same, but the Tablet has a silver bezel instead of black. Those cards will not boot on a Tablet.
Sent from my Nook HD+ running CM10 on Hybrid SD
Click to expand...
Click to collapse
My first thought was "that's a ridiculous question. Of course it's a Color!", but then I peeled the cover off, and the bezel is indeed silver. Looks like I have some more reading to do. Thanks for saving me a TON of grief and frustration.
Just to follow up, I followed the instructions for flashing Cyanogenmon on the Nook TABLET, thank you Leapinlar, and everything is good. Thanks again.

[Q] Chronic "Unexpected Lack of Boot Partition on the SD card! Please Report"

[Q] Chronic "Unexpected Lack of Boot Partition on the SD card! Please Report"
Hi,
First let me say - YES, i have searched all of the forums here (and a number of other sites) and seem to have tried almost every option.
I have Chronic "Unexpected Lack of Boot Partition on the SD card! Please Report" problems. The farthest I get guaranteed is the cyanogenmod boot and menu (if I try and bring it up). I'm simply trying to get the SD card with cm7 to boot reliably and not eventually loose the boot partition.
Off and on since spring I was able to burn a CM7 image (verygreen's size agnostic, and one or two others I have since lost track of) to a SD card; have had it boot to cm7 and it work for awhile - but then eventual degraded into the no partition found error. the majority of the time it just doesn't work and results in that annoying purple black screen.
When it does work, it only works for awhile and then the boot partition can't be found; a few very small 3 of times - if I copied a new update it woke back up ad worked for a couple of reboots then lost the partition again.
Anybody got time to take pity on my melted brain and take a few guesses?
Clearly I'm not only missing something - but as things have gotten worse, am now missing more (if that is possible) as I'm going backwards to see why it no longer works at all.
At this point wrong has happened so often, I'm just lost on what even worked way back when I started.
I'm trying to backtrack to where it at least worked a little for a few days...but noob world is decaying into worse world.
I tried a couple of other, older processes and a multiboot menu one that seemed promising (plus could handle the new naming conventions for 7.2 CM7); but that one never even got past the missing boot partition.
I have tried approx 10 2gb SDCards, Sandisk, Kingston, Unknown; Class 4 and mixed.
I have tried 3 8GB SD Cards, Sandisk, class 4
I have tried 1 16gb SD Card, Sandisk, class 4
I have tried a Vivitar Micro SD Card Reader
I have tried the micro SD card Adapters in a laptop, and then in a sandisk USB adapter.
I even tried doing it all using the Nook color via a USB cable.
I even tried leaving the nook color off and connecting the USB cable to the PC to initiate a boot.
Using Windskimager
Using SD formatter
Have formatted Full erase and overwrite.
Tried leaving partition size alone
Tried partition resizing up to 250mb
Tried cm7 zip alone and with gapps
WinXP on 2 desktops and a laptop
It sounds like you have run the gamut of attempted resolutions.
That message is part of the verygreen partitioning script that runs every time the verygreen recovery is run. So, that means the normal boot kernel for CM7 is not loading.
The way the verygreen SD should operate is it starts with uImage and uRamdisk on the boot partition. Those are verygreen's recovery files. The first time it is booted, it looks at your emmc to be sure it is a nook. Then it looks at the SD to see if it has been partitioned yet. If it is not, it partitions it into those partitions necessary for installing ROMs. After partitioning, it looks for a zip to install. If it does not find one, it shuts down and the next time it boots it does the same thing until it finds the first ROM zip to install. If it finds one, it installs it. The first time it installs a ROM, it renames those uImage and uRamdisk verygreen files to uRecImg and uRecRam and they become the verygreen recovery files. And it installs new uImage and uRamdisk files from the zip to become your CM kernel and ramdisk. These are what normally will load in the future to start CM.
Now, with the disk partitioned and CM installed, ordinarily, after the cyanomod logo comes up, it boots by default to CM via the uImage and uRamdisk files. If you intercede with the boot menu and tell it to boot to SD recovery, it looks for uRecImg and uRecRam to load the verygreen recovery. If that is loaded, the verygreen script does all its checking again, it verifies that emmc is a nook, then tries to verify if the SD is partitioned. If it is, it looks for a new zip to install. If, in checking to see if it is partitioned, it cannot find partition 1, it gives that message that has been bugging you.
So I see two things that are happening to you.
First, it is booting to the verygreen recovery first instead of CM. That could be due to a recovery bootloop happening. Look at my tips thread linked in my signature to see an explanation as to what that is and how to possibly get out of it.
Second, after it boots to the verygreen recovery, it does its checking and cannot find partition 1 of the SD and gives you that message.
What I cannot understand is, if you have no partition 1 on your SD, how is it booting to the verygreen recovery?
What you have not told us is what you have on emmc. Stock? Does it boot properly without the SD installed? Or does it go to stock recovery?
After this happens to you again, take the card out and put it in the PC. Tell us what you see. What files are there? Maybe look at it with Mini-Tool Partition Manager and see what partitions it reports.
leapinlar said:
What you have not told us is what you have on emmc. Stock? Does it boot properly without the SD installed? Or does it go to stock recovery?
Click to expand...
Click to collapse
Ditto on that - especially as it boots happily to that error message time after time after the green cyanomod screen appears and I can also do the menu trick to get it to go into recovery.
Just as a clarifier: A number of times it tried to do the install (text flowing by) and at the end claims it can't find the boot partition - odd (unless I have less of an idea of what I am doing than I think) as isn't all that running from that partition? A fairly even number of times it doesn't even run the install and just errors out right up front.
Once in a great while it all works, and I'm good for a few days - but eventually upon rebooting to get it back to normal (either by menu choice or by pulling the sd card) - all I get is that lack of partition again.
leapinlar said:
What you have not told us is what you have on emmc. Stock? Does it boot properly without the SD installed? Or does it go to stock recovery?
Click to expand...
Click to collapse
Yes with the SD card out it boots to stock, although a few time what looked like the CWMod menu came up after I shut down and started up without the SD card installed. Maybe only 2 or 3 times out of WAY to many boots to stock so the kids could read their books while I went to work.
I have even tried resetting the nook to factory on the off chance I did something dumb while mucking about to cause that.
leapinlar said:
After this happens to you again, take the card out and put it in the PC. Tell us what you see. What files are there? Maybe look at it with Mini-Tool Partition Manager and see what partitions it reports.
Click to expand...
Click to collapse
Will do so later tonight and will read the notes in your signature as well.
I saw something go by about the boot partition having to start at the 63 block or something - I can't believe ALL my SDcard adapters / writers are bad, but could the nook reader be screwy? Anyway to do a real test? I've been using the Easeus Partition Manager, but will try the Mini-Tool Partition Manager.
Thanks for the step by step explanation of exactly what happens in the process so I can again get a handle on what it's all doing. That all makes sense to what it looks like it tries to do. Deeply appreciate the time!.
You know, I am beginning to suspect something is wrong with your card reader built into the nook. Some sort of intermittent thing like a pin not making a good connection to the card. Put an ordinary SD in it and see if your stock can consistently read it.
Is your unit still under warranty? You might want to explore seeing if you can get it replaced.
Your downloaded verygreen image might be corrupted. Have you tried re-downloading it?
Sent from my NookColor using xda app-developers app
leapinlar said:
You know, I am beginning to suspect something is wrong with your card reader built into the nook. Some sort of intermittent thing like a pin not making a good connection to the card. Put an ordinary SD in it and see if your stock can consistently read it.
Is your unit still under warranty? You might want to explore seeing if you can get it replaced.
Click to expand...
Click to collapse
I had thought of that too - at stock it seems to have no problems reading consistently; I've done surface tests using partition manager - but haven't located any real other options of hard testing like once done for hard drives.
Plus the fact that sometimes, it will work for days before it craps out.
j8048188 said:
Your downloaded verygreen image might be corrupted. Have you tried re-downloading it?
Sent from my NookColor using xda app-developers app
Click to expand...
Click to collapse
A number of times - I went through and wiped all my downloads for the latest try.
Okay So As I mentioned I went back and wiped everything I had downloaded and restarted (again).
Current status is it's working BUT:
suspiciously too easy this time, worked first shot
- (having said that, I've had looking stupid and asking suddenly means it all starts working - so if it's that I'm good with this)
I've only rebooted into CM7, not back to stock at any time
Have not removed the SD card
I've not had time to load up the apps I like, just the kids games
- (sometimes I think it's the more wanted, the less reliable)
Obviously because I haven't removed the SD card, i haven't been able to retry things enough to recreate the other problems of boots right, yet can't find the partition when it really counts.
Changes (listing stupid things too, just because):
-Went back to my sandisk class 4 16gb HC card
-changed USB adapter back to sandisk one, using a sandisk micro to SD adapter that specifically says sdhc (although I think that is really just marketing
-Formatted the SD in the Nook x2, and did not use SDformatter
-Looked at the partition on the card with MiniTool not Easeus partition manager
-There is a step in verygreen's where you pop the card out and reconnect to the PC BEFORE adding the cm zip, made sure to do that - but could swear I had done it before.
Full painful boring steps that SO far has gotten it past the first stage of creation (again the full test is when I boot into stock a few times, or remove the SDcard for anything, or load my really wanted apps on the android side):
--Also note my lack of class 4 Sandisk cards, I only had one after all. BUT I have had this all work to this point with the 16gb only to have it go south.--
Painful details is so I can catch what is really worthwhile different as even WHEN I get it to work, I'm going back to try all the other cards because it worked so oddly and failed so oddly and differently - but that's just me.
> The 2GBs are:
6 Sandisk SD, don't see any class Rating
2 no brand SD, don't see any class Rating
1 Kingston SD, don't see any class Rating
> The 8gb are SDHC "Adata" Class 4 SDHC
> The 16gb is a Sandisk Class 4 SDHC
Using the 16GB Sandisk Class 4
--------------------------------
> Nook booted to stock
Inserted SD Card
Unmounted
Formatted sucessfully
unmounted and removed
> Put in Red SD / SDHC Adapter
Put in Sandisk MicroMate SDHC to USB Adapter
Put in Front USB spot
> Mounted as E Drive
E Drive shows standard Nook Folders:
.amdroid_secure
B&N Downloads
LOST.DIR
My files
> MiniTool Partition Wizard
Surface test = all good.
>Write the image on your SD card
Used Win 32 Disk Imager
After done with writing, eject and then re-insert the uSD card into your computer.
Two Partitions - 118 and 14.72gb
>Copied to card:
update-cm-7.1.0-encore-signed.zip
Installed correctly
configured wireless
Rebooted = OK
Rebooted = OK
>Turned off
Removed SD Card
Put in Red SD / SDHC Adapter
Put in Sandisk MicroMate SDHC to USB Adapter
Put in Front USB spot
copied gapps
>Boot into Recovery
Gapps installed
> boot
all good
did all set ups like before
added apps (7 games for kids)
rebooted twice
started using
added one app I really like (newshog)
Listening for drumming... nothing so far (Dr. Who reference)
I'm going to go the weekend before rebooting to stock as I can do some adding, and rebooting to android.
Maybe backup the droid side this time around.
THEN the death tests on Monday
-thanks for listening_
p.s. - Yes, I still suspect the card reader somewhat as REMOVING may be where it breaks down.
However, once or twice when I had the Unexpected lack of boot partition error - I was able to bring it back by doing a CM7 update via recovery, despite it refusing to find the boot partiton immediately previously - of course that means the SDcard was removed and reinserted. Most time reinsertion = no help.
You do not need to remove the SD to test booting to emmc. Just press and hold the n button during the boot until the boot menu comes up. Then select emmc/normal and boot. It will boot to stock. The only problem with doing that is now your SD boot partition is 'sdcard'. But should work for testing stock.
leapinlar said:
You do not need to remove the SD to test booting to emmc. Just press and hold the n button during the boot until the boot menu comes up. Then select emmc/normal and boot. It will boot to stock. The only problem with doing that is now your SD boot partition is 'sdcard'. But should work for testing stock.
Click to expand...
Click to collapse
Yes, I know - but it's two separate tests to see which one caused the problem.
Turns out that neither was needed - it was easier to create; my son simply turned it off (not a reboot cycle as I had been doing which worked).
When it was turned on, it no longer boots - it goes straight to BSOD (actually deep purple).
Booting into recovery gets me:
Penguin Logo
rcS!
Populating /dev using udev: done
Initializing random number generator.... done.
modprobe: chdir(2.6.32.9): No such file or directory
Starting Network...
Detected Standard B&N nook layout, emmc first
Error! Unexpected lack of boot partition on the SDCARD!
Please Report!
Poweroff when ready
Since I'm till held to the noob reposting limit of once every 5 minutes and the captha I can barely read - I'll post MiniTool result in about 5 minutes. I'll link a screen capture if i can here.
I tried to boot per menu to the EMMC stock; Clockworkmod Recovery v3.2.0.1 came up. I know I did emmc and what ever the second default is (which should be normal) - I'm pretty sure it was normal.
I offed it and did the same and confirmed it was the default; THIS time it came up Nook stock.
Is there some way I installed something to the stock NOOK and didn't remove it when I restored to factory? The other day I did the restore from that same clockworkmod screen NOT from the stock Nook environment.
I'm wondering if I somehow created my own monster way back when I first started this and was playing in the android environment.
I just edited what I wrote a few seconds ago. The reason it went to emmc recovery is because the recovery flag was not reset when that SD Recovery told you that error. Did you read my tips about recovery bootloops? When you exited 3.2.0.1, it cleared the flag and booted normally.
I still suspect hardware issues.
Just for Ha, Ha's I hooked the Nook via USB to the PC.
G Drive "Removable Disk G" (wants a disk to be inserted)
E Drive "MyNookColor" ( Lots of what I assume to be standard Nook folders.
See my edit above.
Attachement # 1 SD Card from Mycomputer:
Attachment # 2 MiniTool View of SD Card
Boot Partition
Properties using Minitool Partition Wizard (attached):
Used
Partition Info
File System Info
Surface Test of Boot Partition:
Perfect - so no picture.
This is SO aggravating - I almost would accept just knowing why rebooting wrecks something if I knew WHAT).
leapinlar said:
I just edited what I wrote a few seconds ago. The reason it went to emmc recovery is because the recovery flag was not reset when that SD Recovery told you that error. Did you read my tips about recovery bootloops? When you exited 3.2.0.1, it cleared the flag and booted normally.
I still suspect hardware issues.
Click to expand...
Click to collapse
Sorry, apparently not closely enough - got lots of time again.
....didn't expect that anyone would be watching, was busy posting pictures so I could go away and read and think...
Probably is hardware - wish I had some way to vigorously test that, I get that basic use in Nook Stock doesn't really prove everything is good.
Plus I bought refurbished and I have to go dig up the warranty, it was months ago, so not too hopeful and boxes long gone. Don't know how nice B&N is, free replacement charger and cord is one thing - whole another refurb unit is different if I can't show stock SD card reading is an issue, not sure how much they check, but I don't think they care about CM7 off a SDcard not working!
Everything looks perfect on that card. All the right files, partition sizes, etc. You have stock on emmc, CWM 3.2.0.1 on emmc recovery.
I still suspect hardware issues. Powering off makes card semi-unreadable. Can still boot to it but when checking for partition information on SD fails.
If you registered your nook, the serial number is all you need. Refurbished usually have a one year warranty. Mine did. Just tell them card reading is intermittent. Which it is. They are pretty generous. You still have stock on there.
Edit: Try just an ordinary SD and power off, reboot, and repeat many times and in between check card reading ability.
leapinlar said:
Everything looks perfect on that card. All the right files, partition sizes, etc. You have stock on emmc, CWM 3.2.0.1 on emmc recovery.
I still suspect hardware issues. Powering off makes card semi-unreadable. Can still boot to it but when checking for partition information on SD fails.
Click to expand...
Click to collapse
Yup, it's really the only thing that hasn't been able to be changed through all of this.
I've mostly gotten these results - I've managed to make it worse as I redid things and apparently got sloppy. But when going back to methodically following instructions I have what I had months ago. I had hoped buying other cards would make it at least act differently.
Thanks for all of the reviews and double checking, at least I now it's not something obvious (but wasn't obvious to me) that I missed along the way!
I'll have to call B&N and see how strict they are and if they take the "It just has trouble reading any SD card consecutively".
Now where was that review of the Nexxus 7.... and I wonder how all the tablet prices are going to drop especially for the Galaxy Tab. Buying is not as fun but I am completely beat with modding failures.
We are too fast with each other. Lol. See my edit above.

[Q] Having trouble creating bootable sd card

Hi xda, my nook won't boot up at all after I tried to restore to stock from autonooter 1.01. I read as many threads as I could and tried to make a bootable sd from leapinLar's tips page. The stock recovery with cwr and without. I used winimage and win32. With winImage I get an error "reading from file". win32 seems to write the file but it doesn't boot up the nook. When I try and open the sd with windows to see if anything is on the sd it says "not formatted would you like to format it now". I downloaded file, unzipped, then wrote to sd. I must be doing something wrong creating the sd but I can't find any info as to what. Thanks for any help
Stjpa said:
Hi xda, my nook won't boot up at all after I tried to restore to stock from autonooter 1.01. I read as many threads as I could and tried to make a bootable sd from leapinLar's tips page. The stock recovery with cwr and without. I used winimage and win32. With winImage I get an error "reading from file". win32 seems to write the file but it doesn't boot up the nook. When I try and open the sd with windows to see if anything is on the sd it says "not formatted would you like to format it now". I downloaded file, unzipped, then wrote to sd. I must be doing something wrong creating the sd but I can't find any info as to what. Thanks for any help
Click to expand...
Click to collapse
Are you unzipping the right file? You said something about with stock recovery and without. Those are not image files that can be burned. When you unzip my image zip file, you should end up with a 300MB .img file. That is what you burn with win32diskimager. And take the card out of the PC and put it back in before you try to look at it. And be sure to use an external card reader, not one built into your PC.
Sent from my Nook HD+ using Tapatalk
Thanks Leapinlar. I downloaded your nook color emmc stock recovery zip with and without the cwr. I am using external sd reader. I downloaded and tried cwm-6.0.1.2 bootable sd zip and tried that in the nook and nothing happens. Also tried the 5.5.0.4 version too. I removed the card reader and reinserted it in the pc and when I click on the drive letter it ask me if I want to format it. I used win32diskimager and it said write successful, so I put it in the nook and then plugged nook into computer with the stock usb cable and nothing happens. If I hold the power button down the pc does ding as if when you plug in an external device. I'm either trying to burn the wrong file or I'm not making the bootable. Thank you for your help.
Stjpa said:
Thanks Leapinlar. I downloaded your nook color emmc stock recovery zip with and without the cwr. I am using external sd reader. I downloaded and tried cwm-6.0.1.2 bootable sd zip and tried that in the nook and nothing happens. Also tried the 5.5.0.4 version too. I removed the card reader and reinserted it in the pc and when I click on the drive letter it ask me if I want to format it. I used win32diskimager and it said write successful, so I put it in the nook and then plugged nook into computer with the stock usb cable and nothing happens. If I hold the power button down the pc does ding as if when you plug in an external device. I'm either trying to burn the wrong file or I'm not making the bootable. Thank you for your help.
Click to expand...
Click to collapse
You don't say, but you are unzipping those image files before you burn them, right? Should be 300MB .img file. Other than that just look at my A10 tip in my tips thread and follow exactly.
Sent from my Nook HD+ using Tapatalk
leapinlar said:
You don't say, but you are unzipping those image files before you burn them, right? Should be 300MB .img file. Other than that just look at my A10 tip in my tips thread and follow exactly.
Sent from my Nook HD+ using Tapatalk
Click to expand...
Click to collapse
Yes I did unzip the image file before I burned it. I ended up finding a cwr zip that was for a 4 gig card, probably an older way of doing it, and that worked for some reason. I did use your stock 1.4.3 zip though and all seems well. Your tips page is great, thank you, you're very helpful now I can play around and brick it again with some other stuff.
Hey guys.
I am somewhat a noob. I bought a brand new 8gb nook color from wallmart on black friday. I heard about how you can put CM onto the sd card and boot from that without altering the device itself. I have tried for HOURS to do this. I have looked up COUNTLESS walk throughs and done everything they say, done alternations, and used different cards ranging from 2gb sandisk (class 1?) to 32 gb sandisk this is a class 4. I've used winimage and burned the image to the card, then dragged over cyanogenmod and done this task in countless different ways. Every time I shut down the nook, put in the card, then re-boot, the nook does NOT boot from the card. It boots normal, then I can actually browse the card after it boots up. I have done it EXACTLY how it says here and read tutorials so its not a question of whether or not I have followed standard proceedure. My firmware version is 1.4.3. Ive searched online to this and to no avail. My sister bought the exact same one at the exact same time and it does not boot the sd either. I have done about 8 straight hours of research on this guys, so I'm no pro but I have a basic understanding of how it works now. My questions are this:
1: Did Barns and Noble put restrictions on the newest nook color or on the newest software version? And if so is there a way around this?
and
2: If NOT, is there an alternate way/installation onto the card that I can do (such as an image pre loaded with CM etc.) that I might be able to try instead of the conventional way?
Thanks guys! Sorry for the uber long post : S
ronin8knight said:
Hey guys.
I am somewhat a noob. I bought a brand new 8gb nook color from wallmart on black friday. I heard about how you can put CM onto the sd card and boot from that without altering the device itself. I have tried for HOURS to do this. I have looked up COUNTLESS walk throughs and done everything they say, done alternations, and used different cards ranging from 2gb sandisk (class 1?) to 32 gb sandisk this is a class 4. I've used winimage and burned the image to the card, then dragged over cyanogenmod and done this task in countless different ways. Every time I shut down the nook, put in the card, then re-boot, the nook does NOT boot from the card. It boots normal, then I can actually browse the card after it boots up. I have done it EXACTLY how it says here and read tutorials so its not a question of whether or not I have followed standard proceedure. My firmware version is 1.4.3. Ive searched online to this and to no avail. My sister bought the exact same one at the exact same time and it does not boot the sd either. I have done about 8 straight hours of research on this guys, so I'm no pro but I have a basic understanding of how it works now. My questions are this:
1: Did Barns and Noble put restrictions on the newest nook color or on the newest software version? And if so is there a way around this?
and
2: If NOT, is there an alternate way/installation onto the card that I can do (such as an image pre loaded with CM etc.) that I might be able to try instead of the conventional way?
Thanks guys! Sorry for the uber long post : S
Click to expand...
Click to collapse
No nothing was done by B&N. It is how you are burning the card. It will not boot in the nook unless burned perfectly. Look at my tips thread linked in my signature and read items A9 and A10.
There not any easy was not to use a bootable recovery card. Just keep trying, using different software, different cards, different PC s, different card readers.
Sent from my Nook HD+ using Tapatalk
ronin8knight said:
Hey guys.
I am somewhat a noob. I bought a brand new 8gb nook color from wallmart on black friday. I heard about how you can put CM onto the sd card and boot from that without altering the device itself. I have tried for HOURS to do this. I have looked up COUNTLESS walk throughs and done everything they say, done alternations, and used different cards ranging from 2gb sandisk (class 1?) to 32 gb sandisk this is a class 4. I've used winimage and burned the image to the card, then dragged over cyanogenmod and done this task in countless different ways. Every time I shut down the nook, put in the card, then re-boot, the nook does NOT boot from the card. It boots normal, then I can actually browse the card after it boots up. I have done it EXACTLY how it says here and read tutorials so its not a question of whether or not I have followed standard proceedure. My firmware version is 1.4.3. Ive searched online to this and to no avail. My sister bought the exact same one at the exact same time and it does not boot the sd either. I have done about 8 straight hours of research on this guys, so I'm no pro but I have a basic understanding of how it works now. My questions are this:
1: Did Barns and Noble put restrictions on the newest nook color or on the newest software version? And if so is there a way around this?
and
2: If NOT, is there an alternate way/installation onto the card that I can do (such as an image pre loaded with CM etc.) that I might be able to try instead of the conventional way?
Thanks guys! Sorry for the uber long post : S
Click to expand...
Click to collapse
Use win32diskimager instead and use an external card writer. The image is approximately 300mb with the Rev5 file. Then copy the CM10 and 2021011 GApps zips to SD card. Insert in Nook Color. Wait for setup to finish and shut down. Start Nook. Enjoy.

Categories

Resources