Sorry for the possible errors in the writing, but as I have a basic english, I used google translator, and he sometimes modifies a little the text. Let's go to the point.
Guys, is the following. I changed the ROM of my android (LG Optimus L3) to CM9, but its bugs were bothering me, and then I decided to change. In that exchange,I ended up installing a ROM worse, she was not stable, full of errors, and then decided to return to the original ROM. Was in exchange ROM process that started the problem.I was trying to install the firmware V10D, and the KDZ was reporting error, but the tutorial I used said that this was normal error information and that I do not disconnects the phone from the computer until "FINISHED" appears on the KDZ, but I stubbornly and much IDIOT in subject withdraw before the hour and then tried the process again (I THINK THIS BROUGHT ALL THAT PROBLEM).
In another attempt appeared the same error message in KDZ but I wanted to wait and let the process going on the computer and went to the kitchen (I say this just to you know out that might have appeared some warning, but I did not see) when I returned the phone was off, I saw that the KDZ had the phrase "finished" then disconnected the phone, he was ready already "broken" tried and tried but he did not call, I connected the phone to the computer again but no signal, remove battery, I tried to get into "emergency mode", tried the hard reset but it just did not work. Will the process badly done by me blew the motherboard? HELP ME, PLEASE.
My email is : kaahm.s @ hotmail.com
Sorry for the possible errors in the writing, but as I have a basic english, I used google translator, and he sometimes modifies a little the text. Let's go to the point.
Guys, is the following. I changed the ROM of my android (LG Optimus L3) to CM9, but its bugs were bothering me, and then I decided to change. In that exchange,I ended up installing a ROM worse, she was not stable, full of errors, and then decided to return to the original ROM. Was in exchange ROM process that started the problem.I was trying to install the firmware V10D, and the KDZ was reporting error, but the tutorial I used said that this was normal error information and that I do not disconnects the phone from the computer until "FINISHED" appears on the KDZ, but I stubbornly and much IDIOT in subject withdraw before the hour and then tried the process again (I THINK THIS BROUGHT ALL THAT PROBLEM).
In another attempt appeared the same error message in KDZ but I wanted to wait and let the process going on the computer and went to the kitchen (I say this just to you know out that might have appeared some warning, but I did not see) when I returned the phone was off, I saw that the KDZ had the phrase "finished" then disconnected the phone, he was ready already "broken" tried and tried but he did not call, I connected the phone to the computer again but no signal, remove battery, I tried to get into "emergency mode", tried the hard reset but it just did not work. Will the process badly done by me blew the motherboard? HELP ME, PLEASE.
My email is : kaahm.s @ hotmail.com
Related
Sorry for the possible errors in the writing, but as I have a basic english, I used google translator, and he sometimes modifies a little the text. Let's go to the point.
Guys, is the following. I changed the ROM of my android (LG Optimus L3) to CM9, but its bugs were bothering me, and then I decided to change. In that exchange,I ended up installing a ROM worse, she was not stable, full of errors, and then decided to return to the original ROM. Was in exchange ROM process that started the problem.I was trying to install the firmware V10D, and the KDZ was reporting error, but the tutorial I used said that this was normal error information and that I do not disconnects the phone from the computer until "FINISHED" appears on the KDZ, but I stubbornly and much IDIOT in subject withdraw before the hour and then tried the process again (I THINK THIS BROUGHT ALL THAT PROBLEM).
In another attempt appeared the same error message in KDZ but I wanted to wait and let the process going on the computer and went to the kitchen (I say this just to you know out that might have appeared some warning, but I did not see) when I returned the phone was off, I saw that the KDZ had the phrase "finished" then disconnected the phone, he was ready already "broken" tried and tried but he did not call, I connected the phone to the computer again but no signal, remove battery, I tried to get into "emergency mode", tried the hard reset but it just did not work. Will the process badly done by me blew the motherboard? HELP ME, PLEASE. :crying::crying::crying::crying:
My email is : kaahm.s @ hotmail.com
Sorry for the possible errors in the writing, but as I have a basic english, I used google translator, and he sometimes modifies a little the text. Let's go to the point.
Guys, is the following. I changed the ROM of my android (LG Optimus L3) to CM9, but its bugs were bothering me, and then I decided to change. In that exchange,I ended up installing a ROM worse, she was not stable, full of errors, and then decided to return to the original ROM. Was in exchange ROM process that started the problem.I was trying to install the firmware V10D, and the KDZ was reporting error, but the tutorial I used said that this was normal error information and that I do not disconnects the phone from the computer until "FINISHED" appears on the KDZ, but I stubbornly and much IDIOT in subject withdraw before the hour and then tried the process again (I THINK THIS BROUGHT ALL THAT PROBLEM).
In another attempt appeared the same error message in KDZ but I wanted to wait and let the process going on the computer and went to the kitchen (I say this just to you know out that might have appeared some warning, but I did not see) when I returned the phone was off, I saw that the KDZ had the phrase "finished" then disconnected the phone, he was ready already "broken" tried and tried but he did not call, I connected the phone to the computer again but no signal, remove battery, I tried to get into "emergency mode", tried the hard reset but it just did not work. Will the process badly done by me blew the motherboard? HELP ME, PLEASE. :crying::crying::crying::crying:
My email is : kaahm.s @ hotmail.com
Hello guys.
I have an LG L5 (E610) that is having a very strange behavior.
It started by throwing a lot of ANR with different applications (Google Play Store, Play Services, Facebook, and others).
So, seeing this, I decided to do a factory reset. After reboot, what is my surprise that I see everything as I had before. All the applications, all the data, everything.
With this, I tried almost everything at the moment. And by saying that, I mean:
- Tried to follow the key combination for the recovery, it goes to recovery, I see the Android and some progress bar moving, but after the reboot, the system remains with no change;
- When on the system, I uninstall applications, they seem to be uninstalled, but after a reboot all the applications are back.
- Tried to root the phone with more than one process, no success. I cannot install any application. Not via play store, not via adb install, there is no way;
- Tried to flash a recovery img, to try to clean cache partition from there, no luck. From Fastboot it says everything went well, but when I reboot, everything is the same;
- In fastboot, I tried to erase cache and userdate partitions, no luck. When I try, i have a message saying "FAILED (status read failed (Too many links))". This happens with all the partitions. I even tried to erase the system partition, and I have the same response. Strange thing is that after this error, the phone reboots and goes directly to the system;
- Tried with KDZ images and tools to install different versions, I receive errors during the deployment and at the end the phone reboots. Again, the same system is installed as before. No changes.
As of now, I was trying to understand if there is any problem with the internal flash system. Maybe it is corrupted and is causing all these issues.
The thing is, as the phone is not rooted, I cannot launch a e2fsck to the maybe faulty mmcblk0pXX
The phone has a stock ROM based on Android 4.0.3 (build IML74K / LG-E610-V10e-JUN-30-2012)
I am out of ideas, I've looked around here at XDA, Google and I have no other ideas to try.
Does anyone have another suggestion?
Is there something else I can do to try to make the phone live again?
Any help someone can provide will be very much appreciated..
Now this is what I call a coincidence.
About 2 years ago, a friend of mine asked me for help with her E610. Almost all actions were giving us ANRs. Whatever you do, i.e. unsinstall, install, change, delete... after reboot/reset were all there, even notifications! Tried KDZ updater, and, while the update was OK without signs of errors or so, after reboot - nothing, everything was like before. After trying to find a solutions by hundreds of ways, with adb and fastboot commands (all partitions&folders were locked, no read, no write, and you can't see any file, tried root to no avail), L5 got bricked. She already got a new phone and this LG was laying there without any use.
Three days ago I decided to try again, with no hope tbh No screen, no vibration, nothing, apparently dead. But, I could install Qualcomm drivers and my Windows can see it in download mode. I think that the only way is to flash the phone with LGFlashTool and using COM port. I already extracted *.dz from *.kdz but I need the dll for FlashTool. Found 2 or 3 webs with this dll, but you need a 100 bucks subscription :crying: If anyone can upload that dll I'd be very happy to try to flash this phone I'm really big n00b in this, just a plain phone user, nothing more, so don't blame me if I said something wrong
Many thanks in advance.
same problem
Hello! Same problem...
My L5 is making me crazy... It has CyanogenMod 10 nighlty. A friend of mine was using it and he tried to install the GAPPS after he did a factory reset. I have no idea what guide he used but it got soft bricked... It's constantly showing a "stopped working" message and after a while reboots by itself.
I tried to do a factory reset but it always returns to the same point, same apps installed, everything like the reset never happened. I even used CWM to reset it and it allways goes back to the same recovery point.
After a while I decided to flash a stock room but here's the problem: I can't get into emergency mode.
After reading ALL post about it I found that there's at least three ways of entering EM, (1) down VOL and plug in usb cable without battery; (2) down+up VOL and plug in usb; (3) down+up VOL + power botton.
Conclusions:
(1) - gives me a screen full of code like a command line
(2) - White screen
(3) - White screen
I've read ALL the unbrinking post on the internet, including xda, and none of them helped.
The KDZ Updater never recognizes the phone. I installed all the drivers but everytime I plug in the phone it installes the same LGE MTP drive...
Can anyone help, please?!
How to enter Emergency mode? How to flash another rom?
Hello,
i have a problem with my 1 week old yotaphone and hope you guys can help me to solve.
Let me say, this is my first android device. After a long time using iphones i saw this 2-displays concept and wanted to give it a try.
But now my problem and the way to:
The phone was brand new and first of all i charged it for a wohle night.
After that i put in the sim-card and started the phone and walked through the start-procedure with WLAN, Googleaccount etc.
Then the phone told me about an update and i started it over WLAN.
The phone was downloading, rebooting and shows me a white window "updating x of 127(?) Apps".
Somewhere in the middel the phone rebooted again and now its in a bootloop.
What is possible with the phone right now.
I can start the phone wit the bootloop (powerred byAndroid, then restart)
I can use "Power + Vol-" to bring it into downloading mode
When i use "Power + Vol+" nothing happend.
When i use "Vol+ + Vol-" nothing happend.
The akku of the phone is empty now and it only works with usb or power unit connected.
In bootloop or downloading mode it is not charging.
What i tried.
What i try:
I read many topics with bricked / bootlooped yotphones and how to flash or cache whipping.
i connected the phone to my pc and used yotoflasher with many different firmwares.
I used fastboot:
- flashed the system.ing with differnet sizes.
- tried different custom recovery.img from different threads here and from other sites.
Even a complete new image, moddified RU img doesn`t help.
The phone stays in bootloop.
Yes, it`s a warranty case, but before i start to strech my nerves by handling with the dealer and shipping
this phone back to china i will try everything else and hope you can help me out of this situation.
Thanks a lot
easyxx said:
Hello,
i have a problem with my 1 week old yotaphone and hope you guys can help me to solve.
Let me say, this is my first android device. After a long time using iphones i saw this 2-displays concept and wanted to give it a try.
But now my problem and the way to:
The phone was brand new and first of all i charged it for a wohle night.
After that i put in the sim-card and started the phone and walked through the start-procedure with WLAN, Googleaccount etc.
Then the phone told me about an update and i started it over WLAN.
The phone was downloading, rebooting and shows me a white window "updating x of 127(?) Apps".
Somewhere in the middel the phone rebooted again and now its in a bootloop.
What is possible with the phone right now.
I can start the phone wit the bootloop (powerred byAndroid, then restart)
I can use "Power + Vol-" to bring it into downloading mode
When i use "Power + Vol+" nothing happend.
When i use "Vol+ + Vol-" nothing happend.
The akku of the phone is empty now and it only works with usb or power unit connected.
In bootloop or downloading mode it is not charging.
What i tried.
What i try:
I read many topics with bricked / bootlooped yotphones and how to flash or cache whipping.
i connected the phone to my pc and used yotoflasher with many different firmwares.
I used fastboot:
- flashed the system.ing with differnet sizes.
- tried different custom recovery.img from different threads here and from other sites.
Even a complete new image, moddified RU img doesn`t help.
The phone stays in bootloop.
Yes, it`s a warranty case, but before i start to strech my nerves by handling with the dealer and shipping
this phone back to china i will try everything else and hope you can help me out of this situation.
Thanks a lot
Click to expand...
Click to collapse
Mine too,stuck in bootloop. I also tried the fastboot and it said waiting device.
kophyo07 said:
Mine too,stuck in bootloop. I also tried the fastboot and it said waiting device.
Click to expand...
Click to collapse
If your phone displays Downloading... and fastboot keeps saying waiting for device then there is something wrong with the installed ADB driver. Check some of the posts in this forum like this one on how to fix this. http://forum.xda-developers.com/yotaphone-one/help/yotaphone-2-yd-206-china-flash-firmware-t3306797/post69311402#post69311402
Strange that you had an OTA (Over The Air update). You didn't do anything between the SIM/Google registration and OTA ?
Normally there are no OTAs allowed on yd206 phones bought from China/HK , where did you buy it ? Chinese retailers have their own firmware that they put on phones , for me , maybe you had bad firmware installed.
The warranty of your phone is voided if you flash yotaphones bought from China and HK .
When you use yotaflasher do you get error message or "waiting for device" ?
To flash the Yotaphone , it should be in developer mode , but you couldn't put it in this mode because it first did the OTA that started your bootloop. Android apps are updated like that ("installing x of 127") when it gets updated to lollipop. Normally the OTA should have worked OK. Did you allow enough time at the Yotaphone logo after the first reboot ? It stays on this logo for 5 minutes before starting. I made this mistake.
The OTA started just after you set up Google etc ?
If so, normal yotaflashing will never work, but at least you havent broken the warranty . The thing we need to know is what exactly happened when you tried to flash , what errors messages appeared ?
If you did not put the phone in developer mode, then you cannot easily flash the phone, so your best possibility is to return the phone. Normally you can contact the seller by chat or email . Some are very good in exchanging.
It IS possible to flash your phone using fastboot, but I would not personally attempt it and you would lose your warranty . You need rootkits, SDK toolkits, universal drivers and images. Google "bootloop without USB debugging".
When I flashed my yd206 , (after many attempts) I flashed my yd206 to yd201 Russian KitKat ROM first and then did an OTA to lollipop.
Hi.
To start off, I'd like to say im no expert with phones, I had phones mostly to call, watch videos and listen to music, and this is my first attempt at doing all the stuff I will be describing now.
From the beginning:
I bought a seller refurbished LG G2, which worked fine when I received it, I had to do some updates which my phone found automatically, and it ended at OS version 4.4.2.
I wanted to finally have a decent but cheap phone, however it couldn't play some games I wanted to play and thought "Maybe if I update OS to something new, it will work, and it looks better"
Here my journey to update the phone to Android 11 started.
I was looking at many different videos and guide and everything, how to root, first time I rooted was by accident, only later a better video instructed me how to do it properly, then I installed the trww or whatever its called. then it didnt work properly after using that recovery to install android 11, so I had to flash it to some old version I found for my device (My version is LG D802 btw). For some reason it now had only 11gb of space, instead of 32gb. Anyway, I tried installing root and twrw thing again. After getting root and the recovery program I clicked reboot in its options and now my phone is having an issue.
First off, I left it to charge over 9 hours. If its NOT connected via usb it does nothing, power button, volume buttons do nothing.
I tried connecting it to my phone to flash it, but nope, after few seconds it says my phone disconnected from the usb and try again, even tho it is connected and I can see in device manager that it's seen by my PC. Now, I tried to enter the download mode manually, and it worked.
It says that it's rooted and B0 above it (this number was going down over different roots, twrw installs and flashes and such, no idea what it is.
I tried to flash it again since Im in download mod, however now the main issue appeared. It goes well for 40% of the flash using the LG flash tool 2014, I can see the progress in the download mode on the phone's screen, however once it reaches that certain point it just resets and the program treats it as disconnected.
Now when I have the phone connected via usb it just flashes red between 1 and 3 times, LG logo shows up for several seconds, then it turns off, and repeats the whole process.
During the flashing, software instructed me to remove the batter and try again, so I looked up how to remove it, did it, put everything back together, and its still the same.
Please tell me what to do, I've already spent over 10 hours trying to fix it and I just bought this phone...
hi... if your phone flashes LG logo - i'd recommend a full TOT flash of the original Lollipop image as a starting point...
just make sure you download a proper TOT file for your d802 device (32gb model)...
you'll end up with a working stock Lollipop rom which you can later root and flash a custom rom (i.e. Lineage 18)
Stock TOT file is usually about 2.6-2.7GB in size (at least for my 16gb model)
this youtube video shows how to do it and what is required for the process...
i think there is also an older thread here on XDA on how to TOT flash a G2 device (try to search it)