Good evening!
This is my first post and I would get a fix on my device, if is possible.
I found every kind of tutorial to flash this device.
I used differents version of Odin with no success
My device is:
Samsung Galaxy A7 SM-A700F
In ODIN MODE appear those details:
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
REACTIVATION LOCK: OFF
Secure Download: Enabled
KNOX WARRANTY VOID: 1
RP SWREP: 2
I tried to put into this device Android 4.4 (original rom) and the last one.
I can access only on Download Mode, but not in Recovery Mode... I would make a wipecache, or reset nand, but I can't get into Recovery Mode.
I bought online as not working phone, so I don't know what can I do on it.... Could be bricked?
Related
Hi guys. I'm having some problems with my Note 4. I previously have rooted the phone, but tried to use SuperSU to unroot it. I was getting errors loading some apps telling me that phone was still rooted so I attempted to do a factory reset on the phone. Somewhere along the road I appear to have messed up the firmware.
Basically, when powered on my phone states "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again." If I open the recovery menu on my phone (power+home+vol. down) it says
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-N910F
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
REACTIVATION LOCK: OFF
KNOX WARRANTY VOID: 0x1 (4)
QUALCOMM SECUREBOOT: ENABLE (CSB)
AP SWREV: S1, T1, R1, A1, P1
SECURE DOWNLOAD: ENABLE
UDC START
I have tried using Kies (both versions) which say that my phone is not recognised in the emergency firmware recovery options, and the firmware upgrade option fails.
I have also tried using Odin using firmware N910FXXU1COJ3_N910FO2U1COJ1_O2U and N910FXXU1BOC3_N910FO2U1BOC1_O2U.
I am totally stuck for ideas. Is my phone bricked?
Unfortunately I can't upload screen shots due to my account status.
Kaetor said:
Hi guys. I'm having some problems with my Note 4. I previously have rooted the phone, but tried to use SuperSU to unroot it. I was getting errors loading some apps telling me that phone was still rooted so I attempted to do a factory reset on the phone. Somewhere along the road I appear to have messed up the firmware.
Basically, when powered on my phone states "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again." If I open the recovery menu on my phone (power+home+vol. down) it says
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-N910F
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
REACTIVATION LOCK: OFF
KNOX WARRANTY VOID: 0x1 (4)
QUALCOMM SECUREBOOT: ENABLE (CSB)
AP SWREV: S1, T1, R1, A1, P1
SECURE DOWNLOAD: ENABLE
UDC START
I have tried using Kies (both versions) which say that my phone is not recognised in the emergency firmware recovery options, and the firmware upgrade option fails.
I have also tried using Odin using firmware N910FXXU1COJ3_N910FO2U1COJ1_O2U and N910FXXU1BOC3_N910FO2U1BOC1_O2U.
I am totally stuck for ideas. Is my phone bricked?
Unfortunately I can't upload screen shots due to my account status.
Click to expand...
Click to collapse
Do you use Stock Kernel or custom Kernel?
d4rkkn16ht said:
Do you use Stock Kernel or custom Kernel?
Click to expand...
Click to collapse
I'm not sure. I assume stock.
Kaetor said:
I'm not sure. I assume stock.
Click to expand...
Click to collapse
Judging for your answer I assume that you are kinda "new" to this ROOT & flashing ROM stuff?
Am I correct?
If you are "new" to this stuff....I suggest you read & re-read everything before "plunging deep into the abyss"
Now the answer,
ROOT & Stock 5.1.1 Lollipop Kernel is a NO GO!
By updating your KitKat 4.4.4/Lollipop 5.0.1 into Lollipop 5.1.1 (BTW COJ stock update IS Lollipop 5.1.1) will remove your ROOT access.
Re-ROOTing it will cause a bootloop....IF you didn't change your kernel into a "Permissive" one.
Try flashing a custom permissive kernel if you are going to keep ROOTed.
It'll fix your problem.
Download ODIN, then go to samfirmware and download some software for your phone. Use Odin to flash whatever firmware back onto your phone and start again.
Please Help me I don't Know the right FIRMWARE For this device. Here's an Information that I saw in my device. I'm really Confused what ROM to download. I used Safestrap App and Wipe My Device and It turns out Stuck at Samsung Logo with a picture of Padlock (that is Unlocked) and below the padlock it says "Custom". All I Can do is to go to DOWNLOAD MODE. I hope someone can Help or Give me Information. TIA
1.) When I try to update the software, my screen goes to AT&T Update screen, So I think it's an AT&T Device.
2.) When I go to DOWNLOAD MODE, Here's what I see:
Odin Mode.
SGH-I337
Binary: Samsung Official
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x0
CSB-Config-LSB: 0x30
Write protection: enable
eMMC burst mode enabled
3.) Please See these Attachment Pictures (I use Sammobile App to Identify my device Info.)
Your device is what download mode says.
The pad lock screen is only on the AT&T s4 which is the sgh-i337. The phone has a locked bootloader and can only run custom ROMs that can be flashed using safestrap. You will need to re-flash the stock firmware.
This may help: https://forum.xda-developers.com/ga...-to-update-to-i337oc3-5-0-1-keeproot-t3075814
Hi all,
Please bear with me, I'm in way over my head here and don't understand most of what I've done. I was experimenting when I probably shouldn't have been.
So, I installed DarkLord's Note 7 kernel and rom. I found it to be quite buggy and am now wanting to wipe my phone and install Phronesis-N9005-N7-v6.0.
Problem is, when trying to boot into TWRP, I'm met with the the following:
ODIN MODE
Product name: SM-N9005
Current binary: Custom
System status: Official
Reactivation lock(kk): Off
Knox Kernel lock: 0x0
Knox warranty void: 0x1
Qualcomm secureboot: Enable (csb)
Rp swrev: S2, T2, R2, A3, P3
Write protection: Enable
UDC start
Downloading...
Do not turn off target
I've had it on for hours and it didn't do anything.
I managed to reboot it and it ran as it did before, in Darklords rom.
I read I have to install the official firmware and install it via Odin but I can't find anything about my device. On the back of it, it says:
SM N9005
FCC ID - A3LSMN9005
SNN - N9005GSMH
When I enter it into sammobile, nothing comes up.
Have I got this wrong? Should I be looking for something else?
You are booting to download mode not recovery .
Boot to recovery TWRP
#N9005 model firmware are on sammobile etc.
https://forum.xda-developers.com/galaxy-note-3/general/samsung-galaxy-note-3-sticky-roll-t3237249
Booting into recovery via TWRP manager just results in the same Odin screen for me
As for the firmware - I'm not really sure which region I should pick out of those. I just thought this was an international model, but then I downloaded an app called Phone INFO and it tells me it's Vietnam. Could this be because of the rom already on there? It does also say it's a Note 7, so I'm assuming it's incorrect.
TWRP manager
DO NOT USE just boot to recovery via the vol up home and power buttons as normal .
Copy Phronesis to ext sd card and flash as per instructions .
You have N9005 Pick your area /network where you are .
Phone Info can only go by what's on your phone and you flashed DarkLord's Note 7 firmware .
Booting via manager was a last resort. I was trying the usual way and it also resulting in the same thing.
Boot to download/ Odin mode flash stock rom .
Thanks JJEgan, I figured out how to use Odin3 and Odin mode, then install Phronesis. All is good now
Hi,
I have bought a second life Samsung Note 3 ( SM-N9005 ) here in the Netherlands.
I was so tempted to install a custom ROM, that I immediately installed TWRP with Odin v3.09. It took me several times to install TWRP 3.3.0-0, as the phone returned with its own T-mobile logo. (I had forgotten to set the developers options before doing something.)
Then I tried to install lineage-16.0-20190907-nighty-hlte-signed.zip file via TWRP. It fails with an error 7.
and: E3004: This package is for device: hlte, hltespr, hltexx; this device is hltechn.
(does this means there is a (replaced) main-board in this phone?)
I have updated the modem and bootloader files via Odin, selected BL with the file N9005_Nordic_XXUGPQB1-Modem_XXSGBQD1-Bootloader.tar. But I can't see if this has succeeded or not. TWPR doesn't see this file on my SD card, so I used Odin.
Is there a way to get around this and install LineageOS 16.0 on this phone?
It shows only the booting logo SM-N9005, but then it 'hangs'.
TMobile are you sure its an N9005 .
Boot to download mode to check .
There is a placard under the battery, stating: model SM-N9005 SSN: -N9005GSMH
in download mode:
Odin mode
product name: SM-N9005
current binary: Custom
system status: Custom
reactivation lock: Off
qualcomm secureboot: enable (CSB)
RP swrev: S2, T2, R2, A3, P3
secure download: enable
udc start
TWRP should not see your tar file only Odin .
I was able to install TWRP. When I boot in recovery mode, TWRP starts fine.
When I try to install LineageOS zip file and trying to install LineageOS, it fails with an error 7.
This package is for device: hlte, hltespr, hltexx; this device is hltechn.
How can a phone, that shows to be an EU model sm-n9005, coming up with a message it is a hltechn, in TWRP?
I have spent enough time and money on this phone. -- Project cancelled --
Lucky the phone came with a nearly new, Samsung cover.
So my own original Note 3 with Lollipop, looks as new again.
Hi and thanks for reading this,
I received a SM-T580 from my grandson, he was playing with it experimenting some hacking
but seems he bricked the tablet , and I do not know what he was trying to do,
and in fact he does not know either.
Now i'm in a situation that the tablet does not boot, can not power off, it just goes straight to downloading page,
and I can go to odin mode pressing home, vol- and power.
In odin mode I have:
download speed: fast
product name: sm-t580
current binary: samsung official
system status: custom
reactivation lock: off
crom service: on
secure download: enabled
warranty void: 0 (0x000)
rp swrev: b:6 k:3 s:4
I have try to install stock firmware but i got bootloader error,
in fact the newest firmware has bootloader 5,
installing only AP stops at system.img after few seconds.
I do not know how to go out from this situation,
just hope in your help.
many thanks
old uncle
fixed by @hainguyenthao