I accidentally wiped everything on my device when following a not-so-informative youtube video, it was my own fault for not questioning their steps at all, and I was going to install an update to Pixel Experience as it wasn't letting me do it normally. I have TWRP installed and I can boot into either that or fastboot manually but it won't let me transfer files from my PC onto my Xiaomi Mi 9T via Sideload, Mount, Drag and Drop, MTP is enabled and no other means I can think of work. Everything on my phone is able to be replaced as it was all in the cloud but I need my phone at the moment and from the research I've done I believe this should be a straightforward fix however, since I can't get the software onto my phone I can't boot to it. It also won't let me transfer the firmware required and so I get ERROR: 7 and "This package requires baseband from atleast V12.0.2.0.QFJMIXM. Please upgrade firmware and retry!" My PC recognises the phone is connected and can view the files on it but every time I try to drag anything into it it looks like it's going to work and then it just stops.
If you have any other information you require to assist me I will try to be as helpful as possible however, I am quite new to this so using laymens terms would be preferable.
Did you read the instructions on the pixel experience topic? First you need to flash the firmware package for your device from here: https://xiaomifirmwareupdater.com/firmware/davinci/
Then flash the rom and format data. This should work.
I installed pixel experience this week and so far it is going well, I had to update from miui 11.0.1.0 android 9 to miui 12.0.3.0 so that ALL the system will be updated to android 10, and then I proceeded to install the pixel experience via twrp. Try to install Miui 11.0.1.0 and configure it, then from the system settings you look for the latest update, make sure the system has been updated to Android 10 before installing pixel experience. Try to use xiaomi flash tool to make a clear install
RedNas74 said:
Did you read the instructions on the pixel experience topic? First you need to flash the firmware package for your device from here: https://xiaomifirmwareupdater.com/firmware/davinci/
Then flash the rom and format data. This should work.
Click to expand...
Click to collapse
I have that downloaded and I tried putting it onto my phones internal storage and sideloading it but I couldn't get it to work.
ChristianKerr21 said:
I have that downloaded and I tried putting it onto my phones internal storage and sideloading it but I couldn't get it to work.
Click to expand...
Click to collapse
After "Format Data", you need to reboot your phone in TWRP to fix that.
Micdu70 said:
After "Format Data", you need to reboot your phone in TWRP to fix that.
Click to expand...
Click to collapse
THANK YOU SO MUCH!! You are a god-sent legend!
Related
Hello community!
First of all, I feel I have to apologize to you all since I know I have clogged the forum with a lot of requests of help about upgrading my smartphone... They are scattered all over the place so I have decided to gathered in a definitive one.
I have edited this post to make it a comprehensive guide for all the people who want to upgrade their HUAWEI P8 LITE ALICE from the stock Android 5.0.1 to the Resurrection Remix N v5.8.5. Before go any further I want you to read the following disclaimer:
PLEASE PLEASE PLEASE READ THIS!!
I am not a developer. I am not a programmer. I have been greatly helped by the user Botar230 so, unfortunately, I cannot help you in case of problems. I myself had problems and had to ask for help. The only thing I can say is to be always polite and try to explain, as best as you can, what's going on.
I will try to be as much clear as possible here but keep in mind that english is not my native language so it is possible that I might mistaking something. My apologize. I am not responsible for any damage you may do to your mobile and I am not responsible to any data loss it may occur. You should ALWAYS do a backup before proceeding. ALWAYS.
I've decided to flash Resurrection Remix N v5.8.5. because it is pre-rooted with Magisk.
BEFORE start to upgrade your mobile, read all this post twice and be sure to understood all the things I have written here. Check the links, check if you have the correct files, check if your mobile is fully charged, check if the bootloader is unlocked, check if you have the right ADB files and drivers downloaded and installed. Please do it BEFORE you start everything.
Done? Everything is fine? So, here we go!
GOAL: Moving from stock Android 5.0.1 to Resurrection Remix N v5.8.5.
MY MOBILE: Huawei P8 Lite ALICE (ALE-L21) unbranded single SIM - Build number: BalongC50B311 - Kernel 3.10.61-gcd3fde7 - EMUI 3.1
BOOTLOADER STATUS: unlocked, checked via ADB
The build number and the kernel number might differ. You should check them carefully and search around this forum how to proceed properly. Also, I totally don't know what to do if you have a double SIM phone. Sorry.
These are the files I have downloaded and put on the MicroSD before starting the whole process:
b895_update.zip
open_gapps-arm64-7.1-nano-20180702
RR-N-v5.8.5-20180302-alice-OpenKirin.zip
The file TWRP_3.1.1-0_ALICE_BL.img have to be put in the same directory where adb.exe is since you will flash it via adb command: fastboot flash recovery TWRP_3.1.1-0_ALICE_BL.img once you have entered in fastboot mode AND you have checked that your bootloader is unlocked.
Now, the next steps that worked for me are:
install TWRP_3.1.1-0 via ADB
Factory reset (Wipe -> Swipe to wipe)
update the device with b895_update to get Android 6.0 and EMUI 4 (by putting b895_update on the SD card and flash it via TWRP previously installed or via sideload as suggested by Botar230. I find myself comfortable to use ADB.)
install again TWRP_3.1.1-0_ALICE_BL via ADB or via sideload
Flash RR-N-v5.8.5-20180302-alice-OpenKirin) via TWRP AND at the same time...
Flash Open Gapps via TWRP. You HAVE TO USE THE ARM64 - 7.1 VERSION!!!
Reboot your device. It is done! :good:
NOTE!! Updating the phone to b895 will take really a lot of time. Seriously. It might be scary but it's ok. It will update EMUI too.
NOTE!! When you install TWRP via ADB, the TWRP_3.1.1-0_ALICE_BL.img file MUST BE in the same directory where the adb.exe file is.
At this point, everything should be fine, working and squeaky clean!
The ROM is pre-rooted with Magisk and that's pretty cool!
At this point I think my brief tutorial is over. If you find out something important missing or wrong, please point it out! It will help other people! Thank you!
Some links about ADB that I found quite useful:
How to Install TWRP Recovery via Fastboot On Any Android Device
How to Use ADB & Fastboot Commands with your Android Device
ADB Shell
Once again I have to thank the immense patience of BOTAR230 and all the people that worked so hard to make everything possible: I mean the guys (and gals? Maybe, I don't know... ) behind the Resurrection Remix ROM, behind the TWRP project and the Open Gapps and the many more I probably forgot! Thanks everyone!
DaGreatAssyr said:
Hello community!
First of all, I feel I have to apologize to you all since I know I have clogged the forum with a lot of requests of help about upgrading my smartphone... They are scattered all over the place so I have decided to gathered in a definitive one.
Next, I am quite insecure on all the steps so I will try to make a comprehensive list and keep it updated hoping it will help all the Huawei P8 Lite ALICE users that will do the same process I am about to do. Let's proceed!
GOAL: Moving from stock Android 5.0.1 to OpenKirin's MoKee
MY MOBILE: Huawei P8 Lite ALICE (ALE-L21) unbranded single SIM - Build number: BalongC50B311 - Kernel 3.10.61-gcd3fde7 - EMUI 3.1
BOOTLOADER STATUS: unlocked, checked via ADB
Now, the next steps would be to root the mobile. My wild guess are
install TWRP_3.1.1-0_ALICE_BL via ADB
install Magisk to root Android 5.0.1
At this point I am not perfectly sure if those steps are right AND if Magisk is the right choice to root Android 5.0.1 on my mobile. Are there other ways to do that?
Once the device is rooted, the next steps should be:
update the device with b895_update to get Android 6.0 and EMUI 4 (by putting b895_update on the SD card and flash it via TWRP previously installed)
install again TWRP_3.1.1-0_ALICE_BL via ADB
install again Magisk to root Android 6.0
install pa_alice-7.3.1-EOL-20180203 (or RR-N-v5.8.5-20180302-alice-OpenKirin)
That's the theory. I've used SR5-SuperSU-v2.82-SYSTEMMODE but it bricked the phone after I updated to Android 6.0 and the user Botar230 told me that it is no longer updated and used and suggested me to use Magisk instead.
The files I have are:
b895_update.zip
open_gapps-arm-7.1-stock-20180626.zip
RR-N-v5.8.5-20180302-alice-OpenKirin.zip
pa_alice-7.3.1-EOL-20180203.zip
TWRP_3.1.1-0_ALICE_BL.img
Previously, I have updated my device to Android 6.0 and installed TWRP 3.1.1-0 and everything went really good. When I tried to root the phone with SuperSU-v2.82, it bricked. Now the phone is restored to its initial conditions, brandless.
I have read THIS POST but it's pretty old and most of the link there are not working anymore.
So, if someone is kindly willingly to give me a hand (yeah, another one, I know... ) on this subject, I'd really appreciate it. Again.
Thanks in advance!
Click to expand...
Click to collapse
I didn't fully understand you, so I'll write a quick guide how to move from stock android 5.0.1 to any other custom ROM (I've read that you already unlocked your bootloader and flashed twrp so I'll skip those two)
First of all, use this version of TWRP.
1. Boot into TWRP
2. Factory reset (Wipe -> Swipe to wipe)
3. Flash B896 update (B895 is fine too)
4. Flash TWRP (Install -> Select image -> Recovery)
5. Flash a custom ROM of your choice
6. Flash Open GAPPS (I recommend flashing NANO version)
7. (Optionally) Flash Magisk if your custom ROM isn't pre-rooted (if unsure, check the root status before flashing)
Fun fact: You don't need to put every file on SD card to flash it. You can also use sideload
Botar230 said:
I didn't fully understand you, so I'll write a quick guide how to move from stock android 5.0.1 to any other custom ROM (I've read that you already unlocked your bootloader and flashed twrp
Click to expand...
Click to collapse
Hello Botar230! At the present time, I only unlocked the bootloader.
No TWRP installed so far.
Thank you for adding some steps I have missed (like the factory reset and the GApps! :good: )!!
The TWRP version I have is the same you suggested me so this is fine!
Yes, now that I think about, nearly all the custom ROM are pre-rooted and there's an option to switch the root in the setting panel but I will check it eventually.
I have make corrections in my list after your suggestion:
install TWRP_3.1.1-0_ALICE_BL via ADB
Factory reset (Wipe -> Swipe to wipe)
update the device with b895_update to get Android 6.0 and EMUI 4 (by putting b895_update on the SD card and flash it via TWRP previously installed or via sideload)
install again TWRP_3.1.1-0_ALICE_BL via ADB or via sideload
install pa_alice-7.3.1-EOL-20180203 (or RR-N-v5.8.5-20180302-alice-OpenKirin)
Flash open_gapps-arm-7.1-nano-20180630
Check whether the ROM is rootable and eventually flash Magisk
The files I have are:
b895_update.zip
open_gapps-arm-7.1-stock-20180626.zip (I will not use these)
open_gapps-arm-7.1-nano-20180630.zip (I will use these one! )
RR-N-v5.8.5-20180302-alice-OpenKirin.zip
pa_alice-7.3.1-EOL-20180203.zip
TWRP_3.1.1-0_ALICE_BL.img
Everything looks good now. Btw you don't need to flash nano gapps exclusively, it's just a matter of your personal preference which one you choose.
Sent from my LG-K220 using XDA Labs
Botar230 said:
Btw you don't need to flash nano gapps exclusively, it's just a matter of your personal preference which one you choose.
Click to expand...
Click to collapse
To be honest, I don't know what to choose between all the options I have seen on the website. Let's say that if the installation works properly it's a matter of seconds to make a backup and try another Gapp. For the moment I will follow your suggestion.
That's what I have done so far:
install TWRP_3.1.1-0_ALICE_BL via ADB DONE AND OK!
Factory reset (Wipe -> Swipe to wipe) DONE AND OK!
update the device with b895_update to get Android 6.0 and EMUI 4 (by putting b895_update on the SD card and flash it via TWRP previously installed or via sideload) DONE AND OK!
install again TWRP_3.1.1-0_ALICE_BL via ADB or via sideload DONE AND OK!
Everything is working fine so far but I am a little bit nervous about these one. I will take a deep breathe and I will proceed right now. I can flash the ROM and the Gapps with TWRP, right? I am mostly sure about but a confirm could ease my fear of bricking the phone again... :silly:
install pa_alice-7.3.1-EOL-20180203 (or RR-N-v5.8.5-20180302-alice-OpenKirin)
Flash open_gapps-arm-7.1-nano-20180630
Check whether the ROM is rootable and eventually flash Magisk
DaGreatAssyr said:
To be honest, I don't know what to choose between all the options I have seen on the website. Let's say that if the installation works properly it's a matter of seconds to make a backup and try another Gapp. For the moment I will follow your suggestion.
That's what I have done so far:
install TWRP_3.1.1-0_ALICE_BL via ADB DONE AND OK!
Factory reset (Wipe -> Swipe to wipe) DONE AND OK!
update the device with b895_update to get Android 6.0 and EMUI 4 (by putting b895_update on the SD card and flash it via TWRP previously installed or via sideload) DONE AND OK!
install again TWRP_3.1.1-0_ALICE_BL via ADB or via sideloadDONE AND OK!
Everything is working fine so far but I am a little bit nervous about these one. I will take a deep breathe and I will proceed right now. I can flash the ROM and the Gapps with TWRP, right? I am mostly sure about but a confirm could ease my fear of bricking the phone again... :silly:
install pa_alice-7.3.1-EOL-20180203 (or RR-N-v5.8.5-20180302-alice-OpenKirin)
Flash open_gapps-arm-7.1-nano-20180630
Check whether the ROM is rootable and eventually flash Magisk
Click to expand...
Click to collapse
Yes, everything is correct.
Sent from my LG-K220 using XDA Labs
Botar230 said:
Yes, everything is correct.
Click to expand...
Click to collapse
First of all, thank you for your immense patience!!
That's what happened so far:
install TWRP_3.1.1-0_ALICE_BL via ADB DONE AND OK!
Factory reset (Wipe -> Swipe to wipe) DONE AND OK!
update the device with b895_update to get Android 6.0 and EMUI 4 (by putting b895_update on the SD card and flash it via TWRP previously installed or via sideload) DONE AND OK!
install again TWRP_3.1.1-0_ALICE_BL via ADB or via sideload DONE AND OK!
install pa_alice-7.3.1-EOL-20180203 (or RR-N-v5.8.5-20180302-alice-OpenKirin) DONE AND OK!
I had to install the open_gapps-arm64 since the system required the ARM64 but apart that...
Flash open_gapps-arm64-7.1-stock-20180630.zip DONE BUT NOT OK! - I've tried to install the NANO and the STOCK Gapps but every time I got the same error message on TWRP: "failed to mount data: operation not supported on transport endpoint". Google Play and all the Google apps cannot connect: the Google error message is always the same: "couldn't sign in". I've double checked the login and they work both on my PC and on the other phones so I'm sure they are correct. Now I'm searching what kind of error it is but I'm not finding much infos about. Plus, there is the warning message saying that "Google Play services has stopped" and it keeps popping on the screen.
Check whether the ROM is rootable and eventually flash Magisk NOT DONE YET but it seems that it is not pre-rooted.
I am searching the web to understand what's going on here.
It's probably because the custom ROM that you've chosen uses f2fs file system on /data partition instead of ext4. Try to do this:
Boot to TWRP -> Wipe -> Advanced wipe -> Choose Data -> Repair or change file system. From here you can see if the file system of /data is ext4 or f2fs. If it's f2fs, then click Change file system and choose ext4.
Before doing all of this, you should flash b895 again, do a factory reset, flash twrp, flash your custom ROM, change /data file system, and finally gapps so there will be no conflicts between old and new gapps.
Hello again!
Sorry for the silence, got some busy day but here I am.
Before doing what you told me, I've tried to do a backup with TWRP and I've been flooded with error messages:
failed to mount '/data' (Operation not supported on transport endpoint)
Unable to recreate /data/media folder
Unable to mount storage
failed to mount '/data' (Operation not supported on transport endpoint)
Unable to mount /data/media/TWRP/.twrps
And, of course, the backup process failed.
At this point I cannot do anything with TWRP.
I cannot backup, cannot flash a ROM or a ZIP.
The phone works fine, it boots and I got no problems. I can boot it via ADB too.
I'm really scared it will brick or loop sooner or later. I am keeping it turned off and wait for any other advice before proceeding since it would be quite pesky to restart from scratch again....
Following your directions I've seen that the data file system is ext3.
DaGreatAssyr said:
Hello again!
Sorry for the silence, got some busy day but here I am.
Before doing what you told me, I've tried to do a backup with TWRP and I've been flooded with error messages:
failed to mount '/data' (Operation not supported on transport endpoint)
Unable to recreate /data/media folder
Unable to mount storage
failed to mount '/data' (Operation not supported on transport endpoint)
Unable to mount /data/media/TWRP/.twrps
And, of course, the backup process failed.
At this point I cannot do anything with TWRP.
I cannot backup, cannot flash a ROM or a ZIP.
The phone works fine, it boots and I got no problems. I can boot it via ADB too.
I'm really scared it will brick or loop sooner or later. I am keeping it turned off and wait for any other advice before proceeding since it would be quite pesky to restart from scratch again....
Following your directions I've seen that the data file system is ext3.
Click to expand...
Click to collapse
Don't worry, it won't brick. Maybe the internal storage is encrypted. In order to remove encryption, go to Wipe -> Format data.
Hello Botar230! Something funny (in a very positive way) happened! I did as you told me: I booted in recovery mode and went to WIPE -> FORMAT DATA.
Then I considered to install the other ROM I had, RR-N-v5.8.5-20180302-alice-OpenKirin and it has been the best idea I could have!!! :laugh:
After I formatted the data, I rebooted in recovery mode and checked that the problems where all disappeared and they actually did. Then I flashed the OpenKirin ROM and the Nano Gapps you told me.
SURPRISE SURPRISE the OpenKirin ROM is pre-rooted with Magisk 15.3 and the installation, this time, went perfectly fine without any trouble! Plus, Magisk updated to the latest version, the 16!
As I promised, I will now update my first post on how to upgrade my mobile phone hoping it will be useful for someone else but first I want to enjoy my brand new phone!
And, of course, I want to thank you for all the support you gave me in these days! You have been really patient and kind! I am really sorry I cannot help you back since (as you have noticed...) I am not much of an expert so all I can give you is my gratitude and thankfulness! THANK YOU 1000 TIMES BOTAR!! :highfive:
You're welcome. Have a nice day! :highfive:
Sent from my LG-K220 using XDA Labs
I folowed this tutorial https://forum.xda-developers.com/nova-plus/development/rom-aospextended-v4-6-t3717372 and all flashing was fine. Due to some inconveniences of this new flashed rom i decided to restore to default rom. I extracted recovery and update.app version Can-L11 B396 i think from firmware finder and flased with adb this recovery. After that, it asked me to do an factory reset, i did it, but it wont boot any of huawei or Aosp Extended. The main problem i have is i can`t acces any more my phone with adb terminal, maybe after flashing the new original recovery usb debbuging reverted to un-enabled. How can I do now? Thanks in advance.
campeadore said:
I folowed this tutorial https://forum.xda-developers.com/nova-plus/development/rom-aospextended-v4-6-t3717372 and all flashing was fine. Due to some inconveniences of this new flashed rom i decided to restore to default rom. I extracted recovery and update.app version Can-L11 B396 i think from firmware finder and flased with adb this recovery. After that, it asked me to do an factory reset, i did it, but it wont boot any of huawei or Aosp Extended. The main problem i have is i can`t acces any more my phone with adb terminal, maybe after flashing the new original recovery usb debbuging reverted to un-enabled. How can I do now? Thanks in advance.
Click to expand...
Click to collapse
Check this post.
I cant access my phone via adb or twrp recovery. I wonder why. Before flashing a stock recovery all Was fine, adb Was connecting with no problem.
campeadore said:
I cant access my phone via adb or twrp recovery. I wonder why. Before flashing a stock recovery all Was fine, adb Was connecting with no problem.
Click to expand...
Click to collapse
Try to flash the TWRP again with fastboot.
PS: I don't understand how you people end up like this. It never happened to me.
I cant, adb cant be connected to device. Says null operation.
finally i succeed to revert o stock rom. Now i have on About phone CAN-L11C432B397, Emui 5.0 and Android 7.0. One question please, I dont see anymore the Update system tab or something, "Actualizator" on romanian language. Is that normal? How i can check for updates?
campeadore said:
finally i succeed to revert o stock rom. Now i have on About phone CAN-L11C432B397, Emui 5.0 and Android 7.0. One question please, I dont see anymore the Update system tab or something, "Actualizator" on romanian language. Is that normal? How i can check for updates?
Click to expand...
Click to collapse
You need to install the other zip too which has the word "data_full" at zip's name or something like that.
EDIT: @campeadore, i suggest you to edit the thread name and add "[SOLVED]" at begin and write the way you've fixed your phone (the solution), so it'll help other people who might run into the same problem as you.
I`ll do it as soon i fully resolve the problem. I followed your link and everything went fine at step 1 (Go back to EMUI 4.1 (MM). System is booting, but system update is not working. So, i want to flash EMUI 5, but can-l11c432b330 or can-l11c432b396 cant be updated, around 45% gives an error. The only version who work is can-l11c432b320 but i dont have update_full_CAN-L11_hw_eu, only the first update.zip.
campeadore said:
I`ll do it as soon i fully resolve the problem. I followed your link and everything went fine at step 1 (Go back to EMUI 4.1 (MM). System is booting, but system update is not working. So, i want to flash EMUI 5, but can-l11c432b330 or can-l11c432b396 cant be updated, around 45% gives an error. The only version who work is can-l11c432b320 but i dont have update_full_CAN-L11_hw_eu, only the first update.zip.
Click to expand...
Click to collapse
Newer / newest firmware downloaded from Firmware Finder needs to be approved by Huawei and that can take some time. It's failing to install because it wasn't approved. I've read this in past somewhere.
Try B381 or B382 as i've always installed that one when i've went back to EMUI 5.
Yes, i did it now with can-l11c432b330. I think my mistake was trying to flash to EMUI5 with usb cable connected. With cable off all went fine like a charm. Now i do all approved updates with system update. Thank you so much man, really appreciated.
Seeking help: I have a smartphone huawei nova lite plus (TRT LX1) that fails to restart. It goes continuously in a loop. Entering recovery only the first 2 functions come out: wipe wash factory reset and wipe wash partition. Then using eRecovery from PC with the USB cable, proceed up to a certain point and then not continue. I think it's in soft brick. I definitely need the right software for flashing, stock roms and usb drivers. Where can I find them? Many thanks
just use MsmDownloadTool V4.0.exe to recovery my op5 to oos, but the version is quite low as Android 7.1.1.
checked the system update, it told me up to date. which is of course not true.
tried to clean the cache of google framework service and oneplus framework service, still nothing in updating.
tried installed oxygen updater, and download 3 update zip from 7.1.4, 8, last version of 8, but each time I use local install in system uploading, then reboot to recovery, it shows me "failed". none of version works.
I even tried to install in recovery, wipe cache and data or just wipe data, then install from internal disk, none of the file works, even don't have any popup fail notice, just go back to file chooser interface.
I can still go back to system by switch off and on again.
How can I upgrade the old version of android in my oneplus 5?
original:
used use lineages os with Twrp, and I would like to flash to original oxygen.
download full rom zip in https://www.oneplus.com/uk/support/softwareupgrade/details?code=PM1574156143164
copied to phone disk
went to twrp
wipe Dalvik, System, Data, and Cache
then tried to install the full rom zip, but met "no Digest File found" error
found it must be twrp old, so I download new one in https://dl.twrp.me/cheeseburger_dumpling/twrp-3.4.0-0-cheeseburger_dumpling.img.html
copy to phone and flash it to recovery.
select "reboot to recovery"
then problem coming: I can only see the oneplus logo with powered by Android. it won't go any further.
I am not sure any thing wrong during my processing, but maybe 2 things:
1, I wiped the system
2, I didn't clean the screen lock pin before I flash
so, my question here is, if possible I can flash the original oxygen os in this situation?
if positive, could you please give me a step by step instruction?
by the way, the zip rom I download from oneplus site isn't have the "flash-all" script.
please please help me .
First install OxygenOS 5.1.4 based on Android Oreo and boot to that version to create /vendor partition for Treble support
Pierre02 said:
First install OxygenOS 5.1.4 based on Android Oreo and boot to that version to create /vendor partition for Treble support
Click to expand...
Click to collapse
thanks! it works! i'm at 5.1.2 then i install OxygenOS 5.14 (OnePlus5Oxygen_23_OTA_037_all_1807181258_7b4b6.zip) then after that I install OnePlus5Oxygen_23_OTA_042_all_1812232102_a034988b.zip and then the last and the latest OnePlus5Oxygen_23_OTA_068_all_2006012224_c7a6016.zip android 10.
Please help. I bought a phone with Beta installed. I wanted to switch to the original system. So I screwed up something so using the MsmDownloadTool tool I wanted to use it by uploading everything from scratch. I fell into the Chinese H2Os system. I searched again and I already have the original ColorOS based on Android 9. But I can't update it to 10. What do I have to do? Oh .... the bootloader is unlocked ...
uno0 said:
Please help. I bought a phone with Beta installed. I wanted to switch to the original system. So I screwed up something so using the MsmDownloadTool tool I wanted to use it by uploading everything from scratch. I fell into the Chinese H2Os system. I searched again and I already have the original ColorOS based on Android 9. But I can't update it to 10. What do I have to do? Oh .... the bootloader is unlocked ...
Click to expand...
Click to collapse
Use an EDL Flasher (unbrick tool) here on XDA
Pierre02 said:
First install OxygenOS 5.1.4 based on Android Oreo and boot to that version to create /vendor partition for Treble support
Click to expand...
Click to collapse
thanks for replying
I had figure out my problem.
it seems the rom I flashed using MsmDownloadTool had something wrong,
I've changed another one, it shows me the update from the first start after flashing.
uno0 said:
Please help. I bought a phone with Beta installed. I wanted to switch to the original system. So I screwed up something so using the MsmDownloadTool tool I wanted to use it by uploading everything from scratch. I fell into the Chinese H2Os system. I searched again and I already have the original ColorOS based on Android 9. But I can't update it to 10. What do I have to do? Oh .... the bootloader is unlocked ...
Click to expand...
Click to collapse
if you are directly flash to coloros android 9 from lower version other than android 8, it might be the problem you won't got the update in the system. It might be have issue in wifi or gps as well, which I bet you didn't well test yet.
that's all about the system partitions messed up. regarding my understanding.
solution is simple, but time consuming:
you have to flash an original rom using msmdownloadtool, make sure that rom will have update notification in the system menu of settings. then upgrade from there one level up each time, till to the android 10. (chinese version do have 10 available)
than, you can download oxygen os android 10 to flash on the coloros android 10 (hydrogen os android 10) you just done the upgrade, don't forget wipe data/cache before flashing.
hope that's helps.
netzkie said:
thanks! it works! i'm at 5.1.2 then i install OxygenOS 5.14 (OnePlus5Oxygen_23_OTA_037_all_1807181258_7b4b6.zip) then after that I install OnePlus5Oxygen_23_OTA_042_all_1812232102_a034988b.zip and then the last and the latest OnePlus5Oxygen_23_OTA_068_all_2006012224_c7a6016.zip android 10.
Click to expand...
Click to collapse
Kindly tell me in steps you follow m stuck in 4.5.8 version with download links
After flashing back oxygen os to both slots I can't download all my apps. Putting the phone to download google backup(like apps and such) it fails to install over 40 apps out of 170 and when trying to update apps, playstore says that the app which I'm trying to update needs SD card or other media device with sufficent space while i have over 90gb free. I have also tried to use the unbricking tool with no luck. WhatsApp doesn't want to restore either. I've also tried to download ota file with chrome and chrome says also that I don't have enough space.
Try fastboot
You should try flash again with fastboot-ROM
Thevili03 said:
After flashing back oxygen os to both slots I can't download all my apps. Putting the phone to download google backup(like apps and such) it fails to install over 40 apps out of 170 and when trying to update apps, playstore says that the app which I'm trying to update needs SD card or other media device with sufficent space while i have over 90gb free. I have also tried to use the unbricking tool with no luck. WhatsApp doesn't want to restore either. I've also tried to download ota file with chrome and chrome says also that I don't have enough space.
Click to expand...
Click to collapse
Use msm tool instead...i got this issue when came back from custom rom! Some partition is messing up
Thevili03 said:
After flashing back oxygen os to both slots I can't download all my apps. Putting the phone to download google backup(like apps and such) it fails to install over 40 apps out of 170 and when trying to update apps, playstore says that the app which I'm trying to update needs SD card or other media device with sufficent space while i have over 90gb free. I have also tried to use the unbricking tool with no luck. WhatsApp doesn't want to restore either. I've also tried to download ota file with chrome and chrome says also that I don't have enough space.
Click to expand...
Click to collapse
I had the same problem after make a oos reinstall with a .bat I download, I solved the problem copying all the internal memory to my pc and making a full wipe (internal memory included) and a reinstall via fastboot with the .bat
maybe copy and wipe the internal memory and reinstall the rom can solve the problem, if not I can upload the fastboot unbrick .bat I use to gdrive and you can try a reinstall it is oos pie 9.0.17 but you can always update to oos 10
So, I got it to working with msm-tool. It went back to oos 9.0.16 and then I upgraded to oos 10.3.5, resetted again, and got everything working. But now I think that I got the Indian version or something, because I have red cable club and oneplus cloud there, I live in Finland so obviously they aren't working here. Can I somehow get the international version of oos?
For anybody reading this in the future, this is actually caused by invalid decryption keys. It's possible to have Android boot but not successfully decrypt data. In this state the phone will boot but no applications will install and saving files won't work correctly.
Simply wiping data should fix the issue, but there's always the MSM tool for when things go really wrong.
use fastboot roms to refresh your device and remove data encryptions
Thevili03 said:
So, I got it to working with msm-tool. It went back to oos 9.0.16 and then I upgraded to oos 10.3.5, resetted again, and got everything working. But now I think that I got the Indian version or something, because I have red cable club and oneplus cloud there, I live in Finland so obviously they aren't working here. Can I somehow get the international version of oos?
Click to expand...
Click to collapse
International/global same thing. There are twrp flashable OOS that are global for 6t here: https://forum.xda-developers.com/oneplus-6t/how-to/oneplus-6t-global-repo-oxygen-os-builds-t3865396
Next time you want to roll back to OOS from a custom rom:
Boot twrp
Flash OOS 10.3.5 global from that link
Flash twrp installer zip
Flash finalize zip
Format data (remember this wipes everything)
Reboot system.
You will not have this issue if you install that way.
Then if you want root boot twrp and flash magisk , reboot system.
Also if you ever have to use Msm tool again you can use the last Android 9/pie twrp by mauronofrio. The twrp he compiled just before Android 10/Q twrp started.. You can use that twrp and just flash OOS 10.3.5 global rom after you run Msm tool. That way updating won't take so long. That's what I did and had no issues. Just don't ever downgrade OOS via TWRP or you'll brick.
Hi there!
So, i'm currently at miui 12.0.5,and yesterday i attemped to install Pixel Experience 11, got an error during the adb sideload (as it is said on the official site, that's the way to go after the factory reset plus format data). i could not move the zip file into the phone's storage to actually install it via "traditional flash method" since i couldnt access the directory from my pc, twrp claimed that i had an old baseband and asked to install a new firmware, At the og post of this rom it is said that versions above miui 12.0.2 can just flash the rom in twrp and format data, is there any other way to flash a rom with the format data thing? did i miss any step? do i actually need to install a new firmware?.
Also might be important to say that i chose the plus version because i thought it would have some extra features, was that my actual error around this topic? i mean, should i pick the "normal" pixel experience zip¿?
Thanks in advance and have a nice day!!