Related
How to install TWRP 3.0 and ROOT on HTC Desire 626 LTE.
The step by step guideline is like these :
1. Unlock bootloader of this instruction Link
2. Download TWRP and TWRP-Install.zip. TWRP - Link , TWRP-Install.zip - Link, Root archive - Link
3. Reboot phone in Fastboot Mode.
4. Copy twrp-fastboot-boot.img into fastboot folder, archive TWRP-Install.zip - in Internal Memory.
5. Open fastboot and enter this command
Code:
fastboot boot twrp-fastboot-boot.img
Your phone reboot in temporary TWRP.
6. Accept system modification alert by swipe.
7. Go to Install and choose TWRP-Install.zip, accept this by swipe.
8. Go to Reboot and reboot in recovery.
9. ??????????
10. PROFIT!
Bugs
Mount reserve partition(is not critical).
Contributors
Skyrimus
Original link - http://4pda.ru/forum/index.php?s=&showtopic=701301&view=findpost&p=54026939
Hi, my phone is stuck at the Fastboot page
I have tried flash in
1) your receovery linked above
2)customized recovery under this link https://twrp.me/devices/htcdesire626s.html
But none of them works.
Can you please help to give some advise?
Skyrimus said:
How to install TWRP 3.0 and ROOT on HTC Desire 626 LTE.
The step by step guideline is like these :
1. Unlock bootloader of this instruction Link
2. Download TWRP and TWRP-Install.zip. TWRP - Link , TWRP-Install.zip - Link, Root archive - Link
3. Reboot phone in Fastboot Mode.
4. Copy twrp-fastboot-boot.img into fastboot folder, archive TWRP-Install.zip - in Internal Memory.
5. Open fastboot and enter this command
Code:
fastboot boot twrp-fastboot-boot.img
Your phone reboot in temporary TWRP.
6. Accept system modification alert by swipe.
7. Go to Install and choose TWRP-Install.zip, accept this by swipe.
8. Go to Reboot and reboot in recovery.
9. ??????????
10. PROFIT!
Bugs
Mount reserve partition(is not critical).
Contributors
Skyrimus
Original link - http://4pda.ru/forum/index.php?s=&showtopic=701301&view=findpost&p=54026939
Click to expand...
Click to collapse
Finally! Thanks alot for your share Skyrimus.
I don't believe you can install TWRP via fastboot if your phone is in s-on state, correct me if I'm wrong, but what I did to install TWRP was I downloaded the official version for my phone (duh) and used the same fastboot commands while phone was in fastboot mode which resulted in a message "FAILED: <remote: cannot flash this partition in s-on state>"
I resolved this by rebooting to download mode instead and running the commands as normal and all went well, so if you don't have your phone in s-off and received the same error as me then download mode will do the trick
Skyrimus said:
How to install TWRP 3.0 and ROOT on HTC Desire 626 LTE.
The step by step guideline is like these :
1. Unlock bootloader of this instruction Link
2. Download TWRP and TWRP-Install.zip. TWRP - Link , TWRP-Install.zip - Link, Root archive - Link
3. Reboot phone in Fastboot Mode.
4. Copy twrp-fastboot-boot.img into fastboot folder, archive TWRP-Install.zip - in Internal Memory.
5. Open fastboot and enter this command
Code:
fastboot boot twrp-fastboot-boot.img
Your phone reboot in temporary TWRP.
6. Accept system modification alert by swipe.
7. Go to Install and choose TWRP-Install.zip, accept this by swipe.
8. Go to Reboot and reboot in recovery.
9. ??????????
10. PROFIT!
Bugs
Mount reserve partition(is not critical).
Contributors
Skyrimus
Original link - http://4pda.ru/forum/index.php?s=&showtopic=701301&view=findpost&p=54026939
Click to expand...
Click to collapse
Hi Skyrimus !
Can you give me a more details about "reserve partition" ? A trayed your metod- that partialy working, but to the moment TWRP menu with prompt swap to allow write. Than frozen screan, i can do nothig, and starting system android phone under this screan.. My model: HTC Desire 626. (LTE internet) Android 5.1 loolipop. not 6 Can you help me to get apropriate TWRP, or any thinks ? My knowlege is not to good..
Hey, is someone able to extract the RUU from this htc desire 626 lte? i softbricked it and cannot find anything working. Thats the version with snapdragon 410, isn't it?
Zwolin said:
Hey, is someone able to extract the RUU from this htc desire 626 lte? i softbricked it and cannot find anything working. Thats the version with snapdragon 410, isn't it?
Click to expand...
Click to collapse
did uou pres power button, simultanously volume + up to 10 seconds ?
---------- Post added at 09:56 PM ---------- Previous post was at 09:00 PM ----------
janalaa said:
Hi Skyrimus !
Can you give me a more details about "reserve partition" ? A trayed your metod- that partialy working, but to the moment TWRP menu with prompt swap to allow write. Than frozen screan, i can do nothig, and starting system android phone under this screan.. My model: HTC Desire 626. (LTE internet) Android 5.1 loolipop. not 6 Can you help me to get apropriate TWRP, or any thinks ? My knowlege is not to good..
Click to expand...
Click to collapse
Skyrimus said:
How to install TWRP 3.0 and ROOT on HTC Desire 626 LTE.
The step by step guideline is like these :
1. Unlock bootloader of this instruction Link
2. Download TWRP and TWRP-Install.zip. TWRP - Link , TWRP-Install.zip - Link, Root archive - Link
3. Reboot phone in Fastboot Mode.
4. Copy twrp-fastboot-boot.img into fastboot folder, archive TWRP-Install.zip - in Internal Memory.
5. Open fastboot and enter this command
Code:
fastboot boot twrp-fastboot-boot.img
Your phone reboot in temporary TWRP.
6. Accept system modification alert by swipe.
7. Go to Install and choose TWRP-Install.zip, accept this by swipe.
8. Go to Reboot and reboot in recovery.
9. ??????????
10. PROFIT!
Bugs
Mount reserve partition(is not critical).
Contributors
Skyrimus
Original link - http://4pda.ru/forum/index.php?s=&showtopic=701301&view=findpost&p=54026939
Click to expand...
Click to collapse
Resolved for android 5.1 loolipop :
after unlock bootloader-
1. in the mobile system android, use Kingo Root.apk -one toutch ROOT (temporary)
2. flash custom "recovery. img" downloaded to SDcard , by use RASHR. apk (ply store)
3. reboot to fastboot mode, move highlite menu- to recovery mode- push pwr button - wait, wil Starts TWRP 3.0.0 Skyrimus
Profit! It was very simple
Bugs : mount reserve partition error (stil.)
Linkes for download files 1 topic (Skyrymus)
Thank you Skyrimus, greate job!
Compilation
Hi Skyrimus,
I want to compile a LineageOS rom for the HTC desire 626.
Have you still got configurations files ?
hello sir
Skyrimus said:
How to install TWRP 3.0 and ROOT on HTC Desire 626 LTE.
The step by step guideline is like these :
1. Unlock bootloader of this instruction Link
2. Download TWRP and TWRP-Install.zip. TWRP - Link , TWRP-Install.zip - Link, Root archive - Link
3. Reboot phone in Fastboot Mode.
4. Copy twrp-fastboot-boot.img into fastboot folder, archive TWRP-Install.zip - in Internal Memory.
5. Open fastboot and enter this command
Code:
fastboot boot twrp-fastboot-boot.img
Your phone reboot in temporary TWRP.
6. Accept system modification alert by swipe.
7. Go to Install and choose TWRP-Install.zip, accept this by swipe.
8. Go to Reboot and reboot in recovery.
9. ??????????
10. PROFIT!
Bugs
Mount reserve partition(is not critical).
Contributors
Skyrimus
Original link - http://4pda.ru/forum/index.php?s=&showtopic=701301&view=findpost&p=54026939
Click to expand...
Click to collapse
sir am using htc desire 626q veriant i cant upgrade to lolipop or other plzz help me with full toturial video link
Hi,
Today I just installed a custom ROM for my Zuk Z2 PRO. This tutorial is how I did it.
I get many ressources from this forum and I thank orignal authors.
Big thanks to meister for his guide : https://forum.xda-developers.com/zuk-z2-pro/how-to/zuk-z2-pro-guide-to-everything-ota-t3562099
And big thanks to m_atze for his guide : https://forum.xda-developers.com/zuk-z2-pro/how-to/howto-flash-stock-rom-t3435109
More info on this ROM : https://forum.xda-developers.com/zuk-z2-pro/development/rom-share-lr-team-zuk-z2row-z2-pro-t3567710
Backup your data before processing the flash, in order to avoid loss of data!
Flashing / rooting and install custom ROM could brick your device ! You're the only responsible on what you're doing. This guide is how I did it and I'm not responsible if you're messing up your device
Unlock bootloader (step 3) will void Lenovo warranty
Antutu Score : 143050
Summary :
Step 1 : Prepare environment
Step 2 : Install ZUI 2.5.x (recommended before installing Nougat custom ROM)
Step 3 : Unlock bootloader (to be able to boot on TWRP)
Step 4 : Boot on TWRP to root the phone
Step 5 : Make a Nandroid backup
Step 6 : Install TWRP
Step 7 : Install a custom ROM with TWRP
Step 8 : Install Gapps (google apps)
Step 1 : Prepare environment
Create a directory where you're gona extract download files (avoid space in the directory path).
Download : adb and fastboot from google
Extract it on your previous created directory.
Download usb drivers and install it
Enable developer mode in your Z2 PRO (link if your don't know how to do it)
Connect your phone on your computer
On the directory C:/yourDirectoryPath/platform-tools maintains shift + rigth click and "Open command window here"
Type adb devices
If your see a line below "List of devices attached" your adb is OK
Note the number somewhere, it's your device serial number.
On the phone type *#06# and note somewhere IMEI numbers in case something went wrong during flashing
Step 2 : Install ZUI 2.5.x (recommended before installing Nougat custom ROM)
For this part I use the m_atze tutorial that you can find here. Check it for me detailed steps.
If you are on windows 8, 8.1 or 10, you have to disable driver verification (some people didn't disable driver verification and it works as well)
For windows 10 with anniversary update : you just have to run a cmd as admin and enter bcdedit -set TESTSIGNING ON then reboot your computer (your windows will be in test mode)
For other cases check this link
Then
Download QPST flashtool
Install QPST flashtool and reboot your computer
Download and extract ZUI ROM 2.5.x (you maybe need to rename the directory where the ROM is because it could be too big)
Launch QFIL application as administrator
Go to Configuration -> FireHostConfiguration. 1-change device type to UFS. 2-check reset after download checkbox
Click on "Load content" and browse the contents.xml from the ZUI ROM 2.5.x extracted files
On the adb console you opened earlier, enter adb reboot edl
The QFIL page should look like this
Click on "Download content" to flash your phone
The final screen should like this
If any problem, there is an FAQ
Your phone is gonna reboot, congratulation, you're flashed your phone with ZUI 2.5.x ROM.
Once the phone boots up it will be in Chinese again. To get your phone back in English :
On the welcome screen tap the bottom of the screen below the highlighted blue text to skip the ZUK login.
To change the language back to English go to Settings.
In the third section choose the last entry. "Advanced Settings" (the gears symbol).
Choose the 2nd menu item.
Choose the first menu item and select English.
Now check update and install it if needed trough this app. If the check is green, it's ok.
Re-enable developer mode and debugging
Step 3 : Unlock bootloader (to be able to boot on TWRP)
This step is almost a copy past of section 2 of meister guide
This step gonna void your Lenovo warranty and wipe your data
Step 3.1 : Get the unlock bootloader from Lenovo
In order to unlock the bootloader you will need to got the zuk website, where you need to register first before you can request to unlock the bootloader.
So go here : https://passport.zuk.com/wauthen3/wauth/jsp/register.jsp (use google translate)
Select Email Registration (upper right corner) and fill in the required data
You will receive an Email with a confirmation link.
Now that you are registered, log in and than go to http://developer.zuk.com/bootloader (use google translate)
Click on Carry On.
On the next page select your phone type Z2 Pro.
Enter your serial number (8 digits) (you can find it on Settings -> About -> Status. If your serial is not 8 digit, add 0 to the end to make a 8 digit number)
Enter an email address where to send the unlock image. It seems that the email address here has to follow some rules. ([email protected] or @Web.net seems to work. A domain name with a hyphen (-) seems to cause problems, i use a @hotmail.com mail adresse and it worked)
Check the 2 check boxes and click SUBMIT
If successful you get a message that the image has been sent to your email address. No message means something went wrong. Likely the email address was not approved.
Save the email attachment from ZUK you requested earlier (named unlock_bootloader.img) into C:/yourDirectoryPath/platform-tools/ (next to adb.exe)
Step 3.2 : Unlock bootloader
On adb console enter adb devices to check if your device is still connected
Next enter adb reboot bootloader and your phone gonna reboot in bootloader mode
Next enterfastboot -i 0x2b4c flash unlock unlock_bootloader.img (if you got error "target did not report max-download-size" change from usb 3.0 to usb 2.0 port and / or try to turn on "enable_usb_2.0" via
Developer Options)
You should see
Code:
target reported max download size of 1610612736 bytes
sending 'unlock' (0 KB)...
OKAY [ 0.031s]
writing 'unlock'...
OKAY [ 0.063s]
finished. total time: 0.094s
Then enter fastboot -i 0x2b4c oem unlock-go
You should see
Code:
...
OKAY [ 0.031s]
finished. total time: 0.031s
You phone is gonna reboot (or reboot it manually)
Change the phone language to english and re enable debugging.
Step 4 : Boot on TWRP to root the phone
Download TWRP 3.1 for Zuk Z2 PRO here and extrat TWRP..... .img next to adb.exe in platform-tools folder
Download SuperSu here
Copy paste SuperSu zip file in your phone internal storage
In adb cmd enter adb reboot bootloader
Then enter fastboot -i 0x2b4c boot TWRP3.1.0.0_ZUK_Z2_pro.img to boot in TWRP image
Click on "Keep read only"
Go to install and browse to SuperSu zip.
Swipe to install
When installation is finished, reboot your phone (it may reboot many times)
Good job, your phone is now rooted !
Step 5 : Make a Nandroid backup
In adb cmd enter adb reboot bootloader
Then enter fastboot -i 0x2b4c boot TWRP3.1.0.0_ZUK_Z2_pro.img to boot in TWRP image
Go in backup and check all checkbox
Swipe to backup
Reboot the phone
From your computer browse your phone internal memory and copy your backup from TWRP/Backup/XXXXX to a directory in your computer
Step 6 : Install TWRP
In adb cmd enter adb reboot bootloader
Then fastboot flash recovery TWRP3.1.0.0_ZUK_Z2_pro.img to install TWRP on your phone
Then fastboot reboot
Then adb reboot bootloader
Then with volume keys select Recovery Mode and enter in Recovery Mode by pushing power key
TWRP will start
Reboot your phone
Step 7 : Install a custom ROM with TWRP
Download ROM from https://uploadfiles.io/55ffa
Copy paste ROM zip file in your phone internal storage
In adb cmd enter adb reboot bootloader
Then with volume keys select Recovery Mode and enter in Recovery Mode by pushing power key
Click Wipe and swipe to wipe. Do NOT reboot your phone.
Go back in TWRP main menu and click Install. Browse the ROM zip file
Swipe to install
Reboot your phone
When your phone reboot, it's in chinese. Click on the texte in the right bottom corner and then select your language.
During the phone configuration, do not connect wifi (in my case the phone configuration crashed when I connected to a wifi)
When you finished phone configuration reboot to get notification in your language
Step 8 : Install Gapps (google apps)
Download Gapps from https://forum.xda-developers.com/android/software/gapps-dynamic-gapps-t3487192
Copy the zip file in your phone
Reboot in TWRP
Install Gapps through TWRP
Reboot your phone
At this point my Google Play Services crashed each reboot. So needed to
Reboot in TWRP
Wipe cache
Now it works !
You can install other ROM with this method but I only tested with this one.
Enjoy
First of all, thank you for your help.
I followed this tutorial from start to finish without encountering any unexpected events. It is rare to say so!
Small points:
Step 1:
*- Think of connecting the phone before the command "adb devices", it's stupid but I had not done it!
Step 2:
*- I did not need to change my driver settings on Windows 10.
*- I had to run the QFIL application as an administrator.
*- I had to rename the directory where the ROM was because the name was too big.
Step 3.1:
*- I have a serial number on 7 characters, you must add "0" at the end to make 8 characters.
*- My Gmail address worked smoothly.
Step 4:
*- The SuperSU link did not work, I took this one: http://downloadmirror.co/Utz/UPDATE-SuperSU-v2.79-20161211114519.zip
*- Some reboot at home also, it seems to be normal.
Step 7:
*- I took the ROM "Resurrection Remix", no problem with another ROM.
Step 8:
*- I also had a crash of Google apps, I also did a wipe and it works now. It looks normal too.
Thank you again for your help!
Glade I could help !
Thanks for your feedback, I'm gonna update the tutorial
Hi,
great tutorial, thank you!
Step 6 : Install TWRP - I'm stuck though, as my PC still does not recognize device on fastboot without -i 0x2b4c...
so should I use instead of
Then fastboot flash recovery TWRP3.1.0.0_ZUK_Z2_pro.img to install TWRP on your phone
Then fastboot reboot
Click to expand...
Click to collapse
the -i option ?
Then fastboot -i 0x2b4c flash recovery TWRP3.1.0.0_ZUK_Z2_pro.img to install TWRP on your phone
Then fastboot -i 0x2b4c reboot
Click to expand...
Click to collapse
?
... edit, yes that worked ...
lxlx said:
... edit, yes that worked ...
Click to expand...
Click to collapse
Great ! Good to know
Step 3.1 : Get the unlock bootloader from Lenovo
- gmail works
- did not work to get the bootloader with google translater . had to do it in Chinese, but knew the steps since i tried it with translation first
zwat said:
Step 3.1 : Get the unlock bootloader from Lenovo
- gmail works
- did not work to get the bootloader with google translater . had to do it in Chinese, but knew the steps since i tried it with translation first
Click to expand...
Click to collapse
Thanks for the feedback, I updated the tuto.
Thank you for this tutorial, it worked like a charm!
I'm currently on ZUI 2.5.x. Can I go straight to official MK60.1 using this guide?
Or should I downgrade to ZUI 2.3.x first
dommels said:
I'm currently on ZUI 2.5.x. Can I go straight to official MK60.1 using this guide?
Or should I downgrade to ZUI 2.3.x first
Click to expand...
Click to collapse
I don't know sorry :/
Maybe downgrade to 2.3.x is more secured...
For my information, why do you want to install the MK60.1 ?
Bluud said:
I don't know sorry :/
Maybe downgrade to 2.3.x is more secured...
Click to expand...
Click to collapse
Just went from stock 2.5x to MK60.1 without issues, thanks!
For my information, why do you want to install the MK60.1 ?
Click to expand...
Click to collapse
So far it's the only stable official release from Mokee.
Mk60.1 have exactly the same bugs like Mk71.1. so no need to use mk60.1. mk71.1 is pretty stable btw.
So far quite happy running Mokee. Is there an easy way to root as well?
dommels said:
So far quite happy running Mokee. Is there an easy way to root as well?
Click to expand...
Click to collapse
Mokee was quite good.
Yesterday I installed this ROM : https://forum.xda-developers.com/zu...tom-rom-zuk-z2pro-resurrection-remix-t3579113
I prefer this ROM because you can custom it in many ways.
Since yesterday it's stable.
Question
Bluud said:
Mokee was quite good.
Yesterday I installed this ROM : https://forum.xda-developers.com/zu...tom-rom-zuk-z2pro-resurrection-remix-t3579113
I prefer this ROM because you can custom it in many ways.
Since yesterday it's stable.
Click to expand...
Click to collapse
It's the same tutorial?
Yes
Bluud said:
Hi,
Today I just installed a custom ROM for my Zuk Z2 PRO. This tutorial is how I did it.
I get many ressources from this forum and I thank orignal authors.
Big thanks to meister for his guide : https://forum.xda-developers.com/zuk-z2-pro/how-to/zuk-z2-pro-guide-to-everything-ota-t3562099
And big thanks to m_atze for his guide : https://forum.xda-developers.com/zuk-z2-pro/how-to/howto-flash-stock-rom-t3435109
More info on this ROM : https://forum.xda-developers.com/zuk-z2-pro/development/rom-share-lr-team-zuk-z2row-z2-pro-t3567710
Backup your data before processing the flash, in order to avoid loss of data!
Flashing / rooting and install custom ROM could brick your device ! You're the only responsible on what you're doing. This guide is how I did it and I'm not responsible if you're messing up your device
Unlock bootloader (step 3) will void Lenovo warranty
Antutu Score : 143050
Summary :
Step 1 : Prepare environment
Step 2 : Install ZUI 2.5.x (recommended before installing Nougat custom ROM)
Step 3 : Unlock bootloader (to be able to boot on TWRP)
Step 4 : Boot on TWRP to root the phone
Step 5 : Make a Nandroid backup
Step 6 : Install TWRP
Step 7 : Install a custom ROM with TWRP
Step 8 : Install Gapps (google apps)
Step 1 : Prepare environment
Create a directory where you're gona extract download files (avoid space in the directory path).
Download : adb and fastboot from google
Extract it on your previous created directory.
Download usb drivers and install it
Enable developer mode in your Z2 PRO (link if your don't know how to do it)
Connect your phone on your computer
On the directory C:/yourDirectoryPath/platform-tools maintains shift + rigth click and "Open command window here"
Type adb devices
If your see a line below "List of devices attached" your adb is OK
Note the number somewhere, it's your device serial number.
On the phone type *#06# and note somewhere IMEI numbers in case something went wrong during flashing
Step 2 : Install ZUI 2.5.x (recommended before installing Nougat custom ROM)
For this part I use the m_atze tutorial that you can find here. Check it for me detailed steps.
If you are on windows 8, 8.1 or 10, you have to disable driver verification (some people didn't disable driver verification and it works as well)
For windows 10 with anniversary update : you just have to run a cmd as admin and enter bcdedit -set TESTSIGNING ON then reboot your computer (your windows will be in test mode)
For other cases check this link
Then
Download QPST flashtool
Install QPST flashtool and reboot your computer
Download and extract ZUI ROM 2.5.x (you maybe need to rename the directory where the ROM is because it could be too big)
Launch QFIL application as administrator
Go to Configuration -> FireHostConfiguration. 1-change device type to UFS. 2-check reset after download checkbox
Click on "Load content" and browse the contents.xml from the ZUI ROM 2.5.x extracted files
On the adb console you opened earlier, enter adb reboot edl
The QFIL page should look like this
Click on "Download content" to flash your phone
The final screen should like this
If any problem, there is an FAQ
Your phone is gonna reboot, congratulation, you're flashed your phone with ZUI 2.5.x ROM.
Once the phone boots up it will be in Chinese again. To get your phone back in English :
On the welcome screen tap the bottom of the screen below the highlighted blue text to skip the ZUK login.
To change the language back to English go to Settings.
In the third section choose the last entry. "Advanced Settings" (the gears symbol).
Choose the 2nd menu item.
Choose the first menu item and select English.
Now check update and install it if needed trough this app. If the check is green, it's ok.
Re-enable developer mode and debugging
Step 3 : Unlock bootloader (to be able to boot on TWRP)
This step is almost a copy past of section 2 of meister guide
This step gonna void your Lenovo warranty and wipe your data
Step 3.1 : Get the unlock bootloader from Lenovo
In order to unlock the bootloader you will need to got the zuk website, where you need to register first before you can request to unlock the bootloader.
So go here : https://passport.zuk.com/wauthen3/wauth/jsp/register.jsp (use google translate)
Select Email Registration (upper right corner) and fill in the required data
You will receive an Email with a confirmation link.
Now that you are registered, log in and than go to http://developer.zuk.com/bootloader (use google translate)
Click on Carry On.
On the next page select your phone type Z2 Pro.
Enter your serial number (8 digits) (you can find it on Settings -> About -> Status. If your serial is not 8 digit, add 0 to the end to make a 8 digit number)
Enter an email address where to send the unlock image. It seems that the email address here has to follow some rules. ([email protected] or @Web.net seems to work. A domain name with a hyphen (-) seems to cause problems, i use a @hotmail.com mail adresse and it worked)
Check the 2 check boxes and click SUBMIT
If successful you get a message that the image has been sent to your email address. No message means something went wrong. Likely the email address was not approved.
Save the email attachment from ZUK you requested earlier (named unlock_bootloader.img) into C:/yourDirectoryPath/platform-tools/ (next to adb.exe)
Step 3.2 : Unlock bootloader
On adb console enter adb devices to check if your device is still connected
Next enter adb reboot bootloader and your phone gonna reboot in bootloader mode
Next enterfastboot -i 0x2b4c flash unlock unlock_bootloader.img (if you got error "target did not report max-download-size" change from usb 3.0 to usb 2.0 port and / or try to turn on "enable_usb_2.0" via
Developer Options)
You should see
Then enter fastboot -i 0x2b4c oem unlock-go
You should see
You phone is gonna reboot (or reboot it manually)
Change the phone language to english and re enable debugging.
Step 4 : Boot on TWRP to root the phone
Download TWRP 3.1 for Zuk Z2 PRO here and extrat TWRP..... .img next to adb.exe in platform-tools folder
Download SuperSu here
Copy paste SuperSu zip file in your phone internal storage
In adb cmd enter adb reboot bootloader
Then enter fastboot -i 0x2b4c boot TWRP3.1.0.0_ZUK_Z2_pro.img to boot in TWRP image
Click on "Keep read only"
Go to install and browse to SuperSu zip.
Swipe to install
When installation is finished, reboot your phone (it may reboot many times)
Good job, your phone is now rooted !
Step 5 : Make a Nandroid backup
In adb cmd enter adb reboot bootloader
Then enter fastboot -i 0x2b4c boot TWRP3.1.0.0_ZUK_Z2_pro.img to boot in TWRP image
Go in backup and check all checkbox
Swipe to backup
Reboot the phone
From your computer browse your phone internal memory and copy your backup from TWRP/Backup/XXXXX to a directory in your computer
Step 6 : Install TWRP
In adb cmd enter adb reboot bootloader
Then fastboot flash recovery TWRP3.1.0.0_ZUK_Z2_pro.img to install TWRP on your phone
Then fastboot reboot
Then adb reboot bootloader
Then with volume keys select Recovery Mode and enter in Recovery Mode by pushing power key
TWRP will start
Reboot your phone
Step 7 : Install a custom ROM with TWRP
Download ROM from https://uploadfiles.io/55ffa
Copy paste ROM zip file in your phone internal storage
In adb cmd enter adb reboot bootloader
Then with volume keys select Recovery Mode and enter in Recovery Mode by pushing power key
Click Wipe and swipe to wipe. Do NOT reboot your phone.
Go back in TWRP main menu and click Install. Browse the ROM zip file
Swipe to install
Reboot your phone
When your phone reboot, it's in chinese. Click on the texte in the right bottom corner and then select your language.
During the phone configuration, do not connect wifi (in my case the phone configuration crashed when I connected to a wifi)
When you finished phone configuration reboot to get notification in your language
Step 8 : Install Gapps (google apps)
Download Gapps from https://forum.xda-developers.com/android/software/gapps-dynamic-gapps-t3487192
Copy the zip file in your phone
Reboot in TWRP
Install Gapps through TWRP
Reboot your phone
At this point my Google Play Services crashed each reboot. So needed to
Reboot in TWRP
Wipe cache
Now it works !
You can install other ROM with this method but I only tested with this one.
Enjoy
Click to expand...
Click to collapse
Does it works on Zuk Z2?
dommels said:
I'm currently on ZUI 2.5.x. Can I go straight to official MK60.1 using this guide?
Or should I downgrade to ZUI 2.3.x first
Click to expand...
Click to collapse
You can go straight to the latest RR rom without downgrade, so I guess you can do this with MK60 also. But why do you want that...?
Sendt fra min ZUK Z2121 med Tapatalk
Pendragon2000 said:
Does it works on Zuk Z2?
Click to expand...
Click to collapse
You can use this tutorial BUT you need to take a Z2 ROM and a Z2 TWRP.
Check on xda Z2 topics
accelerometer/gyroscope BUG can`t play any game
Notes About Xiaomi Mi Devices:
Some Xiaomi Mi devices have bootloaders that require additional steps to unlock before you are able to flash custom images. This typically involves filling out an application to have your device unlocked.
You will need to follow the steps on Xiaomi's MIUI website in order to unlock your device.
Understand that unlocking your device will wipe all of your personal data, settings, and apps from its memory.
TWRP Install (Requires TWRP 2.8.4 or higher already installed):
Download the latest TWRP image file (.img) from the download link and boot TWRP. Go to install and find and select the Images... button. Browse to the image that you downloaded and select it. Choose recovery and swipe to flash.
Fastboot Install Method (No Root Required):
You will need the platform-tools from the Android SDK on your computer. Find the Android command line tools section on the page linked and install the SDK tools package. From the SDK Manager, download only the platform-tools to get adb and fastboot binaries.
Windows users will need proper drivers installed on their computer. You can try the simple FWUL adb/fastboot ISO or the Naked ADB drivers or the Universal ADB drivers if you don't already have a working driver installed
On your device, go into Settings -> About and find the Build Number and tap on it 7 times to enable developer settings. Press back and go into Developer Options and enable USB debugging. From your computer, open a command prompt and type:
adb reboot bootloader
You should now be in fastboot mode.
Download the correct image file and copy the file into the same folder as your adb and fastboot binaries. Rename the image to twrp.img and type:
fastboot flash recovery twrp.img
fastboot reboot
Note many devices will replace your custom recovery automatically during first boot. To prevent this, use Google to find the proper key combo to enter recovery. After typing fastboot reboot, hold the key combo and boot to TWRP. Once TWRP is booted, TWRP will patch the stock ROM to prevent the stock ROM from replacing TWRP. If you don't follow this step, you will have to repeat the install.
dd Install Method (Requires Root):
Download the latest image file (.img) from the download link above. Place it in the root of your /sdcard folder and rename it to twrp.img. Run the following commands via adb shell or a terminal emulator app:
su
dd if=/sdcard/twrp.img of=/dev/block/bootdevice/by-name/recovery
#Download
dl.twrp.me/mido/twrp-3.2.1-0-mido.img
All credit goes to TWRP Devoloper
I am just share the file
abed0203 said:
Notes About Xiaomi Mi Devices:
Some Xiaomi Mi devices have bootloaders that require additional steps to unlock before you are able to flash custom images. This typically involves filling out an application to have your device unlocked.
All credit goes to TWRP Devoloper
I am just share the file
Click to expand...
Click to collapse
Thanks Thanks and once again, Thanks. It works fine with my RN 4 SD!
Please help me how to install twrp and root on redmi note 4x/mido miui 9.5.9.0...help me master...
ungah said:
Please help me how to install twrp and root on redmi note 4x/mido miui 9.5.9.0...help me master...
Click to expand...
Click to collapse
https://forum.xda-developers.com/re...p-step-guide-to-flash-android-n-beta-t3551221
Is it Treble supported?
Rifat Rezwan said:
Is it Treble supported?
Click to expand...
Click to collapse
I think this is a FAQ now. Official TWRP doesn't support Treble. There is a custom Treble version, which you can find a link to on the LOS 15.1 Treble threads.
You can also try OrangeFox TWRP, which supports Treble.
My phone, the LeEco Le Pro 3 LEX727 ZL1_NA US model is on the latest EUI 5.8.021S. I am able to open the adb tools in command prompt and get my computer to recognize my phone with "adb devices", but when I go to the stock fastboot with the Chinese and English writing and use "fastboot devices" nothing shows up. I'm using the latest adb tools and am clueless as to what to do.
Unlock Bootloader - Le Eco Pro 3
If you are not seeing your phone ID in ADB
Did you enable enable Developer options, or chosen MTP?
Its possible that the Android driver driver is outdated, or just try another usb port, preferably in the back of the machine.
Go here to check a whole list of possible causes: https://appuals.com/android-phone-not-showing-up-on-pc/
More than you asked for:
Since you seem to be new to your Leeco phone and new to using custom roms, I am going to go ahead and answer your current question and provide you steps needed to move forward. No big deal, I just copy pasted my notes ( with a few edits)
First steps that you need to take:
1. You will first need to unlock the bootloader :
PHP:
https://forum.xda-developers.com/showpost.php?p=71566961&postcount=203
2. Install Twrp :
PHP:
https://twrp.me/leeco/leecolepro3.html
****** Scroll down to see: Fastboot Install Method (
3. Right now just use ADB. But for the future, I highly recommend that you buy an OTG drive: it makes the whole process a thousand times easier: They are cheap somewhere near $5 and worth ten times that
Unlocking the Bootloader
You can save your self alot of time by looking up how to give ADB system wide privileges: this will allow you to flash files without tying the directory path.
Mauronofrio created a tool called: "TOOL ALL IN ONE"" it's great, install it and check for updates.
PHP:
https://toolaio.tk
The all is one tool is excellent and you can use it to install everything if wanted.
I usually recommend it for novices that can use it to help with unlocking the bootloader and installing TWRP.
The tool will also update your copy of ADB, android Drivers and provide system wide privileges for ADB
LETS RECAP : Choose using the All in One Tool or the ADB Method
**********BEFORE DOING ANYTHING*******************
Make sure you have enabled the developer tools,
Turned on USB debugging
Authorized your computer on your device I.E: “MTP”
Make sure the All in One Tool can see your device
(*) Select your device from the drop down menu, then click check
(*) Choose to install drivers, and set ADB and fastboot privileges from advanced menu.
(*) First attempt to unlock, then check bootloader status
If you have a X727 you will need to flash : emmc_appsboot.mbn from this zip :
PHP:
https://androidfilehost.com/?fid=313042859668275431
Next, choose Recovery flasher and manually select your copy of TWRP
After you have received the success message, I recommend doing the rest of the install manually within Twrp Recovery.
(*) Reboot into TWRP and begin installation of your Rom, Gapps and Magisk.
Using the ADB Method
Install ADB/Fastboot tools on your computer
PHP:
https://wiki.lineageos.org/adb_fastboot_guide.html
1. Make sure you have enabled the developer tools,
2. Turned on USB debugging, and authorized your computer on your device “MTP”
3. Enter fastboot mode on phone (hold power and VOL -)
4. Make sure adb can see your device when you run "adb devices"
5. type: fastboot devices
6. fastboot flash aboot emmc_appsboot.mbn
7. Run { adb reboot bootloader } - No spaces (before/after)
8. Run { fastboot devices } to make sure you see your device
9. Run { fastboot oem unlock-go } to unlock your device temporarily
10. Run { fastboot oem device-info } to verify unlock status
11. Run { fastboot boot recovery_twrp-3.2.1-0-zl1.img }
12. 5. Reboot back to TWRP and begin installation of your Rom, Gapps and Magisk.
13. 6. If you wiped data, your device will now proceed to re-initialize itself as if from the factory
Concerning your device's storage,
When you boot into twrp you will see a message that states that the storage is encrypted.
*****************Important************************ ******************
Ensure that you have TWRP installed as the primary recovery
Ensure that you have TWRP installed as the primary recovery
Ensure that you have TWRP installed as the primary recovery
Ensure that you have TWRP installed as the primary recovery
To remove encryption you will need to format the storage
(Anyone who says otherwise has the X720 and not the X727)
You could also try to skip the formatting step. But you will very likely have permissions issues and get errors and you will eventually have to come back and format ( Again as long as Twrp recovery is install there is very slim chance of ever bricking your phone.
To format the storage
Go to Wipe, choose Format Data and follow the instructions.
This will erase all of photos , music, etc
If you wiped your data partition, you'll need to push the zip file to the newly formatted storage. - This is one BIG reason why using OTG is better. You can use Mauronofrio's "TOOL ALL IN ONE"" for pushing the ROM, Gapps, and Magisk to storage.
Root: You absolutely should root!
NOTE: If you have unlocked the bootloader and flashed TWRP to the recovery partition. But have not yet flashed a Custom Rom the OS will likely reset back to the factory recovery UNLESS YOU ROOT THE SYSTEM. Your device is still unlocked. But the recovery can be overwritten by the stock EUI system, so beware.
Installation of Rom, Gapps, Magisk
Boot into TWRP recovery
1. Go to "Wipe" and then to "Advanced Wipe".
2. Mark "Dalvik / ART Cache", "System", "Data" and "Cache".
3. "Swipe to Wipe" and proceed back the main menu.
4. Go to "Install".
5. Select the ROM zip file and then press "Add more Zips" and select the Gapps zip file, and then the Magisk file.
6. "Swipe to confirm Flash" and wait for some time.
7. After the flashing is finished, just reboot to system.
Finished!
If you need help or have a question message me, I would much rather help you with a successful install versus helping you unbrick your phone.
Thank you for your reply. I figured out the issue. Windows 10 updater wasn't auto installing the driver for some reason even though I have auto update ticked.
simpbrackets said:
Thank you for your reply. I figured out the issue. Windows 10 updater wasn't auto installing the driver for some reason even though I have auto update ticked.
Click to expand...
Click to collapse
You have manually install those drivers usually.
Sent from my LEX720 using xda premium
I have the same issue in Windows 10. All In One Tool sees my x720 in adb mode, but when I switch to bootloader, the phone is gone. Device manager then shows unrecognized android device. I have LTSB version of Windows, so maybe that's why it won't auto install the needed driver. Could anyone point out what kind of driver exactly do I need, so that I can install it manually?
I wanted a Linux and Android in the same Cellphone. About Android, it's a Linux but with difference and it has all the features. Let's know 'how can we boot Ubuntu Touch and Android in the same Cellphone'.
1. First of all we need to unlock the bootloader of our device.
2. ADB and Fastboot drivers must be installed. Or you can download Android SDK Platform tools .
3. USB-Debugging must be enabled.
4. Connect phone with PC via USB. Reboot phone to fastboot mode (Volume-down + Power).
5. Drop the recovery image into the adb folder and open command prompt.
6. Enter the following commands:
Code:
fastboot devices
fastboot flash recovery recovery.img
fastboot reboot
TWRP 3.3.1-1
[If you already have custom recovery then just skip.]
7. Reboot to recovery (Volume-Up + Power; release Power when phone turns on, keep holding Volume-Up until you see screen of TWRP). If TWRP asks for PIN, enter the PIN of your unlock screen.
8. Wipe > Cache and System from Advanced Wipe. Format Data > Yes. Now reboot to recovery.
9. Flash firmware and vendor arm64.
10. Flash any Android GSI ARM64-AB. (I flashed AOSP ARM64-AB GO)
11. Flash Ubuntu Touch GSI. It works in arm64 a/ab.
12. Now which one you want to boot. If you want to boot Ubuntu Touch then flash Halium_Boot, if you want Android then Android_Patched_Boot, it's your choice.
Credits :
erfanoabdi (ubport gsi)
nikp123 & YaAlex (arm64 kernel)
Phhusson (AospGo GSI)
TheGame455 (firmware and vendor)
Khushraj Rathod (VoLTE Fix)
VoLTE-Fix for Android
VoLTE is not working in Ubuntu Touch GSI
Ubuntu Touch Passphrase : phablet
Special thanks to Canonical Ltd, ubport and Xiaomi.
Thanks
Is it possible to install only UBuntu Touch in this phone, without Android?
Jazzda said:
Thanks
Is it possible to install only UBuntu Touch in this phone, without Android?
Click to expand...
Click to collapse
What you want, GSI isn't good! It takes data partition.
Some people can not understand dual boot means you can keep both, and if you don't want another then just skip that part and only flash one.
First having a Custom Recovery
1. Unlocked Bootloader of Phone.
2. ADB and Fastboot drivers must be installed on PC/Laptop.
3. USB Debugging Enabled in Phone.
4. Connect phone with PC via USB.
5. Reboot phone to fastboot mode (Volume-down +Power).
Or Open command prompt in adb folder and type :
adb devices
adb reboot bootloader
6. Place the recovery image into the adb folder. Enter the following commands:
fastboot devices
fastboot flash recovery recovery.img
fastboot reboot
[Note: If you already have custom recovery then skip above.]
Installation Guide:
1. Reboot to recovery (Volume-Up + Power).
2. Wipe > Cache and System from Advanced Wipe. Format Data > Yes. Now reboot to recovery.
3. Flash firmware and vendor arm64.
Ubuntu Touch
4. Flash Ubuntu Touch GSI.
Android
5. Flash any GSI of ARM64-AB of Android.
6. Flash Boot Image.
Switching OS between Ubuntu and Android : Just keep both the Boot Zip file in storage and flash whichever you wanna boot.
Downloads :
TWRP Recovery
fw-vendor-arm64_pine_11.0.11_GLOBAL
For Ubuntu
Halium_Boot_Pine
Ubuntu Touch GSI
For Android
Redmi7A_patched_boot_11.0.11global_64bit
AOSP ARM64-AB GO
[AOSP GO GSI of Phhusson is working smoothly and takes less space, because it's go-edition.]
I think it's clear now, thanks
fw-vendor 11.0.11 vs 10.2.5, what's the difference and/or whats best?
i followed the steps after reboot the screen is stuck in fastboot mode.where to download hallium boot the link is broken
redmikos said:
i followed the steps after reboot the screen is stuck in fastboot mode.where to download hallium boot the link is broken
Click to expand...
Click to collapse
It's illegal to share kernel without copyright, so there is no sharing buddy, search it somewhere else. These days gpl, gnu has changed their definition. In past you could share without any restriction but not now. So why should I share them and get caught in legal proceedings.
You got it now!
at first thank you very much,are you still working on it? i have problem while record video, actually when i try to open the file, it looks corrupt and i can't run it, can i try to change some setting?sometime it work sometime no, i don t know why