Hello all
This is my first post here, but I have been reading a lot for some days now
So this is the issue
Some days ago I bought on ebay from a reputable seller the sgs2 stated as unlocked for all networks. This is a UK phone but I am located in portugal, and I use a vodafone sim card
Much to my surprise I was greeted with the O2 logo when turning it on.. oh well.. no big issue on that but...! right after entering my sim card pin code it asked for a network lock control key.!
Trying to avoid too much assle for being a newbie in android I bought an unlock code from mobileunlocked, and well, it didn´t work! says "requesting network unlock" over a fraction of a second and then right afterwards "network unlock request unsucessfull"
Ok, so I went the hard way and read all about firmware and rooting at the android development part of the forum
Was able to flash the XWKE7 / baseband XXKE4 with odin, was able to root it with intratech´s thourough instructions, no more O2 startups or logos, even installed the galaxy S2 sim unlock (it finds the same unlock code I got before, and it is probably right)
but.... the dam unlock code question does not go away, so I have no mobile network at all!
Seems it tries to communicate with O2 for the unlocking but of course I am nowhere near the UK..
So I have a fantastic up to date piece of brick in my hands!
Could someone please help, how can I get over this network unlock code ?
I am running out of options, please help!
best rgds
Buy a code from somewhere online instead. They're more reliable then the app unlock.
Samsung phones can be locked by 4 methods methods but generally the first three are what you are interested in .
1. [NCK] Network lock
2. [SCK] Subset lock
3. [SPCK] SP lock
4. [MCK]
o2 generally only lock down NCK
1 ensure you have down the correct IMEI number , when you got your network unlock code was it just the unlock code they gave you or did they supply the above too.
2. you do not need to have an O2 sim to unlock as the procedure means you need to put a different sim in to enable the codes .
3 mobileunlocked.co.uk are very good and if you contact them they will be able to help you . Send them an email .
Hope this helps but just make sure you entered the correct IMEI number *#06# from the start .
good morning
indeed they do, I bought from them. I had to enter the MCK and then the NCK
how could I know ? lolol
also thank you guys for your prompt help
turning on the little devil as I write... ta nan!
Is this possible?
I've just received my code and entered it with a disallowed SIM, it tells me network unlock successful but remains out of any kind of signal.
It then throws up the SIM unlock screen if I airplane mode on/off.
Is it possible to unlock via Android or will I need to reinstall some kind of Windows Mobile to do so?
Is it possibly just my ROM? (Typhoon).
My contract is up on the 28th so quick replies would be great
Can anyone help?
should work regardless of the os installed on the device, it unlocks it on a hardware level
i got my unlock code and used android to unlock and not had any issues, sounds like the code you have moight only be a temporary code
Richy99 said:
should work regardless of the os installed on the device, it unlocks it on a hardware level
i got my unlock code and used android to unlock and not had any issues, sounds like the code you have moight only be a temporary code
Click to expand...
Click to collapse
But the code doesn't actually allow me to use the (O2) SIM... It just says that it is unlocked.
What ROM?
I get a "SIM unlock successful" message regardless of what code I enter.
Tried on Typhoon, NexusHD Gingerbread and official MIUI.
Trying NexusHD Froyo to see if it's a GB issue :/
Hi. I recently bought the LG V35 supposedly unlocked; however, I am unable to activate on T-Mobile.
Backstory: After purchasing the V35, I followed the instructions on cross flashing to get rid of the AT&T bloat here https://forum.xda-developers.com/lg-v35/development/bootloader-unlock-root-instruction-t4052145. The firmware I downloaded was from https://lg-firmwares.com/lg-lmv350ulm-firmwares/; however, the AIO and the USA versions are both the same. I flashed one of the firmware and all is fine, except now I get "Network locked" after I insert my SIM card from T-Mobile. I went AT&T's site https://www.att.com/deviceunlock/#/https://www.att.com/deviceunlock/#/ for an unlock code; however, I do not get a prompt on my phone to enter the code. This is after I flashed the phone.
My questions are, which version of the firmware was I to use so my phone is network unlocked AIO or USA? If they are both the same, how do I get the phone to be network unlocked so I can activate the V35 to T-Mobile.
TIA
boricua65 said:
Hi. I recently bought the LG V35 supposedly unlocked; however, I am unable to activate on T-Mobile.
Backstory: After purchasing the V35, I followed the instructions on cross flashing to get rid of the AT&T bloat here https://forum.xda-developers.com/lg-v35/development/bootloader-unlock-root-instruction-t4052145. The firmware I downloaded was from https://lg-firmwares.com/lg-lmv350ulm-firmwares/; however, the AIO and the USA versions are both the same. I flashed one of the firmware and all is fine, except now I get "Network locked" after I insert my SIM card from T-Mobile. I went AT&T's site https://www.att.com/deviceunlock/#/[url]https://www.att.com/deviceunlock/#/[/url] for an unlock code; however, I do not get a prompt on my phone to enter the code. This is after I flashed the phone.
My questions are, which version of the firmware was I to use so my phone is network unlocked AIO or USA? If they are both the same, how do I get the phone to be network unlocked so I can activate the V35 to T-Mobile.
TIA
Click to expand...
Click to collapse
You need to be on AT&T firmware to use the carrier unlock code. If you cross flash to different firmware before carrier unlocking you are out of luck. EDIT: see posts below where new information has emerged.
Obviously your V35 was not carrier unlocked/SIM card unlocked, in spite of what the seller said?
Unlike with the LG V30 series, flashing carrier unlocked firmware does NOT carrier unlock AT&T LG V35. You need to use carrier unlock code prior to cross flashing different variant firmware.
Perhaps you can contact someone with Octoplus box and get back to AT&T firmware to use carrier unlock code. AT&T doesn't publicly release KDZ for their firmware, but some dealers with Medusa and Octoplus boxes still somehow have it.
boricua65 said:
Hi. I recently bought the LG V35 supposedly unlocked; however, I am unable to activate on T-Mobile.
Backstory: After purchasing the V35, I followed the instructions on cross flashing to get rid of the AT&T bloat here https://forum.xda-developers.com/lg-v35/development/bootloader-unlock-root-instruction-t4052145. The firmware I downloaded was from https://lg-firmwares.com/lg-lmv350ulm-firmwares/; however, the AIO and the USA versions are both the same. I flashed one of the firmware and all is fine, except now I get "Network locked" after I insert my SIM card from T-Mobile. I went AT&T's site https://www.att.com/deviceunlock/#/https://www.att.com/deviceunlock/#/ for an unlock code; however, I do not get a prompt on my phone to enter the code. This is after I flashed the phone.
My questions are, which version of the firmware was I to use so my phone is network unlocked AIO or USA? If they are both the same, how do I get the phone to be network unlocked so I can activate the V35 to T-Mobile.
TIA
Click to expand...
Click to collapse
My understanding is that if you flash the firmware for south america, when you boot it with your sim card, a pop up will appear asking for an unlock code. Haven't done it myself but it sounds like in your situation it wouldn't hurt to try...
Of course, if u don't get a pop up, try the code that supposedly brings up pop up to enter code.
follow this link for the MIA version that should work.
cheers, let us know if you try it the results.
Thread Cleaned and it will end here regarding this back and forth, take care.
Hi OP, use LGUP to flash Mexican region kdz, insert your T-Mobile sim and unlock window will pop-up upon reboot and you can use the unlock code to unlock your phone. Good luck.
Android# said:
Hi OP, use LGUP to flash Mexican region kdz, insert your T-Mobile sim and unlock window will pop-up upon reboot and you can use the unlock code to unlock your phone. Good luck.
Click to expand...
Click to collapse
Is this guaranteed to work? I really want to use this phone.
boricua65 said:
Is this guaranteed to work? I really want to use this phone.
Click to expand...
Click to collapse
Guaranteed? Well, as stated by those mentioning it here, I don't think we've actually done it, only repeating that others say it will work. So again, guaranteed? I couldn't guarantee it, but it seems unlikely that people would say it does work, and be lying about it?
Here's a GDrive link to the kdz you'd want to flash to try it. It's the latest Oreo for the south american region. Aside from using LGUP to flash it, you'd need an unlock code.
The md5 sum from this LG Page should match, to verify legitimacy.
Let us know if it works.
AsItLies said:
Guaranteed? Well, as stated by those mentioning it here, I don't think we've actually done it, only repeating that others say it will work. So again, guaranteed? I couldn't guarantee it, but it seems unlikely that people would say it does work, and be lying about it?
Here's a GDrive link to the kdz you'd want to flash to try it. It's the latest Oreo for the south american region. Aside from using LGUP to flash it, you'd need an unlock code.
The md5 sum from this LG Page should match, to verify legitimacy.
Let us know if it works.
Click to expand...
Click to collapse
So I just flashed my phone from the link you provided and no dice. I reflashed, factory reset, insert the SIM card after completing set up, insert SIM card after factory reset the second time, etc. with no luck. I am not getting a pop to ask for the unlock code.
EDIT to add: So I found a set of instructions when I don't get a pop up asking for the network unlock code (below)
Second option (device doesn't ask for an unlock code with an unaccepted SIM)
1. Start the device with an accepted simcard (example LG V35 ThinQ was bought in Orange you need to insert an Orange card)
2. Go to the dial screen and press “2945#*model number#” (the same way you enter a phone number)
Example: the device is a P999 you need to enter “2945#*999#” or for KU990 you need to enter “2945#*990#” etc…
So far I am getting closer. Now I get a message saying SIM not provisioned. I will continue to research and troubleshoot. If I continue to run into a another roadblock, I will post here. Thank you all.
Okay, now I fracked up something else. I went from V350EM10h_OPEN_SCA_OP_118.kdz to V350ULM20f_00_NAO_US_
Okay now I am stuck at the LG Life's Good splash screen. I went back to LGUP and did not see it was defaulted to Refurbish going from V350EM10h_00_OPEN_SCA_OP_0118.kdz to V350ULM20f_00_NAO_US_OP_0218.kdz. I went back and reran LGUP with Upgrade chosen; however, the phone is still stuck at the splash screen. Help!
EDITED
boricua65 said:
Okay now I am stuck at the LG Life's Good splash screen. I went back to LGUP and did not see it was defaulted to Refurbish going from V350EM10h_00_OPEN_SCA_OP_0118.kdz to V350ULM20f_00_NAO_US_OP_0218.kdz. I went back and reran LGUP with Upgrade chosen; however, the phone is still stuck at the splash screen. Help!
Click to expand...
Click to collapse
So you've tired to reflash ulm and have an issue there. But did you get it sim unlocked?
here's also some instructions I found re unlocking sim if you don't get a pop-up
UNLOCK LG UNLOCK INSTRUCTIONS
ONCE YOU HAVE RECEIVED THE UNLOCK CODE EMAIL, PLEASE FOLLOW THE FOLLOWING INSTRUCTIONS CAREFULLY.
1) Insert a SIM card that is not from the original carrier in your phone and power on the phone.
2) Once finished loading your phone will ask you for the "SIM Network Unlock PIN".
If your phone does not prompt for a code, please dial 2945#* [model number] # to bring up the prompt
For example LG G4 D851: Dial 2945#*851#
3) Enter the LG Network Unlock Code.
If your phone asks for the "SIM network unlock PIN", use the NCK code.
If your phone asks for the "SIM Service Provider unlock PIN", use the SPCK code.
---------------------
But now you have an additional issue, you say you used 'refurbish' mode for both flashings? To the S.A. one and then back to the ulm one?
To my understanding, that should have worked. But whatever the case may have been, you're stuck now, from what I understand. If that's the case, all I can suggest is trying 'DL' mode for the ULM and select all partitions, OR maybe try 'Upgrade' (if you did refurbish" or refurbish if you did the other.
Sorry to hear you're having trouble, I guess, if you followed the procedure and it didn't work, then this is an indication there IS NOT a way to unlock the sim if you failed to do it on ATT OS.
Let us know if you're able to make any progress / got it sim unlocked or not. We'll have to start relaying the results so others don't have the same issue.
AsItLies said:
So you've tired to reflash ulm and have an issue there. But did you get it sim unlocked?
here's also some instructions I found re unlocking sim if you don't get a pop-up
UNLOCK LG UNLOCK INSTRUCTIONS
ONCE YOU HAVE RECEIVED THE UNLOCK CODE EMAIL, PLEASE FOLLOW THE FOLLOWING INSTRUCTIONS CAREFULLY.
1) Insert a SIM card that is not from the original carrier in your phone and power on the phone.
2) Once finished loading your phone will ask you for the "SIM Network Unlock PIN".
If your phone does not prompt for a code, please dial 2945#* [model number] # to bring up the prompt
For example LG G4 D851: Dial 2945#*851#
3) Enter the LG Network Unlock Code.
If your phone asks for the "SIM network unlock PIN", use the NCK code.
If your phone asks for the "SIM Service Provider unlock PIN", use the SPCK code.
---------------------
But now you have an additional issue, you say you used 'refurbish' mode for both flashings? To the S.A. one and then back to the ulm one?
To my understanding, that should have worked. But whatever the case may have been, you're stuck now, from what I understand. If that's the case, all I can suggest is trying 'DL' mode for the ULM and select all partitions, OR maybe try 'Upgrade' (if you did refurbish" or refurbish if you did the other.
Sorry to hear you're having trouble, I guess, if you followed the procedure and it didn't work, then this is an indication there IS NOT a way to unlock the sim if you failed to do it on ATT OS.
Let us know if you're able to make any progress / got it sim unlocked or not. We'll have to start relaying the results so others don't have the same issue.
Click to expand...
Click to collapse
Actually, I was able to get the phone to be network unlocked. I mistakenly went from S.A. version to NAO as Refurbished instead of Upgrade on the LGUP.
boricua65 said:
Actually, I was able to get the phone to be network unlocked. I mistakenly went from S.A. version to NAO as Refurbished instead of Upgrade on the LGUP.
Click to expand...
Click to collapse
So you're all set now? sim unlocked and back on ULM? If that's so, that's good news.
AsItLies said:
So you're all set now? sim unlocked and back on ULM? If that's so, that's good news.
Click to expand...
Click to collapse
Only the phone is network unlocked. It's still stuck at the LG logo screen and does not boot up.
boricua65 said:
Only the phone is network unlocked. It's still stuck at the LG logo screen and does not boot up.
Click to expand...
Click to collapse
Well that's not good. I can only suggest try doing a partition D/L? I don't know if that would help or not, but not sure it could be worse than it is now? Certainly don't try the other options like chip erase etc. Those are not for a situation like this, they will certainly make things worse!
boricua65 said:
Hi. I recently bought the LG V35 supposedly unlocked; however, I am unable to activate on T-Mobile.
Backstory: After purchasing the V35, I followed the instructions on cross flashing to get rid of the AT&T bloat here https://forum.xda-developers.com/lg-v35/development/bootloader-unlock-root-instruction-t4052145. The firmware I downloaded was from https://lg-firmwares.com/lg-lmv350ulm-firmwares/; however, the AIO and the USA versions are both the same. I flashed one of the firmware and all is fine, except now I get "Network locked" after I insert my SIM card from T-Mobile. I went AT&T's site https://www.att.com/deviceunlock/#/https://www.att.com/deviceunlock/#/ for an unlock code; however, I do not get a prompt on my phone to enter the code. This is after I flashed the phone.
My questions are, which version of the firmware was I to use so my phone is network unlocked AIO or USA? If they are both the same, how do I get the phone to be network unlocked so I can activate the V35 to T-Mobile.
TIA
Click to expand...
Click to collapse
Sorry to tell you this but you can't network unlock after flashing. You should have researched that if you're modifying the phone
Vuzeultra said:
Sorry to tell you this but you can't network unlock after flashing. You should have researched that if you're modifying the phone
Click to expand...
Click to collapse
You did not ready the whole thread. I was able to network unlock my device after using a South American firmware. In my haste, I used LGUP and flashed the NAO firmware as a Refurbish instead as Upgrade.
AsItLies said:
Well that's not good. I can only suggest try doing a partition D/L? I don't know if that would help or not, but not sure it could be worse than it is now? Certainly don't try the other options like chip erase etc. Those are not for a situation like this, they will certainly make things worse!
Click to expand...
Click to collapse
With much trepidation, I did the Partition D/L and it work!!! :good::good::good: I got my phone back.
boricua65 said:
With much trepidation, I did the Partition D/L and it work!!! :good::good::good: I got my phone back.
Click to expand...
Click to collapse
Awesome, good job.
Hi all,
I'm trying to unlock my Redmi Note 7 following the lineageos installation guide (https://wiki.lineageos.org/devices/lavender/install), I get stuck at point 7 of "Unlocking the bootloader" section.
So, I haven't been able to unlock the phone yet because the Mi Unlock app fails at 99% reporting a generic error "Could not unlock device".
While I was repeating the procedure I noticed that, even though my sim is perfectly working (I have been using it for a couple of years now) and I have already connected it to my account, it shows that it is not activated. So I think, since it is a requirement for unlocking the phone, that this could be the problem.
I could not find anything useful online, since all problems related to the sim activation actually refers to a not working sim or detection problem, while I have a perfectly functioning connection (both data and sms) and the phone obviously detects it.
Any help?
Thanks
You test to change the SIM port
joke19 said:
You test to change the SIM port
Click to expand...
Click to collapse
I tried multiple times and the sim works in both cases but the result (in the screenshot above) is the same.
You activate it the SIM under developer osptions?
Yes, and it does it succesfully. Even though I can keep doing it and it keeps saying something like "account is now connected to this device", but the button is still there and I can *add it* again (I guess there is no check).
Apply for permissions to unlock Mi devices
en.miui.com
Test the unlock tool from here