Database Users

Newbie guide for installing a Custom ROM in SGP312 Sony Xperia Tablet Z

The objective of this post is to explain how to currently install a custom ROM in our device. (for total newbies like me, you can also refer -among others- to my previous post). I give the general procedure which wipes everything in your device, but you can check various precious posts in xda that variate this procedure.
The codename for our device is "pollux_windy", which is the Wifi-only version. The LTE version (I should probably get the LTE!) is "pollux" and I suppose the general procedure (with the corresponding firmwares to your specific device) will work for any Xperia device. You can also get the general idea from this post.
As a general rule of thumb do not forget after/before every firmware flashing to:
Enable developer mode (explained here)
Enable the USB Debugging mode (explained here)
Trust installation from unknown sources (explained here)
Steps.
A. Unlock the bootloader.
You can refer here and then check that it is successfully unlocked with these steps (taken from here ):
Open the Contacts app.
Click the menu button.
Click Settings.
Long press (for about 5 seconds) somewhere in the empty space just above status bar, as indicated by the red frame in the screenshot below, and then release your finger. A button named Enter service code will then appear in the same area (this may take a few tries).
Click Enter service code. A dialler will appear.
Dial *#*#7378423#*#* . Then go to -> "Service Info" -> "Configuration". If there is:
Bootloader unlock allowed - Yes << this means that your Bootloader is Locked
Bootloader Unlocked - Yes << this means that your bootloader is unlocked
B. Flash a firmware in which you will root the device
Download/install FlashTool.
Download and place to the FlashTool's folder "firmwares" the firmware "SGP312_10.5.A.0.230_VMo UK_IE.ftf". More information here . In sort, download and extract http://d-h.st/MrI and http://d-h.st/ULc
Open FlashTool and connect the powered-off device (USB cable) in Flashmode, holding the Volume Down button while you plugin the usb cable. The FlashTool should say that it is connected in Flashmode. Then flash the 10.5.A.0.230 firmware in it.
C. Gain root to the new firmware
Open the device, complete the setup wizard and connect to a wireless network. You do not have to setup the Google Account since you can download every application googling the respective APK files, but Google Play is easier to use.
Get (click λ) the towelroot APK, install it and run it (click "make it rain"). You should have root, which you can check with a Root Cheker like this one.
Download/Install SuperSU APK (this is actively developed, while SuperUser is abandoned at the moment) as described here.
D. Install a Recovery to easily flash new ROMs
NUT has done excellent work with XZDualRecovery.Follow the instructions for installing it in his thread. In short:
Download the installer, run it and follow its instructions.
Select SuperSU and of course grant access to your computer from your tablet (watch the tablet screen).
E. Download a Custom ROM and Google Apps
I had problems with Cyanogenmod (versions 11 and 12) that I cannot explain. I had no GPS and no media sound from the speakers, but I did have "notifications" sound! I could listen to "media" sounds using headphones, though. So I tried the nightly OmniROM which seems very stable and fast at the moment, with no sound problems and also has a working GPS! You can get it directly from their site (the NIGHTLY I downloaded is omni-4.4.4-20150223-pollux_windy-NIGHTLY.zip which runs just fine). Somewhere I read that PacMan ROM - also works perfectly but I have not tested it yet.
I had device recognition problems from the Recoveries ("Status 7 Error") that I think dear NUT will solve promptly. What I did to solve them is
Upack the ROM zip.
Remove the first line (from assert(...); till the column) of META_INF/com/google/android/updater-script and save the file.
repack the ROM to a zip.
Then copy this zip to your external SD card. If you need google apps (you probably do, to use Google Play instead of other applications like Aptoide), you will also need to download and place to your external SD card the corresponding google apps from here - (I found it in this post - which also explains the different gapps versions)
F. Install the Custom ROM
So now that both the ROM and (optionally) gapps are in the device's SD card:
Enter the Recovery while repeatedly pressing Volume Up or Down while the device boots.
Wipe everything (except the external SD card, obviously --- if you delete the zip files by mistake you must begin again from step B. using the FlashTool to flash the *.230* ftf).
Reboot and setup/enjoy your new ROM.
It seemed that with OmniROM I had lost root access so I had to reinstall SuperSU. I did this by downloading the flashable/installable zip - and flashing/installing it through the recovery.
In the end a did a full backup with the TWRP recovery and one with Titanium backup

Magnus_E said:
The objective of this post is to explain how to currently install a custom ROM in our device. (for total newbies like me, you can also refer -among others- to my previous post). I give the general procedure which wipes everything in your device, but you can check various precious posts in xda that variate this procedure.
Click to expand...
Click to collapse
For installing customs (CM/AOSP/GPe based ROM's), you don't need to install .230 firmware, furthermore you don't need root (except for backup TA procedure), furthermore you don't need XZDualRecovery (cause it works only for Stock and Custom STOCK based rom's - see this post).
So you you only need to flash kernel via fastboot, and then enter recovery (integrated in kernel), and install .zip with custom, SuperSU and Gapps from there.

hello i was following this guide but im stuck on status 7 error, i tried deleting assert but the twrp recovery dont get any answer to "getprop ro.product.device" and it just doesnt proceed...
and Rootk1t i cant find any kernels flashable via fastboot or flashtool can you point one to me? all of the kernels i see are in '.zip's .... i want to have android 6.0 so i think i should have black kernel but how?

bluealef said:
hello i was following this guide but im stuck on status 7 error, i tried deleting assert but the twrp recovery dont get any answer to "getprop ro.product.device" and it just doesnt proceed...
and Rootk1t i cant find any kernels flashable via fastboot or flashtool can you point one to me? all of the kernels i see are in '.zip's .... i want to have android 6.0 so i think i should have black kernel but how?
Click to expand...
Click to collapse
.zips are installed through recovery, .ftf through flashtool.
6.0.1 ROM you can find here.

Stock recovery extraced from BTV-W09C233B019 ROM - untested

Hi M3 users,
I'm a long time lurker and reader on XDA. Now it's time to give something back or at least participate
Following my recent M3 purchase a dugg a bit deeper into this topic and tried to get us the stock recovery for our devices.
I'm not really a dev. I just used the information I found here and in the russian forum where greatslon (thank you guy) is posting his work.
If you find an error in the process please let me know. The files have not been tested in any way. I have no idea if this would even work (encryption and so on).
So I managed to extract the recovery.img file from the chinese rom. This method will also work for the LTE variant.
Maybe @greatslon or @somboons can share their view on the topic or maybe @somboons can even use it in his tool.
Resources
http://4pda.ru/forum/index.php?showtopic=780572&st=120
http://forum.xda-developers.com/showthread.php?t=2433454
http://forum.xda-developers.com/tools/general/huawei-firmware-finder-team-mt-t3469146
https://play.google.com/store/apps/details?id=com.teammt.gmanrainy.huaweifirmwarefinder
Tools used
Huawei Firmware Finder (Team MT)
Huawei Update Extractor
Download
M3_BTV-W09C233B019_recovery.zip
Process
1. Start firmware finder (did use the android version)
2. Change device to BTV-W09C233
3. Downloaded the firmware B019 for BTV-W09C233 (no firmware for other variants present ATM)
4. Extracted and copied update.app to SD card
5. copy to PC
6. Extract recovery.img and recovery2.img using Huawei Update Extractor
Best regards,
Benjamin

Don't quite understand what's this for. First of all, recovery should be the same version as your ROM. I don't know if their mismatch will immediately lead to some malfunction, but some people on 4pda said they should match. Second - stock recovery's functions are limited to factory reset (wiping data, cache, etc.) and installing OTA updates. Without changing OEMINFO (and it's still unconfirmed), you won't be able to install any OTA except those, intented for your model and region, so again there's no need to install a higher version of recovery than your ROM is. But anyway, thank you for the extraction instruction.
P.S. I think there's no need to flash both recovery and recovery2. Recovery2 can be successfully replaced with TWRP and this combination is really great, cause you can launch TWRP by holding Volume Up button only.
And the only reason why you should keep recovery original is that it doesn't really wipe /data - it also creates some files there like custom.bin, containing your regional settings.

Hi Slavon,
Thanks for your highly appreciated comment. @somboons was looking for a stock recovery so I thought this might help.
Your given information are really helpful. I did not know that you could flash TWRP in recovery2 and replace erecovery Handy information.
I'm pretty new to the Huawei structure so always glad to learn something.
EDIT
A lot of good information can be found here: http://forum.xda-developers.com/honor-7/general/dual-recovery-honor-7-t3308398
Thank you very much,
sselpeelsxx

Giving Back
Benjamin,
I've also been a long time XDA lurker. Most of the devices I have owned were mainstream and thus already had a very active XDA developer community; Even if root had yet to be achieved, there would be hundreds of messages on the topic.
It seems the Mediapad M3 is just getting started. I am a developer of over 20 years, but very little android experience. However, I have recently spent a considerable amount of time (about 50-100 hours) working with the low level ADB protocol source code. And I have rooted and flashed no less than 50 devices, everything from cell phones to Android TV devices to routers.
I'm going to take this device on as my first real dev effort in this arena.
I have a few goals:
1. Get working backups for people that soft-brick or need to revert (including myself).
2. Recompile TWRP for the M3 to confirm greatslon's work, and better understand the process.
3. Release a stock rom that's pre-rooted and cleaned up (not that there was a lot of bloat on my device).
4. Release a custom rom that's not MIUI (perhaps based of CyanogenMod).
Since I have virtually no experience, I am sure these goals are quite lofty and will take some time. But hey, you got to have a plan, and I don't have anything else to work on right now.
Let me know if you want to work on anything together, or if you need any help with anything development related.
- 0D0A

Hey hey 0D0A,
I totally agree with you regarding the backups, I think once the first OTA update is pushed for the EU and US devices we have a good and safe way to go back.
Especially the US owners are struggling with greatslons TWRP version, that's the first thing we should tackle after the backup topic is cleared
I will contact you regarding possible work
Best regards,
Benjamin

can flash twrp via fastboot but get error saying and no recovery
hi, first thanks greatslon for doing the work on m3.
i seem to have succeeded in getting stuck and can't get it to boot into your custom twrp. adb on linux was working fine, but no longer. ditto for fastboot just get "waiting for devices" now. i switched to win10 and installed the hisuite app so i can use fastboot but still no adb. so i have tried to flash recovery and recovery2 but when i try to boot recovery i get error "Func NO: 11 (recovery image) ERROR NO: 2 (load failed)."
i then downloaded your custom rom and tried to flash the boot for that still no luck. i can't use adb so i am not sure how to just flash the custom rom with fastboot without being able to get into any recovery.
i did have this all rooted and working with your twrp but kept having issues with dpi and there was an ota update (b003) which wouldn't apply. so i tried to restore backup and it wen't south from there. basically now can't do much other than see the unlock "can't be trusted" page and bootloader.
any suggestions?

Desperately need stock recovery img, not sure exactly what when wrong, but it is stuck in a horrible boot loop. Tried Benjamin's recovery files and they seem to remove twrp and put it somewhat back to normal, but can only access the emui recovery and that fails to load the files. Put twrp back and tried greatslon's ROMs, they load but goes back to boot loop. Wipe and format everything, install my original backup through twrp recovery, it says it works, but again, back to boot loop... at this point I think I'm dead... any ideas, any word on the official recovery img? anything? Help!!

What device do you have? And what version were you on?

sselpeelsxx said:
What device do you have? And what version were you on?
Click to expand...
Click to collapse
I have the M3, BTV-W09, not sure what version, MM6.0 EMUI 4.1

Anyone have any other ideas on horrendous boot loop?

sselpeelsxx said:
Hey hey 0D0A,
I totally agree with you regarding the backups, I think once the first OTA update is pushed for the EU and US devices we have a good and safe way to go back.
Especially the US owners are struggling with greatslons TWRP version, that's the first thing we should tackle after the backup topic is cleared
I will contact you regarding possible work
Best regards,
Benjamin
Click to expand...
Click to collapse
Hello, I am unlocked, TWRPed, and rooted, but am trying to reverse all of that. My build number is BTV-W09C128B002. Is it safe to download the stock recovery from the OP for my device? Or do I really need the C128 version?

Hello and sorry for the late response, you would need the matching version for your C128 device.
I may be able to extract recovery from an update, I have to look into this tomorrow.
Regards

sselpeelsxx said:
Hello and sorry for the late response, you would need the matching version for your C128 device.
I may be able to extract recovery from an update, I have to look into this tomorrow.
Regards
Click to expand...
Click to collapse
Thanks! I have been able to use the Huawei Extractor to extract a recovery.img from OTA updates, but have been afraid to try flashing it. It has been recommended to hold off on trying that since that recovery.img is from an OTA and not a FULL update. Any thoughts?

Guide to flash Nougat if you face bootloops when upgrading

Hey guys!
This is just a simple post for you guys who want to make the jump to Nougat on the Snapdragon version of the Redmi Note 3, but face issues like bootloop or soft brick .
I tried many times to flash to Nougat and failed, so I thought I would document my experience for anyone who needs it.
The main problem I faced was an outdated bootloader.
Here, I have detailed the steps I took to flash Nougat successfully on my phone.
This does assume that you do have some experience and knowledge about the world of custom ROMs.
- disclaimer -
I am not responsible for any damage you may cause as a result of following this guide.
I am not affliated with any of the authors that wrote the guides that I will link in this guide.
The links are there purely for reference, and if you wrote one of the posts that I have linked in this guide, please message me to have your name at the bottom of this post.
- disclaimer end -
Here are a few things to note.
1) The version of MIUI you were on when you unlocked your bootloader.
2) Whether or not you have uploaded your bootloader
3) Whether you unlocked your bootloader officially
4) Whether you have permission to unlock the bootloader from XiaoMi.
5) Download and install the latest version of MiFlash
6) Download and install ADB and Fastboot on your PC
7) Boot into download mode to check if your PC recognises your phone. If not, reinstall the appropriate drivers.
A few websites you might want to refer to :
A MIUI forum page which teaches you how to flash/unbrick your Redmi Note 3.
http://en.miui.com/thread-235865-1-1.html
A MIUI forum page that teaches you how to repair your IMEI if it gets corrupted
http://en.miui.com/thread-245598-1-1.html
A guide to the XiaoMi deep flash cable as a kind of last resort(This is essentially Xiaomi's version of Samsung's USB jig; to force your device into download mode)
http://forum.xda-developers.com/redmi-note-3/how-to/guide-how-to-flash-hard-bricked-redmi-t3490055
First, you may want to do a few things.
1) Check and double check your device codename (Kenzo for Redmi note 3 Pro, Kate for Redmi Note 3 SE)
2) Download the latest Global Developer ROM (There are .zip and .tar versions, for this guide we will be using the latter. I get my ROMs from here : http://en.miui.com/a-234.html )
After downloading it, decompress it until you see the file extension .tgz, then unzip it once more. At the end you should have one folder which contains some files and a folder called images.
3) Research and download the ROM and custom kernel of your choice
4) Check up and research anything you are unfamiliar with ( This is a great place to start : http://forum.xda-developers.com/redmi-note-3/how-to/guide-redmi-note-3-available-twrps-t3406708 )
So, to flash the ROM, you can follow these steps. Do note that these steps worked for me at the time of writing and may not necessarily work for you.
1) Backup your stuff (Pictures, chats, contacts, etc.)
2) Go to developer options and check enable OEM unlock and ADB.
3) Reboot into bootloader.(adb reboot bootloader / vol- + pwr from power off state)
4) Use MiFlash to flash the global developer ROM you downloaded.
5) Use the MiUnlock tool to unlock your device.
6) Reboot to MIUI. (If you don't, you might face problems with TWRP demanding for password)
7) Boot to download mode again.
8) Install TWRP recovery.
9) You can now make a nandroid backup. Also make a backup of your EFS partition and keep it somewhere safe.
This assumes that you flashed the latest global developer ROM.
10) You can now flash the ROM and GApps.
11) If you want to install a custom kernel, finish setting up the phone before flashing one.
12) You can install Viper4Arise now if you want.

ZTE Blade A2 Plus Rooting( SuperSU or Magisk),Recovery & Flashing Stock Rom

Hi there, good to see you.
After struggling to find any helpful information about rooting ZTE Blade A2 plus, I finally was able to root>soft brick>hard brick>stock flash>repeat this beautiful device. So thought to share it here so that it becomes helpful for someone in need.
Device Information: https://forum.xda-developers.com/ge...te-blade-a2-plus-5-5-fhd-mt6750t-3gb-t3480759
Prerequisite: Winrar Latest version, VCOM and device drivers (MT67xx), General intelligence to download the attachments and to arrange everything in order and you're good to go
Step 1: Install custom recovery (We'll install TWRP)
a} Download recovery and preloader
b} Download Scatter file
c} Download SP Flash tools
d} Only tick recovery and preloader and select the downloaded files and flash it
e} When the process finishes and SP flash tools displays done, remove the phone and press "Vol Up+Power" to boot into recovery. It may ask you to make /system writable if you want swipe as indicated
f} Done enjoy
Note: Take this opportuniy to first of all backup your stock rom using TWRP and save it elsewhere.
Step 2: Rooting (With Magisk Or Super SU)
a} Download Magisk or Super SU flashable zip as per your need
Note: Magisk gives most of the Super SU features and doesn't trips google security net so you are able to use banking apps while rooted with magisk
b} Place downloaded zip in your sd card
c} Boot into TWRP recovery and flash the said zip
d} Done enjoy
Step 3: Flashing stock rom (Only russian version as of now)-Language is english bloatwares are Russian
a} Download Stock Rom from https://yadi.sk/d/RZLBrKKv3LxejN
Note: It contains PC Flashable stock rom along with scatter files and NVRAM backups so it'll help if you lose IMEI during the process, it is advisable to keep this offline as backup in case links stops working.
b} Flash the downloaded stock rom with SP flash tools
Note: This stock rom doesn't support VOLTE so i advice you to first take a full backup of your initial rom after installing TWRP, also please share that backup here as well so as i could add it to this thread to make it helpful for someone who has already lost VOLTE inclusing me
Conclusion: I'll be very happy if this information proves useful to you in any manner and also request you to must share your backup for me to get VOLTE back.
Thank You

MIUI 9 For A610 Plus
Preview:
Many many thanks Alfonso for making this vary valuable post . I think A2 Plus and A610 Plus are almost same , so kindly check this ROM me and may solve your volte problem
ww.getdroidtips.com/miui-9-zte-blade-a610-plus/[/url]

Rajevpmavoor said:
Preview:
Many many thanks Alfonso for making this vary valuable post . I think A2 Plus and A610 Plus are almost same , so kindly check this ROM me and may solve your volte problem
ww.getdroidtips.com/miui-9-zte-blade-a610-plus/[/url]
Click to expand...
Click to collapse
Although the rom is bugless but, unfortunately VOLTE didn't work.

MIUI 9 For A610 Plus
Did you flash this new MIUI 9 ROM , I think it has volte and it is in Android M.

Alfonso Osnofla said:
Although the rom is bugless but, unfortunately VOLTE didn't work.
Click to expand...
Click to collapse
does it boot into meta mode on pressing volume down+power button??( bcoz my fone boots into meta mode on doing so)
and how to go into bootloader?
while using sp flash tool i power off the fone and then connect it to sp flash tool via usb cable ...fone gets detected and but download for twrp doesnt occur ..it says PMT changed for the rom, select format all+ download ....
but i didnt do format all coz i dont have flashable stock rom...

I lost my IMEI after flash ROM, not able to retrieve IMEI

Issue in camera & Finger Lock
Alfonso Osnofla said:
Although the rom is bugless but, unfortunately VOLTE didn't work.
Click to expand...
Click to collapse
I have checked both ROM, Miui ROM camera is look like .02MB, No VOLTE, Finger Print lock is not working

Thanks. I have messed up anyway...
Anybody have a complete Readback (Using SP-Flash Tools) copy of (volte) rom?
I lost Imei, From the given NVram.bin, Could not edit Imei using BPGL.... pull as Maui Meta and SN writer can not do this with present update.
I need to revert back. please help with ROM copy and NVRAM Edit.

Alfonso Osnofla said:
Hi there, good to see you.
After struggling to find any helpful information about rooting ZTE Blade A2 plus, I finally was able to root>soft brick>hard brick>stock flash>repeat this beautiful device. So thought to share it here so that it becomes helpful for someone in need.
Device Information: https://forum.xda-developers.com/ge...te-blade-a2-plus-5-5-fhd-mt6750t-3gb-t3480759
Prerequisite: Winrar Latest version, VCOM and device drivers (MT67xx), General intelligence to download the attachments and to arrange everything in order and you're good to go
Step 1: Install custom recovery (We'll install TWRP)
a} Download recovery and preloader
b} Download Scatter file
c} Download SP Flash tools
d} Only tick recovery and preloader and select the downloaded files and flash it
e} When the process finishes and SP flash tools displays done, remove the phone and press "Vol Up+Power" to boot into recovery. It may ask you to make /system writable if you want swipe as indicated
f} Done enjoy
Note: Take this opportuniy to first of all backup your stock rom using TWRP and save it elsewhere.
Step 2: Rooting (With Magisk Or Super SU)
a} Download Magisk or Super SU flashable zip as per your need
Note: Magisk gives most of the Super SU features and doesn't trips google security net so you are able to use banking apps while rooted with magisk
b} Place downloaded zip in your sd card
c} Boot into TWRP recovery and flash the said zip
d} Done enjoy
Step 3: Flashing stock rom (Only russian version as of now)-Language is english bloatwares are Russian
a} Download Stock Rom from https://yadi.sk/d/RZLBrKKv3LxejN
Note: It contains PC Flashable stock rom along with scatter files and NVRAM backups so it'll help if you lose IMEI during the process, it is advisable to keep this offline as backup in case links stops working.
b} Flash the downloaded stock rom with SP flash tools
Note: This stock rom doesn't support VOLTE so i advice you to first take a full backup of your initial rom after installing TWRP, also please share that backup here as well so as i could add it to this thread to make it helpful for someone who has already lost VOLTE inclusing me
Conclusion: I'll be very happy if this information proves useful to you in any manner and also request you to must share your backup for me to get VOLTE back.
Thank You
Click to expand...
Click to collapse
Just try http://www.ztedevice.com/support/detail?id=FE22BEF5C33D4A17BCDA20AAE2631951 ( http://download.ztedevice.com/support/product/569/201802111051594/sd/20180211105554767.zip )
sd card update using twrp.
But first remove the first line from update script file located inside the zip.
Just reply.

Need MIUI rom
Heyy plz gime me teh rom for zte blade A2 plus i really need a miui rom for zte blade A2 plus...

Help I'm confused.
Reading the comments i got to know that many people lost their IMEI and VOLTE , I want to root the device So can anyone tell me when does this problem occur (loosing volte and imei) during rooting or while flashing a custom rom?

kingksath said:
I lost my IMEI after flash ROM, not able to retrieve IMEI
Click to expand...
Click to collapse
Did you loose your IMEI on rooting or while flashing any custom Rom?

http://www.mediafire.com/file/6768c1x7dqyd818/update.zip
version 4 sd card update

vasilemk said:
http://www.mediafire.com/file/6768c1x7dqyd818/update.zip
version 4 sd card update
Click to expand...
Click to collapse
What is it for?
Is it for volte?

vasilemk said:
http://www.mediafire.com/file/6768c1x7dqyd818/update.zip
version 4 sd card update
Click to expand...
Click to collapse
Is this an update to the Stock Rom?

hi, can u help me please, iam tryin to update with twrp , i did remove first line from script but i have error.

Found a way to unlock bands on MTK based phones by flashing basebands from phones with the same chipset. Doing this by using SPFLASH and flashing md1 files. Still unable to connect to cell network on my Doogee bl12000. Flashed this phones MD1, was wondering if anybody could provide me with the nvdata and nvram from the ZTE blase a2 plus. Hoping by flashing those files can connect to a U.S. network.

Moving from stock Android 5.0.1 to Resurrection Remix N v5.8.5.

Hello community!
First of all, I feel I have to apologize to you all since I know I have clogged the forum with a lot of requests of help about upgrading my smartphone... They are scattered all over the place so I have decided to gathered in a definitive one.
I have edited this post to make it a comprehensive guide for all the people who want to upgrade their HUAWEI P8 LITE ALICE from the stock Android 5.0.1 to the Resurrection Remix N v5.8.5. Before go any further I want you to read the following disclaimer:
PLEASE PLEASE PLEASE READ THIS!!
I am not a developer. I am not a programmer. I have been greatly helped by the user Botar230 so, unfortunately, I cannot help you in case of problems. I myself had problems and had to ask for help. The only thing I can say is to be always polite and try to explain, as best as you can, what's going on.
I will try to be as much clear as possible here but keep in mind that english is not my native language so it is possible that I might mistaking something. My apologize. I am not responsible for any damage you may do to your mobile and I am not responsible to any data loss it may occur. You should ALWAYS do a backup before proceeding. ALWAYS.
I've decided to flash Resurrection Remix N v5.8.5. because it is pre-rooted with Magisk.
BEFORE start to upgrade your mobile, read all this post twice and be sure to understood all the things I have written here. Check the links, check if you have the correct files, check if your mobile is fully charged, check if the bootloader is unlocked, check if you have the right ADB files and drivers downloaded and installed. Please do it BEFORE you start everything.
Done? Everything is fine? So, here we go!
GOAL: Moving from stock Android 5.0.1 to Resurrection Remix N v5.8.5.
MY MOBILE: Huawei P8 Lite ALICE (ALE-L21) unbranded single SIM - Build number: BalongC50B311 - Kernel 3.10.61-gcd3fde7 - EMUI 3.1
BOOTLOADER STATUS: unlocked, checked via ADB
The build number and the kernel number might differ. You should check them carefully and search around this forum how to proceed properly. Also, I totally don't know what to do if you have a double SIM phone. Sorry.
These are the files I have downloaded and put on the MicroSD before starting the whole process:
b895_update.zip
open_gapps-arm64-7.1-nano-20180702
RR-N-v5.8.5-20180302-alice-OpenKirin.zip
The file TWRP_3.1.1-0_ALICE_BL.img have to be put in the same directory where adb.exe is since you will flash it via adb command: fastboot flash recovery TWRP_3.1.1-0_ALICE_BL.img once you have entered in fastboot mode AND you have checked that your bootloader is unlocked.
Now, the next steps that worked for me are:
install TWRP_3.1.1-0 via ADB
Factory reset (Wipe -> Swipe to wipe)
update the device with b895_update to get Android 6.0 and EMUI 4 (by putting b895_update on the SD card and flash it via TWRP previously installed or via sideload as suggested by Botar230. I find myself comfortable to use ADB.)
install again TWRP_3.1.1-0_ALICE_BL via ADB or via sideload
Flash RR-N-v5.8.5-20180302-alice-OpenKirin) via TWRP AND at the same time...
Flash Open Gapps via TWRP. You HAVE TO USE THE ARM64 - 7.1 VERSION!!!
Reboot your device. It is done! :good:
NOTE!! Updating the phone to b895 will take really a lot of time. Seriously. It might be scary but it's ok. It will update EMUI too.
NOTE!! When you install TWRP via ADB, the TWRP_3.1.1-0_ALICE_BL.img file MUST BE in the same directory where the adb.exe file is.
At this point, everything should be fine, working and squeaky clean!
The ROM is pre-rooted with Magisk and that's pretty cool!
At this point I think my brief tutorial is over. If you find out something important missing or wrong, please point it out! It will help other people! Thank you!
Some links about ADB that I found quite useful:
How to Install TWRP Recovery via Fastboot On Any Android Device
How to Use ADB & Fastboot Commands with your Android Device
ADB Shell
Once again I have to thank the immense patience of BOTAR230 and all the people that worked so hard to make everything possible: I mean the guys (and gals? Maybe, I don't know... ) behind the Resurrection Remix ROM, behind the TWRP project and the Open Gapps and the many more I probably forgot! Thanks everyone!

DaGreatAssyr said:
Hello community!
First of all, I feel I have to apologize to you all since I know I have clogged the forum with a lot of requests of help about upgrading my smartphone... They are scattered all over the place so I have decided to gathered in a definitive one.
Next, I am quite insecure on all the steps so I will try to make a comprehensive list and keep it updated hoping it will help all the Huawei P8 Lite ALICE users that will do the same process I am about to do. Let's proceed!
GOAL: Moving from stock Android 5.0.1 to OpenKirin's MoKee
MY MOBILE: Huawei P8 Lite ALICE (ALE-L21) unbranded single SIM - Build number: BalongC50B311 - Kernel 3.10.61-gcd3fde7 - EMUI 3.1
BOOTLOADER STATUS: unlocked, checked via ADB
Now, the next steps would be to root the mobile. My wild guess are
install TWRP_3.1.1-0_ALICE_BL via ADB
install Magisk to root Android 5.0.1
At this point I am not perfectly sure if those steps are right AND if Magisk is the right choice to root Android 5.0.1 on my mobile. Are there other ways to do that?
Once the device is rooted, the next steps should be:
update the device with b895_update to get Android 6.0 and EMUI 4 (by putting b895_update on the SD card and flash it via TWRP previously installed)
install again TWRP_3.1.1-0_ALICE_BL via ADB
install again Magisk to root Android 6.0
install pa_alice-7.3.1-EOL-20180203 (or RR-N-v5.8.5-20180302-alice-OpenKirin)
That's the theory. I've used SR5-SuperSU-v2.82-SYSTEMMODE but it bricked the phone after I updated to Android 6.0 and the user Botar230 told me that it is no longer updated and used and suggested me to use Magisk instead.
The files I have are:
b895_update.zip
open_gapps-arm-7.1-stock-20180626.zip
RR-N-v5.8.5-20180302-alice-OpenKirin.zip
pa_alice-7.3.1-EOL-20180203.zip
TWRP_3.1.1-0_ALICE_BL.img
Previously, I have updated my device to Android 6.0 and installed TWRP 3.1.1-0 and everything went really good. When I tried to root the phone with SuperSU-v2.82, it bricked. Now the phone is restored to its initial conditions, brandless.
I have read THIS POST but it's pretty old and most of the link there are not working anymore.
So, if someone is kindly willingly to give me a hand (yeah, another one, I know... ) on this subject, I'd really appreciate it. Again.
Thanks in advance!
Click to expand...
Click to collapse
I didn't fully understand you, so I'll write a quick guide how to move from stock android 5.0.1 to any other custom ROM (I've read that you already unlocked your bootloader and flashed twrp so I'll skip those two)
First of all, use this version of TWRP.
1. Boot into TWRP
2. Factory reset (Wipe -> Swipe to wipe)
3. Flash B896 update (B895 is fine too)
4. Flash TWRP (Install -> Select image -> Recovery)
5. Flash a custom ROM of your choice
6. Flash Open GAPPS (I recommend flashing NANO version)
7. (Optionally) Flash Magisk if your custom ROM isn't pre-rooted (if unsure, check the root status before flashing)
Fun fact: You don't need to put every file on SD card to flash it. You can also use sideload

Botar230 said:
I didn't fully understand you, so I'll write a quick guide how to move from stock android 5.0.1 to any other custom ROM (I've read that you already unlocked your bootloader and flashed twrp
Click to expand...
Click to collapse
Hello Botar230! At the present time, I only unlocked the bootloader.
No TWRP installed so far.
Thank you for adding some steps I have missed (like the factory reset and the GApps! :good: )!!
The TWRP version I have is the same you suggested me so this is fine!
Yes, now that I think about, nearly all the custom ROM are pre-rooted and there's an option to switch the root in the setting panel but I will check it eventually.
I have make corrections in my list after your suggestion:
install TWRP_3.1.1-0_ALICE_BL via ADB
Factory reset (Wipe -> Swipe to wipe)
update the device with b895_update to get Android 6.0 and EMUI 4 (by putting b895_update on the SD card and flash it via TWRP previously installed or via sideload)
install again TWRP_3.1.1-0_ALICE_BL via ADB or via sideload
install pa_alice-7.3.1-EOL-20180203 (or RR-N-v5.8.5-20180302-alice-OpenKirin)
Flash open_gapps-arm-7.1-nano-20180630
Check whether the ROM is rootable and eventually flash Magisk
The files I have are:
b895_update.zip
open_gapps-arm-7.1-stock-20180626.zip (I will not use these)
open_gapps-arm-7.1-nano-20180630.zip (I will use these one! )
RR-N-v5.8.5-20180302-alice-OpenKirin.zip
pa_alice-7.3.1-EOL-20180203.zip
TWRP_3.1.1-0_ALICE_BL.img

Everything looks good now. Btw you don't need to flash nano gapps exclusively, it's just a matter of your personal preference which one you choose.
Sent from my LG-K220 using XDA Labs

Botar230 said:
Btw you don't need to flash nano gapps exclusively, it's just a matter of your personal preference which one you choose.
Click to expand...
Click to collapse
To be honest, I don't know what to choose between all the options I have seen on the website. Let's say that if the installation works properly it's a matter of seconds to make a backup and try another Gapp. For the moment I will follow your suggestion.
That's what I have done so far:
install TWRP_3.1.1-0_ALICE_BL via ADB DONE AND OK!
Factory reset (Wipe -> Swipe to wipe) DONE AND OK!
update the device with b895_update to get Android 6.0 and EMUI 4 (by putting b895_update on the SD card and flash it via TWRP previously installed or via sideload) DONE AND OK!
install again TWRP_3.1.1-0_ALICE_BL via ADB or via sideload DONE AND OK!
Everything is working fine so far but I am a little bit nervous about these one. I will take a deep breathe and I will proceed right now. I can flash the ROM and the Gapps with TWRP, right? I am mostly sure about but a confirm could ease my fear of bricking the phone again... :silly:
install pa_alice-7.3.1-EOL-20180203 (or RR-N-v5.8.5-20180302-alice-OpenKirin)
Flash open_gapps-arm-7.1-nano-20180630
Check whether the ROM is rootable and eventually flash Magisk

DaGreatAssyr said:
To be honest, I don't know what to choose between all the options I have seen on the website. Let's say that if the installation works properly it's a matter of seconds to make a backup and try another Gapp. For the moment I will follow your suggestion.
That's what I have done so far:
install TWRP_3.1.1-0_ALICE_BL via ADB DONE AND OK!
Factory reset (Wipe -> Swipe to wipe) DONE AND OK!
update the device with b895_update to get Android 6.0 and EMUI 4 (by putting b895_update on the SD card and flash it via TWRP previously installed or via sideload) DONE AND OK!
install again TWRP_3.1.1-0_ALICE_BL via ADB or via sideloadDONE AND OK!
Everything is working fine so far but I am a little bit nervous about these one. I will take a deep breathe and I will proceed right now. I can flash the ROM and the Gapps with TWRP, right? I am mostly sure about but a confirm could ease my fear of bricking the phone again... :silly:
install pa_alice-7.3.1-EOL-20180203 (or RR-N-v5.8.5-20180302-alice-OpenKirin)
Flash open_gapps-arm-7.1-nano-20180630
Check whether the ROM is rootable and eventually flash Magisk
Click to expand...
Click to collapse
Yes, everything is correct.
Sent from my LG-K220 using XDA Labs

Botar230 said:
Yes, everything is correct.
Click to expand...
Click to collapse
First of all, thank you for your immense patience!!
That's what happened so far:
install TWRP_3.1.1-0_ALICE_BL via ADB DONE AND OK!
Factory reset (Wipe -> Swipe to wipe) DONE AND OK!
update the device with b895_update to get Android 6.0 and EMUI 4 (by putting b895_update on the SD card and flash it via TWRP previously installed or via sideload) DONE AND OK!
install again TWRP_3.1.1-0_ALICE_BL via ADB or via sideload DONE AND OK!
install pa_alice-7.3.1-EOL-20180203 (or RR-N-v5.8.5-20180302-alice-OpenKirin) DONE AND OK!
I had to install the open_gapps-arm64 since the system required the ARM64 but apart that...
Flash open_gapps-arm64-7.1-stock-20180630.zip DONE BUT NOT OK! - I've tried to install the NANO and the STOCK Gapps but every time I got the same error message on TWRP: "failed to mount data: operation not supported on transport endpoint". Google Play and all the Google apps cannot connect: the Google error message is always the same: "couldn't sign in". I've double checked the login and they work both on my PC and on the other phones so I'm sure they are correct. Now I'm searching what kind of error it is but I'm not finding much infos about. Plus, there is the warning message saying that "Google Play services has stopped" and it keeps popping on the screen.
Check whether the ROM is rootable and eventually flash Magisk NOT DONE YET but it seems that it is not pre-rooted.
I am searching the web to understand what's going on here.

It's probably because the custom ROM that you've chosen uses f2fs file system on /data partition instead of ext4. Try to do this:
Boot to TWRP -> Wipe -> Advanced wipe -> Choose Data -> Repair or change file system. From here you can see if the file system of /data is ext4 or f2fs. If it's f2fs, then click Change file system and choose ext4.
Before doing all of this, you should flash b895 again, do a factory reset, flash twrp, flash your custom ROM, change /data file system, and finally gapps so there will be no conflicts between old and new gapps.

Hello again!
Sorry for the silence, got some busy day but here I am.
Before doing what you told me, I've tried to do a backup with TWRP and I've been flooded with error messages:
failed to mount '/data' (Operation not supported on transport endpoint)
Unable to recreate /data/media folder
Unable to mount storage
failed to mount '/data' (Operation not supported on transport endpoint)
Unable to mount /data/media/TWRP/.twrps
And, of course, the backup process failed.
At this point I cannot do anything with TWRP.
I cannot backup, cannot flash a ROM or a ZIP.
The phone works fine, it boots and I got no problems. I can boot it via ADB too.
I'm really scared it will brick or loop sooner or later. I am keeping it turned off and wait for any other advice before proceeding since it would be quite pesky to restart from scratch again....
Following your directions I've seen that the data file system is ext3.

DaGreatAssyr said:
Hello again!
Sorry for the silence, got some busy day but here I am.
Before doing what you told me, I've tried to do a backup with TWRP and I've been flooded with error messages:
failed to mount '/data' (Operation not supported on transport endpoint)
Unable to recreate /data/media folder
Unable to mount storage
failed to mount '/data' (Operation not supported on transport endpoint)
Unable to mount /data/media/TWRP/.twrps
And, of course, the backup process failed.
At this point I cannot do anything with TWRP.
I cannot backup, cannot flash a ROM or a ZIP.
The phone works fine, it boots and I got no problems. I can boot it via ADB too.
I'm really scared it will brick or loop sooner or later. I am keeping it turned off and wait for any other advice before proceeding since it would be quite pesky to restart from scratch again....
Following your directions I've seen that the data file system is ext3.
Click to expand...
Click to collapse
Don't worry, it won't brick. Maybe the internal storage is encrypted. In order to remove encryption, go to Wipe -> Format data.

Hello Botar230! Something funny (in a very positive way) happened! I did as you told me: I booted in recovery mode and went to WIPE -> FORMAT DATA.
Then I considered to install the other ROM I had, RR-N-v5.8.5-20180302-alice-OpenKirin and it has been the best idea I could have!!! :laugh:
After I formatted the data, I rebooted in recovery mode and checked that the problems where all disappeared and they actually did. Then I flashed the OpenKirin ROM and the Nano Gapps you told me.
SURPRISE SURPRISE the OpenKirin ROM is pre-rooted with Magisk 15.3 and the installation, this time, went perfectly fine without any trouble! Plus, Magisk updated to the latest version, the 16!
As I promised, I will now update my first post on how to upgrade my mobile phone hoping it will be useful for someone else but first I want to enjoy my brand new phone!
And, of course, I want to thank you for all the support you gave me in these days! You have been really patient and kind! I am really sorry I cannot help you back since (as you have noticed...) I am not much of an expert so all I can give you is my gratitude and thankfulness! THANK YOU 1000 TIMES BOTAR!! :highfive:

You're welcome. Have a nice day! :highfive:
Sent from my LG-K220 using XDA Labs