I found this on another forum, Im about to try it out now just letting my wing charge.
"''T-mobile Wing Unlock
Just if your firmware version is HTC
Downloads Tools
http://www.megaupload.com/?d=3SL9ST2J
The method used is a little bit risky, because it involves flashing a special version of the radio stack to perform the unlock, but if you follow the instructions properly everything should be fine.
Note that the unlock procedure requires you to reflash your Universal. Although the unlocking procedure itself should be safe, you are advised to take a full backup of all device data before use.
1. Backup your phone (not necessary, but advisable).
2. Remove your SD Card.
3. Enter bootloader mode on your Phone. To do this, simultaneously hold down the backlight key (“bulb” key, next to volume key), the power key and soft reset the phone. Your phone screen should clear, and you will see very faint writing saying “serial”. Let go of buttons etc.
4. Connect your phone to your computer using the USB lead.
5. Run the MaUpgradeUt_noID.exe program – this will reflash your phone with necessary software required to enable the unlocker.
6. Wait patiently.
7. Once the MaUpgradeUt_noID.exe upgrade completes, soft reset your phone by pressing the soft reset button on the back of the device [if the flash has been successfully applied, you should see that you now have Radio version 0.00.00]
8. Allow your phone to reboot. Once it has, connect to your PC using Activesync, and copy the UNI_Unlock_v1.exe program onto your phone. Alternatively, copy it to an SD card and insert into your phone.
9. Run UNI_Unlock_v1.exe on your phone. Wait patiently.
10. Once the process completes, soft reset your phone.
11. Process is complete!"""
franknat said:
nice info, i found a site here u can get assistance for more details --spam removed-- here.
Click to expand...
Click to collapse
Why would you wanna check that out, for a fee?
its working????
Can someoane give me the file rilgsm.dll from windows directory from one unlocked herald wing(not sim locked)
TNX
That's for the HTC Universal man. NOT a universal unlocker. You could brick your phone trying this. BUT- if by some miracle of god it works, post back!
unlock wing
BLACK-ICE said:
I found this on another forum, Im about to try it out now just letting my wing charge.
"''T-mobile Wing Unlock
Just if your firmware version is HTC
Downloads Tools
http://www.megaupload.com/?d=3SL9ST2J
The method used is a little bit risky, because it involves flashing a special version of the radio stack to perform the unlock, but if you follow the instructions properly everything should be fine.
Note that the unlock procedure requires you to reflash your Universal. Although the unlocking procedure itself should be safe, you are advised to take a full backup of all device data before use.
1. Backup your phone (not necessary, but advisable).
2. Remove your SD Card.
3. Enter bootloader mode on your Phone. To do this, simultaneously hold down the backlight key (“bulb” key, next to volume key), the power key and soft reset the phone. Your phone screen should clear, and you will see very faint writing saying “serial”. Let go of buttons etc.
4. Connect your phone to your computer using the USB lead.
5. Run the MaUpgradeUt_noID.exe program – this will reflash your phone with necessary software required to enable the unlocker.
6. Wait patiently.
7. Once the MaUpgradeUt_noID.exe upgrade completes, soft reset your phone by pressing the soft reset button on the back of the device [if the flash has been successfully applied, you should see that you now have Radio version 0.00.00]
8. Allow your phone to reboot. Once it has, connect to your PC using Activesync, and copy the UNI_Unlock_v1.exe program onto your phone. Alternatively, copy it to an SD card and insert into your phone.
9. Run UNI_Unlock_v1.exe on your phone. Wait patiently.
10. Once the process completes, soft reset your phone.
11. Process is complete!"""
Click to expand...
Click to collapse
could you tell me some suggestion about how to unlock htc_t-mobile wing,because i still no clear about this. anyway please send me some pictures solve this
regarding.
If you would actually read the thread, or just my last post even, you would see that this is not intended for the wing, and I do not reccommend using it because it could destroy your phone.
THERE IS NO FREE SIM UNLOCK PROGRAM AVAILABLE FOR THE WING
That being said, here are your options if you want to get your wing unlocked:
1. Call T-mobile customer care at 1-800-TMOBILE or 611, as for the Smartphone/Pda department, and tell them you need your phone unlocked because you are going overseas for a week and you need to be able to use a foriegn sim card in your phone. They will email you the code in 48 hours. This only works if you have a T-Mobile account in good standing for at least 90 days.
2. Pay to have it done. That's what I had to do, because I don't have T-Mobile anymore.
tonyc0642 said:
That's for the HTC Universal man. NOT a universal unlocker. You could brick your phone trying this. BUT- if by some miracle of god it works, post back!
Click to expand...
Click to collapse
I must of forgot, sorry guys, But yes bottom line it didn't work, i must be doing something wrong. also no this dose not brick, it didn't brick my wing so its brick safe.
don't be cheap. contact Jocky Wilson.. he can solve ur problem!
BLACK-ICE said:
I must of forgot, sorry guys, But yes bottom line it didn't work, i must be doing something wrong. also no this dose not brick, it didn't brick my wing so its brick safe.
Click to expand...
Click to collapse
Yeah, it doesn't work because it's not for the wing dude. Its for the UNIVERSAL. buzz_lightyear is a moderator here who developed the unlocker and buzzdev is his site, linked in his signature. The Universal is NOT the wing, and the unlocker for it will not work on the wing. You aren't doing anything wrong, it's just not meant for your phone. See the original xda thread here: http://forum.xda-developers.com/showthread.php?t=266758
tramuyo said:
don't be cheap. contact Jocky Wilson.. he can solve ur problem!
Click to expand...
Click to collapse
It has nothing to do with being cheap. I don't think anyone should have to pay to have it done.
I totally agree with you man, I think it's totall bs, but they kinda have us by the balls here. I looked for MONTHS for unlocking tools, but there simply are none for the Wing/Herald. If you ever find anything let me know.
how much is it to unlock the Wing?
There are people around here on the forums that will do it, but I don't personally know any of them, and I don't get a guarantee either. I took mine to a local cell phone shop that I trust and had them do it. It cost me about $40, and it was worth every penny.
Related
I just bought a t-mobile wallaby from here in india, And i decided there was a update available after 3.14 or something. so i ran it. But it stopped in the middle. Said 20 min but waited an hour. Then i took the xda of its cradle and did a hard reset... Now all it does is switches on and show t-mobile and the light stay on...nothing after that. I think i really messed it up. Gave it to a guy who said he could fix it but now 4 days later says he cant. Really need help on how to do it myself Please. Please help me, cant throw money away like that......can some show me step by step instructions as i am stupid with upgraded or reinstalling this device.
why have you decided that you could upgrade your device if you don't understand anything to upgrading and its consequences.
Upgrading is *dangerous* for dummies.
You are the weak link[/list]
mananmistry said:
I just bought a t-mobile wallaby from here in india, And i decided there was a update available after 3.14 or something. so i ran it. But it stopped in the middle. Said 20 min but waited an hour. Then i took the xda of its cradle and did a hard reset... Now all it does is switches on and show t-mobile and the light stay on...nothing after that. I think i really messed it up. Gave it to a guy who said he could fix it but now 4 days later says he cant. Really need help on how to do it myself Please. Please help me, cant throw money away like that......can some show me step by step instructions as i am stupid with upgraded or reinstalling this device.
Click to expand...
Click to collapse
:x Forget what this guest just said we are a community who help each other out :x
I am now using the XDAII but when i had the XDA1 i had a similar problem. Got stuck upgrading. Hang onto your horses dude your device isn't dead so breath a sigh of relief. If you have a SD/MMC Card reader then use it to burn the base Rom from
http://lumpistefan.dyndns.org and then install it through the boot loader(Hold the Power button and then press the soft reset button using the stylus(you will enter the boot loader mode and then follow the instructions on how to install the Rom.
------------------------------OR--------------------------------------------
Go to a shop or a friend who had similar device, make sure you have a SD/MMC card with you and then enter the bootloader mode as described above and then copy the ROM on the SD Card. Then insert the card in your device and again enter the Boot Loader mode and Copy the Rom from the SD Card to your device after you are done press the Hard reset button on your device to switch it off keep it off for atleast 60 sec before pressing the hard reset button again to switch it on. Your device will live again.
[/b]A WORD OF ADVICE
Don't touch the Radio Stack on either your device or the other one. Always select Rom only.
If you need further help with using the bootloader search these forums you'll come up with alot of info.
Let me know how it works out
one question
Thanks for the advice.....your must be the better part of the site.
what happens if i cannot get into the boot loader.
thanks again
Re: one question
mananmistry said:
Thanks for the advice.....your must be the better part of the site.
what happens if i cannot get into the boot loader.
thanks again
Click to expand...
Click to collapse
I believe there's a way to go-back! Do a flush by pressing on the power button+the hard reset+the navigation button pressed. All at once and that's how you go-back to the original ROM. Let me know if it works and if you dare to do it anyways.. 8)
guest said:
why have you decided that you could upgrade your device if you don't understand anything to upgrading and its consequences.
Upgrading is *dangerous* for dummies.
You are the weak link[/list]
Click to expand...
Click to collapse
Mr. Guest you are an idiot, many of us have been at this point one time our another. This is no way to respond to a forum member in need of help.
i'm no techie when it comes to these things but just out of curiousity WHAT causes the upgrade to stop? mananmistry said he was in the middle of upgrading already; is it the rom he used or is it the connection (power flux, cable, sync, etc)? just curious... :wink:
oh and its beers for the others and the loo for the guest
update
now the thing is i got the phone back. I have connected the usb but pc cannot find device and xdatools or the rom .exe files wont install. it says "xda not found via activesync", something like that. I went into the boot loader and it said GSM ERROR and stops. have to press calender key to get into sub-menus. what is the problem. does the rom kitchen .exe files need sactive sync to be present. please can some one tell me.
do i need a sd card reader. can i not just use someone phone to put my sd card and burn onto sd...??
You are now in serious trouble, the GSM error often proves fatal for the phone. You can still flash the rom though by following the previous instructions. After that is completed you will have to try flashing a radio stack. Please be prepared to be disappointed, I wish you the best of luck. The good news is that even if the phone doesnt work you should still have a working pda.
Where can i get a radio stack rom...???
Click to expand...
Click to collapse
where can i get a radio stack rom....will try...
If my gf has a pda with sd card can i use the unit to see the sd card and write the rom on it???
Re: update
mananmistry said:
now the thing is i got the phone back.
Click to expand...
Click to collapse
how did U get the phone back 2 work (bootloader)
thanks
:?:
get a radio stack from here
http://lumpistefan.dyndns.org/tools/
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Zulu137 said:
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Click to expand...
Click to collapse
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Asfarizal said:
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Click to expand...
Click to collapse
Manage to solve the problem ...thanks WIKI !!
Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus
Then Flash to any ROM you want !!
Thanks .... But
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Thank You
I will follow the instructions you gave and try to get it going this weekend.
Thank you so much for your time
Zulu137 said:
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
Click to expand...
Click to collapse
Looks like you've got a lot of reading to do, and a problem to sort out. Firstly a couple of answers...
Schaps is a Rom Cooking guru (makes custom versions of WM5, WM6 etc). When you get your phone sorted out I'd recommend trying one of his roms.
Hard SPL. The SPL is part of the bootloader which effectively dictates how a rom is flashed and what roms can be flashed. HardSPL is a custom version of this which allows you to flash any rom from any carrier. It also protects against a bad flash in many cases. It is recommended before you try flashing any new roms or radio roms. Use Hard-SPL-V7 at the bottom of the first post here.
The Rom upgrading software is contained in any of the cooked or carrier supplied roms. It is normally a .zip file which cotains 2 files: xxxxxRUU.exe and RUU_signed.nbh. You run the .exe file from your PC when connected to your phone via USB. More details of how to do this are in MrVanx's guides. Also other resources here.
Now to try to sort your phone out...
What is displayed on your screen when in bootloader mode? It should be something like this:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro (This is HardSPL V7)
If you don't have an Olipro SPL then you need to get HardSPL onto your phone. If you haven't done any upgrading and have had the phone from new then I guess you don't have hardSPL.
Now you need to fix your USB Malfunctioning problem. I can't help too much here except to suggest trying a different cable, different USB port or different PC. Also, if you are running Vista try an XP maxhine. When you connect to the PC does your phone show Serial or USB on the screen? If you can't get a USB connection, all is not lost - you can re-flash your rom using an SD card, method here.
There is a thread about un-bricking phones which may help.
There are various diagnostic tools (which can also screw your phone if used incorrectly). The favourite of these is MTTY but you need a USB connection to use this.
If your phone is in warranty I'd recommend getting your supplier to sort it out, but if not I'd try to re-flash an ORIGINAL supplier rom (Cingular I guess). You can get links to the official supplier roms here.
I think (might be wrong) that sometimes when stuck in bootloader you need to flash an official rom, not a cooked one to recover your phone - then you can run HardSPL and then flash cooked roms again.
Cingular 8525 stuck in bootloader
Thanks for the reply ... lots of great input.
Now to answer some of your questions.
1) When I power up the phone (only pushing the power button ) it goes straight into the bootloader screen without pushing any other buttons, and it displays
HERM100
IPL-1.01
HERM100
SPL-1.06
Then at the bottom in the white bar it says "Serial"
The only way that i have found to power it down again is to remove the battery, there is no response from any single buttons after it is in bootloader
the soft reset and hard reset work but it just goes right back to the bootloader screen after.
2) The USB malfunction. This only started after the phone "crashed" and before that it worked great ... well i only used it to sync up to my work pc for the contacts and to get pictures onto my hard drive.
all the PC's that i use are running XP. I have tried my home PC and my Laptop
and the work PC and all of them have their own cables and they all say the same thing ... "the USB device is malfunctioning"
I am sure that when i get the phone going again the USB will start to function again.
3) Phone warranty ... I bought the phone off e-bay from a store in new york about 10 months ago as a "new unlocked cingular 8525" it was new and unlocked, but i have no idea how they unlocked it. I would assume that there would be no warranty now and in any case i live in Canada and would have to ship it down to the states to an AT&T repair center and that sounds like a nightmare to me with the customs and so on.
I will give you a little more background on the problem. the phone worked like a charm without any problems at all for the 10 months that i had it, then the morning of the crash the phones alarm did not go off in the morning and i was almost late for work ... i did not pay it any further attention untill at 3:26pm
that afternoon the alarm went off ??????? (it was set for 6:05am) so i checked the main clock time, it was right. I then checked the alarm time, it was right ??? So i figured that something must have just got confused, so i powered down the phone with the power button to just restart it and while it was powered down i removed the battery to take the oportunity to to clean all those fuzzies and dust that collect in the battery compartment out and put it all together and powered it up again (just by pushing the power button) and this wierd red, green, blue and white screen appeared and that is all that i have seen since ???
I hope that answers your questions and i will start going through the links that you sent and get to reading ... will there be a pop quiz ... lol
Thanks again for your time and i very much appreciate all the time that all of you have spent on me and my phone ..... I know that you all just feel bad for me because i now have to use a Motorolla V551 ... lol
Great Work
ultramag69 said:
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Click to expand...
Click to collapse
Thanks a lot man & great work i unbricked my Herm100 with method u mention above thanks a lot & great job keep it up
I also have this problem.
I d/l Hard-SPL-V7
and when i run RUUWrapper.exe
I get an error saying the application failed to initialize properly (0xc0000135)
What's going on?
How do i fix this?
this happened when i was trying to unlock the phone.
Thanks
need help
when i switch on my orange herm100 it shows On the bootloader screen is displayed:
HERM100
I PL-1.01
HERM100
SPL-1.40.01ipro
history : i buy unlocked orange phone
fewdays back i found no imei ,
yesterday i try to flash by micro sd but in gsm stage its gets hang no progress after extrom stage
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM - (NO ACTION)
OS -
i tryed several time no action, i cant connect by mini usb.
PLEASE help me
tell me which it the right rom to chose? step by step procedure..
how to rectify imei?
thanks and regards
kirtibas
kirtibas, sorry it took so long to reply, 1st thing I'd do is upgrade to SPL 2.10 olipro. This is safer to use than others. then I'd suggest reflashing a stock rom to see if that works. After stock rom works then use a cooked rom as your heart desires... Cheers...
Okay I'm having problems with my wizard.
It freezes at the splash screen.
It won't hard reset "Format is Failed"
And flashing billions of roms does no good.
Here's a solution that's supposed to work
http://forum.xda-developers.com/showthread.php?t=276963
but your device has to be cid unlocked wich mine aint.
And I can't unlock it with lockwiz, because it won't start up.
I could use imei-check, but don't want to pay 40$
If you follow the instructions in the link above and send me the minisd so I can reset my wizard, and it works, then I will return your minisd with a 10$ check.
Leave me a message if your interested in helping.
But, because i don't want a billion people sending me blank minisd cards I'll only pay if it works. If it don't I will still return the minsd.
Please help a guy out.
Thanks.
Cmd1991 said:
If you follow the instructions in the link above and send me the minisd so I can reset my wizard, and it works, then I will return your minisd with a 10$ check.
Click to expand...
Click to collapse
I faced the same situation with my wizard..The only solution is to pay the 40$. If the device is not CID unlocked it can not boot using the sd card.
I unlocked my phone using imei-check and then my wizard worked like a charm.
It is simple: If you do not pay for the CID unlocker your WIZARD will rest in peace for ever..
Have you tried this? http://forum.xda-developers.com/showthread.php?t=294107
Maybe your SD is to blame. Try it without the SD and you may get lucky. If it works I would format the SD card before rebooting the phone.
Okay so i just realized it has to be cid unlocked even to back it up from the minisd.
So does imei check work with phones in the U.S.?
Anybody know?
bootloader?
what version of the wizard do you have? (what does the ipl/spl stuff display?)
try holding the camera button down when starting up to enter the bootloader, then connect the usb cable and flash.
Good luck!
Matt
1.Download the original/official WWE ROM from your provider's website
(you may need to register the phone with the provider online to be able to download the ROM- usually the phone registration and official ROM download is free)
The WWE ROM allowes the device to be reflashed - even if the phone is CID locked.
2.Connect the phone to any XP machine using USB
3.Start the phone in bootloader mode (3 colord band with IPL/SPL in top left and USB in bottom left will be displayed)
To start in boot loader mode -->Press and hold the camera button, simultaneously press the soft reset button with stylus.
[Soft reset push button is located in the middle of camera button and infrared port (close to infrared port)]
4. Re-flash the phone by running the dowanloaded ROM from USB connected XP machine.
Hope this helps.
I earn 10 pound men
I have your answer BUY A NEW ONE!!!!!!
hahahahaha
Like ungry dogs huh?! 10 pounds .-.- 10 pounds
If you can get your phone into the bootloader(hold camera then soft-reset), you could try to flash it with:
ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
maybe that will work, if its flashed successfully you can cid unlock your phone, good luck.
I unlocked a Cingular 8125 and went to load TNT Professional ROM. The phone kept losing communication at 99% and when I went to reload the original ROM from HTC's site, now I have NO O/S. I DO have another one, but my wife is using it until we get her a pink BlackJackII. I really like these phones, and can't believe I crashed this one! I don't have any Mini-SD cards. Any way to rebuild this thing?
Nobody has any ideas for me? I really need to get this phone running again!
Your not using Vista are you?
Most comm errors are due to weak or discharged battery,not having enough juice to complete the the flash,get it fully charged and try again,secondly,Yes! don't use winVista.
Download the official stock rom and flash to recover back.Get the phone in Bootloaders (RGB screen) hook up the phone and watch small usb appear at the bottom of the Bootloaders,if its there,run the rom to flash,it'll start to flash,but if small usb is not present than most probably its a comm fault.
I was using a Win2K machine. I had 2 batteries that were fully charged. I have a friend that will lend me his miniSD adapter and use my 1gig microSD card to get the info off my wife's phone and copy it to this one. He has a Sprint version of the AT&T Tilt. Might see if he wants to check out this site.
OK. I have access to a miniSD card now. Do I just take my wife's 8125, make a backup from it, then put the card in the bricked phone and load bootloader?
Read this thread for more specific instructions :-
http://forum.xda-developers.com/showthread.php?t=276963
But this method will only work if both the devices are already CID unlocked.Secondly,most important,both the devices shud be of same DOC Chip version,G3 or G4.If you back up a rom of G3 on a G4 device,it'll brick it and vice versa,make sure both the devices are of same DOC Chip version.
They are both G3's. I think they may even be from the same batch. If I unlock hers, won't I lose all her data?
YUP ! but first make a back up of all the personal data on her phone to your pc,for this use either 'PimBackup' or any similar back up application and than unlock it.Its necessary to have both phones CID unlock,otherwise,this method won't work.
OK, I used Lokiwiz 3beta and superCID unlocked the other one. When I run mtty, and use the r2sd all command, I get
R2SDBackup()-Download type=5
usTotalBlock= 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
I have left it sitting there for an hour and nothing else happens. Isn't it supposed to have several more lines of text scroll by? Also, I can't figure out how to get the dead one to boot to the miniSD.
ok,did you read the method carefully,the link I posted above ? you are getting it correctly.
This methods involves many steps.
Step 1.
Back up all the data on your wife's phone to your pc with 'PIMbackup',than downgrade to IPL/SPL 1.xx either through flashing 'Button's Rom 1.05 or you can even flash official stock rom Aku1 for this,when getting IPL/SPL 1.xx either way,apply lokiwiz02b and not lokiwiz 3beta to CID unlock your wife's phone,or you can use WST_4.2.2 tool also to CID unlock it,but its must to have IPL/SPL 1.xx to CID unlock in both the ways.Only after getting the phone CID unlocked,you can Backup the rom on a miniSD card.
Step 2.
After successfully back up of the rom on miniSD card,insert this card in your dead phone and get the phone into Bootloaders mode (RGB screen).
Step 3.
Run the MTTY command to back up from miniSD card.This is only possible if you already have this phone CID unlocked,otherwise it won't work.
Both the devices must be CID unlocked.
Although,I'm still not sure if it works,but there's no harm to try,may be it gets going.
Is the progress bar supposed to change back and forth from blue-green to red while flashing?
YUP ! it changes during flash,but it'll become green on 100% completion and the phone reboots.
OK. I can't get this thing to take the WizardLove ROM, can't find Button's ROM, but I am trying to load the XDAMiniS ROM now. On my third try and the SPL still says 2.25. Battery is fully charged and I get an immediate connection failure trying to load WizardLove. I really wish I could find the original Cingular ROM for this phone, not the new(er) update.
Download Cigular official stock rom from here :-
http://www.htcamerica.net/support/8125/software-downloads.html
or
http://download.america.htc.com/RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe
Check out this link for all the Roms like Buttons Rom T-mobile 2.26 etc
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
I am just about ready to give up on this thing. No matter what I do, when I try to boot it up regular, it still keeps freezing up and when I try to do a hard reset, I get a format is failed error message.
Last ditch effort
Can I use WST to make a backup RUU from the working phone and flash that to the dead one? All other attempts have failed to restore this phone.
I dont think so
Men you are already doing everything!!!
Does you have mtty... try this please it may works for you let us know what happend please...
http://forum.xda-developers.com/showthread.php?t=420785 the man in this thread stucks on splash screen so read just the mtty steps.
BTW does you unlock your wife's phone... is yours unlocked too? before do it...please respond.
The hope dies at the end!!!!! we have so much to´pics about this issue... why you are runing windows 2000? nad make upgrades? or does I missunderstood? extremely recomended Win XP.
I have Vista at home, and I read where many people here say that you can't do reflashes with Vista, so I use my computer at work, which runs Win2K. I haven't unlocked the second phone, but I thought that I did the first one. That was why I went to flash it. I wonder if the unlock didn't take and that put me in this predicament.
I understand now
Maybe a mistake using windows milenium or 2000 or whatever...
So if it say format failed i cant imagine other thing that do the thing i post you... so if you got questions about clear DOC Chip ask everything...
when you already get everything in a XP machine tell us please oh just for a recomendation unplug the minisd and during the process the mtty working on some lines dont launch programs check your USB cable maybe with a little scratch and moving makes a false contact at all.
Ok, Well I Unlocked my HTC Surround so I could update. I did the whole process and then I was on NoDo update! I was very happy, But then I wanted to Restore it so I could Sideload once again. So I started the restore and the percentage Hung at 0, and Then I got error code 801812E0! so I was like ok I will just not sideload for a while..
Then I boot up my phone and a Picture of a phone Pops up with a usb saying connect to your PC (It didnt really say it.. you know what I mean) So. I plugged it in to my PC again and it said to restore it... So I said ok and I got the same Error 801812E0 Now I cannot use my phone Please will someone help me.
Also I am only 15. My Parents will be very pissed if they found out what happened.. but I need to get this working ASAP.. I cannot call ATT Ive tried everything.. Please someone respond
I think you should reflash your phone in order to get it work.
Go here: http://forum.xda-developers.com/showthread.php?t=943714 and download your compatible rom, then reboot it into bootloader (Power + Volume Down), connect to PC, and reflash ^^
Hope it help
Thank you for your concern, but How am I supposed to figure out what type of ROM I need if I have no access to my phone to see? Haha
funnydude35 said:
How am I supposed to figure out what type of ROM I need if I have no access to my phone to see? Haha
Click to expand...
Click to collapse
Use the Cingular ROM. I flashed my Surround from AT&T and it went OK, the ROM reverted to 7004. After that you can unlock your phone using ChevronWP7, use the fix to prevent it from re-locking again and then update to NoDo.
The rapidshare link from Ansar's post is down. I uploaded the Cingluar ROM to multiupload so you can fix your phone. Download it.
The instructions to flash your phone are as follow:
1. Unzip your downloaded *.zip file in a separate folder
2. Press and hold power-on/off button to power-off the phone
3. Press and hold volume-down button and then press power-on/off button to enter bootloader mode
4. When your phone enters the tricolor screen bootloader mode, release volume-down button
5. Connect your phone to your windows 7/vista/xp pc/laptop with a usb cable
6. Verify that your phone will be identified and relevant drivers will be installed by windows os of your pc/laptop
7. After completion of (6.) above, check the usb message connection on your phone screen
8. To flash the new ROM go to your pc/laptop folder of (1.) above
9. Double click on the ROMUpdateUtility.exe file and strictly follow the instructions on your pc/laptop screen
Click to expand...
Click to collapse
Please remember not to interrupt the flashing process! Do not disconnect the phone or play with it while it's being flashed. Try avoid using your computer at all and close all other applications before starting.
ertz, Noob here. I updated with the chevron updater and it seems that may be problematic. I'm using an at& branded surround will flashing the cingular rom allow me to recieve updates through zune?
gentry33 said:
ertz, Noob here. I updated with the chevron updater and it seems that may be problematic. I'm using an at& branded surround will flashing the cingular rom allow me to recieve updates through zune?
Click to expand...
Click to collapse
I'm pretty much a noob too, I just learnt a thing or two in the past few weeks
You will have no problems at all with your carrier if you flash your AT&T phone using the Cingular ROM. The SIM-lock will stay the same as it is (either locked or unlocked,) the phone will return to its factory settings.
Being restored to its factory settings will mean that you'll get the updates through Zune when AT&T decides it's time for you to get them. You can, however, unbrand your phone to receive the updates almost as soon as they're released. Remember that you'll need to "developer unlock" your phone before you can unbrand it.
I have my SIM-unlocked Surround on Movistar (Argentina carrier) and I can get the updates through Zune after unbranding it. No Chevron Updater or other hacks to get the updates.
Thank you guys for your help <3 I Actually just went and traded it in for another one If this happens again I will use this method Thank you much!