Database Users

(resolve) qtek 9090 bloked on the withe screen after WM6 UP... need help

hello every one
i'm noob & i speak french so excuse me if my it's a lil bit hard to on understand my topic .
-after installing WM6 on my qtek 9090 i flowed the steps and then at the end
when i press the mail button the white screen appear & it still (when "welcome... " is supose appear after 30sec.
when i reset i see the bootscreen (clored stripes),i folow the steps but it still blokeded on the withe screen.
& i tried using others wm6 rom but the problem still the same
So i wanted to know if there is away to fix it??
-I tried to downgrade but it doesn't because i don't use the good rom i think.
what can i do??
-i have no acces to ppc from actyvesync
in boatloder it show v 1.02 & the 3 colors band shows :
NO GSM
D 6.00.00.WWE
thanks for your help

There is no problem with your BA. Try to do the setup again...
NOW....
Before you upgrade your BA keep this is mind...it's a warning...a WARNING so you will not sue xda-dev or any BA ROM cooker if something BAD happens to your BA. But don't worry 1 out of 1000 BA owners brick their BA while upgrading. Because they upgrade their BA with 10% battery life. Where did I get the 1 out of 1000 statistics? Just a guess..a wild guess but it's near to reality
WARNING
IF YOU PROCEED, YOU MAY TOAST YOUR PHONE. THERE'S NO COMEBACK. THERE'S NO GETTING ROUND THIS. READ THE INSTRUCTIONS FIRST OTHERWISE YOU'LL PROBABLY BREAK YOUR PHONE PERMANENTLY. THIS WILL VOID YOUR WARRANTY. DO YOU UNDERSTAND? DO YOu? ANSWER ME YOU...lol
Click to expand...
Click to collapse
- Download unlocker.cab DOWNLOAD HERE
- Download Repart_Doc.exe DOWNLOAD HERE
- Place both of them somewhere on your Pocket PC. For example in \temp but anywhere is fine. All the command below are to be executed on your Pocket PC, not on your PC.
- Install xda-developers_Unlocker.CAB by tapping on it in filemanger (from the directory where you put it earlier)
- Then go to start -> Programs -> ExtROM tools -> then first run "unhide", then "Unlock".
- Do a soft reset. (you know how to do a SR, right?)
- Once your Pocket PC is restarted, locate the Repart_DOC.exe file with your filemanager and start it.
- Set the size of Extended ROM to 128 kb (which is already the default).
- Press "Format now!" and wait until it is done (A few seconds). You will see a message that it is done. (You will get an error message about your storage, just press yes and wait a few seconds.)
- Soft reset your Pocket PC.
NOW YOU ARE DONE WITH THE FIRST PART AND I HOPE I AM MAKING IT EASY FOR YOU AND FOR EVERYONE.
Now, I RECOMMEND you to use Windows XP and of course Active Sync 4.5.
NOTE: Do a hard reset first
Doing a hardreset is easy if you have 3 hands - push your stylus at the softreset hole and then as soon as you see the Strips
hold Camera and Record
Then you will be a debugger screen
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Navigation in menu is done with camera and record buttons.
reset registry and format built-in storage
“Enable KITL” must be NO “Clean Registry Hive” must be YES “Format Storage” must be YES exit - "mail" button
You will know if you have performed a hard reset if you are lead through the setup of your device section. All else is just a softreset.
Click to expand...
Click to collapse
1. Download the BA ROM that you desired. It can be WM6, WM6.1 or WM6.5 and you can find all the download links of this ROMs on our BA wiki (and I am the one who updated that and put those links.)
2. Save that ROM on your computer. (anywhere will do) If it is zipped or rar, then unzip it or unrar it.
Here are the files that should be inside that ROM folder (well this are the files that I have every time I flash my BA, just correct me guys if some of this are not really needed):
EnterBL.exe
GetDeviceData.exe
HTCRUU.dll
RUU.dll
BaUpgradeUt.exe
MaUpgradeUt_noID.exe
HTCRUU.conf
RUU.conf
vbscript.dll
nk.nbf
SetOperator.bat
3. Temporarily remove your SD Card (it may work for you with the SD card still in your BA, but you may not be able to enter USB mode when cradled).
Just remove your SD Card from you BA and the SIM card too just to make sure.
4. Put your device into Bootloader mode by pressing and holding the "Power" & "Record" buttons, and then press the Reset Button. Ooops before I forgot make sure you do a Hard Reset on your BA first.
Press and hold the "Power" & "Record" buttons, and then press the Reset Button until “Serial” shows on screen.
(Some BlueAngel shows "Serial" at the top and "V2.07" at the bottom.)
NOTE: The screen will not be backlit, so it may appear the phone is not in bootloader mode.
Look carefully.
When the USB sync cable is inserted into the phone and the computer, "Serial" will change to "USB", provided that the phone detects the connection.
5. Connect the phone to the sync cable/cradle.
7. Now you can execute the installer file. (BaUpgradeUt.exe or MaUpgradeUt.exe) You will see this window:
8. When the upgrade is completed, you must perform a Hard Reset.
When the bootscreen, aka. the colored stripes is displayed, wait more, you are booting. The welcome screen to set up your device will appear shortly ...

thanks but there is a problem i have no acces to ppc from my computer & actvivesync dont localize it.

try THIS method, there is no need to reflash, you canceled the hard reset and now the things are f***ed up. so if another button hard reset does not help then MTTY method is your only hope

i did what the tutorial says but when mtthy i don't know wht to do cuz it don't correspond whit the tutorial

azdd said:
i did what the tutorial says but when mtthy i don't know wht to do cuz it don't correspond whit the tutorial
Click to expand...
Click to collapse
in port select USB or WCEUSBXXXXXX

& where must I type ???

azdd said:
& where must I type ???
Click to expand...
Click to collapse
In the MTTY window

i see USB i click on it & then i have a windows it's look like a text editor.then i type for exmeple "set 140" but after that i dont know what to do i tried autodownload but i got a msg like "input full name...."
so wht's the next step??

red_hanks said:
1. Download the BA ROM that you desired. It can be WM6, WM6.1 or WM6.5 and you can find all the download links of this ROMs on our BA wiki (and I am the one who updated that and put those links.)
2. Save that ROM on your computer. (anywhere will do) If it is zipped or rar, then unzip it or unrar it.
Here are the files that should be inside that ROM folder (well this are the files that I have every time I flash my BA, just correct me guys if some of this are not really needed):
EnterBL.exe
GetDeviceData.exe
HTCRUU.dll
RUU.dll
BaUpgradeUt.exe
MaUpgradeUt_noID.exe
HTCRUU.conf
RUU.conf
vbscript.dll
nk.nbf
SetOperator.bat
3. Temporarily remove your SD Card (it may work for you with the SD card still in your BA, but you may not be able to enter USB mode when cradled).
Just remove your SD Card from you BA and the SIM card too just to make sure.
4. Put your device into Bootloader mode by pressing and holding the "Power" & "Record" buttons, and then press the Reset Button. Ooops before I forgot make sure you do a Hard Reset on your BA first.
Press and hold the "Power" & "Record" buttons, and then press the Reset Button until “Serial” shows on screen.
(Some BlueAngel shows "Serial" at the top and "V2.07" at the bottom.)
NOTE: The screen will not be backlit, so it may appear the phone is not in bootloader mode.
Look carefully.
When the USB sync cable is inserted into the phone and the computer, "Serial" will change to "USB", provided that the phone detects the connection.
5. Connect the phone to the sync cable/cradle.
7. Now you can execute the installer file. (BaUpgradeUt.exe or MaUpgradeUt.exe) You will see this window:
8. When the upgrade is completed, you must perform a Hard Reset.
When the bootscreen, aka. the colored stripes is displayed, wait more, you are booting. The welcome screen to set up your device will appear shortly ...
Click to expand...
Click to collapse
thanks but the first time i did the upgrade i started directly instaling the rom & i didn't do the previous steps in the PPC maybe tha's why, i can't no longger than the white screen is it possible??

WTF you use autodownload for ?
execute the listed commands only, then reset and then reflash the rom you want, it is that simple, and everything is covered in WIKI with a WIZARD
it is explained very well there, just don't skip any step and you will be all right

thanks xplode it worked & thank to u all

glad it helped

[JTAG] Gene JTAG 100% WORKING BY GURU SINGH BRAR

GENE J-TAG 100% WORKING FOR DEAD HTC GENE,
ALSO KNOWN AS HTC P4300/3400i
USE THIS METHOD YOUR OWN RISK
I Successfully Restore My Gene With This Method, Then I Decide To Make This Guide For Those People Who Are Paying For J-TAG.
1. Using this instruction at a certain curvature of the hand you risk permanently kill your machine at the hardware level.
2. If you are unsure of their skills, give the unit for repair technician.
3. All claims for the consequences of using this algorithm are sent to the basket without consideration!!
The technique is based on the recovery Wizard'a loaded through the JTAG bootloader executable code into RAM and transfer control to it.
As a result, you get a temporary working bootloader, and from it produces a complete firmware device (bootloader + system )
Requirement For Do This:-
1. 5 resistors of 100 ohm ¼ value (color code can be change but value has same)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2. 25-pin LPT Port (old printer cable)
3. Wires for JTAG interface MUST not be longer 20 - 25 cm.
4. A soldering Iron Skill
5. Software H-JTAG included in gene_jtag_restore.zip file.
6. Software NoIce included in gene_jtag_restore.zip file.
7. spl.nb – bin file with patched bootloader for OLD/NEW GENE in gene_jtag_restore.zip file.
8. ruu_signed.nbh – OLD/NEW Gene base ROM with IPL and patched SPL in gene_jtag_restore.zip.
9. Download The gene_jtag_restore.zip file For Later Use.
Prepare Your Phone:
First of all To dissasemble Your device look at this site
http://www.pdacenter.ru/razborka/razbor_htc_3400_gene/
Or Some Screen shot hare..
You see these TDI,TDO,TCK,TMS,nTST Pins on board called JTAG Pin reside on your phone green litghts.
Now Solder The Wire On Borad With Very Carefully.. Otherwise it Damage Your Hardware
Prepare Your LPT Cable:
Use the diagram for Creating LPT (Parallel Port) Cable For JTAG.
You Need a port on the computer called LPT Port, in its absence (for example on some laptops) may be used PCMCI LPT.
It Look Like This....
Done,, Now Connect Your Gene With This LPT Port Or You Can Say JTAG Cable
Twist the wire each other perfectly and use the tape for cover the joints...
Done...
Prepare H-JTAG Software:
1. Install And In H-JTAG.
2. Do Some Setting Like Like This...
1) In tap configuration should be this.
2) In Target Manager setting should be this.
3) In LPT JTAG Setting should be this, and nTRST checkbox must be clear. And User Define Pin Assignment Should Same As Like in The Picture.
Test H-JTAG Software is Connecting With Your Device:
Before Going Next You Must Have Full Charge Battery Of The Your Gene..
Now Put it in Your Gene And Go Next Step..
1. Set the H-JTAG.
2. We Press buttons and hold Power and Camera for 5 seconds. If the device is enabled through the power supply is activated.
3. In H-JTAG press Detect Target. Our processor with ID 0x0692602F Should be defined.
Are You Looking This..
Done. Your Half Part Is Completed...
Now Setup NoIce Software:
1. Install NoIce Software on Your PC.
2. Open NoIce Software and Setup NoIce With H-JTAG Software (Means Connect Both Software Each Other Will use Late).
3. Choose Options-Target Communications.
4. Select the RDI Interface.
5. Indicates where the H-JTAG.dll for RDI.
6. Put frequency of the processor (specify 200).
See The Picture And Do The Above Mention Steps..
7. Then click OK and close the program NoICe.
8. Done...
Now Play The Game...
1. Prepare Dead device for Restore.
2. Connect LPT JTAG Cable to LPT Port of Your PC. (Or Already Connected)
3. Start the H-jtag (the settings for the processor are given above).
4. Turn device - we press and hold the Camera button and POWER.
5. In H-jtag perform Detect Target Device - you should decide on the processor with the correct ID (0x0692602F).
You See This..
6. Run NoICe if everything is normal and all right-minded above program should be the address of 0000 and you see the code ARM.
7. If you have NEW GENE create a folder NEWGENE in c:\ (root) without any space example C:\NEWGENE . And copy spl.nb & ruu_signed.nbh file from (for new Gene (SN - HT8x)) folder which include in gene_jtag_restore.zip to in this NEWGENE Folder and also copy the full RomUpdateUtility in this folder.
OR
8. If you have OLD GENE create a folder OLDGENE in c:\ (root) without any space exmpale C:\OLDGENE . And copy spl.nb & ruu_signed.nbh file from (for new Gene (SN - HT7x)) folder which include in gene_jtag_restore.zip to in this OLDGENE Folder and also copy the full RomUpdateUtility in this folder.
Next, consider the following illustration, And Use The Step Below The Picture..
1. Necessarily ..first we put a tick on Load as binary image.
2. We Specify the address of loading in RAM 10000000 (Check it Correctly).
3. We Choose a file bootloader for loading spl.nb form Folder.
4. Choose This File Form,, If Your Gene is New Use NEWGENE Folder.
Or
5. Choose This File Form,, If Your Gene is OLD Use OLDGENE Folder.
6. We press Ok and we see progress a bar of loading (it is necessary to wait some time).
7. As soon as its filled with the file we choose item of menu View and choose submenu Disassemble at...
8. Address necessary to be specified 10000000,
9. We press Ok and we see code ARM - if aall ij well and the file is loaded , then the first command should be EA0003FE.
6. Press And Hold Camera Button and Press on the program menu RUN and to submenu Go FROM...
7. We Specify 10000000 in address and press Ok....
8. Device must be run in mode bootloader.
9. If Your Device Boot In Bootloader Mode So, Now Camera And Power Button can be released..
Now Flash The Device With Boot Rom
1. Now We connect to usb and it is flashed with ruu_signed.nbh file from Folder OLDGENE/NEWGENE depend on Your Gene Model..
2. It is possible remove Jtag and to collect Your phone.
3. Further we flash with a good ROM(cooked) and no stock ROM please.. it’ll kill it again...
DOWNLOAD : - gene_jtag_restore.zip
Good Bye.....

Thats a Step-By-Step Guide on JTAG for New bees
Hi Guru,
You have done an awesome compilation. You have really made a step-by-step guide for JTAG for the new bees. I like to thank you for your valuable work. And also like to thank the members of XDA-Developers -
Orefkov, BesFen, Krazy_about_technology, Addicted2xda, Vaibhav_batra_the_techguy, haree, karan999, sumeet922, gurusinghbrar and so on...
for their valuable work on HTC Gene - JTAG Recovery & ROM Development.
Last but not the least... Keep it up, Guru. I give you Lots of Applause for this Post.
Moderators can you make this post Sticky... Its a request, Please.Thanks to XDA-Developers for giving such a team support.

Awesome !!!!!!!!!!!!!!!! great work.thanks for sharing.

thanks for sharing

Help us to start dead p3400i
please tell me location of Bootloader file, you have mentioned (sspl-s_wizard.nb) in bitmap.. i am unable to find bootloader.. for loading.

Thanx for solution........but accidentally my Phone's TDI pin has Damaged..........pls tell me any solution of tracing or clone of the TDI pin.

Help please!!!!
I have bricked my HTC Gene While flashing it with a official rom
I went through your Step by step instruction for unbricking with J TAG
but the main problem i use a netbook and it does not have the port for printer
i have even sent the phone for service and it was useless
this phone is very dear to me and cant see it just lying . please suggest a alternative method im also willing to send the phone to you if you will help me unbrick it

gurusinghbrar said:
GENE J-TAG 100% WORKING FOR DEAD HTC GENE,
ALSO KNOWN AS HTC P4300/3400i
USE THIS METHOD YOUR OWN RISK
I Successfully Restore My Gene With This Method, Then I Decide To Make This Guide For Those People Who Are Paying For J-TAG.
1. Using this instruction at a certain curvature of the hand you risk permanently kill your machine at the hardware level.
2. If you are unsure of their skills, give the unit for repair technician.
3. All claims for the consequences of using this algorithm are sent to the basket without consideration!!
The technique is based on the recovery Wizard'a loaded through the JTAG bootloader executable code into RAM and transfer control to it.
As a result, you get a temporary working bootloader, and from it produces a complete firmware device (bootloader + system )
Requirement For Do This:-
1. 5 resistors of 100 ohm ¼ value (color code can be change but value has same)
2. 25-pin LPT Port (old printer cable)
3. Wires for JTAG interface MUST not be longer 20 - 25 cm.
4. A soldering Iron Skill
5. Software H-JTAG included in gene_jtag_restore.zip file.
6. Software NoIce included in gene_jtag_restore.zip file.
7. spl.nb – bin file with patched bootloader for OLD/NEW GENE in gene_jtag_restore.zip file.
8. ruu_signed.nbh – OLD/NEW Gene base ROM with IPL and patched SPL in gene_jtag_restore.zip.
9. Download The gene_jtag_restore.zip file For Later Use.
Prepare Your Phone:
First of all To dissasemble Your device look at this site
http://www.pdacenter.ru/razborka/razbor_htc_3400_gene/
Or Some Screen shot hare..
You see these TDI,TDO,TCK,TMS,nTST Pins on board called JTAG Pin reside on your phone green litghts.
Now Solder The Wire On Borad With Very Carefully.. Otherwise it Damage Your Hardware
Prepare Your LPT Cable:
Use the diagram for Creating LPT (Parallel Port) Cable For JTAG.
You Need a port on the computer called LPT Port, in its absence (for example on some laptops) may be used PCMCI LPT.
It Look Like This....
Done,, Now Connect Your Gene With This LPT Port Or You Can Say JTAG Cable
Twist the wire each other perfectly and use the tape for cover the joints...
Done...
Prepare H-JTAG Software:
1. Install And In H-JTAG.
2. Do Some Setting Like Like This...
1) In tap configuration should be this.
2) In Target Manager setting should be this.
3) In LPT JTAG Setting should be this, and nTRST checkbox must be clear. And User Define Pin Assignment Should Same As Like in The Picture.
Test H-JTAG Software is Connecting With Your Device:
Before Going Next You Must Have Full Charge Battery Of The Your Gene..
Now Put it in Your Gene And Go Next Step..
1. Set the H-JTAG.
2. We Press buttons and hold Power and Camera for 5 seconds. If the device is enabled through the power supply is activated.
3. In H-JTAG press Detect Target. Our processor with ID 0x0692602F Should be defined.
Are You Looking This..
Done. Your Half Part Is Completed...
Now Setup NoIce Software:
1. Install NoIce Software on Your PC.
2. Open NoIce Software and Setup NoIce With H-JTAG Software (Means Connect Both Software Each Other Will use Late).
3. Choose Options-Target Communications.
4. Select the RDI Interface.
5. Indicates where the H-JTAG.dll for RDI.
6. Put frequency of the processor (specify 200).
See The Picture And Do The Above Mention Steps..
7. Then click OK and close the program NoICe.
8. Done...
Now Play The Game...
1. Prepare Dead device for Restore.
2. Connect LPT JTAG Cable to LPT Port of Your PC. (Or Already Connected)
3. Start the H-jtag (the settings for the processor are given above).
4. Turn device - we press and hold the Camera button and POWER.
5. In H-jtag perform Detect Target Device - you should decide on the processor with the correct ID (0x0692602F).
You See This..
6. Run NoICe if everything is normal and all right-minded above program should be the address of 0000 and you see the code ARM.
7. If you have NEW GENE create a folder NEWGENE in c:\ (root) without any space example C:\NEWGENE . And copy spl.nb & ruu_signed.nbh file from (for new Gene (SN - HT8x)) folder which include in gene_jtag_restore.zip to in this NEWGENE Folder and also copy the full RomUpdateUtility in this folder.
OR
8. If you have OLD GENE create a folder OLDGENE in c:\ (root) without any space exmpale C:\OLDGENE . And copy spl.nb & ruu_signed.nbh file from (for new Gene (SN - HT7x)) folder which include in gene_jtag_restore.zip to in this OLDGENE Folder and also copy the full RomUpdateUtility in this folder.
Next, consider the following illustration, And Use The Step Below The Picture..
1. Necessarily ..first we put a tick on Load as binary image.
2. We Specify the address of loading in RAM 10000000 (Check it Correctly).
3. We Choose a file bootloader for loading spl.nb form Folder.
4. Choose This File Form,, If Your Gene is New Use NEWGENE Folder.
Or
5. Choose This File Form,, If Your Gene is OLD Use OLDGENE Folder.
6. We press Ok and we see progress a bar of loading (it is necessary to wait some time).
7. As soon as its filled with the file we choose item of menu View and choose submenu Disassemble at...
8. Address necessary to be specified 10000000,
9. We press Ok and we see code ARM - if aall ij well and the file is loaded , then the first command should be EA0003FE.
6. Press And Hold Camera Button and Press on the program menu RUN and to submenu Go FROM...
7. We Specify 10000000 in address and press Ok....
8. Device must be run in mode bootloader.
9. If Your Device Boot In Bootloader Mode So, Now Camera And Power Button can be released..
Now Flash The Device With Boot Rom
1. Now We connect to usb and it is flashed with ruu_signed.nbh file from Folder OLDGENE/NEWGENE depend on Your Gene Model..
2. It is possible remove Jtag and to collect Your phone.
3. Further we flash with a good ROM(cooked) and no stock ROM please.. it’ll kill it again...
DOWNLOAD : - gene_jtag_restore.zip
Good Bye.....
Click to expand...
Click to collapse
dude m bit confused in connection of wire in lpt port the diagram image here in this page is different n the diagram image is different in the gene_Jtag_restore.rar ,so plz help me which connect i should do for my restore process,reply.
thank in advance

Haha
lol nobody gives a fukc
Btw is it like something usb jigg !

THANKS
Thanks this will help me with my dads old phone.

x8 bricked

Hey, just got my x8 Briked, stuck at the SE boot logo.
Can't go to the xrecovery menu ... help ?!
ROM used was jerpelea's v003, got the " SD safe to remove " reboot then stuck.

Reinstall system with SEUS or PC Companion or with FlashTool

Pc Companion cannot connect to my phone.
I'll try SEUS ( downloading version 2.7 atm ).
If it fails to, let's go try FlashTool then, it's available from jerpelea's ROM packages, right ?
Thank for reply !

Just repair/update as dbts25 said, or try again to get in xrecover menu, maybe it start ...
...if your phone restart, pc cant make a connection. U have to start your phone from flash,
Connect the cable, open your phone and hold down back button to connect it...
Try it!

Yes it can be there. I don't download his ROM yet so I don't know

PC Companion = Fail
SEUS = Fail
FlashTool = Fail
Edit : Any other solution or links for your FlashTool & SEUS versions which I might try

First of all, do not panic (i say that because i was in panic myself the first time i bricked my phone).
I suggest you to install the stock rom from pc companion (then install what ever you want). You will LOOSE ALL your data (exept the ones in your SDcard), but it's better that a bricked phone
PC companion will work, follow the steps:
1. Go to "Support Zone" (in Pc Companion)
2. Click "Start" (without to connect the phone)
3. A window will pop up, click the "Repair phone" link
4. Click "continue"
ATTENTION: Somewhere here the program will ask you to choose you phone, i can't tell when because i have choose mine the first time i did it. After this it will ask you to connect it pressing the "Back" button.
5. A window will pop up to inform you somehow that you will lost you data, ckeck the box and click "next"
6. The PC Companion will download the final version of your stock rom, just wait... and then it will install it.
(the phone will connect throught flash mode)
P.S.:This will work, that's how i fixed my X8 when i had the same problem...
I hope that i helped you
EDIT: Write to jerpelea about the bug so he/she can fix it.

GreatApo said:
First of all, do not panic (i say that because i was in panic myself the first time i bricked my phone).
I suggest you to install the stock rom from pc companion (then install what ever you want). You will LOOSE ALL your data (exept the ones in your SDcard), but it's better that a bricked phone
PC companion will work, follow the steps:
1. Go to "Support Zone" (in Pc Companion)
2. Click "Start" (without to connect the phone)
3. A window will pop up, click the "Repair phone" link
4. Click "continue"
ATTENTION: Somewhere here the program will ask you to choose you phone, i can't tell when because i have choose mine the first time i did it. After this it will ask you to connect it pressing the "Back" button.
5. A window will pop up to inform you somehow that you will lost you data, ckeck the box and click "next"
6. The PC Companion will download the final version of your stock rom, just wait... and then it will install it.
(the phone will connect throught flash mode)
P.S.:This will work, that's how i fixed my X8 when i had the same problem...
I hope that i helped you
EDIT: Write to jerpelea about the bug so he/she can fix it.
Click to expand...
Click to collapse
Ok, I think I know why I can't repair..
Take a look at this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
( can't give you the full link because I'm new, delete the space between, sry for the inconvenience ).
It seems like my computer is missing the SEMC USB Flash drivers.
I get them from the net but the .inf driver file wont install..

ok, let's see... 2 suggestions (try second first)
1. First of all try to download and install "Gordons Gate". It installs the drivers BUT i was using it for my old phone (SE s500i, it's not a smartphone). I do not know if it will works...
2. Else, I can provide you my "Drivers" folder from my PC Companion folder. Copy your Drivers folder to desktop first (to have a back up), and then extrack my zip file in the "C:\Program Files\Sony Ericsson\Sony Ericsson PC Companion" or where ever you have your PC companion installed. (i think now it will not ask you to choose you phone)
Drivers.zip (download from mediafire)
I asume you have windows. I wish i works...

Thank you sir !
Solved my drivers problem with an other version of Gordon's Gate !
I had the 2.2.0.10 > uninstalled then reinstalled the 2.2.0.5 then worked fine !
Now I can repair my phone !
Thanks again ! <3

alextothex said:
Thank you sir !
Solved my drivers problem with an other version of Gordon's Gate !
I had the 2.2.0.10 > uninstalled then reinstalled the 2.2.0.5 then worked fine !
Now I can repair my phone !
Thanks again ! <3
Click to expand...
Click to collapse
Do not call me sir...i am only 18 .
So "Gordon's Gate" is still working... nice...
EDIT: I use v2.2.0.0, it works too

Flash TA by omnius HOw you wat i can upload my TA backup

zxc79 said:
Flash TA by omnius HOw you wat i can upload my TA backup
Click to expand...
Click to collapse
Why would he flash TA? It's not smart idea because Omnius can't recalculate sec. zone so he would end up with REALLY bricked phone...
Sent from my X8, so sorry for gramatical inaccuracy

alextothex said:
Thank you sir !
Solved my drivers problem with an other version of Gordon's Gate !
I had the 2.2.0.10 > uninstalled then reinstalled the 2.2.0.5 then worked fine !
Now I can repair my phone !
Thanks again ! <3
Click to expand...
Click to collapse
OOT: i think greatapo deserves to get thanks.

Hi there, I also bricked my x8. I messed up with the build.prop file and now i think PcCompanion "sees" it as an x10 device.It doesn't go any further than Sony Ericcson logo and I have to remove the battery to make it start.
I tried the above method of restoring it but SEUS says there isn't any software available.
SEUS just checks and then tells me there are no updates available.
Any ideas?

hazopoulis said:
Hi there, I also bricked my x8. I messed up with the build.prop file and now i think PcCompanion "sees" it as an x10 device.It doesn't go any further than Sony Ericcson logo and I have to remove the battery to make it start.
I tried the above method of restoring it but SEUS says there isn't any software available.
SEUS just checks and then tells me there are no updates available.
Any ideas?
Click to expand...
Click to collapse
Try the repair solution i have post above. Go to update with pc companion but do not connect your phone to the pc, a window will pop up. Click repair and folow the instuctions...
Yours, GreatApo
(Sent from my Xperia X8)

Thanks for the reply GreatApo.
When I try the repair solution i get the message: "there is no software available for your phone yet.Please try again later". As I recall now, I changed the build.prop with one of X10 device and when I recovered the backup something went wrong (maybe i erased it?!)
So now neither SEUS nor X10FlashTool can do anything. Is there a way to restore build.prop?
edit: I just had another idea. Is there any way to mesh up the phone even more so it doesn't see it as an up-to-date x10 and DO the repair?
Sony Ericsson doesn't really have a flashing tool, does it?

It's my solution.
1. Download flashtool with orginal rom 2.1 and drivers from rapidshare.com/files/451848208/flashtool.rar
2. Unpack
3. Install drivers if U need
4. Open X10flash.bat
5. choose your operating system
6. connect phone to flash mode
7. on PC click any key
8. wait for finish flash
9. enjoy your working phone

hazopoulis said:
When I try the repair solution i get the message: "there is no software available for your phone yet.Please try again later".
Click to expand...
Click to collapse
I thing that repair does not search for an update, it just download the latest official rom. try the other people suggestions... there must be a solution.

Again, thank you for the replies.
I tried flashtool through X10flash.bat but I couldn''t get past the selection of OS. Is there a difference with the GUI version of flashtool? Using GUi version, everytime it started flashing it gave me an error and never finished flashing.
I also thought that repair from Pc Companion would and SHOULD do the job but as it turns out it isn't a repair tool after all.
Anyway, I finally sent it to service 'cause I need it soon.
Bottom line: Be careful when messing with build.prop ! : )

How To Reinstall Windows Mobile on Hp Hw6915

Hi Guys
Can someone tell me how to reinstall windows mobile on hp hw6915?
I realy need your help. In this 'xda-developers' i not find any info about this, so i decided create this post for hp hw6915. Can anyone help me?

ExodiaXlr7 said:
Hi Guys
Can someone tell me how to reinstall windows mobile on hp hw6915?
I realy need your help. In this 'xda-developers' i not find any info about this, so i decided create this post for hp hw6915. Can anyone help me?
Click to expand...
Click to collapse
just follow the tutorial on this thread ~ http://forum.xda-developers.com/showpost.php?p=6391896&postcount=1

If you just want reset to default factory settings, you must press all together: power + green button + red button + reset with stylus (bothom of the phone).
If you want to change language of hw6915 you must reflash with ROM update utility, but make sure there are no rom update files for radio (RadioOS.nbf RadioFS.nbf) as they could brick GSM part of the phone.

Thank you for this link about how to reinstall os, but still i dont understand anythink in this tutorial about os. Can someone make a video turotial?

If you are following that tutorial be aware! Do not "task 28 55aa" with mtty - that will cause change of the device Product ID and you will not be able to use official HP upgrade tools anymore.
Why it is that you want to reinstall rom? Does hard reset not working?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

I try to do hard reset, but stil i have same problems with this hp hw6915. Problems is: i cant remove some programs, windows is flickering lines. memory to low, i try increase memory by removing some programs but it does not work and t.t.

It is true that default software on hw6915 is slow - you should use memorycard for software to get better results.
If you are really willing to try to reinstall, I can only give you this one link
multiupload com /UTYDNBZ145
Click to expand...
Click to collapse
but use it at your own risk - it is possible that results will be the same.

What you think about this?
How to write custom rom WM on hp iPAQ hw6915.
------------------------------------------------
1.Connect your device to PC by ActiveSync (download it from microsoft page)
2.Run "Command prompt" from folder "SPL vG.39" (if using vista/7 RUN AS ADMINISTRATOR)
3.Enter this command: pdocwrite spl -n0 -b 0x20000 0 0x80000 (WAIT UNTIL IT FINISHES).
This command replaces a file in the ROM which allows you to flash ''non-original roms'',
basically software CID unlocking which allows flashing of ''cooked roms''
4.You will get a warning on your hp regarding a dll file (itsutils.dll), PRESS YES
5.Put your device in bootloader mode. (hold the two selection buttons next to the joystick
and shortly tap the reset button with your stylus)
6.Open activesync, go to connections and untick "Allow USB connections"
7.Extract "Sable_G4_1.21_UK_ROM.rar" and run "Sable_RUU.exe"
8.Press on the big "Upgrade" button
9.There will be a progress bar, when it's done it should say something like "Update finished !!"
10.Go back to activesync and re-tick "Allow USB connections".

The manual you quoted is correct for case if you want to upgrade to non-stock rom like some custom made Windows Mobile 6 rom (if you already found one), but you must ensure that there are no RadioOS.nbf and RadioFS.nbf in the folder where Sable_RUU.exe resides or else you might ruin your gsm.
If you just want to reinstall Windows Mobile 5 then there is no need for "pdocwrite spl -n0 -b 0x20000 0 0x80000" (as it is only needed to allow non-stock rom flashing).

So in order to do wm5 reinstall i just must follow my writen instruction but in this case i need skip 2, 3 and 4 steps, and start from 5 step? (of course first i need plug my device to PC by ActiveSync). ?
What is Radio?
In Sable_RUU.exe i found such files: CEOS.nbf, EnterBL, GetDeviceData and Sable_RUU.
In SPL vG.39 folder i found such files: Command Prompt, itsutils.dll, libeay32.dll, msvcr71.dll, pdocwrite und spl.

Can someone help me!
I was doing this update tranquility, I have a hp ipaq 6915 and use the windows7.
I did the first part of this
process, which installs the. dll. All right so far. I was
for the second stage and the program Sable RUU erased my
WM5, ok, so that after this process began to windows
search for the driver usb ipaq, of course, was
disconnected, then this error appeared Client_GetOSVer fail !! Error : 501.
Now I'm without my operating system.
And what I do now?

From what I undestood from your one before last post (the files included gave me idea) you have downloaded wm6 update utilities and rom. So in this case you must take all the steps.
If you want wm5 then you must download link http://multiupload.com/UTYDNBZ145 and just plug device to usb (before that put it in the bootloader mode: by pressing power button + button next to green + button next to red + reset with stylus), wait to connect and then run Sable_RUU.exe
About your question... Radio rom files are sometimes included in distributed upgrade files, so you must ensure they are deleted from the folder before start flashing. These files are usually responsible - there already been two cases to my devices - for killing the GSM chip data, so you can not use your device for phone calls anymore lets sey it is very bad scenario, so I am warning you to not to break your device!
Seems like you are left without any os at this very moment, so you should now install wm5 again and if you then want to upgrade wm6 repeat all the steps (including pdocwrite command).
If you are just stuck in bootloader google for UNI_ExitBootloader.exe

So bootloader mode is when my hp hw6915 screen show this: Serial Hp G.39 or when hp hw6915 screen is totaly off? When i try use UNI_ExitBootloader.exe it does not work because it say: Error - Cannot open USB port. So i try again and again but this time i disable ActiveSync... but still in not work. So i try an alternative method. I download Virtual box, then i install win xp, download Sable_G3_DEVICE_ONLY_hw6915-1.21uk ant try run. IT WORKS
THNAKS YOU JOGIJS ;-) Now i need your help to update my device from wm5 to wm6 o greater.

First of all - there are no official hp releases upgrade to wm6 or greater, but as I think you found one of unofficial upgrades to wm6 made by hackers.
Then - Sable_G3_DEVICE_ONLY_hw6915-1.21uk is the same as in my link http://multiupload.com/UTYDNBZ145 only difference that my file is without the radio roms.
About upgrading to wm6:
As I said before - now you need to follow instructions you posted before and do all the steps to upgrade to wm6 (remember about my radio warning! ) as you have found correct manual for wm6 upgrading.
If you understand russian you could try this wm6 upgrade - http://www.multiupload.com/QTP68IW7AM
About your question:
You are in bootloader mode when there are serial/USB + hp logo + G.39 on the screen.
If you have USB connectivity problems on w7 32bit, use this driver - http://www.multiupload.com/IE15IM9DHT Always check your device manager to ensure your Sable device is recognized!

One more question ;-) In my Hp Hw6915 i install wm for G3 chip, but i noticed that mine is G4 chip. So in future this can cause problems on mine device?

I think it is just a mislabel as mine current device is also G4 (as seen on hp's asset viewer) and it does not run into any problems by flashing OS
Maybe confusion is set by bootloader's title "G.39"... I think so, but I am not sure, what caused this for true.
Despite all - these roms and utilities worked for me (except for radio roms of course).

same problem
hello i have hp ipaq hw6915 in norvegian language i try to use your tutorial and now appear bootscreen (USB+Logo+vG.39) how can i do for resolve my problem because i try to HARD RESET and appear same USB+Logo+vG.39, you can reupload your application to other website?

under the boot screen it's .39. it's fine.
what do you want to do with your ipaq? still using wm 5 or wm 6?
I can give you a link on xda which has all the explanation on how to upgrade to wm 6 but if you want to stay on wm5, I suggest you do a hard reset. if you say after hard reset you still cannot remove program, I am quite confused. Because hard reset really put you in a basic start where everything is cleared.
try hard reset one more time...
if you still have problem, post again here... I will try to help you as much as I can...

i try HARD RESET 1000 times appear same USB(or SERIAL if is not connect on pc)+Logo+vG.39, i want to try WM6, if you can help me pls offer a solution.

download this file, unpack and run Sable_RUU
http://www.4shared.com/rar/NokqR8Q2/121_UK.html
worked fine for my hp 6915 with Danish rom - I have English now
IT MIGHT HELP YOU

Lumia 520 - Unable to find a bootable option

A friend has asked me to look at this Nokia Lumia 520, apparently it turned on one day and displayed this error message "unable to find a bootable option. Press any key to shutdown"
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Nokia Software Update for Retial recognises the phone and says software can be installed:
This downloads fine and starts the install process, however always fails with the message "phone not supported by nokia software updater retail"
I have also tried using NaviFirm+, searching for the product code 059S3T5 which lets me download the RM914_3058.50000.1425.0006_RETAIL_eu_euro1_327_06_452364_prd_signed firmware.
However i'm unable to flash this with the Nokia Care Suite, it states: 0xFA001106: Signature check of FFU file fails. Reason(s): The FFU file is not correctly signed or not signed for this device.
Has anyone got any suggestions on what else i can try to flash this firmware? or to try fix the phone?
I was following the tutorial here Flash/unbrand Lumia devices thinking if the firmware was re flashed all would be fine.
Cheers for any advice

Have you try with this
http://www.microsoft.com/en-us/mobile/support/faq/?action=singleTopic&topic=FA142987

Thanks for the suggestion, I have tried that, it will download the firmware too, however fail before flashing it stating the device is not supported.

InsaneNutter said:
Thanks for the suggestion, I have tried that, it will download the firmware too, however fail before flashing it stating the device is not supported.
Click to expand...
Click to collapse
I think win partition is crash. (like memory damage/corruption)
Hardware related problems.

InsaneNutter said:
A friend has asked me to look at this Nokia Lumia 520, apparently it turned on one day and displayed this error message "unable to find a bootable option. Press any key to shutdown"
Nokia Software Update for Retial recognises the phone and says software can be installed:
This downloads fine and starts the install process, however always fails with the message "phone not supported by nokia software updater retail"
I have also tried using NaviFirm+, searching for the product code 059S3T5 which lets me download the RM914_3058.50000.1425.0006_RETAIL_eu_euro1_327_06_452364_prd_signed firmware.
However i'm unable to flash this with the Nokia Care Suite, it states: 0xFA001106: Signature check of FFU file fails. Reason(s): The FFU file is not correctly signed or not signed for this device.
Has anyone got any suggestions on what else i can try to flash this firmware? or to try fix the phone?
I was following the tutorial here Flash/unbrand Lumia devices thinking if the firmware was re flashed all would be fine.
Cheers for any advice
Click to expand...
Click to collapse
Hi,
Have you sorted your phone out yet?

BruceKDallas said:
Hi,
Have you sorted your phone out yet?
Click to expand...
Click to collapse
Hi,
Nope i could never fix the phone, I spent loads of time messing about with it however think it was a hardware related problem.
I've given it back to my friend and shes since got a new phone.

I am into the same situation... NOKIA 520 RM-914 Code 059S7H0
"ERROR: Unable to find a bootable option. Press any key to shut down". Any button I push, the phone is going in bootloop ending with this ERROR...
I have tryed first with Windows Device Recovery Tool (WDRT) 3.1.4 to repair it, but no success...
In WDRT my Lumia is not detected automatically, so i must choose manually device manufacturer. To be detected I must restart the Lumia when DWRT is trying to detect it.
The Phone is detected as LUMIA phone, firmware version: unknown, Software available on server: 3058.50000.1425.003.
When I try to install the software after I download the package, the result is:
"Operation ended with failure. The software is not correctly signed or not signed for this device."
The NOKIA driver is seen as NOKIA BOOTMGR.
Then I've search on the internet about this problem and I've found this thread.
I tried the advanced mode with thor2.exe, I downloaded manually the firmware for my device Lumia 520, RM-914, Code 059S7H0
I opened Command Prompt as administrator, then used the command:
cd c:\Program Files (x86)\Microsoft Care Suite\Windows Device Recovery Tool\
I used the command line to extract gtp0.bin from ffu image:
thor2 -mode ffureader -ffufile "C:\rm-914\RM914_3058.50000.1425.0003_RETAIL_eu_hungary_422_03_447211_prd_signed.ffu"
The result was 2 files, gpt0.bin and GPT1.bin. I renamed gpt0.bin as msimage.mbn.
RKH of the device is:
RKH of SBL1: F771E62AF89994064F77CD3BC16829503BDF9A3D506D3FACECAEF3F808C868FD
RKH of UEFI: F771E62AF89994064F77CD3BC16829503BDF9A3D506D3FACECAEF3F808C868FD
I've downloaded the hex file for my Lumia RM-914 to have the 2 files HEX.hex and msimage.mbn for the command line:
thor2 -mode emergency -hexfile "C:\TEMP\HEX.hex" -mbnfile "C:\TEMP\msimage.mbn" -orig_gpt
THOR2 1.8.2.18
Built for Windows @ 13:36:46 Jun 16 2015
Thor2 is running on Windows of version 6.1
thor2 -mode emergency -hexfile C:\TEMP\HEX.hex -mbnfig_gpt
Process started Sun Dec 06 23:12:08 2015
Debugging enabled for emergency
Initiating emergency download
Operation took about 10.00 seconds.
THOR2_ERROR_CONNECTION_NOT_FOUND
THOR2 1.8.2.18 exited with error code 84000 (0x14820)
The Phone is still in NOKIA BOOTMGR mode...
If I try to disconnect the phone and restart, it goes into the the same message:
"ERROR: Unable to find a bootable option. Press any key to shut down", not showing me the RED screen like it should be.
If I go into the next step for flashing the device with the command line:
thor2.exe -mode vpl -maxtransfersizekb 1 -vplfile "C:\RM-914\RM914_059S7H0_3058.50000.1425.0003_037.vpl"
the screen changes into a big NOKIA logo, the driver goes from NOKIA BOOTMGR into NOKIA FLASH...
Thor2 is running on Windows of version 6.1
thor2.exe -mode vpl -maxtransfersizekb 1 -vplfile C:\RM-914\RM914_059S7H0_3058.5
0000.1425.0003_037.vpl
Process started Sun Dec 06 23:22:20 2015
Logging to file C:\Users\Marta\AppData\Local\Temp\thor2_win_20151206232220_Threa
dId-3864.log
Parsing VPL file C:\RM-914\RM914_059S7H0_3058.50000.1425.0003_037.vpl
Successfully parsed VPL
Flashing .ffu file RM914_3058.50000.1425.0003_RETAIL_eu_hungary_422_03_447211_pr
d_signed.ffu (SW version 3058.50000.1425.0003)
Debugging enabled for uefiflash
Initiating FFU flash operation
WinUSB in use.
isDeviceInNcsdMode
isDeviceInNcsdMode is false
Device mode 6 Uefi mode
[THOR2_flash_state] Pre-programming operations
Disable timeouts
Get flashing parameters
Lumia Boot Manager detected
Check status of battery
State of charge 8, charging current 282
Protocol version 1.1 Implementation version 1.16
Detecting UEFI responder
HELLO success
Lumia Boot Manager detected
Check status of battery
State of charge 8, charging current 266
Protocol version 1.1 Implementation version 1.16
Booting to FlashApp
Reboot to FlashApp command sent successfully.
DetachFrom connection
Verifying that device is online
Device is online
Detecting UEFI responder
HELLO success
Lumia Flash detected
Protocol version 1.15 Implementation version 1.28
Disable timeouts
Get flashing parameters
Lumia Flash detected
Protocol version 1.15 Implementation version 1.28
Size of one transfer is 2363392
Size of buffer is 2359296
Number of eMMC sectors: 15269888
Platform ID of device: Nokia.MSM8227.P6036.1.2
Async protocol version: 01
Security info:
Platform secure boot enabled
Secure FFU enabled
JTAG eFuse blown
RDC not found
Authentication not done
UEFI secure boot enabled
SHK enabled
Device supports FFU protocols: 0019
[THOR2_flash_state] Device programming started
Using secure flash method
CoreProgrammer version 2015.06.10.001.
Start programming signed ffu file C:\RM-914\RM914_3058.50000.1425.0003_RETAIL_eu
_hungary_422_03_447211_prd_signed.ffu
FfuReader version is 2015061501
Send FlashApp write parameter: 0x4d544f00
Perform handshake with UEFI...
Flash app: Protocol Version 1.15 Implementation Version 1.28
DevicePlatformInfo: Nokia.MSM8227.P6036.1.2
Unknown sub block detected. Skip...
Unknown sub block detected. Skip...
Supported protocol versions bitmap is 19
Secure FFU sync version 1 supported.
Secure FFU async version 1 supported.
Secure FFU async version 3 supported.
Get CID of the device...
Get EMMC size of the device...
Emmc size in sectors: 15269888
CID: Samsung, Size 7456 MB
Start charging...
Requested write param 0x43485247 is not supported by this flash app version.
Start charging... DONE. Status = 0
Unable to send ECHO REQ or ECHO REQ not supported
Get security Status...
Security Status:
Platform secure boot is enabled.
Secure eFUSE is enabled.
JTAG is disabled.
RDC is missing from the device.
Authentication is not done.
UEFI secure boot is enabled.
Secondary HW key exists.
Get RKH of the device...
RKH of the device is F771E62AF89994064F77CD3BC16829503BDF9A3D506D3FACECAEF3F808C
868FD
Get ISSW Version...
Get ISSW Version, SKIPPED!
Get system memory size...
Size of system mem: 524288 KB
Read antitheft status...
Requested read param 0x41545250 is not supported by this flash app version.
Send backup to RAM req...
Clearing the backup GPT...SKIPPED!
Successfully parsed FFU file. Header size: 0x000e0000, Payload size: 0x000000006
2900000, Chunk size: 0x00020000, Header offset: 0x00000000, Payload offset: 0x00
000000000e0000
RKH match between device and FFU file!
Option: Skip CRC32 check in use
Start sending header data...
FlashApp returned reported error in SecureFlashResp!
Status: 0x1106, Specifier: 0x8000000E
FA_ERR_FFU_SEC_HDR_VALIDATION_FAIL
Send of FFU header failed!
[IN] programSecureFfuFile. Closing C:\RM-914\RM914_3058.50000.1425.0003_RETAIL_e
u_hungary_422_03_447211_prd_signed.ffu
programming operation failed!
0xFA001106: Signature check of FFU file fails. Reason(s): The FFU file is not co
rrectly signed or not signed for this device.
Operation took about 3.00 seconds.
THOR2_ERROR_FA_SIGNATURE_FAIL
THOR2 1.8.2.18 exited with error code -100658938 (0xFA001106)
Here, after this step, if the flash is 100% succesful, the screen must change in Green,
mine finished with the same error: "The FFU file is not correctly signed or not signed for this device..."
I guess the most of us are into the same situation, I can't make the device to skip the signature check... Any sugestions?

have you jtag?

As far as I read, JTAG is a toolbox for repairing Phones which have the same problem, but what we are trying to do is without this toolbox, we have a dead phone at home. Microsoft said is a hardware failure and they must change complete motherboard, but with Jtag Toolbox can be repaired without change anything, just a complete writing of the bootloader and software. I don't want to buy the toolbox just to repair my Lumia 520, I don't need it, I'm just a home user not a repairing company...

melhisedec said:
As far as I read, JTAG is a toolbox for repairing Phones which have the same problem, but what we are trying to do is without this toolbox, we have a dead phone at home. Microsoft said is a hardware failure and they must change complete motherboard, but with Jtag Toolbox can be repaired without change anything, just a complete writing of the bootloader and software. I don't want to buy the toolbox just to repair my Lumia 520, I don't need it, I'm just a home user not a repairing company...
Click to expand...
Click to collapse
are you should to find testpoint for qcom9008. and flashing phone.

Mine was running everything give I install windows 10 just give the battery does not know dai was appearing this message (Erro Unable to find a bootable option error. Press any key to shut down,) Lumia 925 Brazil
---------- Post added at 03:41 AM ---------- Previous post was at 03:36 AM ----------
Mine was running everything give I install windows 10 just give the battery does not know dai was appearing this message (Erro Unable to find a bootable option error. Press any key to shut down)

Usually, is the main problem with Lumia Software update and stupid engineers from Microsoft does not fix it...

you deleted header partition, and lumia don't power on. help you only jtag.

I didn't know anything about this problem of almost any Lumia device until my phone has done the automatic software update from Win8 to 8.1 or 10, I don't know which one... And the the phone restarted with this stupid problem:
"ERROR: Unable to find a bootable option. Press any key to shut down"...
I have one week of searching over the internet to fix this but i couldn't make it...
If i can remove or unlock the bootloader, maybe I can force the phone to be Flashed with WDRT 1.34 and no more error:
"The FFU file is not correctly signed or not signed for this device."

melhisedec said:
I
Click to expand...
Click to collapse
Only you can help the programmer and all) nokia, wpinternals not flashing it. pins or seek to enter the 9008 regime (disassembly required).
partition table got off
i know this problems on my lumia 720(1 motheboard- After the firmware is not those files, 2 motherboards- After stitched sbl3 not true - died).
jtag helped to you, and me.

InsaneNutter said:
Hi,
Nope i could never fix the phone, I spent loads of time messing about with it however think it was a hardware related problem.
I've given it back to my friend and shes since got a new phone.
Click to expand...
Click to collapse
Cool. I had the same issue and many other issues with my 520. I have a very cool way of fixing this and all other issues if you struggle to start the phone up. If you are interested, let me know and I will explain to you. Very easy and process takes about 5 minutes.
Cheers

BruceKDallas said:
Cool. I had the same issue and many other issues with my 520. I have a very cool way of fixing this and all other issues if you struggle to start the phone up. If you are interested, let me know and I will explain to you. Very easy and process takes about 5 minutes.
Cheers
Click to expand...
Click to collapse
How did you do ?

melhisedec said:
As far as I read, JTAG is a toolbox for repairing Phones which have the same problem, but what we are trying to do is without this toolbox, we have a dead phone at home. Microsoft said is a hardware failure and they must change complete motherboard, but with Jtag Toolbox can be repaired without change anything, just a complete writing of the bootloader and software. I don't want to buy the toolbox just to repair my Lumia 520, I don't need it, I'm just a home user not a repairing company...
Click to expand...
Click to collapse
Did you follow http://forum.xda-developers.com/showthread.php?t=2515453 correctly?

InsaneNutter said:
A friend has asked me to look at this Nokia Lumia 520, apparently it turned on one day and displayed this error message "unable to find a bootable option. Press any key to shutdown"
Nokia Software Update for Retial recognises the phone and says software can be installed:
This downloads fine and starts the install process, however always fails with the message "phone not supported by nokia software updater retail"
I have also tried using NaviFirm+, searching for the product code 059S3T5 which lets me download the RM914_3058.50000.1425.0006_RETAIL_eu_euro1_327_06_452364_prd_signed firmware.
However i'm unable to flash this with the Nokia Care Suite, it states: 0xFA001106: Signature check of FFU file fails. Reason(s): The FFU file is not correctly signed or not signed for this device.
Has anyone got any suggestions on what else i can try to flash this firmware? or to try fix the phone?
I was following the tutorial here Flash/unbrand Lumia devices thinking if the firmware was re flashed all would be fine.
Cheers for any advice
Click to expand...
Click to collapse
hy bro try this...... http://forum.gsmhosting.com/vbb/f67...mc-error-unable-find-bootable-option-1931094/ i have sucses

feherneoh said:
I have seen this error millions of times on 520, and could fix it always
what you'll need:
PC
micro USB cable
WPInternals
.hex loader for 520
.ffu for 520
T4 screwdriver
Small wire
All you have to do is to short the resistor on eMMC clock lane, and connect USB, phone will be in emergency mode. You can either select unlock or relock in WPInternals, but for unlock, be sure to use an SBL3, because that won't fix the problem on its own.
The best would be selecting relock, then flashing the ffu, so EFIESP gets fixed
If you need help finding that resistor, PM me
Click to expand...
Click to collapse
Ok, so I found the resistor on a picture in another forum - so I just short it out and connect to USB while still shorted?