I installed TWRP on my tablet two months ago, and after it finished loading Odin3, the computer showed success, but the tablet could not be turned on. I tried to rerun a month later and got stuck. I unplugged the cable and I saw the"An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC software"error, and a line in red that said "VOLTAGE Level [2599]". I use Smart Switch's emergency recovery, but it doesn't detect my device. Does anyone have a way?
Wonwon73607 said:
I installed TWRP on my tablet two months ago, and after it finished loading Odin3, the computer showed success, but the tablet could not be turned on. I tried to rerun a month later and got stuck. I unplugged the cable and I saw the"An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC software"error, and a line in red that said "VOLTAGE Level [2599]". I use Smart Switch's emergency recovery, but it doesn't detect my device. Does anyone have a way?
Click to expand...
Click to collapse
im have the same freakin problem its bee moth i havent found any answers
Related
Hello all,
I have big problems with my L7 P700.
I rooted it two month ago, even that time I was stuck at yellow emergency mode, but using some instruction (disable LG modem) I was able to boot phone again.
Today I believe I have totally different problem.
What I did, I found stock firmware 4.1.2 and LG drivers, I installed it. Restarted phone and pressed Volume UP + Power. Phone went to yellow emergency mode, ok... Then I tried to use KDZ_FW_EN, phone was not seen. I restarted it and it booted ok to system. Turned of again, went to emergency mode than I opened KDZ_FW_EN again. I tried to read phone information, the program chrashed. I opened it again and tried to flash firmware. There were errors, and I am pretty sure phone wasn't even properly connected to PC!
So if you don't understand me I will repeat again.
I went to emergency mode WITHOUT USB DEBUGGING ON (I disabled it one day, I remember, this time I forget to turn it on). So Under device manager I see only USB composite device and LG Modem, disabling modem isn't a fix (like two month ago when I rooted). This time I can't use any of flashing tools cos I am not in debugging mode =(. The only thing I don't understand is how I was able to destroy my phone if it wasn't even flashing it (port number was -1, some wparam 100-1000 errors, i closed program in the middle but it wasn flashing if I wasn't in debug mode?)
Phone is rooted and stuck at emergency mode, without usb debugging and hard reset bring the emergency on (BOTH VOLUME BUTTONS + MENU)
Anyone?
Yes, I had the same problem a few months ago. Try install firmware stock V20D without battery and then connect phone via cable USB to PC but turning on Emergency Mode. Next, 3GQCT and CS EMERGENCY. Of course you can change port USB. Try reinstall KDZ and drivers. If you have Windows Vista then that's the problem. I'm sure that this situation will be resolve.
Ok I made it!
Don't know how, maybe it was working all the time. I've seen that phone is connected thru Ports (COM & LPT). Opened KDZ again, even that the install for firmware usb driver failed. I again tried to flash, again there were errors (wparam,...) and port -1?, I just left phone connected, yesterday I unplugged it! After 10minutes phone restarted and here is 4.1.2 and all the data is here!
Don't know what I was doing =)
Thread can be closed now!
Great!
I am new to posting, but I have followed XDA for a long time and used it to install custom ROM's on other phones. However, I now have a problem with my wife's Samsung Galaxy GT-S5360L. I have searched for hours, but can not find a solution.
The phone is stuck in a boot loop. I can enter stock recovery mode. When I try to perform a factory reset, I get the following message:
E:format folume: rfs format failed on /dev/stl11
formatting /cache
Data wipe complete
After wiping the cache partition, the phone continues to be stuck in the same boot loop after reboot (Samsung logo appears on screen, followed by animation, back to Samsung logo).
The phone will not enter into download mode. When I press power+volume down+home, I see a white screen, followed by a black sreen, followed by another white screen. the suggested method of removing the battery, SIM, and SD card, and plugging into the computer while holding both volume buttons does not work. Odin will not recognize that the phone is connected.
I tried to connect the phone to two different computers. One runs Linux mint with Windows XP on a VM. This computer has always worked for flashing ROM's to other phones. Odin would not recognize the phone, and I received messages that the device was not properly installed.
I then tried to connect the phone to another computer with Windows Vista. This PC has Kies installed and Samsung drivers. Kies would not connect to the phone, and I also received messages that the device was not properly installed. Odin would not recognize the phone. I should note that the phone has interfaced with this computer sucessfully before.
This phone has never had a custom recovery or ROMs installed. It only has the original stock ROM. Is the phone's hardware defective, or can it somehow be fixed? Please post any links to threads that I may have missed. Thanks.
Download mode is only effected by a change in bootloader normally by Flashing incompatible firmware or a hardware fault
For flashing via odin kies is not required - its useless as it's not compaitable with the galaxy y for this purpose
You just need the Samsung USB drivers available from my firmware thread (links in signature)
It maybe possible to still flash the device
Once USB drivers installed
Enter download mode
Connect USB to pc
When the white screen appears push Vol up
Wait a few seconds
Open odin
Put the 3 firmware files in their places & flash
If it doesn't flash you will either need to flash a new bootloader via a jtag (repair shop) Or replace the motherboard - either way unless you can get it done very cheap it's more economical to buy a new phone
Thank you marcussmith2626 for your sound advice. The phone is working again. I will share the problems I solved in order to flash the stock ROM. Hopefully this will help anyone else that may have a similar problem.
The Samsung USB drivers had been previously installed on my PC running windows vista. I installed the drivers so that I did not have to use the bloated Kies software. However, when I tried to connect the corrupted phone to the PC via USB, it was not recognized, even though the correct drivers were installed. Below is the procedure I had to follow in order to connect the phone:
1. I connected the phone to the computer via USB. The phone had the battery installed and was powered off. After connecting to the computer, the phone started charging (battery icon on screen). Connecting in download mode at this point did not work. The phone must be powered off.
2. When the "found new hardware" notification box appeared, I had to make a note of each device that had been discovered.
3. I then had to open Device Manager from the control panel and find each device (the name in Device Manager matched the name in the new hardware notification).
4. I right clicked on each unknown device and selected "update driver software"
5. In the next menu, I selected "Browse my computer for driver software"
6. In the following menu, I selected "Let me pick from a list of drivers on my computer"
7. This brought up a list currently installed drivers. I selected the Samsung phone driver.
8. The driver then installed for the selected device..
9. Steps 2 through 9 were repeated for each new device discovered by Windows (each device listed in the "found new hardware" dialog).
10. I started the phone in boot mode (power+home+volume down, phone still connected to PC). I saw only a white screen. However, when I pressed the volume up button, the phone connected to the PC. Odin recoginized the phone and the stock ROM was flashed.
So, even if you only see a white screen, download mode can still be active. In my case, the drivers on the PC were not working correctly, probably due to the corruption of the original stock ROM. The drivers can only be added on my PC using the above method. The option to choose from a list of currently installed drivers was not available from the found new hardware wizzard.
Also, I will also say for reference that in the USA, the stock ROM from Brazil is the one that should be used so that the phone broadcasts on the proper GSM frequencies.
I own an LG G2, i recently got this phone yesterday from a person on craiglist. Don't worry i didn't pay him i gave him my older phone i dont use anymore. SO This phone is practically stuck in Firmware Update (As i read that post) , i spent about a day and half figuring it out and what happens is that.
I CAN get into recovery its TWRP v2.7.0.0 by Turning off the phone first and then Holding Vol UP, Power, Vol Down at the same time until the LG Logo comes up and then i am still holding them down, and it says Recovery Mode please wait and bam TWRP.
But heres the problem i can't mount my OTG and i can't ADB Sideload. So what do i do from here?? this guy rooted this phone and soft bricked it i think? and he wiped the phone but i also did when i had the chance and wiped it completly via recovery.
The only way i got into "Download Mode" / "Firmware Update" was to take the back cover off and unscrew a few screws on the side and unclip the battery for a few seconds and then plugged it back in and then I held the VOl UP button and plugged my USB into the phone and the other end is in my PC. My phone says "Download Mode please wait" and then prompted with the Firmware Update screen. BUT my pc doesnt detect the phone whatso ever and i've already installed drivers and etc from this forum ( http://forum.xda-developers.com/showthread.php?t=2432476 ) its the 2015 method that i downloaded.
so what do i have to do, i havent tried using different usb cables, the port seems fine to be plugged in since in TWRP it says 84+ so i meant its charging right? help me out guys idk what else to do or flash or anything.
IAmTechFreq said:
I own an LG G2, i recently got this phone yesterday from a person on craiglist. Don't worry i didn't pay him i gave him my older phone i dont use anymore. SO This phone is practically stuck in Firmware Update (As i read that post) , i spent about a day and half figuring it out and what happens is that.
I CAN get into recovery its TWRP v2.7.0.0 by Turning off the phone first and then Holding Vol UP, Power, Vol Down at the same time until the LG Logo comes up and then i am still holding them down, and it says Recovery Mode please wait and bam TWRP.
But heres the problem i can't mount my OTG and i can't ADB Sideload. So what do i do from here?? this guy rooted this phone and soft bricked it i think? and he wiped the phone but i also did when i had the chance and wiped it completly via recovery.
The only way i got into "Download Mode" / "Firmware Update" was to take the back cover off and unscrew a few screws on the side and unclip the battery for a few seconds and then plugged it back in and then I held the VOl UP button and plugged my USB into the phone and the other end is in my PC. My phone says "Download Mode please wait" and then prompted with the Firmware Update screen. BUT my pc doesnt detect the phone whatso ever and i've already installed drivers and etc from this forum ( http://forum.xda-developers.com/showthread.php?t=2432476 ) its the 2015 method that i downloaded.
so what do i have to do, i havent tried using different usb cables, the port seems fine to be plugged in since in TWRP it says 84+ so i meant its charging right? help me out guys idk what else to do or flash or anything.
Click to expand...
Click to collapse
I think the methods leave out that you need to change your phone to com port 41 on device manager > ports in order to be detected. Then you need to unplug it and reconnect to computer when the program shows waiting for device, with the phone in download mode already.
Also, to get to recovery you hold vol down and power, when the LG logo comes up release power and hold it again until the reset screen comes up.
To get to download mode you turn the phone off then hold up while plugging the USB cord in with it connected to pc... This launches download mode.
Sent from my LG-VS980 using XDA Free mobile app
Yoinx said:
I think the methods leave out that you need to change your phone to com port 41 on device manager > ports in order to be detected. Then you need to unplug it and reconnect to computer when the program shows waiting for device, with the phone in download mode already.
Also, to get to recovery you hold vol down and power, when the LG logo comes up release power and hold it again until the reset screen comes up.
To get to download mode you turn the phone off then hold up while plugging the USB cord in with it connected to pc... This launches download mode.
Sent from my LG-VS980 using XDA Free mobile app
Click to expand...
Click to collapse
Well you see man , I cant change anything in Device Manager since my phone isn't being detected. It didn't install drivers fully fully since my phone isnt recognized. Even in TWRP or "Download Mode/ Firmware Update" Nothing happens no drivers installing or anything even but it does boot it up to that point....and its just normal boot up i see the LG logo and my led goes from green to blueish in a smooth transition and it doesnt stop until i turn it off. The method i got into recovery is holding all those buttons down its not a problem for me to get into it. I also have another problem it doesn't seem to want to mount my usb otg by samsung.
what do i do
So i tried the otg route but I can't mount it. I have everything connected and once I go into recovery to mount usb-otg, nothing happens.
I just need some way to get a ROM.zip in my phone
Computer does not recognize my phone.
Stuck at LG logo unless I enter recovery.
Sideload doesnt work.
OTG doesnt work.
I've tried at least 4 different guides with no luck.
Why don't you manually install drivers from online?
ive tried
tzzeri said:
Why don't you manually install drivers from online?
Click to expand...
Click to collapse
ive tried that already and it doesnt list anything from the LG folder.
I realized the phone will say start the adb sideload feature. so, when i put the "abd sideload file.zip" command on my pc i just wait a few minutes and it says daemon not running on port 5037 and then start successfuly and then error :device not found.
it can seem to reognize my device wether its in recovery, or download mode or fastboot mode.
Try again in other pc that has never been conected to an LG Phone before. It can perfectly be a conflict with drivers installed in the OS.
I've tried man
AFter i cleaned the usb port in one of the chats or forums, i waited a day ovbiously without turning on the phone and cleaned the usb port with alchohal and a q tip and i plugged my phone into my computer and my PC detected something but it only says "Unknown Device" everytime no matter what pc i use it says that. nothing else. but before that none of my pcs would detect theirs a phone plugged in at all.
IAmTechFreq said:
AFter i cleaned the usb port in one of the chats or forums, i waited a day ovbiously without turning on the phone and cleaned the usb port with alchohal and a q tip and i plugged my phone into my computer and my PC detected something but it only says "Unknown Device" everytime no matter what pc i use it says that. nothing else. but before that none of my pcs would detect theirs a phone plugged in at all.
Click to expand...
Click to collapse
Might be a problem with the cord
Sent from my Motorola DynaTAC using XDA Free mobile app
tzzeri said:
Might be a problem with the cord
Sent from my Motorola DynaTAC using XDA Free mobile app
Click to expand...
Click to collapse
No there is no problem with your USB cord or port. You need to do following steps.
http://forum.xda-developers.com/showthread.php?t=2432476
https://www.youtube.com/watch?feature=youtu.be&v=g01Pa7cgdSM&app=desktop
Please let me know if you succeed.
All credit goes to #bender_007
I tried to downgrade from Kitkat to JB via flashtool this morning which I often successfully flashed with the same method. But while the flashing is going on and almost finish the flashing (system.img, userdata.img, etc. are already flashed), there seems to be some problem and popped out that the flashing is fail. And then the device does not boot up. While I tried to reconnect the device to PC, the PC cannot recognize the device as shown in the picture. Unable to process any further method. Does anyone in this forum knows how to recover the bricked device like this?
The phone starts? In a black screen?
If the PC detects it like that the phone has some energy and connection...
Does anything apears on the screen? Can you go to the Recovery Mod?
Have you tried to force the driver installation on that USB item that appears on device manager?
Do you have access via ADB or fastboot?
Did you nottest in what partition did the error message appeared?
Please provide some answers to these questions so i can try to help you...
RSGI_PT said:
The phone starts? In a black screen?
If the PC detects it like that the phone has some energy and connection...
9Does anything apears on the screen? Can you go to the Recovery Mod?
Have you tried to force the driver installation on that USB item that appears on device manager?
Do you have access via ADB or fastboot?
Did you nottest in what partition did the error message appeared?
Please provide some answers to these questions so i can try to help you...
Click to expand...
Click to collapse
Nothing on the screen. Not able to boot into recovery or adb is not working. The phone is just death. But, when I insert the usb cable, the pc can detect it. I even approach the Customer Care here in Aizawl, but they cannot fixed. Even when I followed the instruction as per one xda member posted here, The qualcom hs - 9006/8 is displayed on the device manager and when I tried to flashed it with emergency mode, the result always the same. FAILS
hruaiapunte said:
Nothing on the screen. Not able to boot into recovery or adb is not working. The phone is just death. But, when I insert the usb cable, the pc can detect it. I even approach the Customer Care here in Aizawl, but they cannot fixed. Even when I followed the instruction as per one xda member posted here, The qualcom hs - 9006/8 is displayed on the device manager and when I tried to flashed it with emergency mode, the result always the same. FAILS
Click to expand...
Click to collapse
Try this:
- Start GNQC with the phone disconnected
- Connect the Phone and see GNQC recognizes the QLoader
- If so, press power button until the phone vibrates
- Wait for the GNQC recognizes again the QLoader and press Download on Emergency Mode
Use this KIKAT ROM: https://docs.google.com/uc?id=0B8H5JoBDpTnJMGE2QTJPR0FWX0E
This worked for me, i had the phone completly died, not even recognized by the PC, waited a day and tried again.
Once the QLoader is recognized your good to go!!
I'm having another problem after that, now theres no GSM/3G signals....
I need a EFS backup with the TWRP recovery.... No one seems to have
RSGI_PT said:
Try this:
- Start GNQC with the phone disconnected
- Connect the Phone and see GNQC recognizes the QLoader
- If so, press power button until the phone vibrates
- Wait for the GNQC recognizes again the QLoader and press Download on Emergency Mode
Use this KIKAT ROM: https://docs.google.com/uc?id=0B8H5JoBDpTnJMGE2QTJPR0FWX0E
This worked for me, i had the phone completly died, not even recognized by the PC, waited a day and tried again.
Once the QLoader is recognized your good to go!!
I'm having another problem after that, now theres no GSM/3G signals....
I need a EFS backup with the TWRP recovery.... No one seems to have
Click to expand...
Click to collapse
my e7 died. you are stuck using flash tools. is not even recognized by most PCs. maybe it drain? I can do? help me
I have the same problem, screen is completely black after trying to instal newer official rom. When I connect it to PC, it detects "hid device". I tried power + volume buttons combinations, but nothing changes. Sometimes notification led turn red for a few seconds but nothing else. And once win xp randomly detected phone as that "q..." thing, but it doesn't anymore. What else can I do?
Can anyone help me? I tried everything and my phone is still hardbricked.
Hello guys
Today i received my E7 and i tried to update via the tool unfortunately something went wrong and now i cant open it nor fastboot or recovery. Some hours ago i tried to connect via usb and appeared on the GNQC but later it showed as unknow device. It was my first day with the phone. Right when i connect /disconnect the usb i can hear the sound but i cant do anything. Is it dead or i can revive it somehow?
It was the first day:crying::crying:
Reinstall the drivesbob the PC, press 30 secs on the power button than connect the phone to the PC. If appears a QLoader port use emergency download on gnqc 1.6.9.0
RSGI said:
Reinstall the drivesbob the PC, press 30 secs on the power button than connect the phone to the PC. If appears a QLoader port use emergency download on gnqc 1.6.9.0
Click to expand...
Click to collapse
PLZ HELP i try to update using this http://www.needrom.com/download/gionee-elife-e7-32g/comment-page-2/#comment-165291 but now my phone doest enen boot or fast boot or anything.. in the proces it said "firehose ping phone fail" and stopped updating since then my phone isnt booting or anything and my pc dont recognize it any more.. plz help
---------- Post added at 15:32 ---------- Previous post was at 15:29 ----------
RSGI_PT said:
The phone starts? In a black screen?
If the PC detects it like that the phone has some energy and connection...
Does anything apears on the screen? Can you go to the Recovery Mod?
Have you tried to force the driver installation on that USB item that appears on device manager?
Do you have access via ADB or fastboot?
Did you nottest in what partition did the error message appeared?
Please provide some answers to these questions so i can try to help you...
Click to expand...
Click to collapse
plz help...
PLZ HELP i try to update using this http://www.needrom.com/download/gion...comment-165291 but now my phone doest enen boot or fast boot or anything.. in the proces it said "firehose ping phone fail" and stopped updating since then my phone isnt booting or anything and my pc dont recognize it any more.. plz help
thianpa he thil hi i solve thei toh m
While flashing the phone through odin the phone failed on the system image. The firmware file is valid as it has been flashed previously with success. when the phone was rebooted again in download mode the PC will chime as if it can detect the phone at the warning screen although it isnt seen in device manager. as soon as I press Vol+ to continue the computer will say that the phone is an unknown device. No phone is present in device manager still and no error code returned to see what may be causing the connection issue. Along with that the smart switch screen appears rather then showing the usual screen that says Downloading.
No access to recovery or anything else as the phone immetiatly shows the smartswitch screen. When booted normaly the smartswitch screen is also accompanied by no response via usb to show connection not even the previously mentioned Unknown device error to indicate that the computer is even noticing a usb connection at all. All drivers are current.