Your dreams are now reality!
You can install Nougat easily on your Galaxy s7 edge!!
1)Download Odin 3.12.3 .zip file and run/open Odin3 v3.12.3.exe file from the extracted files on your PC.
2)Download the Nougat firmware for your device from the downloads section above, and unzip the .zip file to get the files starting with AP, CSC, Home_CSC, BL and CP in the beginning of their name.
3)Enable OEM unlock on your phone:
Go to Settings » About phone » and tap Build number seven times to enable Developer options.
4)Go back to main Settings page, scroll to bottom and select Developer options from there.
Under Developer options, look for Enable OEM unlock checkbox/toggle and enable it.
5) Boot your device into Download mode:
Switch off your device.
Press and hold “Home + Power + Volume down” buttons for a few seconds until you see a warning screen.
Press Volume Up on the warning screen to accept it and boot into Download mode.
6) Once your device is in download mode, connect it to the PC with a USB cable. The Odin window on PC should detect the device and show an “Added!!” message.
7) Now we’ll select each firmware file (from files we got in Step 2 above) into the appropriate box in Odin.
Click on CSC tab and select the firmware file starting with HOME_CSC in its name.
└ Note: Do NOT select the regular CSC file that starts with CSC in its name, as that would replace your CSC and thus would result factory data reset of the device.
Click on CP tab and select file starting with CP in its name.
Click on BL tab and select the file starting with BL in its name.
Click on AP tab and select the file starting with AP in its name.
└ Note: DON’T play with any other options on Odin the screen. You’re only required to connect your device and select the firmware files as instructed above.
Click the Start button on Odin and wait for it to finish the process. Once it has finished successfully, you’ll see a pass message on the Odin screen.
8) Your device will automatically reboot when Odin is done flashing. You can then disconnect your device.
└ It might take some time for the first boot after flashing a stock firmware.
That’s it. Your Galaxy S7/Galaxy S7 Edge is now rocking Android Nougat update.
9) enjoy
-------------
download section
-------------
Odin : http://www.theandroidsoul.com/download-odin/
firmware : http://downloadmirror.co/Vm1/BTU-G930FXXU1DPLT-20170117160813.zip
Source : http://www.theandroidsoul.com/download-galaxy-s7-and-s7-edge-nougat-firmware-odin-tar/
As per my reply to you in the S7E forum, there's a dedicated thread for Nougat: https://forum.xda-developers.com/galaxy-s7/how-to/samsung-s7-nougat-final-ota-t3532213
Related
I found it a crazy effort to download this file, but here it is if you want it on dropbox.
https://www.dropbox.com/s/uwdbdchoy4l1ya6/BTU-T713XXU2APJ1-20161019134656.zip?dl=1
This is for UK Region and version 6.0.1.
Source: https://samsung-firmware.org/model/SM-T713/region/BTU/
Flashing guide:
1. Download above firmware.
2. Open Odin Tool. (http://odindownload.com/) version 3.12.3 worked for me.
3. Boot your device in the "Download Mode":
Press Volume Down, Power and Home buttons at same time for 5-8 seconds until download mode is active.
4. Connect your device to PC via the USB cable while in download mode.
5. Next, check the "Auto Reboot" and "F. Reset Time" options in Odin Tool.
6. Hit the AP/PDA button then browse and select a tar.md5 file from the extracted folder.
7. Finally press the start button to begin flashing the firmware update on your device.
Followed all steps to root phone.
But odin displays Fail (Auth) error. Not sure how to root my phone
Hello. I did root my phone few days ago using Odin, I can help you.
What do you need:
SuperSU ZIP File (For your Android version, to check in Settings -> About device) and copy it to phone memory
TWRP Recovery MD5 File (for Odin) (for your phone model, check in Settings -> About device)
Now steps:
1. Enable OEM Unlock in Developer Options (If not unlocked, Settings -> About device -> Tap "Build Number" 7 times)
2. Open Odin and select AP (maybe PDA)
3. Find your TWRP File and select it
4. Turn off your phone, go to Download Mode (Volume Down, Home and Power buttons), click Volume Up (once)
5. Connect your device to your PC (In Download Mode you need to see Odin Mode!)
6. If in Odin you have seen "Added!" click Start
7. If Odin will fail, try again (I needed to)
8. If you have already flashed TWRP, go to it (Volume Up, Home and Power buttons)
9. Go to Wipe option and swipe to do default wipe.
10. Now click Install, select your SuperSU file.
11. Swipe to do it (Zip authentication disabled!!!!)
12. After it's done, reboot your phone again to your OS.
13. Enjoy your new root!
Optional Step: download Root Checker from Google Play and check your root.
I hope I did help you.
Hello everyone! I made a tutorial regarding flashing the latest updates:
1. Download and extract both Frija and Odin.
2. Launch Frija.
3. Check the "Auto" button. Write your device's Model Number and CSC
(Your model number is at Settings, then About phone).
4. Click on "Check Update".
5. Click on "Download" and choose a folder to save the firmware.
6. After the download is complete, extract the firmware .zip.
7. Launch Odin.
8. Click the "BL" button and select the file that starts with "BL_...".
9. Click the "AP" button and select the file that starts with "AP_...".
10. Click the "CP" button and select the file that starts with "CP_...".
11. Click the "CSC" button and select the file that starts with "HOME_CSC_..." (Selecting CSC_... will wipe your data!).
12. Turn off your phone.
13. Boot into Download Mode by holding both Volume Up + Volume Down buttons and then connecting it to your PC.
14. After booting into Download Mode, press the Volume Up button to continue.
15. Back to Odin, click "Start".
16. The flashing process will be over when "PASS" is shown in Odin and your phone reboots. You may close Odin and disconnect the phone from your PC then.
17. Congrats! You have successfully flashed the latest update to your device.
18. After your phone is on, turn it off again.
19. Boot into Recovery Mode by connecting to your PC and holding Volume Up + Power Button (+ Bixby Button).
20. Navigating with the Volume Buttons and selecting with the Power Button, go to "Wipe cache partition".
21. Select "Yes".
22. Select "Reboot system now".
Links:
Odin 3 by Samsung:
Index of /samsung-tools/
Frija by invmini:
[Tool] Frija - Samsung firmware downloader/checker
* * * PLEASE UNDERSTAND WHAT YOU ARE INSTALLING TO YOUR DEVICES AT ALL TIMES AND ME AND THE DEVELOPER ARE NOT RESPONSIBLE FOR ANY SORT OF DAMAGE TO YOUR DEVICE * * * Hey Guys :) Frija is a new tool (successor of now depreciated tool SamFirm)...
forum.xda-developers.com
CSCs Cheat Sheet:
List of Samsung Galaxy CSC Country Specific Product code and region they belong to
List of CSC Country Specific code for Samsung Galaxy & various countries, regions, network carriers, model numbers, variants phone belong to.
www.androidsage.com
I hope it helps you!
Hello everyone! I made a tutorial regarding flashing the latest updates:
Spoiler: Video
1. Download and extract both Frija and Odin.
2. Launch Frija.
3. Check the "Auto" button. Write your device's Model Number and CSC
(Your model number is at Settings, then About phone).
4. Click on "Check Update".
5. Click on "Download" and choose a folder to save the firmware.
6. After the download is complete, extract the firmware .zip.
7. Launch Odin.
8. Click the "BL" button and select the file that starts with "BL_...".
9. Click the "AP" button and select the file that starts with "AP_...".
10. Click the "CP" button and select the file that starts with "CP_...".
11. Click the "CSC" button and select the file that starts with "HOME_CSC_..." (Selecting CSC_... will wipe your data!).
12. Turn off your phone.
13. Boot into Download Mode by holding both Volume Up + Volume Down buttons and then connecting it to your PC.
14. After booting into Download Mode, press the Volume Up button to continue.
15. Back to Odin, click "Start".
16. The flashing process will be over when "PASS" is shown in Odin and your phone reboots. You may close Odin and disconnect the phone from your PC then.
17. Congrats! You have successfully flashed the latest update to your device.
18. After your phone is on, turn it off again.
19. Boot into Recovery Mode by connecting to your PC and holding Volume Up + Power Button (+ Bixby Button).
20. Navigating with the Volume Buttons and selecting with the Power Button, go to "Wipe cache partition".
21. Select "Yes".
22. Select "Reboot system now".
Links:
Odin 3 by Samsung:
Index of /samsung-tools/
Frija by invmini:
[Tool] Frija - Samsung firmware downloader/checker
* * * PLEASE UNDERSTAND WHAT YOU ARE INSTALLING TO YOUR DEVICES AT ALL TIMES AND ME AND THE DEVELOPER ARE NOT RESPONSIBLE FOR ANY SORT OF DAMAGE TO YOUR DEVICE * * * Hey Guys :) Frija is a new tool (successor of now depreciated tool SamFirm)...
forum.xda-developers.com
CSCs Cheat Sheet:
List of Samsung Galaxy CSC Country Specific Product code and region they belong to
List of CSC Country Specific code for Samsung Galaxy & various countries, regions, network carriers, model numbers, variants phone belong to.
www.androidsage.com
I hope it helps you!
Thats great effort, thanks mate, cheers.
Guide for Flash Firmware (Use Odin in zip file):
Link Mega for No WIPE version+Odin 3.14.4:
File on MEGA
mega.nz
1. Open Odin;
2. Click the BL button and select the file BL ****;
3. Click on the AP button and select the file AP ****;
4. Click on the CP button and select the file CP ****;
5. Click on the CSC button and select the file HOME_CSC ****;
6. Now enter in Download Mode (from the phone off, hold down the volume up key and the power on/off key a the same time and left key when you see the Samsung logo);
7. You will find yourself in front of recovery menu screen where you will be choice with the Volume key button "reboot to bootloader";
8. connect cable to PC and to the device and wait to be recognized by Odin (The ID: COM box will change color and 0 will appear: COM6 or other number);
9. Click Start;
10. The operation will last a few minutes (usually 5-10 minutes). At the end the device will restart itself to complete some operations;
Greetings
Ciccio80
P.S. I downloaded the original files via samfirm - tested and working on my ITV S20.