hi my phone is htc magic 32 b i have atach two photos, for my information
i have follow this tuto :
CLShortFuse for making super easy Rooting method. Original topic.
SuperOneClickv2.3.3 .... and it says that my phone was done successfully root
and next step i have follow this tuto:
http://forum.xda-developers.com/showthread.php?t=529019
but when i do this:
fastboot flash recovery recovery-RA-sapphire-v1.7.0G.img
i have this result :
C:\Android>fastboot flash recovery recovery-RA-sapphire-v1.7.0G.img
sending 'recovery' (4520 KB)... FAILED (remote: not allow)
finished. total time: 0.001s
and now pls can someone help me wich tuto must follow to install custum rom or what to do
thank you
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Not development topic!
Anyway, it's better to upgrade your phone to newest combo
Scenario:
1. in fastboot-mode (like at first screen) run
Code:
fastboot getvar cid
fastboot getvar cidnum
You will get your regional customerid (CID)
2. According CID choose appropriate RUU from library in section "Vodafone Magic / Sapphire 32B: http://forum.xda-developers.com/showthread.php?t=659403
3. Run it. Now you have build number CRC24 (Android 1.5), after RUU you will have build number DRC92 (Android 1.6), but it is not enough.
4. Then you need apply two update files to get hboot 1.33.0013 / radio 2.22.28.25 (VODAFONE OTA UPDATE from DRC92 to FRG83D)
This combo is most used combo for Magic 32B now. You will have Android 2.2 too.
5. At this step you need get root again (cause it will disappear while installing official roms). Run SuperOneClick
6. Even on Android 2.2 you can not run "fastboot flash recovery recovery-RA-sapphire-v1.7.0G.img", cause hboot 1.33.0013 does not allow it too like hboot 1.33.0007
In this case you need follow steps 5, 7, 9 (only these) from manual: http://forum.xda-developers.com/showpost.php?p=7707672&postcount=1
p.s. Sure, you can do step 6 instead to get custom recovery, but your current combo (hboot/radio) is not used in custom roms. So you have to change it in future. It's better to change them first following all steps in this post.
thank you so much now i have 2.2.1 5[Strogino]
Related
I loaded new Radio, SPL and Recovery on my phone and lost recovery after that. So I decided to load TM 2.10 release and it overwrote SPL and got hung up loading Radio causing SPL Radio mismatch. Long story short, after that I got great help from mumilover to load SPL 1.33.0014G and unlock the bootloader. Loading of 1.33.0014G changed version-main to 3.57. However good news is boot, recovery and system image files can be loaded one by one making seperate ZIP files with custom android-info.txt files.
I tried cwm-carz-v4.0.1.4-0820-recovery, recovery-RA-sapphire-v1.7.0G, recovery-RA-magic+-v2.0.0.1-seo, recovery-RA-hero-v1.6.2, recovery-clockwork-2.5.0.7-sapphire and recovery_patched___ra162_635 recoveries, but none of them starts. Also tried to load boot and system images from various releases but with unsuccessful boot.
I tried to load recovery as boot but gives partion update error.
I am looking for any suggestion or special recovery or boot and system image enabling to give access to android system or recovery.
Phone display following on HBoot screen.
*** UNLOCKED ***
SAPPHIRE PVT 32A SHIP S-ON G
HBOOT-1.33.0014 (SAPP31000)
CPLD-13
RADIO-6.35.16.19
Jan 31 2012, 14:43:52
What's about mumilover? Did he help again? (He is best tech here)
p.s. try
Code:
fastboot flash recovery your_recovery.img
We could make our own recovery image, the source is open on git.
The only thing it has to do, is to flash eng spl on the device!
I have a school project due May 23 and have limited time... but you have me on skype, lets see what we can do :0)
I recovered my phone with XTC Clip
http://forum.xda-developers.com/showthread.php?t=1231297
However my HBOOT is at 1.33.0014, which is different then yours. Do you know XTC clip supports this HBOOT?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This is the latest firmware for HTC ONE M7 extracted from official OTA for TELUS, 5.11.661.8
You need unlocked bootloader and S-OFF
I removed Red Warning Text and flashed successfully on my phone.
This build is for
development purposes only
Do not distribute outside of HTC
without HTC's written permission.
Failure to comply may
lead to legal action.
The zip contain:
- firmware 5.11.661.8
- hboot 1.57.0000
- radio 4T.27.3218.14
- the new splash screen "powered by android"
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Download file and copy to your adb folder:
A - full firmware link removed
MD5 be417a18c76ef0e517f32266e4b5d744
B - hboot only link removed
MD5 4b74f5f8c47bdd6aa2fc20446e5ce743
DON'T REBOOT THE PHONE UNTIL YOU GET A SUCCESS MESSAGE
1 - Reboot bootloader
Code:
adb reboot-bootloader
2 - Reboot to RUU
Code:
fastboot oem rebootRUU
3 - Flash firmware
Code:
fastboot flash zip firmware_5.11.661.8_noredwarn.zip
Very important!!! One more time
Code:
fastboot flash zip firmware_5.11.661.8_noredwarn.zip
3b - Flash hboot only, if you want
Code:
fastboot flash zip hboot_1.57_no-red-warning.zip
4 - Reboot to bootloader and verify version
Code:
fastboot reboot-bootloader
5 - Reboot to system
Code:
fastboot reboot
6 - Enjoy
WARNING
Flash at your own risk, I can't be held responsible if you brick the phone!!!
If case you need original firmware for modelid: PN0712000 cidnum: TELUS001
The zip contain:
- firmware 5.11.661.8
- hboot 1.57.0000
- radio 4T.27.3218.14
- the new splash screen "powered by android"
- stock boot
- stock recovery
link removed
MD5 895F3ADD2CCC1DE09F85910DCFE94B99
If flashed successfully please post your modelid and cid here.
Thanks
Flashed succsessfully on PN0710000 with super cid...:good:
I'm looking for the Telus M7 firmware for sense 6 - why were the links removed in this thread?
Sent from my HTC One using Tapatalk
Can you help me? Bricked my phone!
So I did something pretty dumb yesterday. Installed the HTC Sense 6 update on my HTC ONE M7, hated it so decided to root my phone to revert back to Sense 5.0 or 5.5 or potentially try a custom ROM. Downloaded a Tmobile 4.3 JB RUU, downloaded android SDK, HTC sync manager, Fastboot. I unlocked boot loader, installed Wheaton recovery by Koush, installed SU, figured phone was rooted but it wasn't. Now I've somehow succeeded in deleting EVERYTHING. Phone continues booting into recovery. Commands using Fastboot aren't recognized because it cannot find any device. When plugged in via USB, PC recognizes that something is plugged in but that's about it.
M7_UL PVT SHIP S-ON RH
HBOOT-1.57.0000
RADIO-4T.27.3218.14
Open DSP-v32.120.274.0909
OS-5.14.531.1
eMMC-boot 2048MB
May 9 2014, 15:00:26.0
HBOOT
<VOL UP> to previous item
<VOL DOWN> to next item
<POWER> to select item
FASTBOOT
RECOVERY
FACTORY RESET
SIMLOCK
CHECK SMARTSD
IMAGE CRC
SHOW BARCODE
Any help will be greatly appreciated
rodenti said:
I'm looking for the Telus M7 firmware for sense 6 - why were the links removed in this thread?
Sent from my HTC One using Tapatalk
Click to expand...
Click to collapse
Some issues with corrupted zip files.
Download from here
http://forum.xda-developers.com/showthread.php?t=2485651
bonedatt said:
So I did something pretty dumb yesterday. Installed the HTC Sense 6 update on my HTC ONE M7, hated it so decided to root my phone to revert back to Sense 5.0 or 5.5 or potentially try a custom ROM. Downloaded a Tmobile 4.3 JB RUU, downloaded android SDK, HTC sync manager, Fastboot. I unlocked boot loader, installed Wheaton recovery by Koush, installed SU, figured phone was rooted but it wasn't. Now I've somehow succeeded in deleting EVERYTHING. Phone continues booting into recovery. Commands using Fastboot aren't recognized because it cannot find any device. When plugged in via USB, PC recognizes that something is plugged in but that's about it.
M7_UL PVT SHIP S-ON RH
HBOOT-1.57.0000
RADIO-4T.27.3218.14
Open DSP-v32.120.274.0909
OS-5.14.531.1
eMMC-boot 2048MB
May 9 2014, 15:00:26.0
HBOOT
<VOL UP> to previous item
<VOL DOWN> to next item
<POWER> to select item
FASTBOOT
RECOVERY
FACTORY RESET
SIMLOCK
CHECK SMARTSD
IMAGE CRC
SHOW BARCODE
Any help will be greatly appreciated
Click to expand...
Click to collapse
Post questions in Q&A section please
Thread closed at OP's request.
Hi Everyone,
I'm using a Moto X Pure Edition XT1575 32GB running MM 6.0 stock with Feb 1, 2016 security update with unlocked bootloader.
I wanted to flash the MM 6.0 factory images released by Motorola to revert my phone to complete stock and lock the bootloader again.
When I flash, I'm getting the following error
(bootloader) Preflash validation failed
FAILED (remote failure)
Please help... I have also attached a screenshot.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Why did you fastboot oem lock begin before flashing system images? That wasn't in the list of instructions that came with the file...
mxpe 6.0
Same thing happened to me and I didn't even use the fastboot oem lock.
If the February update changed the partition then it will fail. It also happens when you try to downgrade from 6.0 to 5.1.1. If that's the case, then you just ignore it and flash the other files.
Edit: I just checked in the update zip. It updates the partition so it can't be downgraded. Just ignore that and flash the other files.
Thanks. I'm actually in the progress of downloading the files straight from Motorola so I know for sure they are legit.
Thanks everyone, I will follow the instructions and flash others.
joeldroid said:
Thanks everyone, I will follow the instructions and flash others.
Click to expand...
Click to collapse
Let me know how it goes. I'm actually gonna go back to stock just to see if it works for future use. I just received my moto x pure yesterday. I don't think the stock rom is up to date like the files from the Motorola website.
got the same issue nothing seems to work. Any ideas ?
bskbeast said:
got the same issue nothing seems to work. Any ideas ?
Click to expand...
Click to collapse
There are a dozen threads here about flashing stock images... all of them talk about pre-flash validation errors... Maybe one my signature will help?
acejavelin said:
There are a dozen threads here about flashing stock images... all of them talk about pre-flash validation errors... Maybe one my signature will help?
Click to expand...
Click to collapse
i have tried several. When i get home i will look for yours.
Thanks
Hi
I installed latest 20s for lepro 3 x727 and i want to install cm.
The problem is that i cannot unlock the bootloader
It said remote unlock failed.
Maybe this update came with a security patch for stop unlock bootloaders.
chemicalboyxda said:
Hi
I installed latest 20s for lepro 3 x727 and i want to install cm.
The problem is that i cannot unlock the bootloader
It said remote unlock failed.
Maybe this update came with a security patch for stop unlock bootloaders.
Click to expand...
Click to collapse
Go to the persistent bootloader unlock thread, download the bootloader files, unzip and run these commands
fastboot flash xbl xbl.elf
fastboot flash aboot emmc_appsboot.mbn
Then reboot and do the bootloader unlock command.
I've been searching for an answer to this to avoid a new thread but I will ask here. Can you confirm that taking the 20s OTA after being on stock 19s that the same unlock methods and files do still work? Thanks in advance!
I did an ota update fully stock no root.
I can confirm that unlocking the method works multiple ways:
1: LeEco aio toolkit latest version
2: Both methods in the thread of persistant bootloader unlock 19's
suhridkhan said:
Go to the persistent bootloader unlock thread, download the bootloader files, unzip and run these commands
fastboot flash xbl xbl.elf
fastboot flash aboot emmc_appsboot.mbn
Then reboot and do the bootloader unlock command.
Click to expand...
Click to collapse
That worked!!! Thanks man
xerythul said:
I've been searching for an answer to this to avoid a new thread but I will ask here. Can you confirm that taking the 20s OTA after being on stock 19s that the same unlock methods and files do still work? Thanks in advance!
Click to expand...
Click to collapse
yes...
suhridkhan said:
Go to the persistent bootloader unlock thread, download the bootloader files, unzip and run these commands
fastboot flash xbl xbl.elf
fastboot flash aboot emmc_appsboot.mbn
Then reboot and do the bootloader unlock command.
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
. I can't get to flash the elf file
Sent from my SM-P600 using XDA-Developers Legacy app
how check which bootloader i have?
have new phone out of box with rom from 2016
So I'm trying to root my huawei p9 lite vns-l31 but had no luck
I did ulock bootloader and i do get the message when i reboot
but why i try to boot into the twrp from fastboot i get FAILED (remote: Command not allowed)
also the thing when you press the power button and vol up it will jsut reboot it
I tried many TWRP files none woked also I have android 7.0 and emui 5.0
P.S. sorry for bad english
Unlock bootloader again with ADB command:
"Fastboot oem unlock YOUR_CODE"
Reboot and flash a good version of TWRP for you.
Done!
Therand said:
Unlock bootloader again with ADB command:
"Fastboot oem unlock YOUR_CODE"
Reboot and flash a good version of TWRP for you.
Done!
Click to expand...
Click to collapse
Not working for me aswell
chakalovski2 said:
Not working for me aswell
Click to expand...
Click to collapse
What's not work?
ADB command?
Or fastboot?
What's return of command?
Error text?
What did you make on your phone?
How do you want help without explaining your problem?..
Hello,
When I try to send a command as flashing through fastboot it's telling me command not allowed it's kind of impossible to write or send data like a flash to my phone. Though the drivers are installed and adb too.
help me pls Command Not Allowed
I have bootloader code but when I write the command fastboot oem unlock ******* I get the command not allowed error 210 stock rom is not loaded with the three key method I want to install a twrp in vendor, system, product invalid argument error how to fixed pls help me (sorry my bad english) i can not open the oem lock because i do not know how to use the usb debug mode
Elite Rom 5.1 (Hassan Mirza) came to me after I uploaded it and I could not fix it again
TEL: P9 LİTE VNS-L31
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Please help me
did you fixed that error
Failed (Remote: Command not allowed)
If yes How?
Because i am also in same problem...:crying::crying::crying:
Revert to stock OS, then go to Developer settings and enable OEM unlock.
Then repeat hte process.
How can I get the stock OS without TWRP? I tryed dload method, but theres is allways a problem when eRecovery tries to install the update.zip... Idon't know what to do.. My bluetooth is not working, that my problem