I'm good to follow directions, I can't troubleshoot. Hopefully someone here can give me some direction. All info below. TIA!
Samsung S7 Edge.
Originally Verizon.
Used Odin to reflash TMobile
Worked fine for months.
Went to reflash to Verizon or unlocked.
(Perhaps it partially worked if that's possible as its listed as G935u now?)
Phone is stuck in loop.
I cannot turn the phone off using the power button.
Only battery drain will power it down.
Once charged and on, can only get out of the loop by entering power/home/ Vdown.
If I press Home: I get barcodes, check.
If I press Volume Down, Cancel
Black Screen:
Recovery Booting small blue letters...
"installing system update" blue screen, android man, two circling arrows.
Black screen flash, repeat.
or eventually/sporadically:
"no command"- blue screen tilted Android Guy with Exclamation mark in triangle
If I choose volume up: Continue
Teal screen
Top Text :
Odin Mode (high speed)
Product Name SM-G935U
Current Binary: Samsung Official
System Status: Official
FRP Lock: Off
Warranty Void: 0x0
Qualcomm Secureboot: Enable
RP SWREV: B9(2,1,1,1,1) K9 S9
Secure Download: Enable
Screen: Downloading.....do not turn off target
I can connect odin.
In Odin 3.13 trying to flash full firmware (AP/BP/CP/CSCHome):
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 5463 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> emmc_appsboot.mbn
<ID:0/003> lksecapp.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/00>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1
On phone in red: SW Rev Check Fail: [aboot] Fused 9 > Binary 4
In Odin trying to flash TWRP if this is even possible.
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 43 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
On phone in red: Secure Check Fail: Recovery
~
maxweenus said:
On phone in red: SW Rev Check Fail: [aboot] Fused 9 > Binary 4
Click to expand...
Click to collapse
You need a more recent firmware file to flash.
This one will do the job: https://androidfilehost.com/?fid=6006931924117927499
bbsc said:
You need a more recent firmware file to flash.
Amazing. Thank you so much!
Curiosity- If I want to switch this back to Verizon per se, where can I find the updated firmware such as what you linked.
Probably a rookie move, but I've been sitting on Sammobile waiting a day and a half to download.
Click to expand...
Click to collapse
maxweenus said:
If I want to switch this back to Verizon per se, where can I find the updated firmware such as what you linked.
Click to expand...
Click to collapse
I think, the best way is to start here: https://www.verizonwireless.com/support/samsung-galaxy-s7-update/
They have a special "updater" tool which can "recover" your device.
Related
It's been a long day... Let me start by saying that i had my device rooted for a month without any issues. Last night, i noticed some apps were killing themselves for some reason but i didnt give it much thought. This morning while i was working, i noticed the phone app was crashing and not responding, so i decided to restart it. It ended up getting stuck on the T-Mobile boot screen. I tried to boot it into recovery mode, but it wasn't the normal recovery mode. It didnt give me option to scroll up and down with the volume keys. It's just a black screen with:
RECOVERY BOOTING......
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-G935T
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
FRP LOCK: OFF
WARRANTY VOID: 0x0
QUALCOMM SECUREBOOT: ENABLE
HP SWREV: B3(2,1,1,1,1) K1 S2
SECURE DOWNLOAD: ENABLE
It just stays on this screen until i power the device off, and it goes right back into a bootloop. Also, i can't boot into safe mode either.
So, I figured I would try to flash the stock firmware with Odin. I downloaded the firmware and tried to flash it and got this error:
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I did some searching and found that i might need to flash a .pit file, so i found the one for my device and put in in Odin. I tried to flash it and got this error:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
At this point, I have no idea what to do or try. I need my phone for work and ive already missed today. If anyone has any advice, it would be greatly appreciated!!!!!
tylerthedestroyer42 said:
It's been a long day... Let me start by saying that i had my device rooted for a month without any issues. Last night, i noticed some apps were killing themselves for some reason but i didnt give it much thought. This morning while i was working, i noticed the phone app was crashing and not responding, so i decided to restart it. It ended up getting stuck on the T-Mobile boot screen. I tried to boot it into recovery mode, but it wasn't the normal recovery mode. It didnt give me option to scroll up and down with the volume keys. It's just a black screen with:
RECOVERY BOOTING......
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-G935T
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
FRP LOCK: OFF
WARRANTY VOID: 0x0
QUALCOMM SECUREBOOT: ENABLE
HP SWREV: B3(2,1,1,1,1) K1 S2
SECURE DOWNLOAD: ENABLE
It just stays on this screen until i power the device off, and it goes right back into a bootloop. Also, i can't boot into safe mode either.
So, I figured I would try to flash the stock firmware with Odin. I downloaded the firmware and tried to flash it and got this error:
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I did some searching and found that i might need to flash a .pit file, so i found the one for my device and put in in Odin. I tried to flash it and got this error:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
At this point, I have no idea what to do or try. I need my phone for work and ive already missed today. If anyone has any advice, it would be greatly appreciated!!!!!
Click to expand...
Click to collapse
We need just a bit more info bro. What firmware you attempting to flash? And what firmware was already on the device? If you're on OTA would be good to note as well..
Sent from my SM-G935T using Tapatalk
tylerthedestroyer42 said:
It's been a long day... Let me start by saying that i had my device rooted for a month without any issues. Last night, i noticed some apps were killing themselves for some reason but i didnt give it much thought. This morning while i was working, i noticed the phone app was crashing and not responding, so i decided to restart it. It ended up getting stuck on the T-Mobile boot screen. I tried to boot it into recovery mode, but it wasn't the normal recovery mode. It didnt give me option to scroll up and down with the volume keys. It's just a black screen with:
RECOVERY BOOTING......
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-G935T
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
FRP LOCK: OFF
WARRANTY VOID: 0x0
QUALCOMM SECUREBOOT: ENABLE
HP SWREV: B3(2,1,1,1,1) K1 S2
SECURE DOWNLOAD: ENABLE
It just stays on this screen until i power the device off, and it goes right back into a bootloop. Also, i can't boot into safe mode either.
So, I figured I would try to flash the stock firmware with Odin. I downloaded the firmware and tried to flash it and got this error:
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I did some searching and found that i might need to flash a .pit file, so i found the one for my device and put in in Odin. I tried to flash it and got this error:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
At this point, I have no idea what to do or try. I need my phone for work and ive already missed today. If anyone has any advice, it would be greatly appreciated!!!!!
Click to expand...
Click to collapse
You need check at "re-partition" in Option Tab, and in PIT Tab, you download PIT of G935T, browser it then flash with your ROM via Odin together. Magic is happening )
http://www.sammobile.com/forum/showthread.php?t=30628
Same issue here
I've tried to flash stock 4APIA to my SM-G935T TMO S7 Edge and I have not been able to get it to work. I am about to try the pit file, partition check and full 4 files to see if it will work now, I will keep you posted.
Have you been able to resolve the issue?
So I wanted to root my phone tonight and thought I was doing everything right, well my phone rebooted and wouldn't connect to my carrier or anything and was checking device status the entire time..
So I decided to reboot and now I am just even more confused.. my phone at the current state is relooping into the recover reboot stage.. so I can't put the phone in USB debugging or anything like some post suggest..
I can get it to download mode but every time I try odin it fails and fails.. I have tried everything to my ability to get this phone to reboot on stock and I just cant seem to figure it out..
I am not to knowledgeable about ROM's and rooting and such and I learned my lesson.
When on the download screen is says at the bottom in red text " SW REV CHECK FAIL : [aboot] Fused 4 > Binary 2
This is the error code I get from Odin when trying to flash back to oem android on my S7 EDGE
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> emmc_appsboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> lksecapp.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I am more then open to any suggestions I just want my phone back lol
My G930A will no longer turn on. When I try to boot it into recovery, it shows the blue letters saying 'recovery booting' then, it shows a blue screen with the android logo that says 'installing system update'. It will switch between those screens over and over and sometimes boots into recovery but the screen is frozen so i cant do anything there. I am still able to boot into download mode though. the firmware version was G930AUCS8CRL1. I was able to flash the G930AUCS8CRJ2_ATT8CRJ2 firmware that is linked on xda, but it still has the same issues.
When I try to flash G930AUCU4CRE4_Oreo on Odin, it says:
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 5815 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> emmc_appsboot.mbn
<ID:0/003> lksecapp.mbn
<ID:0/003> xbl.elf
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
As background, I had some success with rooting my device when it was in nougat, but I decided to revert to stock. I'm not sure if this is a residual effect of that...
This is what it says on the download screen:
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-G930A
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
FRP LOCK: OFF
WARRANTY VOID: 0x0
QUALCOMM SECUREBOOT: ENABLE
SECURE DOWNLOAD : ENABLE
Any help is greatly appreciated
Recovery Menu
Rasmubur000 said:
My G930A will no longer turn on. When I try to boot it into recovery, it shows the blue letters saying 'recovery booting' then, it shows a blue screen with the android logo that says 'installing system update'. It will switch between those screens over and over and sometimes boots into recovery but the screen is frozen so i cant do anything there. I am still able to boot into download mode though. the firmware version was G930AUCS8CRL1. I was able to flash the G930AUCS8CRJ2_ATT8CRJ2 firmware that is linked on xda, but it still has the same issues.
When I try to flash G930AUCU4CRE4_Oreo on Odin, it says:
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 5815 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> emmc_appsboot.mbn
<ID:0/003> lksecapp.mbn
<ID:0/003> xbl.elf
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
As background, I had some success with rooting my device when it was in nougat, but I decided to revert to stock. I'm not sure if this is a residual effect of that...
This is what it says on the download screen:
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-G930A
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
FRP LOCK: OFF
WARRANTY VOID: 0x0
QUALCOMM SECUREBOOT: ENABLE
SECURE DOWNLOAD : ENABLE
Any help is greatly appreciated
Click to expand...
Click to collapse
Replied in other thread as well, but I believe you need to use the key combo to access recovery.
After the screen with the blue letters that say "booting recovery" give it about 10 - 30 seconds and press and hold power while you tap (press and release) volume up, then release power. That will open your recovery menu.
Factory reset and should be good
Cheers and best of luck
Feel free to PM me if that doesn't work.
I have replaced the cracked display and after the replacement, Samsung logo is stuck on the screen. According to the guy from the repair shop, a firmware update is necessary. So I have downloaded the file from here:
https://www.sammobile.com/samsung/galaxy-note-3/firmware/SM-N9005/TMS/download/N9005XXSGBRI2/244008/ and followed the instructions on the site (install Odin, boot in download mode, start update). The update failed with the following message on the screen:
ODIN MODE
PRODUCT NAME: SM-N9005
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
REACTIVATION LOCK: Official
KNOX WARRANTY VOID: 0x0
QUALCOM SECUREBOOT: ENABLE (CSB)
AP SWREV: S2, T2, A2, A3, P3
SECURE DOWNLOAD: ENABLE
UDC START
Volume size is too big 122880 < 409600
ODIN: invalid ext4 image
Log from Odin:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1401)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 2288 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> sdi.mbn
<ID:0/004> NON-HLOS.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> cache.img.ext4
<ID:0/004> hidden.img.ext4
<ID:0/004> FAIL! (Ext4)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have searched XDA forums and found advice to use PIT file. Among others, I've used this one: https://forum.xda-developers.com/showthread.php?t=2503547
After firmware update with PIT file there is the same error in Odin:
Log:
<ID:0/004> Odin engine v(ID:3.1401)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 2288 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> sdi.mbn
<ID:0/004> NON-HLOS.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> cache.img.ext4
<ID:0/004> hidden.img.ext4
<ID:0/004> FAIL! (Ext4)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Now after a reboot following message appears on screen: Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.
- I have installed "Smart Switch PC" version 4.1.17054_16 (since this is the last one that supports "Emergency software and initialization")
- Opened the tab "Device Initialization"
- search for model name: SM-N9005
- type in serial number
The dialog says: SM-N9005 does not support initializing. Please contact our service center.
Any suggestions on what to do next? I just want a functioning phone, I do not need any custom roms/bootloaders/unlocks. Thank you.
https://www.sammobile.com/forum/threads/35929-SOLVED-firmware-flashing-FAIL-after-hidden-img
https://www.google.com/search?client=firefox-b-d&q=odin+fail+at+hidden.img
Thank you for the tip. This helped me with the error " Firmware upgrade encountered an issue" now I am back at the "Samsung Galaxy Note3" logo. Booting into recovery mode also does not work as the logo stays on the screen with the message "RECOVERY BOOTING...". So I am back at the beginning. When I was troubleshooting the issue I was searching for "Samsung galaxy note3 stuck on logo screen" (and its variations), or searching for error messages from the logs. Maybe I am asking the wrong questions. Is flashing the firmware the right way to fix my problem that was originally caused by replacing the broken display?
just find a stock android 5.0 flash it with odian in download mode. a replacement screen shouldn't do that to your phone unless the screen u paid for is fake or incompatible with your note 3.
Hi,
My phone is stuck on twrp loading screen. Reboot again lands on the same screen.
I even tried flashing the stock rom(sammobile) via odin but fails everytime
Here is the log:
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4245 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
On the Downloading screen:
Odin mode
download speed: fast
system status: official
FRP lock: off
After the stock rom fail via odin, this mesg appears:
KERNAL REV. CHECK FAIL, DEVICE: 5, BINARY: 0
I tried various solutions but nothing seems to work. Please help me!
use correct restore and correct usb cable, oh and another rom
SonyXperiaS said:
Hi,
My phone is stuck on twrp loading screen. Reboot again lands on the same screen.
I even tried flashing the stock rom(sammobile) via odin but fails everytime
Here is the log:
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4245 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
On the Downloading screen:
Odin mode
download speed: fast
system status: official
FRP lock: off
After the stock rom fail via odin, this mesg appears:
KERNAL REV. CHECK FAIL, DEVICE: 5, BINARY: 0
I tried various solutions but nothing seems to work. Please help me!
Click to expand...
Click to collapse
Same problem here, did you fix it?
Use the correct bootloader binary, the one you trying to flash is lower then currently installed on your phone.
Try flashing with the version 5 binary roms as displayed in your download mode.