NOTE: I don't have a TP anymore, but i am pretty sure the installation instructions will be the same moving forward. If you are new follow the full guide, if you are already on one of the CM versions, skip to step 7 and replace the file with the current file.
Note: If you are already on CM Alpha 1/2.1 skip to step 7, if not you can follow the instructions below to install CM Alpha 3 from WebOS.
Alright, here is a step by step instruction on how to install CM Alpha 3 on Touchpad. I did notice there is a video guide but a text step by step might be useful for some. I have this installed and for Alpha release this is fantastic.
Pretty straightforward installation, but as always you follow this guide and flash at your own risk. Main thread for the CM port is here. Read whats working and whats not working there. If you have any questions, post it there. but read the known issues first, don't post know issues. This is just a guide.
Required:
1) PC ( windows, mac or linux) with working Internet
2) HP Touchpad ( obviously) and the usb cable that came with it.
3) Good Reading skills ( I am serious).
4) Read this guide twice if you have to.
Step 0:
Get your pre flash jitters out and think twice. This will root your device and hence your warranty will be void after the flash. If you still want to flash, back up your current HP touchpad. figure out which way is your volume up button ( you will need for step 4) and proceed to step 1
Step 1:
Make sure you have atleast 2GB of free space in your touchpad. Download the following files from here
1)Moboot bootloader for multi boot
2)CM Alpha 3
3)Clockwork Mod Recovery
Once done, go to step 2 below;
Step 2:
1)Acme Installer from here
2) HP WebOS SDK for windows, mac or linux
3) Follow the links above to install the full SDK or just the Novacom driver which is all that is required. If you are not sure, install the full sdk.
on to step 3 now.
Step 3:
1) Connect Touchpad to PC with the usb cable that came with it and select Usb Drive option.
2) Once the Touchpad pops up on your screen, create a folder called cminstall and put the files you downloaded in Step 1 there.
3) Eject/Safely remove touchpad from the pc, remove the USB cable from pc and shutdown touchpad, then go to step 4.
Step 4:
1) Do you know which way is your volume up button? if you are not sure then you are not paying attention to this guide. To figure out which way, boot to webOS, figure it out and shutdown.
2)Hold the volume up button and press power button simultaneously. You should see a white USB symbol.
3)Connect the USB cable back to pc and if the Novacom drivers were properly installed, the driver will be automatically detected and installed.
Step 5:
Almost there, time to install now.
Extract the Acme Installer you downloaded in Step 2 to your desktop or wherever you want. Open up cmd ( in windows) or terminal ( in linux or mac). cd to the directory where you just extracted your Acme Installer.zip and go to step 6 for install.
Step 6:
Now type this in the command prompt after you have done cd
novacom boot mem:// < ACMEInstaller
NOTE: windows users might have to manually move the novacom.exe and/or AcmeInstaller into c:\programfiles\palm folder and run the above command from there.
and wait for it to install and boot into CyanogenMod. If your clockwork mod didn't get installed, go here for a fix.
Step 7:
Update from CM Alpha 1/ 2.1
1) Download CM Alpha 3 from here
2) Plug in your touchpad to PC, select copy usb files option
3) Transfer CM Alpha 3 zip file into the "sd card" of your touchpad when it pops up and disconnect.
4) Long press power button and select reboot, then recovery option.
5) Recommended but Optional ( I didn't): In CWM recovery, go to backup and storage, do a nandroid backup before updating, back to main cwm recovery, wipe cache and in advanced wipe dalvik cache.
6) In the CWM recovery meny, use your volume buttons and select install zip file from sd card, select zip file and select cm alpha 3 zip, then scroll down and say yes.
7) Reboot. To check if you are on alpha 3, go to settings, about tablet and mod version should be alpha3.
To install google market and google apps, go here
Have Fun. Thanks to the awesome CM team, we have android on touchpad.
NOTE: If you want to uninstall CM for whatever reason, download ACME uninstaller from here and run it like you did with ACME installer. This should work ( i haven't tried it though).
SOD( Sleep of Death): This is when touchpad goes to sleep and wouldn't wake up, don't panic. Doesn't happen often and I have never seen it since installing Alpha 2.1. Press and hold power and home button for 10 - 20 secs and your TP will reboot. One fix for this is to use no-frills cpu control or set cpu and set min cpu to 384Mhz.
sticky this!
Good effort but you're going to get warned/banned by the mods for cross linking. They have to protect their domain you know.
techspecs said:
Good effort but you're going to get warned/banned by the mods for cross linking. They have to protect their domain you know.
Click to expand...
Click to collapse
Cross linking? I linked directly to the other websites which host the files. Thats not allowed? If so, mods can delete this thread. Only trying to help. I don't see another thread for a guide here in this section unless i am blind .
I've followed all the steps exactly and I'm getting this:
The ACME files were extracted to my users folder.
RavenSEAL said:
I've followed all the steps exactly and I'm getting this:
The ACME files were extracted to my users folder.
Click to expand...
Click to collapse
Looks like novacom wasn't installed properly. I don't have windows, so hopefully somebody else can chime in. try reinstalling novacom or the entire sdk.
Sent from my HP Touchpad using xda premium
reinstall and a quick reboot on my PC did the trick , running CM7 now
RavenSEAL said:
reinstall and a quick reboot on my PC did the trick , running CM7 now
Click to expand...
Click to collapse
Glad you got it sorted out. Enjoy cm
Sent from my HP Touchpad using xda premium
Android is unable to establish a reliable data connection to verify your google account :|
I am getting the same error:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Users\Damian>cd c:\Users\Damian\desktop
c:\Users\Damian\Desktop>novacom boot mem:// < ACMEInstaller
'novacom' is not recognized as an internal or external command,
operable program or batch file.
c:\Users\Damian\Desktop> novacom boot mem:// < ACMEInstaller
'novacom' is not recognized as an internal or external command,
operable program or batch file.
c:\Users\Damian\Desktop>Acmeinstaller
'Acmeinstaller' is not recognized as an internal or external command,
operable program or batch file.
c:\Users\Damian\Desktop>novacom boot mem:// < ACMEInstaller
'novacom' is not recognized as an internal or external command,
operable program or batch file.
c:\Users\Damian\Desktop>novacom boot mem:// < ACMEInstaller
'novacom' is not recognized as an internal or external command,
operable program or batch file.
c:\Users\Damian\Desktop>
I reinstalled Novacom and in device manager it's there and installed correctly.
Breakthecycle2 said:
I am getting the same error:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Users\Damian>cd c:\Users\Damian\desktop
c:\Users\Damian\Desktop>novacom boot mem:// < ACMEInstaller
'novacom' is not recognized as an internal or external command,
operable program or batch file.
c:\Users\Damian\Desktop> novacom boot mem:// < ACMEInstaller
'novacom' is not recognized as an internal or external command,
operable program or batch file.
c:\Users\Damian\Desktop>Acmeinstaller
'Acmeinstaller' is not recognized as an internal or external command,
operable program or batch file.
c:\Users\Damian\Desktop>novacom boot mem:// < ACMEInstaller
'novacom' is not recognized as an internal or external command,
operable program or batch file.
c:\Users\Damian\Desktop>novacom boot mem:// < ACMEInstaller
'novacom' is not recognized as an internal or external command,
operable program or batch file.
c:\Users\Damian\Desktop>
I reinstalled Novacom and in device manager it's there and installed correctly.
Click to expand...
Click to collapse
Sorry, are you saying when you reinstalled novacom everything worked? if not try moving ACME installer to the novacom directory and try from there.
Any idea where they would be? I can't find them.
---------- Post added at 04:48 PM ---------- Previous post was at 04:39 PM ----------
That didnt work either.
Breakthecycle2 said:
Any idea where they would be? I can't find them.
---------- Post added at 04:48 PM ---------- Previous post was at 04:39 PM ----------
That didnt work either.
Click to expand...
Click to collapse
try running cmd prompt as an admin. I don't have a windows machine, so i am not sure whats happening with yours. you have xp or windows 7 or vista?
Breakthecycle2 said:
Any idea where they would be? I can't find them.
---------- Post added at 04:48 PM ---------- Previous post was at 04:39 PM ----------
That didnt work either.
Click to expand...
Click to collapse
I had problems running it from desktop as well. got the same message you did. tried running it as admin and from c:\ to no avail. put acme in C:\Program Files\Palm, Inc\ directory and it worked finally
I got it! Thanks!
Breakthecycle2 said:
I got it! Thanks!
Click to expand...
Click to collapse
it worked for you by putting it in the palm folder like the poster above yours said? if not please post your soln for other windows users benefit. thanks
im having problems within cmd, i get access denied anytime i run the novacom command, i also ran under an admin account and as administrator n have the same problem, i tried under safe mode and it couldnt connect to server so what do i do?
I am using a laptop using ubuntu 11.04 lts. I follow all of the steps 100% and yet when i do the novacom prompt in terminal it boots my touchpad yet never goes to the penguin screens or installs anything. It just stays on the HP logo untill i do the manual reboot by holding home and power. Any ideas?
rizdog23 said:
I am using a laptop using ubuntu 11.04 lts. I follow all of the steps 100% and yet when i do the novacom prompt in terminal it boots my touchpad yet never goes to the penguin screens or installs anything. It just stays on the HP logo untill i do the manual reboot by holding home and power. Any ideas?
Click to expand...
Click to collapse
did you install the sdk and the novacom driver like the linux link suggested? i have ubuntu 11.04 and the steps i described worked no problems. reinstall novacom drivers
i installed the driver but not the full sdk cuz i was told i did not need to. Can you maybe give me a break down of how things will look like on ubuntu strictly? Sorry if i seem like a noob or it is bothersome for you to have to reply. I greatly appreciate your help
Related
MANY THANKS TO REV FOR RE-WRITING THIS FOR ME!
(Post was updated on 3/23/2011)
=======================================
This post is to provide a template for using NVFlash to restore/recover your G-Tablet after suffering some kind of malfunction. Specifically, this document tries to provide ALL the information you need to use the NVFlash tool to recover the bekit 1105 software version, which has been found to be safe as a starting point for rebuilding your tablet after having a problem. This post does not include other methods of setting up NVFlash (such as installing the SDK, etc.) because this method is proven and can be easily supported.
I use Ubuntu Linux and know that the Linux instructions below are correct. Others have written Windows instructions and those too have been checked carefully and have been used before successfully.
A WARNING IN ADVANCE: NVFlash makes changes to the partition structure of your device. You should tread carefully and understand the risks. (MOD EDIT Note: It also has been noted a bunch of times that even NVFlashing your G-Tablet will not completely overwrite everything on it.)
The NVFlash setup process begins with a visit to:
http://db.tt/Wm25t7U
(Note: Sometime this DropBox is cranky. If you have trouble with it, check back later.)
Linux users: You want to get "nvflash_linux_2010110500.tar.gz" and "nvflash_gtablet_2010110500.zip "
Windows users: You want to get "nvflash_windows_20100500.zip" and ""nvflash_gtablet_2010110500.zip"
Note: The above "nvflash_gtablet_2010110500" is commonly referred to as bekit version 1105 in many posts relating to nvflashing (especially my posts).
-------------------------------------------
Installation
First, create a folder named "NVFlash" on your PC to put the needed files into and to work from. (Note: You can call it something else if you want to; we're just using "NVFlash" to keep all of us on the same page.)
Next, extract the files you downloaded from the DropBox above into the "NVFlash" directory. The files with linux and windows in the middle of then are the files for setting up NVFlash. (The are taken from the SDK and do not install the whole SDK -- just a simple, operable NVFlash for us to use here.) The files with gTablet in the middle contains the .img files with the software to go on your G-Tablet.
Third, for Windows users, you'll need to have an APX-specific USB driver for the next steps. (The Windows package bekit supplied has an .inf file in it, but the actual drivers are not there). For Linux users, you don't need an extra driver.
One source for the Windows drivers is at
http://www.myadventvega.co.uk/
Find the "Downloads" tab in the middle of the page and click on "USB System Driver" to get the files. Extract them and go down two levels to the "USB" folder -- and move that into your "NVFlash" directory. The USB folder has the .inf file for installation in it along with two other directories with drivers for the various operating systems. (Note: These drivers, which are the same as the drivers in the SDK, are proven to work with Win 7 64-bit and have the setup include to load into other versions of Windows.) Follow this narrative for actual installation of the drivers.
CHECKPOINT: At this point, you should have the nvflash files, .img files, and USB directory (and files) in you "NVFlash" directory and are ready to begin the recovery process.
Now, you will need to boot into G-Tablet APX mode: hold down the power and volume - button simultaneousl until your G-Tab comes up and the goes back to a black screen. The black screen means it is in APX mode and it is waiting to display the flashing process. In Linux, type "lsusb" in a terminal and you should see this "0955:7820 NVidia Corp.". 7820 means the device is in APX mode.
Connect your G-Tablet to your PC using your miniUSB to USB cable that came with your tablet.
Linux users: At this point, open up a command window to the folder you created, and run this script:
./nvflash_gtablet.sh
This will wipe the device back to bekit's original TnT stock image, except for user data which is retained. Should take about a minute to run and the device will reboot itself automatically. If the script does not work, make sure that the shell script and nvflash binary are set as executables.
Windows users: When you connect to the PC, the PC immediately tries to load a driver -- but since it doesn't know where the USB driver files are it will fail. Click through Start/Control Panel/Device Manager and find "APX" listed in the devices with a yellow "!" (exclamation point) on the icon. Select the APX item and find the "Update Driver" button and click it. When it asks where to search, choose the local computer manual selection choice and tell it to Browse.
Point the Browse (and the USB install) at the "USB" directory under the "NVFlash" folder. When pointed at the "USB" directory, the driver installed and I was ready to nvflash. If you go back to Device Manager after the Windows install has completed, it will show the nVidia USB drivers near the top of the USB device list.
Again, for Windows: Run this script which is in the "NVFlash" folder:
nvflash_gtablet.bat
This will wipe the device back to bekit's original TnT stock image except for user data, which is retained. Should take about a minute to run and the device will reboot itself automatically all the way to the main screen.
POST NVFlash:
When your G-Tablet has booted back to the main screen, you will have to check and make sure everything is set up. Particularly, get the wifi on and connected to the Internet. Almost immediately, you should get a notice about an OTA (over the air) update. This is the OTA Update to software version 3588. If it does, go ahead and have it do the update. From there, you can begin using your "stock 3588" G-Tablet.
If you don't get an automatic OTA notification, you can go the to manual "Update" icon on your tablet and have it check for updates -- and hopefully it will find OTA 3588.
Or, if neither of the above happen, you can download 3588 at the following link and install it manually:
http://tapntap.http.internapcdn.net/tapntap/viewsonic/update-smb_a1002-3588-user.zip
Note: Following is a STICKY from General Forum on the stock recovery process:
http://forum.xda-developers.com/showthread.php?t=892090
NOTICE: There are many threads out there with tell how to do this process. Others tell individuals' problem solving experiences. A few of them may not be right! The above process is not the only way to do this -- but it is fairly straightforward and it is proven. It is recommended for anyone who does not have experience with nvflashing.
***************************************************
Further references (since I'm not a Windows user): http://forum.xda-developers.com/show...0&postcount=28
and http://forum.tegratab.com/viewtopic....bbde76184e550a and http://wiki.tegratab.com/index.php/Nvflash_FAQ
An additional suggestion if you also want to tack on bekit's clockworkmod recovery versus standard recovery: http://forum.xda-developers.com/show...3&postcount=17
Hope this helps!
03/2011 update -- I've been told that this tool has been useful to erase ALL partitions, including user data. I believe you need to re-flash with the bekit 1105 above, AFTER you use this: http://forum.xda-developers.com/showthread.php?t=974422
04/22/2011 update -- I've built out both 1.1-3588-based and 1.2-4349-based versions that have effectively replaced bekit's 1105 image ("nvflash_gtablet_2010110500.zip"), at least on my own device - I'm also addding a clockworkmod recovery option. It is being hosted in the same location as my 1.2-based mods - I will be making updates there, from this point on (as I might update them from time to time).
(you'd still need bekit's Windows or Linux tools, keep in mind) I've been able to bring back my device back from a soft-brick several times, so I feel they are usable.
05/09/2011 update -- A reminder that these images are not being updated, here. I have a newer nvflash post over in the same site where I have my 1.2-based mods. The 1105 bekit image mentioned here is still relevant for 1.1-based ROM users, or you can use my 3588 ot 4349 solution at the other site.
05/10/2011 update -- I have PM'd the moderator to either unsticky this post and / or assign it to someone else, as I do not plan on updating it, here. I believe that there is a 3588 image in the TegraTab IRC that someone created, for example.
Looks good Roebeet. I wrote a little how to a while back on tegratab. I know you are aware but for the benefit of others I wanted to add the following.
One little thing is sometimes when you are done you will get a boot loop. I think it only may happen once as I never saw it again. The fix is to go into Clockwork and partition the internal sd card again. The old settings said 512 for memory, and 256 swap. Bekit updated Clockwork and now you can format all the way to 4gb if you like, and swap should be 0 as it is not used.
Edit: New wisdom says not to partition the internal sdcard to anything but 2048. Folks have had issues with memory errors in the market with anything bigger. 0 for a swap is also the recommendation as Android apparently does not make use of the swap.
roebeet said:
Wanted to expand on what was already here, since there seems to be a lot of questions that pop up. I use Ubuntu so I know that the Linux instructions are correct.
A warning in advance: nvflash makes changes to the partition structure of your device. You should tread carefully and understand the risks.
Pre-req: http://db.tt/Wm25t7U
Linux users: You want to get "nvflash_linux_2010110500.tar.gz" and "nvflash_gtablet_2010110500.zip "
Windows users: You want to get "nvflash_windows_20100500.zip" and ""nvflash_gtablet_2010110500.zip"
Other references (since I'm not a Windows user): http://forum.xda-developers.com/showpost.php?p=9564270&postcount=28
and http://forum.tegratab.com/viewtopic.php?f=6&t=8&sid=4e6bd75cda9e24e04fbbde76184e550a
http://wiki.tegratab.com/index.php/Nvflash_FAQ
-------------------------------------------
Installation
Create a folder on your PC which you use as your restore base, and then extract the platform-specific ZIP into that location.
Then, download the "nvflash_gtablet_2010110500.zip" package and unzip the /nvflash_gtablet/ folder inside into the same folder as where you dropped nvflash.
For Windows users, you'll need to have an APX-specific USB driver for the next steps (I believe that the Windows package bekit supplied has that .inf file, but again I don't know for sure). For Linux users, you don't need an extra driver.
Once ready, boot the device into APX mode (power up and volume down, at the same time - you'll see the boot screen pop up, and then go blank.). In Linux, type "lsusb" in a terminal and you should see this "0955:7820 NVidia Corp.". 7820 means the device is in APX mode.
Linux users: At this point, open up a command window to the folder you created, and run this script:
nvflash_gtablet.sh
This will wipe the device back to bekit's original TnT stock image, except for user data which is retained. Should take about a minute to run and the device will reboot itself automatically.
Windows users: (again, I did not test this myself). Run this script, in the folder you created:
nvflash_gtablet.bat
Hope this helps!
Click to expand...
Click to collapse
I need help. I finally got Windows 7 to recognize the device in APX mode but how do I flash from this point. It only shows up in my Device list with all the subfolders in it.
What is this for? Restoring to factory Rom?
Thanks,
Scott
cscotty said:
What is this for? Restoring to factory Rom?
Thanks,
Scott
Click to expand...
Click to collapse
Yes, you can use it for exactly that. I believe bekit added Launcher Pro and superuser, but other than that it's a way to completely wipe the device. Moreso than a standard recovery would do.
The pre-req link doesnt work. Can you update the link?
Thanks
roebeet said:
Wanted to expand on what was already here, since there seems to be a lot of questions that pop up. I use Ubuntu so I know that the Linux instructions are correct.
A warning in advance: nvflash makes changes to the partition structure of your device. You should tread carefully and understand the risks.
Pre-req: http://db.tt/Wm25t7U
Linux users: You want to get "nvflash_linux_2010110500.tar.gz" and "nvflash_gtablet_2010110500.zip "
Windows users: You want to get "nvflash_windows_20100500.zip" and ""nvflash_gtablet_2010110500.zip"
Other references (since I'm not a Windows user): http://forum.xda-developers.com/showpost.php?p=9564270&postcount=28
and http://forum.tegratab.com/viewtopic.php?f=6&t=8&sid=4e6bd75cda9e24e04fbbde76184e550a
http://wiki.tegratab.com/index.php/Nvflash_FAQ
-------------------------------------------
Installation
Create a folder on your PC which you use as your restore base, and then extract the platform-specific ZIP into that location.
Then, download the "nvflash_gtablet_2010110500.zip" package and unzip the /nvflash_gtablet/ folder inside into the same folder as where you dropped nvflash.
For Windows users, you'll need to have an APX-specific USB driver for the next steps (I believe that the Windows package bekit supplied has that .inf file, but again I don't know for sure). For Linux users, you don't need an extra driver.
Once ready, boot the device into APX mode (power up and volume down, at the same time - you'll see the boot screen pop up, and then go blank.). In Linux, type "lsusb" in a terminal and you should see this "0955:7820 NVidia Corp.". 7820 means the device is in APX mode.
Linux users: At this point, open up a command window to the folder you created, and run this script:
nvflash_gtablet.sh
This will wipe the device back to bekit's original TnT stock image, except for user data which is retained. Should take about a minute to run and the device will reboot itself automatically.
Windows users: (again, I did not test this myself). Run this script, in the folder you created:
nvflash_gtablet.bat
Hope this helps!
Click to expand...
Click to collapse
stanglx said:
The pre-req link doesnt work. Can you update the link?
Thanks
Click to expand...
Click to collapse
It seems to go up and down (it's bekit's dropbox). Try this:
https://www.dropbox.com/s/wrcd87u1iy31u4e
roebeet said:
Wanted to expand on what was already here, since there seems to be a lot of questions that pop up. I use Ubuntu so I know that the Linux instructions are correct.
A warning in advance: nvflash makes changes to the partition structure of your device. You should tread carefully and understand the risks.
Pre-req: http://db.tt/Wm25t7U
Linux users: You want to get "nvflash_linux_2010110500.tar.gz" and "nvflash_gtablet_2010110500.zip "
Windows users: You want to get "nvflash_windows_20100500.zip" and ""nvflash_gtablet_2010110500.zip"
Other references (since I'm not a Windows user): http://forum.xda-developers.com/showpost.php?p=9564270&postcount=28
and http://forum.tegratab.com/viewtopic.php?f=6&t=8&sid=4e6bd75cda9e24e04fbbde76184e550a
http://wiki.tegratab.com/index.php/Nvflash_FAQ
-------------------------------------------
Installation
Create a folder on your PC which you use as your restore base, and then extract the platform-specific ZIP into that location.
Then, download the "nvflash_gtablet_2010110500.zip" package and unzip the /nvflash_gtablet/ folder inside into the same folder as where you dropped nvflash.
For Windows users, you'll need to have an APX-specific USB driver for the next steps (I believe that the Windows package bekit supplied has that .inf file, but again I don't know for sure). For Linux users, you don't need an extra driver.
Once ready, boot the device into APX mode (power up and volume down, at the same time - you'll see the boot screen pop up, and then go blank.). In Linux, type "lsusb" in a terminal and you should see this "0955:7820 NVidia Corp.". 7820 means the device is in APX mode.
Linux users: At this point, open up a command window to the folder you created, and run this script:
nvflash_gtablet.sh
This will wipe the device back to bekit's original TnT stock image, except for user data which is retained. Should take about a minute to run and the device will reboot itself automatically.
Windows users: (again, I did not test this myself). Run this script, in the folder you created:
nvflash_gtablet.bat
Hope this helps!
Click to expand...
Click to collapse
Roebeet sorry but I just noticed for noobs that the linux command needs to be
. nvflash_gtablet.sh
Also if you unzip those files into a premade directory such as "gtablet" when you unzip them each have their own directories and if you ls you can see that the bash script isn't executable from there. So you need to copy either the gtablet files into the platform folders or copy all the files inside both into your "gtablet" folder. Then you can run the ". nvflash_gtablet.sh" command and voila. Sorry I am on Ubuntu and don't know if it is different, but that is the way I run them.
No worries - all replies are welcome! the more info we have, the better.
This should be stickied. Nvflash has saved my gtab many times and I think its the reason why my gtab doesn't really encounter too many Force closes. Its the perfect method to ensure your gtab is clean.
I tried this tonight to try to get my gTablet back to stock so that I could show people how to install CWM on a video but I could get neither of my Windows 7 64-bit computers to recognize the APX .inf that was included in the pack.
I have a linux machine around here somewhere I may have to use...
ehunyadi said:
I tried this tonight to try to get my gTablet back to stock so that I could show people how to install CWM on a video but I could get neither of my Windows 7 64-bit computers to recognize the APX .inf that was included in the pack.
I have a linux machine around here somewhere I may have to use...
Click to expand...
Click to collapse
My limited experience with 64-bit Win7 -- the drivers have to be signed, or else they won't work. There's a way to disable that on boot, but you can't permanently disable it. I'm wondering if the APX USB driver is signed?
Open a command prompt as an admin and type
bcdedit -set loadoptions DISABLE_INTEGRITY_CHECKS
bcdedit -set TESTSIGNING ON
This is the only way.. dont worry if the test watermark shows up.. it wont affect anything.
Also... They have a x64 driver - read this
http://tegradeveloper.nvidia.com/tegra/forum/adb-usb-driver
Hi there,
I exchanged for a new Gtab yesterday from sears (as it had some power issues).
Today, I tried TnT 2.2 on my rooted tab (Z4 for rooting). Also have ClockworkMod .8.
I partitioned my internal SDCard. But after vanilla restore, I could find my tab space reduced to 4 gigs. What should I do to restore to full 16 gigs(14+ gigs actually).
============================================================================================================================
2. I followed your instrction and partitioned again in clockworkMod and did 4 gigs and 0 in the second one. Now it shows 11 gigs for data and 4 gigs for system.
Now I inserted an external micro SD card (16 gigs) but my storage is not seeing it. What should i do? Ignore my first part please.
Your gonna have problems later if you don't repartition to 2048 and 0
satishraman said:
Hi there,
I exchanged for a new Gtab yesterday from sears (as it had some power issues).
Today, I tried TnT 2.2 on my rooted tab (Z4 for rooting). Also have ClockworkMod .8.
I partitioned my internal SDCard. But after vanilla restore, I could find my tab space reduced to 4 gigs. What should I do to restore to full 16 gigs(14+ gigs actually).
============================================================================================================================
2. I followed your instrction and partitioned again in clockworkMod and did 4 gigs and 0 in the second one. Now it shows 11 gigs for data and 4 gigs for system.
Now I inserted an external micro SD card (16 gigs) but my storage is not seeing it. What should i do? Ignore my first part please.
Click to expand...
Click to collapse
You only have 16gb to start. Partitioning you internal to 4gb uses part of that. I would go back and only use 2gb, and 0 for swap. There are things, like the new market that break with anything but 2gb.
If you mean the settings menu is not showing your external sd card that's normal. Look in a file explorer program in the / directory. Look for SDcard2. That is your external. Same deal, look for usbdisk if you plug in a usb drive.
Roebeet
also this could be helpful to Ubuntu/linux users.
in the same directory where your flash script is there is a file that is called "gtablet.cfg" if you download the clockwork.img recovery and put it in this directory you can open up the "gtablet.cfg" with a text editor
scroll down to where you see "filename=part9.img" and replace "part9" with "clockwork" and it should now read "filename=clockwork.img" this will flash clockwork and save you a step. To change it back so you flash complete stock just edit the file again and reverse it.
romanrish said:
Roebeet
also this could be helpful to Ubuntu/linux users.
in the same directory where your flash script is there is a file that is called "gtablet.cfg" if you download the clockwork.img recovery and put it in this directory you can open up the "gtablet.cfg" with a text editor
scroll down to where you see "filename=part9.img" and replace "part9" with "clockwork" and it should now read "filename=clockwork.img" this will flash clockwork and save you a step. To change it back so you flash complete stock just edit the file again and reverse it.
Click to expand...
Click to collapse
You don't even have to do that - you can just rename part9.img to something else, and clockworkmod.img to "part9.img". That's actually what I do.
roebeet said:
You don't even have to do that - you can just rename part9.img to something else, and clockworkmod.img to "part9.img". That's actually what I do.
Click to expand...
Click to collapse
Yeah I thought about that, but figured some people might get confused and forget which one was which. Either way works as well just as long as you keep both files. You should edit your original post and add that in as an option to do at the end. It will keep some from having to look through and creating a new post cause they can't find it, and keep our forums clean.
This should definitely be stickied. Mods please?
P.S. I cannot believe how awesome this forum is(Viewsonic G Tablet). I have gone to other forums and the other devs and users are not as friendly and awesome as the ones we have here. Almost brings a tear to my eye. Great job Roebeet, this should help us noobs out a lot. LOL!
OUTDATED[Guide] Setting up/using adb/fastboot-unlock, flash custom recovery & root
Below is a great guide to rooting, from several sources, (mostly taken from pingvinen's "An Idiot's Guide to Flashing the Xoom" and a guide by publicanimal. and I hope it helps. You can find the links to all of the files referenced below in the Xoom Heaven thread (thanks StrifeSoldierVII!)[/I]
(New thread in General Section by Jack207407 will have all the updated links for flashing
http://forum.xda-developers.com/showthread.php?t=1443110
One Stop For ROM's, MOD's, and Root Wifi-Only and 3G/4G Models)
"What you need to do can be encompassed in these following short steps (will be detailed later on) in the following order. Each step is required before you can proceed to the next one. However, make sure that you are very very careful and don't try to take any shortcuts. That may soft-brick your device, and you may have a difficult time to explain that to your wife ... You have been warned.
HERE'S THE USUAL DISCLAIMER--I AM NOT RESPONSIBLE FOR ANY HARM THAT MAY COME TO YOUR DEVICE IF YOU FOLLOW ANY PART OF THIS GUIDE--ANY RISK IS ON THE USER!
I strongly recommend you to read the entire guide before trying. In fact, read it twice to ensure that you have understood everything. If there is weird stuff that you don't understand, don't hesitate to ask. The reason for me writing this down is that I like to document what I have learned. This is to me an excellent way to ensure that I will remember what I just did. Another reason was that I could not find a single thread that encompassed all steps required. There are many different threads, but no one (that I could find) that really guides you from start to goal. So enjoy and good luck!
I would like to thank LandMaster and cam30era for helping out with advice during my initial trail-and-error session. I soft-bricked my device once and had big problems to get by point 4.3 (avoid overwriting of CWM), but with their encouragement I finally succeeded.
Just a note before we begin: the different Xoom. Models that are able to use this guide are the following:
MZ600 - stingray_cdma - Motorola US 3g Xoom (technically this device is stingray as well, but I will be using stingray_cdma as the two devices have incompatible software)
MZ601 - utms_everest - Motorola EU 3g Xoom
MZ602 - stingray - Motorola US 4g Xoom
MZ604 - wingray - Motorola Wifi Xoom
(thanks solarnz!)
___________
Overview of the 6 required steps
1. Install Motorola USB drivers for your computers (for USB connectivity) 2. Install Java SDK and Android SDK tools (for adb and fastboot commands) 3. Unlock the device for flashing (allowing replacement of recovery and boot images) 4. Install a modified recovery image (ClockWorkMod recovery for Android) 5. Root the device (Allow r/w access to the device filesystem) 6. Flash a kernel that supports overclocking etc.
Steps 1, 2, 4, 5 and 6 require that you download install, image and zip files needed for the flashing.
All this was performed on a Windows PC. Windows 7, Mac and Linux users will probably have to do some steps differently.
1.0 Install the latest Motorola USB drivers
The installation file can be found at: http://developer.motorola.com/docstools/USB_Drivers/
1.1 Install the drivers and ensure that your Xoom is recognized by the computer
2.0 Installation of development software
Android SDK and Java SDK need to be installed. You can find the installation kits here.
http://developer.android.com/sdk/index.html In case you can't find fastboot.exe, look for it here (thanks to jerrycycle): http://forum.xda-developers.com/showpost.php?p=19546334&postcount=5
Update: you could also just install the adb fastboot pack here:http://www.android.net/forum/downloads.php?do=file&id=67
http://www.oracle.com/technetwork/java/javase/downloads/index.html
2.1 Install them as any other software, making an Android SDK folder on C/.
2.2 Make sure that all the files you need are in the Platform Tools folder (fastboot, recovery image file and so on). Copy any files in the Tools folder to the Platform Tools folder if necessary. Note: If the Android SDK complains that the Java Dev Kit can't be found, just press Back and then Next again. Wierd, but that seems to do the trick ... go figure.
(Warning: Never put any zip files in your Platform Tools folder. Flashing zip files through fastboot will cause very serious problems. Zip files must be flashed from the external micro SD card through CWM recovery on the Xoom...we'll get to that later.)
2.3 Test that ADB and FASTBOOT works. You should open a command window by right clicking in your Platform Tools folder where all of your files are, plug in your Xoom to your computer with your Motorola cable (it may not work with a generic cable) and write 'adb devices'. Your Xoom should now be listed. Did your device not show up? Make sure that you have USB debugging enabled in Settings/Applications/Development on your Xoom.
Optional: Those that want to be able to access adb from any where on their computer, here's a tip from scsa20: "For windows, if you go into System Properties and choose Advanced, then Environment Variables..., you'll be able to edit the Path variable under System variables, just add the path to where adb and fastboot is located (separated with a semi-colon ().
Here's what my Path variable looks like:
C:\Program Files\Common Files\Microsoft Shared\Windows Live;C:\Program Files (x86)\Common Files\Microsoft Shared\Windows Live;C:\Program Files (x86)\NVIDIA Corporation\PhysX\Common;%SystemRoot%\system32;%Sy stemRoot%;%SystemRoot%\System32\Wbem;%SYSTEMROOT%\ System32\WindowsPowerShell\v1.0\;C:\Program Files (x86)\Windows Live\Shared;c:\Program Files (x86)\Microsoft SQL Server\100\Tools\Binn\;c:\Program Files\Microsoft SQL Server\100\Tools\Binn\;c:\Program Files\Microsoft SQL Server\100\DTS\Binn\;C:\android-sdk-windows\tools;C:\android-sdk-windows\platform-tools;C:\Program Files (x86)\Common Files\Acronis\SnapAPI\
It's long but do you see the android stuff there at the end?"
Update: xda poster Mandelbrot Benoit suggests an alternate adb setup, here: http://forum.xda-developers.com/showpost.php?p=18072572&postcount=50
If your windows computer doesn't see your Xoom, consider this (Originally Posted by AngryBulleteyeTruth):
When the xoom does not show up on PC it may be the problem of.... windows media player!
Xoom uses drivers of WMP to communicate with PC. If someone does not have the newest WMP drivers it will not show up and you can see xoom device in the devices tab on PC having an exclamation mark.
So the solution is to download and install Windows Media Player 11. It has worked for me.
--------
OK. Now that you are set up, it's Showtime! Take a deep breath...
3. Unlocking the device for flashing
This step will effectively erase the internal storage, including all your apps and settings. Use whatever backup you want to secure important data before you start. (It will also void your warranty, so you still have time to go back.)
3.1 Power up and start the Xoom.
3.2 Ensure that your device is fully recognized by the computer. A good sign is that the 'Portable device' dialog is activated on Windows when your Xoom has booted. The Xoom should also be seen in 'Computer'. If not, go back to step 2 and double check your USB drivers.
3.3 Use the command 'adb reboot bootloader' to go into Flash mode.
3.4 Use the command 'fastboot oem unlock'. This will trigger a dialog on your Xoom. Follow the instructions on the screen to complete the unlocking. I repeat, this *will* do a factory reset and all data will be lost!
3.5 Once unlocked, the Xoom will restart and work as normal. Don't bother to do any setup at this time, just make sure that USB debbuging is checked in settings, and now go on to step 4
4. Install recovery image (CWM) UPDATED 4/19/12
If you haven't done it already, download the recovery image file and save it to your computer in the Platform Tools folder.
(Download the recovery image from this link: http://forum.xda-developers.com/showthread.php?t=1604014 only the img file flashed through fastboot Remember, never try to flash a zip file through fastboot!)
Important: At this time, make sure you have a good (known to be working) microsd card in your sdcard slot in your Xoom. Reboot the Xoom with the sdcard in the slot to make sure it's mounted.
4.1 Boot into flash mode with 'adb reboot bootloader.'
4.2 Install your downloaded recovery image: 'fastboot flash recovery eos-recovery-r6.img' or whatever is the exact name of the recovery img file you are flashing.
4.3 Enter CWM recovery with the procedure below.
4.4 Restart the device with 'fastboot reboot'. Timing is essential here, so be alert when the device restarts, or you will have to redo section 4.
4.5 Once the Motorola logotype is shown, start counting to 3. At 3, press the Volume Down button. This should result in the text 'Android Recovery' in the top left corner. If it does not work (if you see Starting Fastboot Protocol), experiment with the timing (see below).
4.6 When 'Android Recovery' is shown press the Volume Up button. This should invoke the CWM recovery menu. If that works, then congratulations for getting this far!
Here is a potential pitfall. If you are unable to enter CWM *before* the device boots into Honeycomb, then the newly installed recovery image will be overwritten by the system default recovery. Just repeat steps 4.1 through 4.6 if that happens.
UPDATE(12/28/11) Since putting this guide together, Motorola has issued a number of Over-the-Air (OTA) updates that have complicated the process of flashing the Clockawork Mod recovery, so if you have accepted any OTA updates, please read the following, which describes each step (http://forum.xda-developers.com/showthread.php?p=26009191#post26008083) (Thanks to Landorin.)
(If you have root and want to remove these files, remove or rename /system/etc/install-recovery.sh with something like root explorer. You can then flash your custom recovery through fastboot again.)
For those of you that get stuck with some error like 'device not recognized' poster Madjinj gives the following advice:
1) Be sure that you have your adb folder in the root of C drive directly and be sure that you are in adb folder in command prompt program (CMD in Windows machines) i.e by typing "cd c:\XXX" where XXX is the name of adb folder in your machine.
2) Be sure that you type "adb reboot bootloader" in comand prompt to activate adb program. if the problem persists, try typing "fastboot reboot" then after reboot type "adb reboot bootloader" in command prompt program.
3) Use the USB cable that came with your Xoom (some cables are not good in flashing for unknown reason..!!
4) make sure that you activate USB debugging mode.
5.0. Rooting the Xoom
The Universal Xoom Root zip file from solarnz is located here: http://forum.xda-developers.com/showthread.php?t=1242241
5.1 You need to transfer the Universal Xoom Root zip file to a working external micro SD card. You can do this on a computer or cell phone, but the Universal Xoom Root zip file must be located in the root directory of the micro SD card.
5.2 Insert the now prepared SD card in the Xoom.
5.3 Boot into recovery (as described in 4.3). Navigate using the volume buttons and press the power button to select the active option.
5.4 Select 'Install ZIP from sd card.'
5.5 Select 'Choose ZIP.'
5.6 Navigate to the ROOT zip file with the Volume buttons and select it with the Power button. Confirm that you want to install it.
5.7 Everything should indicate success, so back out to the main CWM menu and reboot the device.
5.8 From Android Market, install any app requiring root and start it. If the rooting was successful, then the app should request superuser permission and you should be able to grant it without any problems.
6. Flashing a new rom or kernel...(e.g. Tiamat Moray Rom and/or Odachi Kernel). Look in the Xoom Heaven thread or in the Development section of this form for all of these files.
6.1 This step is identical to 5, but swap out the ROOT zip for the ROM or KERNEL zip. For simplicity, you may want to prepare the micro SD card with both zip files at the same time in step 5.1..."
------------------------
This is still one of the best explanations of how to use adb and fastboot to unlock and root the Xoom and install a custom recovery, etc, and doesn't deserve to buries on back pages of this forum. Hopefully, the step-by-step nature of this guide will help those of you that have limited experience with this kind of tinkering.
Oh, and please feel free to correct any errors or omissions. As I said, it came from several sources and needed to somewhat updated.
Thank you, just bought my xoom yesterday and was confused on the steps to take!
This has made it as clear as possible for me and will follow your instructions to the letter tonight.
Sent from my MZ604 using xda premium
fastyan said:
Thank you, just bought my xoom yesterday and was confused on the steps to take!
This has made it as clear as possible for me and will follow your instructions to the letter tonight.
Sent from my MZ604 using xda premium
Click to expand...
Click to collapse
Good luck! Let us know how you make out and if anything needs to be clarified.
think im doing something wrong as unlocked fine but when i go to install the recovery file it keeps coming up cannot load? any ideas where im going wrong?
been at it 3 hours now lol and losing the will to live im sure its gona be something simples
fastyan said:
think im doing something wrong as unlocked fine but when i go to install the recovery file it keeps coming up cannot load? any ideas where im going wrong?
been at it 3 hours now lol and losing the will to live im sure its gona be something simples
Click to expand...
Click to collapse
Check to make sure that your file download is good, and that you are typing it's name correctly. Better yet, you could rename the file "recovery.img" and that will make it very easy to get it right.
On the sd card?I thought we had to put it into sdk platform tools? I have put it and renamed it onto my sd card but what is the command to flash recovery from sd card?
Also noticed once I have done "adb reboot bootloader" my computer doesn't see the XOOM properly, is in can't see it in my computer but does make a noise when I connect and disconnect is this correct? Debugging is on.
Sent from my MZ604 using xda premium
fastyan said:
On the sd card?I thought we had to put it into sdk platform tools? I have put it and renamed it onto my sd card but what is the command to flash recovery from sd card?
Also noticed once I have done "adb reboot bootloader" my computer doesn't see the XOOM properly, is in can't see it in my computer but does make a noise when I connect and disconnect is this correct? Debugging is on.
Sent from my MZ604 using xda premium
Click to expand...
Click to collapse
When you're in the bootloader, you won't be able to access the SD Card or anything of that sort and adb won't work, in stead, when you're in the bootloader, you're switching over to fastboot. I'm sure if you type in fastboot devices you'll see your xoom listed.
Thank you for the reply and that's one thing sorted but any idea why its telling me "cannot load recovery"? I have tried renaming it and downloaded the recovery file 4 times incase that was wrong but still no joy :-(
I have done this all before on my phone and never had a problem so I must be missing something but f$*@ed if I know what?
Thanks again for your help though.
Sent from my Desire HD using xda premium
Just had a thought. Could it be that the XOOM hasn't actually unlocked, would that cause it to not load? Is there any way to check if its unlocked successfully? Although I did try it twice before?
Sent from my MZ604 using xda premium
Once you got it in the bootloader, you gotta make sure you do fastboot oem unlock, press volume down then up, press volume down again then up again, and let it format and reboot.
If it's already unlocked, you'd get a message telling you so (generally).
Then when you go to flash the recovery, make sure that the recovery image is in the folder where fastboot is and type in fastboot flash recovery recovery.img (if I remember the syntax that is, I'm at work and don't feel like scrolling up or going into the root guide to confirm xD ).
fastyan said:
On the sd card?I thought we had to put it into sdk platform tools? I have put it and renamed it onto my sd card but what is the command to flash recovery from sd card?
Also noticed once I have done "adb reboot bootloader" my computer doesn't see the XOOM properly, is in can't see it in my computer but does make a noise when I connect and disconnect is this correct? Debugging is on.
Sent from my MZ604 using xda premium[/QUOTE
No, sorry, I was trying to respond. when I was tired and distracted.I totally miswrote. Of course the cwm recovery img goes in the platform tools...thank goodness you guys are out there to catch mistakes!
So, I don't know if you had any progress, but not successfully unlocking would surely stop you in your tracks.
Click to expand...
Click to collapse
okantomi said:
No, sorry, I was trying to respond. when I was tired and distracted.I totally miswrote.Oof course the cwm recovery img.. goes in the platform tools...thank goodness you guys are out there to catch mistakes!
So, I don't know if you had any progress, but not successfully unlocking would surely stop you in your tracks.
Click to expand...
Click to collapse
With the way I have my system setup, I can run adb and fastboot wherever I am
No, sorry, I was trying to respond. when I was tired and distracted.I totally miswrote. Of course the cwm recovery img goes in the platform tools...thank goodness you guys are out there to catch mistakes!
So, I don't know if you had any progress, but not successfully unlocking would surely stop you in your tracks.
No progress yet as im at work but when I get home I will start the process from scratch again and see how I get on and will keep you posted.
scsa20 said:
With the way I have my system setup, I can run adb and fastboot wherever I am
Click to expand...
Click to collapse
Care to share???
That would be helpful to many, I'm sure. We could add it to the guide, along with anything else you can think of.
fastyan said:
No, sorry, I was trying to respond. when I was tired and distracted.I totally miswrote. Of course the cwm recovery img goes in the platform tools...thank goodness you guys are out there to catch mistakes!
So, I don't know if you had any progress, but not successfully unlocking would surely stop you in your tracks.
No progress yet as im at work but when I get home I will start the process from scratch again and see how I get on and will keep you posted.
Click to expand...
Click to collapse
If, as you follow this guide, you find any explanations that are not clear or if you think of a step to take or something else that might improve the guide, please post it and we can add it in. It's been almost 6 months since I've unlocked and at least a couple of months since I've had to use adb, so I'm sure I've forgotten some things. Those of you whose experience is fresh can give really good advice. That's how this guide was originally written, by pingvinen, right after he had gone through a grueling rooting process.
okantomi said:
Care to share???
That would be helpful to many, I'm sure. We could add it to the guide, along with anything else you can think of.
Click to expand...
Click to collapse
For windows, if you go into System Properties and choose Advanced, then Environment Variables..., you'll be able to edit the Path variable under System variables, just add the path to where adb and fastboot is located (separated with a semi-colon (;)).
Here's what my Path variable looks like:
C:\Program Files\Common Files\Microsoft Shared\Windows Live;C:\Program Files (x86)\Common Files\Microsoft Shared\Windows Live;C:\Program Files (x86)\NVIDIA Corporation\PhysX\Common;%SystemRoot%\system32;%SystemRoot%;%SystemRoot%\System32\Wbem;%SYSTEMROOT%\System32\WindowsPowerShell\v1.0\;C:\Program Files (x86)\Windows Live\Shared;c:\Program Files (x86)\Microsoft SQL Server\100\Tools\Binn\;c:\Program Files\Microsoft SQL Server\100\Tools\Binn\;c:\Program Files\Microsoft SQL Server\100\DTS\Binn\;C:\android-sdk-windows\tools;C:\android-sdk-windows\platform-tools;C:\Program Files (x86)\Common Files\Acronis\SnapAPI\
Click to expand...
Click to collapse
It's long but hey, see where the android stuff is near the end?
@Okantomi:
We all have learned some things from trial & error (eg.the sk cannot detect java dev kit)
i could only flash recovery after renaming it to recovery(do not forget to add.img in cmd while flashing).also the official motorola name recovery as same.
after downloading sdk and updating to platform tools i have kept a zip in safe location so that i do not need to download again platform tools if i install sdk fresh
initially knowledge was scattered now it is at one place.
right now testing steady hawkin's kernel and new recovery
btw good signature pic.
Ok so another night has gone and still can't get recovery on!! Tried re unlocking the XOOM and every time it comes up with "cannot load recovery.img" I tried installing everything on my laptop and went right from the start and getting exactly the same thing!
Starting to think im never gonna get this sorted now :-( just feels like the XOOM isn't unlocking? Every time I go through the unlocking process it never states that its already unlocked? Is there any way I can check that it is unlocked?
Please help im losing the will to live now lol
Sent from my MZ604 using xda premium
I would say to send it to me and I can take a wack at it but I don't think you want to wait that long to simply root it.
Let me ask you, are you getting any sort of error messages when you do fastboot flash recovery recovery.img? If so, what's that error message?
scsa20 said:
I would say to send it to me and I can take a wack at it but I don't think you want to wait that long to simply root it.
Let me ask you, are you getting any sort of error messages when you do fastboot flash recovery recovery.img? If so, what's that error message?
Click to expand...
Click to collapse
Not getting any error message it just says "cannot load recovery.img"
I have tried with and without the .img and always the same?
Tried going through the whole process again on my laptop incase I had missed something but exactly the same.
When I unlock it I follow the onscreen instructions and at the end it says its complete before it reboots. Then I turn on usb debugging again and reboot bootloader all ok but won't let me load the new recovery?
Normally I would just say it wasn't meant to be and leave as it is but I wont be beaten on this so I'm purposely not installing anything on it till its done. Any ideas apart from bringing it round yours lol ;-)
Sent from my Desire HD using xda premium
I have figured out a way to permanently install ClockworkMod Recovey on your hybrid WebOS/CyanogenMod Touchpad. Like many of you, my ClockworkMod installation failed when I tried to install using ACMEInstaller while I also installed CyanogenMod.
I realize there is now a workaround to "inject" ClockworkMod into your TP using novacom however this requires you to utilize a computer everytime you want to boot ClockworkMod. Follow the instructions below to install ClockworkMod onto your TP permanently and free yourself from your PC!
1. Boot into WebOS
2. Mount TP to your computer and create a "cminstall" folder if it no longer exists after your CyanogenMod installation
3. Copy the "update-cwm_tenderloin-1012.zip" file into the "cminstall" directory, then unmount TP from computer
4. Download the "Internalz Pro" program using the "Preware" application in WebOS if you haven't already (Google is your friend if you get stuck here)
5. Open "Internalz Pro" and navigate to the "boot" menu (will most likely require you to tap the top-most icon of a folder with two dots next to it to get to the root of the TP - should be second folder down)
6. Tap on the file "uImage.ClockworkMod" and select "move"
7. Navigate to the "media/internal/" directory and click "select" to move file
8. Now tap on the file "update-uimage" and move the file to the same "internal" directory you did in step #7
9. Exit from "Internalz Pro" and reboot device while holding down the up volume key, which will take you in to WebOS Recovery (or select WebOS Recovery when you get to the moboot screen you may have previously installed) - you should now see a large USB icon and should be connected to your computer using a usb cable
10. Go to your command prompt in Windows and navigate to the menu where you have novacom installed - you should also have the ACMEInstaller binary file copied into this directory by now (If you don't know what I'm talking about, remember Google is your friend)
11. Type in "novacom boot mem:// < ACMEInstaller" in the command line and press enter
12. You should now see ClockworkMod recovery installing on your TP - Once it reboots into moboot select "boot ClockworkMod" and watch it boot into ClockworkMod!
13. After celebrating, boot back into WebOS, go into "Internalz Pro" and move the file "update-uimage" back into the "boot" directory - the "uImage.ClockworkMod" file that you put in the "Internal" directory is no longer needed since you reinstalled ClockworkMod properly
Essentially the boot directory was overloaded which caused for insufficient space when installing ClockworkMod. Now you should be able to boot into WebOS, CyanogenMod, WebOS, AND ClockworkMod Recovery without a computer. As always, I do not take responsibility for you bricking your TP or variability you may have... use this information if it is helpful but don't blame me if something goes wrong. I'm just trying to help out the community that has helped me for so long.
Let me know if this is helpful to you. Thanks!
dseelye
What!?
Hi!
firstly, thank you for making this guide, i know that alot of people like myself will appreciate it.
but i've run into a problem, see, now i don't have the option to boot into cyanogenmod anymore !
can i flash it in clockworkmod, or do i have to do it all over again?
a reply would be appreciated
you most likely copied the wrong file from the boot folder, as there was one for clockworkmod and one for cyanogen mod... look and see if you incorrectly copied the cyanogenmod "uImage.CyanogenMod" to your internal sd card to free up space. You will have to move this back to the boot folder and grab the other one.
Thank you VERY much!
and thanks for the INCREDIBLY quick reply!
EDIT: IT WORKED!!! YOU'RE THE MAN!!!!!
No problem... let me know if that solved your concern...thx
EDIT: Oh, just saw the edit of your post...great, glad that was it!
Just wondering... how permanent is permanent?
For instance, if I use "web doctor" to restore my touchpad, will the recovery be overwritten?
Yes, I just mean that you don't have to "inject" clockworkmod into your TP using your computer which was the workaround for the people who couldn't get it installed originally during the CyanogenMod installation. This just installs it properly but can be wiped with WebOS Doctor like anything else...
bigblueshock said:
Just wondering... how permanent is permanent?
For instance, if I use "web doctor" to restore my touchpad, will the recovery be overwritten?
Click to expand...
Click to collapse
Yeap... it will not delete a single bit of CM7, just gonna restore the original bootloaders, delete moboot and skip CWM /Android on boot...
Running again ACME with only moboot and CWM in the cminstall folder will restore them.
....After WebOS doctor... it will show CM7 as the last time you shut it down.
Sent from my GT-I9000 using XDA App
I followed directions exactly but I am not seeing the uImage.clockwork in the boot folder. Any suggestions? I see that file in the cminstall folder, do I just leave in there or should I copy directly to media\internal?
Sent from my SPH-D710 using xda premium
The "uImage.ClockworkMod" may not be in the boot directory I suppose if the previous install attempts didn't put it there so not sure why it isn't in yours. Essentially you are just trying to move some of the larger files out of that directory so you can install ClockworkMod properly as the space constraint of the partition size seems to be the issue. The other file I mentioned, "update-uimage", is actually the largest one I found and you may be able to do the ClockworkMod install properly by only removing that one temporarily. Let us know if you are able to resolve.
I've installed clockworkmod recovery with no errors on the first try, is it advisable that I need to use this method?
I was installing cwm for the first time. I didn't include it originally with the install of cyanogen mod, I guess that's why it wasn't in the boot folder. I placed both files in the media\internal directory and also inside the cminstall folder and ran the command and it worked fine. When I checked internalz pro to remove the files, the cminstall folder and uimage files were gone already. So it looks like I am good to go. cwm is working, I flashed gapps from it. Thanks for reply.
Now I just need to figure out how to make phone calls.
Sent from my SPH-D710 using xda premium
If you installed ClockworkMod completely the first time and it works, then you definitely don't need to do this as this thread was intended for those that tried to install it at the same time as when they installed CyanogenMod and ClockworkMod Recovery didn't install properly. These instructions are to outline how to get it installed correctly as just trying again using ACMEInstaller wasn't working for anyone due to the small size left in the boot directory.
hey thanks for the fix but after the fix i cant get into the market
Not sure why you can't access the market...no issues here. I would suggest reinstalling the gapps zip file and possible the market fix file that are out there now that you have clockworkmod working properly.
thanks for the help thats what i had to do
Hi, the "move" option isn't available, only "copy" "info" and "open"
The entire directory is "view-only"
Not sure why "move" isn't available for you... its been a while since I installed Preware and Internalz Pro so I must have gotten root access somehow and that's why it shows up for me and others. I'd suggest searching for how to obtain root access to WebOS to find your answer... possibly development mode if you haven't already done that but I thought that was required to get Preware installed in the first place.
Move command
dseelye said:
Not sure why "move" isn't available for you... its been a while since I installed Preware and Internalz Pro so I must have gotten root access somehow and that's why it shows up for me and others. I'd suggest searching for how to obtain root access to WebOS to find your answer... possibly development mode if you haven't already done that but I thought that was required to get Preware installed in the first place.
Click to expand...
Click to collapse
I have the same problem. Move/delete commands are available on the media/internals but on boot folder move is not available.
Thanks
Awesome man! Been struggling with this since two days. Thanks a lot for the fix and step by step instructions
---------- Post added at 09:07 AM ---------- Previous post was at 09:00 AM ----------
tmkhan said:
I have the same problem. Move/delete commands are available on the media/internals but on boot folder move is not available.
Click to expand...
Click to collapse
After Opening "Internalz Pro", Open "Preferences", scroll down to the bottom. You will see an option called "Master mode". Turn it on. You will get read/write access to the boot folder.
alright guys so the procedure is kinda complicated compared to Windows but not really lol Welp here it goes
TUTORIAL
1st: Download all the files needed to install (ACMEInstaller, CM7, Clockworkmod recovery, and Moboot) from rootzwiki
2nd: Once downloaded place all of those zips EXCEPT for ACMEInstaller into a folder on your touchpad called "cminstall"
3rd: Have the novacom drivers installed (google universal novacom installer, should be a .jar file)
4th: once that is done find the novacom drivers by searching in the finder (search novacom )
5th: unzip ACMEInstaller.zip and place the one that isn't the readme in with novacom
6th: drag novacom over to a terminal window followed by "boot mem:// <" then without a space drag the ACMEInstaller file over to the end of that string. (The result should look something like this Garrett-Witts-MacBook-Pro-2:~ garrett_witt$ /opt/nova/bin/novacom boot mem:// </opt/nova/bin/ACMEInstaller)
7th: Behold! You have installed cm7 using mac!
thank you very much!
You are very welcome man, just giving back to the community, was it easy to follow? It was my first guide lol
I would've put:
1st: Download all the .ZIP files needed to install (ACMEInstaller, CM7, Clockworkmod recovery, and Moboot) from rootzwiki via the forum link HERE
2nd: Once downloaded place all of those zips EXCEPT for ACMEInstaller into a folder on your touchpad (via USB mount) called "cminstall". Optionally you can also download the latest CM7 Google Apps package from http://goo-inside.me/gapps/ and put that in there as well - this is required if you want access to the Android market.
3rd: Download Novacom from HERE & install it.
4th: Unzip ACME Installer onto your desktop
5th: Power off your TouchPad, then turn it on again, holding down the Volume-Up button until a large USB logo appears on the screen.
5th: Open a terminal window (click on spotlight, type terminal and select it) and type the following into the terminal window:
novacom boot mem:// <~/Desktop/ACMEInstaller
The installer will now proceed. It'll adjust partition sizes, install ClockWorkMod, CM7 itself, the Moboot bootmenu and optionally the Google Apps package. WebOS will remain the default OS.
I got the install on my touchpad running. It got quite far and then stopped with the following lines ending it.
"Looking for the install images...
Initial install files not found.
Please download it from touchpad.linuxhacker.ru
and put in sminstall folder on media partition
the name should start with update-cm and end with .zip"
Any ideas?
liemydude said:
I got the install on my touchpad running. It got quite far and then stopped with the following lines ending it.
"Looking for the install images...
Initial install files not found.
Please download it from touchpad.linuxhacker.ru
and put in sminstall folder on media partition
the name should start with update-cm and end with .zip"
Any ideas?
Click to expand...
Click to collapse
Did you create the folder titled "cminstall" on the touchpad through webos?
and place in that folder the files "update-cyanogenmod...", "update-clockworkmod...", "update-gapps..." ?
thanks for the feedback knight, I will rewrite when I get the chance.
I can not get the Novatel package to install on 10.7.2 (Lion). It errors on the final step. Anyone else get it to install?
Boutwell, I think you may have the same problem I had. If you downloaded the SDK for the Novacom drivers from the link in the original README file you may have the version known to be in compatible with OS X Lion. Don't have the links to hand, but you can get the latest version of the SDK installer from the HP/WebOS site.
EDIT - found the link here: https://developer.palm.com/content/resources/develop/sdk_pdk_download.html#c23352
Download the Mac version of the SDK and install, no need to bother with the VMWare section and during the installer's option selection, clear the tick boxes for the Emulator and PDK as they are not needed.
Is this confirmed working / updated? I don't want to get out of bed to fire up my PC. Haha.
yes this works. i've done it on my macbook and my sister was able to do this on her macbook
Does Wifi work?
6th: drag novacom over to a terminal window followed by "boot mem:// <" then without a space drag the ACMEInstaller file over to the end of that string. (The result should look something like this Garrett-Witts-MacBook-Pro-2:~ garrett_witt$ /opt/nova/bin/novacom boot mem:// </opt/nova/bin/ACMEInstaller)
Click to expand...
Click to collapse
I get here and nothing. I followed the instructions perfectly. Touchpad is on the USB screen and Terminal is sitting there...
---------- Post added at 08:23 PM ---------- Previous post was at 07:46 PM ----------
chrischoi said:
I get here and nothing. I followed the instructions perfectly. Touchpad is on the USB screen and Terminal is sitting there...
Click to expand...
Click to collapse
I ended up having to redo the novacom drivers. Downloading them from the SDK pack is the way to go.
These ^last instructions worked best for me. Something about where my novacom and acme files were located had me messed up.
chrischoi said:
I get here and nothing. I followed the instructions perfectly. Touchpad is on the USB screen and Terminal is sitting there...
---------- Post added at 08:23 PM ---------- Previous post was at 07:46 PM ----------
I ended up having to redo the novacom drivers. Downloading them from the SDK pack is the way to go.
Click to expand...
Click to collapse
Just the Novacom drivers were giving me a install error. I also found that it's more consistent with changing director, then running the commands.
hey thanks for the write up very helpful
ps digging the A.B.R
Yo Garrett I gotta say thank you man. I been struggling with that terminal command for 2 hours. My damn eyes hurt. Every site was just giving windows info. Thank you much man. I owe you a drink
Thanks for this tutorial, mate. For those(lazy bastards) who don't like reading instructions, here's a video guide :
How to Install Android on the HP TouchPad (Mac Version)
if anyone else is having issues with mac try running the commands in su mode.
Thanks... very easy to follow compared to the original. The original had nothing about putting the files onto the device. Go figure...
This guide was written to provide more specific information for installation instructions than the OP below.
The Tubuntu installer application will not install the updated kernels for SBK1 devices and the manual procedure in post #2 will tell you what you need to do.
OP for Tubutnu by x3maniac
1. Download the newest “tubuntu v0.x.x” without Prime (system.img) or Ubuntu.img as it is written in the OP.
a. This download contains the application, boot.img file, and basic kernels available at the time of this guide needed for installation. There will be updates for kernels specific to an Ubuntu image as the developer is able to work on them. Check for new downloads and posts.
b. The download also contains drivers and installation for APX mode located using the “Other” tab in the application.
c. This download does NOT contain the Linux operating system nor the Android ROM.2. Extract all the files in “tubuntu v0.x.x” to a Tubuntu folder wherever you wish. 7-Zip is the zip program of choice but any others should work fine.
3. Download Prime ROM [stock hc w/ root](system.img)
a. This download is the system.img that contains a root enabled Android ROM.4. Extract the system.img file from this download.
a. Copy this file to the \images directory. The images directory is a sub folder of the TF-101 Ubuntu Installer application that you extracted in step 2.5. Download the Ubuntu image of your choice.
a. Currently there are 2 Lubuntu downloads. Read the bullets and determine which one you want.6. Extract the image file of this download and place it in the \images directory. Rename this file to ubuntu.img.
7. Open the TF-101 Ubuntu Installer application.
8. Connect your usb cable to the TF-101 and the computer.
a. Shut down the tablet.9. Enter APX mode by holding the volume up button first, then hold the power button until you hear the usb sound from the computer.
a. Your screen will be black and the TF-101 Ubuntu Installer application will light up green and say APX Detected if you correctly entered APX mode.10. Change the dropdown to SBK 1 located directly below the green APX Detected text.
11. Click on the Flash tab.
a. Select Android/Ubuntu and then hit Flash.
b. Android is the primary boot option here.12. You will see an install log in the right of the application. Mine takes about 15 minutes or so but you will know you are finished when you see the Android ROM load as well as the red text APX NOT Detected (in case your screen is off when you come back).
13. Proceed with setting up Android. DO NOT reboot or power off before the initial Android set up is complete.
14. Once completed and you wish to enter Lubuntu, power off the TF-101 and hold down volume down first and then power. You will see your screen say hit volume up in 5 seconds for recovery. Hit volume up within 5 seconds and it should boot your Linux graphical desktop environment.
Instructions for installing new kernels for SBK1.
1. In your Tubuntu installation directories, locate transformer.bct and bootloader.bin.
a. Copy these 2 files to the \bins directory of the Tubuntu installation application.2. Download the updated kernel from the OP.
a. Extract the .img file into the \bins directory of the installation application. You do not need to rename it because the command you enter in step 3 part b indicates the name of the kernel file.3. Open a command prompt to the directory of \bins for the Tubuntu installer application.
a. Type this command and hit enter: wheelie -1 -o 0x300d8011 --bl bootloader.bin -c transformer.bct
b. Type this command and hit enter: nvflash -r --download 6 whatever_the_kernel_filename_is.img
c. The filename is the name of the kernel you extracted and copied into the \bins directory. This name can really be anything so long as the command you enter reflects that filename.4. After the copy completes you will be back at the command prompt.
a. Type this command and hit enter: nvflash -r --go5. Your tablet will reboot after the nvflash mode is exited and depending on your configuration it will boot to Android. Boot to Linux now.
6. Download the supplemental kernel file to the root of your filesystem That is the / directory.
a. Open terminal and type this and press enter: sudo wget http://novaspirit.com/tubuntu/kernel_sup.tar.gz /
b. Then type this command and press enter: sudo tar zxvf /kernel_sup.tar.gz
c. This supplemental is installing modules and drivers to the appropriate locations.
d. Reboot.7. Please understand names of files especially the kernels and updates will change periodically. The commands and methods of extracting have not changed at this point so substitute the appropriate filename and you should be good to go.
For SBK1 devices, the installation of a custom Android ROM using recovery is very similar to updating the kernel instructions in the post above.
Instructions for installing custom ROM's for SBK1 with Lubuntu installed.
1. In your Tubuntu installation directories, locate transformer.bct and bootloader.bin.
a. Copy these 2 files to the \bins directory of the Tubuntu installation application.3. Copy the file cwrrecovery.img to the \bins folder.
a. You should be able to substitute a newer recovery file than what comes with the Tubuntu installation application.2. Download the zip file of the custom Android ROM you wish to install.
a. Copy it to either your Internal SD card or External SD card. Depending on the recovery version you flash you may not be able to use your Internal SD card.3. Open a command prompt to the directory of \bins for the Tubuntu installer application.
a. Type this command and hit enter: wheelie -1 -o 0x300d8011 --bl bootloader.bin -c transformer.bct
b. Type this command and hit enter: nvflash -r --download 5 cwrrecovery(orwhateverfilenameyourrecoveryis).img
c. The filename cwrrecovery.img is the name of the recovery that comes with the installer application. Please substitute appropriately if you are going to flash a different recovery application. You can also use TWRP just use the appropriate .img file name.4. After the copy completes you will be back at the command prompt.
a. Type this command and hit enter: nvflash -r --go5. Your tablet will reboot after the nvflash mode is exited and depending on your configuration it will boot to Android.
a. Now you want to boot to the Android recovery. Do that by powering off the tablet and booting like normal into recovery mode. This should be volume down and power. Hit volume up when prompted to do so. Flash your ROM according to the ROM owner's instructions. I recommend to complete your ROM's installation set up before proceeding to step 6.6. You must now flash your Tubuntu Linux kernel back or you will not be able to boot into Linux. Follow the instructions again from the \bins directory using the command prompt and putting your tablet back into APX mode which is volume up and the power button until the Tubutnu installation application shows green for APX Detected.
a. Type this command and hit enter: wheelie -1 -o 0x300d8011 --bl bootloader.bin -c transformer.bct
b. Type this command and hit enter: nvflash -r --download 5 whatever_the_kernel_filename_is.img
c. Type this command and hit enter: nvflash -r --go7. You should now be back into your Android ROM again. From here simply power off and boot into recovery using volume down and power. Then hit volume up when it says to on the screen. If Linux boots without issue then you have successfully reinstalled your kernel.
I did exactly what's in the post. With Tubuntu 0.4.7, Prime ROM, Lubuntu V1.1-rc1 (12.10) and the *updated kernel 12/10/2012* (without supplements)
But after Android initial boot, I reboot but it doesn't finish booting Android. It stops here:
http://i50.tinypic.com/2zswdw3.jpg
Anything I can do to fix this? Android does boot properly, but Lubuntu doesn't
If anyone knows how to fix this with only Ubuntu (and without Android) then that is fine too..
TomTcom said:
This guide was written to provide more specific information for newcomers.
The Tubuntu installer application will not install the updated kernels for SBK1 devices and the manual procedure in post #2 will tell you what you need to do.
Click to expand...
Click to collapse
sainthout said:
I did exactly what's in the post. With Tubuntu 0.4.7, Prime ROM, Lubuntu V1.1-rc1 (12.10) and the *updated kernel 12/10/2012* (without supplements)
But after Android initial boot, I reboot but it doesn't finish booting Android. It stops here:
http://i50.tinypic.com/2zswdw3.jpg
Anything I can do to fix this? Android does boot properly, but Lubuntu doesn't
If anyone knows how to fix this with only Ubuntu (and without Android) then that is fine too..
Click to expand...
Click to collapse
0.4.7 fixes the issue with sbk1 and you don't have to do it with these instructions anymore.
However I did try the newer kernel and got stuck at the same spot you did using my instructions just before the 0.4.7 was uploaded. Go to the original thread and post the issue there.
Thanks for the quick reply! Will post the issues
Outdated Thread But Valid Information
This thread is now outdated. X3Maniac has updated his Tubuntu installation application (0.4.7) to fix the issues with installing kernels and recoveries for SBK1 devices.
The information in this thread is still valid for behind the scenes and you can still use the wheelie and nvflash as standalone items if you wish to do something with your device outside the scope of the main thread.
Thanks for all the thanks from users!
Found a bug with 0.4.7. It's possible the tab may not reboot into Prime automatically with this version. When the dev has time it will get updated. If it doesn't reboot and the Tubuntu application says everything is done, manually hold power and let it reboot to Prime to finish installation.
question..
TomTcom said:
This guide was written to provide more specific information for newcomers.
The Tubuntu installer application will not install the updated kernels for SBK1 devices and the manual procedure in post #2 will tell you what you need to do.
1. Download the newest “tubuntu v0.x.x” without Prime (system.img) or Ubuntu.img as it is written in the OP.
a. This download contains the application, boot.img file, and basic kernels available at the time of this guide needed for installation. There will be updates for kernels specific to an Ubuntu image as the developer is able to work on them. Check for new downloads and posts.
b. The download also contains drivers and installation for APX mode located using the “Other” tab in the application.
c. This download does NOT contain the Linux operating system nor the Android ROM.2. Extract all the files in “tubuntu v0.x.x” to a Tubuntu folder wherever you wish. 7-Zip is the zip program of choice but any others should work fine.
3. Download Prime ROM [stock hc w/ root](system.img)
a. This download is the system.img that contains a root enabled Android ROM.4. Extract the system.img file from this download.
a. Copy this file to the \images directory. The images directory is a sub folder of the TF-101 Ubuntu Installer application that you extracted in step 2.5. Download the Ubuntu image of your choice.
a. Currently there are 2 Lubuntu downloads. Read the bullets and determine which one you want.6. Extract the image file of this download and place it in the \images directory. Rename this file to ubuntu.img.
7. Open the TF-101 Ubuntu Installer application.
8. Connect your usb cable to the TF-101 and the computer.
a. Shut down the tablet.9. Enter APX mode by holding the volume up button first, then hold the power button until you hear the usb sound from the computer.
a. Your screen will be black and the TF-101 Ubuntu Installer application will light up green and say APX Detected if you correctly entered APX mode.10. Change the dropdown to SBK 1 located directly below the green APX Detected text.
11. Click on the Flash tab.
a. Select Android/Ubuntu and then hit Flash.
b. Android is the primary boot option here.12. You will see an install log in the right of the application. Mine takes about 15 minutes or so but you will know you are finished when you see the Android ROM load as well as the red text APX NOT Detected (in case your screen is off when you come back).
13. Proceed with setting up Android. DO NOT reboot or power off before the initial Android set up is complete.
14. Once completed and you wish to enter Lubuntu, power off the TF-101 and hold down volume down first and then power. You will see your screen say hit volume up in 5 seconds for recovery. Hit volume up within 5 seconds and it should boot your Linux graphical desktop environment.
Click to expand...
Click to collapse
i just succeeded dual booting into ubunto.the prime rom just booted...can i install eos jb rom and still dual boot to ubuntu? thanks in advanced
Yes you can. You will need an updated recovery .img file that supports jb. You temporarily flash the new recovery boot into it then install the new rom. See my post on installing updated android roms. Its the third one I think.
oh sorry for the silly question,,i got it now thanks a lot.. nice job
Hi there,
First off, thanks for the tutorial and hard work!
I've been able to successfully install Lubuntu v1.2 and Lubuntu V1.1-rc1 but I've run into issues with both that I'm hoping you can help me with.
When I installed v1.2, my wireless adapter didn't work and I wasn't able to copy any files (kept saying I was out of space, probably a mounting issue).
When I installed v1.1-rc1, things seemed to work well (wireless worked) but when I tried to upgrade the kernel to 3.1 following the instructions, my mouse pad stopped working and so did my wireless adapter again. I saw that there is a way to fix the mouse pad but it seemed to require an internet connection. Any idea what I did wrong or how to fix the wireless on either v1.2 or on v1.1-rc1 with the 3.1 kernel?
Thanks!
You're welcome.
To solve the space issue, open terminal and execute this command: sudo resize2fs /dev/mmcblk0p8
The wireless adapter isn't working because the 3.1 kernel is not stable. Do Not Use It.
Get this from the OP:
Kernels
#470 Controlling your CPU for stability
Stable kernels (use with care for OC version)
[extreme]
2.6.36 - [cpu 1.6 ghz] [gpu 400mhz] - download
benchmarks - blowfish score 30
glxgear - 70 fps
Then get the supplement from the OP:
kernel supplement - 2.6.36.4-1210.zip
extract and copy the kernel suppliment to /lib/modules/
TomTcom said:
You're welcome.
To solve the space issue, open terminal and execute this command: sudo resize2fs /dev/mmcblk0p8
The wireless adapter isn't working because the 3.1 kernel is not stable. Do Not Use It.
Get this from the OP:
Kernels
#470 Controlling your CPU for stability
Stable kernels (use with care for OC version)
[extreme]
2.6.36 - [cpu 1.6 ghz] [gpu 400mhz] - download
benchmarks - blowfish score 30
glxgear - 70 fps
Then get the supplement from the OP:
kernel supplement - 2.6.36.4-1210.zip
extract and copy the kernel suppliment to /lib/modules/
Click to expand...
Click to collapse
Awesome, works like a charm. Thanks again!
Not sure if I'm the only one experiencing this, but every now and again whenever i click anywhere it thinks I'm trying to move a file (shows the little file icon when I move the mouse). Is this a known bug or just something in my settings I need to change?
Thanks!
---------- Post added at 12:40 PM ---------- Previous post was at 12:19 PM ----------
I also just found that my sound stopped working. It was working before when I used the instructions from the original post (using alsamixer) but I guess somewhere along the way of me messing around I broke it. Here is the error output when I try to play an mp3 in mplayer:
Code:
==========================================================================
Requested audio codec family [mpg123] (afm=mpg123) not available.
Enable it at compilation.
Opening audio decoder: [ffmpeg] FFmpeg/libavcodec audio decoders
AUDIO: 44100 Hz, 2 ch, floatle, 128.0 kbit/4.54% (ratio: 16000->352800)
Selected audio codec: [ffmp3float] afm: ffmpeg (FFmpeg MPEG layer-3 audio)
==========================================================================
Assertion 'pthread_mutex_unlock(&m->mutex) == 0' failed at pulsecore/mutex-posix.c:108, function pa_mutex_unlock(). Aborting.
MPlayer interrupted by signal 6 in module: ao2_init
I've tried searching for a solution but still no luck. I've also tried other players and they don't work either. Any help would be greatly appreciated.
Thanks!
Treizy said:
Not sure if I'm the only one experiencing this, but every now and again whenever i click anywhere it thinks I'm trying to move a file (shows the little file icon when I move the mouse). Is this a known bug or just something in my settings I need to change?
Thanks!
---------- Post added at 12:40 PM ---------- Previous post was at 12:19 PM ----------
I also just found that my sound stopped working. It was working before when I used the instructions from the original post (using alsamixer) but I guess somewhere along the way of me messing around I broke it. Here is the error output when I try to play an mp3 in mplayer:
Code:
==========================================================================
Requested audio codec family [mpg123] (afm=mpg123) not available.
Enable it at compilation.
Opening audio decoder: [ffmpeg] FFmpeg/libavcodec audio decoders
AUDIO: 44100 Hz, 2 ch, floatle, 128.0 kbit/4.54% (ratio: 16000->352800)
Selected audio codec: [ffmp3float] afm: ffmpeg (FFmpeg MPEG layer-3 audio)
==========================================================================
Assertion 'pthread_mutex_unlock(&m->mutex) == 0' failed at pulsecore/mutex-posix.c:108, function pa_mutex_unlock(). Aborting.
MPlayer interrupted by signal 6 in module: ao2_init
I've tried searching for a solution but still no luck. I've also tried other players and they don't work either. Any help would be greatly appreciated.
Thanks!
Click to expand...
Click to collapse
See KingZaks post for sound settings. It's in the op and his signature.
The clicking shouldn't do that every time. Did you extract the supplemental zip and are you using the 1.2-1.6ghz kernels?
Hmm, I'm thinking of installing fresh to see if things get fixed. Is there a way to do that without touching the Android partition? I don't want to have to reflash EOS and what not. Do I just not include the Prime img in the images folder?
Thanks!
A Terribly Confused Noob!
Hello:
I am terribly confused and I hope that someone can help me to understand a few things! I am sorry if I don't understand all the links but they seem to go round and round. Right no I have no less that 25 tabs open trying to figure out the first step.
So, to my first question (probably the first of many): This guide was written to help "newcomers", of which I am definitely one. But, right under that statement comes the statement "The Tubuntu installer application will not install the updated kernels for SBK1 devices and the manual procedure in post #2 will tell you what you need to do." Does that mean I'm actually supposed to start at Post #2? But Post #2 assumes I already have "Tubuntu installation directories", which I don't have so I can't locate the two files.
I am attempting to be a user of Ubuntu on my Transformer, not a developer - I take my hat off to all of you that have put your Transformers in harm's way developing the techniques and software that I want to use, but the instructions are terribly confusing for someone not familiar with all of the terms!
Any help would be most appreciated and I thank you in advance.
Sparky
TheArtfulDodger said:
Hello:
I am terribly confused and I hope that someone can help me to understand a few things! I am sorry if I don't understand all the links but they seem to go round and round. Right no I have no less that 25 tabs open trying to figure out the first step.
So, to my first question (probably the first of many): This guide was written to help "newcomers", of which I am definitely one. But, right under that statement comes the statement "The Tubuntu installer application will not install the updated kernels for SBK1 devices and the manual procedure in post #2 will tell you what you need to do." Does that mean I'm actually supposed to start at Post #2? But Post #2 assumes I already have "Tubuntu installation directories", which I don't have so I can't locate the two files.
I am attempting to be a user of Ubuntu on my Transformer, not a developer - I take my hat off to all of you that have put your Transformers in harm's way developing the techniques and software that I want to use, but the instructions are terribly confusing for someone not familiar with all of the terms!
Any help would be most appreciated and I thank you in advance.
Sparky
Click to expand...
Click to collapse
Hey Sparky, there's no more active development on this just so you are aware. That means you can make your own images for newer Linux builds if you wish but things such as hardware acceleration and kernels will not be updated.
In step 1 of my guide you are going to the OP link by the dev who made the Windows based Tubuntu application.
Go to where you see these links:
tubuntu v0.4.7 [1mb] Executable ONLY - download v0.4.2b and replace the tubuntu.exe with this one
download v0.4.7 (jan, 3 2013)
tubuntu v0.4.6beta [1mb] Executable ONLY - download v0.4.2b and replace the tubuntu.exe with this one
download v0.4.6b (dec, 10 2012)
tubuntu v0.4.2beta [78mb] without Prime(system.img) or ubuntu.img
download v0.4.2b (dec, 7 2012)
tubuntu v0.3alpha [57mb] without Prime(system.img) or ubuntu.img
download v0.3a
Prime ROM[stock hc w/ root](system.img)
download
Download tubuntu v0.4.2beta (78mb).
Download tubuntu v0.4.7 (1mb).
Extract the files to whatever location on your Windows machine.
The 1mb file is a replacement of tubuntu.exe file. So just copy/paste and overwrite that file on your Windows machine.
Do you know how to put your tablet in APX mode? If not, you open tubuntu.exe (you might need .net 4.0 Microsoft framework to run the tubuntu.exe). With the tablet off and usb connected to your windows machine, hold volume up and power. The application tubuntu.exe should have a green indicator that it's connected. Change the dropdown to sbk1.
From there you can choose how you want to flash, such as android as the default boot and linux as the secondary boot.
Ignore.