Network selection hierachy - Wifi vs GPRS (Kaiser) - Networking

When I'm in the house (and assuming I've got the wifi switched on on the Tytn 2), how do I get it to use the Wifi to access the Web as a first option?
Even when its connected to my wireless LAN (which it does with no problems at all - much better than my old Wizzard), if I launch Explorer it automatically makes a GPRS connection. The only way to force it to use the Wifi seems to be to turn the Phone off in the comm manager - which then means I can't receive any calls.
I can't find any setting that dicates the network hierachy i.e. that says if there is a Wireless LAN connection then don't bother with GPRS, or if there isn't, then use GPRS.
I seem to recall there was something similar on desktop Windoze where you could have it automatically use a dial up connection if there was no LAN available.
Can anyone help?

Iain.m said:
When I'm in the house (and assuming I've got the wifi switched on on the Tytn 2), how do I get it to use the Wifi to access the Web as a first option?
Even when its connected to my wireless LAN (which it does with no problems at all - much better than my old Wizzard), if I launch Explorer it automatically makes a GPRS connection. The only way to force it to use the Wifi seems to be to turn the Phone off in the comm manager - which then means I can't receive any calls.
I can't find any setting that dicates the network hierachy i.e. that says if there is a Wireless LAN connection then don't bother with GPRS, or if there isn't, then use GPRS.
I seem to recall there was something similar on desktop Windoze where you could have it automatically use a dial up connection if there was no LAN available.
Can anyone help?
Click to expand...
Click to collapse
I'm now getting the same thing using Emoze - the thing is sitting here connected to the Wifi & will sync mail & contacts etc over the wifi quite happily - but as soon as I try & send mail from the handheld it starts up not one but two GPRS connections (!) Much the same as if I try & get a web page up - it automatically goes to GPRS as its default route to the internet despite that fact that its already connected via wifi & the only way to stop this behaviour seems to be to switch the phone off in Comm Manager.
Seems to be something inherrantly odd about the way the Tytn 2 is deciding what network connection is available & which it should use. It looks like it needs a little control application to sit between the IP stack & the hardware so that when a request comes it can be routed according to user preference - i.e. Use WIfi if available, Only use GPRS etc The Wifi doesn't seem to fire up a connection when it feels like it - only the GPRS. Do all the HTC devices with WIfi behave this way?
In the meantime, does anyone know of a simple way to turn off/disable GPRS without disabling the phone?
WHile I have plenty of GPRS data allowance in my package when I'm in the house at my desk (or anywhere else I can get a wifi connection) I'd rather it just used the Wifi to sync itself or if I decided call up a web page.
Besides, it interferes with the hi-fi speakers in my study with that annoying buzzing noise everytime the GPRS gets busy.
I.

Hi guys,
I use 3 different wifi networks during the course of a day, well 2 a day, 3 through out the week probably. Home/Work/Friends house
I have a very small data package (5mb) so i am very choosy about when I use my data connection!
Anyways, did some testing.
I already know that if I have no wifi, no data connection on, then I try and start outlook or Internet Explorer, then my data connection starts up (as it should)
now if i have my data connection on, then i turn on wifi on the phone, the wifi connection takes over and the data connection is not being used, even though it's on.
I also have no problems with when wifi is on and data is off, and if i goto outlook or IE, that gprs decides to go on. this does not happen tome (unless for some strange reason wifi cuts out, gprs tries to take over)
So i dont know if its something with your settings or not, maybe your phone goes to sleep and wifi turns off then gprs takes over, or i could be misunderstanding your question, because now that I think about it, perhaps you are asking something like..
- at home no wifi or data connection is active at that moment
- you navigate to a page in IE and instead of gprs turning on, wifi turns on/scans for lan and uses that
Yeah, that's probably waht you are asking.. haha yahoo for long winded useless post
If you figure it out, i want to know! lol

Iain.m said:
I'm now getting the same thing using Emoze - the thing is sitting here connected to the Wifi & will sync mail & contacts etc over the wifi quite happily - but as soon as I try & send mail from the handheld it starts up not one but two GPRS connections (!) Much the same as if I try & get a web page up - it automatically goes to GPRS as its default route to the internet despite that fact that its already connected via wifi & the only way to stop this behaviour seems to be to switch the phone off in Comm Manager.
Seems to be something inherrantly odd about the way the Tytn 2 is deciding what network connection is available & which it should use. It looks like it needs a little control application to sit between the IP stack & the hardware so that when a request comes it can be routed according to user preference - i.e. Use WIfi if available, Only use GPRS etc The Wifi doesn't seem to fire up a connection when it feels like it - only the GPRS. Do all the HTC devices with WIfi behave this way?
In the meantime, does anyone know of a simple way to turn off/disable GPRS without disabling the phone?
WHile I have plenty of GPRS data allowance in my package when I'm in the house at my desk (or anywhere else I can get a wifi connection) I'd rather it just used the Wifi to sync itself or if I decided call up a web page.
Besides, it interferes with the hi-fi speakers in my study with that annoying buzzing noise everytime the GPRS gets busy.
I.
Click to expand...
Click to collapse
You should be able to use the comm manager to turn off the data connection, but as for keeping it off permanently, until you decide you want it to be even allowed to be active again maybe you can try this, it should disable your connection until you see fit.
http://www.modaco.com/content/Pocket-PC-Software/246171/New-FREE-Utility/

briggs81 said:
You should be able to use the comm manager to turn off the data connection, but as for keeping it off permanently, until you decide you want it to be even allowed to be active again maybe you can try this, it should disable your connection until you see fit.
http://www.modaco.com/content/Pocket-PC-Software/246171/New-FREE-Utility/
Click to expand...
Click to collapse
Great little utility , thanks very much for pointing that out - it at least allows me to do what I want manually - i.e. use my wifi without having to turn the phone off.
Although I know you can disconnect GPRS from the Comm manager, it also doesn't seem to have an idle time out so once an application (like Emoze) has started it up it keeps running in the background. Also, as soon as you turn it off, inevitably Emoze turns it straight back on! The NoData application gives much more control so thanks for that.
I do go abroad reasonably often so also happy to be able to use it for its primary purpose of disabling GPRS whilst roaming to avoid silly charges
It would be great if HTC could build a bit more intelligence and control into the network side of these things though.
I.

You may want to look into Schaps Advanced Config or KaiserTweak for wifi/gprs settings.
You can set timers and disconnects, etc, with those applications.

Iain.m said:
When I'm in the house (and assuming I've got the wifi switched on on the Tytn 2), how do I get it to use the Wifi to access the Web as a first option?
Click to expand...
Click to collapse
The Good News: I fixed this behavior on the phone w/o any 3rd-party utilities, etc.
The Bad News: I'm not 100% sure how. :-/ My apologies. Here is what I think did it:
Make sure your browser is closed and you have no open data connections.
1- Open the Wireless Manager and make sure "WLAN" is on and "Data Connection" is off.
2- Go to Start>Settings and choose the "Connections" tab along the bottom.
3- Open "Wireless LAN," choose your home wireless network, and make sure you're actively connected to it (should see a signal quality meter, device network settings, etc).
4- Close "Wireless LAN" and while "Settings" is still open and on the "Connections" tab, open "Wi-Fi." Your list of known Wi-Fi networks should be showing: make sure your home network says "connected."
5- Close everything back out to your "Today" screen.
When my Tilt is set this way -- and actively connected to my WLAN -- the Wireless Manager grays out "Data Connections" and doesn't even respond if I tap the icon. IE automatically uses my WLAN, although it won't connect to some of its pre-loaded favs b/c, I think, they're on WAP servers and the Wi-Fi/NAT router assigns/negotiates TCP/IP protocols for your phone.
I think now I accomplish all the above by simply opening the keyboard and pressing the FN/Wi-Fi key.
FYI -- In truth, I solved this problem by installing Opera Mobile and setting it as my default browser. Opera Mobile is a full browser, i.e. doesn't use WAP.
Hope this helps. If not, sorry for this 5 minutes of your life you'll never get back. :-/
gT

Related

set Wifi to SOLE default for web browsing?

OK, this 8125 is pissing me off. I want to use Wifi *exclusively* for web access. I don't want this thing to *ever* connect via GPRS, but I have no idea how to set it that way. I've searched but don't find anything along these lines, is there an easy way to do this?
Thanks!
Jason
well i have mine set that way "i think"
also i believe, someone else can chime in, as long as WIFI is turned on via the comm manager, its gonna overrule any other connection type like gprs or edge.
then what i did was go to to settings>connections>connections and make sure the first one selected is My ISP. then under your Wireless Lan connections settings, under the Power Mode tab, set that to best performance.
after that all I ever see up top is the WiFi icon. and if im not in a hotspot, E is there, but if i press explorer it just takes me to the media net page to login, so no data gets used anyway.
Dont know about 8125, but on my T-mobile MDA, I went to
settings->connections->connections.
There I deleted the configuration which had GPRS. Now my device tries to find wifi network or gives up.
Deleting the GPRS settings seems a bit drastic. Is there no way to say have separate "profiles". That way you could have a wifi only mode, and then when absolutlely necessary you could still use GPRS. I would be very interested in a solution like that, bit more flexible I think.
yes, wifi does take the default connection.. it will only try to use edge if there is no wifi connection present.
Or you can use the Registry Wizard and on page 4 select GPRS off...

How to stop my wizard\Qtek 9100 from dialing while I am connecting to wi-fi?

How to stop my wizard\Qtek 9100 from dialing while I am connecting to wi-fi?
I was testing my wireless the other day and evey time I did a search on internet explorer it seemed to be connecting to my net work provider.
Do I need to do something when I am using my wi-fi so it dos not connect both to wi-fi and to my network provider?
And can I down load Skype for my phone? And dos it work well, is it worth doing if I can?
if some one come back to me THANKS
Lucky for you, ive been working on this lately and just figured it out. Here's how to eliminate your wizard's annoying attempts to connect to services that you don't have.
Disclaimer: this will work for sure only on WM5, and ONLY IF YOU USE WI-FI AS YOUR SOLE SOURCE OF WIRELESS INTERNET CONNECTIVITY. it is not intended for those excessively wealthy folks who actually have $40 a month to blow on a ****ty, 56k-esque GPRS/Edge connection from their cell service provider, and almost certainly will cause lots of problems if you do decide to get this service in the future.
1. Go to settings, then connections, then connections again (there's a connections submenu in the connections menu)
2. Tap the advanced tab at the bottom of the screen
3. Hit the select networks button
4. Go to one of the drop-down menus, it doesn't matter which one
5. Pick the first connection, hit edit.
6. Hold the stylus down on each entry you see then select delete
7. Hit ok, repeat steps 4-6 for each and every connection listed.
Now your phone won't have any connections besides wi-fi configured, which means it won't try to fall back on them and annoy the hell out of you whenever your wi-fi drops.
Also, get a different browser, Opera or NetFront work well. PPC internet explorer keeps you from viewing the real version of web pages and limits you to the cruddy PPC versions (if they exist at all)
pee said:
Lucky for you, ive been working on this lately and just figured it out. Here's how to eliminate your wizard's annoying attempts to connect to services that you don't have.
Disclaimer: this will work for sure only on WM5, and ONLY IF YOU USE WI-FI AS YOUR SOLE SOURCE OF WIRELESS INTERNET CONNECTIVITY. it is not intended for those excessively wealthy folks who actually have $40 a month to blow on a ****ty, 56k-esque GPRS/Edge connection from their cell service provider, and almost certainly will cause lots of problems if you do decide to get this service in the future.
1. Go to settings, then connections, then connections again (there's a connections submenu in the connections menu)
2. Tap the advanced tab at the bottom of the screen
3. Hit the select networks button
4. Go to one of the drop-down menus, it doesn't matter which one
5. Pick the first connection, hit edit.
6. Hold the stylus down on each entry you see then select delete
7. Hit ok, repeat steps 4-6 for each and every connection listed.
Now your phone won't have any connections besides wi-fi configured, which means it won't try to fall back on them and annoy the hell out of you whenever your wi-fi drops.
Also, get a different browser, Opera or NetFront work well. PPC internet explorer keeps you from viewing the real version of web pages and limits you to the cruddy PPC versions (if they exist at all)
Click to expand...
Click to collapse
All I can say is that with diagnostic skills like that thank God your not a doctor!!
Just-In
I had a similar problem over the Cristmas period where even though I had a good WiFi connection my Wizard insisted on trying dial up a GPRS connection (even though it is set as always on). I never got to the bottom of it as I decided to give Faria's 3.2 ROM a try. It has never happened since.
With regards to the Skype thing, if you go to skype.com there is a model specific download for one of the Wizard variations I can't remember which one it is but you will recognise it when you see it. It works a treat when I am on WiFi and most of the time with Edge but it only works with the headfones connected otherwise the sound comes out of the main speaker.

Cingular 8525 - Can we disable GPRS/EDGE and use only Wi-Fi ?

Is it possible to setup the 8525 so that it only connects to internet through Wi-Fi and not any of the other options? Based on some threads, it looked like Cingular has disabled this option, but I am not quite sure. Thanks.
The only way I was able to do it was to call Cingular Tech and have them disable the GPRS on their end, now if I go to PIE and the WiFi is off, the GPRS/EDGE Connection pop-up opens, then I get an error message saying the network could not be found and a dismiss icon....
The only way it will connect to IE is through WiFi now.
ringostar said:
Is it possible to setup the 8525 so that it only connects to internet through Wi-Fi and not any of the other options? Based on some threads, it looked like Cingular has disabled this option, but I am not quite sure. Thanks.
Click to expand...
Click to collapse
if you go to settings then connection and delete the connection settings for gprs it will not connect and you can use wifi only
however i seem to keep getting gprs not connected error if i do so?
I'm having the same problem. I'm totally green to the high tech world. Heck this is my first attempt at anything greater than using my calculator function in a phone So if someone could walk me through what I need to do to set my phone up so I can connet through wifi i would reaaaally appreciate it.
I had Cingular put me on the no data plan (not even pay per use). In case that makes a difference.
Thanks in advance for the help.
All I did was go in to the connection settings and change the User name and Password. I do not get any error messages stating the network cannot be found. I get a login screen with User/Pass and Domain. I just click cancel and it drops back to IE.
Now I do not have to worry about accidentally connecting to their service.
well,we can very much achieve it -- In the internet settings in connections,select both of them to My ISP,edit it to nowap.cingular.com
Make sure setting is set to Internet,not work!
I did it and I use only wifi all the time!!
The previous solutions are not really workable for me since I don't want to delete my cellular data connection, I just want to be able to turn it on and off as I choose. With Windows Live, I can have a Wifi connection and turn off cellular data in the comm manager screen and it will just open the cellular connection again.
A hack to turn off the "auto connect" for the cellular data would be great. Make it like the BT or WIFI, where I have to go to the comm screen and turn it on. That choice would be great.
Anyhow, I am thinking of making the Work connection as the default, then deleting all work connections. Then when I actually want a cellular data connection, I could manually select it and say connect. I'm not sure if the applications will close it and try the work connection again or not. I will try it and post again, probably tomorrow.
MM
This works wonders:
http://www.benrichards.co.uk/?p=180
ETA: This is what I have been using to deal with gprs autoconnect on my 8525 and it's perfect for my uses. You just start the program and toggle on or off the data connections.
Gprs Disable
It really works thanks for your research

How do you force WiFi connection ?

Reflashed my Jade from UK Orange to JADEMAN rom recently...
I don't think this is a ROm related problem (unless you know otherwise !) so I have posted in general part of forum.
Can anyone tell me how to force the phone to use Wifi to connect to the internet.
It connects via GPRS fine but i want to disable the GPRS DATA for travels abroad so I don't run up a huge data bill. I can stop the data with "NoData" app, but if I now try to connect to internet with Opera or Internet explorer if fails..
Is there something I am missing, to tell it either to connect via wifi before using GPRS data or to only connect via wifi. Do I need to create a connection ?
The create new connection page doesn't list using WiFi, bluetooth is the only "WIRELESS" type connection that appears to be offered.
Also when the wireless AP list is shown and I try to connect to an AP showing available that I have previously setup with WEP key etc, it fails to connect.
I am sure to be missing something but I can't spot what the problem is...
Any help appreciated.....
Phil
Normally Windows Mobile connects via WiFi first, if available, and only when not present it uses GPRS. That means that you do not need to disable GPRS if an WiFi-connection is established.
I have no personal experiences with "NoData". Perhaps someone else can help.
phil-w said:
Can anyone tell me how to force the phone to use Wifi to connect to the internet.
It connects via GPRS fine but i want to disable the GPRS DATA for travels abroad so I don't run up a huge data bill. I can stop the data with "NoData" app, but if I now try to connect to internet with Opera or Internet explorer if fails..
Is there something I am missing, to tell it either to connect via wifi before using GPRS data or to only connect via wifi. Do I need to create a connection ?
The create new connection page doesn't list using WiFi, bluetooth is the only "WIRELESS" type connection that appears to be offered.
Also when the wireless AP list is shown and I try to connect to an AP showing available that I have previously setup with WEP key etc, it fails to connect.
Any help appreciated.....
Phil
Click to expand...
Click to collapse
MvBoe said:
Normally Windows Mobile connects via WiFi first, if available, and only when not present it uses GPRS. That means that you do not need to disable GPRS if an WiFi-connection is established.
I have no personal experiences with "NoData". Perhaps someone else can help.
Click to expand...
Click to collapse
AFAIK the moment you invoke any app that requires internet connection (weather update, activesync, opera) Jade invokes data connection first (3G, GPRS, etc) That's how it works on my set. Unless you invoke Wi-Fi connection first, then data connection is ignored.
I have had a bad experience that even if all setups are ok Wi-Fi conn thru Ap fails.
Corrected such a way;
Under 'Wireless /Lan' settings
Power mode should be brought to 'best performance'
azahidi said:
AFAIK the moment you invoke any app that requires internet connection (weather update, activesync, opera) Jade invokes data connection first (3G, GPRS, etc) That's how it works on my set. Unless you invoke Wi-Fi connection first, then data connection is ignored.
Click to expand...
Click to collapse
That's what I meant: You have to activate WiFi by yourself to prevent jade using GPRS (etc.). Your description is more precise, I did not make it clear enough. Thanks for correction.
Hi and thanks for replies so far...
I have just done a hard reset to make sure I haven't loaded anything that may mess up the wifi connection... Even when wifi is on and I am connected to a wifi access point OK it still uses gprs/3g not wifi..
Back to the "drawing board" I think...
Any more ideas please...
Phil-w
with this app you can disable or enable data connections as you please.
there is another app here in the xda that will disable data when roming automatically, but i don't remember the name.
faria said:
with this app you can disable or enable data connections as you please.
there is another app here in the xda that will disable data when roming automatically, but i don't remember the name.
Click to expand...
Click to collapse
Hi faria
Unfortunately I find it better to go into connection manager, select airplane mode, then enable wifi. Then do any surfing, live messenger etc. Then once finished go back into connection manager, re-enable phone.
Like others, I'm on Orange, wifi no longer stays the internet source even if it is connected. I have it on all the time, but if I use the internet, I have to go through the above procedure or it costs me credit through Orange.
Janeway
janeway said:
Unfortunately I find it better to go into connection manager, select airplane mode, then enable wifi. Then do any surfing, live messenger etc. Then once finished go back into connection manager, re-enable phone.
Click to expand...
Click to collapse
The only disadvantage is here is that, you'll miss calls when there are incoming calls because your phone is inactive (while PDA is). You can just disable data connection (CommManager - Data Connection - off) and leave wi-fi connected.
Like others, I'm on Orange, wifi no longer stays the internet source even if it is connected. I have it on all the time, but if I use the internet, I have to go through the above procedure or it costs me credit through Orange.
Click to expand...
Click to collapse
Just wondering.. how you identify which connection is being used, wi-fi or 3G/GPRS when both are connected.
What if you disconnect data connection (3G/GPRS) without activating the airplane mode, can you surf using wi-fi connection.
One possible reason - set connected to the AP via wi-fi but AP is not connected to internet, thus set seeks 3G as another route to internet.
Hi azahidi, thanks for taking time to reply to me . Your points as follows:
Yes, missing calls is the disadvantage, but I use my pda more for data and hardly any calls, so not so important for me, but obviously we be much better if that were possible as I do sometimes forget to swich back. If I disable the data connection, it automatically re-initializes itself as soon as ANY data is being transmitted - even with just wifi active - except when it is in airplane mode. This is a new thing for me with the Jade, didn't have that problem before with my previous HTC phone.
There is an icon for the 3G - when its in use it shows it - it goes from being a large G in a square to a smaller one with signal bars.
Wifi is definitely connected, I surf online with it all the time.
Its like 3G has priority over wifi - there should be a way to change that.
Hope the above makes sense.
Janeway
I'ven been using 'Nodata' succesfull the last past months, it does it's job well, but i'm not on Orange as you are, that might be the difference.
Just to be sure i've also changed my settings:
start > settings > connections > connections > advanced > select network > My work network (twice).
and
start > settings > connections >advanced network > uncheck HSDPA and in SMS choose 'GSM'
(all is translated from Dutch, hope i used the right words)
Thanks Nirak.
One of my settings was wrong - I should have known that from last time, but my brain's elsewhere at the moment!
Must have upset it when I flashed
Cheers for now.
phil-w said:
Hi and thanks for replies so far...
I have just done a hard reset to make sure I haven't loaded anything that may mess up the wifi connection... Even when wifi is on and I am connected to a wifi access point OK it still uses gprs/3g not wifi..
Back to the "drawing board" I think...
Any more ideas please...
Phil-w
Click to expand...
Click to collapse
Phil, can't you simply switch the "Data Connection" on/off switch to 'off' ?
I have it in the Comm Manager right at the bottom. The Wi-Fi and Phone could be left 'on'. I can't try if it works because I only use the phone on 2G.
Joe
jfranek said:
Phil, can't you simply switch the "Data Connection" on/off switch to 'off' ? I have it in the Comm Manager right at the bottom. The Wi-Fi and Phone could be left 'on'. Joe
Click to expand...
Click to collapse
That's how it should work actually. Either one, Wi-Fi or 3g/GPRS. But what phil is saying is that it also activates data connection (3G/GPRS) even when wi-fi is connected.
On my set, and in my network (not Orange but standard GSM).. this is how it works :
The moment I invoke any application that requires internet connection (weather update, activesync, opera, etc) Jade invokes data connection first (3G, GPRS, etc). Unless if I invoke Wi-Fi connection on first, then data connection is ignored, it will stay off.
So what I normally do is, whenever I want to use internet, I connect using wi-fi then browse the internet. If there is no available AP, then I turn off wi-fi and continue browsing , which is then connected using 3G/GPRS/EDGE?HSDPA
azahidi said:
(...) The moment I invoke any application that requires internet connection (weather update, activesync, opera, etc) Jade invokes data connection first (3G, GPRS, etc). Unless if I invoke Wi-Fi connection on first, then data connection is ignored, it will stay off.
So what I normally do is, whenever I want to use internet, I connect using wi-fi then browse the internet. If there is no available AP, then I turn off wi-fi and continue browsing , which is then connected using 3G/GPRS/EDGE?HSDPA
Click to expand...
Click to collapse
This is the way it normally works and should work under WindowsMobile. The Orange-ROM seems to be "manipulated" by the provider (?) not to work in this desirable way. All (or some?) Orange-ROM-Handsets seem to activate the data connection (3G/GPRS) every time ignoring the established Wi-Fi-connection. This rises the providers business volume.
It would appear to be correct about orange having had the method of connection changed.
I have just found and installed a different RADIO.ROM to my Orange Touch 3G and now it appears to connect as required.
Still not 100pc happy but will post my observations later with the rom numbers if it helps anyone else out..
Phil-w
Look on the HTC JADE reflashing on this site
Hi All,
There is no way around the Orange apps to enable WiFi, but I successfully reflashed the Roms in my Orange touch 3g yesterday.
Have a look here for the details on what to do:
http://forum.xda-developers.com/showthread.php?t=514406
Follow the instructions carefully, and I chose to install the Stock HTC ROM 1.40.721.2 from the ROM post.
Wifi is then free....
)
Well I appear to have got around the Orange Unique problem.
I upgraded the Rom on my Orange UK Touch 3G to the Jademan SuperRom V3. That got rid of the Unique side of things but with no improvement with Wifi connectivity.
The connectivity problem with wifi still caused problems, the internet connection would NOT use wifi even if I disabled the GPRS / 3G data connection with "NoData" It just returned a message saying it had failed to connect.
I decided to find a new radio rom image which I managed to on this Jade forum. I flashed the new rom and tested the same connections again. This time the wifi connected via Wifi first and without any problem... It would appear that flashing the Jademan rom didn't update the radio as well, I needed to update the radio as well.
The clue may be in the radio rom version number,
Original orange 0.29.30.U23
New Radio rom 0.41.30.12
A assume that the U in the orange rom refers to "Unique", which now I have replaced it, it appears to have cured the wifi problem and it is working just as any other Non-Orange Jade / Touch 3G does....
I have not noticed any problems with any other radio related issues since the upgrade, GPS, 3G/GPRS etc all seem to be fine.
I do find that the phone does struggle to connect with some Dlink AP's though... It may be a problem with the Dlink more than the phone but I still need to do more tests on that.
May be that will help a few other people out there...
Phil-w
Hi Phil,
I had exactly the same problem!
Started with an unlocked HTC Touch 3G with Orange customised ROM and then replaced it with the SuperROM. WiFi was unusable so (having read your post) I re-flashed with the standard ROM released from HTC and then re-flashed the SuperROM. This gave me the same Radio ROM that you show above however the WiFi problems seemed to be no better.
While I liked the idea of having the SuperROM I have gone back to the latest standard HTC ROM and all seems to be well.
John
Hi John,
My wifi now seems fine except not liking Dlink AP's for some reason.
I don't even need to stop gprs data with NoData etc, if there is a wifi connection available that I have setup previously it will use that rather than GPRS..
I appear to have "de-Oranged" it !!!
What probs do you still have on your Touch 3G ??
Phil

setting connection preference ???

is there a way to make sure the phone only connects to my home wi fi hub when at home and does not connect via my 3g vodafone connection. I want it to automatically select the fastest link and not waste my 3g allowance ? I've searched but cannot find a solution, thanks
+1 good idea, anyone got anything on this?
Andi,
The solution I would use would be to go to Settings>Wireless Controls and simply switch Data Connections off, Wifi On when at home.
You would have to remember to to reverse this when done if you want to access 3G services.
WB
u could use G-Profile.. It allows you to set up different profiles and switch them automatically based on your current cell id. Wifi on/3G off when at home, other way around when not. Works like a charm for me
thanks for the tip but when I do that it then automatically turns it back on even when I'm connected to the wireless hub, all of a sudden they both are on . . . . . . .?? any ideas ??
i have the same problem... it keeps using my 3G/EDGE network even if WIFI is available... and i dont get it how can HTC afford not to give us an option to set that the phone asks you for permission when connecting to 3G/EDGE network... this **** costs and im not really happy about the fact that my phone can connect to a network whenever it feels like.
(and yes this **** keeps happening even tho i disabled automatic updates in weather/time applications.)
In BSB tweaks if you press options I think there is an option to disable all data connections. I have never tried it but maybe it will override all connection attempt? Give it a try. Also, I flashed to the 2.01 ROM and I think the data connections are a little less persistent, though I don't wan't to guarantee anything!
andi1977dog said:
is there a way to make sure the phone only connects to my home wi fi hub when at home and does not connect via my 3g vodafone connection. I want it to automatically select the fastest link and not waste my 3g allowance ? I've searched but cannot find a solution, thanks
Click to expand...
Click to collapse
does it not do that by default? i cant send emails through t-email when i'm at home - I just presumed this was because i was connected through my wireless router. turning off wifi allows me to send emails.
thus I presumed wifi takes preference?
I am wondering the same thing. The idealist situation would be to have both connections active at the same time, and let the HD2 make sure that wifi is used when the connection is there. Is there some kind of application to verify which connection is being used?
Great thread - I am not the only HD2 owner who is annoyed with the problem with the HD2 switching on its GRPS data connection without my approval!!!
Could it be that the HD2 turns off the wifi when it goes to sleep and then tries to connect to the web using the GPRS network? In that case how do I prevent turning off WIFI when in sleepmode?
I read somewhere else in this forum about a G-profile. Being a newbie with HTC I have no idea what this is. Any clue?
But overall: Yes, it would be great if HTC added an option to set network connection preferences.
WiFi does take preference if it's connected! Dont forget when you are at home and you turn your phone on from standby it will take 10sec or so to connect to your WiFi router, if you try and use IE, Opera, Twitter, Weather Update, Email, etc... before it's connected it will fire up your 3G data connection!
The phone does not how ever turn off your data conn when it's idle which is annoying! You need to use Bandswitch or CommManager from here http://www.commmgrpro.com/jsp/main_frame.jsf;jsessionid=103F335931311F019BD540B82E479383 or WMLonglife from this forum (do a search).
there must be someone out there with ghe know how and expertise to solve this ?? glad to see its an issue for othet folk, i like the idea for selecting wi fi over gprs if its there to be selected.......
I found out that my HD2 automatically closes the 3G connection when I have wifi active. I'm not sure why it does that, I know pretty sure that it had not always done that. But I'm quite happy with it
It turns 3G on again after disconnecting from WIFI, which is what I want.
so if you tap the notifications tab and the "contratc internet" is counting and the wi fii is connected it is using the wifi and not the "contract internet" even though the timer is counting ???
Can anyone confirm ???
p.s tried using the G-Profile software, it seems very inconsistant and didnt always turn off what it should when you select the profile so im going to unistall it.
for some reason the automatic internet settings from vodafone messes up/hides the "The Internet" or "MyISP" connection that is in the phone originally.. I even hard resetted but you just can't seem to stop the automatic settings..
disable the proxy of the "Vodafone live!" connection and it will work.. just like twitter etc..
the same with email only checking through 3G and not wifi.. but set the server settings of your account to "The Internet" after you disabled the proxy.. (advanced settings at the smpt server tab)
hope this helps.. but a thing worries me, as I don't know anything about proxies, why does vodafone specify a proxy if we don't realy need one.. to port us over their live portal or something? (on my old sony ericsson the track ID service didn't work because of that)
"disable the proxy of the "Vodafone live!" connection and it will work.. just like twitter etc.."
thanks but how do i do this ??
anyone know how i do this ? thanks
After including the Taskmanager as a quick link in HTC Sense I am now able to close all programs. Now I do no longer experience any unfortunate GPRS connections when connected to WIFI.
Only problem is that when running on batteries the WIFI connection is closed down when the unit enters sleepmode. However during sleepmode, if I have not closed down programs accessing the web these are now able to connect to the web by using the GPRS connection.
Why on Earth has HTS decided to decipher a click on the X as MINIMIZE and not CLOSE!!!
tnyborg said:
After including the Taskmanager as a quick link in HTC Sense I am now able to close all programs. Now I do no longer experience any unfortunate GPRS connections when connected to WIFI.
Only problem is that when running on batteries the WIFI connection is closed down when the unit enters sleepmode. However during sleepmode, if I have not closed down programs accessing the web these are now able to connect to the web by using the GPRS connection.
Why on Earth has HTS decided to decipher a click on the X as MINIMIZE and not CLOSE!!!
Click to expand...
Click to collapse
I believe my Wifi connection is kept alive, even in sleepmode.
Josan123 said:
I believe my Wifi connection is kept alive, even in sleepmode.
Click to expand...
Click to collapse
Sorry, forgot to mention this - but in order to save battery power I have asked the unit to close down the WIFI when in sleepmode (using BsB Tweaks). And indeed it gives me more battery life.

Categories

Resources