Related
My screen has gone completely white.... I bought the phone online from an "authorized dealer" who won't reply to me now. I live in the US and O2 does not appear to have any US contact info... Am i screwed on this expensive phone i bought 6 months ago?
Anyone had experience with this?
S
stuart.myers said:
My screen has gone completely white.... I bought the phone online from an "authorized dealer" who won't reply to me now. I live in the US and O2 does not appear to have any US contact info... Am i screwed on this expensive phone i bought 6 months ago?
Anyone had experience with this?
S
Click to expand...
Click to collapse
I guess you already tried hard reset?.
Can you get to bootloader mode?.
Tried hard resets, and getting to bootloader mode, i think this is a malfunction with the actual device, I just need to find out how to get in touch with o2 support internationally, i was wondering if someone on here may have had this problem too.
Thanks.
white screen - connector loose?
I too have this problem - but if I twist the screen away from the keyboard I get the display back. I suspect there's a connector loose inside but haven't looked inside.
Anyone on the forum any experience of getting inside and reseating connectors?
xda operation
tophamn said:
I too have this problem - but if I twist the screen away from the keyboard I get the display back. I suspect there's a connector loose inside but haven't looked inside.
Anyone on the forum any experience of getting inside and reseating connectors?
Click to expand...
Click to collapse
Hello there,
I had to get inside my xda to replace the screen that one of my dear rug rats broke. it is quite easy to do, and you only need to get into the screen side of it to get at the conectors. spin the screen half way round and look at the bottom and you will see 6 small screws. take out the two furthest out and two in the middle nearest the screen side. if you take them all out the whole thing becomes hard to handle. the front cover should GENTLY leaver off, and the cables to it exposed. even if they look in place lift the catch holding them in place and take them out and wipe the contacts with a cloth. just be very carefull with the cable strips as they tear very easy. . any problems then PM me
TTFN
Jay
White Screen
Try www.gpsmidlands.co.uk they replaced my ribbon assembly the same day.
Xda Lcd Repair
Try http://www.pda-repairs.co.uk
Brilliant
thanks for this posting - worked perfectly once i had worked out that atually you need to remove the screws further away from the screen in the middle. but otherwise I have successfully resurected a brick into a working universal! thanks!
Sark
Hello everyone...
Ive been doing as much research as I can, but can't find any solution.
I had to purchase a new LCD screen for my cingular 8125.
When i installed the screen, it only boots up with a white screen. Ive read that this has happened to a few others, but no one has posted a solution.
All cables are connected securely, and pushed in far enough. i've experiment with everything. Ive hard reset, ive even tried with another motherboard from a different 8125 phone. nothing but a white screen. I plug my old screen in (still works, just discolored), and it works fine.
Ive read somewhere that there are two generations of the screens. But the part numbers on the screens match up, so im not sure that this is the problem.
Any suggestions? Could the screen just be no good?
Any help is appreciated.
Thanks!
I had a problem with a white stripe when I replaced my screen. I returned it and got a new one...problem solved.
i'm assuming im going to have to return it as well, but i'm trying to avoid the inconvience if possible. ive read that a few people have had this problem, and later replied to their own post saying they fixed it...but never said how...
I had this last week - it was a case of not quite seating the screen ribbon connector properly.
Severl times I fired it p only to see a fully white screen, playing around with the seating of the connector fixed it.
nope...ive messed around with it numerous times. just pulled it back out and tried again...actually hooked up what i needed without putting the phone back together so i could mess around with the ribbon while the phone was powered on...still just white....i suppose it has to be a bad screen?
could be a bad screen.
did you replace the tape that was on the LCD ribbon?
I have replaced about 25 screens and that tape is very important..trust me.
Ok so I have the fabled white screen issue on an 8525. When it first occurred I searched and read all the write ups, decided I had the ribbon cable issue. Took it apart and simply unplugged and replugged the ribbon cable with great results, no more white screen.
I repeated once when it came back after being bumped around, again with positive results...but this last(3rd)time instead of it working I now get white screen 95% of the time. I re-notched the sliders the first time, and last time.
During the 5% it works I noticed the charge light would correspond to it going white.This never happened before...
Example:
When OFF - Connect charger, Red light for 1 second, then nothing=White screen from power on
When OFF - Connect charger, Red light for 1 second, then orange charge indicator = normal startup
When ON and Working - Connect charger, no light, no charge - reboots to white screen
When ON and Working - Connect charger, orange charge indicator, reboots normally.
There is no heat or noticeable pressure on any parts, everything seems to fit normally.
It does boot normally with screen white.
Any ideas? I really don't want to give up on this thing, is there any hope? or just ebay it for parts?
Thanks
-Nick
same problems here, if someone could just tell me what parts to order, cause I have no warranty (ordered over ebay). I tried both the instruction that has chinese fonts on the page , and other from R&R, no luck, white screen all the way..
I had the WSOD and took it apart and reassembled a few time. The 3rd or 4th time the screem came back, but now it is shifter to the right around 1/4" or so. I mean there is just white along the left edge, then the normal screen/color starts and is cut off on the right.
Does anyone know how to correct that, is it related to the same flex cable or is there something else I disturbed?
mine will fade to white.. then i just push the power to put it in standby, then push power again to wake it back up and back to normal.. it rarely does it but still annoying...
If You Ordered From At&t
I had this problem about 2 weeks ago!!!!
I thought it was a fluke!
Anyway, walked over to 43rd and Lexington (NYC FOR THOSE WHO DON'T KNOW THAT MANHATTAN IS THE CENTER OF THE WORLD)
and they gave me the EXCHANGE HOTLINE for at&t.
I called them up, told them my screen is fading to WHITE and the lady sent me a new or referbished phone.. i dont even know.
Just so you know, i ordered my phone on AMAZON with a new activation. its covered under the MANUFACTURERS warentee for a full year from the date of purchase... so is the REPLACEMENT PHONE... but not from the date of replacement, just the date of purchase.
did anyone get deeper into this yet? I got a 8500 (need those without camera) from ebay USA, already with white screen. After reading here, that this is mostly an issue with connectors, I bought it, disassembled it and reassembled it, though still white. Should I give the contacts a treatment with contact-spray? (there's a tuner spray that doesn't leave residues) Or is there something broken within the ribbon cables? Seller said it has been dropped (but he also said, he didn't want to open it, while it clearly has been opened, one screw missing and warranty seal gone). It ssems to boot up normal otherwise, I hear a sound after the boot process, so probably this isn't a software issue?
Edit: another thing I noticed: When I run it without any keyboard connected at all, it's also white. I then connected the dpad again, and I could see a hint of the at&t logo in the lower part of the screen. When I pressed around on the back of the dpad a bit, all LEDs would go on/off... Sound to me like the dpad has gone bad, possible?
Edit II: Got it. Using a 20x eyeloupe I found that the PCB of the DPad is broken under the little chip on it. Now I just gotta find a dpad here in germany, but I assume those Hermes' are all equal...
hello
where can I get manual (if there is one) for disassembling hermes. link in wiki does not work.
thanks
this worked good for me
http://inuchanbt.blog54.fc2.com/blog-entry-100.html
Anyone know if this applies to the 8125 as well? I've got a flickering white screen. I had dropped my phone a few weeks back and cracked the LCD. Replaced it with an OEM LCD - it worked fine for about 2 weeks and then just suddenly went all white. Phone still works, I can still get calls - just can't see who is calling.
I don't recall that the wizard had the same problem... Though from a logical point, it seems that there is an issue behind white screens and the thumbpad being responsible for it, so it may well be the same thing. Perhaps just disassemble the wizard (there should be a howto too) and check if theres a similar connection from mainboard to thumbpad circuit.
Is there a disassembling manual for a imate k-jam that anyone knows about?
Here's a website with a video manual i found useful...
http://viralelectronics.com/category/howto/page/2/
Figured out the problem...
The only reason I figured out the screen goes blank is because the motherboard loses connection with the screen when you slide the keyboard out...try this out and see if the screen comes back...
put the screen on sleep mode (no white screen)...then slide out the keyboard and tilt it a little hard after pressing on the screen and put the power on. if it doesnt work try again it might take some pressure and power to make it work...be careful not to put too much power but as far as I went, it's a very sturdy cell.
alternately, slide out the keyboard in sleep mode, and press all the buttons really hard and then try to press the power button (press more towards the space bar because that helps)...if any of this works and the screen comes back on even just for a second...follow the following
Go back to the person who gave the link to the site with opening the HTC instructions and follow through and clean the whole phone up from dirt around the screen and such...you dont need to put those rubber things or whatever it says to put on the screen...then when you are putting it back together, press hard on the wire connecting the touch screen to the motherboard. I suggest sealing it with a good tape...and then you are good to go! I did it but it had a few glitches...the screens contrast sometimes goes awry but it is still visible and responds to touch. Also, the physical buttons work as well!!
Good Luck and do it at your on risk.
Have any of you tried this? http://forum.xda-developers.com/showthread.php?t=321163
hope the best
i tried this and it worked for me. i also pressed alil hard around the d-pad and heard a pop. i think it poped back into place.
thanks
razor rc said:
i tried this and it worked for me. i also pressed alil hard around the d-pad and heard a pop. i think it poped back into place.
thanks
Click to expand...
Click to collapse
i still have this problem.
fixed my wsod
I noticed a few days ago my 8525 screen went white, rebooted and it went away. Today it came back, but would only go away for a few seconds and then back to white. After reading some forums I decided to check the connector. I took the phone apart following this site as a guide. I removed the connector on the board side and cleaned the contacts with a qtip and denatured alcohol. Phone has been perfect for the last few hours, no more white screen of death. I didn't mess with the connector on the LCD side, just the board side. I'm a computer tech and I found it quite annoying to disassemble, but I managed without causing any damage, however, I'd rate the job at about a 8/10 as far as technical ability.
Joey
warped0202 said:
I noticed a few days ago my 8525 screen went white, rebooted and it went away. Today it came back, but would only go away for a few seconds and then back to white. After reading some forums I decided to check the connector. I took the phone apart following this site as a guide. I removed the connector on the board side and cleaned the contacts with a qtip and denatured alcohol. Phone has been perfect for the last few hours, no more white screen of death. I didn't mess with the connector on the LCD side, just the board side. I'm a computer tech and I found it quite annoying to disassemble, but I managed without causing any damage, however, I'd rate the job at about a 8/10 as far as technical ability.
Joey
Click to expand...
Click to collapse
i agree that this is one of the first things to try in curing the white screen issue. Others may find their problem runs a little deeper and the contacts on the d/pad chip are broken. An improvised cure which may not be very permanent is to place a little padding on the surface of the chip as described here:
http://forum.xda-developers.com/showthread.php?t=321163
If you have appropriate heat gun equipment you can re-flow the solder on the d/pad daughter board - but remember to remove the sticky key pad layer or you'll cook it!!
I regret that I'm closing this thread because we have several "White Screen" threads and the questions and answers are being spread all over the place.
Please use this one for future posts:
http://forum.xda-developers.com/showthread.php?t=321163
Mike
Ok I need help from the gods of xda
I dropped my tilt the other day. When I picked it up everything seemed fine, yet the screen was completely white. No signs of cracks or a broken lcd. So I've tried the following: Soft reset, Hard reset, took out the battery, took apart the phone and disconnected the lcd and then re connected it. Still the same problem. WHITE SCREEN!
I can still receive/make calls, when i touch the screen in places where i remember the menus to be it still responds due to the noise, also the open and close noise still sounds.
The phone was bought new on Ebay, so i don't have a warranty through them or AT&T. After much research I hear people saying the same has happened to their phones as well and that there is a ribbon or flex cable problem. Something about still giving power to the LCD but not data, thus the white screen.
Now what I dont understand is do I need a new LCD because it has that ribbon/flex cable on it???? (link)
or
Do I need this product?(link)
Both contain a "flex cable" so im confused and frustrated, someone please help! any ideas would help
whew bought an LCD with digitizer on ebay for $45 and fixed it. Very easy process
vsicarbon said:
whew bought an LCD with digitizer on ebay for $45 and fixed it. Very easy process
Click to expand...
Click to collapse
hi there, would it be possible to post the link to ebay item? i also need a new touch-screen.tnanks
I am curious about this as well. I have a friend who has a hermes and he mentioned to me that that his screen was starting to go white like explained here. I look at his phone and I also noticed that the bottom hardware keys were not working at all.
I am wondering if this same ribbon cable for the LCD would also be the same one for the bottom keypad and if I fix the screen the keys will become active again.
Anyone have any experience with this?
Thanks,
I am wondering if this same ribbon cable for the LCD would also be the same one for the bottom keypad and if I fix the screen the keys will become active again.
Click to expand...
Click to collapse
That i dont know but here is the link to the LCD screen w/ digitizer
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&Item=350099750789&Category=162&_trksid=p3907.m29
Same product and vendor I got mine from. Shipping took 3 business days. I advice to buy the insurence
Park City said:
I am curious about this as well. I have a friend who has a hermes and he mentioned to me that that his screen was starting to go white like explained here. I look at his phone and I also noticed that the bottom hardware keys were not working at all.
I am wondering if this same ribbon cable for the LCD would also be the same one for the bottom keypad and if I fix the screen the keys will become active again.
Anyone have any experience with this?
Thanks,
Click to expand...
Click to collapse
Tuck in for a long read and perhaps no single answer for all cases:
http://forum.xda-developers.com/showthread.php?t=303872
In short, yes the d/pad cable and LCD screen connections are linked which is why it is not uncommon for the white screen to show up when the d/pad is not working.
To the OP - I would just point out that if you get the white screen after a fall it may just be a loose connection at the d/pad and no need for new parts.
Dismantling instructions here:
www.mikechanon.net
But let's not start discussing the white screen here, please use the first link I gave above if you need to post.
Mike
a user i dont recall now his name,fixed is whitescreen by replacing the camera,open the device and remove the camera module, reassemble to test.
Hi, peeps. Would like to ask for your assistance in troubleshooting my old T-Mobile MDA - the one that is also the Xda mini S.
The unit in question is 2nd hand although it was still in good shape when I got it. Used it for over a year already and has seen much use. Once, the insides got wet and I had to dry it out but it was okay after that. Although the keyboard wasn't showing any backlight until I figured out that a blowdryer would help remedy that situation (after careful dismantling).
Recently, the screen when you slide open the keyboard either comes up blank (whole screen is just white) or is discolored and a bit disaligned (the top part is either missing or is at the bottom of the screen). It happens too on the normal layout at times.
I upgraded the firmware with the most recent one I downloaded here last year. No problems experienced though with regards to the OS and not sure if the recent problem can be attributed to it.
Any ideas and suggestions?
I got the same problem on with the screen my Cingular 8125. When I slide the keyboard open, the exact same thing happens to my screen. Sometimes It only used to happen maybe once every 10th time, but as of last, it is happening all the time.
I spoke to someone at a repair store in Toronto and the guys said it will cost close to $100 to replace some wiring in the back. It didn't seem worth it for me so I got another phone instead, but I would love to keep using this phone if this could be replaced.
Hey guys. If you are comfortable, I would suggest dismantling the phone and taking a look at the ribbon connector between the board and the screen. My guess is that it is loose, or damaged. Reseat the ribbon and try again. Otherwise I would see if replacing the screen helped. Certainly much cheaper than a new phone...
Reseating
first of all check out the socket (on board) where the screen coaxial cord is plugged in , r all the connector pins alligned or are any bent / pulled back ?
in that case reset pins location using a tiny neidle or pin, also use a double faced adheisive tape on the back of the screen connector to rest it tight to keyboard (original setup only they use glue).
second check out if the screen does that if was flipped using software , if it was a hardware case and upper solution wouldnt help then check to see if the sliding mechanism (two plastic identical bars screwed by two screws each to the top and the buttom of the screen) are aligned and screwed tigh to the screen.
now the wizard hardware is a survivor but any tampering with it require tight reseating , screwing and later reflashing (even if the software showed unaffected).