Database Users

[Q] Bricked phone, any way to fix it?

I installed deodexed 4.2.2 stock when i was running deodexed 4.2.1 stock. i felt that it was buggy, so i went into cwrecovery and wiped it and i was about to begin reinstalling deodexed 4.2.2 again when i noticed i forgot to put it onto my phone. then i tried to use my phone, and it would be stuck at "unfortunately, system ui has stopped". it never leaves that popup, so i can't enable usb debugging. i can't use recovery mode, because when i do, the android with a triangle caution sign is there, but no options to select from. i can enter fastboot mode, but that's about it.

CM9onmyMoPho said:
I installed deodexed 4.2.2 stock when i was running deodexed 4.2.1 stock. i felt that it was buggy, so i went into cwrecovery and wiped it and i was about to begin reinstalling deodexed 4.2.2 again when i noticed i forgot to put it onto my phone. then i tried to use my phone, and it would be stuck at "unfortunately, system ui has stopped". it never leaves that popup, so i can't enable usb debugging. i can't use recovery mode, because when i do, the android with a triangle caution sign is there, but no options to select from. i can enter fastboot mode, but that's about it.
Click to expand...
Click to collapse
Reflash a factory image in fastboot, flash CWM/TWRP in fastboot, reroot and reflash the dedexed rom. Your phone isn`t even a bit bricked fortunately.

gee2012 said:
Reflash a factory image in fastboot, flash CWM/TWRP in fastboot, reroot and reflash the dedexed rom. Your phone isn`t even a bit bricked fortunately.
Click to expand...
Click to collapse
How can I reflash the factory image? and where can i find instructions? where can i find the link to download the factory image? thanks

CM9onmyMoPho said:
How can I reflash the factory image? and where can i find instructions? where can i find the link to download the factory image? thanks
Click to expand...
Click to collapse
Look in my signature line 2 and 3.

gee2012 said:
Look in my signature line 2 and 3.
Click to expand...
Click to collapse
thanks. will i lose any personal things such as photos?

CM9onmyMoPho said:
thanks. will i lose any personal things such as photos?
Click to expand...
Click to collapse
Everything will be lost. Considering your phone is bricked there is no way to pull the pictures from your device.
Edit: you might not have to flash full stock, just the system.img that will allow you to overwrite the current system and maintain your sdcard.

i do not know if this is the best place to post this considering i am brand new (i hope so) but i have a soft bricked nexus s 4g that i am trying to fix.
it was loaded with the helly bean 4.2.2 custom rom from nexus hacks (sorry no links) after the reboot it went to a black screen.
what ive tried:
odin: flashing a new rom, this resulted in odin not finding the device (usb debugging is not on and i cant turn it on)
fastboot: (i have all the files but i cant seem to get it set up, i type in adb or fastboot (no device recognized)
nexus root toolkit: (wouldnt find the device and found no options to help with usb debugging)
dfs: (couldnt read the device)
plugging in the phone to the computer: it makes the noise that it is plugged in, comes up as f drive but it is greyed out and i cant click on it (says insert disc)
clock work recovery: i did a full data wipe and required wipes cache and delvik or something along those lines: it reboots into the rom and nothing has changed.. my guess is because there is no back up of the original rom and the cfw is trash, it just wipes the bad rom back to factory and that is still a problem.
pda net: wont recognize the device
galaxy nexus toolkit: nothing useful since the usb debugging is not enabled.
ive worked for 6 hours as of last night to figure this out. i have spent most of those hours in forums and delving further into this phone then id imagined (its not mine) so if there is anyone out there that can suggest anything id appreciate it. this has got me stumped and amazed how such easy fix can really be this complicated.. i will thank any and all answers given to me

theblackrose666 said:
i do not know if this is the best place to post this considering i am brand new (i hope so) but i have a soft bricked nexus s 4g that i am trying to fix.
it was loaded with the helly bean 4.2.2 custom rom from nexus hacks (sorry no links) after the reboot it went to a black screen.
what ive tried:
odin: flashing a new rom, this resulted in odin not finding the device (usb debugging is not on and i cant turn it on)
fastboot: (i have all the files but i cant seem to get it set up, i type in adb or fastboot (no device recognized)
nexus root toolkit: (wouldnt find the device and found no options to help with usb debugging)
dfs: (couldnt read the device)
plugging in the phone to the computer: it makes the noise that it is plugged in, comes up as f drive but it is greyed out and i cant click on it (says insert disc)
clock work recovery: i did a full data wipe and required wipes cache and delvik or something along those lines: it reboots into the rom and nothing has changed.. my guess is because there is no back up of the original rom and the cfw is trash, it just wipes the bad rom back to factory and that is still a problem.
pda net: wont recognize the device
galaxy nexus toolkit: nothing useful since the usb debugging is not enabled.
ive worked for 6 hours as of last night to figure this out. i have spent most of those hours in forums and delving further into this phone then id imagined (its not mine) so if there is anyone out there that can suggest anything id appreciate it. this has got me stumped and amazed how such easy fix can really be this complicated.. i will thank any and all answers given to me
Click to expand...
Click to collapse
You need to be in the bootloader for fastboot to work. Reboot to bootloader and try flashing a recovery.img using this command.
fasboot flash recovery recovery.img

It blows my mind when a user gets all this great help and hasn't given any thanks to the helpers.
Sent from my iPad 4

mitchdickson said:
It blows my mind when a user gets all this great help and hasn't given any thanks to the helpers.
Sent from my iPad 4
Click to expand...
Click to collapse
Happens all the time. I'd have 1000 extra thanks if people new how to use the button or were remotely grateful.

estallings15 said:
Happens all the time. I'd have 1000 extra thanks if people new how to use the button or were remotely grateful.
Click to expand...
Click to collapse
i am sorry i was getting sdk tools set up watching an online tut. i am very greatful for your help my problem was that i had not installed java. so if anyone finds that sdk tools is not coming up. install java and it will work like it is supposed to. i will give a thank you just like i have promised. you guys on this site are the best techs hands down
---------- Post added at 05:13 PM ---------- Previous post was at 05:05 PM ----------
is there a thread on here about adb shell and pushing a new rom onto a nexus s 4g? basically the commands?

theblackrose666 said:
i am sorry i was getting sdk tools set up watching an online tut. i am very greatful for your help my problem was that i had not installed java. so if anyone finds that sdk tools is not coming up. install java and it will work like it is supposed to. i will give a thank you just like i have promised. you guys on this site are the best techs hands down
---------- Post added at 05:13 PM ---------- Previous post was at 05:05 PM ----------
is there a thread on here about adb shell and pushing a new rom onto a nexus s 4g? basically the commands?
Click to expand...
Click to collapse
adb push nameofrom.zip /sdcard/
Sent from my Nexus 4 using xda premium

ran sdk tools tried adb shell and nothing it wont read the device. we tried to push the .tar files to the phone using samsung galaxy nexus tool kit. it didnt work so hes going to take it to a repair but i think the device is toast on the account that usb debugging mode is no where in sight. if it does get fixed ill be sure to report how it got fixed. so anyone else who runs into the problem can get this fixed without a 20 dollar repair bill.

heat361 said:
Everything will be lost. Considering your phone is bricked there is no way to pull the pictures from your device.
Edit: you might not have to flash full stock, just the system.img that will allow you to overwrite the current system and maintain your sdcard.
Click to expand...
Click to collapse
will my computer even detect my phone? usb debugging is off and i can't see the phone's storage from my pc.

LG G2 Fastboot

Everything I found on this says volume + and power, which kicks me into download mode, not fastboot.
I've gone into adb and typed adb reboot bootloader, but that just restarts the phone and turns in on like normal.
I google the how to enter fastboot mode on LG G2 and can find plenty of post about being stuck in fastboot, but nothing on how to get into fastboot in the first place.
Found a tutorial here about setting up and using fastboot and thought I was set until I got to the part about "and using fastback", where it just says:
Make sure you have android debugging turned on in your phone (not really needed for fastboot but you do need for ADB), plug it into your computer and boot into fastboot mode...
I felt like watching "Much ado about nothing" when Denzel says; "The learned constable is too cunning to be understood"
Any direction is appreciated.

Hmm, I may have written that guide... Just checked and yeah should have been more clear I'll change that up. It should have read the USB debugging was needed for adb (not for fastboot) so when you can issue
adb reboot bootloader
But after that I did mention to check device specific forum for answers on how to get into fastboot/bootloader and being I've never held an lg g2 I took a quick look around.
Unfortunately the only way that I found that people said works every time is to wipe recovery to get into bootloader mode as the recovery you guys currently have disables something due to a patch getting custom recoveries to work
So yeah, I would advice to speak with someone knowledgeable about your specific device before you just wipe recovery
Out of curiosity, is there something specific you need to do with fastboot or are you just curious about your phone?
Sent from my Nexus 7 using XDA Premium 4 mobile app

demkantor said:
Out of curiosity, is there something specific you need to do with fastboot or are you just curious about your phone?
Click to expand...
Click to collapse
the current thing I've been trying to straighten out is that despite being rooted and installing TWRP, I can't install ROMS. I tried CM 11 and Hellfire so that I could put kitkat on, but gave the following:
Error executing updater binary zip.
One of the answers I found said that I had to go back to TWRP 2.3 (I'm using 2.6) and I believe that's where the whole bootloader thing came into play, because it was the way to 'downgrade' -
So then I found Philz touch 6 (as I understand it a mode of CM 11), but here he talked about fastboot and lokifying items. Here's the link:
http://forum.xda-developers.com/showthread.php?t=2554053
In the end it still comes back to the "can't load ROMs" issue. Just want a completely stripped down Kitkat that I can add the stuff I want without the bloatware.
Thanks in advance.(and the thanks button was hit on your reply)

For KitKat you should need a newer recovery with SELinux support which I believe is 2.6.x and newer for twrp, 2.3 I doubt would work if there even is one for your phone
But yes fastboot is often the best way to change recoveries but not the only way.
If there is a flashable.zip you could install new recovery from old
If your current ROM supports the flash image binary you can use a terminal emulator
You can use adb to install
Or even apps from the market
I would look for the latest recovery for your device, twrp, cwm, shouldn't matter so long as its new and then find what way works best changing for your phone.
The update-binary issue is often a sign that you need to change recoveries
Unfortunately without having your device I don't know if I can give you the best answers but feel free to ask
Best of luck!
Sent from my Nexus 4 using XDA Premium 4 mobile app

demkantor said:
Unfortunately without having your device I don't know if I can give you the best answers but feel free to ask
Best of luck!
Click to expand...
Click to collapse
Thanks again. I have adb and the script for loading TWRP 2.6.xx. I unrooted and rerooted the phone, because I wasn't sure how to replace the recovery... Now I think I realize that I could just find another recovery image and place it in the same file as the loki flash and that will flash it (At least that's what I understand at present).
If that's the case, then downloading the Philz touch 6 would work... but not wanting to brick it, I'm still asking and reading.

Hello Guys.
I am having a similar issue. I have a new ROM that will not run because of a faulty lg set up wizard that always force closes and I can not get passed it and a nandroid that for some reason is corrupted. So. This fastboot seems to be a dead end it looks like a quick learning curve of ADB is the only viable answer. I have installed all SDK Manager with ADB Tools and also the required Jarva JDK and LG drivers. The phone is turned on (at the beginning of the faulty setup wizard) In CMD my device is found when typing in 'adb devices' So. I am already to push a new ROM over to the phone.
Do either of you guys know the adb command?
Help would be appreciated.
Thanks

You can't actually flash a new ROM with adb, but you can either push it phone with adb and then flash in recovery. Or if your recovery has an option for adb sideload then use this.
Also setup wizard crashing is usually the fault of wrong gapps or not wiping before flashing a rom
Sent from my Nexus 4 using XDA Premium 4 mobile app

I found that the best way was to load flashify, that did the trick so I could start trying out ROMs... so no on to the next step - finding a 4.4.2 stripped down stock and the LG stuff I actually like.... thanks again.

demkantor said:
You can't actually flash a new ROM with adb, but you can either push it phone with adb and then flash in recovery. Or if your recovery has an option for adb sideload then use this.
Also setup wizard crashing is usually the fault of wrong gapps or not wiping before flashing a rom
Sent from my Nexus 4 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Thanks for the reply!
I know it's not possible to flash a ROM via ADB. I have everything set up, ADB etc, etc. My phone is turned on and adb is seeing it but I can not work out the command to push. Every time I try to push I just get a long list of ADB instructions (I think they are) but nothing gets pushed. I have read lots of instructions on how to make the command but I still must be doing something wrong.
Here are my parameters;-
adb push/C:\Users\dene\Desktop/cm-11-20140210-SNAPSHOT-M3-d802.zip/sdcard
Am I missing some spaces I am not aware of? Are all my slashes the right way round and in the right places? Is my 'sdcard' destination designation correct seeing as there is only internal storage on the G2?
Another problem I am having is that ADB has no problem seeing my sevice EXCEPT when I boot in to recovery (TWRP). When in recovery I lose coms between my device and pc. Hence I can no do TWRP ADB side load (I have tried). I have all the correct LG drivers loaded. Except MTP keeps failing to install? Any ideas?
Not to be mardy about it or hassle you but I am fairly house bound and live out in the country and really require my mobile phone. I have spent many hours trying to figure this out. Any help with the above would be much appreciated?
PS. I did a very thorough wipe, I always do. The gapps are built in to this ROM!
Thanks

dodge3003 said:
Thanks for the reply!
I know it's not possible to flash a ROM via ADB. I have everything set up, ADB etc, etc. My phone is turned on and adb is seeing it but I can not work out the command to push. Every time I try to push I just get a long list of ADB instructions (I think they are) but nothing gets pushed. I have read lots of instructions on how to make the command but I still must be doing something wrong.
Here are my parameters;-
adb push/C:\Users\dene\Desktop/cm-11-20140210-SNAPSHOT-M3-d802.zip/sdcard
Am I missing some spaces I am not aware of? Are all my slashes the right way round and in the right places? Is my 'sdcard' destination designation correct seeing as there is only internal storage on the G2?
Another problem I am having is that ADB has no problem seeing my sevice EXCEPT when I boot in to recovery (TWRP). When in recovery I lose coms between my device and pc. Hence I can no do TWRP ADB side load (I have tried). I have all the correct LG drivers loaded. Except MTP keeps failing to install? Any ideas?
Not to be mardy about it or hassle you but I am fairly house bound and live out in the country and really require my mobile phone. I have spent many hours trying to figure this out. Any help with the above would be much appreciated?
PS. I did a very thorough wipe, I always do. The gapps are built in to this ROM!
Thanks
Click to expand...
Click to collapse
I HAVE SOLVED THE ISSUE! Thanks for your assistance mate but in the end I just went back to stock using this amazing thread:-
http://forum.xda-developers.com/showthread.php?t=2432476
in conjunction with this amazing video;-
http://www.youtube.com/watch?v=IixQjo_hyz8
So! I am now un rooted and back to stock. Time to start the rooting ana ROMing all over again.lol
Thanks

Glad to here!
You need a space after push
But it usually easier not to enter the location of a file while pushing so cd to the directory first like
cd C:\Users.....
Then once there adb push /nameoffile /locationonphone
But if you don't want to cd, I see you have widows, depending on version you can just right click in the folder your file is located and choose open cmd here
Sent from my Nexus 7 using XDA Premium 4 mobile app

Need Help
As I thought I bought LG G2 D-802, but it was D-800 and I accidentally install the lollipop of D802 and now it's in bootlap.... I can only get into fastboot and whenever I try to flash .img of D-800 or D-802 it just stuck at "writing .img"
What to do to unbrick the phone and bring it back to live. I tired the adb and fastboot cmd method on windows 10 and windows 7 but no success. It's just stuck at writing .img file.

Bootloader Unlock issue

EDIT: Well after a few hours of bashing around at it I managed to get the bootloader unlocked. However I am having one wicked time trying to get twrp installed as my recovery, and to S-off my device.
When I got to run : fastboot flash recovery twrp.img I get the error "unable to load twrp.img" Now I know darn good and well it is prob some stupid error on my part, but this is driving me batty and help would be greatly appreciated.
Brad
OK..Maybe I'm dumb...but I'd rather post a question than screw around and brick my phone.
Admittedly it has been a couple years since I had an HTC device. (Just got a Bolt today) Been to HTC Dev unlock to try and unlock my bootloader however I am running into an issue when trying to run oem get_identifier_token. Getting 'fastboot' is not recognized as an internal or external command. operable program or batch file.
Been thru this a couple times before on older HTC Devices (last one was an M8-HK Edition) and not had issues.
I installed everything it said to on the HTC site. But I'm stalled out at step 5 on the HTC Dev site. and can't seem to get any further than that. (and yes phone is in DL mode)
Anyone kind enough to help an old dummy out?

PodCulture said:
EDIT: Well after a few hours of bashing around at it I managed to get the bootloader unlocked. However I am having one wicked time trying to get twrp installed as my recovery, and to S-off my device.
When I got to run : fastboot flash recovery twrp.img I get the error "unable to load twrp.img" Now I know darn good and well it is prob some stupid error on my part, but this is driving me batty and help would be greatly appreciated.
Brad
OK..Maybe I'm dumb...but I'd rather post a question than screw around and brick my phone.
Admittedly it has been a couple years since I had an HTC device. (Just got a Bolt today) Been to HTC Dev unlock to try and unlock my bootloader however I am running into an issue when trying to run oem get_identifier_token. Getting 'fastboot' is not recognized as an internal or external command. operable program or batch file.
Been thru this a couple times before on older HTC Devices (last one was an M8-HK Edition) and not had issues.
I installed everything it said to on the HTC site. But I'm stalled out at step 5 on the HTC Dev site. and can't seem to get any further than that. (and yes phone is in DL mode)
Anyone kind enough to help an old dummy out?
Click to expand...
Click to collapse
1. make sure you're in download mode, not bootloader
2. make sure twrp.img is in your sdktools folder
maybe a bad download of twrp?

The saga continues...
Now Im stuck in this weird loop after S-off getting this screen:
It says "your phone is encrypted" enter your lock screen password. I did and it said correct, but your data is corrupted. You must do a factory reset. I try that process, the phone reboots, comes back up to that same "your phone is encrypted"
PodCulture said:
EDIT: Well after a few hours of bashing around at it I managed to get the bootloader unlocked. However I am having one wicked time trying to get twrp installed as my recovery, and to S-off my device.
When I got to run : fastboot flash recovery twrp.img I get the error "unable to load twrp.img" Now I know darn good and well it is prob some stupid error on my part, but this is driving me batty and help would be greatly appreciated.
Brad
OK..Maybe I'm dumb...but I'd rather post a question than screw around and brick my phone.
Admittedly it has been a couple years since I had an HTC device. (Just got a Bolt today) Been to HTC Dev unlock to try and unlock my bootloader however I am running into an issue when trying to run oem get_identifier_token. Getting 'fastboot' is not recognized as an internal or external command. operable program or batch file.
Been thru this a couple times before on older HTC Devices (last one was an M8-HK Edition) and not had issues.
I installed everything it said to on the HTC site. But I'm stalled out at step 5 on the HTC Dev site. and can't seem to get any further than that. (and yes phone is in DL mode)
Anyone kind enough to help an old dummy out?
Click to expand...
Click to collapse

PodCulture said:
Now Im stuck in this weird loop after S-off getting this screen:
It says "your phone is encrypted" enter your lock screen password. I did and it said correct, but your data is corrupted. You must do a factory reset. I try that process, the phone reboots, comes back up to that same "your phone is encrypted"
Click to expand...
Click to collapse
yes, after s-off u have to format data

OMJ said:
yes, after s-off u have to format data
Click to expand...
Click to collapse
I've no problem doing that, but teh phone isn't letting me do it.

PodCulture said:
I've no problem doing that, but teh phone isn't letting me do it.
Click to expand...
Click to collapse
How are you trying to format data?
Sent from my unknown using XDA Labs

Unlocked needs root and twrp
Honestly...I don't know where I screwed up. (in the various how-to's I read I didn't see a format data step) I took the phone to Sprint and they were kind enough to flash it for me...so I am back up and running. Booted into DL mode and verified that I'm still unlocked and S-off. But where to go from here I don't know. I'd love to flash twrp and SU, but paranoid about semi-bricking it again. I used to know how this crap worked but that was quite awhile ago. (a couple phones and a couple versions of Windows ago)
OMJ said:
How are you trying to format data?
Sent from my unknown using XDA Labs
Click to expand...
Click to collapse

PodCulture said:
Honestly...I don't know where I screwed up. (in the various how-to's I read I didn't see a format data step) I took the phone to Sprint and they were kind enough to flash it for me...so I am back up and running. Booted into DL mode and verified that I'm still unlocked and S-off. But where to go from here I don't know. I'd love to flash twrp and SU, but paranoid about semi-bricking it again. I used to know how this crap worked but that was quite awhile ago. (a couple phones and a couple versions of Windows ago)
Click to expand...
Click to collapse
flashing twrp & SU isn't difficult...since you unlocked bootloader, you should already have the fastboot tools needed.
1. download latest twrp (3.1.1-0 as of now) https://dl.twrp.me/pme/twrp-3.1.1-0-pme.img
2. copy that img to your sdktools/fastboot folder
3. reboot into download mode
4. flash twrp: fastboot flash recovery twrp-3.1.1-0-pme.img
5. reboot to bootloader, then reboot to recovery
6. create a backup if u want
7. flash/install SuperSU https://s3-us-west-2.amazonaws.com/supersu/download/zip/SuperSU-v2.82-201705271822.zip

Thanks! Got everything back up and running now. Nice to have a phone I can use the way I want to again. TONS of bloat though.
OMJ said:
flashing twrp & SU isn't difficult...since you unlocked bootloader, you should already have the fastboot tools needed.
1. download latest twrp (3.1.1-0 as of now) https://dl.twrp.me/pme/twrp-3.1.1-0-pme.img
2. copy that img to your sdktools/fastboot folder
3. reboot into download mode
4. flash twrp: fastboot flash recovery twrp-3.1.1-0-pme.img
5. reboot to bootloader, then reboot to recovery
6. create a backup if u want
7. flash/install SuperSU https://s3-us-west-2.amazonaws.com/supersu/download/zip/SuperSU-v2.82-201705271822.zip
Click to expand...
Click to collapse

How did u get s off

ROOT with PIE Guide

Hi All,
In the best interest to provide clarity I'm creating this quick and easy tutorial on how to root your Razer Phone 2 after the Pie Upgrade. Please send me any feedback to improve this post, we need to build up a strong community.
*As usual, I'm not responsible of any damage or brick to your phone, do it at your own risk.
Pre-Requirements:
-Be sure to have at least 70% of charges... or plug your phone to power
-Backup anything you consider important
-Already installed Pie Upgrade via OTA or Side Loaded​
-Enable Developer Options
• Open Phone "Settings" and scroll down.
• You will see an option "Build Number".
• Simply tap on it 7 times to enable it on your Android Oreo based device.
• Your device immediately display a message on screen that will say "You are now a developer".
• The Developer Option is now available in the Settings>System>Developer Options. Enjoy!​
- Install Android Drivers (https://developer.android.com/studio/run/win-usb) and ADB, I personally recommend -[TOOL]Minimal ADB and Fastboot [2-9-18] - https://forum.xda-developers.com/showthread.php?t=2317790
-Unlock Bootloader
• To enable OEM unlock, go to Settings > Developer options and check Enable OEM unlock
• Using ADB commands reboot on bootloader​
adb reboot bootloader​
• After reboot completes follow phone menus and select "UNLOCK BOOTLOADER"; accept all warnings, after restart you have completed the unlock.​
Root and Installing Magisk
Since our phone doesn't have a proven customer recovery fully working (Ex TWRP) Magisk needs to be installed by manually patching the device boot image.
Making leverage of Warrior1988 post [Root Magisk Pie Update For Unlocked Devices] all credits to him. Download the image from his post
• Boot in fastboot mode To boot into fastboot, press and hold the Power button + Volume Down Keys for few seconds; Copy the image on the same folder as your ADB and Run the following commands:
fastboot flash boot_a boot.img
fastboot flash boot_b boot.img
fastboot reboot​
Install Magisk Download the apk and install it as usual on your RP2, that should be all.
DONE!!!! You now have a unleashed the beast! Please send me any recommendations to improved this guide.

chpimentelpr said:
Install Android Drivers and ADB
Click to expand...
Click to collapse
Your link has everything necessary for this step, right? Direct link to version 1.4.3 is here: https://androidfilehost.com/?fid=746010030569952951
Or are drivers and ADB two separate downloads?
chpimentelpr said:
• To enable OEM unlock, go to Settings > Developer options and check Enable OEM unlock
Click to expand...
Click to collapse
I assume this is where we plug our phone into our computer?
chpimentelpr said:
• Using ADB commands reboot on bootloader
Click to expand...
Click to collapse
For anyone dumb and new like me, I think this is with cmd.exe in Windows. Win+S -> type "cmd" (without quotation marks) and hit enter. Once open, you want to navigate to ADB, which you've already installed via the above instructions.
So your cmd will say:
C:\Users\YourName>
And you want to get to ADB, so you'll type "cd" (without quotation marks) which means you want to change directories, and then "cd adb" (if its in C:\ directory) or "cd [whatever the path is to the ADB folder]\adb"
Assuming it was directly in C:, you should see something like:
C:\adb>
Now you want to type "adb devices" to make sure it sees your phone is plugged in. You should see: "list of devices attached - [model] device" or something.
Now you're ready to go with the instructions starting at "adb reboot bootloader." If I'm wrong about this, someone less new and dumb than I am please correct me.
chpimentelpr said:
• Copy the image on the same folder as your ADB and Run the following commands:
fastboot flash*boot_a boot.img
fastboot flash boot_b boot.img
fastboot reboot
Click to expand...
Click to collapse
I'm confused on this one. The first one has "flash*boot_a," but the second one has "flash boot_b" without the * symbol. What does the * do, and what happens if we mess it up? Sorry if that's a dumb question.

AbsoluteContingency said:
Your link has everything necessary for this step, right? Direct link to version 1.4.3 is here: https://androidfilehost.com/?fid=746010030569952951
Or are drivers and ADB two separate downloads?
I assume this is where we plug our phone into our computer?
For anyone dumb and new like me, I think this is with cmd.exe in Windows. Win+S -> type "cmd" (without quotation marks) and hit enter. Once open, you want to navigate to ADB, which you've already installed via the above instructions.
So your cmd will say:
C:\Users\YourName>
And you want to get to ADB, so you'll type "cd" (without quotation marks) which means you want to change directories, and then "cd adb" (if its in C:\ directory) or "cd [whatever the path is to the ADB folder]\adb"
Assuming it was directly in C:, you should see something like:
C:\adb>
Now you want to type "adb devices" to make sure it sees your phone is plugged in. You should see: "list of devices attached - [model] device" or something.
Now you're ready to go with the instructions starting at "adb reboot bootloader." If I'm wrong about this, someone less new and dumb than I am please correct me.
I'm confused on this one. The first one has "flash*boot_a," but the second one has "flash boot_b" without the * symbol. What does the * do, and what happens if we mess it up? Sorry if that's a dumb question.
Click to expand...
Click to collapse
fastboot flash boot_a boot.img
fastboot flash boot_b boot.img
fastboot reboot

Warrior1988 said:
fastboot flash boot_a boot.img
fastboot flash boot_b boot.img
fastboot reboot
Click to expand...
Click to collapse
No asterisk. Cool. Got it. Thank you, dude.

The drivers are the regular ones for android nothing specific, they can be downloaded from their SDK https://developer.android.com/studio/run/win-usb

App root detection?
If I root my Razer phone 2 using this guide, will certain apps like banking apps, and rideshare apps be able to detect root?

Bounty33 said:
If I root my Razer phone 2 using this guide, will certain apps like banking apps, and rideshare apps be able to detect root?
Click to expand...
Click to collapse
You can use magisk to hide the root from those apps. In general banking app are not affected by root. Google pay could be affected, but I don't use it so can't be sure. And you can always unroot.

AbsoluteContingency said:
No asterisk. Cool. Got it. Thank you, dude.
Click to expand...
Click to collapse
Did you rooted? Anything missing on the guide? I want make it as useful as possible so feedback is welcome.

chpimentelpr said:
Did you rooted? Anything missing on the guide? I want make it as useful as possible so feedback is welcome.
Click to expand...
Click to collapse
I have not, but I've been really sick and useless. I think I'll try tonight and let you know how it goes. Thanks for the guide, dude.
---------- Post added at 02:50 PM ---------- Previous post was at 02:45 PM ----------
Wait, yes, I do have a question. I download the drivers, and I download the Fastboot ADB thing. What do I do with the drivers? Do they just install in Windows like anything else, and that allows me to connect to the phone?

AbsoluteContingency said:
I have not, but I've been really sick and useless. I think I'll try tonight and let you know how it goes. Thanks for the guide, dude.
---------- Post added at 02:50 PM ---------- Previous post was at 02:45 PM ----------
Wait, yes, I do have a question. I download the drivers, and I download the Fastboot ADB thing. What do I do with the drivers? Do they just install in Windows like anything else, and that allows me to connect to the phone?
Click to expand...
Click to collapse
Yes, install them as any other driver.

After rooting can you relock the boot loader or will that brick the phone?

ndragon798 said:
After rooting can you relock the boot loader or will that brick the phone?
Click to expand...
Click to collapse
Not sure, but why you want to relock the boot.

chpimentelpr said:
Not sure, but why you want to relock the boot.
Click to expand...
Click to collapse
Mostly to get rid of the startup message

Very nice. I've rooted a ton of phones over the years, but they had more established communities and had well-explained (and tested) methods of rooting. The previous guide posted (that you referenced) was fine enough, but it was very much lacking a couple prerequisites that I was wondering/concerned about. This guide has cleared all of that up for me, and I now feel confident about rooting this phone.
Just as soon as I charge up the phone and install the OTA I've been avoiding until now... lol. Hoping somebody will make a Magisk module to move the clock back to where it belongs (if they haven't already).
EDIT: Just wanted to add my success story to this. Only thing I had to do that wasn't listed in the instructions (but makes sense) is that fastboot didn't work until I enabled USB Debugging (again, after the wipe and reboot), and I had to very manually tell the computer which driver to use (ADB) after that. Didn't have that issue for the bootloader instructions beforehand (that time, the driver worked automatically), so I figured I'd mention it.

chpimentelpr said:
Not sure, but why you want to relock the boot.
Click to expand...
Click to collapse
Also is there a way to turn back on the preboot authentication. Pretty much I just want to maintain full encryption and the built in security while having root.

ndragon798 said:
Also is there a way to turn back on the preboot authentication. Pretty much I just want to maintain full encryption and the built in security while having root.
Click to expand...
Click to collapse
I don't believe encryption is supported at the moment, and I don't encourage you to try it until TWRP is fully supported since you may end up in a boot loop. I'm eagerly waiting for the full encryption capability, so I will let you know as soon as something come up.

This has to be......one of the most usefull and noob friendly guides i have ever seen.....
You sir....are a God
Thank You.

ChronosTrigger said:
This has to be......one of the most usefull and noob friendly guides i have ever seen.....
You sir....are a God
Thank You.
Click to expand...
Click to collapse
i'm glad it helps.

Alright so after fighting with windows for a few hours, I discovered that my ADB was severely outdated.... Lesson learned there.
After getting the new boot image installed, though, I hit another problem... WiFi refuses to work. The toggle switch in the statusbar, nor the toggle in the system settings, will bring my wifi to life. Which is weird! Because I got through setup just fine, connected to wifi and signed into google... Yet now all wifi functionality has vanished. I tried a factory reset, to no avail. I'm gonna have to restore the factory boot image and start all over... But for now, figured I'd ask if anyone else has run into this weird bug?
***update***
I've now gone and flashed the global image for 8.1.0 to the phone... and it's telling me the OS is up to date???? How do I get back to pie?? It's late here and I've got wifi back now... but I'm stumped. Any help would be so greatly appreciated!

xttweaponttx said:
Alright so after fighting with windows for a few hours, I discovered that my ADB was severely outdated.... Lesson learned there.
After getting the new boot image installed, though, I hit another problem... WiFi refuses to work. The toggle switch in the statusbar, nor the toggle in the system settings, will bring my wifi to life. Which is weird! Because I got through setup just fine, connected to wifi and signed into google... Yet now all wifi functionality has vanished. I tried a factory reset, to no avail. I'm gonna have to restore the factory boot image and start all over... But for now, figured I'd ask if anyone else has run into this weird bug?
***update***
I've now gone and flashed the global image for 8.1.0 to the phone... and it's telling me the OS is up to date???? How do I get back to pie?? It's late here and I've got wifi back now... but I'm stumped. Any help would be so greatly appreciated!
Click to expand...
Click to collapse
I doubt the issue with the wifi is related with the image, since it doesn't have anything to do with it. If your phone doesn't detect the update you will need to sideload it. Then try the root guide again. Let us know how it goes, it the first time I hear something wrong with WIFI after rooting.

Any way to pull files in sideload/fastboot mode?

Hi, I've come to these forums because you guys are knowlegeable.
I essentially uninstalled thorugh ADB the package installer (com.google.android.packageinstaller) and little did I know that was a big mistake on my part, as I didn't realize the package installer was a core part of the system. All was going well until i turned on and off my phoen, and it is now always stuck in recovery mode.
- Rebooting the phone just sends me back to the menu.
- I've not tried wiping the data yet, since I want to keep my files (for the moment).
- Connect with MiAssistant allows me to connect my phone to my PC, but it in sideload mode automatically. I can go in fastboot mode though, and fortunately I have turned USB Debugging on.
As I've come to realize, a factory reset or flashing a ROM would fix my issue, but also delete all my files (photos, music...). I was planning to do a backup of my photos, but now it's too late.
Is there any way I can access my files and pull them to my PC on sideload/fastboot mode?
The only thread i have seen with a similar problem is this one: https://forum.xda-developers.com/sho....php?t=2487147
I also get the error:closed when I try an adb pull.
Thanks in advance.

guembo said:
....I essentially uninstalled thorugh ADB the package installer (com.google.android.packageinstaller) and little did I know that was a big mistake on my part, as I didn't realize the package installer was a core part of the system. All was going well until i turned on and off my phoen, and it is now always stuck in recovery mode.....
Click to expand...
Click to collapse
You have omitted some core information from your writeup:
1. Is your bootloader unlocked?
2. Which version of MIUI are you running?
3. Which recovery are you using?
One might hazard a guess about these questions, but that would not be a sensible basis for proposing possible solutions.

DarthJabba9 said:
You have omitted some core information from your writeup:
1. Is your bootloader unlocked?
2. Which version of MIUI are you running?
3. Which recovery are you using?
One might hazard a guess about these questions, but that would not be a sensible basis for proposing possible solutions.
Click to expand...
Click to collapse
1. My bootloader was locked.
2. MIUI Global 11.0.8
2. Recovery 3.0
I realized having the bootloader meant it was pretty much impossible to get my data back. I've been searching for answers for the past 3 days and honestly my patience just ran out.
Decided to just factory reset the phone and that's that.
Thank you for your willingness to help me though. Appreciated.

guembo said:
1. My bootloader was locked.
2. MIUI Global 11.0.8
2. Recovery 3.0
I realized having the bootloader meant it was pretty much impossible to get my data back. I've been searching for answers for the past 3 days and honestly my patience just ran out.
Decided to just factory reset the phone and that's that.
Thank you for your willingness to help me though. Appreciated.
Click to expand...
Click to collapse
Unfortunately, with a locked bootloader, the options are limited.