I flashed my x96max plus I think with wrong rom
Then it stop doing anything even the display or power, when I connect it to amlogic USB burning tool it can't recognize but after about 10 minutes it begins to recognize
I tried several versions of rom ,but not work
Could anyone help me with the right version of this bad device & what's the suitable version of burning tool
I attached pictures of all chips of the device
Related
Guide fix "device not found in dload trying flash programmer" when use boardiag .
Lg g3 qualcomm 9008 when install driver then use tool boardiag fake tool say device not found in dload trying flash programmer
when you use tool fake board share in xda another tool say device not found in dload trying flash programmer you need remove battery (of lg g2 hold power 1 minute) then connect cable again and use tool again
Sure install driver 100% wrong
With windowns 64 bit you need restart pc then click f8 choose disbable driver singturne....
Then remove battery (hold power 1 minute with lg g2) then connect cable try use tool unbrick >> sure done 100%
I will updload video error dload
Remember disbbale tool sony erricson if you have open tool in taskbar
then read topic use tool of my unbrick
http://forum.xda-developers.com/lg-...lcomm-9008-t3072091/post59881075#post59881075
i have same problem when i hit start button show that error ( b2bsuppportlg device was not found in dload trying flash programmer )
i tried on 4 different pcs (win7 .. win xp service pack 3 .. ) but same result any one have solution ???
driver signature check disabled?
drivers correctly installed? (lg AND qcom)
edit unfortunately, the tootls provided here on xda are mostly broken or missing important files...
this seems to be due people not wanting other people (support-shops) beeing fired
weird weird stuff tho
everything fine but still same error u have working link ??
hey there guys, somebody has resolve this problem? im suffering the same problem in a nexus 5
im also facing the same prob
all are dumb
No one want helping others they only want donations from us so guys carry on if u dont want to help us then no worry
Hi All! I've found a solution!
The trick is to use a Heat Gun for heating up both ICs on both sides of motherboard.
I've had the same problem:
"device not found in dload trying flash programmer" when use boarddiag​I also tried SRKtool, but in last step, I couldn't find the partition.
So both SRKtool and BoardDiag failed.
All hope was lost. So I did warm the CPU and Storage IC on both sides with Heat gun!
about a minute or so for both ICs until both were very hot.
That did the magic.
After that both SRKtool and BoardDiag worked for me perfectly and I was able to revive my phone.
I think in all our cases this problem is because storage IC and CPU IC have been out of work for a long time and they need to get warm to work after all this time of being turned off.
Really hope this works for you all.
Reposting it here, since this is the Lenovo sub-forums. Probably may find more help here.
I was using the Allegro ROM for the A1000G and it was running fine and dandy without any problems. Last night I tried installing a game and after I restarted it, it didn't turn on. I thought that maybe the device had low battery or something. So I plugged it in and let it charge for an hour and it still didn't turn on. Than I let it charge overnight and in the morning, it still doesn't turn on. So I tried to flash the Stock ROM for Lenovo a1000g and I got an error saying the storage was different or something - Error 3182 Message: BROM ERROR: S_STORAGE_NOT_MATCH (3182) [Edit - Tried to find the error, this is the one]
It was probably because the Allegro ROM was installed before it stopped working. So after that failed attempt at Flashing the Stock ROM - I don't get the battery indicator anymore and no matter what I try inside SP Flash Tool, it doesn't detect the device and the flashing process doesn't work. I tried installing and uninstalling all the MTK and Mediatek drivers but still not working. It shows up as MediaTek DA USB VCOM (Android) but it doesn't disappear, unless I remove the usb cable.
Before when I flashed the Allegro ROM and as seen across other youtube tutorials and guide, the device would show up for 2-4 seconds before disappearing and the SP Flash Tool would start working. Now it is just blank and the MediaTek DA USB VCOM (Android) doesn't go, no matter what.
Please, I would appreciate help. Since I don't have much knowledge regarding this. What must I do? I am depending on you guys.
~Aaron.
Bump. Please someone help.
__PUMA__ said:
Bump. Please someone help.
Click to expand...
Click to collapse
Thread closed as duplicate. I have left this one open
https://forum.xda-developers.com/th...p-lenovo-a1000-g-indian-version-hard-t3630644
but closed the others. Please do not make any more duplicates
Sawdoctor
Reposting it here, since this is the Lenovo sub-forums. Probably may find more help here.
I was using the Allegro ROM for the A1000G and it was running fine and dandy without any problems. Last night I tried installing a game and after I restarted it, it didn't turn on. I thought that maybe the device had low battery or something. So I plugged it in and let it charge for an hour and it still didn't turn on. Than I let it charge overnight and in the morning, it still doesn't turn on. So I tried to flash the Stock ROM for Lenovo a1000g and I got an error saying the storage was different or something - Error 3182 Message: BROM ERROR: S_STORAGE_NOT_MATCH (3182) [Edit - Tried to find the error, this is the one]
It was probably because the Allegro ROM was installed before it stopped working. So after that failed attempt at Flashing the Stock ROM - I don't get the battery indicator anymore and no matter what I try inside SP Flash Tool, it doesn't detect the device and the flashing process doesn't work. I tried installing and uninstalling all the MTK and Mediatek drivers but still not working. It shows up as MediaTek DA USB VCOM (Android) but it doesn't disappear, unless I remove the usb cable.
Before when I flashed the Allegro ROM and as seen across other youtube tutorials and guide, the device would show up for 2-4 seconds before disappearing and the SP Flash Tool would start working. Now it is just blank and the MediaTek DA USB VCOM (Android) doesn't go, no matter what.
Please, I would appreciate help. Since I don't have much knowledge regarding this. What must I do? I am depending on you guys.
~Aaron.
Bump. Please someone help.
Hi,
I'm not sure I'm posting in the right section but, I had a really bad experience upgrading to android 10. Really sluggish and slow... so I tried to downgrade to android 9 by using Lenovo's Rescue and Smart Assistant.
What I did, is to find the stock ROM for my model, and replace the files downloaded by the Rescue Assistant (which downloaded the latest firmware). The process went through, but now the device wont power on.
When I plug in the USB, windows makes a sound, the charging light comes on, but The rescue Assistant nor SP flash tool is able to flash the latest firmware.
Is it bricked for good?
Model : TB-XF606F
Hardware number : 60
Maybe your computer doesn't recognize your tablet. Did you ever try using sp flash tool with your tablet before? You can try reinstall or install a driver for your table if you haven't done it yet.
Well the tablet is recognized as the "mtk vcom..." in device manager. I guess it is the driver that the lenovo rescue app installed.
I have never used sp flash tool with my tablet, just the lenovo rescue.
I tried on 2 different pc and it is the same thing. I think the problem is that I can't turn off the tablet properly, even though, all I can see is a black screen.
I will try to drain the battery by keeping the power button pressed with some scotch tape. I don't know what I can do else.
Edit: I tried a few other times with flash tool using different setting for the connection (with battery and full speed) and nothnig happened. But now windows says it does not recognize my tablet.
did the same thing exactly. . bricked lenovo m10 fhd plus x600v after i flashed a downgrade version. dont try to downgrade this thing. i had already flashed it with 3 or 4 versions the same way , but when i chose to flash the oldest version available with the model , this tab got completly unresponsive , no feedback when try to boot into recovery, fastboot, or system . neither does it gets recognised in windows or anything - device manager dowsnt recognise this usb device ( in device manager properties comments it reads- USB\DEVICE_DESCRIPTOR_FAILURE). if you find a way to reflash the device please let us know. good luck .
Bricked mine after being completely running smoothly on Lineage, then was messing around trying to get gapps installed and jacked up the partitions. TWRP said no OS. Kept messing around and mistakenly locked the bootloader again with apparently an unverified boot partition. . I couldn't get SP Flash tool to work ever either. Pretty sure it's a door stop now.
Hi Folks,
I'm having RK3288 Board it was working fine until I decided to do an OS upgrade. Accidentally ROM didn't install correctly and now the device is nearly bricked.
I'm searching the web for the past 2 months to try any method which can help me to return the board to a working state.
The issue I tried to Install a new untested ROM over a working ROM and the device isn't booting UP, whenever I'm trying to boot nothing happens also RK Android Tool isn't able to detect the device. The issue is pretty big as I'm left with more than 20 unused boards.
Could you please suggest how to enter eMMC or EDL mode? Attaching a Snap of my Board.
HI ,
you can short the Pins 7/8 , right side , count from triangle in IMG .....402.jpg , for more Infos search on Freaktab ,
greetings / gefattern
Hi,
i have a similar Problem with a rk3288 based Chip.
I tried to do a firmware update, but it ends with an error. Now the RKDevTool only shows "No Devices found".
Can anybody give me a hint, how to solve this? The board seems to be powered, because the Power LED lights green.
Please look a the photo attached
thank you very much
A128/A139 said:
Hi,
i have a similar Problem with a rk3288 based Chip.
I tried to do a firmware update, but it ends with an error. Now the RKDevTool only shows "No Devices found".
Can anybody give me a hint, how to solve this? The board seems to be powered, because the Power LED lights green.
Please look a the photo attached
thank you very much
Click to expand...
Click to collapse
Please share pic from the back of the port also. don't attach PDF file make it JPG
dbzdivik said:
Please share pic from the back of the port also. don't attach PDF file make it JPG
Click to expand...
Click to collapse
Hi,
here are the pics. Many thanks
Has nobody any idea?