Related
after my phone rebooted once the update was complete, it wont get passed the "at&T World Phone" white screen... SOMEONE PLEASE HELP ME!!!! i was using a stock at&t pure with the stock rom. i can not upgrade hardspl or ANYTHING any suggestions on how to get my phone to boot? hard-reset went through with no signs of failure but it still will not boot up after that finishes... sorry if its something im overlQQKing, but i just cant figure it out. n yes i have researched although obviously not enough at this point. Thanks to anyone who can help in advance. forgive my stupidity!!!
......
noone?????
The HTC Pure updates hosed my phone too, I had already applied hard-spl to my Pure and i've flashed it with dozens of roms. Since I was currently using one of the "Stock" AT&T roms posted on XDA I figured I could apply the updates. Unfortunately after applying the update my phone froze at the boot loader. I was forced to flash my rom using the memory card method and then restore a backup.
you could try putting the phone in SSPL mode manually, (reset button+volume down), the run hard-spl hard-spl in manual mode.
you can then flash your rom using the memory card method. (FAT32 formated memory card, rom file renamed to topaz.nbh copied to root of flash card, reset button+volume down to enter SSPL, power button to confirm flash).
All this assumes you've already tried to hard reset your Pure (reset button+vol up+vol down)
Thanks for the reply! Unfortunatly, i tried the manual method and after it hanging at 0% for about 5 minutes, i keep getting error [262] update error.. (communications error) is this becuase i can not sync with mobile device center (win7)? I really dont want to just have to toss the phone! I have had an at&t tilt, at&t fuze, and now the at&t pure, and this is the only phone i have had this problem with for some reason...
Try Unplugging Your Pure From the computer Take Out the Battery Put the Battery Back in Mean While Restart your computer and Press Power And Volume Down At the Same time on your Pure If its on the colored screen your good,..Make sure your system is online and your not downloading anything and plug in your Pure to the computer it give it about 2 minutes to download the HTC USB driver then once its done your phone will say USB on the bottom of the Red Green Blue And White four color screen Then open up one of your ROM's and Flash it,....Do You Have Windows Mobile Device Center Installed?
If Not here is the Link
http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
If you do already you need to uninstall the Driver update for windows mobile media center then install it again .
i can get the bootloader screen just fine! i just can not get hardspl to flash onto it. it sits at 0% every time. the phone will not boot so i can NOT get into mobile device center. The tri-colored screen comes up with no problem and it says USB on the bottom, so the drivers are already installed. I even tried hard-reset and still no luck
There was an additional cab file I needed to install to HSPL the Pure
"enablerapinew.cab"
basically the machine just would fail to load the HSPL without it
but it still functioned afterwards, does yours?
Do a search on XDA find and DL the cab (or I could attach a zipped copy)
If you can still access the device,
just copy enablerapinew.cab to any temp dir on the device
the execute it through fileexplorer
then go back to installing the HSPL (mine then worked fine)
If you haven't already, You should go to
http://forum.xda-developers.com/showthread.php?t=520312
you'll find troubleshooting info and a link to the extra cab there
If you really are bricked at this point , it sounds like nothing has actually
been changed on your device yet? its just frozen should be still under warrentee? Unless anyone else has a better suggestion you should be
able to return it for exchange to ATT
Good Luck
KJL
It sounds like Windows is not properly recognizing your device when it is plugged into the USB port while in SSPL mode.
Have you tried different ports?
Is there another computer you can use?
another thought about returning under warranty
on the boot page of the stock Pure it indicates HSPL 1.83.000
After you update the HSPL it will say HSPL "1.83.Olinex"
this normally an indication of a successful update,
but it will probably void your warranty if they just look at the boot screen
This is true for all Pure (and Tmobile Compact V) Rom upgrades
The Stock Pure came with 6.5 and therefore the 1.83.00 HSPL
The Diamond2s did not, so their solution which reverts to 1.63 <?>
will not correctly revert to 1.83.00 on the Pure.
No way to correct this yet as far as I know,?
All the "reverts" are geared toward the Diamond2s, not the Pure.
But If your boot screen indicates 1.83.00 before it freezes
I'm fairly sure its still entitled to a warranty repair/replace
How could they tell the cause of the failure
was a reburn as opposed to natural causes?
Good Luck
KJL
When you put the phone into a manual bootloader mode... Mobile Device Center becomes obsolete.
HardSPL is only needed for unofficial roms. Forget HardSPL for the time being. The goal here is to get your phone operational. Just download the official HTC WM6.5 WWE rom and flash that. Put phone in manual bootloader mode and run the Rom installer.
As long as your phone is in bootloader mode and says "USB"... then your set to go.
Another solution is to try another PC. You'd be surprised how often that will resolve your issues. Perhaps find an XP machine and install Activesync (so it loads the bootloader USB drivers). I had to do that on several occasions when my main PC refused to flash my mobile device.
I did both of the updates htc has for the pure. Both worked fine. I am on the origianal rom. It does reboot your phone and stays on the white screen for a min then it loads the update and the phone starts.
The offical ROM comes back with a wrong vender ID error I guess cause its a "pure" and not the HTC branded "topaz"... NOW what should i do??? Seems like i NEED hardspl so i can flash any ROM, as from what i researched, there IS NO AT&T Pure rom that has been released. I still cant figure out why a hard-reset will not work though.... This is REALLY starting to get me angry!!!
Just for reference, the Pure's ID is TOPA210 32M
SPL-1.83.0000
The official hotfixes worked fine for me as well. Did you apply the hotfixes on the original ROM that came with your Pure?
Also, does the official HTC Touch Diamond 2 ROM work for you? If so, the hotfixes for the Pure are irrelevant, as are any future updates released for the Pure. You should look for updates for the Touch Diamond 2 on the Worldwide HTC site.
If you needed to do a warranty claim, the closest you can get to returning your phone to stock/shipped form is to use the ROM dump using HardSPL and hope they don't notice that the SPL is different. Currently, there's no way to return the Pure back to completely official software.
A hard reset simply wipes everything off and restores everything back to what is contained in just the ROM you currently have on it. If you've flashed your phone at all, you've already wiped out the original ROM that came with it.
It is still the STOCK ROM. I have never flashed it yet.. The topaz rom will not flash due to a vender ID error. The spl is still stock also... i think thats is why i am having this problem. I bought the phone off craigslist so returning it to AT&T is NOT an option either way. My only solution is to find a fix. (or trash it) I really appreciate all of your suggestions and input so far. You guys are by far the best board around! I am a LONG time follower, but a few-time poster. Obviously i have little to contribute to the board.
Can I trouble you to dig up a few version numbers? It'd help evaluate your situation so we can see which options are best for your case.
ROM version? You can find this in Device Information. Start --> Settings --> System --> Device Information
Bootloader version? Do a soft reset while holding down the volume down button on the side until a screen with red, green, blue, and white, ordered top to bottom, shows up. It should be the second line starting with "SPL-..."
The ROM is the STOCK AT&T ROM (again...) I CAN NOT go to start;.... because if you noticed in the first post, the phone will not boot past the white "AT&T WorldPhone" screen... the spl is stock also incase you missed that part. (1.33.0000) I have never flashed the divice. EVERYTHING IS HOW AT&T SELLS THE PURE OUT OF THE BOX! NO MODS. NO FLASHED ROMS. NO HardSPL... NOTHING! STOCK!!! (for those overlooking the details in my previous posts) I have no doubt you guys (n hopefully a few girls ) will help me fix my issue. I'm just REALLY anxious for it to happen sooner than later!
Have you tried downloading the official rom here on xda and renaming it to TOPAIMG.nbh and update using the sd card method?
Here is the thread:
http://forum.xda-developers.com/showthread.php?t=600339
The download is in post #1
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
jromeo350 said:
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
Click to expand...
Click to collapse
You can flash hard SPL the same way by renaming the .nbh file to
TOPAIMG.nbh
jromeo350 said:
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
Click to expand...
Click to collapse
Actually that is supposed to be an officially signed rom. If that is true it will work with the stock spl. It will either work or it won't. Also, as stated in the response after yours, you can apply the hardspl via SD as well.
Hey,
I'm getting my phone replace because my phone is unresponsive. I have a question to those who got a replace phone. Did you send broken phone with custom ROM on it or did you put it at stock ROM? Also does anyone know if I can install stock ROM via bootloader. My phone can load into bootloader and run fastboot commands etc... but can not boot into recovery so I was wondering if there is way to flash stock rom using bootloader and usb.
Thanks for everyone's help!
Even if you get the original rom back on there, your bootloader is unlocked, so your warranty is void. There's a chance they'll help you out anyway, but I don't think putting the stock rom back on will help.
Hey guys,
I tried to search in de app but couldn't find it so here is my situation.. yesterday i let my Desire hd Dell on the ground is does work but i got a burst in the screen.. im going back to the store to send it for repair but 2 things..
1. I need to get the stock splash back on it
2. I need to get the phone back to stock..
Please can someone help so i can get phone repaired??
Many thanks already!
Sent from my HTC Desire HD using XDA Premium App
No problem.
You can find the stock splash screen here: http://forum.xda-developers.com/showthread.php?p=15430340&highlight=stock#post15430340
Uncompress that and put the .img file in the same folder as your fastboot file (in the Android SDK, it used to be in the Tools folder but nowadays they put it in the Platform-Tools folder), then open a CMD window, (Make sure the file is called splash1.img) and type:
fastboot flash splash1 splash1.img
That will restore the stock splash screen.
To restore the software you have to:
1: Find a 1.32.405.6 RUU that matches the original state of your phone.
2: Flash that RUU
3: Use Visionary R14 to Temproot and then Permroot
4: The Jkoljo's Easy Radio Tool to change the CID back to stock (If you phone was unbranded it will be HTC__001)
5: Also use that tool to restore S-On
6: Reflash the RUU
7: Upgrade to the latest software through the usual software updates.
Hope that helps.
that helps, thx.
Restoring Desire to factory
hi,
i've checked everywhere and i cant find it. i need to restore my desire to how i originally got it, and silly me i did not back up my rom. Can some one help?
Thank you
+ i cant find anywhere a 1.32.405.6 RUU
Stock Roms HERE
ROM 1.32.707.5 CL277010 w/ 12.28b.60.140eU_26.03.02.26M
sorry for sort of hijacking this threat, but it is related.
I got a DHD (SE Asia I believe) with ROM 1.32.707.5 CL277010 with baseband 12.28b.60.140eU_26.03.02.26M. I rooted it and want to go back (only because I can not apply the System upgrade, which is available), can not find any SE Asia ROM though.
Q.: Can I (safely) just use any WWE RUU or does it need to be the SE Asia ROM?
Hope somebody knows...
If its not for warranty purposes then a world wide ROM is fine. If it is for warranty purposes you would need to get it as close as you could to the original state.
However can I ask why you want to unroot? The ROM's on XDA are much better than the ones HTC give us.
By the way, please start a new thread next time. It keeps things organised
After seeing this issue quite a few times this past week I thought I make a tutorial on how to possibly fix this. If any of you see any errors or any way to improve this guide please let me know and ill include it and or adjust accordingly
Note-Make sure you have plenty of battery. You don’t want your phone dying in the middle of flashing a PD98IMG
If you are stuck in Hboot and have S-On go straight to flashing Stock Rom section or Alternate method at the end
Do not rename or unzip-Leave as is
Recovery: http://min.us/mbaD8QTK4A
WWE Stock Rom (Sense 3.0): http://min.us/mIc6tkSGg
NOTE- The Stock Rom is for a Desire DHD. If you have an Inspire 4g or Telus DHD do not use the file. Use one of these instead
Inspire 4g pre-rooted Stock Rom: http://db.tt/DCU3oW39 (only use if you have S-off)
Inspire 4g stock Rom: http://min.us/mblzL6b6vL
Telus DHD Stock Rom: http://min.us/mTqXM8fTY
Reinstalling Recovery
If you have Eng S-Off and feel comfortable with adb you can flash a recovery that way. Go to Reinstalling Recovery using adb
For whatever reason you have wiped your custom recovery (My guess is you did a factory reset, thus erasing it). Personally i would try this first as one can go straight to a custom rom. If you don't want a custom rom feel free to go to the flashing stock rom section.
1)Back up anything you don’t want deleted from your sd card
2)Plug in sd card into computer through an adapter of some kind or another phone
3)Reformat the Sd Card to Fat32 – Do a full reformat not a quick
4)Once reformat is complete place the file downloaded from the first link on the sd card
5)Eject the sd card from computer and insert into phone
6)Power off phone by pulling the battery
7)Reinsert the battery
8)Boot into bootloader by pressing volume down and power button
9)It will scan for the file press volume up to accept update
10)It will ask you to reboot- but it will still be stuck which is normal
11)If everything is going to plan you now have access to recovery. So now we need to flash a rom. Skip down to the flashing rom section if you don’t know how to. If flashing the recovery didn't work continue to the next section
Reinstalling Recovery With No Card Reader
Note: Eng S-OFF is not needed for this method
1) Download recovery above and place it in your fastboot directory
2) Boot into Hboot
3) Connect your phone to your PC
4) Select fastboot
5) Open up command prompt and CD to your Fastboot directory
6) Run the command fastboot erase cache
7) After the OK run fastboot oem rebootRUU
8) You'll see a new screen with HTC logo and a progress bar. here you need to run fastboot flash zip PD98IMG.zip
9) Once it completes (should say ok,finished, or complete) run fastboot reboot bootloader
10) Go into Recovery and flash a rom
Reinstalling Recovery Using ADB and Fastboot
Note: you need to have Eng s-off with this method.
You can use the recovery img that is found above or one of your choosing(newer cwr or 4ext recovery)
adb reboot bootloader
fastboot flash recovery recovery.img
fastboot reboot
Flashing a Stock Rom
Note-If you are S-off I suggest flashing a pre-rooted stock rom, as there is no need to re-root.
1)If coming from previous section plug in sd card and delete old file then Jump to step 5
2)Back up anything you don’t want deleted from your sd card
3)Plug in sd card into computer through an adapter of some kind or another phone
4)Reformat the Sd Card to Fat32 – Do a full reformat not a quick
5)Once reformat is complete place the file downloaded from the second link(stock rom) on the sd card
6)Eject the sd card from computer and insert into phone
7)Power off phone by pulling the battery
8)Reinsert the battery
9)Boot into bootloader by pressing volume down and power button
10)It will scan for the file press volume up to accept update
11)If everything is going to plan you now should have a fully working phone
12)At this point you are un-rooted so if you want re-root I recommend using the ace hack kit. (unless you used a pre-rooted rom then no need to use hack kit)
NOTE- IF EITHER FLASHING THE STOCK ROM OR RECOVERY PD98 FILES HAS NOT WORKED REPEAT PROCEDURE WITH A DIFFERENT SD CARD
Flashing rom
1)So we were able to re-flash a custom recovery. Connect sd card to computer and delete the PD98img file
2)Download the rom of your choice and any super wipe zips if your rom needs it
3)Place file on sd card eject and reinsert onto phone
4)Boot in bootloader.( An alternate is using adb to boot into recovery)
5)This time it will scan and not find any files. After it scans scroll down and select recovery.
6)You should now be in CWR. Do a full wipe (wipe data, cache, and dalvik cache-found in advanced I think
a.If recommended by your rom uses a super wipe zip. Simply choose install from sd card in CWR and select the super wipe zip
7)Now flash the rom by selecting install from sd card and choosing rom
Alternate- Flashing of a RUU
This is for those that don’t have access to an adapter to place files with. This should work whether your S-on or S-Off
RUU’s: http://www.filefactory.com/f/efa28fefafc4af9c/
1)Download your RUU from above
2)Boot into Hboot
3)Connect your phone to your PC
4)Select fastboot
5)Run the RUU program
Credits to Gene Pool for the Recovery PD98 and pre-rooted RUU for us inspire users.
Thanks to Gizmoe for his link- helps avoid the renaming issues that crop up and idea for alternate RUU flashing,
Thanks to Football for the RUU.exe links
Thanks to Attn1 for the hack kit, all the devs for their awesome work, XDA members who are on here helping people out. I have learned so much just by reading
UPDATES
10/4/12-New method of flashing recovery added. No card reader needed for those that do not have engsoff or the modified hboot from the AAHK-learned this method from Glevitan
3/14/12--Updated links in OP
2/12/12-- Here are some mirrors for the PD98IMG files that were hosted on multiupload. Hopefully multiupload isnt down for good, so in the mean time i have them on depositfiles
Inspire 4g stock Rom: http://depositfiles.com/files/4ofstmcse
Telus DHD stock Rom: http://depositfiles.com/files/mec1ycc7k
WWE DHD Stock Rom (Sense 3.0) : http://depositfiles.com/files/nmxfys544
CWR Recovery-make sure to rename
http://hoxnet.com/droid/PD98IMG_cwm5026_recovery.zip
1/26/12- note for all, because of recent events regarding megaupload, those links do not work. Simply use and alternate
1/7/12- changed link to ruu's. Old link no longer had dhd version only NAM versions. Thanks to football for.the link
12/23/11-included note of flashing prerooted PD98IMG as a preferred preference so one doesnt have to reroot-Thanks fernandezhjr
I'm hoping to add a link to a preroot dhd pd98 to the guide. If one you know of a link I'll gladly add it
Reworded use of RUU to stock rom when referencing the PD98 file as to avoid confusion of RUU.exe that is run from a pc-Thanks preacher
Edited to cover up my newbish mistake. Maatsby knows why lol
haha, glad I could help. we all make newbish mistakes now and then, especially past a reasonable hour
One doesn't have to unroot if they don't want to flash the recovery through hboot. One can place a rooted version of the stock rom on the SD card as a pd98img zip and boot into hboot. Once flashed, just go to the market and install rom manager and flash recovery from there. At this point, one is rooted stock and free to flash a custom rom at any time. This saves from the need to reroot the device. Of course this is provided one already has s-off when the problem hit.
Sent from my HTC Inspire 4G using Tapatalk
fernandezhjr said:
One doesn't have to unroot if they don't want to flash the recovery through hboot. One can place a rooted version of the stock rom on the SD card as a pd98img zip and boot into hboot. Once flashed, just go to the market and install rom manager and flash recovery from there. At this point, one is rooted stock and free to flash a custom rom at any time. This saves from the need to reroot the device. Of course this is provided one already has s-off when the problem hit.
Sent from my HTC Inspire 4G using Tapatalk
Click to expand...
Click to collapse
I did make in the note of guide, though it was in the last step. Ill add a note further up. I didn't suggest that way first as I dont have a link for a prerooted pd98 for dhd users. In the inspire section I did recommend the easier way as you suggested. Ill see if I can find a prerooted dhd pd98 and add it
marsdta said:
I did make in the note of guide, though it was in the last step. Ill add a note further up. I didn't suggest that way first as I dont have a link for a prerooted pd98 for dhd users. In the inspire section I did recommend the easier way as you suggested. Ill see if I can find a prerooted dhd pd98 and add it
Click to expand...
Click to collapse
When I made my post, I was lost and thought I was in the Inspire thread. Lol. I knew I had seen this over there last night, but it disappeared on me. What happened is a mod quickly stickied it and I hadn't clicked on the stickies tab earlier. I see where you suggested it now.
Sent from my HTC Inspire 4G using Tapatalk
thanks. u just save my phone.
Potential to stickie, a really clear and useful guide.
Sadly, didn't worked for me
This guide helped me alot! Worked perfecly and now i run a 4.0 android rom
Hey, you exactly explained what my problem is and obviously solved for some cases. But unfortunately, links don't work due to idiocratic SOPA. Hence please review the links so we can solve our problems. Thanks in advance.
q995 said:
Hey, you exactly explained what my problem is and obviously solved for some cases. But unfortunately, links don't work due to idiocratic SOPA. Hence please review the links so we can solve our problems. Thanks in advance.
Click to expand...
Click to collapse
All links work, just don't use the megaupload links
I've tried everything that has explained but unfortunately it didn't work out for me.
Thanks..Very helpful, for noobs like me..
do too MultiUpload being down lately I uploaded mirrors to the pd98imgs. Please see second post
I also uploaded two WWE version the RUU for those that want them. Hopefully faster downloads than that on the filefactory link
GB Sense 2.1 2.50.405
http://depositfiles.com/files/2wlrviqhg
GB Sense 3.0 3.12.405
http://depositfiles.com/files/gsi0uoeu4
Sorry For Being a Noob
Hi guys, my Desire HD was installing the update and i didnt think that it was doing anything so I pulled the battery, has not turned on since :/ although it is currently on charge and the orange light is on.
Any Ideas would be greatly appreciated,
Many thanks,
Sam
tmobile help please
Please can anybody download t mobile ota update ? i need to flash the update zip file to my t mobile dhd because i have installed tmobile ruu and my phone wont boot it is stuck in t mobile boot loop i have no root and my hboot says
ACE PVT SHIP S-OFF RL.
I have an unbranded dhd but i dont know if i can install tmobile ruu on to it to download the tmobile ota update myself.. i have done this with my htc bravo's
one was virgin and the other was unbranded i was able to s-off the unbranded bravo using revolutionay.io and install virgin ruu on it and downloaded the ota zip file but didnt install it and copied it to my virgin bravo and installed the update can i do this with dhd ace ?
if you have supercid on the unbranded you can do that, though i dont think the ota will get you out of the bootloop. When you installed the tmo RUU it does take about 15 min to do its thing. did you give it enough time?
You could reflashing the Tmo ruu, but since your soff i would personally use the WWE version
Sorry Guys looking for some extra help, I was flashing a radio on GB and something went wrong... I am running a custom rom and am rooted with ENG s-off.
when I start i get a black scree for about 10-15 minutes, then I get a white screen with HTC on it and it vibrates for a good 5 minutes, then it goes to a white HTC screen with quietly good (or something similar) and eventually the phone will start.
I had ext4 CWM installed on it originally but I do not get any recovery options either in HTC or CWM.
I've tried using the instructions here with adb a recovery image to no avail.
The phone is currently 2.3.5 with HTC sense it was Android Revolution HD 6.3.2 by mike 1986.
---------- Post added at 11:30 PM ---------- Previous post was at 10:41 PM ----------
Hunterdiver said:
Sorry Guys looking for some extra help, I was flashing a radio on GB and something went wrong... I am running a custom rom and am rooted with ENG s-off.
when I start i get a black scree for about 10-15 minutes, then I get a white screen with HTC on it and it vibrates for a good 5 minutes, then it goes to a white HTC screen with quietly good (or something similar) and eventually the phone will start.
I had ext4 CWM installed on it originally but I do not get any recovery options either in HTC or CWM.
I've tried using the instructions here with adb a recovery image to no avail.
The phone is currently 2.3.5 with HTC sense it was Android Revolution HD 6.3.2 by mike 1986.
Click to expand...
Click to collapse
Fixed it thanks ....
managed to solve the delay after booting by following these steps:
Q&A DHD Page 175 post 1749 lebsir
Hello! I have a Desire HD that is stuck at the Hboot, no recovery or anything.
I managed to flash some ROMs, either through Hboot or RUU but even then, the phone stays stuck at Hboot.
I tried many official ROMs and RUUs. The ones that can be flashed succesfully are the main zip from this thread (WWE Stock Rom) and the two Sense 3.0 WWE RUUs.
The update process seems to proceed fine, but at the end, when I reboot the device, it gives me 7 vibrations at the white HTC screen, then the screen goes black and stays stuck for ever (or at least for 2 hours).
I do not know much about the device, only that it had a custom rom and one day this happened.
If you have any suggestions or ideas, I'd be glad to hear. Even some generic (short) answers will do if you have any idea at all.
HTC service says that because of the custom software, the phone isn't anymore under warranty and they need to replace the motherboard.
Im wanting to return my rooted DHD to stock for warranty repair.
Ive downloaded RUU HTC WWE 1.72.405.3 but dont believe this will restore the stock splash screen.
Can anyone advise, if not can anyone upload original HTC SplashScreen so I can re-flash.
TIA
It will replace your bootsplash to the original. Remember flashing an ruu will not completely take you back to stock. You'll still have soff, supercid. Use the ace hack kit's return to stock option
Thanks...
I flashed RUU 1.32
Used s-off tool to s-on and stock cid.
Is there a way to confirm all is now stock unbranded as new?
I tried menu - settings - about phone
check for updates and it says i have latest version installed !!!
How can i confirm if DHD is restored to stock as surely i should get update notification when checking for update.
Edit: nvm i just tried again and it showed 1.32.405.6 is available as update.
I presume it wont show latest release, but in date order of release from current rom.
To check if everything went according to plan. Look in hboot to see if your back to son.
Also if you want to skip, flashing all the Ota's until your current, you could just flash a newer ruu.
All sorted, cheers.
I forgot about unchecking fastboot
All ready now for warranty repair at HTC.