Related
I use the xda2unlock.
I have done it.
• You firstly need to put your xda II in the boot up mode Note: THIS WILL WIPE YOUR USER DATA SO ENSURE YOU HAVE BACKUP UP ALL YUR DATA ON YOUR PC.
• To enter the boot loader mode Hold the Power button and the Action button while pressing the stylus in the reset hole on the bottom.
• If you are in boot loader mode the screen will go gray and display serial at the top of the screen.
• Put the device in the USB cradle. The display will now say USB on the PDA and your pc will detect the PDA.
• Display USB in Active sync in 'File -> Connection Settings'
• Run the xda2unlock program.
• Type YES when requested by the unlock program and then press Enter on the PC keyboard.
When I type YES en my computer, this program return:
ERROR: OpenComport \\.\WCEUSBSH001 - Acceso denegado. :shock:
xa2 unlock
Try running the latest version of the unlock program no need to reset the xda or go into bootloader mode. It worked great on my xda 2
dont say thanks
Dont bother saying thank you for your help, will you?
Has someone connected a laptop to internet using TyNT?
I cant. I did it with my htc universal using the wireless modem or internet sharing (aku 3.2).
But TynT hasnt "internet sharing utility" and my laptop doesnt recognize it as modem. Some idea?
thanks
Do you have under programs wireless modems? If you launch this and got to usb then start; your laptop/pc will pnp and request instalation of drivers, I think the drivers and software are on the wiki. Also remember to use the correct APN name i.e. for T-mob uk it is general.t-mobile.uk
cool this worked fine for me, i just needed to change the apn settings from "internet" to "general.t-mobile.uk"
Check the Hermes FAQ: there's a section about using TyTN as a laptop modem...
http://wiki.xda-developers.com/index.php?pagename=Hermes_FAQs
Bye
It worked when i used my Univesal. But now, when a click "start" in wireless modem app and plug it to the laptop nothing happens.....No hardware detected......
im usin orange spv m500. when i connect the phone to my laptop using USB cable, nothin happens. no hardware detected. it doesnt prompt to install any driver.. pls help!! :!:
It works fine for me with a BlueTooth connection. I don't think anybody has it working over USB.
It works fine using a Dial-up Connection from Windows.... you don't need to activate the Wireless Modem on the TyTN... in fact doing so will prevent it from working...
Hi.Yes, it works setting a dial-up connection with bluetooth but i want to use the wireless modem usb because the dial-up system closes the connection if you receive a phone call.......
I miss the utility "internet sharing" from Universal Aku 3.2. I hope it is present in next TyNT rom....
i have found the solution
go to start > programs > wireless modem
select connection type USB
tap Start
then connect ur mobile device to ur laptop or pc. it will detect new hardware n will prompt to install driver. u can download the driver and utility from here
Code:
http://dl1.uploadgalaxy.com/files/e52d58daacf8/USB_Modem.zip.html
when I plug the tynt in my pc or my laptop (with the wireless app running on usb) nothing happens....
mine is a spv m500. OS is windows mobile 2003. it detects new hardware only when u plug in after pressing the start button
Yes. I have Imate pocket pc and Imate jasjar and it works in than way. But it doesnt work with TyNT (for me)
shafiu said:
i have found the solution
go to start > programs > wireless modem
select connection type USB
tap Start
then connect ur mobile device to ur laptop or pc. it will detect new hardware n will prompt to install driver. u can download the driver and utility from here
Code:
http://dl1.uploadgalaxy.com/files/e52d58daacf8/USB_Modem.zip.html
Click to expand...
Click to collapse
Hi I used have functional connection from my laptop to TyTN using USB cable. but since last week it started telling me that there is some remote access error (I have tried different cable to check whether it is broken or not ... didn't help)
so I removed the HTC USB modem .. so I could re-do it .. since then I can't install it again .. it evern doesn't detect the TyTN so I could process it using wizard mode .. and when I want to do it manually it doesn't work as well
can somebody please help?
thx in advance
dherrero said:
when I plug the tynt in my pc or my laptop (with the wireless app running on usb) nothing happens....
Click to expand...
Click to collapse
Yup, exactly the same here, any ideas anyone?
Thanks.
M.
have you
1. disabled USB/Serial connections in ActiveSync and
2. started the "Wireless Modem" application?
not helping .. I am starting to think about HR .... BT connection is toooo slow :/
EDIT .. I have used HR ... created new connection .. tested it (it worked) and used back-up .. now it doesn't work again and keep teeling me about some access error 680
I am going for finall HR I am affraid ...
a BT modem connection will at best have less than half the speed of a wired USB one... (see my previous benchmark thread).
goestoeleven said:
have you
1. disabled USB/Serial connections in ActiveSync and
2. started the "Wireless Modem" application?
Click to expand...
Click to collapse
Yes i have do so but nothing append pc dont want see the tynt.
I have try 3 part program like mobile stream usb modem...
But nothing work for me..
I have give a look to wiki faq but nothing this url:
thread 1:http://forum.xda-developers.com/viewtopic.php?t=59586 and
Thread 2; http://forum.xda-developers.com/viewtopic.php?t=57841 are simply death link...
Have somebody an idea???
thx
works through usb no problem
Part I: Install USB Modem Driver
1. Make sure that your PocketPC does not connect with your PC
2. Disable ActiveSync USB port connect on your PC
3. Tap device Start->Programs->Wireless Modem -> Tools->Options, and input your APN of your service provider. Then tap “OK”
4. Make sure the “Connection Type” selected ”USB” , Now press the button “Start” , and connect your device with PC through USB cable
5. On your desktop PC will found a new hardware
6. Select “No, not this time” and press “Next”
7. Select “Install from a list or specific location (Advanced)” and press “Next”
8. Specify USB Modem driver(USBMDM.inf) path and press “Next”
9. Press “Continue Anyway” to continue install USB Modem driver
10. Press “Finish” to finish driver install
11. After installation you have a new USB Modem called “HTC USB Modem” in Control Panel->Phone and Modem Options
Part II: Create New USB Dialer
1. In “Control panel”, select “Network Connections”
2. Click “Create a new connection”
3. Press “Next” to start Dialer create process
4. Select “Connect to the Internet” then press “Next”
5. Select “Set up my connection manually” then press “Next”
6. Select “Connect using a dial-up modem” then press “Next”
7. Select your “USB Modem” then press “Next”
8. Input modem ISP Name, like “ABC”, then press “Next”
9. Input dialup number “*99#” then press “Next”
10. Select “Anyone’s use” or “My use only” then press “Next”
11. Input “User Name” and “Password”, default is empty, then press “Next”
12. Check/Uncheck “Add a shortcut to this connection to my desktop” then press “Finish”
13. After setup completed, you can see a new dialer in “Network Connections”
14. Execute your new USB Modem Dialer(ABC)
15. Press “Dial” to dialup to network
works 100% tried it fine. document was taken off somewhere i think on the wiki so no thanks to me. Just to confirm via usb works fine and it is quick
sk8funk said:
Part I: Install USB Modem Driver
1. Make sure that your PocketPC does not connect with your PC
2. Disable ActiveSync USB port connect on your PC
3. Tap device Start->Programs->Wireless Modem -> Tools->Options, and input your APN of your service provider. Then tap “OK”
4. Make sure the “Connection Type” selected ”USB” , Now press the button “Start” , and connect your device with PC through USB cable
5. On your desktop PC will found a new hardware
6. Select “No, not this time” and press “Next”
7. Select “Install from a list or specific location (Advanced)” and press “Next”
8. Specify USB Modem driver(USBMDM.inf) path and press “Next”
9. Press “Continue Anyway” to continue install USB Modem driver
10. Press “Finish” to finish driver install
11. After installation you have a new USB Modem called “HTC USB Modem” in Control Panel->Phone and Modem Options
Part II: Create New USB Dialer
1. In “Control panel”, select “Network Connections”
2. Click “Create a new connection”
3. Press “Next” to start Dialer create process
4. Select “Connect to the Internet” then press “Next”
5. Select “Set up my connection manually” then press “Next”
6. Select “Connect using a dial-up modem” then press “Next”
7. Select your “USB Modem” then press “Next”
8. Input modem ISP Name, like “ABC”, then press “Next”
9. Input dialup number “*99#” then press “Next”
10. Select “Anyone’s use” or “My use only” then press “Next”
11. Input “User Name” and “Password”, default is empty, then press “Next”
12. Check/Uncheck “Add a shortcut to this connection to my desktop” then press “Finish”
13. After setup completed, you can see a new dialer in “Network Connections”
14. Execute your new USB Modem Dialer(ABC)
15. Press “Dial” to dialup to network
works 100% tried it fine. document was taken off somewhere i think on the wiki so no thanks to me. Just to confirm via usb works fine and it is quick
Click to expand...
Click to collapse
Hi, read/found it somewhere in the wiki, and it works as you described.
Only thing is always start the modem first before connecting to the PC. Works everytime for me:
Connected speed: 230.4 kpbs (good enough for me as I'm on EDGE connection)
Regards,
Does anyone know information about how to connect the Samsung Fascinate as Diag Mode driver? ie: this type of connection needed for QPST/QXDM/CDMA Workshop.
I tried 'debugging mode' enabled from the settings in the Applications, but it didn't create any new port that would recognize for my phone.
The Epic solution is pretty strait forward
Install USB Drivers:
32 Bit or 64 Bit
Put phone into DIAG mode:
Dial ##8778#
Select UART = Modem, USB = Modem.
Click to expand...
Click to collapse
This doesn't seem to work on Fascinate though.
Go to Settings - Wireless Networks - Click to Dialup Networking this will also put it in Dialup mode
hetaldp said:
Go to Settings - Wireless Networks - Click to Dialup Networking this will also put it in Dialup mode
Click to expand...
Click to collapse
wow man, thanks a lot that worked.
Remember to put it Again Dialup Networking off
Thank you for the steps. I was also able to get the phone to be read by QPST and CDMA Workshop. The odd thing is that when I tried to read the phone again the next day, none of the software will read the phone. Interestingly, I can see the COM port and the Modem port in the Device Manager, but the software refuses to read the phone. I am wondering if I accidentally changed one of the settings to turn it into UART or something to this effect, but the code that I found for this (##UPST#) does not work on the phone, even with hidden menu enabled. Any suggestions, currently I am stuck with a phone that can only do voice and text, no 3G? Thank you in advance!
You could try Diag mode
Diag/Testing Mode
*#4636*1111#
QPST sees it, but nothing is editable, in Dial-Up mode?
Thank you for your response! I tried that, it took me to the menu, plugged the phone to the PC, Device Manager shows Samsung Diagnostic Port, I use CDMA Workshop to try to at least read the phone. I connect to the correct COM port, but CDMAWS fails in reading it. I don't get it, it used to work fine with almost the exact same setup. I uninstalled the drivers, reinstalled them, same thing. Wiped the phone, same thing. Kind of frustrating. The only resort I have now is to maybe just get it fully flashed to stock so that I can start from scratch again. Odd, I have never had a phone that was giving me a COM port that phone software consistently fails to read, especially when it worked before. lol. Any assistance with anything else I may try would be greatly appreciated.
**usbui select Modem.. and
Bringing this issue up.... I cannot get it to work. I've read tons of threads and everyone says go to Device Manager and click Ports and then change the port on the Samsung to port 1 and it will show up blah blah Blah.... there is no list that says "Ports" in Device Manager. I have this DialUpNetworking thing checked and debug mode and the port1 shows up in QPST but it says "No Phone". And yes all drivers are installed.
Diag/Testing Mode
*#4636*1111# ??????
That doesn't do jack. It just lets me input the numbers and when I press the last #, all the numbers vanish. I need this to work or I have to get a different Phone.
nFiniti said:
Bringing this issue up.... I cannot get it to work. I've read tons of threads and everyone says go to Device Manager and click Ports and then change the port on the Samsung to port 1 and it will show up blah blah Blah.... there is no list that says "Ports" in Device Manager. I have this DialUpNetworking thing checked and debug mode and the port1 shows up in QPST but it says "No Phone". And yes all drivers are installed.
Diag/Testing Mode
*#4636*1111# ??????
That doesn't do jack. It just lets me input the numbers and when I press the last #, all the numbers vanish. I need this to work or I have to get a different Phone.
Click to expand...
Click to collapse
Do a search in general...i posted how there. It's like *33 something.
**33284 is what ur looking for
Edit: you need to set up the com. That requires knowing the port and putting the phone into dial up mode.
TRY **USBUI (**87284)
You can switch the UART and USB from PDA to MODEM here.
denonlake said:
TRY **USBUI (**87284)
You can switch the UART and USB from PDA to MODEM here.
Click to expand...
Click to collapse
No, I know exactly what he's doing. The phone needs to be in network dial up mode. But for qpst to reckognize it, he needs to add the com.
I found that only the .323 version of qpst worked for me. Also there is the *229 (i think) will reprogram those settings you may have messed up, maybe try that?
Sent from my rooted froyo Fascinate
ziggy484 said:
I found that only the .323 version of qpst worked for me. Also there is the *229 (i think) will reprogram those settings you may have messed up, maybe try that?
Sent from my rooted froyo Fascinate
Click to expand...
Click to collapse
323 works for basic flash, however if he's trying to get ppp configs setup for 3g and what not, he will need build 215. 323 will always revert to the original settings. If he's just trying to flash the prl, then it's no big deal. If he's trying to flash over to a different carrier, then it'll revert to vrz settings.
Menu > Settings > Wireless & Networks
Enable Dial up Networking
Next..
Menu > Settings > Applications > Development
Enable USB Debugging
-------------------------------------------
If Dial-up Networking is not showing perform the following. Dial **33284 followed by SPC (000000 or 468346 ) then scroll to Port Map and select HFK,DIAG. Once this is complete, you should now have Dial-up Networking showing up under Wireless and Network.
Bypass Activation:
Press "Emergency Call"
Dial *#83786633 then press send
After you press "send" press the "home" key and you should now be passed activation
this worked in getting the fascinate into daig mode. thank you!!!
JUSMEJOSE said:
Menu > Settings > Wireless & Networks
Enable Dial up Networking
Next..
Menu > Settings > Applications > Development
Enable USB Debugging
-------------------------------------------
If Dial-up Networking is not showing perform the following. Dial **33284 followed by SPC (000000 or 468346 ) then scroll to Port Map and select HFK,DIAG. Once this is complete, you should now have Dial-up Networking showing up under Wireless and Network.
Bypass Activation:
Press "Emergency Call"
Dial *#83786633 then press send
After you press "send" press the "home" key and you should now be passed activation
Click to expand...
Click to collapse
pkopalek said:
You could try Diag mode
Diag/Testing Mode
*#4636*1111#
QPST sees it, but nothing is editable, in Dial-Up mode?
Click to expand...
Click to collapse
thanks dude your really great i'll bet you make your company lotta money
i need the 16 digit password to change the serial number in sansung galaxy s i400
hello
i need the 16 digit password to change the serial number in sansung galaxy s i400 in cdma works shop please
---------- Post added at 06:18 PM ---------- Previous post was at 06:09 PM ----------
denonlake said:
TRY **USBUI (**87284)
You can switch the UART and USB from PDA to MODEM here.
Click to expand...
Click to collapse
i need the 16 digit password to change the serial number in sansung galaxy s i400 to cdma works shop please
JOSEUBIERA said:
hello
i need the 16 digit password to change the serial number in sansung galaxy s i400 in cdma works shop please
---------- Post added at 06:18 PM ---------- Previous post was at 06:09 PM ----------
i need the 16 digit password to change the serial number in sansung galaxy s i400 to cdma works shop please
Click to expand...
Click to collapse
A quick interweb search brought up this number for the Samsung Continuum SCH-I400
20 10 03 16 19 81 02 19
.
At an other board I read that the LG E900 Optimus7 phone provides a factory menue that could be activated with the following code:
##634# + Green Make Call Key
and then enter 277634#*# als password
I still don't know what is visible and changeable in factory menue. I would be intressted if there is also an netmonitor / field test display included.
From the menu are accessible different functions like hardware tests and usb mode change to enable thethering and USB modem (that one is a MUST if you want to flash the phone, by the way is Qualcomm QC mode...)
The hack began!
Hello Guys,
my phone is unroot. I dont want root
Firmware is G928CXXU2AOJ5
CSC KSA
How can a access the band selection, so i can set to lte band 20 only.
The Code i found
*#0011# (works for access service mode)
More - Press Back
More - Insert Q (don't work)
More - Insert 0000 (don't work)
also*
More - Insert Q0000 (don't work)
More - Insert Q1 (don't work)
More - Insert Q0 (don't work)
The Code
*#2263* also don't work.
Has anybody a idea or a code how do can i access the band selection without root?
I tried with phone info, but also don't work.
thanks