I see this is a very common problem with these phones. Except mine had snapped in half, and I was barely able to get the microSD card out. Now my SIM is stuck inside, along with the lower half of the tray. Issue is it's no longer under warranty. I've tried a few things, like holding it upside down and lightly thumping the top of the back/front with my palm. but that ****er just won't pop out. I'm leery of sticking anything inside there for fear of damaging anything, let alone attempting to pull it out with a cut credit card and a sliver of glue. I'm thinking I'll take it to a repair shop, but I heard that once it's taken apart, it loses its waterproof seal. Can anyone confirm this? Or offer some other advice?
GuyInDogSuit said:
I see this is a very common problem with these phones. Except mine had snapped in half, and I was barely able to get the microSD card out. Now my SIM is stuck inside, along with the lower half of the tray. Issue is it's no longer under warranty. I've tried a few things, like holding it upside down and lightly thumping the top of the back/front with my palm. but that ****er just won't pop out. I'm leery of sticking anything inside there for fear of damaging anything, let alone attempting to pull it out with a cut credit card and a sliver of glue. I'm thinking I'll take it to a repair shop, but I heard that once it's taken apart, it loses its waterproof seal. Can anyone confirm this? Or offer some other advice?
Click to expand...
Click to collapse
With fricking care I put a drop of super glue on a toothpick and fished mine out is how I did mine 3 times. I've broke 4 trays. I got a feeling it's something to do with sd cards ever since I quit using a SD card I haven't broke not 1. It's a punk ***** and I don't know why Samsung wouldn't use the metal ttys like in the past. I have several posts on this issue myself.
Yes once disassembled you lose the water proofing. I had to send mine in for warranty and needed my sim out of it obviously. And those tards of coarse said of the tray is broke the warranty was voided so I did everything in my power to remove it. But I did 3 times over
TheMadScientist said:
With fricking care I put a drop of super glue on a toothpick and fished mine out is how I did mine 3 times. I've broke 4 trays. I got a feeling it's something to do with sd cards ever since I quit using a SD card I haven't broke not 1. It's a punk ***** and I don't know why Samsung wouldn't use the metal ttys like in the past. I have several posts on this issue myself.
Yes once disassembled you lose the water proofing. I had to send mine in for warranty and needed my sim out of it obviously. And those tards of coarse said of the tray is broke the warranty was voided so I did everything in my power to remove it. But I did 3 times over
Click to expand...
Click to collapse
I'm very leery of using anything to do with glue, to be honest. Though that looks like I will have to do exactly that, unfortunately.
GuyInDogSuit said:
I'm very leery of using anything to do with glue, to be honest. Though that looks like I will have to do exactly that, unfortunately.
Click to expand...
Click to collapse
I mean I literally used like a quarter drop on the very top tip. The credit card idea seams even better a bit more surface area. The second time my tray got stuck totally and I bit the bullet and forced it out and it split in the middle between the SD and sim. Left the second half in it. The eject button doesn't work any more when I put my tool in now I have to angle it and pull. I haven't broke it now in like 6 months since I put my SD card in my Ps vita
I have never rough housed mine in the end I have probably removed my trays about 15 times since owning this device.
This is one of the biggest flaws with this device imo and I can't find a compatible aluminum tray anywhere
Could try pinching it out with two sewing needles?
Have done this with an iPhone for someone before. :crying:
Just make sure phone's off to avoid shorting anything...
CoreyOS said:
Could try pinching it out with two sewing needles?
Have done this with an iPhone for someone before. :crying:
Just make sure phone's off to avoid shorting anything...
Click to expand...
Click to collapse
I'm gonna get a pair of eyebrow pluckers, or whatever you call those really thin tweezers, and try to pluck it out that way. There is a small part of one side that is close to the top of the slot (as it broke off... diagonally, sort of), so hopefully I can grab ahold of that.
GuyInDogSuit said:
I'm gonna get a pair of eyebrow pluckers, or whatever you call those really thin tweezers, and try to pluck it out that way. There is a small part of one side that is close to the top of the slot (as it broke off... diagonally, sort of), so hopefully I can grab ahold of that.
Click to expand...
Click to collapse
Fingers crossed!!!
No such luck. It's really hard to see in there and even with a bright light and magnifying glass, I can't seem to find it. Looks like I'll have to take it to a repair shop and lose the waterproof seal, since they'll have to take it apart.
GuyInDogSuit said:
No such luck. It's really hard to see in there and even with a bright light and magnifying glass, I can't seem to find it. Looks like I'll have to take it to a repair shop and lose the waterproof seal, since they'll have to take it apart.
Click to expand...
Click to collapse
I guess I got lucky. Food for thought after the fact. Get a LifeProof case. Their water proof at least give back some of the resistancy. That's what I got on mine... I swapped frames and screens on Mine
get a new glass back with the ip68 tape. cost around $10 and waterproofing stays intact. pull the old one off and just make sure you clean the bonding area well.
I've done this 2x with mine and have no issues with water intrusion.
triumvirant said:
get a new glass back with the ip68 tape. cost around $10 and waterproofing stays intact. pull the old one off and just make sure you clean the bonding area well.
I've done this 2x with mine and have no issues with water intrusion.
Click to expand...
Click to collapse
Can you point me in the direction of a tutorial? For future reference and for anyone else who may have to do this as well? I've already had mine repaired and all's well, but I think this info would come in handy for others (including me if it happens again). The fact that people are having to do stuff like this multiple times with their phones is rather frightening.
GuyInDogSuit said:
Can you point me in the direction of a tutorial? For future reference and for anyone else who may have to do this as well? I've already had mine repaired and all's well, but I think this info would come in handy for others (including me if it happens again). The fact that people are having to do stuff like this multiple times with their phones is rather frightening.
Click to expand...
Click to collapse
Not sure on the rules for posting links, but if you search youtube for "S8 back glass replacement" you can find plenty of videos. I personally used the ifixit teardown guide just to familiarize myself with any cables or things to watch out for.
For the back glass itself, just make sure you get one with the camera lens pre-installed and with ip68 tape. Price for the one i bought is currently $10.02 on ebay.
TheMadScientist said:
I guess I got lucky. Food for thought after the fact. Get a LifeProof case. Their water proof at least give back some of the resistancy. That's what I got on mine... I swapped frames and screens on Mine
Click to expand...
Click to collapse
Yeah. I will second this. I do all my own repairs. But in this case I just don't care. I'm not interested in reselling. Or anything. This will be a backup in a few months. Time to move on. ???
It stays in the lifeproof so it's water resistant and I don't have to see it.
Solved!
1) Heat a needle, or a tiny flathead screwdriver, and stick it in.
2) Wait 1 minute.
3) Pull out needle or screwdriver to find sim attached and out!
Related
Anyone had problems with the battery cover? I took mine off when I first got it and when I tried to put it back, it only clipped into 3 corners, 1 was loose and slide on and off so was never flush.
I've sent it back to Mobilephonesdirect for them to "assess" and see if a replacement is needed. Bloody hope so, its faulty!
Nope, no problems here although i had to open & close the cover several times to reset the device.
Other than finding it the worst battery cover design ever made by HTC, no. I did notice that when putting it back on you put the right side in first and then snap it all down evenly, that it left one corner up and it simply needed a gentle push and it all went flush.
I am concerned about the long term use of the cover, it is difficult to get on and off at best and certainly not designed for ease of use.
The cover is metal but the phone it snaps onto is plastic....and the plastic contact points will wear, that's if the metal battery cover itself doesn't relax its shape a little and get less tight. It seems a bad solution to me but HTC aren't alone in this, I see that battery covers are becoming cheaper and nastier across all brands. At least the HTC cover is metal. I try not to remove my cover...ever.
Yeah, it's a little tight for my liking, if you swap out the sim or memory card a lot it could cause problems. Second battery too.
Hopefully the back case will be available to buy somewhere. It must cost pennies to make.
arfster said:
Hopefully the back case will be available to buy somewhere. It must cost pennies to make.
Click to expand...
Click to collapse
Yeah, but they'll probably be available on eBay for about £25, despite that.
I thought I was doing something wrong when I could not budge mine.
On a new phone it takes quite a bit of brute force.
battery cover
Yep, mine stays up on one corner too. Just a little nudge and its back on flush!
Technique is King
Everything requires a technique, then it becomes easy!.
Really all one needs to do is slide your thumbnail under the cover's edge; from one end to the other till there is a millimeter gap, then voila! simply pull off!
If you try to pull it off using the indented 'tab' then good luck to you, Frustration Guaranteed!
sunking101 said:
I try not to remove my cover...ever.
Click to expand...
Click to collapse
Unforyunately my phone already got stuck a couple of times and the only way to bring it to live again was removing the cover and soft reset or remove the battery.
A shame that the reset button is not reachable from the outside. It might be easy to make a small hole in the cover right above the reset button.
nicelad_uk said:
Anyone had problems with the battery cover? I took mine off when I first got it and when I tried to put it back, it only clipped into 3 corners, 1 was loose and slide on and off so was never flush.
I've sent it back to Mobilephonesdirect for them to "assess" and see if a replacement is needed. Bloody hope so, its faulty!
Click to expand...
Click to collapse
I had the same problem with the cover on mine. I found that I must have slightly bent the cover when i first removed it, when i bent it back (to make the fit a bit tighter) it never happend after that.
sunking101 said:
I try not to remove my cover...ever.
Click to expand...
Click to collapse
I will try not too. However if the phone locks up I'll have no choice but to remove the cover and press the red button.
ya i also think the battery cover is design in a wrong way
it took me awhite to open it...
u know i scare i open to hard will spoilt it
Some of the covers are a bit loose. Thank goodness the shop I bought it from, replaced mine for me.
I was thinking maybe I could take off that bottom "HTC" cover and gently pinch the sleeve of the USB connector back together. Anyone successfully done this?
Thanks!
this is exactly why i use the dock & WANT the car dock..
It just pops off, Google for a tear down.
I'm in the middle of taking mine apart to clean dust from the screen. Can't get a warranty replacement cause the phone is rooted. The bottom piece is a real pain to take off, but can be done with some patience. Just make sure to use a plastic tool and not a screwdriver. I used the ifixit teardown guide and a youtube teardown guide.
Quick question, how long was it before you got dust under the screen? Also did you notice any signs such as the screen not being totally flush with the housing? I really need to know because I'd like to root my N1 but it's only been a month. Also from what I've seen around the forum there is a gentlemen that can help you get a warranty from HTC but idk about now that you've opened the phone
dhendrix11 said:
I'm in the middle of taking mine apart to clean dust from the screen. Can't get a warranty replacement cause the phone is rooted. The bottom piece is a real pain to take off, but can be done with some patience. Just make sure to use a plastic tool and not a screwdriver. I used the ifixit teardown guide and a youtube teardown guide.
Click to expand...
Click to collapse
Did you try to get a replacement and were refused because you are rooted or did you not try because you knew you would be refused?
mafaesto said:
Quick question, how long was it before you got dust under the screen? Also did you notice any signs such as the screen not being totally flush with the housing? I really need to know because I'd like to root my N1 but it's only been a month. Also from what I've seen around the forum there is a gentlemen that can help you get a warranty from HTC but idk about now that you've opened the phone
Click to expand...
Click to collapse
Had my phone a couple months before I noticed any dust. The bottom left corner (where there was dust) seems like maybe it's sealed as 100% as the other corners, but nothing obvious at all and no clicking sound type stuff that others have reported. I posted some pictures in the dust thread.
irishrally said:
Did you try to get a replacement and were refused because you are rooted or did you not try because you knew you would be refused?
Click to expand...
Click to collapse
I told them I'd rooted and they guy said my warranty was void. Said I could send it in and there's a chance that they would take it, but also that they could charge me for a board swap, which is $196. He couldn't give me a certain answer how it would be handled. Said that they take care of the warranty service in their Houston location, which wasn't where he was at, so he couldn't find out for sure.
I have dust on the side of my screen. One white speck just to annoy me. I wouldnt mess with taking it apart in fear that i might add even more dust underneath
dhendrix11 said:
I told them I'd rooted and they guy said my warranty was void. Said I could send it in and there's a chance that they would take it, but also that they could charge me for a board swap, which is $196. He couldn't give me a certain answer how it would be handled. Said that they take care of the warranty service in their Houston location, which wasn't where he was at, so he couldn't find out for sure.
Click to expand...
Click to collapse
I dont get why people are doing this. If it was me, I'd keep quiet about the bootloader's status and see if they notice.
It's not like you can hide the telltale padlock.. It's there for a reason. HTC made it easy too see if you voided the warranty.
Indeed you can't, but the technicians may not care, or even be paying attention when it boots up and miss it, or even not bothering to turn it on for something like a dusty screen.
Rusty! said:
I dont get why people are doing this. If it was me, I'd keep quiet about the bootloader's status and see if they notice.
Click to expand...
Click to collapse
I was told that if they notice, they'd likely charge my card $196 to replace the main PCB. The other alternative was that they'd call me back and tell me the warranty was void and send my original phone back and have me send back the replacement. Either way, I have to wait til that all plays out before I could root the replacement phone and get it set back up like my original. Instead, I spent two hours with the phone I've got and the screen looks like new.
dhendrix11 said:
Had my phone a couple months before I noticed any dust. The bottom left corner (where there was dust) seems like maybe it's sealed as 100% as the other corners, but nothing obvious at all and no clicking sound type stuff that others have reported. I posted some pictures in the dust thread.
Click to expand...
Click to collapse
I appreciate the response I'll check it out, I am just extremely worried. At the same time, I have never had my phone replaced. I usually just work on them myself for all those simple problems. I don't know that my screen is sealed properly, it clicks occasionally but hasn't been lately. But it definitely doesn't sit flush with the right side..
starkruzr said:
I was thinking maybe I could take off that bottom "HTC" cover and gently pinch the sleeve of the USB connector back together. Anyone successfully done this?
Thanks!
Click to expand...
Click to collapse
Maybe this would help , if you dont fix it ...
http://cgi.ebay.com/Nexus-One-Port-...ZViewItemQQptZCell_Phones?hash=item5886e20fb8
Good luck ...
50 bucks for a standard micro USB port? That's daylight robbery, any electronics supplier will have for peanuts!
Has there been a decent guide on taking the 4G apart yet? I've googled it but haven't been able to find anything yet.
kitsunisan said:
Has there been a decent guide on taking the 4G apart yet? I've googled it but haven't been able to find anything yet.
Click to expand...
Click to collapse
I cant fine one either but there are 2 screws in the battery compartment and it looks like the metal portion where the camera is may pop or peel off with a little force. My guess, try to remove metal portion where camera is, if it comes off and exposes screws remove those along with 2 in bat compartment then use tool to try and separate where bezel and rubber surround are. Just fumble it.
May I ask why your taking it apart?
Stupid reason really, I was going to see if the ffc could be centered better. Seems just about all of the MT4G phones have an off-centered camera, and wanted to see if I could move it back to center myself. I was just curious to see what was throwing it off.
I had the two screws off last night, but couldn't get anything to come off. Didn't want to force it and break anything, I was just hoping a teardown had been done showing what needed to be done.
kitsunisan said:
Stupid reason really, I was going to see if the ffc could be centered better. Seems just about all of the MT4G phones have an off-centered camera, and wanted to see if I could move it back to center myself. I was just curious to see what was throwing it off.
I had the two screws off last night, but couldn't get anything to come off. Didn't want to force it and break anything, I was just hoping a teardown had been done showing what needed to be done.
Click to expand...
Click to collapse
I don't think a phone exists that you dont have to pry, push, pull and force things to get them apart. There will ALWAYS be risk of breaking things when taking a phone apart. I would just deal with it and not open the phone. Plus, they usually have a way to tell if you've opened your phone so you will void your warranty.
There is a "void" sticker on one of the screws. If someone does open her up, check to see if you could replace the speaker with a better one from another phone.
Please post questions in Q&A section.
I'm curious to learn how to take the phone apart as well, because I'd like to figure out how to make the damn buttons stop squeaking & clicking so loudly (home/menu/back/genius). It's driving me insane and I'm already on my third MT4G.
dustrho said:
I'm curious to learn how to take the phone apart as well, because I'd like to figure out how to make the damn buttons stop squeaking & clicking so loudly (home/menu/back/genius). It's driving me insane and I'm already on my third MT4G.
Click to expand...
Click to collapse
Anyone? I'm now on my fourth MT4G and will be receiving a fifth one shortly (creaking buttons), and if I experience that same problem I'm thinking about trying to fix the damn thing myself.
damn still no tear down i need one buttons jammed
I tore one apart after I got pissed and threw it into the hardwood floor at full speed.
I don't remember the steps but I do remember there are a couple key points, including ribbons that have to be disconnected. The ribbon connector from the main display to the main board is junk and that, of all places, is where my tear down went south.
I've got 450.00 dollars sitting in pieces if anyone wants to see them.
Sent From My Rooted HTC Glacier- It Just Makes SENSE
pdxrealtor said:
I tore one apart after I got pissed and threw it into the hardwood floor at full speed.
I don't remember the steps but I do remember there are a couple key points, including ribbons that have to be disconnected. The ribbon connector from the main display to the main board is junk and that, of all places, is where my tear down went south.
I've got 450.00 dollars sitting in pieces if anyone wants to see them.
Sent From My Rooted HTC Glacier- It Just Makes SENSE
Click to expand...
Click to collapse
I'm looking to buy someones Part "Power Ribbon Cable Assembly" (The part thats connected to the power button) *BE CAREFULLY" Everything has to be in Working order and not torn! Send me photos of the part I'm looking for and price. [email protected] Thanks!
dustrho said:
Anyone? I'm now on my fourth MT4G and will be receiving a fifth one shortly (creaking buttons), and if I experience that same problem I'm thinking about trying to fix the damn thing myself.
Click to expand...
Click to collapse
You must never have had a MT3G. These buttons are a dream compared to the creaky clickers in that dog.
I bought a refurbished phone on Craigslist and there are fingerprints on the inside of the glass (I don't know why I never saw them when I was inspecting). Would like to teardown guide so I can go clean those prints off.
Lil bit of thread necromancy here, but did anybody ever find a teardown? I'm thinking of ripping mine open due to my backlight issue ( http://forum.xda-developers.com/showthread.php?t=958033 ). I guess if nobody else has a teardown, I'll have to brave the waters and post my own, but going in blind is going to increase the risk of me killing the thing even worse than it already is
I'm also preparing to replace my digitizer. I came across a couple recent tear-down videos:
http://forum.xda-developers.com/showthread.php?t=961252
http://www.repairsuniverse.com/htc-tmobile-mytouch-4g-take-apart-repair-guide.html
Good luck!
Phew. Just replaced my digitizer using the latter video. Putting it back together was fairly straight-forward by just following the video backwards, though a 'put back together' video would be convenient.
A couple minor caveats:
They skipped showing some phillips screws holding the motherboard in place (near the end). I think there were two of them. They're fairly obvious if you know to look for them.
I attempted to reuse the existing adhesive by reheating and applying pressure. This sort of worked, but the digitizer seems a tad loose. I don't think it's going to fall off, but it'd probably be better to remove the old adhesive and apply some fresh adhesive. Anyone know where to get a suitable adhesive?
Taking apart the MyTouch 4G is not that hard
I bought a used MyTouch 4G in pieces on Craigslist for $ 45 that had a broken digitizer (about $ 20 on eBay with free shipping) and LCD (about $ 40 on eBay with free shipping) and the Audio & Volume Button Flex Cable (about $ 38 on eBay with free shipping) was also defective (the power button cable was ripped which can happen very easily if you take the phone apart and if you are not 100% careful when you pry the power button cable out). I ordered all the replacement parts on eBay from US sellers.
This particular phone had the "bad", washed out screen and was manufactured in Taiwan. When I ordered the replacement LCD and digitizer, I was hoping to get the "good", bright and superior screen but that didn't happen. So for the ones out there who are hoping to improve the screen by replacing the LCD and/or digitizer, it's a 50/50 shot.
I also ran into the problem with the adhesive and found a roll of 3M 2mm double sided tape for $ 10 with free shipping on eBay. The phone is working great and looks like nothing ever happened now after I put it all back together. And even though I had to pay for a lot of replacement parts, it was still a lot cheaper than buying a new one from T-Mobile or a used one on Craigslist or eBay
There are also a lot of MyTouch 4G disassembly videos on youtube. I'm a gal and if I can do it, you can too !!
Hi guys, I've owned an Xperia Play since July 2011, since then I've had some 'Battery Cover' issues. First, let's start off by talking about the battery cover itself, well actually there's not much to say. If you have an Xperia Play you already know the battery cover is very cheap, it's a large rectangular piece of plastic that covers the entire back on the phone, it's a pain to get it off and on at times. So not only it is cheaply made, it also has the tendency to start 'squeaking' or 'creaking' after a while. This simple issue can be fixed my ordering a new back piece to replace the old one, but note, if you swap batteries, swap SIM cards, swap SD cards, or anything that involves taking the battery cover off, it WILL, at some point in time, get worn out and slightly bent out of place. There's no escaping this problem due to it's design. In the past I've ordered about 3 Black battery cover replacements, and each one of them, after sometime, became creaky. Now maybe I'm just being picky but I REALLY hate picking up my phone and hearing that *squeaky* sound. It annoys the piss out of me. So I've came up with a way to prevent / fix this. What I'm about to guide you through is EXTREMELY simple and shouldn't cost you more than $2... ENJOY
SUPPLIES: Electrical Tape & Scissors
(1) Hold your phone to where the back is facing you, gently but firmly press all around until you've found your squeaky area. ( take a mental note of where this spot is )
(2) Remove the battery cover.
(3) Cut off a piece or two of electrical tape according to the size of the squeaky area, place the electrical tape on the inside of the battery cover where you took a mental note of.
(4) Put the battery cover back on! You're all done! No more squeaking!
It worked for me, it should definitely work for you! Try it out and post your results! Don't forget to *Thank* me!
(I've included a picture of what the results look like, lol I'm sure we all know what a piece of tape looks like on a piece of plastic but yeah here's one in case you don't!)
Thanks, no more squeaking!
I dont care about the squeaking that much, but still, u made my play better!
CyberScopes said:
Thanks, no more squeaking!
I dont care about the squeaking that much, but still, u made my play better!
Click to expand...
Click to collapse
Glad I could help! Sure beats spending $10-15 for a new back.
Yep. I used strong masking tape.
Sent From My Sony Xperia Play. Press the Thanks button for Fun.
I've replaced the battery lid a few times but I've never had the creaking problem. I wonder if it has something to do with the CDMA version not having the space for the SIM card.
Anyway, I do agree that they are poorly made. My first one developed cracks around the pry point and around the top even before I got a second battery. Obviously, battery swapping means I open it more often than most users, but I was EXTREMELY careful. Eventually I lost the corner next to the power button. On my replacement I made sure to never use the pry point without relieving pressure by pulling the corners too (usually unclipping them first). I also used a stick-on carbon-fiber protector from the day I installed it till the day I replaced it. It eventually formed a crack by the pry point too. Argh!
Hey,
Just making this post to bring to light a common manufacturing defect I've discovered in at least two Xperia Z3 D6653 phones around the wrist strap hole. Apparently it's not completely sealed, and will leak air and water. As a hacky solution I've taped over the hole with electric tape, and that seals the device. I assume it's present in many more phones if the same problem showed up in mine. Just wanted to get the info out there before people start submerging their new phones.
I've made a video to demonstrate the issue:
(remove the spaces in the link. I'm having to obfuscate because I don't have the requisite post count)
htt
p://ww
w.youtube.co
m/
watch?v=6VpuMfpxCrQ
Wow. I can get the same thing to happen when I press against the lanyard hole vs not. However, before finding out about this, I previously dunked this phone in water with a video playing for about a minute and it continued to work fine. Was it only a matter of time before water would get it and make my phone fail? I'm not sure. But there I can't think of a good reason why the pressure will increase and stay high with the lanyard hole closed vs open and the pressure equalizes. I have the D6616.
lvlonkey said:
Wow. I can get the same thing to happen when I press against the lanyard hole vs not. However, before finding out about this, I previously dunked this phone in water with a video playing for about a minute and it continued to work fine. Was it only a matter of time before water would get it and make my phone fail? I'm not sure. But there I can't think of a good reason why the pressure will increase and stay high with the lanyard hole closed vs open and the pressure equalizes. I have the D6616.
Click to expand...
Click to collapse
I previously used the first phone underwater very briefly (about 30-60 seconds), and it seemed just fine. Though I tried it later for about 5 straight minutes and it started getting very hot in the lower left hand corner and it made a buzzing sound from that same area around the hole. It also wasn't very deep at all, only about 3-4 inches of water.
Fixed the video link for you: http://www.youtube.com/watch?v=6VpuMfpxCrQ
Manufacturing defect. The Z3 is full of it! :/
Attached is mine with an uneven flap.
hanime said:
Fixed the video link for you: http://www.youtube.com/watch?v=6VpuMfpxCrQ
Manufacturing defect. The Z3 is full of it! :/
Attached is mine with an uneven flap.
Click to expand...
Click to collapse
My 3rd one had that lol, 4th one so far seems aesthetically good.
abhinav.tella said:
My 3rd one had that lol, 4th one so far seems aesthetically good.
Click to expand...
Click to collapse
I'm trying to get another exchange from the ebay seller. Here goes nothing. Sorry for the off-topic.
Mines goes from 1007 to 1116 and straight back down to 1007. Should I be worried?
Sent from my D6603 using XDA Free mobile app
I was the one on your YT vid that suggested using black RTV silicone, in place of electrical tape, to seal up this apparent hole. RTV silicone is rubbery when dry and yet can easily be removed when needed and will not damage the phone. As well, it is black so it will match the phones body to some degree. If needed, get a toothpick and pop out what you filled in. If not, leave it forever and seal up the hole.
That's a good idea but I'm annoyed by the fact that we have to resort to these fixes for something that shouldn't be a problem in the first place.
How are you 100% positive that just because it leaks air, it is not waterproof. I fish a lot and wear breathable wader that do not let water in but it is not air tight since it lets water vapor/air out. Water molecule is relatively large compare to air molecule.
Someone should make a tiny rubber plug, I'd buy one just to ease my paranoid side.
aquaholik (interesting SN to point this out) made a good comment as well, things can be watertight but not necessarily airtight and this could be by design to let the internals breathe
Agree with aquaholik. And the most important part, shouldn't the barometer sensor have access to air? How else can it measure the pressure of air?
lvlonkey said:
That's a good idea but I'm annoyed by the fact that we have to resort to these fixes for something that shouldn't be a problem in the first place.
Click to expand...
Click to collapse
Agreed 100%. But I will take my idea over a piece of tape any day
se1000 said:
Someone should make a tiny rubber plug, I'd buy one just to ease my paranoid side.
Click to expand...
Click to collapse
use my RTV Silicone idea and you will get just that. It will form the area and make an impression and IF you opt to take it out, you would have a "plug" of sorts.
My phone has this behaviour as well. I already had it in water briefly.
This might be a seal/mebrane to account for heavy pressure changes.
Bäcker said:
My phone has this behaviour as well. I already had it in water briefly.
This might be a seal/mebrane to account for heavy pressure changes.
Click to expand...
Click to collapse
I'm copying my response to a reddit post I made about the video...
...the first (now non-functional phone) only lasted about 5 minutes in about 3-4 inches of water. When I pulled it out of the water, it was buzzing and really hot in the lower left corner, which is exactly where the lanyard hole is.
This is very strong evidence that water got in through that hole, especially since the rest of the phone is so well sealed. Plus lasting only 5 minutes at that depth is clearly below the rated performance of 1.5 meters for 30 minutes.
When I got the first phone, I tested the waterproofing of the device by putting it in a dish of water for about a minute, and it seemed just fine after coming out. So I assumed it was sealed, but it simply took much longer for water to enter.
Given my experience with the first phone, I'd rather play it safe and just tape over the hole than risk damaging yet another device in conditions that are well within spec.
Yeah, I totally understand where you are coming from. But if there was indeed a membrane/valve to counter dramatic pressure changes, then closing this pathway could lead to new problems.
Bäcker said:
Yeah, I totally understand where you are coming from. But if there was indeed a membrane/valve to counter dramatic pressure changes, then closing this pathway could lead to new problems.
Click to expand...
Click to collapse
That's true if it's by design. Which it may still be.
However, I'm going to just run 100% with it plugged and see if anything happens. I really can't afford to lose yet another phone in just a few weeks, and If I do get any negative side effects, I'll be sure to report back.
I'm so paranoid. After reading everywhere complains about the questionable waterproof of the Z3, I decided to give it a ride and check out if it really survives, as I still have the return policy and I was really scared but I put it in water, not to deep, took a little bucket and filled it with about 10-15 cm water and waited for about a minute. As I expected it survived well and I didn't see any abnormalities. Then I dried it up using a microfiber towel and everything works fine. I'll see the next days if I find something strange but everything seems fine. Speakers and microphone work well.
Send your other one through sony repair.
They should cover it as long as the indicators arent red.
They repaired my original Z which displayed water damage, but because the indicators didnt turn, fixed it.
Its clearly a manufacture defect if it is the lanyard hole being open which is causing the problem.
killa78 said:
Send your other one through sony repair.
They should cover it as long as the indicators arent red.
They repaired my original Z which displayed water damage, but because the indicators didnt turn, fixed it.
Its clearly a manufacture defect if it is the lanyard hole being open which is causing the problem.
Click to expand...
Click to collapse
they should cover it even if the indicators are red, they market it as a water resistant device.