Related
Its been inspired by Sudeep Duhoon Thread , Thank him if possible . Except the rooting part everything is preety much same as Sudeep Duhoon did.
I just found out you could 7.2.3 much easily Root the device rather than editing scripts and all of the stuff which i didn't get from his thread.[No offense sir]
Downloads :
1. Minimal Adb Tool
2. MiFlash_2016.03.30.exe
3. Fastboot 7.2.3 Rom
4. Unlocked EMMC or check the attachment.
5. 7.2.3 PATCHED BOOT IMAGE
Unlocking Bootloader :
1 . Connect your Phone to Computer in USB DEBUG and OEM UNLOCK mode to the computer. [Both of these settings are turned on from developer option.]
2. In ADB check if your device is successfully connected using "adb devices" command .
3. NOW , Reboot the phone into EDL mode using this command "adb reboot edl" .
4. Now make sure you're device is connected in "Qualccomm HS-USB QLoader 9008" , if yes continue .
If the device is connected in "Qualcomm HS-USB Diagnostics 900E" Start it from step 1 again.
5. DOWNLOAD 7.2.3 fastboot Rom . Extract the rom.
Download, Extract unlocked_emmc_appsboot.mbn. Rename it to "emmc_appsboot.mbn" And move it inside the extracted ROM FOLDER.
6. Now Start the MI Flash Tool and Browse to the Location Where you have Extracted the Fastboot ROM
7. Go to Advanced and Select:
Flash Programmer, Raw XML File and Patch XML File
from the Fastboot ROM\Images folder.
8. Close the window and click on refresh , Your device with certain COM# will appear. Just click on Flash.
Wait until its successful .
9. Once it is successful , Hard Boot your phone to fastboot using POWER DOWN + POWER ON buttons on your phone.
10. Now in command prompt type "fastboot oem device-info" , you'll see the DEVICE UNLOCKED : FALSE
11. Now Enter the following command "fastboot oem unlock-go" . Your device must be unlocked , to confirm enter the previous[step 9] command again.
YOUR BOOTLOADER IS UNLOCKED NOW
FLASHING TWRP :
1. Move the twrp image in minimal adb folder. Rename the twrp image to twrp.img
2. Enter the command "fastboot flash recovery twrp.img"
TWRP HAS BEEN SUCCESSFULLY Installed.
P.S : To boot into twrp : volume up + power on . But it might take 2-3 tries to boot into TWRP . [ I don't yet know why this happens .]
ROOTING :
1. Move SUPER SU and PATCHED BOOT IMAGE into your mobile.
2. Install Super Su.
3. Install Boot Image, Dont forget to select install image and boot partition while installing.
4. You've SUCCESFULLY ROOTED your device .
P.S : PLEASE TRY IT AT YOUR OWN RISK.
Emmc rar does not get extracted... I think the archive is corrupt... Please check onto that
Sent from my Redmi Note 3 using Tapatalk
kirkirehani93 said:
Emmc rar does not get extracted... I think the archive is corrupt... Please check onto that
Sent from my Redmi Note 3 using Tapatalk
Click to expand...
Click to collapse
rar file is just fine , anyway i have uploaded a zip file in the attachment . please check.
reply fast
if i m right... i have to put supersu and boot.img to phone fefore flashing twrp. bcoz after flashing twrp if i reboot to system, phone will not boot and may be bricked...plzzz reply
vivekjha said:
if i m right... i have to put supersu and boot.img to phone fefore flashing twrp. bcoz after flashing twrp if i reboot to system, phone will not boot and may be bricked...plzzz reply
Click to expand...
Click to collapse
No no. It doesn't matter when you put it in. And your after flashing twrp you can directly boot into TWRP and then move the files into mobile.
P.S : While in recovery , you can always copy files in to your mobile.
What if bootloader unlocked officially? Start from "Flashing TWRP" section?
any 1 tried this
any one tried this succesfully plzzz reply
Error during flashing with MiFlash
Got this error during Flashing process:
Status: Not enough storage space is available to process this command.(0x80070008; Max buffer sector is 256)
What should I do? My device does not boot...
anirudh281998 said:
Got this error during Flashing process:
Status: Not enough storage space is available to process this command.(0x80070008; Max buffer sector is 256)
What should I do? My device does not boot...
Click to expand...
Click to collapse
Use Windows 64bit edition.
The flashing process will fail in Windows 32bit edition
will this work in RN3 MTK ???
Will this work on 7.2.5 ?
RedBux said:
will this work in RN3 MTK ???
Click to expand...
Click to collapse
No
Thri11 said:
Use Windows 64bit edition.
The flashing process will fail in Windows 32bit edition
Click to expand...
Click to collapse
Thank you.....i tried it on windows 64 bit and it worked.
I tried unlocking bootload. I got this error "The system cannot find the path specified. (0x80070003: Open Programmer c:...)"
What have I done wrong?
Edit: I deleted the file. Extract it again. Then I unlocked bootloader successfully.
will this void warrenty ?
and to flash miui china roms we need to edit the fastboot everytime ?
When I flash supersu my device won;t boot. Boots fine before though
Hi, I'm on MIUI 7.5.3, can I use 7.2.3 ROM as provided to unlock bootloader or I have to find a 7.5.3 one?
GitGudWolf said:
Hi, I'm on MIUI 7.5.3, can I use 7.2.3 ROM as provided to unlock bootloader or I have to find a 7.5.3 one?
Click to expand...
Click to collapse
I too would like to know the same.
Would this work on 7.5.3 or will I need to do something else
not working sir....
when perform fastboot oem unlock-go, result:
...
FAILED (remote: oem unlock is not allowed)
finished. total time: 0.000s
UPDATE
SOLVED : "Enable OEM unlock" must be turn on in dev option.
SOLVED!
Hi all i just bricked my phone : P9-lite VNS-L31
I managed to unlock bootloader, install twrp and get root permission. Phone worked great. Then i tried to flash xposed and the operation fails due to not enough memory space (!! i have 6gb) and get stuck in bootloop. I made all the possible things i knowed. Tried to use xposed-unistaller.zip (getting other errors like: "no such file o direcory") , wipe cache,dalvik and data and i try also to reflash stock recovery, and to relock bootloader (i can't do that.. why? i get FAILED <remote: command not allowed>) because erecovery and HiSuite can't restore my phone. What can i do?? It's a simple bootloop but i cant restore it. Please help me i have just bought the phone and now i'm very desperate.
I really hope some can help,
Thank you
Can you flash the stock rom through SD card?
Copy the stock rom file to this path: sd card\dload\UPDATE.APP,
Then, presss Volume + , Volume -, and the power keys to force upgrade your phone.
Hi, i solved my problem flashing system.img extracted by an official firmware. Everything ok. If someone need it i can write a little guide now to restore bricked p9-lite with custom recovery and unlocked bootloader (the normal procedure does not work)
Zeph1990 said:
Hi, i solved my problem flashing system.img extracted by an official firmware. Everything ok. If someone need it i can write a little guide now to restore bricked p9-lite with custom recovery and unlocked bootloader (the normal procedure does not work)
Click to expand...
Click to collapse
would you be so kind pls , and could you do the guide for me ? i somehow managed to ruin my phone , i can enter recovery , i can enter erecovery (wont download anything)
but what ever i tried didnt work :/ im getting kinda tilted , cus im trying to solve it for like 7hrs .. and im starting to be alot upset about it .. its like first time i cant repair it my self .. it hurts man (
so thanks for any help
So, i think i can help you to fix your phone.
First of all you need fastboot. So check fastboot drivers on your pc and make sure they work
Now download the stock firmware for VNS-L31 here : http://www.androidvillaz.com/2016/0...vns-l31-to-marshmallow-6.0-b100-firmware.html - It's the only version ready to download and an asian version but flashing only system you'll not notice it. All languages available, no differences at all.
Download and install this tool : http://forum.xda-developers.com/attachment.php?attachmentid=3262545
So using something like 7zip extract the UPDATE.APP file in your desktop for example.
Launch HuaweiUpdateExtractor and select the update.app.
You need to extract SYSTEM.IMG so right click on it and select extract selected.
Now, turn your p9lite in fastboot mode (power off, press vol - and power) and connect it to your pc.
Now launch this : "fastboot flash system "PATH/system.img" " . Remember to replace "PATH/system.img" with the path of your extracted system.img file including the name of the file.
Wait about 3 minutes.
When flash finalize, boot in recovery. Wipe cache and dalvik and reboot your smartphone. It should boot now.
If not, perform a full wipe. (cache,dalvik and data).
Hope this can help.
Zeph1990 said:
So, i think i can help you to fix your phone.
First of all you need fastboot. So check fastboot drivers on your pc and make sure they work
Now download the stock firmware for VNS-L31 here : http://www.androidvillaz.com/2016/0...vns-l31-to-marshmallow-6.0-b100-firmware.html - It's the only version ready to download and an asian version but flashing only system you'll not notice it. All languages available, no differences at all.
Download and install this tool : http://forum.xda-developers.com/attachment.php?attachmentid=3262545
So using something like 7zip extract the UPDATE.APP file in your desktop for example.
Launch HuaweiUpdateExtractor and select the update.app.
You need to extract SYSTEM.IMG so right click on it and select extract selected.
Now, turn your p9lite in fastboot mode (power off, press vol - and power) and connect it to your pc.
Now launch this : "fastboot flash system "PATH/system.img" " . Remember to replace "PATH/system.img" with the path of your extracted system.img file including the name of the file.
Wait about 3 minutes.
When flash finalize, boot in recovery. Wipe cache and dalvik and reboot your smartphone. It should boot now.
If not, perform a full wipe. (cache,dalvik and data).
Hope this can help.
Click to expand...
Click to collapse
with pressing volume - and power i enter into erecovery from there i should use fastboot to flash system.img ? sorry for being dum
edit: when in erecovery (volume- and power) typing fastboot flash system with full path , does nothing .. only saying waiting for device
edit2: no matter what i do , i cant fastboot flash system .. waiting for device .. only thing i can do is enter TWRP (also got root) , enter Erecovery and thats it .. phone only boots to huawei animation along wiht sound and thats it .. i tried adb sideload from TWRP but no help also .. guess there is nothing i can do right ?
Edit3: so i booted via TWRP to bootloader , used that fastboot command , flashed system , wiped cache , and now it is looking that phone is booting up !
thanks bro , any way i can pay you back ? cus you da MVP here !
EDIT4: well phone booted , rebooted , and now i cant enter recovery it boots into erecovery and i cant do nothing else
EDIT5: got into fastboot menu in phone , it says update system again , Error Func NO : 10 (boot image) Error NO : 2 (load failed)
EDIT6: somehow made it into fastboot , somehow flashed recovery , managed to restore my phone from back up , but sadly enough i cant restore it via google , since when i try to log in it says waiting .. dam this phone . i had galaxy S .. got this huawei just for pokemon go (which is pretty ****ty without gyro) FML right
EDIT7: lost most of my hairs .. some of them were ripped out in some anger explosions .. chewed of some of my nails .. but somehow i made it ! now if i only could unroot and relock bootloader xD think im gonna take a break for now and when my nerves will calm down i may try it again . Rly wanna thank you from all of my heart for help , thanks !! your the best man , thanks again
Sorry, can you normally boot and use your phone now?
Edit: It seems you can boot. Now you have restored your twrp recovery. I don't know why you have problems with google log in, but hey now it boots!
Zeph1990 said:
Sorry, can you normally boot and use your phone now?
Edit: It seems you can boot. Now you have restored your twrp recovery. I don't know why you have problems with google log in, but hey now it boots!
Click to expand...
Click to collapse
i cant thank you enough , without you i couldnt achieve this so thanks again !!
finaly did everything .. and only thing left is get bootloader locked and unroot it hope i will somehow find the way
So happy to hear it! =)
I tried also to relock bootloader during my attempts to unbrick the phone but i fail.. i don't know why, but i think someone was able to do it.
Zeph1990 said:
Now, turn your p9lite in fastboot mode (power off, press vol - and power) and connect it to your pc.
Now launch this : "fastboot flash system "PATH/system.img" " . Remember to replace "PATH/system.img" with the path of your extracted system.img file including the name of the file.
Hope this can help.
Click to expand...
Click to collapse
Where did you launch the command? I can't do it in the huawei update extractor... Please help!!
Thank you.
ElPinguShow said:
Where did you launch the command? I can't do it in the huawei update extractor... Please help!!
Thank you.
Click to expand...
Click to collapse
Hi, if you don't know what is fastboot maybe you can approach it the easy way.
Download and install this for the correct drivers : http://consumer.huawei.com/minisite/HiSuite_en/index.html
Download and extract to a folder this : https://mega.nz/#!B4tATA5D!-TseQ9A-TPEQhzNQRXsT_cV2i4T7qYYLadceW0fM8k0
Put your phone in fastboot mode : Turn it off. Connect it to your pc . Long press vol - and power until it boots in fastboot mode (white screen with a green android and other stuff). If you want you can boot in fastboot from TWRP recovery : restart -> bootloader.
Copy your extracted SYSTEM.IMG in the root path of the tool (we can assume its name is system.img).
Now launch the tool and press 000 and enter.
If you have done all right now you can give this : fastboot flash system system.img
Wait about 3 minutes. Perform a cache and dalvik cache wipe. Boot your phone.
Zeph1990 said:
So, i think i can help you to fix your phone.
First of all you need fastboot. So check fastboot drivers on your pc and make sure they work
Now download the stock firmware for VNS-L31 here : http://www.androidvillaz.com/2016/0...vns-l31-to-marshmallow-6.0-b100-firmware.html - It's the only version ready to download and an asian version but flashing only system you'll not notice it. All languages available, no differences at all.
Download and install this tool : http://forum.xda-developers.com/attachment.php?attachmentid=3262545
So using something like 7zip extract the UPDATE.APP file in your desktop for example.
Launch HuaweiUpdateExtractor and select the update.app.
You need to extract SYSTEM.IMG so right click on it and select extract selected.
Now, turn your p9lite in fastboot mode (power off, press vol - and power) and connect it to your pc.
Now launch this : "fastboot flash system "PATH/system.img" " . Remember to replace "PATH/system.img" with the path of your extracted system.img file including the name of the file.
Wait about 3 minutes.
When flash finalize, boot in recovery. Wipe cache and dalvik and reboot your smartphone. It should boot now.
If not, perform a full wipe. (cache,dalvik and data).
Hope this can help.
Click to expand...
Click to collapse
Hi,
I am using the standard P9, and getting the Boot Loop also.
I attempted your instructions, and appeared to work - I got the first EMUI initialization screen - and now its gone back to how it was.
Any suggestions?
I think it should work on every phone assuming you are using the right firmware. Do you use the right firmware for the huawei P9 ?? (needless to say it's not the version i posted)).
So if you flashed the right firmware (and i'm pretty sure of this) my advice is to perform a full wipe : Cache, dalvik and data.
If you are still facing the same error consider flashing other frimware parts like boot.img ecc.
I believe so - I am pretty clueless with this stuff.
By firmware, do you mean the stock version? Because I used P9-EVAL09-EVA-B136. Don't suppose you would know the right firmware I require?
I think it's the right version. I am a p9lite user so i don't know specifically the right version of the firmware but i think it's ok. Do you tried a full wipe?
Zeph1990 said:
I think it's the right version. I am a p9lite user so i don't know specifically the right version of the firmware but i think it's ok. Do you tried a full wipe?
Click to expand...
Click to collapse
How can I perform a full wipe? Thanks for replying by the way
So, do you have unlocked bootloader and custom recovery (TWRP) ?
Zeph1990 said:
So, do you have unlocked bootloader and custom recovery (TWRP) ?
Click to expand...
Click to collapse
I do yes
So, go in twrp recovery (turn off phone, long press vol up and power for at least 3 seconds). When you are in you will see 'WIPE' press it then do the swipe to Factory Reset. You will lost your installed apps and the relative settings but you will not lost your personal stuff such photo,music documents ecc. Let me know if you perform it and if it works =)
It appears that TWRP no longer appears. I get thr EMUI options to wipe data/factory reset. But once I do this I just get a red exclamation mark.
Does the phone need to be plugged in via USB?
Hello,
I was always a Samsung fanboy, but than I decided to buy the P9 lite (VNS-L21 single sim)
I wanted to flash the android 7 update for my phone, but I was such a noob in Huawei, that I didn't understand a word. But i tried to do what the instructions said. Now my phone is bricked. I can go to recovery, erecovery (which can't download anyithing) and download mode. I heard of this fastboot stuff as well, but I don't know how to do this. I tried to flash as many roms as I could with dload and it didn't work, after 5%, it said it failed... Now I don't know what to do. I think somebody (expert) should make a clear tutorial for noobs. Oh and I almost forgot that i don't have root, custom recovery, and things like that. I just bought the phone, I didn't want to make big changes, just new android. Is it possible that after this Huawei would fix my phone, if I couldn't? Or warranty is void? And sadly I don't know more of my phone because I'm not ina rom, and the phone and papers don't say more.
If you could help me, I would appreciate it:
Raul
Turn off your phone, connect to the pc while holding the volume down button, you will end up in fastboot mode.
I assume you have ADB and drivers installed (if not, install ADB and device drivers).
Optional: unlock your bootloader if it's locked.
Download the latest offical rom zip for your phone version (the marshmallow one), extract the update.app.
Use Huawei extractor to ectract the following files (google is your friend in this one, but its not difficult):
boot.img
recovery.img
cust.img
system.img
After you've done this, connect your phone to the PC in fastboot mode .
Open a command promt from the folder where the extracted files are (shift+right click, Open Command window here), enter the following commands
fastboot devices (you will see the list of attached devices with a lot of random number + fastboot)
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash cust cust.img
fastboot flash system system.img
fastboot reboot
After all this, you should be good to go, just be sure you are using the correct rom for you version.
Or you can just serach on the forum and find this.
https://forum.xda-developers.com/huawei-p9lite/help/unbricking-vns-l21-vns-l31-tutorial-t3583400
(Sorry for my english.)
Fastboot says that it has failed command not alllowed, after I want to installl the files. And I couldn't unlock bootloader without phones information...
rr999999 said:
I would happily unlock my bootloader, but I don't know anyithing about my phone (except model...) without the os...
Click to expand...
Click to collapse
Post here IMEI and SN from the box of phone and i can try get your bootloader unlock code...
If I would unlock it, would fastboot work? Because fastboot pc app recognizes my phone, but my phone says in fastboot mode, that I should connect itself to pc and open hisuite. WTF?
rr999999 said:
If I would unlock it, would fastboot work? Because fastboot pc app recognizes my phone, but my phone says in fastboot mode, that I should connect itself to pc and open hisuite. WTF?
Click to expand...
Click to collapse
Until you have bootloader unlock you can not run any fastboot flash command...
rr999999 said:
If I would unlock it, would fastboot work? Because fastboot pc app recognizes my phone, but my phone says in fastboot mode, that I should connect itself to pc and open hisuite. WTF?
Click to expand...
Click to collapse
Heyho,
normally yes, after bootloader unlock u are able to flash via fastboot. But...
I tried to flash as many roms as I could with dload and it didn't work, after 5%, it said it failed...
Click to expand...
Click to collapse
What is the error? - Have u disconnected the device from the PC during the update?
If not, try to update again and just disconnect the device from any USB connection...
Regards,
Sebastian
k1ll3r8e said:
Heyho,
normally yes, after bootloader unlock u are able to flash via fastboot. But...
What is the error? - Have u disconnected the device from the PC during the update?
If not, try to update again and just disconnect the device from any USB connection...
Regards,
Sebastian
Click to expand...
Click to collapse
Hello. I disconnected it from everything (for example USB)When I tried to install it said something like incompatibility version, but it couldn't be because I tried many roms for my phone. And I tried some dual sim roms as well because, I thought that it might work... But then I will do that unlock if it will do good. Thanks for the help Without bootloader I can't flash from dload as well?
rr999999 said:
Hello. I disconnected it from everything (for example USB)When I tried to install it said something like incompatibility version, but it couldn't be because I tried many roms for my phone. And I tried some dual sim roms as well because, I thought that it might work... But then I will do that unlock if it will do good. Thanks for the help Without bootloader I can't flash from dload as well?
Click to expand...
Click to collapse
Heyho,
the dload method works always without unlock bootloader. But, u can't flash for example an B161 over an B3xx (what nougat is) if the update u installed modified already the oeminfo u are not able to flash any rom below B3xx (nougat) via dload.
-
In that case u might use the official rollback package (never tested it myself) or, u unlock ur bootloader, flash a TWRP recovery matching to ur current FW. Flash from there a oeminfo + custom.bin (lower than B3xx) and flash the FW matching to the new oeminfo via dload and stock recovery.
Regards,
Sebastian
If you have custom recovery, wipe everything. Data, system, boot. extract update app (which is your stock rom) with huawei update extractor. go to custom recovery, flash stock boot IMG and stock recovery IMG. Power off, use three button dload method, reboot, when booting press vol up for three second, now you are in e-recovery. Press shutdown. Press and hold power and vol up for stock recovery. Do factory reset. If need do the factory reset 2/3 times. Now you are with locked bootloader.
Sent from my NEM-L21 using Tapatalk[/QUOTE]
Sent from my NEM-L21 using Tapatalk
today , I unlocked the bootloader of my Real Me 2 Pro and everything was fine and after I tried to boot it back to system after flashing magisk and the decryption.zip , I got this message saying " The current boot / recovery image have been destroyed and can not boot. Please flash the correct image or contact customer service to fix it"
I can just flash the official firmware or any ohter ROM but the PC can't seem to detect the fastboot mode and neither am I able to boot into fastboot / recovery.
can someone please help.!
vishnusai.karumuri said:
today , I unlocked the bootloader of my Real Me 2 Pro and everything was fine and after I tried to boot it back to system after flashing magisk and the decryption.zip , I got this message saying " The current boot / recovery image have been destroyed and can not boot. Please flash the correct image or contact customer service to fix it"
I can just flash the official firmware or any ohter ROM but the PC can't seem to detect the fastboot mode and neither am I able to boot into fastboot / recovery.
can someone please help.!
Click to expand...
Click to collapse
Hi, how about your phone? is your problem have solved?
i have same problem like you. and i want to know about to solve it
thank you
hi, my problem a bit different with recovery.
i have stock recovery with unlocked bootloader. im with coloros 5.2 and can not install coloros 6 update. stock recovery cant find update file in phone storage, wifi doesnt work and starting update from os, returns update failed after one reboot. and suggestion?
vishnusai.karumuri said:
today , I unlocked the bootloader of my Real Me 2 Pro and everything was fine and after I tried to boot it back to system after flashing magisk and the decryption.zip , I got this message saying " The current boot / recovery image have been destroyed and can not boot. Please flash the correct image or contact customer service to fix it"
I can just flash the official firmware or any ohter ROM but the PC can't seem to detect the fastboot mode and neither am I able to boot into fastboot / recovery.
can someone please help.!
Click to expand...
Click to collapse
I face the same issue. Flashed twrp. Then flashed boot+magisk+patched img file. Now the phone halts at the fastboot mode and is not booting up. It also unable to be power off. plz help. The model is Realme2 RMX 1805
Dont worry you do have a unlocked device so u need a pc to do that download system.img, vendor.img for your device and just open cmd then type this fastboot flash system system.img then fastboot flash vendor vendor.img and reboot it second method if you dont have an pc not sure that it will work you need a second device with otg support download bugjaeger app from playstore and use the same commands which i mention in pc method
Hello guys! i have the same problem as this guy here:
HELP! Hardbricked p10 lite after dload update
Apparently I played way too much with my p10 lite and managed to get it bricked very badly... I can't get to any kind of recovery mode, erecovery, update menu for dload, I can only get to fastboot mode, when I try to boot into the rom or into...
forum.xda-developers.com
LET'S BEGIN OUR JOURNEY:
i follow this guide succesfully:
P10 lite bootloader unlock (June 2020, Windows install)
Damn, it's been a while since I was here. Back then it was mostly about Windows PDAs. Disclaimer: Your warranty after this process is void and your phone will tell you it can not be trusted because it's unlocked. This is what worked for me. I...
forum.xda-developers.com
so since i downgraded to emui 5 i wanted to upgrade to emui 8 (for custom roms) but with OTA was not working
then i managed to flashed twrp (3.1.x.x) succesfully cause the new ones were not working
but with this recovery i couldn't flash anything! and i had already wiped everything out! (data, dalvik cache, system, etc...)
i tried to flash new twrp version through twrp, but i didn't worked!
i decided to flash stock firmware (emui 5) with force dload method (phone off, pressing all 3 buttons together, you know...)
https://androidhost.ru/JT (Warsaw-L21 C432B182 EU SERVICE)
with this, GUESS WHAT, i soft bricked it, i couldn't boot BUT dload, erecovery, etc...were working!
so i follow this guide flashing stock firmware (emui 8) with force dload method:
Service Roms -DLOAD for C432,upgrade O-O or N-O, unbrick, locking bootloader, etc
Finally Service roms for Emui 8 provided by Huawei . Only for EU models - C432 Same Service roms could be used for upgrade from Emui 5 to Emui 8, and its a new possibility. But please be careful for upgrading from emui 5 to emui 8 you should be...
forum.xda-developers.com
but i think i just hard bricked my device.
the phone boots in error mode
func NO: 11 (recovery image)
error NO: 2 (load failed!)
i can't use dload, erecovery, or twrp (or stock recovery)
only fastboot works
when i'm trying to flash something in fastboot mode (ex recovery or boot.img) i get the error
FAILED (remote: partition length get error)
DEVICE INFO:
huawei p10 lite (4gb / dual sim)
fastboot oem get-bootinfo
(bootloader) unlocked
fastboot oem get-psid
(bootloader) SN: obscured (if you need it tell me)
(bootloader) IMEI: obscured (if u need it tell me)
(bootloader) IMEI1:000000000000000
(bootloader) MEID:00000000000000
fastboot oem get-build-number
(bootloader) :WAS-LX1AC02B141
fastboot oem get-product-model
(bootloader) WAS-LX1A
fastboot getvar vendorcountry
vendorcountry: vodafone/default (this appears now, cause the first emui 5 firmware i flashed was vodafone branded)
My bootloader and FRP are UNLOCKED
thanks a lot to everybody, if you need any other details just tell me!
Hi...
what about HWOTA-WAS Methode? There you can change Region from C02 to any other. If you didnt have the 3 package Firmware for that. Let me know...i can upload my B398C432 for 4GB dual sim firmware. You can
also try to only extract the oeminfo from same named folder and flash it by fastboot command
fastboot flash oeminfo xxxxxxxxx.img
If its no image then Rename it from xxxxxxxxx to xxxxxxxxx.img
But hey heads up...nothing is lost
solong
speedson
speedson said:
Hi...
what about HWOTA-WAS Methode? There you can change Region from C02 to any other. If you didnt have the 3 package Firmware for that. Let me know...i can upload my B398C432 for 4GB dual sim firmware. You can
also try to only extract the oeminfo from same named folder and flash it by fastboot command
fastboot flash oeminfo xxxxxxxxx.img
If its no image then Rename it from xxxxxxxxx to xxxxxxxxx.img
But hey heads up...nothing is lost
solong
speedson
Click to expand...
Click to collapse
thanks man! yes please, can you upload it? I'll try what you suggest for sure
Mcgreygor said:
thanks man! yes please, can you upload it? I'll try what you suggest for sure
Click to expand...
Click to collapse
OK for sure I will do it even im back at home and infront of my Computer.
solong
speedson
Here these 2 zip´s waiting for your download. Keep in mind...an unlocked bootloader is needet^^
HWOTA - Google Drive
drive.google.com
HWOTA-WAS-Eng is the tool
HWOTA are the 3 parts of the Firmware
unzip the tool ( HWOTA8_WAS is what we want ) and unzip the 3 parts of firmware
copy and paste the 3 parts of firmware into the HWOTA8_WAS / update folder
then connect the Phone ( fastboot mode ) to the PC
start the process by execute the update_eng.bat
when asked whether it should be repacked or already is .... it is already repacked
when asked for Source...choose Script
now the !!!!what would you do!!! choose 2 for !!!!!!change location!!!!! that you go away from the C02 European-Vodafone Brandt straight to the one you want WAS-LX1AC432
follow the prcess to the End
hope it help you by unbrick/restore your Phone...good luck bro
solong
speedson
if this had not work cause of bla blub idont know....we try another Option with Multi-Tool and Huawei-firmware-extractor
thanks man! i tried, but when i have to reboot to twrp recovery, the phone boots in error mode
again:
func no: 11 (recovery image)
error no: 2 (load failed!)
Mcgreygor said:
thanks man! i tried, but when i have to reboot to twrp recovery, the phone boots in error mode
again:
func no: 11 (recovery image)
error no: 2 (load failed!)
Click to expand...
Click to collapse
Hi...
in your first post you write that dload doesnt work for you. So how did you doing it?
Wich firmware package you choose for dload method---have a link?
How did you config the external sd and the dload folder?
solong
speedson
speedson said:
Hi...
in your first post you write that dload doesnt work for you. So how did you doing it?
Wich firmware package you choose for dload method---have a link?
How did you config the external sd and the dload folder?
solong
speedson
Click to expand...
Click to collapse
wait...there is some confusion here i think hahaha
yes! dload method DOESN'T WORK so i tried your method.
i follow the guide and when i use "update_eng.bat" it flashes the twrp recovery and then it asks to reboot to recovery but it doesn't work!
Hello ,
mee too I had this issue so what I did maybe you need to be patient . you will push dload ( the idea is to try every firmware even if not compatible with your phone result just worked your phone )
1 - if I undertand well you are using a wrong recovery.img ( same issue happed with me) I use a lot of and what is compatible for me is twrp_p10_lite_0.4.img - fixed mount issues ( LINK ) you can try all of them if this one does not open twrp well but I guess that will help you .
2 - if you could open the TWRP make a full wip everything . delete all systems data .... everything .
3 - here you need to be patient please : donwload all huawei dual SIM and try one by one download this FIRMWARE
4 - put the file exactly as this HERE @Thanks to Alexxx1
5 - if we suppose after many tries you have the chance to get phone worked and you will see that the BUILD NUMBER is like that 8.0.0.046 (xyz)
6 - connect your phone using HI SUITE then update from HI SUITE . you will see that you are in the last version of EMUI and try another version . click on it . you will see the exact Firmware of your device but android 7 not problem you can get latest update after easily .as always .
try this and I hop that I helped you .
BR
Mcgreygor said:
wait...there is some confusion here i think hahaha
yes! dload method DOESN'T WORK so i tried your method.
i follow the guide and when i use "update_eng.bat" it flashes the twrp recovery and then it asks to reboot to recovery but it doesn't work!
Click to expand...
Click to collapse
Hi...
ok guys.....dont try anything other...keep on being at the HWOTA ok sweethearts. The HWOTA progress is starting and flashing the TWRP recovery...then it ask to reboot to recovery but nothing happens right? The Answer is very simple.
There doesnt exist a fastboot command to directly reboot from fastboot to recovery like
fastboot reboot-recovery (this command would be nice but its not existing)
so what is to do for you after TWRP was flashed successfully...the script is waiting for the boot into recovery. you need to do it manually by unplug the usb cable from the Phone and then press pwr button for so long that the screen turns into black-shut off the phone you know.
even the screen is tunred into black (the phone is shut-off) instantly press and hold Vol-up key for so long until you see the Huawei Logo...Pwr-Key not needet cause Phone is power-up by it selfe.
you should now enter recovery-mode....now reconnect the usb cable and in the HWOTA script press enter and follow the instructions in the blue screen script and dont forget we want to change the Region. That you leave the C02 Vodafone branding firmware to c432 European no branding.
for the latest step the script ask you to relock the bootloader or let him unlocked...so let him unlocked if you not have a unlock-code and if you want to flash a custom rom later.
ennadif said:
Hello ,
mee too I had this issue so what I did maybe you need to be patient . you will push dload ( the idea is to try every firmware even if not compatible with your phone result just worked your phone )
1 - if I undertand well you are using a wrong recovery.img ( same issue happed with me) I use a lot of and what is compatible for me is twrp_p10_lite_0.4.img - fixed mount issues ( LINK ) you can try all of them if this one does not open twrp well but I guess that will help you .
2 - if you could open the TWRP make a full wip everything . delete all systems data .... everything .
3 - here you need to be patient please : donwload all huawei dual SIM and try one by one download this FIRMWARE
4 - put the file exactly as this HERE @Thanks to Alexxx1
5 - if we suppose after many tries you have the chance to get phone worked and you will see that the BUILD NUMBER is like that 8.0.0.046 (xyz)
6 - connect your phone using HI SUITE then update from HI SUITE . you will see that you are in the last version of EMUI and try another version . click on it . you will see the exact Firmware of your device but android 7 not problem you can get latest update after easily .as always .
try this and I hop that I helped you .
BR
Click to expand...
Click to collapse
Hi...
8.0.0.046(xyz) is a bug mode that means it is a wrong boot image in the System with a security patch from 2018 if i remeber correctly. The HiSuit could not help for his Problem cause he had a wrong brandet firmware flashed. btw HiSiute also doesnt help by anything that you try to fix...you Device is not supportet is the standart answer from HiSuite...its a bull**** tool like every other bull**** tool from other Customers like Samsung Sony bla blub.
So let us go the HWOTA way to really fix his issue and to get his Device working like it should I know that will work pretty well.
solong
speedson
speedson said:
Hi...
ok guys.....dont try anything other...keep on being at the HWOTA ok sweethearts. The HWOTA progress is starting and flashing the TWRP recovery...then it ask to reboot to recovery but nothing happens right? The Answer is very simple.
There doesnt exist a fastboot command to directly reboot from fastboot to recovery like
fastboot reboot-recovery (this command would be nice but its not existing)
so what is to do for you after TWRP was flashed successfully...the script is waiting for the boot into recovery. you need to do it manually by unplug the usb cable from the Phone and then press pwr button for so long that the screen turns into black-shut off the phone you know.
even the screen is tunred into black (the phone is shut-off) instantly press and hold Vol-up key for so long until you see the Huawei Logo...Pwr-Key not needet cause Phone is power-up by it selfe.
you should now enter recovery-mode....now reconnect the usb cable and in the HWOTA script press enter and follow the instructions in the blue screen script and dont forget we want to change the Region. That you leave the C02 Vodafone branding firmware to c432 European no branding.
for the latest step the script ask you to relock the bootloader or let him unlocked...so let him unlocked if you not have a unlock-code and if you want to flash a custom rom later.
Hi...
8.0.0.046(xyz) is a bug mode that means it is a wrong boot image in the System with a security patch from 2018 if i remeber correctly. The HiSuit could not help for his Problem cause he had a wrong brandet firmware flashed. btw HiSiute also doesnt help by anything that you try to fix...you Device is not supportet is the standart answer from HiSuite...its a bull**** tool like every other bull**** tool from other Customers like Samsung Sony bla blub.
So let us go the HWOTA way to really fix his issue and to get his Device working like it should I know that will work pretty well.
solong
speedson
Click to expand...
Click to collapse
Hello Speedson ,
Your are the master , am not a develpooer and I have 1 % knowledge on firmware . but Hisuite helped me really . when I had the wrong boot 8.0.0.046 (xyz ) I just go to system update then other version . really Hisuite gived me emui 5 as version with my build number exactly .
anyway your methode could help more . put no one will lose if try this solution as fin,al solution.
BR
thanks guys so much! for helping me, you are so sweet! <3
ennadif said:
Hello ,
mee too I had this issue so what I did maybe you need to be patient . you will push dload ( the idea is to try every firmware even if not compatible with your phone result just worked your phone )
1 - if I undertand well you are using a wrong recovery.img ( same issue happed with me) I use a lot of and what is compatible for me is twrp_p10_lite_0.4.img - fixed mount issues ( LINK ) you can try all of them if this one does not open twrp well but I guess that will help you .
2 - if you could open the TWRP make a full wip everything . delete all systems data .... everything .
3 - here you need to be patient please : donwload all huawei dual SIM and try one by one download this FIRMWARE
4 - put the file exactly as this HERE @Thanks to Alexxx1
5 - if we suppose after many tries you have the chance to get phone worked and you will see that the BUILD NUMBER is like that 8.0.0.046 (xyz)
6 - connect your phone using HI SUITE then update from HI SUITE . you will see that you are in the last version of EMUI and try another version . click on it . you will see the exact Firmware of your device but android 7 not problem you can get latest update after easily .as always .
try this and I hop that I helped you .
BR
Click to expand...
Click to collapse
Thanks Man! but i already tried with that twrp image
it doesn't work...it always say:
fastboot flash recovery twrp_p10_lite_0.4.img
Sending 'recovery' (24954 KB) OKAY [ 0.656s]
Writing 'recovery' FAILED (remote: 'partition length get error')
fastboot: error: Command failed
fastboot flash ramdisk_recovery twrp_p10_lite_0.4.img
Sending 'ramdisk_recovery' (24954 KB) OKAY [ 0.657s]
Writing 'ramdisk_recovery' FAILED (remote: 'partition length get error')
fastboot: error: Command failed
either cases
speedson said:
Hi...
ok guys.....dont try anything other...keep on being at the HWOTA ok sweethearts. The HWOTA progress is starting and flashing the TWRP recovery...then it ask to reboot to recovery but nothing happens right? The Answer is very simple.
There doesnt exist a fastboot command to directly reboot from fastboot to recovery like
fastboot reboot-recovery (this command would be nice but its not existing)
so what is to do for you after TWRP was flashed successfully...the script is waiting for the boot into recovery. you need to do it manually by unplug the usb cable from the Phone and then press pwr button for so long that the screen turns into black-shut off the phone you know.
even the screen is tunred into black (the phone is shut-off) instantly press and hold Vol-up key for so long until you see the Huawei Logo...Pwr-Key not needet cause Phone is power-up by it selfe.
you should now enter recovery-mode....now reconnect the usb cable and in the HWOTA script press enter and follow the instructions in the blue screen script and dont forget we want to change the Region. That you leave the C02 Vodafone branding firmware to c432 European no branding.
for the latest step the script ask you to relock the bootloader or let him unlocked...so let him unlocked if you not have a unlock-code and if you want to flash a custom rom later.
Hi...
8.0.0.046(xyz) is a bug mode that means it is a wrong boot image in the System with a security patch from 2018 if i remeber correctly. The HiSuit could not help for his Problem cause he had a wrong brandet firmware flashed. btw HiSiute also doesnt help by anything that you try to fix...you Device is not supportet is the standart answer from HiSuite...its a bull**** tool like every other bull**** tool from other Customers like Samsung Sony bla blub.
So let us go the HWOTA way to really fix his issue and to get his Device working like it should I know that will work pretty well.
solong
speedson
Click to expand...
Click to collapse
Hey man! thanks again for reply
the command "fastboot reboot recovery" actually exist, and works with many models, but not all of them
with the p10 lite, it works:
fastboot reboot recovery
Rebooting into recovery OKAY [ 0.018s]
Finished. Total time: 0.034s
the problem is, i still get "error mode"
even if i try with the "power on + volume up" combo...still...error mode
@speedson would you like to do a teamviewer session to my computer?
and a telegram videocall to see the phone?
what you think?
i have the same issue. Speedson`s way is working but i cant seem to find a way to charge my phone either on error mode or on fastboot.
Upon restart there is a red lightining and the phone isnt rebooting if i take off any cable. just black screen as if it is not charged. when i connect the cable with pc it wont boot to recovery because its connected.
dimutris said:
i have the same issue. Speedson`s way is working but i cant seem to find a way to charge my phone either on error mode or on fastboot.
Upon restart there is a red lightining and the phone isnt rebooting if i take off any cable. just black screen as if it is not charged. when i connect the cable with pc it wont boot to recovery because its connected.
Click to expand...
Click to collapse
yep, same issue now...i can't offline charge my phone
red blinking and the phone goes OFF
i can only use fastboot mode with usb plugged in
Do you think its possible the issue of not charging to be because of the software or maybe the charging port is somewhat damaged?
I mean it could be possible that we both might have damaged the charging port. However i cant see anywhere some info about that issue. Can we for sure know that the phone charges on error mode or on bootloader, or is itfor sure a software issue?
speedson said:
Here these 2 zip´s waiting for your download. Keep in mind...an unlocked bootloader is needet^^
......
solong
speedson
if this had not work cause of bla blub idont know....we try another Option with Multi-Tool and Huawei-firmware-extractor
Click to expand...
Click to collapse
I have the exact same problem, but my phone is WAS-LX1C432 (p10lite dual sim with 3gb ram). Could you please upload the HWOTA for WAS-LX1C432?
dimutris said:
Do you think its possible the issue of not charging to be because of the software or maybe the charging port is somewhat damaged?
I mean it could be possible that we both might have damaged the charging port. However i cant see anywhere some info about that issue. Can we for sure know that the phone charges on error mode or on bootloader, or is itfor sure a software issue?
Click to expand...
Click to collapse
What's the output you get from this command: fastboot getvar battery-voltage
getvar:battery-voltage FAILED (remote: Command not allowed)