Moto X pure Boot only recovery - X Style (Pure) Q&A, Help & Troubleshooting

Good Morning everybody,
so yesterday was a rough day and when it eventually end i recive the october security update on the phone, without thinking i installed it and the phone does not boot up , instead i face my recovery (TWRP 3.1.1-0).
Of course i've made a mess because i was on stock rooted 7.0 on my retEU XT1572 phone with unlocked bootloader and status 3
i've tryed to restore a previous nandroid backup wihtout success, so today i downloaded the new RESURRECTION REMIX v5.8.4 (4 december wich is based on stock android 7) but i have no luck even with that...
Do i miss something?is there any rom to try with now? or i have to make a downgrade of my firmware to make it work again?
thanks in advice!
UPDATE:
phone boot now but always in recovery and after rebooting in bootloader i can reboot system from there.. it seems that if you download an update and the install process doesen't go in place every time you restart the device it always try to re-flash it, that's why i'm always in recovery.. i foun a similar post with this solution but i think it need some changes before it will work on our device (but i don't have the knowledge to set it right :S )
LAST UPDATE:
boot fixed by using this command in twrp recovery
dd if=/dev/zero of=/dev/block/platform/f9824900.sdhci/by-name/misc
misc file running at the startup redirecting the boot in the recovery, put blank in the file let the system boot up normally

You missed very much.
Here is stock RetEu, before october update:
https://forum.xda-developers.com/moto-x-style/general/stock-xt-1572-reteu-7-0-ddumped-files-t3712521
Wipe all with twrp and flash all. After it you can get OTA's.
---------- Post added at 10:59 AM ---------- Previous post was at 10:57 AM ----------
Here is RR 5.8.5 working on N modem:
https://forum.xda-developers.com/mo...ial-resurrection-remix-v5-8-3-t3637204/page40 post #397
Wipe all with twrp, update twrp to 3.2 and you can flash it right now.
@
---------- Post added at 11:03 AM ---------- Previous post was at 10:59 AM ----------
@Husky34

oh thanx man! i've already seen that post but i wasn't sure that it can work for me. i have some question befor starting:
1) i need the new twrp 3.2 to flash resurrection-remix? because as i mention before i've already tried to flash it with twrp 3.1 and it doesen't work (the rom is the same that you linked page40 post #397 )
2) do i have to flash stock-xt-1572-reteu-7-0-ddumped-files before point 1)?
dzidexx said:
You missed very much.
Here is stock RetEu, before october update:
https://forum.xda-developers.com/moto-x-style/general/stock-xt-1572-reteu-7-0-ddumped-files-t3712521
Wipe all with twrp and flash all. After it you can get OTA's.
---------- Post added at 10:59 AM ---------- Previous post was at 10:57 AM ----------
Here is RR 5.8.5 working on N modem:
https://forum.xda-developers.com/mo...ial-resurrection-remix-v5-8-3-t3637204/page40 post #397
Wipe all with twrp, update twrp to 3.2 and you can flash it right now.
@
---------- Post added at 11:03 AM ---------- Previous post was at 10:59 AM ----------
@Husky34
Click to expand...
Click to collapse

Husky34 said:
oh thanx man! i've already seen that post but i wasn't sure that it can work for me. i have some question befor starting:
1) i need the new twrp 3.2 to flash resurrection-remix? because as i mention before i've already tried to flash it with twrp 3.1 and it doesen't work
2) do i have to flash stock-xt-1572-reteu-7-0-ddumped-files before point 1)?
Click to expand...
Click to collapse
1. I think so. 3.2.x will be needed for future builds.
1a. You flashed RR for MM modem.
2. No, but this is only way to get ota update.

"swearing in italian" it was a twrp bug.. after a backup restore if you hit restart the phone restart in recovery, you need to boot into bootloader and reboot system from there -.-
thanks to all of you guys!!

strange fact, now if i turn off the phone and again on i'm still on recovery, i have to reboot bootloader and system from there.
i think something is pointing at the recovery instead system..
edit: it seems that if you download an update and the install process doesen't go in place every time you restart the device it always try to re-flash it, that's why i'm always in recovery.. i foun a similar post with this solution but i think it need some changes before it will work on our device (but i don't have the knowledge to set it right :S )

Ota update didn't end.
I think you can try clear data & cache otaupdate app and disable it. Link2sd can help with it. @Husky34

dzidexx said:
Ota update didn't end.
I think you can try clear data & cache otaupdate app and disable it. Link2sd can help with it. @Husky34
Click to expand...
Click to collapse
just tried but wihout luck.. maybe i can wait someone make the flashable update but i don't think this fix the issue

Flash uploaded stock.

dzidexx said:
Flash uploaded stock.
Click to expand...
Click to collapse
actually i fixed the issue using this command
dd if=/dev/zero of=/dev/block/platform/f9824900.sdhci/by-name/misc
misc file running at the startup redirecting the boot in the recovery, put blank in the file let the system boot up normally

Husky34 said:
actually i fixed the issue using this command
dd if=/dev/zero of=/dev/block/platform/f9824900.sdhci/by-name/misc
misc file running at the startup redirecting the boot in the recovery, put blank in the file let the system boot up normally
Click to expand...
Click to collapse
thanks, this command just saved me. but misc file in my XT1575 is under
/dev/block/platform/0/f9824900.sdhci/by-name/misc
but now I can't check system update in the OS anymore, I think flash back factory recovery mine help. Do you know where to download stock 7.0 recovery for 1575?
Edit: found it for 1575 here.

pshadoww said:
thanks, this command just saved me. but misc file in my XT1575 is under
/dev/block/platform/0/f9824900.sdhci/by-name/misc
but now I can't check system update in the OS anymore, I think flash back factory recovery mine help. Do you know where to download stock 7.0 recovery for 1575?
Edit: found it for 1575 here.
Click to expand...
Click to collapse
you can also use link2sd to disable the update app so it doesn't bother you,
or wait untill someone create a zip of the update and flash it into recovery.

thanks, that worked for me as well.
File was located at /dev/block/platform/soc.0/f9824900.sdhci/by-name/misc

Related

MT7-TL 10 B511 Android Marshmallow TWRP Backup

This is a TWRP Backup of the Middle East Marshmallow OTA (B511) for TL 10 International Version:
Link:https://mega.nz/#F!i1QkjLrI
Decription key:!Rj6Iw_--xg8vABPi76NxeQ
Place the file within TWRP>BACKUPS folder in your SD card.
I did a factory reset via TWRP pior to backing-up and did not notice some of the apps (Most Google Apps and some stock Huawei apps like Compass, Mirror, etc.) went missing. So after restoring the back-up, you may restore those missing apps by doing the following:
1.) Download the Stock MM recovery
2.) Boot to fastboot mode then flash the stock recovery.
3.) After rebooting phone boot to stock recovery mode.
4.) On stock recovery choose "Wipe Data/Factory Reset". Once back on the phone will regain all lost apps/icons
Hi! Link mega crashed! ?
Enviado desde mi JAZZ
link not working please check before post
Link works.It must enter the decryption key: !Rj6Iw_--xg8vABPi76NxeQ
Hi is only for TL10?
tried to roll back from Marshmallow B511 but you fail, try my method here
http://forum.xda-developers.com/mate-7/general/tried-to-roll-b511-to-b326-fail-try-t3302479
blitzkriegger said:
This is a TWRP Backup of the Middle East Marshmallow OTA (B511) for TL 10 International Version:
Link:https://mega.nz/#F!i1QkjLrI
Decription key:!Rj6Iw_--xg8vABPi76NxeQ
Place the file within TWRP>BACKUPS folder in your SD card.
I did a factory reset via TWRP pior to backing-up and did not notice some of the apps (Most Google Apps and some stock Huawei apps like Compass, Mirror, etc.) went missing. So after restoring the back-up, you may restore those missing apps by doing the following:
1.) Download the Stock MM recovery
2.) Boot to fastboot mode then flash the stock recovery.
3.) After rebooting phone boot to stock recovery mode.
4.) On stock recovery choose "Wipe Data/Factory Reset". Once back on the phone will regain all lost apps/icons
Click to expand...
Click to collapse
Work very fine TL09
I tried several times on TL10 international version, but when rebooting system always got stucked on huawei logo screen. Even waited long periods with no effect.
Any hint?
pasil.pt said:
I tried several times on TL10 international version, but when rebooting system always got stucked on huawei logo screen. Even waited long periods with no effect.
Any hint?
Click to expand...
Click to collapse
did it work for you, because i tried it and had the same results, if it didn't, would you mind telling me what you did to make your phone work again please
---------- Post added at 02:34 PM ---------- Previous post was at 02:18 PM ----------
pasil.pt said:
I tried several times on TL10 international version, but when rebooting system always got stucked on huawei logo screen. Even waited long periods with no effect.
Any hint?
Click to expand...
Click to collapse
did it work for you, because i tried it and had the same results, if it didn't, would you mind telling me what you did to make your phone work again please
nozeback said:
did it work for you, because i tried it and had the same results, if it didn't, would you mind telling me what you did to make your phone work again please
---------- Post added at 02:34 PM ---------- Previous post was at 02:18 PM ----------
did it work for you, because i tried it and had the same results, if it didn't, would you mind telling me what you did to make your phone work again please
Click to expand...
Click to collapse
I can't remember well but i think I went into recovery (TWRP) to restore a backup
If you cannot go into twrp recovery either to restore a bckp or to flash another rom you need to go into the fastboot procedure, flashing img files from PC. But yoy can see this procedures on other threads
urgently need Stock MM recovery,plz
hi,thanks for the guide,I urgently need Stock MM recovery and I cant Find it,unfortunately my device has no recovery and most unfortunately it was on MM,After boot loader unlock, I flashed another recovery which seems to be incompatible and now device has no recovery,tried more than 10 recovery but none leave me a chance,please upload a stock MM recovery if possible.
Here
https://mega.nz/#!w15xjZxL!0-alMyU4RgsxQ6K6FjOPZna-piQLXODLE0QarKtdVCg
Send from ?
Looking for the stock browser apk from b331. Any chance someone has a link
ogre del said:
Looking for the stock browser apk from b331. Any chance someone has a link
Click to expand...
Click to collapse
Here https://mega.nz/#!Z9gjRJpR!iJmlBWIFRLhhDRIFu3--FoxkAj6Pc6wZCuajDZ7WKZw
Send from ?
New link thanks to @Blue.Ember
https://mega.nz/#!e1BmGBKY!xoGZ2s-AbUyg2khj98e-veul95_KU0esstyK4SmqtiM
Send from ?

Unable to boot into recovery after latest security patch, lost root.

after flashing the vendor image, i flashed the latest twrp. tried to reboot but unable to go into recovery and stuck in a black screen. Phone boots as normal but lost root. Phone can still be detected by pc, but when i go into bootloader it cant be detected and i flash back stock image. Any help will be appreciated.
Not entirely sure. I would start from scratch and follow this guide http://forum.xda-developers.com/nexus-6p/general/guides-how-to-guides-beginners-t3206928. I would jump to section 11 and go from there. I'm currently waiting for my cache to build after flashing latest stock image from google (MHC1). I followed section 9. Hopefully all goes well. I came from MMB29Q.
---------- Post added at 01:28 AM ---------- Previous post was at 01:09 AM ----------
well everything went as expected for me. That guide has never let me down. If you're using a toolkit to update I would abandon it. That guide is my bible when it comes to anything regarding modifying the 6p. I have seen multiple threads about TWRP not "sticking" or stuck at boot etc, etc. In order for you obtain root again you're going to need to flash TWRP, boot into it, and flash SU 2.68. There is a test version of TWRP 3.0 floating around that I used with no issues. I'll try to find the link and post it here. If not, maybe another user can post it if they have it handy.
Here
Thanks dude!
thx dude gonna give it a shot

Lineage OS (official nightly) installation problem

I was trying to flash official lineage os downloaded from official website through twrp but ended up with an error i can't figure out what to do of. i am uploading screenshot of twrp. help.
Are you coming from Cos 12.1 ?
Than you need to flash ZUI 2.5 ROM first or cm-13 ROM .
Because even if you flash nogout some problem like sim1 will stay always active and sim2 will be greyed out.
i am on zui 2.3.045
hardikkchavda said:
Are you coming from Cos 12.1 ?
Than you need to flash ZUI 2.5 ROM first or cm-13 ROM .
Because even if you flash nogout some problem like sim1 will stay always active and sim2 will be greyed out.
Click to expand...
Click to collapse
i am on zui 2.3.045 tell me full installation process if possible
Mikuzukz1 said:
I was trying to flash official lineage os downloaded from official website through twrp but ended up with an error i can't figure out what to do of. i am uploading screenshot of twrp. help.
Click to expand...
Click to collapse
Error 7 is caused by the custom recoveries. It occurs both on CWM and TWRP. Just wipe the whole phone and via ADB boot it to recovery (Command 'adb reboot recovery' -- without quotes.) Then copy the ROM to internal storage and now flash. It will work like a charm.
---------- Post added at 07:36 AM ---------- Previous post was at 07:29 AM ----------
hardikkchavda said:
Are you coming from Cos 12.1 ?
Than you need to flash ZUI 2.5 ROM first or cm-13 ROM .
Because even if you flash nogout some problem like sim1 will stay always active and sim2 will be greyed out.
Click to expand...
Click to collapse
Huh? How will that help? Why do need a 6.0 M ROM before you flash nougat? You can't dirty flash Lineage. It'll end in a boot loop. You have to wipe and flash. So how will the ROM that was installed before influence nougat flash?
+∆bhijith said:
Error 7 is caused by the custom recoveries. It occurs both on CWM and TWRP. Just wipe the whole phone and via ADB boot it to recovery (Command 'adb reboot recovery' -- without quotes.) Then copy the ROM to internal storage and now flash. It will work like a charm.
---------- Post added at 07:36 AM ---------- Previous post was at 07:29 AM ----------
Huh? How will that help? Why do need a 6.0 M ROM before you flash nougat? You can't dirty flash Lineage. It'll end in a boot loop. You have to wipe and flash. So how will the ROM that was installed before influence nougat flash?
Click to expand...
Click to collapse
Can i flash in fastboot or install Lineage os recovery?
Mikuzukz1 said:
Can i flash in fastboot or install Lineage os recovery?
Click to expand...
Click to collapse
Just flash in the normal way bro... Use TWRP > Install > then select the zip file.
+∆bhijith said:
Just flash in the normal way bro... Use TWRP > Install > then select the zip file.
Click to expand...
Click to collapse
it's showing error that way
Mikuzukz1 said:
it's showing error that way
Click to expand...
Click to collapse
Even now? Even after rebooting to recovery via ADB?
+∆bhijith said:
Even now? Even after rebooting to recovery via ADB?
Click to expand...
Click to collapse
I don't know how to boot via adb ijust wiped all partitions in twrp
got it working finally....installed it over cm13.0 and done
Mikuzukz1 said:
got it working finally....installed it over cm13.0 and done
Click to expand...
Click to collapse
Wonderful ! Good to go for any 7.x.x rom now...
---------- Post added at 03:30 PM ---------- Previous post was at 03:27 PM ----------
+∆bhijith said:
Error 7 is caused by the custom recoveries. It occurs both on CWM and TWRP. Just wipe the whole phone and via ADB boot it to recovery (Command 'adb reboot recovery' -- without quotes.) Then copy the ROM to internal storage and now flash. It will work like a charm.
---------- Post added at 07:36 AM ---------- Previous post was at 07:29 AM ----------
Huh? How will that help? Why do need a 6.0 M ROM before you flash nougat? You can't dirty flash Lineage. It'll end in a boot loop. You have to wipe and flash. So how will the ROM that was installed before influence nougat flash?
Click to expand...
Click to collapse
Because i faced same problems before and searched in XDA and that is the solution available right now.
Mikuzukz1 said:
I was trying to flash official lineage os downloaded from official website through twrp but ended up with an error i can't figure out what to do of. i am uploading screenshot of twrp. help.
Click to expand...
Click to collapse
I think file is not completely downloaded...
Once same happened when I checked I chose wrong file wwhich was half downloaded.. Check it
i'm facing the same problem. i don't know how to use adb boot.
isn't there any other way.
also i checked the file was completely downloaded
and i'm on zui 2.5
I also have problem when flash nuclearom from cm13. I have some zuk devices but got problem with 2
First, it has bootloop
I have to flash China ROM then it works
I can flash CM 13
But up to 14 or 7.x will have bootloop again
Pls help

A2017U Stuck on ZTE screen, cannot boot into system even after factory reset

So, while trying to follow the steps given to me to gain root access for data recovery, I stupidly swiped allow system modifications on the signed TWRP. The phone has been unable to boot into system ever since and only gets stuck on ZTE screen. I am able to boot into recovery, bootloader, FTM, and EDL but not system. This suggests that the system image has been corrupted somehow. I downloaded the B15 zip from ZTE's support page and tried to do update via SD card from stock recovery.
After selecting the zip file the phone screen showed the following (I tried with and without renaming the zip to update.zip):
supported api: 3
Install /sdcard/<"filename>".zip
finding update package, opening update package, verifying update package
E: footer is wrong
Update package verification took 1.0 s (result 1).
E: signature verification failed
Installation aborted
This entails that perhaps the official zip is faulty in some way. I chatted with ZTE support, he told me to wipe cache, try redownloading the zip file and retry without renaming, But no dice. Then he suggested a factory reset. I had read that for some others a factory reset had fixed the problem, so with some qualms, I went through with it. Lo and behold, even after 30 min the phone was still stuck on ZTE screen. ZTE support no longer has a B29 zip for downgrading and does not offer a B19 zip. So according to the support guy my last option is sending my phone in for repairs where they'll reformat the phone and reflash Stock ROM free of charge.
While that's all well and dandy, I am still desperately attempting data recovery (all efforts have been futile and I am well aware that I will likely be wholly unsuccessful). So, I was wondering if any of you guys had a backup of the fully stock system image, or had a zip file, or solution that would allow me to boot into system successfully without rooting or unlocking bootloader. A fully stock OS is preferred but am open to alternates such as DrakenFX's fastboot enabled EDL zip if there's absolutely no way to go back to fully stock OS. I am ok with downgrading and then updating later. Just don't want to get the phone reformatted. Thanks in advance.
TLDR: Phone stuck on ZTE screen; factory reset did not help; need to flash fully stock system image and maybe can boot successfully into system; if all else fails will probably submit warranty claim.
Install supersu or dm-verity to bypass the security checks.
tupurl said:
So, while trying to follow the steps given to me to gain root access for data recovery, I stupidly swiped allow system modifications on the signed TWRP. The phone has been unable to boot into system ever since and only gets stuck on ZTE screen. I am able to boot into recovery, bootloader, FTM, and EDL but not system. This suggests that the system image has been corrupted somehow. I downloaded the B15 zip from ZTE's support page and tried to do update via SD card from stock recovery.
After selecting the zip file the phone screen showed the following (I tried with and without renaming the zip to update.zip):
supported api: 3
Install /sdcard/<"filename>".zip
finding update package, opening update package, verifying update package
E: footer is wrong
Update package verification took 1.0 s (result 1).
E: signature verification failed
Installation aborted
This entails that perhaps the official zip is faulty in some way. I chatted with ZTE support, he told me to wipe cache, try redownloading the zip file and retry without renaming, But no dice. Then he suggested a factory reset. I had read that for some others a factory reset had fixed the problem, so with some qualms, I went through with it. Lo and behold, even after 30 min the phone was still stuck on ZTE screen. ZTE support no longer has a B29 zip for downgrading and does not offer a B19 zip. So according to the support guy my last option is sending my phone in for repairs where they'll reformat the phone and reflash Stock ROM free of charge.
While that's all well and dandy, I am still desperately attempting data recovery (all efforts have been futile and I am well aware that I will likely be wholly unsuccessful). So, I was wondering if any of you guys had a backup of the fully stock system image, or had a zip file, or solution that would allow me to boot into system successfully without rooting or unlocking bootloader. A fully stock OS is preferred but am open to alternates such as DrakenFX's fastboot enabled EDL zip if there's absolutely no way to go back to fully stock OS. I am ok with downgrading and then updating later. Just don't want to get the phone reformatted. Thanks in advance.
TLDR: Phone stuck on ZTE screen; factory reset did not help; need to flash fully stock system image and maybe can boot successfully into system; if all else fails will probably submit warranty claim.
Click to expand...
Click to collapse
I think this is B29 stock image DrakenFX has uploaded it on sharing website, give it a try.
https://www.androidfilehost.com/?fid=312968873555009511
romeoh said:
I think this is B29 stock image DrakenFX has uploaded it on sharing website, give it a try.
https://www.androidfilehost.com/?fid=312968873555009511
Click to expand...
Click to collapse
Thanks for the link!
Will this work via the update from sd card option on the stock recovery? Or would you recommend flashing from TWRP? Or via MiFlash in EDL mode?
gpz1100 said:
Install supersu or dm-verity to bypass the security checks.
Click to expand...
Click to collapse
Doesn't that require unlocked bootloader? I want to avoid voiding the warranty.
tupurl said:
Thanks for the link!
Will this work via the update from sd card option on the stock recovery? Or would you recommend flashing from TWRP? Or via MiFlash in EDL mode?
Click to expand...
Click to collapse
This is the zte official B29 package and the only way to used it from the stock recovery from the SD card. It won't work with twrp because it requires the stock recovery. You can also use this method and you don't have to have unlcked bootloader http://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514/page26
romeoh said:
This is the zte official B29 package and the only way to used it from the stock recovery from the SD card. It won't work with twrp because it requires the stock recovery. You can also use this method and you don't have to have unlcked bootloader http://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514/page26
Click to expand...
Click to collapse
So, I just now tried to apply the package you linked to (Draken FX stock Marshmallow) and it gave me the same errors :/
E: footer is wrong and E: signature verification failed. Should I try something else?
Enable OEM unlock and flash zte zip from external SD. Sometimes they zip it twice so check the file.
lafester said:
Enable OEM unlock and flash zte zip from external SD. Sometimes they zip it twice so check the file.
Click to expand...
Click to collapse
I can't boot into system. Is there a way to enable OEM unlock from recovery, EDL, or factory test mode?
Did you check the zip? You could always use miflash b15 full.
lafester said:
Did you check the zip? You could always use miflash b15 full.
Click to expand...
Click to collapse
I've been trying to use MiFlash to flash the B29 stock zip by DrakenFX that the romeroh linked to but I can't see my device in MiFlash :/. I know EDL works cuz the axon7tool is able to detect it and write or read recovery and boot properly. Ideas on how to get MiFlash to detect my phone?
tupurl said:
I've been trying to use MiFlash to flash the B29 stock zip by DrakenFX that the romeroh linked to but I can't see my device in MiFlash :/. I know EDL works cuz the axon7tool is able to detect it and write or read recovery and boot properly. Ideas on how to get MiFlash to detect my phone?
Click to expand...
Click to collapse
axon7tool uses different drivers. install the correct drivers for miflash.
tupurl said:
I've been trying to use MiFlash to flash the B29 stock zip by DrakenFX that the romeroh linked to but I can't see my device in MiFlash :/. I know EDL works cuz the axon7tool is able to detect it and write or read recovery and boot properly. Ideas on how to get MiFlash to detect my phone?
Click to expand...
Click to collapse
Ok, I think there was a little misunderstanding about the B29 link that I sent to you bro. That file can only be flashed in Stock recovery you can't flash it with MiFlash. If you want to use MiFlash the only version that's available to flash in EDL mode is Nougat B15. Just reread the OP of the the link I've sent to you before and If you didn't understand anything let us know there is always someone here will help you.
romeoh said:
Ok, I think there was a little misunderstanding about the B29 link that I sent to you bro. That file can only be flashed in Stock recovery you can't flash it with MiFlash. If you want to use MiFlash the only version that's available to flash in EDL mode is Nougat B15. Just reread the OP of the the link I've sent to you before and If you didn't understand anything let us know there is always someone here will help you.
Click to expand...
Click to collapse
I'm having sort of the same problem except I'm stuck on the bootloader unlocked screen and any rom I flash gets stuck on "patching system image unconditionally"
Fazedyrus said:
I'm having sort of the same problem except I'm stuck on the bootloader unlocked screen and any rom I flash gets stuck on "patching system image unconditionally"
Click to expand...
Click to collapse
Have you tried to use the EDL method?
https://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514
It should work on fixing this issue even if you are with Unlocked Bootloader, but you'll end up on Nougat B15 because this is the only full EDL mode package available.
romeoh said:
Have you tried to use the EDL method?
https://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514
It should work on fixing this issue even if you are with Unlocked Bootloader, but you'll end up on Nougat B15 because this is the only full EDL mode package available.
Click to expand...
Click to collapse
Did that, the flash is successful but I still have the same problem in that the system won't boot. Should I just relock and rma at this point?
---------- Post added at 09:30 PM ---------- Previous post was at 09:27 PM ----------
romeoh said:
Have you tried to use the EDL method?
https://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514
It should work on fixing this issue even if you are with Unlocked Bootloader, but you'll end up on Nougat B15 because this is the only full EDL mode package available.
Click to expand...
Click to collapse
Flashing supersu and dmverity zip doesn't work either
Fazedyrus said:
Did that, the flash is successful but I still have the same problem in that the system won't boot. Should I just relock and rma at this point?
---------- Post added at 09:30 PM ---------- Previous post was at 09:27 PM ----------
Flashing supersu and dmverity zip doesn't work either
Click to expand...
Click to collapse
You doing a full wipe before flashing? Flashing b15 full (no twrp)? Also try format data instead of wipe.
I've gone through this a few times and always manage to get booting.
lafester said:
You doing a full wipe before flashing? Flashing b15 full (no twrp)? Also try format data instead of wipe.
I've gone through this a few times and always manage to get booting.
Click to expand...
Click to collapse
I've done that several times already with no success. I think somehow my device just doesn't work
---------- Post added at 04:14 PM ---------- Previous post was at 04:12 PM ----------
lafester said:
You doing a full wipe before flashing? Flashing b15 full (no twrp)? Also try format data instead of wipe.
I've gone through this a few times and always manage to get booting.
Click to expand...
Click to collapse
also tried flashing DrakenFX's B29 Stock images but still can't boot into system
---------- Post added at 04:21 PM ---------- Previous post was at 04:14 PM ----------
lafester said:
You doing a full wipe before flashing? Flashing b15 full (no twrp)? Also try format data instead of wipe.
I've gone through this a few times and always manage to get booting.
Click to expand...
Click to collapse
I've tried many things over the past 3 days for over 10 hours so I think I'm gonna return this phone and just get a OP3T
---------- Post added at 04:45 PM ---------- Previous post was at 04:21 PM ----------
Fazedyrus said:
I've done that several times already with no success. I think somehow my device just doesn't work
---------- Post added at 04:14 PM ---------- Previous post was at 04:12 PM ----------
also tried flashing DrakenFX's B29 Stock images but still can't boot into system
---------- Post added at 04:21 PM ---------- Previous post was at 04:14 PM ----------
I've tried many things over the past 3 days for over 10 hours so I think I'm gonna return this phone and just get a OP3T
Click to expand...
Click to collapse
also, not being able to flash any rom with a working twrp makes it look like only I have this problem
---------- Post added at 05:32 PM ---------- Previous post was at 04:45 PM ----------
Fazedyrus said:
I've done that several times already with no success. I think somehow my device just doesn't work
---------- Post added at 04:14 PM ---------- Previous post was at 04:12 PM ----------
also tried flashing DrakenFX's B29 Stock images but still can't boot into system
---------- Post added at 04:21 PM ---------- Previous post was at 04:14 PM ----------
I've tried many things over the past 3 days for over 10 hours so I think I'm gonna return this phone and just get a OP3T
---------- Post added at 04:45 PM ---------- Previous post was at 04:21 PM ----------
also, not being able to flash any rom with a working twrp makes it look like only I have this problem
Click to expand...
Click to collapse
yep, everything is stock yet I am still not able to boot into system
lafester said:
Enable OEM unlock and flash zte zip from external SD. Sometimes they zip it twice so check the file.
Click to expand...
Click to collapse
tupurl said:
So, while trying to follow the steps given to me to gain root access for data recovery, I stupidly swiped allow system modifications on the signed TWRP. The phone has been unable to boot into system ever since and only gets stuck on ZTE screen. I am able to boot into recovery, bootloader, FTM, and EDL but not system. This suggests that the system image has been corrupted somehow. I downloaded the B15 zip from ZTE's support page and tried to do update via SD card from stock recovery.
After selecting the zip file the phone screen showed the following (I tried with and without renaming the zip to update.zip):
supported api: 3
Install /sdcard/<"filename>".zip
finding update package, opening update package, verifying update package
E: footer is wrong
Update package verification took 1.0 s (result 1).
E: signature verification failed
Installation aborted
This entails that perhaps the official zip is faulty in some way. I chatted with ZTE support, he told me to wipe cache, try redownloading the zip file and retry without renaming, But no dice. Then he suggested a factory reset. I had read that for some others a factory reset had fixed the problem, so with some qualms, I went through with it. Lo and behold, even after 30 min the phone was still stuck on ZTE screen. ZTE support no longer has a B29 zip for downgrading and does not offer a B19 zip. So according to the support guy my last option is sending my phone in for repairs where they'll reformat the phone and reflash Stock ROM free of charge.
While that's all well and dandy, I am still desperately attempting data recovery (all efforts have been futile and I am well aware that I will likely be wholly unsuccessful). So, I was wondering if any of you guys had a backup of the fully stock system image, or had a zip file, or solution that would allow me to boot into system successfully without rooting or unlocking bootloader. A fully stock OS is preferred but am open to alternates such as DrakenFX's fastboot enabled EDL zip if there's absolutely no way to go back to fully stock OS. I am ok with downgrading and then updating later. Just don't want to get the phone reformatted. Thanks in advance.
TLDR: Phone stuck on ZTE screen; factory reset did not help; need to flash fully stock system image and maybe can boot successfully into system; if all else fails will probably submit warranty claim.
Click to expand...
Click to collapse
lafester is correct, the B15 file from downloaded from ZTE is zipped twice. There is an actual update.zip inside a folder inside the "America A2017U SD card software package(A2017UV1.1.0B15)SD_W" zip. When I bricked my phone, I extracted the update.zip and I was able to flash it from the SD with the stock recovery. Hope that helps.
Howie Dub said:
lafester is correct, the B15 file from downloaded from ZTE is zipped twice. There is an actual update.zip inside a folder inside the "America A2017U SD card software package(A2017UV1.1.0B15)SD_W" zip. When I bricked my phone, I extracted the update.zip and I was able to flash it from the SD with the stock recovery. Hope that helps.
Click to expand...
Click to collapse
where can I find this zip

OTA update on unlocked and rooted device

I have a well working Note 7 with unlocked and rooted 10.3.5.0 Global PFGEUXM (TWRP recovery and magisk).
Today I got the OTA notification to update ROM to 10.3.6.0.
What I will lose if I update?
What's the best way to proceed?
Thank you
Nothing will be lost from a regular OTA Just check around for any bugs or problems that other people are having if any? And update if you like.
rockerduck said:
I have a well working Note 7 with unlocked and rooted 10.3.5.0 Global PFGEUXM (TWRP recovery and magisk).
Today I got the OTA notification to update ROM to 10.3.6.0.
What I will lose if I update?
What's the best way to proceed?
Thank you
Click to expand...
Click to collapse
You have to download the full rom then go to twrp and wipe cache and dalvik flash the rom and magisk without reboot to system. After the flash of magisk you can reboot to the system. If you don't flash magisk before rebooting MIUI overwrite the twrp with the stock recovery and you have to reinstall twrp with fastboot
---------- Post added at 02:14 PM ---------- Previous post was at 02:12 PM ----------
If you get a compatibility error when flashing the rom just delete from the rom zip the file compatibility.zip
darhma said:
You have to download the full rom then go to twrp and wipe cache and dalvik flash the rom and magisk without reboot to system. After the flash of magisk you can reboot to the system. If you don't flash magisk before rebooting MIUI overwrite the twrp with the stock recovery and you have to reinstall twrp with fastboot
---------- Post added at 02:14 PM ---------- Previous post was at 02:12 PM ----------
If you get a compatibility error when flashing the rom just delete from the rom zip the file compatibility.zip
Click to expand...
Click to collapse
Thank you very much darhma.
Should I reflash Disable_Dm-Verity before magisk?
rockerduck said:
Thank you very much darhma.
Should I reflash Disable_Dm-Verity before magisk?
Click to expand...
Click to collapse
You're welcome. I don't think it's needed the disable_dm-verity (but also i don't think that's a bad thing if you reflash it). If you want to thanks somebody in xda forum just press the thanks button (the ok button).
Hi!
I am new here so please don't be angry for my next questions
I just want root my Redmi Note 7 and keep OTP updates.
I read so many threads and this is my conclusion:
First I must apply for unlocking bootloader. Then flash TWRP recovery from here. After this flash Magisk through TWRP and that is it!
When phone notifies me that there is a new software update, I must download recovery rom from here, put it in internal memory, flash it and flash immediately Magisk again (flashing Magisk is mandatory after every software update to keep root).
Can anybody confirm that this is right way?
Thank You in advance.
wheelnut said:
Hi!
I am new here so please don't be angry for my next questions
I just want root my Redmi Note 7 and keep OTP updates.
I read so many threads and this is my conclusion:
First I must apply for unlocking bootloader. Then flash TWRP recovery from here. After this flash Magisk through TWRP and that is it!
When phone notifies me that there is a new software update, I must download recovery rom from here, put it in internal memory, flash it and flash immediately Magisk again (flashing Magisk is mandatory after every software update to keep root).
Can anybody confirm that this is right way?
Thank You in advance.
Click to expand...
Click to collapse
Yes that's the right way.
---------- Post added at 01:34 PM ---------- Previous post was at 01:26 PM ----------
Another thing: if you get a compatibility error when flashing the rom just delete from the rom zip the file compatibility.zip
darhma said:
Yes that's the right way.
---------- Post added at 01:34 PM ---------- Previous post was at 01:26 PM ----------
Another thing: if you get a compatibility error when flashing the rom just delete from the rom zip the file compatibility.zip
Click to expand...
Click to collapse
Can I do that in TWRP or I must unpack rom on computer and pack it as zip again?
wheelnut said:
Can I do that in TWRP or I must unpack rom on computer and pack it as zip again?
Click to expand...
Click to collapse
I think that you can do that from twrp but i'm not 100% sure. From computer you don't need to unpack and repack, just open the zip with 7zip or unrar (i'm on linux and don't know which program you use for zip files) and delete the file
darhma said:
I think that you can do that from twrp but i'm not 100% sure. From computer you don't need to unpack and repack, just open the zip with 7zip or unrar (i'm on linux and don't know which program you use for zip files) and delete the file
Click to expand...
Click to collapse
I'm using Windows and WinRAR. Will try after I download recovery rom (my dl speed is ****ty so it wont be soon)
I'm getting Error: 7 and am unable to update through TWRP on Redmi Note 7. Anyone else facing this?
thelastprime said:
I'm getting Error: 7 and am unable to update through TWRP on Redmi Note 7. Anyone else facing this?
Click to expand...
Click to collapse
Are you sure you downloaded the right rom? Error 7 is a mismatch of the firmware
Just come to say that everything went fine.
I didn't need to wait for unlock bootloader. I bought phone 2 weeks ago and using it normally and when I start unlock procedure it unlock without waiting time (I saw that someone must wait 720 hours!!).
I flash twrp and magisk (I had fingerprint lock so after flashing I did data erase) and now I have rooted phone
So, I have a my Redmi Note 7 keeps telling me that there is a new update which is V10.3.10.0.PFGMIXM
I didn't want to install it since I was happy with my phone. But now the notification is not going away and it is always there. So I tried to install it from OTA but since my phone is unlocked and has TWRP on it, the update can't be installed.
My questions are:
- Should I download the rom and flash it through TWRP?
- How should I flash it without being have to make a factory reset? Is it posible not to loose any data? And if so, is it bad to flash it just like that?
- There is a kernel which is called EVIRA that I want to flash, too. So the order should be:
Rom + Kernel + Minsk, is that correct?
Thanks in advance.
EDIT: There are 2 versions of the new rom:
Recovery Rom and Fastboor Rom.
https://c.mi.com/thread-2432115-1-0.html
What is the difference? Which one should I download?
kaplanfa said:
So, I have a my Redmi Note 7 keeps telling me that there is a new update which is V10.3.10.0.PFGMIXM
I didn't want to install it since I was happy with my phone. But now the notification is not going away and it is always there. So I tried to install it from OTA but since my phone is unlocked and has TWRP on it, the update can't be installed.
My questions are:
- Should I download the rom and flash it through TWRP?
- How should I flash it without being have to make a factory reset? Is it posible not to loose any data? And if so, is it bad to flash it just like that?
- There is a kernel which is called EVIRA that I want to flash, too. So the order should be:
Rom + Kernel + Minsk, is that correct?
Thanks in advance.
EDIT: There are 2 versions of the new rom:
Recovery Rom and Fastboor Rom.
https://c.mi.com/thread-2432115-1-0.html
What is the difference? Which one should I download?
Click to expand...
Click to collapse
1) download the full recovery rom
2) reboot to twrp
3) wipe dalvik art/cache and cache
4) flash the rom, the kernel and magisk in this order. Don't reboot to system until you have flashed magisk
5) reboot to system
6) enjoy
If you get a compatibility error when flashing the rom just delete the file compatibility.zip from the rom zip
Is updating ota with full recovery rom via twrp erase internal data or installed app?
darhma said:
1) download the full recovery rom
2) reboot to twrp
3) wipe dalvik art/cache and cache
4) flash the rom, the kernel and magisk in this order. Don't reboot to system until you have flashed magisk
5) reboot to system
6) enjoy
If you get a compatibility error when flashing the rom just delete the file compatibility.zip from the rom zip
Click to expand...
Click to collapse
Is installed app or data lost?
m.nav7854 said:
Is installed app or data lost?
Click to expand...
Click to collapse
If you do an update there should be no data loss however it is always recommended to have a backup of your data

Categories

Resources