Hi guys, I just put in a 1GB Micro SD card and I am having problem getting the card out or ejecting the card. Anybody know how or what is the correct way to get it out. I try pushing the card down but it doesn't pop up.....please help thanks!!!
Just press it inwards, and will pop out itself
I had the same problem. I went back to the store and we tried to get out by pushing it, but i did not work. We manged to get it out by pulling it out, and then we inserted a dummy card. This made the eject mechanism function again, and when I inserted my card again it worked.
I had the same problem when I first put in my micro SD card. I had to pry it out with tweezers. Thanks to this thread, I got the idea that I could get the mechanism working. So, I worked the card in and out several times, pushing it all the way in with my nail and letting it snap back a bit (and prying it out again) until the mechanism became loose enough to work properly.
Related
Hey everyone, does anyone know why my xda can access and format my 1gb sd card, but suddenly my pc cant write to the card becuase its "Write Protected", even tho the slider is not set to lock.
Anyone have some ideas ?
Hi,
I just had exactly the same problem with a 512Mb SD Card. My card reader doesn't seem to recognize the slider properly, in the end I taped a small piece of tape over the length of the indent on the card and it started working fine on the PC, took the tape off and put it back in my XDA IIi and eveything was fine. Saved me an hour installing TTN5, took me an hour to figure it out!!!
HTH
Wizard
hi!!
i need some help with my mda compact..
i bought a new sd 2Gb card and it wont read it...
its asks to format it and does but nothing else...
thats it..
it cant read it..
I've had the same prob with an 2Gb MMC, and i fix it by unscreawing a bit the top 2 screws of the mainboard (have to open the upper back part). The ideea is to push the card slot backword, until it reads the card correctly, anddoing this with the battery cover on place, to be able to power on your device after uncreawing a bit, to test the rezult. By doing this I fixt also some reading problemsa that i had with other card (when paying movies from the card, it would freez the move until I would pull out the card and put it back again). Hope to be of help.
Hi all,
I just got recently a 2gb microSD from Sandisk and conected in my X01HT(HTC TyTN), it doesn´t reconize the card and the card get very, very hot
anyone could help me with that?
Thanks
Assuming there's nothing wrong with the card, you might have put the card in wrong, or the card might not be aligned properly when placed into the slot. Try these:
1) make sure the contacts side is facing up when you put in the card (slot facing you, pda screen facing up)
2) as you insert the card (slowly), try to align it more to the bottom left of the slot. If it's inserted correctly, you should feel some springing pushing the card out as you insert it.
3) If the card is inserted correctly, it should bounce back out if you push it in a little.
hopefully that helps, but if all else fails, take the card back to the store.
Hi. I broke one of the 2 "arms" that make contact when the card is pressed down so my wizard is not recognizing it.
Is there a way to fix this? when i press the card down, it stays there but the backlight doesnt turn on and the card is not recognized.
Thank you
Also, the broken arm is broken in half
Ok, i figured it out myself.. I wrapped the sd card with aluminum foil (leaving the reading area uncovered) and thats it. My wizard is reading the sd card again.
V20 H918 10j (still on Nougat)
Here's when it happened:
We were going on a road trip so I shut the phone off, took out the SD card (64 gig Sandisk), then the sim card, put the SD card back in and closed up the phone. I did not turn the phone back on. Then put the sim card in my tablet so it would have data. That worked fine.
The next day, I want the sim card back in my phone, so I do the reverse. Boot up the phone and it does not see the SD card at all. I put the SD card in the tablet and the tablet sees it just fine. Back in the phone - no go. I try a couple reboots and nothing. Boot to TWRP, it doesn't see it.
I get home and dirty flash the rom (Ovrdrive). Still doesn't see the card. I try a couple other cards (32 and 64 gig sandisk) which work just fine in other devices and the computer and the phone either doesn't see the cards or it says they are corrupt. So I format a 32 gig card (I did it a couple times in both xfat and fat32), put it in the phone and the phone says it is corrupt and needs to be formatted. So I select format. The format box is immediately at 20% and then it crashes.
I tried using ES File Explorer on the phone to format it but still a no go. I re-flashed the kernel that I have been using for the last year, that didn't help either. I used contact cleaner spray and then even used a soft small paint brush to try and clean the contacts. Nothing.
I had not put any new apps or made any changes to the phone in over a month before this happened. So.... I think somehow the pins for the card somehow got damaged or just old and something just got bent or broken or tweeked. I have another V20 that got water damaged and I looked closely at the SD card pins and compared to the current phone. I can't see any difference.
I'm posting this in case anyone else has had this problem and 1. was able to resolve it or 2. replaced the sim reader and that fixed it. Sim readers on ebay are cheap, but they have to be soldered in. Something that small is beyond my skill level.
There is a thread for the G6 that talks about this same problem. No solution. Speculation about having the card reader replaced. One person did a complete factory reset twice and that didn't work. So I'm left to believe this is a hardware issue.
Cheers.