Database Users

[WARNING] Flashing the chineese update.zip will block all further updates FIXED!

Edit: Solution found look below!!!

As I posted in a different thread:
I managed to do it, but it was hackish
How I did it:
Used a terminal directly on the tablet, no adb.
I installed the acer chinese update. I 'dd'ed my old system and flexrom and rebooted. After that I checked for updates, and as luck had it, there was one. I tried it, but it failed half way through the procedure.
I rebooted again, then I 'dd'ed a boot.img on mmcblk0p2 from a 1.016 that matched my original system.img and flexrom.img. WITHOUT REBOOTING (I tried that before, it gives a bad kernel checksum and stops, but I assumed on update it would just patch if the file corresponds and re-sign), I then proceeded to do the update. It rebooted, entered recovery, and lo and behold, IT WORKED! So I'm 100% back to stock.
I would imagine that the same procedure would work when manually updating through recovery (using an extracted update.zip).
I used the kernel from here:
http://forum.xda-developers.com/showpost.php?p=14033507&postcount=27
EDIT: The kernel is stock for ACER_A500_1.016.05_COM_GEN1
Take a look at the thread linked below, get the 1.016.05_COM_GEN1 files (system, flexrom, and boot). If you are not offered an online update (System>About>Check for updates), you need the official update.zip from Acer. Extract the update.zip from the official Acer update THAT MATCHES YOUR FLEX VERSION using the XOR 12 method (see here - http://forum.xda-developers.com/showthread.php?t=1065360&page=20 - note in that post the link is for 03_COM_GEN1, NOT 05_COM_GEN1. For 04_COM_GEN1 and 05_COM_GEN1 see here - http://forum.xda-developers.com/showpost.php?p=14052165&postcount=184. For 03 and 04 you will need to find system.img, flexrom.img and boot.img, for 05 they are linked in the thread below).
EDIT: The thread with the images for ACER_A500_1.016.05_COM_GEN1 is here:
http://forum.xda-developers.com/showthread.php?t=1086785
EDIT: You might pull this off for other flex versions as well, but you would need all the files (system.img, flexrom.img, boot.img AND update.zip) from those versions.
PLEASE NOTE THAT THIS ONLY WORKS IF YOU HAVE THE OFFICIAL UPDATE.ZIP FOR YOUR SPECIFIC FLEX VERSION

Wow, I was about to try that!!!
I'll do that now and see how it goes.
Thanks mate!
EDIT: Worked!

I would expect that the reason an update fails on the Chinese one is that it tries to patch the kernel (which is different from the one expected). The update is a bunch of diffs and patches, and almost no full files, so it cannot be applied over anything but the right files.

Yes that is true. The old kermel checksum check was failing.

huxflux2003 said:
EDIT: Worked!
Click to expand...
Click to collapse
Glad to hear it Take that, you sneaky Acer bastards!

adancau said:
As I posted in a different thread:
I managed to do it though, but it was hackish
How I did it:
Used a terminal directly on the tablet, no adb.
I installed the acer chinese update. I 'dd'ed my old system and flexrom and rebooted. After that I checked for updates, and as luck had it, there was one. I tried it, but it failed half way through the procedure.
I rebooted again, then I 'dd'ed a boot.img on mmcblk0p2 from a 1.016 that matched my original system.img and flexrom.img. WITHOUT REBOOTING (I tried that before, it gives a bad kernel checksum and stops, but I assumed on update it would just patch if the file corresponds and re-sign), I then proceeded to do the update. It rebooted, entered recovery, and lo and behold, IT WORKED! So I'm 100% back to stock.
I would imagine that the same procedure would work when manually updating through recovery (using an extracted update.zip).
I used the kernel from here:
http://forum.xda-developers.com/showpost.php?p=14033507&postcount=27
Take a look at the thread, get the 1.016 files, system, flexrom, and boot, and try it.
Click to expand...
Click to collapse
Ahhhh a true milestone, well done.........

Nice work! Two questions:
Does the update work in the US?
I assume gingerbreak still works after the OTA update?
Thx

gingerbreak works

_motley said:
Does the update work in the US?
I assume gingerbreak still works after the OTA update?
Click to expand...
Click to collapse
A warning first: You DO NOT need to do this if you haven't installed the chinese update.zip (update.acer.zip) before, as that is the only one that changes kernels. Also, if you have anything other than ACER_A500_1.016.05_COM_GEN1, it's debatable if you want to do this (if you do read below), it might be better to wait for an official update.
The kernel above is stock for ACER_A500_1.016.05_COM_GEN1
So it works if you have ACER_A500_1.016.05_COM_GEN1 images, or are ok with changing your flex to that (in which case you would need to flash a system.img and a flexrom.img for ACER_A500_1.016.05_COM_GEN1, reboot, and then flash the kernel from the post above before heading off to recovery and updating - HOWEVER as far as I know no one has tried this, though IN THEORY it should work).
Gingerbreak still works, you can get root back after updating.

Just so I'm clear...
I'm at version 1.139.05 but I got here via the Chinese update.zip.
What do I need to do to get back to stock? Do I need to go back to my old system image and flexrom plus a new kernel?
Could someone post clearer instructions?
Thanks

adancau said:
A warning first: You DO NOT need to do this if you haven't installed the chinese update.zip (update.acer.zip) before, as that is the only one that changes kernels. Also, if you have anything other than ACER_A500_1.016.05_COM_GEN1, it's debatable if you want to do this (if you do read below), it might be better to wait for an official update.
The kernel above is stock for ACER_A500_1.016.05_COM_GEN1
So it works if you have ACER_A500_1.016.05_COM_GEN1 images, or are ok with changing your flex to that (in which case you would need to flash a system.img and a flexrom.img for ACER_A500_1.016.05_COM_GEN1, reboot, and then flash the kernel from the post above before heading off to recovery and updating - HOWEVER as far as I know no one has tried this, though IN THEORY it should work).
Gingerbreak still works, you can get root back after updating.
Click to expand...
Click to collapse
Thanks guys, I did restore using the Chinese update.zip last week and I am currently sitting at kernel 2.6.36.3 with flashed system img=Acer_A500_1.104.05_COM_GEN1, but with recovered Chinese kernel modules for wifi etc. I also flashed a flexrom.img from this build as well. I didn't flash the boot.img from this build, but was thinking about it until huxflux2003 reported the check-sum failure.
So, I am trying to decide what I am going to do. It sounds easy enough to get back to stock now, but I may wait for the official update next month that has 3.1. At this point, I suppose we are assuming that it will be a full update.zip that will work on any tablet (god I hope so). It's about time they gave us a full recovery image...I will be beyond disappointed if they don't. Let's also just hope we can still gain root easily after this.
One more question, if I use all the images from ACER_A500_1.016.05_COM_GEN1 that were posted, does this have to match what I had originally had in any shape or form? It sounds like since all the pieces are from the same build, everything will be fine regardless of what you had to begin with. Is this right?
Thx

To your last question - Theoretically yes, it should work, and I guess you don't need to match what you originally had. I can only speculate, logically though it would makes sense. You definitely need all the images to be from the same build (system+flexrom+boot.img). You also need the official update for that build.

heyoh said:
Just so I'm clear...
I'm at version 1.139.05 but I got here via the Chinese update.zip.
What do I need to do to get back to stock? Do I need to go back to my old system image and flexrom plus a new kernel?
Could someone post clearer instructions?
Thanks
Click to expand...
Click to collapse
To get back to stock you need the three images for your build - system, flexrom, and boot. If there is no online update available, you also need the update.zip for that build (extracted from an official acer update using the XOR 12 method - do a search).
Alternatively, I suppose you could switch to a new build for which you could find all the necessary files (but it hasn't been tried).
Flash system.img using dd. You might need to re-root. Reboot, flash flexrom.img. Reboot once more. Make sure your wifi works (you might need different kernel modules).
Look to see if there is an online update (Settings > About > Check for updates). If there is, cancel it. Flash boot.img on mmcblk0p2. DO NOT REBOOT.
If there was an online update available, now it's the time to perform it. After it's done you will get you back to stock 1.139.05.
If there isn't any update, make sure you have the update.zip on the root of your microSD. Turn off the tablet, then turn it back on holding the volume key closest to the power button. Do not let go of that button until you see some text in the corner. At that moment the update would begin. Once rebooted you will be back to stock.
Hope I've explained it better this time, and it works ok for you. If not, you need to go through the chinese update again. Good luck.

adancau said:
To your last question - Theoretically yes, it should work, and I guess you don't need to match what you originally had. I can only speculate, logically though it would makes sense. You definitely need all the images to be from the same build (system+flexrom+boot.img). You also need the official update for that build.
Click to expand...
Click to collapse
It worked for me too! Thanks again for the tip. I am now at the latest build and ahead of the US update schedule from what I can gather
It asked me to update after I flashed the ACER_A500_1.016.05_COM_GEN1 build system.img and flexrom.img. Even from the US it prompted just fine since I was on ACER_A500_1.016.05_COM_GEN1 build and not ACER_A500_1.104.05_COM_GEN1 as the former is what the differential patch targets.
I cancelled the update once I saw it presented and then blew on the boot.img from the ACER_A500_1.016.05_COM_GEN1 build. Then, without rebooting, I downloaded and applied the update (but with a little hiccup, see below). Now I am at Acer_A500_1.139.05_COM_GEN1 and didn't lose any user apps or settings etc.
Had a scary point though that I will share as it may help others. The first time I tried, the zip wouldn't downloadload and I was getting an HTTP 403 error. I cleared the systemupdater app and FWUpdateService data. I also killed the services and then I was stuck. Instead of conceding to reflashing the Chinese update.zip and starting over, I unzipped the Chinese update.zip and grabbed the boot.img from it. I then dd'ed that image back to the boot partition and rebooted again. It came back up and I this time I was able to do the system update successfully. Whew!

Followed instructions by OP and it worked perfectly! Back to stock and updated.
I think I'll be keeping these system images for next time I brick and have to flash the Chinese update.

Any chance of someone uploading the extracted update.zip for the new Acer_A500_1.139.05_COM_GEN1 so I can update manually using this method.
Thanks in advance

I used the above method to update to 1.139.04 from 1.016.04.
However my kernel is still 2.6.36.3-00001-gf991e5d instead of the 2.6.36.3 everyone else is reporting?

tianqi said:
I used the above method to update to 1.139.04 from 1.016.04.
However my kernel is still 2.6.36.3-00001-gf991e5d instead of the 2.6.36.3 everyone else is reporting?
Click to expand...
Click to collapse
If you directly flashed a 1.139.04 image your kernel has not been updated. You had to flash a 1.016.04 image, flexrom and boot, and then run the update.
You MIGHT have some luck regardless by running the update.zip now (I used it on mine one time when I updated like you did, and it seemed to work, but I have not noticed the kernel number). Be prepared to have to reflash if something goes wrong though.

I did reflash system, flexrom, and boot from 1.016.04...
Second time is still the same...
Kernel is still 2.6.36.3-00001-gf991e5d...

Important/Urgent: Who has a STOCK Verizon tab 7.7 (SCH-i815)

I need help! I need a stock, unmodified recovery partition image.
Anyone here with a vzw tab who DOES NOT yet have CWM installed?.
PLEASE contact me.
Thanks!

electron73 said:
I need help! I need a stock, unmodified recovery partition image.
Anyone here with a vzw tab who DOES NOT yet have CWM installed?.
PLEASE contact me.
Thanks!
Click to expand...
Click to collapse
I have one that hasn't been moded but have no idea how to get you what you want. PM me if you know how to download and send to you and I'll do my best to help.

I'll check my laptop at home tonight. I believe I kept my heimdall backup before flashing cwm
Sent from my DROID BIONIC using Tapatalk 2
Just checked, mightve deleted it. Sorry man

aximtreo said:
I have one that hasn't been moded but have no idea how to get you what you want. PM me if you know how to download and send to you and I'll do my best to help.
Click to expand...
Click to collapse
Oh that would be awesome! Are you rooted? Let me find the commands in the meantime, I read somewhere it's a simple one command in terminal to extract the recovery partition into a file on sd card...

WHAT AN ORDEAL !!!!
But in the end: SUCCESS!
I managed to get my tab updated with the Verizon OTA update.
The problem is definitely CWM !!! A rude awakening is in store for everyone with the P6800 CWM installed, because it a) fails to verify the checksum of OTA files correctly on the i815, b) it thinks the tablet is a P6800, so the OTA file fails to run if it assert checks for "SCH-i815" hardware AND lastly c) modem updates don't work because the device /dev/cdma_update doesn't exist, so the modem.bin firmware_update call fails !!!
In short, I had to fumble the OTA file apart and do the update manually in two runs:
First file, kick the checksum, hardware check and modem update out, then manually run the ZIP through CWM. The zip subsequently (LUCKILY) updated the stock recovery and overwrote CWM with a new fresh stock recovery.
Second file had everything kicked out BUT the modem udpate and LTE patch, so with the STOCK recovery this file ran through just fine, updated the modem and then applied the LTE delta patch.
Phew!!!
Of course I had to manually restore root after the update, had backed up with voodoo, auto restore failed, so terminal and hacking it was...
Now I have the tab running on clean stock FD01, baseband and LTE FD01, rooted and stock recovery.
No more CWM, no more "hacking" with the ROM until some dev finally releases a "correct" CWM and at least ANY factory ODIN image is available to bring the tab back to stock if needed!!!
Kinda sick of the non-support for this tab. So much going on for the Galaxy Note and pretty much every other device. I'm starting to regret having bought this "special" Verizon version

Awesome find and great to know for whenever ics does come out. Could you please post the recovery img you got?
Sent from my DROID BIONIC using Tapatalk 2

OK after getting so many responses I decided to just post everything here in hopes that it will help others, too:
All files are here:
http://www.mywo.org:88/XDA/sch-i815/index.php
Step by step procedure to update the Verizon Tab from ..FA02 to ..FD01 build IF YOU ARE stuck with CWM installed on your tab and the original OTA fails with errors:
Upload the SCH-I815_FA02c_To_FD01.1.zip to the INTERNAL(!) SD card. This is important because CWM contains a bug that will only allow you to install from ZIPs stored on the INTERNAL SD storage.
Upload the SCH-I815_FA02c_To_FD01.2.zip to the EXTERNAL(!) (micro SD) card. This is important, because after the factory recovery is restored, it will correctly (and only) look for ZIPs on the EXTERNAL card.
Best way just copy both files to both locations
Fire up CWM and do "install from ZIP" and select SCH-I815_FA02c_To_FD01.1.zip
It should run (takes a while) and eventually tell you all is done. BOOT the tab. It should boot fine but in system it will show the new Android build FD01 but the baseband (radio) will still be the "old" one.
Now press and hold power and vol up again until you see the default Samsung recovery menu. Choose install from ZIP and select SCH-I815_FA02c_To_FD01.2.zip. This will now upgrade the baseband only. When done, reboot and enjoy being back on the "factory upgrade path" with the tab.
I hope someone more savvy than me can "fix" CWM to work properly with VZW tabs (accept the checksum, not fail the check for "SCH-i815" and provide the correct /dev file links for radio upgrades). Until then, I recommend just leaving the tab as-is and not tinkering with the ROM. Not that there is any custom ROM available anyway :-(
I also pulled the NEW factory recovery image FD01_recovery.img with the following command:
dd if=/dev/block/mmcblk0p6 of=/sdcard/FD01_recovery.img bs=4096
So in case anyone with a botched recovery wants to restore factory (Samsung 3e) recovery. This was actually the reason I had to go through all this... There is NO factory recovery image ANYWHERE to be found. I can't believe that I should be the first one ever to post one?? Anyway, hope it will help
I'm still quite new here, so I do really appreciate every click on that "thanks" button
P.S. for tinkerers and devs I also uploaded the original, untouched OTA file (0559c0e4e08e.update_SCH-I815_FA02c_To_FD01.bin) as it came from Samsung or Verizon or whatever and ended up in the /cache partition.

THANK YOU!
Electron,
You sir, are a BOSS! Thank you so very much for doing the work, and sharing it. You just made things one hell of a lot easier on me, and anyone else that follows.
Regards,
-Rob

Also want to say thanks. You rock, dude. I wouldn't have known how to revert **** on my own.
Also, I feel like we need a sticky or something for sch-i815 owners to go to for device specific stuffs, especially since there is little knowledge/info out for this device.
Sent from my Galaxy Nexus using xda premium

hmm i only ever installed ROM manager ... but i did root it ... problem is ... now i don't have a CWM recovery to flash the file ... any ideas?

phigmeta said:
hmm i only ever installed ROM manager ... but i did root it ... problem is ... now i don't have a CWM recovery to flash the file ... any ideas?
Click to expand...
Click to collapse
You're in luck! You don't need to go through the whole ordeal because you do NOT have CWM! You can just update the regular intended way. Go into settings, about phone and then click check for system updates. If it presents you the OTA update, just do it the regular way.
My complicated "hack" is only necessary if you DO HAVE CWM installed.

Im sorry I did not explain well what my issue is.
I do not have CWM installed, however i did delete a few appilcations using titanium backup. This causes updates to not take. I would really like to just take it back to factory and start over (this time with less stupidity on my part)
I of course would assume that once its at factory i can then install updates again.
Right now when i try i get the "!" droid sign and a reboot

phigmeta said:
Im sorry I did not explain well what my issue is.
I do not have CWM installed, however i did delete a few appilcations using titanium backup. This causes updates to not take. I would really like to just take it back to factory and start over (this time with less stupidity on my part)
I of course would assume that once its at factory i can then install updates again.
Right now when i try i get the "!" droid sign and a reboot
Click to expand...
Click to collapse
Hey
OK unless someone can tell us how to "make" an ODIN flashable ROM for you, here is what I would do (and please don't get scared because it sounds a bit convoluted).
First, you need to be rooted. This is obviously the case.
IMPORTANT since you don't have CWM installed yet, SAVE your factory restore.img before proceeding, this saves you a lot of hassle later!
Open the android terminal, type su (accept the prompt) and then type (or copy/paste)
dd if=/dev/block/mmcblk0p6 of=/mnt/sdcard/factory_recovery.img bs=4096
Check that you have a "factory_recovery.img" file on your sd card now it should be about 8M big.
Now you're safe to install CWM from the forum, look for the other thread(s) where this is being discussed and follow the instructions for the P6800 "international" version with 3G. CWM Thread here:
http://forum.xda-developers.com/showthread.php?t=1613638&highlight=cwm&page=3
Then (thanks to nicduim!) there is a full factory (rooted) CWM image floating around on the forums here:
http://forum.xda-developers.com/showthread.php?t=1613638&page=6
Which I used to restore my tab to "almost factory" with the missing bloat apps back in place.
I have a copy on my server here: http://ww.mywo.org:88/XDA/sch-i815/ it's the "2012-05-06.22.48.58.ZIP"
unzip that and put the contents on your INTERNAL SD card in the folder clockwordmod. So on your internal SD you should have /clockworkmod/2012-05-06.22.48.58 and inside there the files boot.img, recovery.img etc.
Use CWM recovery to restore this backup. If you never used CWM before. Press power button and volume up and hold both until you see the menu screen with text. You can go up/down with the volume buttons (go slow, it's very laggy) and with the power button you "select" an option. Select the "restore from backup" option and point it to the only folder being offered, the 2012-05-06.22.48.58.
The restore takes a while, then reboot the tab. Now you're back to stock! Last thing you need to do is get rid of CWM again because in the end it's still a bit buggy and will prevent the OTA update from running properly.
Since you luckily have a backup of the factory recovery in form of that factory_recovery.img file, just install and open terminal again, type su and then type (or copy)
dd if=/mnt/sdcard/factory_recovery.img of=/dev/block/mmcblk0p6 bs=4096
This overwrites CWM with your original Samsung Android recovery.
Now you just reboot as usual, connect to the internet and wait until the popup message shows up that a system update is ready, accept it and enjoy
If you don't want to wait for the automatic OTA, you can also stop before killing CWM and use my convoluted 2-step manual update which will get you to the exact same condition as the official OTA.
Hope all this makes sense

I was already on stock FD01 when I tried installing CWM for the P6800 that's floating around here somewhere. Odin said it was a success, but it looks like it didn't take. I've done it a few times, but still ended up w/ the stock recovery. However, after reading through your thread, I do not see a /dev/cdma_update in my I815 either. Is it possible that my attempt to install CWM (although unsuccessful) wiped out this file, among others?
Right now, I'm still at stock FD01 (rooted) and everything seems to be working. When I tried doing an OTA update, it just tells me that I have the latest update and no newer update is available.
One other thing, if I have to, I only have the stock recovery right now since CWM didn't take, can I simply flash both zip's using the Samsung stock recovery to put everything back in stock?
SCH-I815_FA02c_To_FD01.1.zip
SCH-I815_FA02c_To_FD01.2.zip

AlpineMan said:
I was already on stock FD01 when I tried installing CWM for the P6800 that's floating around here somewhere. Odin said it was a success, but it looks like it didn't take. I've done it a few times, but still ended up w/ the stock recovery. However, after reading through your thread, I do not see a /dev/cdma_update in my I815 either. Is it possible that my attempt to install CWM (although unsuccessful) wiped out this file, among others?
Right now, I'm still at stock FD01 (rooted) and everything seems to be working. When I tried doing an OTA update, it just tells me that I have the latest update and no newer update is available.
One other thing, if I have to, I only have the stock recovery right now since CWM didn't take, can I simply flash both zip's using the Samsung stock recovery to put everything back in stock?
SCH-I815_FA02c_To_FD01.1.zip
SCH-I815_FA02c_To_FD01.2.zip
Click to expand...
Click to collapse
Oh wait, so you are saying that in "About device" your Android is 3.2
Baseband i815.04 V.FD01 I815FD01
and your Build number is already at HTJ85B.I815FD01.SCH-I815.I815FD01 ?
That would mean you are already updated. In this case, it should be pretty easy to fix your problem. Which apps did you delete with Titanium? I can back them up from my system and make them available for you. All you'd need to do is drop the backup files into your Titanium backups folder and then fire up titanium and restore them!
The /dev/cdma_update node is only required WITHIN CWM recovery, so that is nothing for you to worry about. The zip files above won't help you because they are incremental updates requiring your system to be at FA02, not FD01 !

Yes... I'm already in the latest update. I already backed up the bloatware using Titanium Backup before uninstalling. So I just need to restore them back in order to receive and apply OTA updates in the future?
Sent from my SPH-D710 using Xparent ICS Blue Tapatalk 2

Please Help
Hi. I'm rooted and removed all sorts of bloatware with Titanium. I did this a long time ago and did not back anything up because I'm used to running hardware with custom ROMs available, and not relying on OTA updates.
Since there aren't any custom ROMs for the i815, I'd like to get ready for the upcoming ICS update. To do so, I want to get FD01 loaded onto my device, but I can't update because I've apparently removed too much of the required bloatware.
Does anyone know WHAT pieces of bloatware I'd need to reinstall in order for the OTA update to apply? I'd assume I can restore them and then apply the update and re-root.
If anyone can help pinpoint what missing APKs might help, I'll give them a shot. And, to the extent I figure anything out, I'll repost here in the hopes that it helps someone else.

electron,
Your instructions worked ... thank you so much

@jkrell... the failed attempt at installing the update should return an error message(s). You just have to read through them until you find the culprit(s). Apparently I uninstalled a few odexed files that were needed. I couldn't update until i hunted them down and restored them.
I guess we all jumped at the opportunity to install the cwm recovery image, that we didn't even think about cmda updates....ooops. So far i had to do a complete factory restore after the update. I was getting soft bricked to the point where I had no choice. Good thing I sent all titanium backups to actual sd card, i was able to salvage 97% f my data..... with the exception of a few downloads i forgot to move.
Gamecih doesn't work anymore (either version). No more automative data hacks I'm not sure what's going on. I uninstalled adfree..used titanium backup to uninstall both versions and reinstalled both several times. Oh well.
It really sucks not having nandroid backups but it's not worth the trouble of having to do this everytime an OTA modem update gets pushed to my tab. Needless to say, I won't be odining the cwm based recovery image again.
I'm with the O.P. I wish i hadn't wasted my money on this tab. No true cwm for this tab, so no dev will ever waste thier time with this tab. The sch i815 will soon be forgotten about and some other tablet will be all the hype before summer ends....that's just how it is. 21 months left on my contract.... [email protected]#k my life. Lol

Thanks Smitty.
When I try to update, I just see the "!" logo and then the device reboots. Is there a log file somewhere I can look at to see what the errors are?
I hear ya on the gloom and doom, but this device has only been out for just over 3 months now. I'd expect a recovery and some custom ROMs to come eventually. I doubt I'll go the custom ROM route unless CyanogenMod is supported, because I have no complaints about the tablet's performance thus far. It's speedy, smooth and the battery lasts forever.
In my book, this is a great tablet and I'm satisfied with the purchase.

[firmware][mt7-l09-v100r001c00b141]

From Huawei Russia:
http://consumer.huawei.com/ru/support/downloads/detail/index.htm?id=41906
Download
The same Official B141 with embedded SuperSU
Download
The embedded SU version will work only with the force update (three buttons) method; after installation it will ask to update the SU binary when you open it, update and restart.
Source

Lollipop.?
Edit: never mind, it's kitkat

First impression: (I did a local update)
1- smoother than the B137 rom
2- Camera improved than B137
3- Battery usage is good as B130 & B120

Root procedure remain the same as before?

Good to know.. 2 maybe stupid questions.. : I'll just flash it from Recovery? And root? English language as well right? Thanks

simika said:
Good to know.. 2 maybe stupid questions.. : I'll just flash it from Recovery? And root? English language as well right? Thanks
Click to expand...
Click to collapse
You can flash it using Local Update on update settings. English language is included

Great I'll try tonight! P. S. Root will stay then?

simika said:
Great I'll try tonight! P. S. Root will stay then?
Click to expand...
Click to collapse
OK i reply to myself
1 - you need to be on STOCK recovery... (so i went back from CWM to stock )
2 - install the file
3rd install again CWM and then install Superuser
everything working

So what's different with this version than B137?

never mind managed to get it from work

Hello. I'm in V100R001C00B127 without root. Can I install this firmware? It will root my device directly?

with this version of firmware battery life is just amazing, 137 was terrible for me

I just try to local uodate .its start updating from beginning but fail in half way.why?
I don't root my phone and stock recovery.I am on 137 right now

We can we expect this firmware for OTA in region Sweden ?

gthebest said:
Hello. I'm in V100R001C00B127 without root. Can I install this firmware? It will root my device directly?
Click to expand...
Click to collapse
Same question :S

I guess I've got the same question. I'm on 137. I've put this on my internal SD card as well as my ext SD card and went into update mode. It does the usual and looks like its updating but at around 90%-95% it just sit frozen for hours. When I unplug and reboot I'm still on 137 with no changes. I've also put this in the download folder under the Hauwei systemx86 folder that the suite software created and tried restoring my device with it. The software doesn't seem to find this package as a restore. I guess I'm gonna let the PC suite software make a backup and see what it names it and just rename this package to whatever it names my backup then try restoring with it. I'll get back to ya with the results. If you have any other advice I sure could use it. Cuz no way in hell I'm porting or building a ROM without a custom recovery.

mattwheat said:
I guess I've got the same question. I'm on 137. I've put this on my internal SD card as well as my ext SD card and went into update mode. It does the usual and looks like its updating but at around 90%-95% it just sit frozen for hours. When I unplug and reboot I'm still on 137 with no changes. I've also put this in the download folder under the Hauwei systemx86 folder that the suite software created and tried restoring my device with it. The software doesn't seem to find this package as a restore. I guess I'm gonna let the PC suite software make a backup and see what it names it and just rename this package to whatever it names my backup then try restoring with it. I'll get back to ya with the results. If you have any other advice I sure could use it. Cuz no way in hell I'm porting or building a ROM without a custom recovery.
Click to expand...
Click to collapse
I was on 137 and simply copied update.app file into DLOAD folder of the SD and it worked like a charm.
I suggest you to re-download the (big) update.app file, directly from Huawei website (russian) and linked in the post above.

i did the same as above and it worked for me

OK. I just didn't know what folder it was supposed to go in. But I did download the one with SuperSU built in and put it in SDcard/DLoad then went to Settings/Updater/Local. And flashed it like that and I'm all good now. I'm on the 141 update with Root and SuperSU was built in. Now,......is it safe for me to use flashify or some other apk to install CWM even though I have not unlocked the boot loader yet? I sound like such a noob (which I'm not its just this phone and its root/boot loader/ recovery methods are so different coming from LG, Samsung, and Moto)? Just trying to be cautious.

Does the force update (three button) method completely wipe the device?

[SOLVED] Error installing recent OTA update, anyone help or provide insight?

Went to update "YB1-X90L_170420" and as I have been normally doing I removed root, ran the update, and all was well. It installed fine and worked no problem.
I was then prompted for update "YB1-X90F_USR_S000408_1704201342_WW06_BP_ROW_TO_YB1_X90F_USR_S000426_1705080316_WW06_BP_ROW" So I started the download and when the device reboots it then fails with this string, note the error about the "build fingerprint"
Supported API: 3
Finding update package...
Opening update package...
Verifying update package...
Installing update...
Package expects build fingerprint of Lenovo/yeti_10_row_wifi/yeti:6.0.1/MMB29M/LenovoYB1-X90F_S000408_170420:user/release-keys or Lenovo/yeti_10_row_wifi/yeti:6.0.1/MMB29M/LenovoYB1-X90F_S000426_170508:user/release-keys; this device has Lenovo/yeti_10_row
E:Error in @/cache/recovery/block.map
(Status 7)
Installation aborted.
I foolishly after some googling and not finding enough info opened a chat with Lenovo. The rep asked what the error was and once I showed it said that was just related to my fingerprint scanner .... really?!?!? I knew the chat was a dead spot at this point but tried to state this device has no fingerprint reader, etc.. and so on. Hope they could really tell me what the error was. Anyway the rep told me to 'ignore' the update and just carry on since my device is actually working. They then went on to state they are hardware only on the chat session, which the Lenovo site says nothing about that. They then also told me to take this up with Google as they make Android not Lenovo. So much for warranty helping anything but possibly replacing a physically broken device. Their techs are useless, seriously.
So anywho, as you see in the error the update is trying to apply but looks for "Lenovo/yeti_10_row_wifi" and is finding somewhere (in the update or my device?) "Lenovo/yeti_10_row", notice the missing "wifi" on the end of that. My 'build.prop' and other system files are untouched. I even tried resetting the device. Which after the reset I was able to once again install the "YB1-X90L_170420" update but this next update "YB1-X90F_USR_S000408_1704201342_WW06_BP_ROW_TO_YB1_X90F_USR_S000426_1705080316_WW06_BP_ROW" fails again on that same fingerprint mismatch.
Any clue what I should be looking for here? Has anyone else installed that update successfully?
Will anyone here supply me with the original (or as close as original) clean stock ROM without paying for it? I know I should have backed up with TWRP before I started doing updates, and this may well be my issue, but I didn't and not I can only restore back to an already rooted backup. Though I assume doing a reset of that rooted restore is considered clean (no root or 3rd party anything)?
thanks for any help or ideas!

MarkAllen said:
Went to update "YB1-X90L_170420" and as I have been normally doing I removed root, ran the update, and all was well. It installed fine and worked no problem.
I was then prompted for update "YB1-X90F_USR_S000408_1704201342_WW06_BP_ROW_TO_YB1_X90F_USR_S000426_1705080316_WW06_BP_ROW" So I started the download and it the device reboots then fails with this string, note the error about the "build fingerprint"
Supported API: 3
Finding update package...
Opening update package...
Verifying update package...
Installing update...
Package expects build fingerprint of Lenovo/yeti_10_row_wifi/yeti:6.0.1/MMB29M/LenovoYB1-X90F_S000408_170420:user/release-keys or Lenovo/yeti_10_row_wifi/yeti:6.0.1/MMB29M/LenovoYB1-X90F_S000426_170508:user/release-keys; this device has Lenovo/yeti_10_row
E:Error in @/cache/recovery/block.map
(Status 7)
Installation aborted.
I foolishly after some googling and not finding enough info opened a chat with Lenovo. The rep asked what the error was and once I showed it said that was just related to my fingerprint scanner .... really?!?!? I knew the chat was a dead spot at this point but tried to state this device has no fingerprint reader, etc.. and so on. Hope they could really tell me what the error was. Anyway the rep told me to 'ignore' the update and just carry on since my device is actually working. They then went on to state they are hardware only on the chat session, which the Lenovo site says nothing about that. They then also told me to take this up with Google as they make Android not Lenovo. So much for warranty helping anything but possibly replacing a physically broken device. Their techs are useless, seriously.
So anywho, as you see in the error the update is trying to apply but looks for "Lenovo/yeti_10_row_wifi" and is finding somewhere (in the update or my device?) "Lenovo/yeti_10_row", notice the missing "wifi" on the end of that. My 'build.prop' and other system files are untouched. I even tried resetting the device. Which after the reset I was able to once again install the "YB1-X90L_170420" update but this next update "YB1-X90F_USR_S000408_1704201342_WW06_BP_ROW_TO_YB1_X90F_USR_S000426_1705080316_WW06_BP_ROW" fails again on that same fingerprint mismatch.
Any clue what I should be looking for here? Has anyone else installed that update successfully?
Will anyone here supply me with the original (or as close as original) clean stock ROM without paying for it? I know I should have backed up with TWRP before I started doing updates, and this may well be my issue, but I didn't and not I can only restore back to an already rooted backup. Though I assume doing a reset of that rooted restore is considered clean (no root or 3rd party anything)?
thanks for any help or ideas!
Click to expand...
Click to collapse
From what i recall the fingerprint is what is shown in the buildprop. You could try editing this but i would tread carefully if its just a minor update as it may justmess up your system if there are other mismatches during the update process.
Lenovo technical support is a complete joke, you get much better help here. Lol
Sent from my F5121 using Tapatalk

Nope every line of my build.prop, where listed, has the proper "Lenovo/yeti_10_row_wifi" that the update claims is wrong. I personally think it is this update itself but no confirmation from other users if the update
"YB1-X90F_USR_S000408_1704201342_WW06_BP_ROW_TO_YB1_X90 F_USR_S000426_1705080316_WW06_BP_ROW"
has installed for them yet.
And I certainly knew how far I was *not* going to get with Lenovo but figured it couldn't hurt. I was really trying to get a stock ROM download from them or anywhere. I would love to just revert this to how it was out of the box and start over.

Well for reference I think I finally realize what is causing this (unconfirmed, but sounds feasible).
I did at one time try the "YB1-X90L_USR_S000155_1609272258_WW06_BP_ROW" noted in another thread here from Easy firmware. I figured since it was a free download and others have done it, what could it hurt? lol (I think I know now). Anyway I forget what it was at the time but something with that rom just wasn't right for me and I decided to restore back to my TWRP backup I had made. I'm assuming my backup doesn't overwrite something that "L" version rom did and leaves some residue that reports itself as the "L" model now?
Anyway that is the only thing to me that makes sense to me that could be happening. Of course I have no original stock rom with IMG files to flash again to fix this. :/
Can anyone here confirm Easy Firmware is safe to use? Can anyone confirm their YB1-X90F rom is really that models rom?

MarkAllen said:
Well for reference I think I finally realize what is causing this (unconfirmed, but sounds feasible).
I did at one time try the "YB1-X90L_USR_S000155_1609272258_WW06_BP_ROW" noted in another thread here from Easy firmware. I figured since it was a free download and others have done it, what could it hurt? lol (I think I know now). Anyway I forget what it was at the time but something with that rom just wasn't right for me and I decided to restore back to my TWRP backup I had made. I'm assuming my backup doesn't overwrite something that "L" version rom did and leaves some residue that reports itself as the "L" model now?
Anyway that is the only thing to me that makes sense to me that could be happening. Of course I have no original stock rom with IMG files to flash again to fix this. :/
Can anyone here confirm Easy Firmware is safe to use? Can anyone confirm their YB1-X90F rom is really that models rom?
Click to expand...
Click to collapse
Hi,
I registered for the free account. Had to email there support team to get it activate as there were problems their end. The 90F firmwares were not in the free tier so I paid the $15 through paypal to be safe, and got the 90F firmware fine. It was old and I had to run a lot of updates to get it up to date. But it got everything back to how it should be.
I blame Lenovo that we have to jump through theese hoops, but the files are legit.

Broomfundel said:
Hi,
I registered for the free account. Had to email there support team to get it activate as there were problems their end. The 90F firmwares were not in the free tier so I paid the $15 through paypal to be safe, and got the 90F firmware fine. It was old and I had to run a lot of updates to get it up to date. But it got everything back to how it should be.
I blame Lenovo that we have to jump through theese hoops, but the files are legit.
Click to expand...
Click to collapse
Thanks for that confirmation! I did end up getting a registered account ($15) used Paypal and all looked good. I ended up downloading two versions of firmware. Initially I thought I would start with the oldest knowing many updates awaited but really wanted to be sure in erasing all my previous steps just in case it didn't work or the same thing happened again.
Used "YB1-X90F_USR_S000036_1607280616_WW6_BP_ROW-flashfiles.zip" from Easy Firmware. I opted to follow the included "installer.cmd" but did not do the "unlock" or "lock" as I already was unlocked of course and did not want to lock it again. When it completed I first noted my Halo keyboard not working and things were in Chinese here and there. This post resolved both items (thanks vimalbhimani!). Pretty sure that was because I formatted all the various partitions including "country", duh. Sadly however this version was showing no further OTA updates were available at all. Maybe Lenovo has deleted some of the really old OTA downloads and they are no longer available? Not sure.
I then installed the most recent rom "YB1-X90F_USR_S000196_1611040312_WW06_BP_ROW-flashfiles.zip". This time I did not format and only flashed this newer roms boot, bootloader, factory, recovery, and system images. After the system was backup everything was in great shape and updates were available. I made a TWRP backup straight away. Then I let the first and second updates listed below download and install via OTA and had no issues. The final two I opted to save time and installed using the standard recovery from my SD card after I downloaded them from my PC. Here are direct links to those if anyone wants them and they are in order of install (descending) based on already having "YB1-X90F_USR_S000196_161104"
http://tabdl.ota.lenovomm.com/dls/v...S000239_1612091428_WW06_BP_ROW_WCAC703BC6.zip
http://tabdl.ota.lenovomm.com/dls/v...S000340_1702251540_WW06_BP_ROW_WC365253B3.zip
http://tabdl.ota.lenovomm.com/dls/v6/YB1-X90F_170420_WC76FD00EF.zip
http://tabdl.ota.lenovomm.com/dls/v...S000426_1705080316_WW06_BP_ROW_WC80C2A0F2.zip (this is the failed update that incited this thread)
All updates went great and all is well at this point. Made another TWRP backup and I plan to root again now and see if any upcoming updates later have some issue?

I just wanted to report back here if anyone was interested that I unrooted, updated the June OTA update, and was able to root again without issue.

i got the same error message and now i'm stuck. I cant install any updates and so i bought a account from easy-firmware to get the firmware ... the firmware: YB1-X90F_USR_S000036_1607280616_WW6_BP_ROW-flashfiles.zip
doesnt not work with twrp or the stock recovery... it tells me "zip file is corupt"
@MarkAllen: Can you provide a guide how you got back to the stock rom? just flashing the zips doesnt work....
i really need help...

FreddeHamm said:
i got the same error message and now i'm stuck. I cant install any updates and so i bought a account from easy-firmware to get the firmware ... the firmware: YB1-X90F_USR_S000036_1607280616_WW6_BP_ROW-flashfiles.zip
doesnt not work with twrp or the stock recovery... it tells me "zip file is corupt"
@MarkAllen: Can you provide a guide how you got back to the stock rom? just flashing the zips doesnt work....
i really need help...
Click to expand...
Click to collapse
You cannot flash the ZIP file with TWRP or stock recovery. You have to unzip the file and then flash each IMG file that you need manually while in fastboot mode (there are seven of them).
**** IF YOU FOLLOW THESE DIRECTIONS IT IS NO ONES FAULT BUT YOUR OWN IF IT SCREWS UP SOMETHING!!! ****
**** WILL TRY TO HELP PROVIDE INFO IF I CAN BUT CANNOT GUARANTEE ANYTHING. ALSO THIS ERASE ALL YOUR DATA ****
First be aware as noted in the previous post above that I tried using "YB1-X90F_USR_S000036_1607280616_WW6_BP_ROW-flashfiles.zip" intially and it worked fine to get me back up and running but once I was done no new OTA updates were showing at all. No clue why so I ended up doing it again but used the ROM named "YB1-X90F_USR_S000196_1611040312_WW06_BP_ROW-flashfiles.zip". Also note I had erased my "country" partition and flashed "country.img" which requires the info posted by vimalbhimani again linked above in my previous post. It has to be used to correct for your country, no biggie at all and worked fine for myself.
1) Unzip the ROM you downloaded to a folder on your PC
2) From command prompt go to that folder
3) Make sure from the command prompt that ADB and fastboot commands are working properly
4) Put your tablet in fastboot mode ("adb reboot bootloader")
(these next commands are directly from the "install.cmd" included with the ROM from EasyFW, I just opted to run them manually one at a time in order and I omitted the unlock and lock commands)
fastboot flash gpt gpt.bin
fastboot erase misc
fastboot erase persistent
fastboot erase frp
fastboot erase metadata
fastboot format config
fastboot format country
fastboot format cache
fastboot format data
fastboot format factory
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash config config.img
fastboot flash country country.img
fastboot flash system system.img
fastboot flash bootloader bootloader
fastboot flash oemvars bootloader_policy-oemvars.txt
fastboot continue
That's it. Minus the Intel error code 03 for being unlocked, it should be a normal out of the box setup when it boots back up into Android.
good luck!

People that are looking for the YB1-X90F_USR_S000196_1611040312_WW06_BP_ROW-flashfiles.zip may want to take a look at this post.
In contrast to my experiences with devices made by other OEMs, it seems like the files can directly be used for downgrading the Yoga Book if you're currently using a newer version.

Moved...

Patched 11.0.12.12.KB05AA ROM for rooted users - install from Fastbootd!!!

[UPDATE]:
**********
I got sick of my phone telling me I needed to update but I couldn't because I'm rooted. So finally got around to patching the last full ROM today w/ the incremental.
This is the fastbootd w/ flash_all.bat script to update to 11.0.12.12.KB05AA. The package for KB05AA (Global/US) is not yet available, hence I'm still making it available here. Be sure to alter the flash script (remove the "rem" before boot.img and recovery.img if you DO NOT want to keep your custom kernel + TWRP) ****************
3.14 GB file on MEGA
mega.nz
THIS IS ONLY FOR 11.0.9.9.KB05AA, BUT READ IT ANYWAY!!!!: ***************
I think this is the first time anyone has actually made a working incremental update for a rooted OOS device, or any with a payload.bin update method that I know of. This method doesn't require any wiping and TWRP / rooted boot.img / custom OOS kernel can be installed right after the script finishes (or left on the device), and you don't even change your active slot (usually, incremental updates will flash to the inactive slot).
I won't get into that many specifics except it was EXTREMELY DIFFICULT, but it works now. Read here if you want to do it yourself in the future, or on another phone. Should work on just about any phone that uses payload.bin files https://forum.xda-developers.com/t/...11-0-9-9-kb05aa-posted.4314677/#post-85425949
You may have to edit the .bat file to pick your RAM type (the lp5 ones are for devices with LPDDR5; it is preset for most of the phones using the LPDDR4 RAM). On the Op8T at least you can do this from adb shell:
adb shell getprop ro.boot.ddr_type; where a 0 is LPDDR4 and 1 is LPDDR5 ram. If it's 1 returned, you need to flash the lp5 files instead of the same named otherwise files in the .bat file (so edit it).
That weird -cow stuff is temp files that prevented the update from working. Not documented anywhere I could find (well, minimally explained by Google), took hours to figure out they were filling the super partition up. I had to re-engineer a Linux project (linked above) to get this working, and have officially updated from 11.0.8.13 to 11.0.9.9 COMPLETELY now. While rooted, without switching slots, and TWRP installed.
You just have to ensure you're on the latest ADB and Fastboot tools and an adb reboot bootloader, followed by a fastboot reboot fastboot should get you there. You can check with: fastboot getvar is-userspace
If it says yes, you're in fastbootd. It actually will work with TWRP installed, I found out later, as long as you reboot in TWRP to fastboot and confirm with the command above you're in fastbootd.
https://github.com/fawazahmed0/Latest-adb-fastboot-installer-for-windows/releases/tag/v1.7 has a script that will get you the Latest ADB and Fastboot and put it in a folder for you.
I uploaded it to Mega. Just use some common sense and look at the flash_all.bat file before flashing. I'd write more but I'm tired as hell from getting this working. Now we'll never have to wait for an incremental update while rooted again, at least in the foreseeable future.

I'm just going to leave this here
https://forum.xda-developers.com/t/...1-kb2003-kb2005.4178675/page-25#post-85386145

g96818 said:
I'm just going to leave this here
https://forum.xda-developers.com/t/...1-kb2003-kb2005.4178675/page-25#post-85386145
Click to expand...
Click to collapse
That never worked for me and others, Always resulted in either bootloop or booting back to previous build

nujackk said:
That never worked for me and others, Always resulted in either bootloop or booting back to previous build
Click to expand...
Click to collapse
I've mentioned it multiple times for people having issues. They need to use the unbrick tool cause there is something wrong with the original rom install from OnePlus.

g96818 said:
I've mentioned it multiple times for people having issues. They need to use the unbrick tool cause there is something wrong with the original rom install from OnePlus.
Click to expand...
Click to collapse
This Devs solution works and i appreciate his work. And appreciate your attempts but didn't work for me So ....

nujackk said:
This Devs solution works and i appreciate his work. And appreciate your attempts but didn't work for me So ....
Click to expand...
Click to collapse
It's good that you found a band-aid fix.

nujackk said:
That never worked for me and others, Always resulted in either bootloop or booting back to previous build
Click to expand...
Click to collapse
Of course I tried that solution first, it didn't work on my device.
I'm glad it did on others' devices, kudos to you for posting it (and I DO appreciate your work), but this is the only one that worked on mine. Why? Who knows. I also followed another guide that didn't work. Or else I wouldn't have wasted all my time making this (it took many, many hours to assemble). I'm not saying it's the best solution (I really hope someone just uses what I put in the other thread and assembles it into an easier format for others to use), but I have a full time job (2 actually) so I can't work on it anymore. But it works, no data loss, and TWRP can be installed. Until the next incremental update comes out, then I'll post another version using the tools I used for this, if your build doesn't work on my device. But only when I have the time...

g96818 said:
It's good that you found a band-aid fix.
Click to expand...
Click to collapse
LoL band-aid fix... Call it whatever you want, it works.
It's actually a patched 11.0.8.3.KB05AA with the incremental update applied to it for 11.0.9.9.KB05AA. So it flashes to the active slot and TWRP / rooted custom kernel can all be installed at the same time, even while you are still rooted with Magisk, and even if TWRP is installed. No data loss. I never claimed perfection on this project, just that it works for me.
Keep doing what you're doing, I'll keep doing what I'm doing. We both just aim to help others anyway. I just couldn't get any other method to work so I came up with this one, extending on the incomplete / abandoned work of others. I didn't come up with Payload extraction. Never claimed to. I didn't come up with fastbootd flashing either.
All the forked and modified code is at my GitHub repo. The fork goes back to several other devs' forks (mine is the 3rd modified fork).

Someone want to point me to the right download for the incremental update to 11.0.9.9.KB05AA? I got a download link but if it's not for this exact ROM, it would be dangerous (I don't know what would break) if I applied it and patched the incremental 11.0.9.9 (which is like a full ROM in the way I distribute it here). I believe the update is 11.0.10.10.KB05AA. I tried downloading as illustrated in the linked thread and it halfway installed (Op8T's don't seem to like the "remove Magisk images" and then install the update method, it totally jacked up my system (like long boot time, alarms didn't work, numbers wouldn't always appear to login to the phone after reboot, etc.), luckily I had backed up Super in TWRP and that fixed it (upon a restore). The one someone told me was the official link to the incremental update did not work with the Linux program I hacked, so it's either incapable of patching an incremental 2x, or I got the wrong file downloaded. My life is so crazy at the moment I don't have time to screw up my phone just to get the incremental update downloaded on my phone and extract it, so if anyone has already done that, please let me know.

mslezak said:
Someone want to point me to the right download for the incremental update to 11.0.9.9.KB05AA? I got a download link but if it's not for this exact ROM, it would be dangerous (I don't know what would break) if I applied it and patched the incremental 11.0.9.9 (which is like a full ROM in the way I distribute it here). I believe the update is 11.0.10.10.KB05AA. I tried downloading as illustrated in the linked thread and it halfway installed (Op8T's don't seem to like the "remove Magisk images" and then install the update method, it totally jacked up my system (like long boot time, alarms didn't work, numbers wouldn't always appear to login to the phone after reboot, etc.), luckily I had backed up Super in TWRP and that fixed it (upon a restore). The one someone told me was the official link to the incremental update did not work with the Linux program I hacked, so it's either incapable of patching an incremental 2x, or I got the wrong file downloaded. My life is so crazy at the moment I don't have time to screw up my phone just to get the incremental update downloaded on my phone and extract it, so if anyone has already done that, please let me know.
Click to expand...
Click to collapse
Better to install the full ROM
Download Oxygen Updater in app store and select your device AA for global and Ba for European device.
Go to settings, system update wait til 100% and Don't reboot yet if you want to keep Root
Go to Magisk and install ota in inactive slot

5star02707 said:
Better to install the full ROM
Download Oxygen Updater in app store and select your device AA for global and Ba for European device.
Go to settings, system update wait til 100% and Don't reboot yet if you want to keep Root
Go to Magisk and install ota in inactive slot
Click to expand...
Click to collapse
I think maybe you misunderstood what I did in this thread. I patched a full ROM with the incremental update of 11.0.9.9.KB05AA. So while OnePlus does not have a full ROM available for download (yet), it is available for download here.
Yeah the method you propose is the "normal" rooted way, but if you're rooted already it forces you to full ROMs not OTAs. You'll be on 11.0.8.3.KB05AA. The goal here is to get on 11.0.10.10.KB05AA (someone NOT ROOTED could download the OTA update using Oxygen Updater and upload it here so I could make a patched version for those that want to keep their root / custom kernel / TWRP / etc and avoid the hassle of unrooting first, which wipes your data partition). At least my Oxygen Updater won't let me download incremental updates even with Magisk Images removed (don't try this unless you're on Op8 / Op8 Pro; some people are having big system update issues on Op8T incremental hence why this thread exists.) It jacked up my system pretty bad (Magisk images removed, Settings / System / System Updates method) until after a boot.img and super restore from TWRP. Not all devices were setup the same (mine is a US carrier converted to US KB05AA). To my knowledge, no direct download has been posted for KB05AA incremental update. Here or on TG. If you have found one, please post a link here. The only one out I've seen works on European ROMs. OnePlus always does KB05AA last for whatever reason.

11.0.10.10.KB05AA posted with caveats - please back up your data as suggested in case the Phone Services APK doesn't fix your SIM after a flash, and you end up formatting the data partition. You may want to try some other methods or just plan on restoring (not with TWRP Alpha in my experience).

mslezak said:
Guys, bad news. So 11.0.10.10.KB05AA incremental does something to the data partition and kills your SIM access.
...
Click to expand...
Click to collapse
I successfully update from 9.9 to 10.10 including keeping root. I have no issues with my Sim card. So, for me, the update is fine.
However, I believe that the 10.10 update includes a key change. This results in the data partition being unreadable if you swap back to the previous slot after the update. I found this out by doing just that using TWRP.
But syncing the 10.10 firmware to the inactive slot fixes this. It might be possible (I haven't tried it) to just sync the keymaster partition to the inactive slot and then restore 9.9 (excluding keymaster).

BillGoss said:
I successfully update from 9.9 to 10.10 including keeping root. I have no issues with my Sim card. So, for me, the update is fine.
However, I believe that the 10.10 update includes a key change. This results in the data partition being unreadable if you swap back to the previous slot after the update. I found this out by doing just that using TWRP.
But syncing the 10.10 firmware to the inactive slot fixes this. It might be possible (I haven't tried it) to just sync the keymaster partition to the inactive slot and then restore 9.9 (excluding keymaster).
Click to expand...
Click to collapse
Can you explain how you managed to update it? I'm screwed at this point anyhow, would like to hear how you did it. Are you just saying when you update flash to both slots and the data is still readable? Instead of flashing to active only? I still have the extracted / patched ROM, not going to try it out now (or for a while) unless I know someone has figured out a way to make it not break the system data. (Note: I'm on a very hacked phone; it's a carrier T-mobile originally fastbootd converted to Global, then updated on Global since then). I realize most people probably don't have a phone that's been altered this much. Then the easier methods are more likely to work. I'm also running a custom fork (mine) of RadioActive kernel (just tweaked how I like it, wakelocks blocked to save idle battery, some GPU frequencies added, etc). I tried running just the patched boot.img with Magisk but still Phone Services was busted.

@mslezak, When I get an update I:
- use a terminal session (you could also use ADB) to restore the stock boot and recovery (this way I don't lose root yet)
- install the update but don't reboot
- copy the new boot image and patch it
- turn on airplane mode (to avoid SafetyNet and certification issues in the next step)
- reboot the phone and the updated system comes up
- flash the patched boot image and TWRP in fastboot/bootloader
- reboot and disable airplane mode
This is basically @osm0sis' process from https://forum.xda-developers.com/t/...ices-platforms.2239421/page-149#post-84764713
No, I'm not saying flash to both slots, because that will make it impossible to fall back to the current system if the update fails (though this is meaningless if you're manually flashing partitions).
I've got into the habit of syncing active to inactive (after I'm happy with the update) simply because it's required when going from OOS to a custom ROM (I use a shell script based on the LineageOS sync zip). And, after the sync, I can now access the data partition from the inactive slot (which wasn't the case just after the update due to the different keys).

mslezak said:
Can you explain how you managed to update it? I'm screwed at this point anyhow, would like to hear how you did it. Are you just saying when you update flash to both slots and the data is still readable? Instead of flashing to active only? I still have the extracted / patched ROM, not going to try it out now (or for a while) unless I know someone has figured out a way to make it not break the system data. (Note: I'm on a very hacked phone; it's a carrier T-mobile originally fastbootd converted to Global, then updated on Global since then). I realize most people probably don't have a phone that's been altered this much. Then the easier methods are more likely to work. I'm also running a custom fork (mine) of RadioActive kernel (just tweaked how I like it, wakelocks blocked to save idle battery, some GPU frequencies added, etc). I tried running just the patched boot.img with Magisk but still Phone Services was busted.
Click to expand...
Click to collapse
Thats not very hacked/hacked at all, and quite a few use that setup

xstefen said:
Thats not very hacked/hacked at all, and quite a few use that setup
Click to expand...
Click to collapse
LoL I gave up fastbootd flashed to 11.0.10.10.KB05AA and formatted data, let Google download everything it backed up, and am back in business. Just have a lot of apps to login to / Magisk modules to add / etc.
So yeah my patched 11.0.10.10.KB05AA works but the data must be formatted or the SIM doesn't work (at least for me; I don't know if anyone else has tried it since I just posted it a few hours ago; it could be that it works for some without causing issues, I don't have any idea). The goal was to not have to mess up the data partition.... but I can't control what OnePlus does in their updates... Try what worked for others posted here first I'd suggest, or just make solid backups of everything knowing you're going to likely need to reinstall / re-login to everything and format the data partition. New pin, new fingerprint, etc. Re-login to your wifi blah blah.
It's still a full unreleased ROM so I posted it for those that don't mind taking backups (outside of TWRP) if they want to keep root & TWRP on the new release... Yeah a pain to setup if you aren't warned to use another backup method (maybe there is a better backup method, maybe Migrate (app store early access) is developed enough for easy transfer now, I know many people said it worked well in the past but haven't been following the updates. Still free).

It dawned on me later that since the only thing that didn't work using this method going from 11.0.9.9.KB05AA to 11.0.10.10.KB05AA was phone services, that I should just include the working version in this post. Since I already did it the hard way and restored everything back to normal. AS I SAID ABOVE, IF PHONE SERVICES ISN'T ENOUGH TO FIX THE ISSUE, PM ME AND I CAN EXTRACT MORE RELATED FILES UNTIL IT WORKS AGAIN. Unfortunately, I can't just downgrade to 11.0.9.9.KB05AA and keep trying fastbootd over and over again as I don't have the time.

g96818 said:
I've mentioned it multiple times for people having issues. They need to use the unbrick tool cause there is something wrong with the original rom install from OnePlus.
Click to expand...
Click to collapse
The whole point of this is to AVOID the unbrick tool, reinstalling an outdated version, updating each new ROM build since the brick tool was made, and starting over clean. I think... Have a hunch at least we're almost there on 11.0.10.10.KB05AA with an APK install... Although just backing up everything first will always work (if you don't mind formatting your data partition) just as it's posted here already. Always an issue for us rooted users (especially on Global) since we're always last in line to get a full ROM. This IS a full ROM, payload extracted and patched with incremental updates. Still not available from OnePlus Global (KB05AA) as I checked today, so still relevant.

Ladies and Gents,
I have removed some off topic posts from this thread because I believe we could express the same meaning in more civil words. Please try to do that from now on.
Thanks.
Jerry
FSM