Hi all,
In all of my previous Nokia phones (6600 and N90), there is a feature within the phone to disable sending MY phone number when I call someone. THus, the when I call, the receiver party will see "no number" or something like that.
However, I don't see this feature in the MDA. Is this possible with the MDA?
Start > Settings > Phone then the Services tab.
Select Caller ID and it will (should) open a screen asking if you want to provide Caller ID to Everyone or No one.
Chris
Sending your caller ID is generally a setting of your provider.
If you want to suppress your caller ID for the next call try the following:
#31#phonenumber
This works for all german provider, i'm not sure if this combination works globally.
hope this helps
I have some contacts saved in my contact list, but when that person calls. It showed up unknown caller. I tried to deleted that number and save it again. But it still shows unknown caller. Some other contacts are fine. Anyone had this problem and has a solution? Is there anything to do with restore? I did a restore recently.
don't know if it helps, but try to save the numbers with the country prefix in the contact.
for example in France here, I save them as +33654321 instead of 0654321, cause I had the same problem some time ago
This doesn't have anything to do with the Wizard - if the Wizard shows "unknown caller" it means that the caller's phone doesn't send the number (the caller can change that, depending on the SIM card - and the caller can also tell the telecom provider of his home phone whether he wants his number to be sent when calling!)...
No way to change that for you, sorry!
I have tried adding the prefix, but still doesnt work!
The number from the caller is not hidden, because the number is displayed, but not the name in the contact list.
for example:
Incoming call
'Unknown Caller'
0709XXXXXX
I have tried to delete and save the contact again, but still the same!!
Oh, so I misunderstood...
Sorry, but then I don't have any idea...
Not sure if this helps. I had the same experience with my other phone (not Pocket PC type), which shows unknown caller even I'm very sure I had his number on my phone, I deleted the number and put it back again, same problem. AND, after all the stuggle, I've finally noticed the problem, which is the fact that I had his name entered twiced (e.g. two contacts, different name with same number). The phone probably got it confused and refused to display a name.
I would suggest, that you remove your problematic contact, try dialing his number on the keypad, and see if the name appears (e.g. the other possible contact that has the same number). If not, then it is not this problem, I guess.
Was about to say, I got this problem, turned out to be a duplicate contact - the phone can't decide who it is, so displays nothing. Pfff.
Be nice if it displayed a list of possible contacts, but...
Delete any duplicate contacts and it should go away.
In my old Hermes (Cingular 8525), there is an option in the Phone Settings to hide my caller ID, so that when I call someone they will not see my number on their phone.
However, with my Mogul, I don't see that option. Does anyone know how can I do this?
I miss this feature on the mogul too. But you can type *67 and the number for example the number is 18001234567 type *6718001234567
P.S. if you find a patch to do this from a menu I would love to hear about it.
Thanks for the info. But that means I can't use my "Phonebook" to dial, as I have to manually enter *67 and then the number.
Maybe some of our resident hacker can figure it out?
Do you just want to permanently hide your number from everyone you call? If so, you should be able to ask your carrier to add a "No Caller Id" code to your account...
you could edit the phonebook entry or make an aditional one that is blocked and call it their "other" number or fax or something
Hi all,
Thanks for the suggestions. I don't want to permanently block my caller ID, only for select number. I prefer to be able to change the caller ID feature on the fly without editing the phonebook, but I guess I'll have to do so until Sprint implement this feature.
Hi
I'm with Bell Canada and we have a option on their web to block caller ID. I selected this option and in my contacts I added *83 to the number I want to unblock my ID. So if I dial a new number I know that my block caller ID is on.
Hi there, I'm wondering if anyone else might be having a similar problem with 'caller [or texter] ID'.
Most networks, as I understand it, use the international dialing code when sending out texts and calls, meaning this is usually the incoming number when you recieve a text or call.
I've obviously got people programmed into my contacts who text me but when they do, I don't get their name, I get their number - with the dialling code eg. +447750500500. When I tap to go into the threaded mode, I'll get all previous contact with this person but with them identified only as the number. However if I head to the People tab, then again to see the messages I've sent/recieved with that person, I get the same messages only under the banner of their name and not the number.
I believe calls work fine with the code programmed in on their contact profile.
Anyone know why this is being caused?
I have the same problem. Both calls and text messages.
I don't think it matters if the international code is there or not.
Really frustrating not knowing who calls.
I've had this problem first time the device was initialized (right after opening the box). It might be caused by the fact I didn't have any SIM in it at that time, I'm not sure.
After a hard reset with a SIM inserted, everything started working as it's supposed to.
Hmm, I've changed the SIM, but I can't remember if it worked wih the first SIM card.
But a hard reset deletes everything, right?
There are a few things you have to be sure of:
Do not have double contacts, if you have a number (with and without operator/country prefix) twice in your list it will not show any name.
I don't know if this applies if you have a contact on your phone memory and on your sim card. I am sure it does have this problem if you have two contacts with the same number on the memory phone.
For some reason this is logic: On an incoming call, the phones checks it's phonebook and retrieves two numbers and then it does not know what to display, is it contact one, or two?
I hope this helps you out. I did not experience any problems (yet).
AndrewCZ said:
I've had this problem first time the device was initialized (right after opening the box). It might be caused by the fact I didn't have any SIM in it at that time, I'm not sure.
After a hard reset with a SIM inserted, everything started working as it's supposed to.
Click to expand...
Click to collapse
Try this....
1. Edit one "test number" in your contacts and remove international codes.
Just put that "test" tel number. without int. codes... And make sure that number is not stored nder another contact. (No duplicates.)
2. Then dial from that number and see if that tel# is identified. If you have just "0xx-123456" then go to #3.
3. Go to registry and change of the Caller ID match rule. (Minus one digit.)
Example: Caller ID rule:8 (Change from 8 to 7 or 6 to 5 .. trailing digits for Call ID match. )
* HKCU\Control Panel\Phone\CalIidMatch value:7
4. Restart and test again...
5. If its OK, than test with SMS.
6. If its OK again , put back your international codes and test again.
7. If not go to no.3
Hope this helps.
KraFT
samluke said:
Hi there, I'm wondering if anyone else might be having a similar problem with 'caller [or texter] ID'.
Most networks, as I understand it, use the international dialing code when sending out texts and calls, meaning this is usually the incoming number when you recieve a text or call.
I've obviously got people programmed into my contacts who text me but when they do, I don't get their name, I get their number - with the dialling code eg. +447750500500. When I tap to go into the threaded mode, I'll get all previous contact with this person but with them identified only as the number. However if I head to the People tab, then again to see the messages I've sent/recieved with that person, I get the same messages only under the banner of their name and not the number.
I believe calls work fine with the code programmed in on their contact profile.
Anyone know why this is being caused?
Click to expand...
Click to collapse
Hi guys!! i had this problem too but i have fix the problem. what i do:
!) i store all my contacts in my sim card and delete the contacts in the phone.
2)do a hard reset
3)upon doing the hard reset, the phone will prompt you on importing sim contacts and finding your service provider. select both and and press ok
4)now try to call from your house to your phone to do a check.
5)my problem was solved after this
hope it helps!
KraFT_mk said:
Try this....
1. Edit one "test number" in your contacts and remove international codes.
Just put that "test" tel number. without int. codes... And make sure that number is not stored nder another contact. (No duplicates.)
2. Then dial from that number and see if that tel# is identified. If you have just "0xx-123456" then go to #3.
3. Go to registry and change of the Caller ID match rule. (Minus one digit.)
Example: Caller ID rule:8 (Change from 8 to 7 or 6 to 5 .. trailing digits for Call ID match. )
* HKCU\Control Panel\Phone\CalIidMatch value:7
4. Restart and test again...
5. If its OK, than test with SMS.
6. If its OK again , put back your international codes and test again.
7. If not go to no.3
Hope this helps.
KraFT
Click to expand...
Click to collapse
What was happening to me before the reset was a bit different - the phone wasn't able to match anything at all - even a number called from the phonebook and stored in "recent calls" in EXACTLY the same way it's in contact, didn't match to the contact when redialed.
I think that something required for Caller ID to work gets done when the phone is first initialized, and that this step requires full access to the phone module (which the phone doesn't have without a SIM inserted and a proper PIN entered).
hi,
i encountered also that worry,
i set the HKCU\Control Panel\Phone\CalIidMatch value:9
my mobile phone number to test was stored as "06xxyyzzww"
and when i phone my diamond2 from that number
the caller id is recognized
(with showing as +336wwxxyyzz)
i tested from my home phone stored in contacts as 04wwxxyyzz
i rang my topaz its was identfied as my home,
(with showing as +334wwxxyyzz)
i am in france, + is for 00 ,our phone numbers are 10 digits long
(mobiles and "home") ,
to be joined from abroad, you have to dial +33+phone number WITHOUT the first digit "0")
so the "9" value i put in the registry
if it could help you
regards
Hi,
just stumbled over the same problem.
The old phone (HTC P330) resolved numbers from my used format 01234-56789.
Since my contacts are a mess, I have 01234-12345, +49-123456-456, +49 (0123)-456 and so on, it would be a great pain in my ass to switch every contact to +49123-456 (which the new phone resolved).
I compared the Registry-Entry from the P3300 with the TD2 and voila: TD2 was 12, P3300 had the value 8.
I changed the TD2 to value 8, reboot and now I'm happy again, the phone is getting used to my contact list
Regards
Heiko
Hi,
I'm experiencing the exactly same problem, that incomming calls or messages isn't shown by name, but only by number.
I'm all new to Windows mobile, but I tried downloading a regeditor, and experimented with different values in the CallIdMatch string. However, no succes.
I live in Denmark, where numbers look like +4512345678, where +45 is the international code. Can someone please tell me, what should be the correct value? The original values was 8.
I have further found that some contacts are recognized. What the difference is between the groups, are however unclear!
Caller ID problem, my solution
I had the same problem. But after a hard reset it seems to work just fine now. Remember to backup your downloaded programs etc before doing this.
Tyven said:
Hi,
I'm experiencing the exactly same problem, that incomming calls or messages isn't shown by name, but only by number.
I'm all new to Windows mobile, but I tried downloading a regeditor, and experimented with different values in the CallIdMatch string. However, no succes.
I live in Denmark, where numbers look like +4512345678, where +45 is the international code. Can someone please tell me, what should be the correct value? The original values was 8.
I have further found that some contacts are recognized. What the difference is between the groups, are however unclear!
Click to expand...
Click to collapse
Hi,
"8" should be the good figure for you, as in France
we have phone numbers +33987654321
and "9" is the good value for me, in:
HKCU\Control Panel\Phone\CalIidMatch value:
Edit: i remove previous "edit"
in fact all my contacts had been erased" so it was normal to have no caller ID?
ps: is your carrier sendind all the figures when you're receiving calls, i mean +4512345678
so perhaps you're encountering a bug .
you should try to backup your device, with a soft like spritebackup(special price for htc owners on their webpage) and experiment an hardreset
and restore
regards
Hi ,
did you ever try to change the following:
RegistryEdit and Decreasing the CallIDMatch from 12 to 7 solved my Issue
See below
HKEY_CURRENT_USER\ControlPanel\Phone" name="CallIDMatch"
Greetings from Slovenia
Hello,
that is my first post so please do not be very critical to my english level and PPC skills .
now this is an old thread but for BULGARIA the correct registry value is "9". Here the mobil numbers are as follows "08xx 123456" (9 digits without the ZERO at the very beginning). that is why the usefull number is that (default for my TD2 was 8). Now after this fix the phone can correctly identify which number i want to dial when i am inserting it by digits, instead of selecting the exact person. i do not know am i explaining correctly but i will try to put some more detail on that. When i want to dial some particular number (for example "08xx 123456") the phone select me the correct contact no matter how i put this contact in memory. with "+3598xx 123456" or only with "08xx 123456". before that intervention the phone identifies me the correct contact only if i type the digits, exactly the same way that i have added it to the memory. So i think that this registry key does not have a universal resolution. the resolution depends on how many digits is using tha particular mobile operator.
i hope that will be helpful for someone who is happy to own an HTC and is happy with it ... like Me
Hi All, I have a connection with H2O wireless in USA. I have this weird problem with my S7 Edge G935FD where whenever I dial an International number, I get a message on screen that says "Number changed by sim" and then the number changes to an US number. This only happens when I dial an International number.
I tried the sim on a Note 2 where it's working fine and the number doesn't get changed. So I'm pretty sure it's something with the phone.
Can someone please help me resolve this issue because whatever International number I dial, I'm finally getting the US number in my call logs and it's impossible to know which number I dialed.
s22.postimg.org/cyy4gdktd/20161020_060500.png
s16.postimg.org/qdesc2eg5/Screenshot_20161020_060303.png
Bumping up. Any help guys?
Bump
Bump.
look if you have some sort of SIM management app. If not look under networks and advanced dialing options. You need to disable the automatic code. I think it's set to something and that's what would change the numbers.
error666 said:
look if you have some sort of SIM management app. If not look under networks and advanced dialing options. You need to disable the automatic code. I think it's set to something and that's what would change the numbers.
Click to expand...
Click to collapse
I don't see any option where I could disable the automatic code. Looked everywhere in the phone. I don't have advanced dialing options either. I just factory reset my phone and still the same problem. Any help please?
I ran into the same problem and found that if the phone number is listed with a + in front of the area code, i.e. +4051112222, it will be changed by the sim.
To solve this, dial a 1 follow by the area code & number.