Database Users

Poweroff without reason

I all, help me please:
My htc make a reset it self or I find it poweroff without reason, I tried to change the battery with a new, and although I made her original rom the problem persists.

Had the same problem, send it in to service and received it two weeks later.
They said that they have replaced the platine. No further comments.
Cheers

Poweroff without reason....even after getting the battery replaced with a new one sounds like a hardware problem. Take it to the HTC service center.

Did you flash a new ROM to your device ?
Before I knew mine is an Elfin, I flashed Elf-ROMS to it
and that caused the same problems you mentioned.

Yes I flashed with onyx 3.2.1 before I had a PdaVietV66.
But the problem is: I returned to the original ISP/UPL with the original ROM and the problem is the same!
I try to set power/backlight setting always ON, I unchecked "Today timeout" in "setting->today>item" but I don't resolved.
In another site I found (but I don't understand how it)
"This seems to be a common problem, I have read about it on other forums. The fix is to remove the battery cover and put a small folded up piece of paper between the cover and the cover switch, to ensure the switch stays depressed. This seems to fix the powering down -AND- the memory card disappearing act. I don't have this phone yet, I just ordered it, so I can't give any more details about the location of the cover switch until it comes. Let us know if that fixes it"

Completely dead!
No hard reset, no power on, change battery.... niet, nada.
I sent it to assistance.

xoms said:
"This seems to be a common problem, I have read about it on other forums. The fix is to remove the battery cover and put a small folded up piece of paper between the cover and the cover switch, to ensure the switch stays depressed. This seems to fix the powering down -AND- the memory card disappearing act. I don't have this phone yet, I just ordered it, so I can't give any more details about the location of the cover switch until it comes. Let us know if that fixes it"
Click to expand...
Click to collapse
Having same problem with my touch, I have the diamond right now but would like to bring the old touch back to life!
Anybody know where to find this switch??
maybe some pics or a howto?
thx
thread link:
http://www.htcwiki.com/thread/457605/3125+power+down+for+no+good+reason?t=anon
Is this the position of the switch maybe? (green arrow)

Had the same problem with the default ROM and with TrueG V4. I followed what xoms found (many thanks) and in 2 days my Touch hasn't gone off once.
The switch does appear to be what you pointed out, romflasher. I put the paper on there to about the height of level with the rest of the inside shell. Hope you can get it to work.

Need Help -- How to disable S-View magnetic sensor ?

Well, I used the Google ROM Edition 4.3 untouched for nearly two months, so far so good, these days I woke up and looked at my S4 and came across this:
http://i.imgur.com/HnMb5Ov.jpg?1
no key nothing I do comes out of this screen, sometimes it goes back to normal and back to this screen again, I do not know what else to do, already tried to wipe and everything until it switched the official rom and give first boot I came across this:
http://i.imgur.com/imx5zRC.jpg?1
So I need help, and sorry for the english, I'm using a translator
Thank you
Samsung GT I9505 Galaxy S4
Samsung 64GB Class 10

That S-View cover screen. that should work only with this hardware feature. by covering light sensor you get this screen, try to disable this function in settings, but normally that looks like bug.

roomoonek1991 said:
That S-View cover screen. that should work only with this hardware feature. by covering light sensor you get this screen, try to disable this function in settings, but normally that looks like bug.
Click to expand...
Click to collapse
Thank you man, I was going crazy ahahah
more it can not be a hardware problem? because I thought that this function of the S-View only work on the samsung stock ROM or am I wrong? and I used the Google Edition 4.3 rom and never activated this option.
Thank you so much.

I looked about and found some people with this problem, but could not find any solution, I find strange because I never used any S-View cover, and option in settings did not work . If I try to change the rom you guys think the problem is solved?
Thanks

try to factory reset first, if that will not a solution, then try other rom. I hope that will help with your problem.

roomoonek1991 said:
try to factory reset first, if that will not a solution, then try other rom. I hope that will help with your problem.
Click to expand...
Click to collapse
I tried a factory reset and it did not work, I'll try another rom, I'm thinking of getting back to the store

Douglas Henrique said:
I tried a factory reset and it did not work, I'll try another rom, I'm thinking of getting back to the store
Click to expand...
Click to collapse
please guys, i need help =/

Douglas Henrique said:
please guys, i need help =/
Click to expand...
Click to collapse
=/

No.1 D5 dead after charging

New No.1 D5 here is the history:
Opened it up, turned it on and it was stuck in an endless boot loop. Tried disconnecting the battery, no luck.
After many attempts, I was finally able to flash the March 10th firmware onto it. It finally booted up. Played around with it for a bit and shut it down to charge the rest of the way.
After charging for a couple of hours, the unit is unresponsive. It won't turn on. It won't charge. The screen is just blank no matter what. Tried disconnecting the battery again, no luck. Checked the battery with a volt meter and it is at 3.87v.
If anyone has any suggestions, I would really appreciate it.
Thanks

Send it back. Must be a hardware issue.
If you mess with it anymore you will not be able to exchange it.

I think you could upgrade firmware again, to the old version

I re-flashed the new one again and it worked.

r2dr0id2 said:
I re-flashed the new one again and it worked.
Click to expand...
Click to collapse
Good news
Well done - it's nice to hear some good news :good:
Must have been an interrupted flash the first time.

r2dr0id2 said:
I re-flashed the new one again and it worked.
Click to expand...
Click to collapse
Aslo I suggest not update other firmware in addition to official firmware

Herberteten said:
Aslo I suggest not update other firmware in addition to official firmware
Click to expand...
Click to collapse
He didn't.
I have seen your posts on these forums - are you a sales rep ?

r2dr0id2 said:
I re-flashed the new one again and it worked.
Click to expand...
Click to collapse
Hi, how did you re-flashed the watch. I have some problem with mine. I can turn it on, see the No1 Logo coming up, but thats all. The screen stays on with the logo, until the battery is dead. I have tried to connect it to my laptop, which can see the device but cant do anything with it. I can only disconnect it. Before I had this issue with the watch I have deleted a couple of custom watch faces and just restarted the watch. But before that I had wireless update from NO1 on the watch. Any idea how could I retart it? Many thanks,
Balazs

I have the same problem and my computer not recognize the watch
r2dr0id2 said:
I re-flashed the new one again and it worked.
Click to expand...
Click to collapse
I have the same problem and my computer not recognize the watch.
How can i re-flash the new one again or the old one?

Same deal
After one day and one charge the screen went black.

People - the watch has to be OFF to flash the firmware.
If you read the sections on using the SP Flashtool you will note that the PC will only recognize the watch when SP Tools is running and the watch is off.
If you connect with the correct drivers installed while SP tool is running and the watch is off it will flash the new firmware.
Read up on it.

I have the same problem, when my battery went down to 40% then watch switched off and didn't wanted to start again.
When I was trying to connect it via docking station it has used up remaining power of the battery and now it is dead.
I have found information's that it is software issue and watch drop USB connection and only way to fix it is by flashing of the firmware.
Only problem is that battery in the watch is dead and all attempts of recharging it doesn't work.
I am not sure if this will work but I have removed the back cover of the watch and disconnected small connector to the battery.
I will leave watch disconnected for 24h maybe it will clear all the information's and I will be able to recharge the battery and flash the firmware. When I got the watch (2 days ago) it was working ok (apart of massive battery drain even in airplane mode) therefore I hope that it come back to original state.

creatorsappox said:
Hi, how did you re-flashed the watch. I have some problem with mine. I can turn it on, see the No1 Logo coming up, but thats all. The screen stays on with the logo, until the battery is dead. I have tried to connect it to my laptop, which can see the device but cant do anything with it. I can only disconnect it. Before I had this issue with the watch I have deleted a couple of custom watch faces and just restarted the watch. But before that I had wireless update from NO1 on the watch. Any idea how could I retart it? Many thanks,
Balazs
Click to expand...
Click to collapse
the problem probably because of the watch faces you've deleted if they builtin to the launcher. go to Lokifish Marz G+ you'll find the guide on how to falsh the rom.
---------- Post added at 09:11 PM ---------- Previous post was at 09:10 PM ----------
creatorsappox said:
Hi, how did you re-flashed the watch. I have some problem with mine. I can turn it on, see the No1 Logo coming up, but thats all. The screen stays on with the logo, until the battery is dead. I have tried to connect it to my laptop, which can see the device but cant do anything with it. I can only disconnect it. Before I had this issue with the watch I have deleted a couple of custom watch faces and just restarted the watch. But before that I had wireless update from NO1 on the watch. Any idea how could I retart it? Many thanks,
Balazs
Click to expand...
Click to collapse
eladbend86 said:
I have the same problem and my computer not recognize the watch.
How can i re-flash the new one again or the old one?
Click to expand...
Click to collapse
go to Lokifish Marz G+ you'll find a guide there what to do and how to flash the rom.
---------- Post added at 09:13 PM ---------- Previous post was at 09:11 PM ----------
DrHappy said:
After one day and one charge the screen went black.
Click to expand...
Click to collapse
go to Lokifish Marz G+ you'll find the guide there on what to do and how to flash the rom.

Sadly it didnt helped, I had watch disconnected from the battery for 24h, the screen is still black, watch doesnt charge, and when you connect to PC it keeps restarting.
The message that I have is:
USB device not recognize The last USB device connected to this computer malfunctioned and Windows does not recognise it.
Device keep restarting and give this message over and over again.
I must say that it is the worst device that I ever had. One day of using it, poor battery performance and now this.

Dead No.1 D5 after charge
Kazuya22 said:
Sadly it didnt helped, I had watch disconnected from the battery for 24h, the screen is still black, watch doesnt charge, and when you connect to PC it keeps restarting.
The message that I have is:
USB device not recognize The last USB device connected to this computer malfunctioned and Windows does not recognise it.
Device keep restarting and give this message over and over again.
I must say that it is the worst device that I ever had. One day of using it, poor battery performance and now this.
Click to expand...
Click to collapse
Dude i bought 3 watches 6 weeks ago and 2 of them are having this same issue.
i left them to charge at night and they never came back...
i tested the battery and its charged, i also charged it with an external power supply....
Im not worried cuz i got the money back from GB but im disappointing i have 2 dead units setting here and will not make the same mistake
i think they have a hardware problem they are not talking about.

Update of 85 mb

I got today an update of 85 mb in my lenovo vibe note 5 a7020a48 but i dont know what changed.

It will only fix some bugs and increase stability.

srijesh said:
I got today an update of 85 mb in my lenovo vibe note 5 a7020a48 but i dont know what changed.
Click to expand...
Click to collapse
Yes, it's not adding any functionality to your Android. It just fixes some bugs and problems occurring to your current rom.

i got my phone on 20th, i updated the 80 mb update. Then the next day the phone was hanging and no controls were working. The blue led was blinking. Then the screen was dim, had to restart by holding power button for 10sec. The same issue repeated once each day and today it came two times
Any fix or cause for this fault?

seshadripr said:
i got my phone on 20th, i updated the 80 mb update. Then the next day the phone was hanging and no controls were working. The blue led was blinking. Then the screen was dim, had to restart by holding power button for 10sec. The same issue repeated once each day and today it came two times
Any fix or cause for this fault?
Click to expand...
Click to collapse
Go to recovery mode and wipe cache.

Did that and still same
Ashwinrg said:
Go to recovery mode and wipe cache.
Click to expand...
Click to collapse
Y this fault is occuring
I did a factory reset and still it occurs.

seshadripr said:
Y this fault is occuring
I did a factory reset and still it occurs.
Click to expand...
Click to collapse
I think ota update provided by your manufacture have bugs. When you update your android then it replaced files that you have before in your stock rom.
So, if you factory reset then the new OTA update also include in your factory stock rom. Because update replaced files and new files taken place of factory stock.

Pathetic from lenovo. Many youtube videos show same fault
Ashwinrg said:
I think ota update provided by your manufacture have bugs. When you update your android then it replaced files that you have before in your stock rom.
Click to expand...
Click to collapse
And my friend has same phone bought 4 months back. It is working good without this fault. Have asked for replacement from flipkart. Hope new one is good
---------- Post added at 12:50 AM ---------- Previous post was at 12:18 AM ----------
seshadripr said:
And my friend has same phone bought 4 months back. It is working good without this fault. Have asked for replacement from flipkart. Hope new one is good
Click to expand...
Click to collapse
The fingerprint sensor is worstly developed. When we keep unrecognised finger on the sensor.
It keeps on scanning the unrecognised finger .
It should be like it must scan only once .
And the next scan will be only when the finger is lifted and placed on sensor again.
Xiaomi redmi note 3 has perfect design for fingerprint sensor

seshadripr said:
And my friend has same phone bought 4 months back. It is working good without this fault. Have asked for replacement from flipkart. Hope new one is good
---------- Post added at 12:50 AM ---------- Previous post was at 12:18 AM ----------
The fingerprint sensor is worstly developed. When we keep unrecognised finger on the sensor.
It keeps on scanning the unrecognised finger .
It should be like it must scan only once .
And the next scan will be only when the finger is lifted and placed on sensor again.
Xiaomi redmi note 3 has perfect design for fingerprint sensor
Click to expand...
Click to collapse
If it can replace. Then better to replace your phone and get new one.

Failure in SWM8802

Good Morning.
I hope you can help me with this problem.
I have a 2 din SWM8802 Android.
When the car is stopped, I can use it without problems, but as soon as I start walking, an image appears on the screen constantly, even if I'm just listening to music. When this image comes out, the sound is lowered
In the device options, I have the video warning disabled, but the image continues to appear and is not the video warning.
* I do not know what to do.
I have already restored the factory settings and I have updated the Android version, but it is still happening.
I wait for your help.
Thank you very much.
//imageshack.com/a/img922/5330/Zes50T.jpg

a screen shot would help immensely.......

Thank you.
This is the image.
//imageshack.com/a/img922/5330/Zes50T.jpg
See if you can help me because I do not know what to do anymore.

This looks like the back up camera input came on. Normally this is triggered by applying 12v to the brown wire (next to the pink one).
Make sure this wire is insulated and not touching a power cable.
By the way i have the same unit. Where did you get the update files?

stavragi said:
This looks like the back up camera input came on. Normally this is triggered by applying 12v to the brown wire (next to the pink one).
Make sure this wire is insulated and not touching a power cable.
By the way i have the same unit. Where did you get the update files?
Click to expand...
Click to collapse
Goodnight.
Thank you very much for your answer.
I have checked the cables and at first glance they seem well insulated.
Can there be another reason?
The update I do not remember where I downloaded it from.
But I have it.
How can I get it to you?

asthio said:
Goodnight.
Thank you very much for your answer.
I have checked the cables and at first glance they seem well insulated.
Can there be another reason?
The update I do not remember where I downloaded it from.
But I have it.
How can I get it to you?
Click to expand...
Click to collapse
Thanks. I have some issues with the device as well so this may help me.
You can upload them at "https:// uploadfiles .io " (spaces are to let me post a url, just remove them) and then post the download link here or pm me.
For your issue i would try and connect the pink wire (brake sensor) to ground permanently if you haven't done that already.
If this doesn't help i would try to connect the brown to the ground as well. It shouldn't affect the unit in any way but since it is not standard connectivity you do it at your own responsibility.
P.S. there are two brown wires. the second is the steering wheel control input. There should be a sticker at the bottom of the device to help you identify which is for what.
If not let me know and I can send you a photo from mine.

stavragi said:
Thanks. I have some issues with the device as well so this may help me.
You can upload them at "https:// uploadfiles .io " (spaces are to let me post a url, just remove them) and then post the download link here or pm me.
For your issue i would try and connect the pink wire (brake sensor) to ground permanently if you haven't done that already.
If this doesn't help i would try to connect the brown to the ground as well. It shouldn't affect the unit in any way but since it is not standard connectivity you do it at your own responsibility.
P.S. there are two brown wires. the second is the steering wheel control input. There should be a sticker at the bottom of the device to help you identify which is for what.
If not let me know and I can send you a photo from mine.
Click to expand...
Click to collapse
Well, if you do not mind, send me the photo, please.

asthio said:
Well, if you do not mind, send me the photo, please.
Click to expand...
Click to collapse
I sent you a private

asthio said:
I sent you a private
Click to expand...
Click to collapse
Thanks for the file.
I uploaded an image here https:// ibb. co/bFOgxn
full size picture
It shows what each cable is for. I have also circle the two cables I suggest you connect to ground (parking, backup camera)
My reasoning for suggesting grounding the backup camera cable is because these cables usually have a pull down resistor internally
to keep the signal to 0V until 12v are connected (camera activated). If this pull down resistor is not working correctly, then connecting this cable to the ground signal can resolve the issue.
I hope this helps.

I tested your update btw. It is still android 5.1.1 but I prefer the visuals of this version so thanks for this.
Unfortunately it didn't fix the issue i have with this device. The sound is not coming out properly. It may be a HW issue but it doesn't hurt to try.
Can i bother you for a setting from your device? It's in the factory settings. (You can set your car logo from there as well if you haven't done that already)
Settings > Factory Settings (passcode is 1983) > Second Button from the left > Hardware Testing (swipe right to get there) > De-Sense > PLLs > AUDPLL
Mine is set to -1 but i believe that's wrong.

I also have a problem with mine SWM8802 unfortunately it is now in a reboot loop and I do not know how to get it out there
you have said that you updated yours how did you do it or where did you get the ROM from?

stavragi said:
I tested your update btw. It is still android 5.1.1 but I prefer the visuals of this version so thanks for this.
Unfortunately it didn't fix the issue i have with this device. The sound is not coming out properly. It may be a HW issue but it doesn't hurt to try.
Can i bother you for a setting from your device? It's in the factory settings. (You can set your car logo from there as well if you haven't done that already)
Settings > Factory Settings (passcode is 1983) > Second Button from the left > Hardware Testing (swipe right to get there) > De-Sense > PLLs > AUDPLL
Mine is set to -1 but i believe that's wrong.
Click to expand...
Click to collapse
Give me a couple of days and I'll answer you

xdidi0 said:
I also have a problem with mine SWM8802 unfortunately it is now in a reboot loop and I do not know how to get it out there
you have said that you updated yours how did you do it or where did you get the ROM from?
Click to expand...
Click to collapse
I send you a private

stavragi said:
I tested your update btw. It is still android 5.1.1 but I prefer the visuals of this version so thanks for this.
Unfortunately it didn't fix the issue i have with this device. The sound is not coming out properly. It may be a HW issue but it doesn't hurt to try.
Can i bother you for a setting from your device? It's in the factory settings. (You can set your car logo from there as well if you haven't done that already)
Settings > Factory Settings (passcode is 1983) > Second Button from the left > Hardware Testing (swipe right to get there) > De-Sense > PLLs > AUDPLL
Mine is set to -1 but i believe that's wrong.
Click to expand...
Click to collapse
solved
I removed the pin number 2, the one from the antenna, and it works perfectly.
I have looked at the settings you mention to me and it says -1.
Thank you very much.
Whatever you need, ask for it.

A user send it to me. Here is a copy (just remove the spaces). But i used the update option in the settings. I don't know how you could apply it if your device is in a boot loop.
https:// ufile. io/eu919
---------- Post added at 10:42 PM ---------- Previous post was at 10:20 PM ----------
asthio said:
solved
I removed the pin number 2, the one from the antenna, and it works perfectly.
I have looked at the settings you mention to me and it says -1.
Thank you very much.
Whatever you need, ask for it.
Click to expand...
Click to collapse
I'm glad you got it fixed. :good::good::good:
I'm pretty sure mine is a hw issue but since you are offering
I would really appreciate if you could do the tedious work and write me all the PLL values from that menu.
It's my last hope to find a sw solution for my issue.

stavragi said:
A user send it to me. Here is a copy (just remove the spaces). But i used the update option in the settings. I don't know how you could apply it if your device is in a boot loop.
https:// ufile. io/eu919
---------- Post added at 10:42 PM ---------- Previous post was at 10:20 PM ----------
I'm glad you got it fixed. :good::good::good:
I'm pretty sure mine is a hw issue but since you are offering
I would really appreciate if you could do the tedious work and write me all the PLL values from that menu.
It's my last hope to find a sw solution for my issue.
Click to expand...
Click to collapse
I send you a private with the values

Hello! I have been looking for help on this SWM8802. I do apologize in advance if this is a threadjack. I don't know if you have the same issue but when I turn on the radio and switch to another source - the radio is still playing. That and a hiss in the background (that doesn't increase or decrease in volume but does turn off at volume0).
I got a host of other question (why does it only have Key1 - where's key 2?)
My HU has Android 7.1 BTW - at least that what it says on the information page on the machine.

arivee said:
Hello! I have been looking for help on this SWM8802. I do apologize in advance if this is a threadjack. I don't know if you have the same issue but when I turn on the radio and switch to another source - the radio is still playing. That and a hiss in the background (that doesn't increase or decrease in volume but does turn off at volume0).
I got a host of other question (why does it only have Key1 - where's key 2?)
My HU has Android 7.1 BTW - at least that what it says on the information page on the machine.
Click to expand...
Click to collapse
One thing I can tell you there is no Android 7.1 installed because we were all ripped off.
because the Build.prop was manipulated Actually, on this device Android 4.4.1 installed

stavragi said:
A user send it to me. Here is a copy (just remove the spaces). But i used the update option in the settings. I don't know how you could apply it if your device is in a boot loop.
https:// ufile. io/eu919
---------- Post added at 10:42 PM ---------- Previous post was at 10:20 PM ----------
I'm glad you got it fixed. :good::good::good:
I'm pretty sure mine is a hw issue but since you are offering
I would really appreciate if you could do the tedious work and write me all the PLL values from that menu.
It's my last hope to find a sw solution for my issue.
Click to expand...
Click to collapse
I have tried the update and now i went back from ALPS.LD_kk1.MP10.V1.4 to ALPS.LD_kk1.MP10.V1.2
So i cannot disable the beep now every touch on the screen beeps
Does someone have the ALPS.LD_kk1.MP10.V1.4 so that i can get back to it? ALPS.LD_kk1.MP10.V1.6 would be good to.
Cheers

Bonjour j'ai le même autorzdio swm8802. Il est decrit decu 2 sortie video output sur les rca av1 et av2 mais dans la notice elle sont en entrée input.
Je voulais brancher un second ecran mais bien sur ca marche pas. Est il possible de passer les entrées input en sortie output?