Related
After a week since I've upgraded from 1.66 to 1.72, my Qtek2020 is dead
I was playin with XBox and my Qtek was chargin on cradle
after a while It reset one,two,three,four times !!!
I put It out from Cradle but It continue to reset continuosly
I try to reset, hard reset, nothin to do
After 2-3 minutes It turns on magically...It seems ok, but while
It was Restoring Backup Data It restart to Reset Continuosly, but now
It is DEAD
Soft reset, Hard Reset, Power+SoftReset+Joystick button....
all is dead
any suggestion before I go to repair It ?
damn
Qteknology
Have you removed battery. :?: What color light if any is illuminated when in charger. Also check the switch that locks the battery into place at base of battery.
U already know my problem, cruisin u're great
My battery charge was RED :?
I changed battery and Cradle at shop were I bought it last week,
now it's all OK
but, how hell it depends ? battery sucks ? or something else ?
It LIVES AGAIN
Batteries do fail sometimes, most modern batteries have a chip onboard and this sometimes burns out too. Just bad luck I think.
but how do u know about Red Colour of Charge ?
Have u some experience about it ? Have u read somewhere ?
I have upgraded my Qtek 9100 with new Windows Mobile 6 WWE. After restarting the device everything worked OK, i just setted up basic things (clocks, owner information etc..) - nothing peremptory. After this I restarted it with soft reset again and it still worked... But then i shortly pressed power button (just to turn off the display) and after 10 minutes i wanted to turn it on again, but nothing happened.. The GSM LED diode still winked, but I couldnt turn the device on. So I used soft reset and again nothing happened, just GSM LED diode stopped winking. - Since this it was totaly bricked. I also tryed hard reset and bootloader mode, but none of this appered. The battery was 100% charged and I tryed to charge it again, but it didnt helped. I also tryed to take out and insert again the battery, but it still was unsuccessful What should I do now?
If the lights are still blinking then the phone still has life and appears to be operating (in some fashion). If you plug in the USB cable, does the charging light come on? If that does, then it is definetly still running.
I would suggest you taking the battery out and leaving it out for 5mins - 30mins. Then putting it back in and try turning it on. If nothing, try doing a hard reset after that. Also remove your SD card.
Good luck
Lights arent blinking at all. When I plug in the USB cable or charger, also no lights. I also tryed hard reset after plugging the battery, but again unsuccessful
Sorry, but its sure sounding like a bricked phone (although I've never heard of one that bricked sometime later. Usually its right after an upgrade).
Only other possibility is your battery has been completely drained. Can you get another battery to try in the phone? If not, then you can try jump starting the battery.
http://forum.xda-developers.com/show...38&postcount=9
Yes, I know that is bricked. What should I do to unbrick it?
Temporary brick at most if it was still running after the update. Try the different combos of battery out and in. This sounds like what a device does when the battery is bombed. If nothing, a new battery is definitely in order before you assign it permanent doorstop status. Good luck.
I have problem with my mda pro its seems to be dead.
After upgrade that stoped on 99% with error message 115 i can do noting anymore. No bootloader,hardreset etc. No more charging the device ( no orange light ) but when i out the battery the red light is on but when i put back the battery its again no light on it.
Waiting for a new battery now but i don't think that is the problem
...if some one help me please replay Thanx
My friend is having the same problem
Any solution yet?
Thank you.
seems to me, this is a battery
Sorry!!
tabasco said:
seems to me, this is a battery
Click to expand...
Click to collapse
I have the same problem,,,Isn't the battery.....Your uni is death, If you can't enter to Bootloader your uni is death, If you conect the uni to charger adapter and press reset you'll see a red blink light in status led, this means empty rom, ok? In same way I did brick my jasjar too...for a moment no fix yet.
AIN1 said:
I have the same problem,,,Isn't the battery.....Your uni is death, If you can't enter to Bootloader your uni is death, If you conect the uni to charger adapter and press reset you'll see a red blink light in status led, this means empty rom, ok? In same way I did brick my jasjar too...for a moment no fix yet.
Click to expand...
Click to collapse
Thats exactly. My friends gets a red blink for a few seconds after connecting to charger. So it's the unit thats dead I bet.
What about JTAG method?!
we are working on it for wizard
I have the same problem, but I had no problems during the last flash. It was fine on Friday. I don't look at it until Monday and now its dead exactly as he described.
No light when plugged into charger.
Red light when battery out plugged into charger.
If I press reset with battery and charger in, I get a single quick blink of the red light.
Has my bootloader some how randomly corrupted?
that's is it
DHarman said:
I have the same problem, but I had no problems during the last flash. It was fine on Friday. I don't look at it until Monday and now its dead exactly as he described.
No light when plugged into charger.
Red light when battery out plugged into charger.
If I press reset with battery and charger in, I get a single quick blink of the red light.
Has my bootloader some how randomly corrupted?
Click to expand...
Click to collapse
In simply way: If you can't enter in bootloader mode, say: "Rest in peace my little Universal" When you have an error after the upgrade finish "DON'T RESET THE DEVICE"... I know! I know!!! after the fail upgrade the display say's hard reset or soft reset to your uni, its wrong!!! Just disconect and conect again the usb and begin the update again until windows recognize it. or use "Exit Bootloader.exe" but We fall in same error, sorry no fix yet, The JTAG metod was derelict, hopelest smart cientist worked hard but can't do it.
AIN1 said:
In simply way: If you can't enter in bootloader mode, say: "Rest in peace my little Universal" When you have an error after the upgrade finish "DON'T RESET THE DEVICE"... I know! I know!!! after the fail upgrade the display say's hard reset or soft reset to your uni, its wrong!!! Just disconect and conect again the usb and begin the update again until windows recognize it. or use "Exit Bootloader.exe" but We fall in same error, sorry no fix yet, The JTAG metod was derelict, hopelest smart cientist worked hard but can't do it.
Click to expand...
Click to collapse
I can still get that hard reset menu up (both soft keys + reset) where it says 0 to reset device, 'x' to exit. The reset doesn't work though, and haven't tried to reflash yet. Am I going to be able to?
you don`t unideath
use the mtty metod to save tour uni (task28 55aa) and load again the prefered ROM........Do you can enter to Bootloader, or not?...
Hello Guys,
Let me understand, if i can't enter into bootloader mode it means i lost my xda exec? :-(
None of the options, hard reset, soft reset work, only the red light blinks sometimes.
i also have this problem. its suddenly dead. the signs are the same.
i was using it fine.. left it to charge next morning its dead.
i cant enter bootloader mode too.
Hi,
a friend showed me his broken Magician (T-Mobile MDA Compact).
It did not turn on, no led, no nothing...
I plugged in my fully charged battery from my Charmer and connected it to my power supply, same thing.
I tried to enter boot loader (power, camera, reset pin), no reaction.
Any hope for this thing? Is there a sort of even "harder" reset?
Your phone may have 'bent' or broken battery terminas that aren't making contact.
Hi,
sorry I know this doesn't answer your question at all, but I was just wondering if you managed to get your Magician fixed in the end.
My daughter's SPV M500 recently stopped working, pretty much the same symptom, so I was wondering if you were successful in fixing it, and if so, how?
Thanks in advance!
Try this- open the back of the device, undo all the screws, open until you see the circuitboard. on one side (i can't remember which one) check the widest cable that connects to the circuitboard - undo the latch and pull it out, push it back in and close the latch, then try turning it on. that cable keeps coming out in mine.
The widest ribbon, is actually the LCD ribbon.
He would have still heard the introductory 'beep' if the unit was actually working (even if the LCD wasn't connected).
i got the same problem.....
i am surfing on the net of my XDA when it shutdown i thought it was a battery problem so i try to charged it but i've noticed that it didn't opened for a couple of hours of charging. i tried to reset but it didn't work. so i decide to hard reset my phone but again it did'nt work, and now my XDA II mini WM 6.1 is totally dead.... i also tried to flash my phone but the activesync of my phone cant detect my PC, and even rebooting my phone also did'nt work.
i've also noticed the redlight blink on the led for a seconds when i charged and unplug the charger...
Hello.
I have big problem with my Uni. It's not booting, it's not going to bootloader mode. When I connect Uni to computer the red LED blinks and nothing happen. Battery works in other uni.
hmm leave the uni on the charger with battery in.
also have you tried using another battery in the dead uni?
same problem
I have the same problem during upgrading to wm6.5 computer gave me an error message
i pressed the reset button and the unit went blank
now its dead whatever i do notthing happens bootloader keys , hardrest keys , reset buttons nothing happens
if i connect to the wall charger to the unit nothing happens
if i press reset button red light blink once and if i remove the battery and connect the pda with the charger red light remains on
please help
I connected the unit with charger for whole night hoping it will work but nothing happened even the battery is cold ?
holy **** me too. i borked my sd slot so i took it apart, just popped off the back and fiddled with the sdpins and now it refuses to boot+redlight.
any thoughts? i miss my phone -_-
Hi
I noticed if i connect the device with my pc the red light flushes time to time and the pc gives the error of usb device not recognized please help I miss my o2 exec.
many thanks
keyfetcher said:
Hi
I noticed if i connect the device with my pc the red light flushes time to time and the pc gives the error of usb device not recognized please help I miss my o2 exec.
many thanks
Click to expand...
Click to collapse
did you try another battery in your uni? also did you try tapeing the pin on the battery that reads the voltage level?
according to the universal service manaul flowchart, a redlight indicated bad battery>bad battery pins>shot motherboard.
so i don't think this is good. anyone got any..thoughts on figuring out WHAT exactly happened?
Hi
thanks for the input
will you please guide how I can tape the pin on the battery that reads the voltage level
many thanks
help
I have upgraded my xda exec from wm5 to wm6.1 but later decided to upgrade by downloading this upgrade from xda developer site " BA_6.5.23004.WWE-xplode-R7.1"
during upgrading it reached to 75% and then my pc gave me an error message
unfortunately i continued and later on a gray screen appeared on the xda exec
i pressed the reset button and the unit went blank
now its dead whatever i do nothing happens bootloader keys , hard rest keys , reset buttons nothing happens
if i connect to the wall charger to the unit nothing happens
if i press reset button red light blink once and if i remove the battery and connect the pda with the charger red light remains on
I connected the unit with charger for whole night hoping it will work but nothing happened even the battery is cold ?
I asked my friend to check the power in battery and he said its charged
I dont know what is wrong ?
please help
keyfetcher said:
I have upgraded my xda exec from wm5 to wm6.1 but later decided to upgrade by downloading this upgrade from xda developer site " BA_6.5.23004.WWE-xplode-R7.1"
during upgrading it reached to 75% and then my pc gave me an error message
unfortunately i continued and later on a gray screen appeared on the xda exec
i pressed the reset button and the unit went blank
now its dead whatever i do nothing happens bootloader keys , hard rest keys , reset buttons nothing happens
if i connect to the wall charger to the unit nothing happens
if i press reset button red light blink once and if i remove the battery and connect the pda with the charger red light remains on
I connected the unit with charger for whole night hoping it will work but nothing happened even the battery is cold ?
I asked my friend to check the power in battery and he said its charged
I dont know what is wrong ?
please help
Click to expand...
Click to collapse
I beleive that BA_6.5.23004.WWE-xplode-R7.1 mean blue angel rom. http://forum.xda-developers.com/archive/index.php/t-482997.html
so you are pretty much out of luck unless you can jtag.
again the same problem
keyfetcher said:
I have the same problem during upgrading to wm6.5 computer gave me an error message
i pressed the reset button and the unit went blank
now its dead whatever i do notthing happens bootloader keys , hardrest keys , reset buttons nothing happens
if i connect to the wall charger to the unit nothing happens
if i press reset button red light blink once and if i remove the battery and connect the pda with the charger red light remains on
please help
I connected the unit with charger for whole night hoping it will work but nothing happened even the battery is cold ?
Click to expand...
Click to collapse
...almost the same.
my problem occurred after I did a soft reset. It took it a while to boot and every other time I used soft reset the boot took longer and longer until it did not want to turn on again.
Soft reset doesn't work but when it's left on the charger and pressed, the battery light blinks once. It won't charge and my PC registers a device malfunction when connected through USB.
The only sign of life pops up when I press hard reset but after I press 0 or X nothing happens.
Please help!
I have same problem as well, I even bought spare battery but uni remains dead and silent.
Beside the fact that when it's connected to PC, windows show unrecognized usb device.
what happened before it died? did you ... do anything to it? mines still dead as a doornail.
I am not alone :'(
It means many other fellows are suffering from same.
strange , total silence from experienced guys... atleast they can say it is useless for you to try.. and now dig a grave for it.
Experienced guys have their own lives too
Wait with patience till someone replies you and do not double post on same topic please