CSD-Line Modem connection to a home-pc (hermes) - Networking

good morning everybody
i've got a networking question for you: i followed this guide: MDAC - Home connection (sorry for posting it in german).
basically it describes the following essential things:
setting up the modem on my home computer to accept incoming calls
actually i opened a terminal on COM2 which is my modem-port and tested it by calling the modem from my mobile phone via voice-connection. the terminal displayed: RING RING RING RING ... etc.
so i set up my hermes: changed CSD-linetype to 9600(v.110) and the mode to: non-transparent.
set up a new modem connection with the number of my target modem and tried both version, with login credentials and without... (in fact i got the same problems in both tries)
as i have set up everything correctly i tried connecting my hermes via the new modem connection to my modem-computer, but after three tries the hermes gave up and told me: could not connect to...
looking into my modem-terminal: nothing... not even a ring...
so i must assume: my settings are incorrect, do you have any clue?
or has anyone else tried such a connection before?
hope for some replies.
greetings
garfield

CSD connection is a bit hit and miss in recent HTC devices.
Yes, it's definitely a device problem rather than a carrier one - the receiving modem indeed never rang.
If you have patience, try redial a couple of times. I got one out of ten that got through.

hmm, might this be fixed by flashing a newer, or even an older, radio rom?
so i will try to redial, maybe i will get a connection after a few hundred tries
thanks for reply, i thougt i set a setting completly wrong, although there aren't much.
greetings

I thought a radio flash would help too - but I was wrong. I proved it myself.
I recently flashed my machine (Trinity) from WM5 to WM6 and probably will give it another try if I got some spare time. I wish it get fixed - but it's just a wish...

Related

Using as general modem via TAPI (or RIL if need be)

I am trying (unsuccessfully so far) to develop a program that will create a data (modem) connection to a modem connected to any other phone. I then want to transfer a small file using xmodem.
I have done extensive searches and tried solutions with TAPI calls based on samples I have found. I can dial the number of my laptop from the i-mate and the laptop on my desk rings. I tell it to pickup the line (ATA) and it does, but there is no "LINECALLSTATE_CONNECTED" from the "lineInitialize" callback function on the imate. All I get is a "LINECALLSTATE_DISCONNECTED" with the type as "LINEDISCONNECTMODE_UNREACHABLE". finally the it all hangs up, no connection.
I seem to be banging my head against a wall at the moment. There must be many of you out there who have done this or very similar.
I can post source is you want that type of thing, but I dont expect anyone to debug my app, but any pointers or others experiences are appreciated. I have come across the RIL interface, but I get the impression that TAPI is the "correct" way.
Thanks in advance.
Frustrated...
Have you got data enabled on your SIM. I was also banging my head against a wall until I thought I would check that with my service provider. There are 2 data things they can enable, one is fax but there is also data. Without data enabled you will never get a sucessfull modem connection.
arrhh!.. that's is. lol. I knew it would be something silly. Ill call today.
Thanks also. God bless you.
Well sorry to say that was not the issue, I still only get repeated
"LINEDISCONNECTMODE_UNREACHABLE"
errors. I am starting to wonder if I am just getting really bad lines. Can someone who has made a modem connection from the PPC to a desktop modem please post their experience on how reliable it is and what type of connection speed it should connect at (9600? 1200? 300? any connection?).
Is their any working sample code for creating a data connection from the PPC using the TAPI?
I will be happy to publish the code to the small project I am doing so future developers have something to work from as I havent been able to find a working example so far. (when it works that is)
Any help appreciated.
Thank-you
Figured out why it would not connect, for anyone else who has similar problems. Mine was the "CSC Line Type" option in the connection settings area.
It was set to "9600 v110" and "Non-transparent".
Im in australia, I understand the v.110 is the american standard, I changed it to
"9600 v.32" and "Non-transparent" and it connects fine. (dont you hate this type of bug)
Im still unsure what the "Transparent" and "Non-transparent" are todo with, if anyone could expain it would be appreciated.
I am glad you got it working. So I guess your code must be OK. I did not set any special communication mode so I guess that my XDA must of been set correctly anyway. It seems sensible that you are supplied with a setup for the country your device is meant for. I say this is bad of the provider.
How do you get to this setting ? I can't even seem to find it on my XDA. I have got a CSD setting that has a choice of 'Analogue' or 'ISDN' mode, mine is set to 'Analogue'.
I did post some code on this forum that is cut from an application I wrote, have a look at
http://forum.xda-developers.com/viewtopic.php?p=7857&highlight=#7857
Cheers
Paul
The code actually worked almost first time when I had all the connection settings right. Ive got the XModem transfer working now also.
The "CSD Line Type" on my device (an i-mate) is an icon in the setting connection tab. In the same tab there is also
"Beam" - allows you to turn on recieve all incoming beams
"Bluetooth" - on/off/discoverable and bonding
"Connections" - normal connection setup
"GPRS Settings" - PAP/CHAP auth and class 8(4RIT)/class 10(3R2T)
not sure what the different GPRS settings are for either, but that side seems to work.
Hey to you all,
I'm trying to set up a CSD connection via RIL , AT commands and TAPI!!! You seem to have accomplished the TAPI solution which i have not started yet, could you advice me on the necessary TAPI functions to use in order to make this work ?
Any help would be very appreciated. Thanks to all.
Have you seen this link?
http://forum.xda-developers.com/viewtopic.php?t=1716&highlight=csd

people with GPRS problems...

I am one of those users that is having trouble connecting to GPRS more than once and getting the "unknown reason" problem. Only a soft reset or turn on/off flight mode will fix it. Well I found out what is causing this, at least for my device. I am running Wisbar Advance on mine and is what causing the problem. Once I closed the app, I can connect/disconnect GPRS as I please. I made calls in between also and it still works...
The developer for Wisbar is working on this issue so hopefully he will get this fixed. In the meantime, I have turned off Wisbar..
Hope this is what causing u guys' devices also.
Great info! Just a heads up. I had this problem since I upgraded to the 1.06 ROM however I have never installed Wizbar Advance. The only thing that I could get to fix it was upgrading to the Norwegian 1.11 ROM version or using the 1.10 US Radio stack. Even the Finish 1.11 did not fix the problem.
-Mashie
I have the problem and I'm not using Wisbar. I guess magician_os1.11wwe_bigstorage_6.zip is based on the Finnish ROM?
You can add another application to the list of problem apps (at least this worked for me)
Sygic .mobile contacts seems to mess up GPRS as well.
I've been using the 1.06 WWE rom, and i tried anasky's 1.11 bigstorage rom, and both times, with .mobile contacts installed, i received the "cannot connect for an unknown reason" error, after uninstalling it, GPRS reconnects fine everytime.
Hope this helps some of you.
i changed my sim card to a new one and now i don't get that error. plus i believe that part of that error is the service provider.
hope that helps
I have Qtek 1.11 and same problem too
It is a real pain, I do not have Wisbar, and I can only connect once then need a reset. Any ideas out there?
One cheap solution is to put the phone in flight mode and then go back to reset the GPRS. Not very smooth, but at least better than having to soft reset.
Loboman said:
One cheap solution is to put the phone in flight mode and then go back to reset the GPRS. Not very smooth, but at least better than having to soft reset.
Click to expand...
Click to collapse
I have tried to turn flight modem on/off but i still get the error
"dialed:isplnk1.swip.net. The answering modem has disconnected. To check your connection settings and change them if needed, tap settings"
Does ne1 know what I can do? so I can use my gprs again. it worked fine just a day ago, and I havent done anythin at all that could cause this problem
I don' t have a magician but a blue angel.
I've got the same problem.
It's the last built of IA Caller ID.
I've make a hard reset with no IA Caller and no problem again.
just double check the settings to make sure that the access point name shows up in the number section of the connection settings, when its not there that can cause the answering modem problems
rgds
j
I have 2 SIM Cards with the same number, one for the QTek 2020, and one for a Motorola mpx200.
If they are both switched on, then my GPRS is disconnected after about 15 minutes, and I can only reconnect by going in and out of flight mode.
If I switch the Motorola off, then I stay connected, and can disconnect
and reconnect properly.
Eddan said:
Loboman said:
One cheap solution is to put the phone in flight mode and then go back to reset the GPRS. Not very smooth, but at least better than having to soft reset.
Click to expand...
Click to collapse
I have tried to turn flight modem on/off but i still get the error
"dialed:isplnk1.swip.net. The answering modem has disconnected. To check your connection settings and change them if needed, tap settings"
Does ne1 know what I can do? so I can use my gprs again. it worked fine just a day ago, and I havent done anythin at all that could cause this problem
Click to expand...
Click to collapse
Never had that error message. Only the one hamsup1o was talking about. Is the Norwegian 1.11 Ananskyfied yet? I want to test if the problem is fixed in that one.
For me, I don't think it's any one piece of software. Since I upgraded my Jam last weekend to 1.11, it continually disconnects from GPRS. Soft resets may or may not correct the problem on the first try so a second reset is in order. Trying to turn Flight Mode On/Off is a chore in itself. I may need to tap "Turn Flight Mode On" several times before it finally does it. Even when GPRS is connected it will only last 5 minutes. Then while still connected, going to a different webpage, says that webpage cannot be found. Very freakin' frustrating!! :evil:
So, today at work I backed everything to SD and did a Hard Reset. I then cancelled out of the Operator settings, but allowed the other apps to install and soft reset. I manually added my data settings and connected. Within two minutes I lost my connection. Reset the device and couldn't connect. Reset again and it's fine. It's hit or miss. Restored from backup. Gave a MS Voice Command error so deleted that. Several resets later on the train ride home and it's been fine ever since, for now!
The question is, could this be a T-Mobile problem? I called them yesterday and all they could tell me is that data outages in the Boston area may occur in the evenings due to upgrades. Perhaps it's just a coincidence that I did the ROM upgrade and TMo is acting up. I'm pulling hairs here!!
smfa1965 said:
For me, I don't think it's any one piece of software. Since I upgraded my Jam last weekend to 1.11, it continually disconnects from GPRS. Soft resets may or may not correct the problem on the first try so a second reset is in order. Trying to turn Flight Mode On/Off is a chore in itself. I may need to tap "Turn Flight Mode On" several times before it finally does it. Even when GPRS is connected it will only last 5 minutes. Then while still connected, going to a different webpage, says that webpage cannot be found. Very freakin' frustrating!! :evil:
So, today at work I backed everything to SD and did a Hard Reset. I then cancelled out of the Operator settings, but allowed the other apps to install and soft reset. I manually added my data settings and connected. Within two minutes I lost my connection. Reset the device and couldn't connect. Reset again and it's fine. It's hit or miss. Restored from backup. Gave a MS Voice Command error so deleted that. Several resets later on the train ride home and it's been fine ever since, for now!
The question is, could this be a T-Mobile problem? I called them yesterday and all they could tell me is that data outages in the Boston area may occur in the evenings due to upgrades. Perhaps it's just a coincidence that I did the ROM upgrade and TMo is acting up. I'm pulling hairs here!!
Click to expand...
Click to collapse
I have the exact same problem with my Jam on T-Mobile (in Colorado) however it seems to have gotten better with the 1.11 ROM. The strange thing is that it does not ever happen with my 6315 on T-Mobile. I have spoken with their customer services serveral times and we have tried a few different things. The last thing we tried was a brand new SIM card to remove that as a posible problem. Since doing that, I can stay connected to GPRS, take calls and it re-connects with out me doing anything and it seems to have helped.
I have not tried to see if there is any change between wap.voicestream.com or internet2.voicestream.com. Which are you using?
I have the same problem with GPRS and the Cannot connect for an unknown reason. It initially connects fine, but if I disconnect it manually, I cannot reconnect without the soft reset. I started getting this error when I upgraded to 1.11WWE last night. I went back to Version 1.06WWE and the problem was gone so it is defiantely a ROM problem. Imate's Customer "Dis"-Service continues to timeout everytime I go online with them. I am in the process of trying the UK 1.11JAM Rom to see if that makes any difference. I am with T-Mobile USA.
On the Club I-mate forum there are people with this problem as well and one of them is on Cingular!!! So it's not carrier specific.
__________edit
I tried the UK 1.11 ROM and it worked a bit better. There was even a new tab in the GPRS bubble that you could click to disconnect the GPRS rather than holding down the red phone button. But alas, I still got the Cannot Connect for an unknown reason mesage. I'm going back to 1.06 (Thankfully I backed it up) It worked fine. Is anyone having this problem with the Anansky hacked ROM?
Also, why does the UK version come with Skype and the WWE version doesn't?
Could it be due to Activesync?
I too have the GPRS problem, usually it occurs after synchronizing with the PC. The flight mode trick fixes it. I can repeat this behavior and can always fix it, so it remains a nuisance...
Since you can access the internet through Activesync, maybe the OS stays locked in that mode and does not allow for GPRS to be a valid network connection...
Anybody else have similar symptoms?
Mashie, I use internet3.voicestream.com. As you said nothing seems to help.
chinadan, Yes! I had the exact same thing happen to me last night. I've been tinkering with my Jam for the last week trying to get it to work. Last night it was working fine, but then I connected it to my desktop to load PHM Registry and when I disconnected, GPRS started flaking out! Performing a soft reset didn't help.
I've been going back and forth with i-Mate CS, and it's obvious they know there's an issue. They seem to be getting a little testie since I'm basically telling them I'm not an idiot so please get the crap fixed! They had the nerve to send me instructions on how to setup a GPRS Connection on the Jam! :twisted: What nerve!
Anyway, think I'll try loading the worldwide 1.11WWE and see what happens. Anyone have a backup of 1.06 US 850 ROM?
Thanks and cheers!
Well, I went almost 24 hours without a GPRS problem on my JAM yesterday. I didn't get the usual "Cannot connect for an unknown reason" error message. This time I got a message saying that there was a problem with the modem???? I don't know where that one came from... changed my gprs setting to internet2.voicestream.com and it works now....until the next error message.
Screw it. I'm going back to 1.06. The JAM is VERY sluggish now and I can't even get it into flight mode to correct the problem. I guess I'll wait for the patch. (It seemslike we spend most of our time waiting for a patch or an update of some kind. ARGGGHH!)
ALso, I don't know if this was the case with the 1.06 ROM, but I used to have to hold down the red phone button for a few seconds to get the GPRS to disconnect. But with the 1.11UK rom all it takes is for you to click the red phone button and the connection is dropped. Example: If I'm on the Today Screen with GPRS connected, click the red phone button and voila, gprs is disconnected. Is this normal? I don't remember it disconnecting so easily with 1.06.
Also, saw this over on the HoFo: ___________________
New HTC Galaxy and Wizard to replace the Magician.
Got a hirizontal slide out keyboard. Same size as Magician. Black in colour. with 128mb ram, Wifi built in. Same size as Jam. With a 2.1mb camera (undecided maybe 1.2). Just saw the pictures, but it looks awesome. (I think it also had edge).
johnannie said:
Also, saw this over on the HoFo: ___________________
New HTC Galaxy and Wizard to replace the Magician.
Got a hirizontal slide out keyboard. Same size as Magician. Black in colour. with 128mb ram, Wifi built in. Same size as Jam. With a 2.1mb camera (undecided maybe 1.2). Just saw the pictures, but it looks awesome. (I think it also had edge).
Click to expand...
Click to collapse
Any chance you give us a link to those pics? Pleaseeeeeeee :twisted:
Ok, been tinkering around this evening concerning the GPRS connection issues and this is what I have thus far. First, Club IMate has new Operator Settings on their website. One of their techs was kind enough to e-mail it to me this afternoon and checking their website this evening shows T-Mobile ver1.6. Applied those settings and it seemed to do a better job at installing my VPN settings for internet3.voicestream.com. However, when I checked the Connections screen it listed My Isp with my VPN connection and My Work Network was setup for wap.voicestream.com. Ok, nice but I don't use the wap settings. Connecting through IE to wap.yahoo.com resulted in the TMo Wap connection to launch, but not my VPN connection. So I went back into Connection settings and set both Work and Internet to "My ISP". Upon doing this and selecting any website from IE, it wouldn't connect and give me the error "Make sure you have your modem installed blah, blah, blah". If I then press and held on the "G" and tapped connect, it connected just fine.
So that got me thinking about the Registry again and why in the Connection screen for both Internet and Private network, why there was no option for "The Internet", or "My Secure WAP" so forth and so on. When I had my XDA IIs, those where options. So I loaded PHM Registry to the device and went exploring. The first thing I found and deleted was in: \HKLM\Software\HTC\WModem. I deleted the Preset GPRS key. The next thing I found where all the Interent settings I just mentioned in:
\HKLM\Software\Microsoft\ConnMgr\Destinations\. There is listed "The Interent" (which I tried to create myself in Connections but it said it already existed) and My Secure Wap plus others that I had made. So for starters I deleted "The Internet" key and reset the device.
Went back into Connections and created a new network called The Internet and added my connection to internet3. I then switched it to only look at The Internet network. Launching IE again and trying to go to wap.yahoo.com. Again, I get the "Unable to Connect: Ensure that your modems are presentand inserted correctly, and no network card present".
So obvioulsy, my edits to the Registry made little difference. So again that got me thinking. Why would their be a WAP connection when I selected T-Mobile VPN during the new cab installation? Because it needs it!
I then went back into the Network Management screen under connections and left it set to The Internet for programs that auto connect to the internet and set it to My Work Network for the private network option. Since doing this I've had no issues when any connection while browsing. If I go to a WAP site it automatically connects to T-Mobile WAP connection. If I then decide to go to a full blown HTTP website, it automatically stops the WAP connection and launches the VPN one. There is no delay when it does this, well, maybe a second! :lol:
My thinking is (and, I'm no programmer or Registry master!) that the problem lies in the Registry settings for IE. Perhaps it runs deeper than that but if one of you Guru's could take a look perhaps we can get this ironed out once and for all. Thanks for listening!

Problem with Wizard -> GPRS and receiving calls

Dear technically gifted people,
I have recently purchased the Wizard (i-mate k-jam) and have the following three problems:
1. Sometimes the phone does not receive calls and they go directly to voicemail, even though I am in an area where all mobiles work and the phone shows full reception.
2. If reset the device or turn on/off flight mode, the device has no problem connecting to GPRS/EDGE (provider MTS/Russia), but after some time it drops the connection and cannot reconnect until next reset.
3. Flight mode switch does not always work. Have to turn it on 2-3 times before phone responds and turns the phone back on.
If someone would be kind enough to help me resolve them I would greatly appreciate it. I recently upgraded to the new ROM (the one posted on the clubimate site in March) but it did not seem to help the issue.
Regards,
egrib
i have the same problem! Have to turn it off and then back on again, very annoying!
Do you think turning the voicemail off will sort it out? I dont really have any need for it anyway
could be SIM related.
My wizard showed the same instability. I needed to reboot every night otherwise i would get dropped calls (straight to voice mail) no GRPS access, and the charging wouldn't work. I changed roms etc. What finally did the trick for me is I got my service provider (FIDO in canada) to change my SIM from the 2001 card i had to a current one.
It seems to have done the trick.
From my own experience and from seeing all the posts on this forum it seems like this device is full of bugs and is just not worth the time and money.
As there a similar device out there that actually works and people have no problem using?
Thanks.
egrib said:
1. Sometimes the phone does not receive calls and they go directly to voicemail, even though I am in an area where all mobiles work and the phone shows full reception.
Click to expand...
Click to collapse
did you have the same problem with previous handsets in the same area? such problem are quite often caused by network issues not mobile and you should try reporting it to your operator's customer care. however, if such problem persist only on wizard and in various areas, then it's probably problem with mobile...
egrib said:
2. If reset the device or turn on/off flight mode, the device has no problem connecting to GPRS/EDGE (provider MTS/Russia), but after some time it drops the connection and cannot reconnect until next reset.
Click to expand...
Click to collapse
you mean [G] icon on top of screen? well, this is a feature of this model, that after some time it detaches from GPRS, so [G] icon disappears. however if you'll try to connect to internet through GPRS, it will attach again and connect, so i wouldn't be so much concerned about it.
egrib said:
3. Flight mode switch does not always work. Have to turn it on 2-3 times before phone responds and turns the phone back on.
Click to expand...
Click to collapse
i've had the same problem, but i noticed that it just needs a bit of time for phone to switch on again. so when you're trying to switch off flight mode, tap it once and wait a bit. it should turn on after a while. at least it works this way with me..
eva_d,
I think you are entirely correct on point 3 - flight mode switch takes some time.
As for the other points, I don't think they are as easily resolved. When the phone does not receive phone calls (and calls go straight to voicemail) it does not seem to be a carrier problem since 1. i never had this problem with the same card in a different mobile and 2. once it stops receiving calls it continues to do so until a reset, regardless of where I am located.
The GPRS issue - i know what you are referring to with regards to the [G] icon (I have it all the time) but once i receive or make a phone call, I cannot reconnect to the internet until i reset the device. Also not a carrier problem. This seems to be an issue with all MTS users in Russia. So far unresolved.
Anyone other ideas anyone? Thanks
It's well known issue (GPRS on MTS Moscow; is your mts is in Moscow?). It was fixed in new ROM, that just was released week ago. Russian version is available.
eva_d said:
egrib said:
1. Sometimes the phone does not receive calls and they go directly to voicemail, even though I am in an area where all mobiles work and the phone shows full reception.
Click to expand...
Click to collapse
did you have the same problem with previous handsets in the same area? such problem are quite often caused by network issues not mobile and you should try reporting it to your operator's customer care. however, if such problem persist only on wizard and in various areas, then it's probably problem with mobile....
Click to expand...
Click to collapse
I have a kindoff similar problem. Just got my Qtek yesterday and I tried latching to cingular. What happens is when I switch on the phone, it takes forever to latch to the network. I see the
Y.
Y..
Y... going on for ever. In my old phone, just switch it on and there it connects to cingular. I tried doing the manual/automatic network selection and everything but it just takes too much of time to latch on. It finally latches (thank god !) but still its annoying. But once connected, itnever drops off or goes to voice mail. Looks like it has a starting problem
Also, reception wise, it shows less bars then my old phone when I am sitting on the same chair :?
Did anybody face the same problem, or am I the blessed one. Any tweaks or something that can be done ?
I also have problems sometimes connecting to edge/gprs, I think it might have something to do with handshaking accross towers.
I noticed that this happens when I enable TOMTOMTRAFFIC, it will get the traffic the first time I start tomtom, then 15 minutes into driving when it trys to get a traffic update it will not connect to gprs, it will keep dialing and eventually disconnect. Then after a rest, it will connect again but again after about 15 minutes of driving it has the same problem. Pretty annoying.
Vishny,
I am indeed on Moscow MTS. You mention a new ROM that fixes this - are you referring to the ROM that came out early this year (2.16.9.1) ? If so, I did the upgrade (english version) and it did not seem to help. If there is something more recent that fixes the MTS problem, please let me know where I can download it.
Also, are you having and problems with receiving calls? Thanks.
egrib said:
Vishny,
I am indeed on Moscow MTS. You mention a new ROM that fixes this - are you referring to the ROM that came out early this year (2.16.9.1) ? If so, I did the upgrade (english version) and it did not seem to help. If there is something more recent that fixes the MTS problem, please let me know where I can download it.
Also, are you having and problems with receiving calls? Thanks.
Click to expand...
Click to collapse
It's 2.18 ROM with new 2.20.11 radio rom. I'm having no problems with calls or GPRS. Now my device is perfect, I love it. Just try it, you can find it here:
ftp://ftp.xda-developers.com/Uploads/HTC Wizard/ROMS/
Thanks vishny - if that will indeed solve the problem.
Few questions, are there any other places to get the files (i am having problems logging into the one you provided).
Also, is this only for a Russian OS or do they have the same for english? Thanks
Guys, could you please advise me how can I download from FTP? It asks for username & password, but my profile's username and passwords wont work.
fmraven said:
Guys, could you please advise me how can I download from FTP? It asks for username & password, but my profile's username and passwords wont work.
Click to expand...
Click to collapse
user/pass: xda/xda
eva_d said:
fmraven said:
Guys, could you please advise me how can I download from FTP? It asks for username & password, but my profile's username and passwords wont work.
Click to expand...
Click to collapse
user/pass: xda/xda
Click to expand...
Click to collapse
Great! Thanx a lot.
And another question. Would QTEK ROM work for K-Jam, or should I wait for official K-Jam ROM update?
fmraven said:
And another question. Would QTEK ROM work for K-Jam, or should I wait for official K-Jam ROM update?
Click to expand...
Click to collapse
it will work, but you need to unlock your device first with Lokiwiz or aWizard. search forums, there are lots of posts regarding this.
Thanks for all the help.
One question to Vishny and others - i see the new 2.18 rom update in Russian - does anyone have any idea where I can get it in english?
I assume the GPRS/calls problem lies in the Radio ROM - so another question may be how can i keep my english ROM but update my Radio ROM to one that would work with MTS in Russia?
Many thanks
egrib said:
Thanks for all the help.
One question to Vishny and others - i see the new 2.18 rom update in Russian - does anyone have any idea where I can get it in english?
I assume the GPRS/calls problem lies in the Radio ROM - so another question may be how can i keep my english ROM but update my Radio ROM to one that would work with MTS in Russia?
Many thanks
Click to expand...
Click to collapse
There is no english 2.18 rom, because 2.18 solves specific problem with one of operators in Moscow. Some guys make hack, they flash 2.16 i-mate or 2.17 qtek english roms, then flash 2.20.11 "russian" radio rom and then install additional RadioDriver_GPRSStall_Wizard_Mar24.CAB they extract from extrom of 2.18 russian rom.
Look at this:
http://www.qtek-mobile.ru/forum/viewtopic.php?t=2131&start=30
vishny,
i installed the new radio rom onto the latest english i-mate rom and thw wizard finally worked with MTS in Russia without any problems. For that I thank you.
Unfortunately now for some reason once in a while the screen goes dark (as if the device is sleeping, the light is still blinking) and the only thing I can do is reset the device. Any ideas?
Thanks
p.s. why does this thing always have problems and as soon as i solve one, another arises :?

odd GPRS problem

Hi,
my GPRS connection is working, it connects without any problem but when i try to navigate with PIE then I can see the message "Opening" on the left lower corner but it just stays that way for a long time and the page never gets displayed. My e-mail works fine so that means i have GPRS connection and working. If i try navigating to a WAP site some pages get displayed and some other don't. If i connect via WiFi or via activesync then i can navigate without any problems. Based on my observations I suspect a problem with the MRU (Maximum receive Unit) of the TCPiP stack but i can not find on the registry where to change that.
Hope someone can help.
I used Tweak2K2 to set it in mine. Sorry I do not know the Reg setting.
hguiraud said:
Hi,
my GPRS connection is working, it connects without any problem but when i try to navigate with PIE then I can see the message "Opening" on the left lower corner but it just stays that way for a long time and the page never gets displayed. My e-mail works fine so that means i have GPRS connection and working. If i try navigating to a WAP site some pages get displayed and some other don't. If i connect via WiFi or via activesync then i can navigate without any problems. Based on my observations I suspect a problem with the MRU (Maximum receive Unit) of the TCPiP stack but i can not find on the registry where to change that.
Hope someone can help.
Click to expand...
Click to collapse
I wonder whether your HTTP proxy port number is correct. I had same problem and I was using the advertised port number until I discovered there was another one that actually worked. I would suggest a port number but I'm O2 UK (it was `advertised as 80 but only actually worked on PIE with 8080)
Mike
You are not alone
Please check the following threads, both are related to our problem, unfortunely none of them gives a solution.
http://forum.xda-developers.com/showthread.php?t=286449
http://forum.xda-developers.com/showthread.php?t=287101
My GPRS connection doesn´t require an HTTP proxy server so Mike´s suggestion didn´t work for me. I contacted Movistar and they are not open to give support since I didn´t buy the device from them....
On the other hand, if somebody can provide the ROM reg settings and a brief instruction on how can be changed would be great
Hi Luiggi
Sorry you have not got it solved yet. I remembered your post and looked for it but did not find it - hoped you had a solution to offer - sadly not
Edit: I suppose you are certain about the proxy? I ask because mine will connect to GPRS just fine without it - BUT PIE does not unless it's set.
Mike
Maybe it is a Movistar problem
Interesting, so happens that my service provider is also Movistar; maybe they have done something different to their network settings. Any way, I was in the US recently and was able to use GPRS roaming although because the TyTN does not differentiates between GPRS and EDGE it could have been that it was using EDGE and that it why i could navigate using PIE.
The funny thing about this problem is that my e-mail works fine and my SPB whether also updates without problems, it is only the navigation with PIE that i have issues with. Based on my observations it seems to be that if the tcp packet is larger that a certain size it gets dropped by the tcp stack.
Not lucky so far
Hi Mike!
Movistar people told me that the don´t need proxy servers for the connections since they use Dynamic IP addresses (?). I´ve have tried a lot of different configurations but not luck so far, the comment posted above could be they key, now the big question is: What are the proper settings and how to modify the reg...?
Will reflashing the phone be the only solution?
Well looks like the options are narrowing down to reflashing the phone.... I'll give it a couple of days more to see if someone can give Us a hint on what to do.
hguiraud said:
Well looks like the options are narrowing down to reflashing the phone.... I'll give it a couple of days more to see if someone can give Us a hint on what to do.
Click to expand...
Click to collapse
I´m not sure about reflashing, actually I have two 8525 I paid to SIM unlock the 1st one so I still have the original ROM 1.34.505.1 and the symptoms are the same, I don´t know what ROM would be suitable to "solve" the problem in case this would be causing the partial lock.
New Finding
I´ve been trying a lot of things and I guess I´m close to the root cause. I strated from scratch with a hard reset and giving a soft reset before the 3 sec secreen of auto configuration, then I tried to set a connection in my ISP, I named it "The Internet" and when I hit the OK button I got a message saying that there was an existing connection setting under the same name!!! I couldn´t find such connection, so I´m pretty sure that the connection is hidden somewhere in the ROM and we need to disable it and create a new one or modify the reg to address a different connection consistent with our own network.... Any thoughts on this?
luiggi said:
I´ve been trying a lot of things and I guess I´m close to the root cause. I strated from scratch with a hard reset and giving a soft reset before the 3 sec secreen of auto configuration, then I tried to set a connection in my ISP, I named it "The Internet" and when I hit the OK button I got a message saying that there was an existing connection setting under the same name!!! I couldn´t find such connection, so I´m pretty sure that the connection is hidden somewhere in the ROM and we need to disable it and create a new one or modify the reg to address a different connection consistent with our own network.... Any thoughts on this?
Click to expand...
Click to collapse
I do have exactly the same problem: an MMS connection is missing but stored somewhere... Anyway to figure out where it is? To me, it's just a flag to change in order for it to re-appear in the \connection\connections tab...
MMS in Cingular
Jeff_mm said:
I do have exactly the same problem: an MMS connection is missing but stored somewhere... Anyway to figure out where it is? To me, it's just a flag to change in order for it to re-appear in the \connection\connections tab...
Click to expand...
Click to collapse
I mapped that one in Cingular, the MMS settings are self extracted from the extended ROM, if you want to get rid of it just do a hard reset and then a soft reset when the 3 sec message shows up, hope this can help you
Please tell us how you did it....
jcb_home said:
I used Tweak2K2 to set it in mine. Sorry I do not know the Reg setting.
Click to expand...
Click to collapse
Yesterday I took a look the the various reg entries and there are some which set default addresses, did you change those addresses? How did you do with Tweak2k2?
8525 on SALE
hguiraud said:
Hi,
my GPRS connection is working, it connects without any problem but when i try to navigate with PIE then I can see the message "Opening" on the left lower corner but it just stays that way for a long time and the page never gets displayed. My e-mail works fine so that means i have GPRS connection and working. If i try navigating to a WAP site some pages get displayed and some other don't. If i connect via WiFi or via activesync then i can navigate without any problems. Based on my observations I suspect a problem with the MRU (Maximum receive Unit) of the TCPiP stack but i can not find on the registry where to change that.
Hope someone can help.
Click to expand...
Click to collapse
I went thru all regs and I couldn´t find MRU or LCP (Link Control Protocol) settings, what disturbes me more is that I put my SIM in my 8125 and everything (IE. messenger, Gmail, Hotmail, etc.) works wonderful!! I think I´ll put on sale my 8525.......
More findings
I do have GPRS connection, no doubt about it. I install Tonaya Iper in my phone and the software gives the ability to trace the route from my phone to the destination, for instance The route to www.gmail.com (216.239.63.19)
is as follows (I set the time [email protected]):
1.- 10.15.14.78
2.- 10.2.4.20
3.- 10.2.4.134
4.- 200.36.174.81
5.- 200.39.31.42 (mx-mesr-rt1.telefonica-data.com.mx)
6.- 213.140.50.233 (So-2-3-1-grtmtyma2.red.telefonica-wholesale.net
7.- Request timed out
8.- 213.140.43.25
9.- 213.140.43.225
10.- 213.140.36.45
11.- 213.140.37.57
12.- 64.233.123
13.- 66.249.94.8
14.- 72.14.233.123
15.- 71.14.233.123
16.- 216.239.63.19 (bp-in-f19.google.com)
When I try to trace the communication with a 1 second timeout the phone stalls for a while in server 213.140.50.233 and makes the traceability extremely slow.
My conclusión is that when the communication reach the server 213.140.50.233 this cause a delay and my phone can not continue to the final destination probably because the pre set delay in the application exceeds its timout parameter.
Any suggestions?
Not a "Maybe" MOVISTAR is guilty for poor GPRS connections!!
hguiraud said:
Interesting, so happens that my service provider is also Movistar; maybe they have done something different to their network settings. Any way, I was in the US recently and was able to use GPRS roaming although because the TyTN does not differentiates between GPRS and EDGE it could have been that it was using EDGE and that it why i could navigate using PIE.
The funny thing about this problem is that my e-mail works fine and my SPB whether also updates without problems, it is only the navigation with PIE that i have issues with. Based on my observations it seems to be that if the tcp packet is larger that a certain size it gets dropped by the tcp stack.
Click to expand...
Click to collapse
Today I use a SIM from the other mexican cell company (telcel), I just enter APN, user name and password and in a blink my 8525 flew thru PIE, hotmail, MS messenger, Gmail and everything!!! Conclusion:Movistar system or set ups are causing all the connection problems, I´ve spent hours in the phone with their wonderful engineers and none of them has been able to explain why Movistar can´t give a decent service to 8525 users.
Using the Traceroute feature of IPer I notice a very long delay to ping the Movistar router located in Madrid (213.140.50.233), there´s where I think the problem is.
You are right Luiggi...!
One of the guys here at the office also has a Dopod 838pro (I'm ussing a HTC TyTN) but with Telcel instead of Movistar...the push e-mail capabilities and the internet surf are really very good ...but with the GPRS of Movistar I recive my e-mails very delayed in the phone and also still unable to sing in to MSN messenger.
Thanks to your post now I know the trut; I was really thinking that maybe the TyTN was the problem (I mean, the HTC branded because the Dopod was functioning just very fine) I was even thinking in return it...
regards
Hummm I suspected that....
Well I think we have (a winner) an answer (partially), I will go back to Movistar and complain, I may not get any results from it but I really have no options since because of my work I travel a lot and the roaming pricing I get with them is way better that the other alternative. The funny thing about this issue is that other HTC phones do not have it. A co worker has a Wizard and he can navigate with PIE. Maybe it would be interesting to investigate what could be the difference or why other phones can navigate and Tytn can't.
Wizard works great!
hguiraud said:
Well I think we have (a winner) an answer (partially), I will go back to Movistar and complain, I may not get any results from it but I really have no options since because of my work I travel a lot and the roaming pricing I get with them is way better that the other alternative. The funny thing about this issue is that other HTC phones do not have it. A co worker has a Wizard and he can navigate with PIE. Maybe it would be interesting to investigate what could be the difference or why other phones can navigate and Tytn can't.
Click to expand...
Click to collapse
I do my living buying and selling phones and I guess next time (tomorrow) I get a Wizard for sale I´ll spend enough time going thru the registry and routes to compare it with the Hermes. Would you guys mind to run IPer and check if the afore mentioned router or server with the problem is common for all of us?
I already wrote a not very nice letter to Movistar, probably they are shocked because normally their tournaround time for an answer is less than 24hrs and this time is taking longer. Next letter I´m going to be addressing the Director or whoever is the top dog.
How do I get/ run the aplication mentioned???
I would like to help to figure out what the problem is or help you guys to get to a solution...so, where can I find and how do I use the software luiggi is mentioning??
Is it free or with a trial version???
regards

Trinity - multiple little problems

Hi,
First of all, I'm new here and I'm sorry if
a) These questions have been answered here 3748 times or
b) I have put this in the wrong forum/in the wrong format. I decided to group my questions together, in order to avoid cluttering the forum.
If a moderator feels I have posted this inappropriately, I'm happy to correct it, (eg. split this post into three).
So, that much for the disclaimer, don't shoot the noob
First question:
So, I bought a (used) trinity, pretty cheaply, and for the most part have been happy with it. Even got the GPS working, with the official update from the HTC website.
So, now that I knew how the rom flashing process went, I tried flashing the Indigo rom I downloaded from the forum. The problem is, I get stuck in the rom upgrade process, when the flashing is actually supposed to start. The PDA asks me to accept running the EnterBootLoader program, I accept, and the phone restarts, then, the system pops up with "connection lost, error 246 if I remember correctly". The phone returns to normal after a soft reset, so no harm done, but no good either. Is there some solution to this problem I am unaware of. Oh, the same happens when I try to flash hardspl too, so either, the current official ROM has some deviousness about it, or it's my computer. that is to blame.
Second question:
Two times now, my trinity's phone has played some tricks on me. First time, it showed an exclamation mark on the phone networking icon, the second time, all seemed normal, except, I couldn't access the phone settings, and when someone called me, to them it seemed I was just not picking up, but on my phone, nothing seemed to be going on. Is this normal, just another windows being windows, or could this be an indication of a hardware problem, or a problem with the dialer?
Third question:
When I first received the phone, it always tried to use GPRS or 3G to connect when I opened IE, even when there was a perfectly good WLAN connection connected. Upon ROM upgrade, all connection settings were lost. Originally, in the connection view, there were 2 or 3 sets of connection settings, now, there is only one.
- Am I supposed to add sets of settings there?
- I don't know where I am to add the 3g and GPRS settings?
- How do I set WLAN proxies, on the one set of settings I can see on connections, I can set a proxy, but it doesn't seem to work: at school, I can only see the internal network, but can't access the Internet.
I would also need to have two sets of proxy settings, one for school, one for home, is this possible?
Then, some spex from the phone, so you don't have to ask:
OS: WM5
ROM version: 1.23.403.2 (Offical, GPS enabled)
Radio version: 1.38.00.11
Protocol version: 32.71.7020.12H
ExtRom version: 1.23.405.103
Phone sold under name: HTC P3600
Finnish retail version.
Oh and on final note, this is an amazing forum, even if I started reading this a week before I got my phone, and have continued to do so ever since, the amount of information on any given subject related to PDAs and mobiles seems endless. I look forward in your insights in this matter.
Easy HTC Operator Configuration
Hi, if you have lost your Operator settings, there is an easy way
to set these settings :
You only need to download the operator configurator at http://www.planete-htc.com/index.php?mod=telechargements
It works well with Orange for me.
thanks to planete-htc
Hope this can help you.
Regards
botia said:
Hi,
First of all, I'm new here and I'm sorry if
a) These questions have been answered here 3748 times or
b) I have put this in the wrong forum/in the wrong format. I decided to group my questions together, in order to avoid cluttering the forum.
If a moderator feels I have posted this inappropriately, I'm happy to correct it, (eg. split this post into three).
So, that much for the disclaimer, don't shoot the noob
First question:
So, I bought a (used) trinity, pretty cheaply, and for the most part have been happy with it. Even got the GPS working, with the official update from the HTC website.
So, now that I knew how the rom flashing process went, I tried flashing the Indigo rom I downloaded from the forum. The problem is, I get stuck in the rom upgrade process, when the flashing is actually supposed to start. The PDA asks me to accept running the EnterBootLoader program, I accept, and the phone restarts, then, the system pops up with "connection lost, error 246 if I remember correctly". The phone returns to normal after a soft reset, so no harm done, but no good either. Is there some solution to this problem I am unaware of. Oh, the same happens when I try to flash hardspl too, so either, the current official ROM has some deviousness about it, or it's my computer. that is to blame.
Second question:
Two times now, my trinity's phone has played some tricks on me. First time, it showed an exclamation mark on the phone networking icon, the second time, all seemed normal, except, I couldn't access the phone settings, and when someone called me, to them it seemed I was just not picking up, but on my phone, nothing seemed to be going on. Is this normal, just another windows being windows, or could this be an indication of a hardware problem, or a problem with the dialer?
Third question:
When I first received the phone, it always tried to use GPRS or 3G to connect when I opened IE, even when there was a perfectly good WLAN connection connected. Upon ROM upgrade, all connection settings were lost. Originally, in the connection view, there were 2 or 3 sets of connection settings, now, there is only one.
- Am I supposed to add sets of settings there?
- I don't know where I am to add the 3g and GPRS settings?
- How do I set WLAN proxies, on the one set of settings I can see on connections, I can set a proxy, but it doesn't seem to work: at school, I can only see the internal network, but can't access the Internet.
I would also need to have two sets of proxy settings, one for school, one for home, is this possible?
Then, some spex from the phone, so you don't have to ask:
OS: WM5
ROM version: 1.23.403.2 (Offical, GPS enabled)
Radio version: 1.38.00.11
Protocol version: 32.71.7020.12H
ExtRom version: 1.23.405.103
Phone sold under name: HTC P3600
Finnish retail version.
Oh and on final note, this is an amazing forum, even if I started reading this a week before I got my phone, and have continued to do so ever since, the amount of information on any given subject related to PDAs and mobiles seems endless. I look forward in your insights in this matter.
Click to expand...
Click to collapse
OK third question seems answered. You should find network operator settings on the HTC website.
Second Question - try flashing a ROM / Radio ROM again and see if you still have the problem. (For that you'll need an answer to question One
First Question: if this happens, you should leave the phone in bootloader mode (three coloured bars on the screen) make sure it say USB at the bottom of the Trinity screen - make sure you're not using Vista as an OS - use XP. provided the above conditions are met, exit and run the Rom Upgrade Utility again. This time the progress bar should show - start moving - and your ROM will flash. Search Google for trinity guids on how to for vista if that's you case.
Thanks for the answers, first of all,
I actually found out one bit of the problem by searching the forum, it seems my firewall might have been the cause of the ActiveSync problems I've been having. The Kerio Personal firewall seemed to cause the rapimgr.exe to go into a loop, this might have caused problems to the Rom utility as well.
The strange thing is, this problem only stopped when I _uninstalled_ the KPF, not when I turned it off.
I will load the operator settings you mentioned
The only thing left is the WLAN proxy settings, how do I set them, and is there a way to have two sets of them, say, one for each network SSID?

Categories

Resources