Hi all,
After reading on letv.re that some people managed to brick their devices and were looking for a fix, I started to check more and more about the issue. What happened to some was that the phone would switch itself off and enter into Qualcomm Recovery Mode and would be seen when connected to a computer as “Qualcomm HS-USB QDLoader 9008”. For others, by flashing wrong files the phone would end up in the same state. Luckily a fix had been found, and it was shared by ParasiTe_RemiX.
DISCLAIMER
Given that maybe nothing will happen to your warranty and this is an unbricking tool, there are small chances that your device might get bricked for good, and I feel the need to say that I am not responsible for any damage caused by following these instructions. Any modification that you do to your phone you're doing at your OWN RISK.
Keep in mind that if your phone goes by itself in the QDLoader mode, it’s better to try some combinations below before flashing it using this method:
1) Keep the power button pressed for about 2 minutes, or
2) Keep the power button + Vol up pressed for about 2 minutes, or
3) Keep the power button while connecting the phone to a wall charger, or
4) Bring the phone into a bright light and press the power button (or power button + Vol up) for about 2 minutes, or
5) Keep the phone charging for more than 24 hours and repeat all the steps above.
If nothing works and you are willing to fix it and you’ll give up all your files, then this fix is for you. Or if you have flashed some wrong files and there is no Fastboot, nor Recovery, this is to be followed. Or if you want to reset your phone to a “factory state”, this is the way to go, and by that I mean if you want to check that your fingerprint sensor is working, or you have some other issues, it’s good to revert it this way.
What you will need:
a) A Windows computer
b) FlashOne program - the flashing program for the software
c) QFIL files for X820 (looks like some dev software dating April,2016)
IMPORTANT – YOU WILL LOSE ALL YOUR FILES ON THE PHONE, PHOTOS, MUSIC, APP DATA, INTERNAL STORAGE WILL BE WIPED.
So if your phone is in this Qualcomm Recovery mode, you can just connect it to the computer, and jump to step 3, if not, and you simply want to flash it, start from step 1.
1) To enter Qualcomm Recovery mode, first turn off the phone and go to step 2
2) Keep pressed Vol Up (+) and Vol Down (-) together and connect the phone by USB cable to the computer.
3) You will see that the computer will install drivers for "Qualcomm HS-USB QDLoader 9008".
4) Unzip FlashOne and start "main.exe". Once you've opened the flashtool you'll see "Flash Type". Here select "Qualcomm - flash dead phone".
5) Select your phone - "COM ..." from "Select device" - here should be the same COM ... as it shown in Device Manager under Ports (COM & LPT) > "Qualcomm HS-USB QDLoader 9008 (COM ...)"
6) Select File "LeMax2QFIL.zip" from the folder where it is saved
7) Press "Flash" in the lower part of the window
8) Once completed, disconnect the phone and power it up
9) Go to Settings – Storage format the internal storage.
To exit the Qualcomm Recovery mode, keep the Power Button pressed for about 1 minute or until the phone will vibrate and restart into system.
That's it. More info you will find in FlashOne program, actually it's almost like I've described it here.
You will be reverted to a "dev" version of the phone, somewhere with April build date. Keep in mind that it's EUI 5.6 and the kernel is different than EUI 5.8. Update it to latest EUI with stock recovery and then install the custom recovery of your choice.
Most of the guys install a recovery for 5.6 on EUI 5.8 or vice versa and then they get the blue LED. That's why you should read the instructions for each recovery and make sure you know which one you're flashing.
Download files:
Mega:
https://mega.nz/#F!0gwgxbxD!-iud2O-6uZ0F3Geofz-NyA
Google Drive:
FlashOne:
FlashOne1.9.zip
drive.google.com
QFIL:
Lemax2QFIL.zip
drive.google.com
TWRP: https://forum.xda-developers.com/le-max-2/development/twrp-root-14s-rom-x820-t3382221
https://mega.nz/#!Jl4DATLI!Z08l-0SWc98C1qUGDEOcTsj96DlY627B7nHtlKCp6qw
https://mega.nz/#!slYmEJ6K!Onc5pjb3teB9J6AunZnEe-k6mDJwQ2tQwUt0X51AudI
Stock Recovery (not tested) and needs an EUI ROM to be instaled as update.zip:
https://mega.nz/#!B0ZGgSQB!33UG9jpEL6b_zJm4M01yRpI0x4uHA4Q1XzaS0ntXVSI
Edit: Post updated.
Thanks
Hi
First of all I want to thank you for posting this solution. Yesterday I managed to solve it too but it took me a while to find all this info.
Now I have ran into annother problem, I am not able to flash any rom from the stock recovery, it says "file corrupted" every time.
Any solution to this?
rapiteu said:
Hi
First of all I want to thank you for posting this solution. Yesterday I managed to solve it too but it took me a while to find all this info.
Now I have ran into annother problem, I am not able to flash any rom from the stock recovery, it says "file corrupted" every time.
Any solution to this?
Click to expand...
Click to collapse
Honestly, I did this restoration of the phone about a month ago. I encountered some issues with the stock recovery but I can't remember what I did to fix it. I think I installed 017s at that time, directly from the dev software. Restarting the phone to recovery I think didn't work. I believe you should turn it off and then start it to recovery directly. I remember I wanted to download 015s, 016s, and even I gave up and wanted to install TWRP for 5.6 EUI but the stock recovery at some point worked. Try to turn off the phone (not restart) and then switch on in recovery. And check erase data as well.
valy_cta said:
1) To enter Qualcomm Recovery mode, turn off the phone. Keep pressed vol up and vol down and turn on the device by pushing the power button.
Click to expand...
Click to collapse
Hello, I just wanted how does it look to see the phone in its normal state but cannot switch it on againg form normal opration. Is there eny key combination. It looks like bricked just now
regard Filozof71
OK, it works. Need press power button ober one minute. Uff
Leeco X910 brick
Hello, my leeco x910 is bricked...
Black screen, no led, no sound nothing just usb connection is ok for flashing 9008 mode..
Is possible to obtain the good .mbn file for flashing?
Please help me
Best regards
valy_cta;69439085
1) To enter Qualcomm Recovery mode said:
Hello, I'm on Windows 7, I enter #3 point above but I can see only QUSB_BULK device under devices manager but Windows 7 does not have any drivers for it. I tried to dwonload some but withous success. Has anybody runover rhis instruction? Uder which Windows version?
OK. Under Windows 10 it works means it installs the phone as Qualcomm HS-USB QDLoader 9008 and its visible in FlashOne program.
Great appreciation to valy_cta!
regards Filozof71
Click to expand...
Click to collapse
Problem
My phablet give me problem.
Log:
13: c:\FlashOne1.9\Lemax2QFIL\prog_ufs_firehose_8996_ddr.elf
19:17:45: ERROR: function: sahara_rx_data:194 Unable to read packet header. Only read 0 bytes.
19:17:45: ERROR: function: sahara_main:854 Sahara protocol error
19:17:45: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
what am I doing wrong?
slawin wynterz said:
My phablet give me problem.
Log:
13: c:\FlashOne1.9\Lemax2QFIL\prog_ufs_firehose_8996_ddr.elf
19:17:45: ERROR: function: sahara_rx_data:194 Unable to read packet header. Only read 0 bytes.
19:17:45: ERROR: function: sahara_main:854 Sahara protocol error
19:17:45: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
what am I doing wrong?
Click to expand...
Click to collapse
The link of this file is corrupted, you could post the site link. where the file is. I'm grateful.
link
bruno araujo said:
The link of this file is corrupted, you could post the site link. where the file is. I'm grateful.
Click to expand...
Click to collapse
drive.google.com/drive/folders/0BzteXVVFgQLpZndPRmhDNDJiXzg
UP
UP
slawin wynterz said:
drive.google.com/drive/folders/0BzteXVVFgQLpZndPRmhDNDJiXzg
Click to expand...
Click to collapse
slawin wynterz said:
UP
Click to expand...
Click to collapse
He fixed his phone finally.
OP updated.
slawin wynterz said:
drive.google.com/drive/folders/0BzteXVVFgQLpZndPRmhDNDJiXzg[/QUOTE
thank you, now I could install clean ROM
Click to expand...
Click to collapse
hard brick LeEco Le Max 2
hello,
thanks for the guide,
I installed the Lemax2QFIL but then
I can not istall any rom.
I renamed the various rom in update but the system responds file corrupted every time.
beachboys1970 said:
hello,
thanks for the guide,
I installed the Lemax2QFIL but then
I can not istall any rom.
I renamed the various rom in update but the system responds file corrupted every time.
Click to expand...
Click to collapse
Reboot phone, after power on one time flash it.
Did you find a fix for this? I am struggling with Lemax x910
slawin wynterz said:
My phablet give me problem.
Log:
13: c:\FlashOne1.9\Lemax2QFIL\prog_ufs_firehose_8996_ddr.elf
19:17:45: ERROR: function: sahara_rx_data:194 Unable to read packet header. Only read 0 bytes.
19:17:45: ERROR: function: sahara_main:854 Sahara protocol error
19:17:45: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
what am I doing wrong?
Click to expand...
Click to collapse
Hi,
Did you find a fix for this? It seems like you resolved the error somehow. Would you be willing to share how you did that please? I would be extremely grateful. I continue to see the above errors as well.
---------- Post added at 03:27 AM ---------- Previous post was at 03:22 AM ----------
valy_cta said:
He fixed his phone finally.
OP updated.
Click to expand...
Click to collapse
Do you know how he fixed it? I also continue to see the exact same error on the lemax pro x910 and I have pretty much exhausted my options at this point in time. Your help would be extremely appreciated.
the error that I see is as follows:
13: c:\FlashOne1.9\Lemax2QFIL\prog_ufs_firehose_8996_d dr.elf
19:17:45: ERROR: function: sahara_rx_data:194 Unable to read packet header. Only read 0 bytes.
19:17:45: ERROR: function: sahara_main:854 Sahara protocol error
19:17:45: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
bil20 said:
Hi,
Did you find a fix for this? It seems like you resolved the error somehow. Would you be willing to share how you did that please? I would be extremely grateful. I continue to see the above errors as well.
---------- Post added at 03:27 AM ---------- Previous post was at 03:22 AM ----------
Do you know how he fixed it? I also continue to see the exact same error on the lemax pro x910 and I have pretty much exhausted my options at this point in time. Your help would be extremely appreciated.
the error that I see is as follows:
13: c:\FlashOne1.9\Lemax2QFIL\prog_ufs_firehose_8996_d dr.elf
19:17:45: ERROR: function: sahara_rx_data:194 Unable to read packet header. Only read 0 bytes.
19:17:45: ERROR: function: sahara_main:854 Sahara protocol error
19:17:45: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
Click to expand...
Click to collapse
Reboot phone (long press volume "-"), after power on (long press volume "+" "-" and power) and just one time flash it.
bil20 said:
Hi,
Did you find a fix for this? It seems like you resolved the error somehow. Would you be willing to share how you did that please? I would be extremely grateful. I continue to see the above errors as well.
---------- Post added at 03:27 AM ---------- Previous post was at 03:22 AM ----------
Do you know how he fixed it? I also continue to see the exact same error on the lemax pro x910 and I have pretty much exhausted my options at this point in time. Your help would be extremely appreciated.
the error that I see is as follows:
13: c:\FlashOne1.9\Lemax2QFIL\prog_ufs_firehose_8996_d dr.elf
19:17:45: ERROR: function: sahara_rx_data:194 Unable to read packet header. Only read 0 bytes.
19:17:45: ERROR: function: sahara_main:854 Sahara protocol error
19:17:45: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
Click to expand...
Click to collapse
I don't think that you can flash a X910 with X820 files, although I never tried and never heard someone to do so, the results might not be too good.
That error was due to the fact that he was not pressing the buttons properly before connecting to computer. Keep Vol up and Vol down and connect the phone. It should be switched off before.
Good luck!
Thanks very much
How would I switch off a hard bricked device? Every time I connect the device, the device manager shows that it's been connected "Qualcomm ------ 90008" so how would I turn it off , especially if the battery is embedded?
Can you press the power button for at least 1 minute?
If you have it connected and it shows in computer as Qualcomm... 9008, it's ok. Maybe the files are detected as not being for your phone.
If you suddenly found the phone in such way and you didn't flash something that broke it, try to restart it as shown in the op. If not, try to discharge the battery fully that to flash something that it doesn't belong.
bil20 said:
How would I switch off a hard bricked device? Every time I connect the device, the device manager shows that it's been connected "Qualcomm ------ 90008" so how would I turn it off , especially if the battery is embedded?
Click to expand...
Click to collapse
I just long press button "-" and it diconnected after 15-20 sec.
Related
Hi,
I had updated my oneplus two with cyanogenmod 13 successfully. I had been running this for more than 5 months.
Yesterday i had downloaded an update of CM13 and was trying to install the update, the phone just went blank with a black screen so i restarted the phone. Since then the phone is not loading into the OS, when i try restarting the phone the oneplus logo screen just flashes and then the phone just displays black screen or switches off.
I am not able to enter into recovery mode which is the biggest problem i am facing due to which i am not able to even perform other recovery options.
I connect the phone to computer using usb and when i use any command such as adb devices, i dont see any device in the list. i get error: no devices when i use other adb commands.
I tried using QFIL from quallcom, but i get the below error when i click the download button:
Process Index:0
Programmer Path:E:\8675_W00\prog_emmc_firehose_8936.mbn
Image Search Path:E:\8675_W00
Please select the XML file
Invalid image search path, ignored
Start Download
Program Path:E:\8675_W00\prog_emmc_firehose_8936.mbn
COM Port number:11
Sahara Connecting ...
Sahara Version:0
Start Sending Programmer
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
---------------------------------------
Please help me in unbricking the oneplus two.
Solved?
Hi md vasi, you can try the methond on the oneplus community search for "unbrick Oneplus 2", choose "[Q&A] The Ultimate OnePlus 2 Guide - Solutions e.t.c.", go to "how to unbrick".
I've also a bricked OP2 that has same issues as yours, happened exactly the same way it happened to you but while updating Resurrection Remix Mod. I've unfortunately not managed to unbrick my device. Hope you it will work for you, please follow the procedure step by step and keep me posted if you can unbrick your OP2 and tell me how you did it. Ok?
Good luck buddy:good:
axaman943 said:
Hi md vasi, you can try the methond on the oneplus community search for "unbrick Oneplus 2", choose "[Q&A] The Ultimate OnePlus 2 Guide - Solutions e.t.c.", go to "how to unbrick".
I've also a bricked OP2 that has same issues as yours, happened exactly the same way it happened to you but while updating Resurrection Remix Mod. I've unfortunately not managed to unbrick my device. Hope you it will work for you, please follow the procedure step by step and keep me posted if you can unbrick your OP2 and tell me how you did it. Ok?
Good luck buddy:good:
Click to expand...
Click to collapse
were you able to unbrick your OPT?
phorcus said:
were you able to unbrick your OPT?
Click to expand...
Click to collapse
Yep, the most important is that you find the right driver for Snapdragon 810, i can't recall where i found the link, it took me a while, wait... i got it, i've found the right driver's link on a website named Android brick or something, with the right driver the flash tool from OP2 will recognise your device and flash stock build.
good luck
axaman943 said:
Yep, the most important is that you find the right driver for Snapdragon 810, i can't recall where i found the link, it took me a while, wait... i got it, i've found the right driver's link on a website named Android brick or something, with the right driver the flash tool from OP2 will recognise your device and flash stock build.
good luck
Click to expand...
Click to collapse
gfil is giving me this error:
COM Port number:5
Sahara Connecting ...
Sahara Version:0
Start Sending Programmer
Download Fail:Unable to download Flash Programmer using Sahara Protocol
Download Fail:Sahara FailSahara Fail
Finish Download
and msm tool is also giving me error but since its in chinese i cannot understand them, do you have any other ways to unbrick OPT
so i havent had any luck posting in other thread and since so many people are asking about this error i thought having its own thread may get some help. I bricked my letv x800 when the rooted phone failed to install a custom rom, stop half way through with corrupted file msg then went dead. I used w w w droidsavvy.com/unbrick-qualcomm-mobiles/ and followed the steps there but for the life i me i cannot get past this step of dl using qfil. I am hoping someone on the boards can give me some idea i spent a week trying to find a way to get past this step and all i find is others stuck on same step with no solution.
Here is the log file of the process. Using Win 7 pro. I got the latest drivers for qfil installed and it finds the phone and asigns the port ok. I just cant download the protocol
Start Download
Program Path:C:\Users\sharkattackproducts\Downloads\QFIL_X800_HARD_BRICK_FIX\x1_na_dvt1_fastboot\prog_emmc_firehose_8994_ddr.mbn
COM Port number:5
Sahara Connecting ...
Sahara Version:0
Start Sending Programmer
Download Fail:Unable to download Flash Programmer using Sahara Protocol
Download Fail:Sahara FailSahara Fail
Finish Download
Sharkattackp said:
so i havent had any luck posting in other thread and since so many people are asking about this error i thought having its own thread may get some help. I bricked my letv x800 when the rooted phone failed to install a custom rom, stop half way through with corrupted file msg then went dead. I used w w w droidsavvy.com/unbrick-qualcomm-mobiles/ and followed the steps there but for the life i me i cannot get past this step of dl using qfil. I am hoping someone on the boards can give me some idea i spent a week trying to find a way to get past this step and all i find is others stuck on same step with no solution.
Here is the log file of the process. Using Win 7 pro. I got the latest drivers for qfil installed and it finds the phone and asigns the port ok. I just cant download the protocol
Start Download
Program Path:C:\Users\sharkattackproducts\Downloads\QFIL_X800_HARD_BRICK_FIX\x1_na_dvt1_fastboot\prog_emmc_firehose_8994_ddr.mbn
COM Port number:5
Sahara Connecting ...
Sahara Version:0
Start Sending Programmer
Download Fail:Unable to download Flash Programmer using Sahara Protocol
Download Fail:Sahara FailSahara Fail
Finish Download
Click to expand...
Click to collapse
I had the same issue when i first bricked my x800 and the problem was that the bootloader was locked somehow. I unlocked then everything went smooth. I don't know if this is the issue here with you.
how do i unlock the bootloader?
from what i can find to unlock bootloaded you need to install stuff onto the phone, atm i cant do that.
Sharkattackp said:
from what i can find to unlock bootloaded you need to install stuff onto the phone, atm i cant do that.
Click to expand...
Click to collapse
i have the same problem
i am tring this program now
https://forum.hovatek.com/thread-12405.html
in 10 minutes i will tell you if it worked
Sharkattackp said:
how do i unlock the bootloader?
Click to expand...
Click to collapse
You do it trough adb and fastboot. You don't have to install anything onto the phone. Just put the phone in fastboot mode, then connect to adb and write : fastboot oem unlock
attitude12 said:
You do it trough adb and fastboot. You don't have to install anything onto the phone. Just put the phone in fastboot mode, then connect to adb and write : fastboot oem unlock
Click to expand...
Click to collapse
when the phone is bricked there is no such thing as fastboot..
the program didn't fuction but managed to install drivers that enabled to qfil to go further in the process but still failed..
twd123 said:
when the phone is bricked there is no such thing as fastboot..
the program didn't fuction but managed to install drivers that enabled to qfil to go further in the process but still failed..
Click to expand...
Click to collapse
yea what he said
can you send me a direct link to that program, all i got was one in chinese
Sharkattackp said:
can you send me a direct link to that program, all i got was one in chinese
Click to expand...
Click to collapse
in the link that i send you it shows the process to change to english.
Sharkattackp said:
can you send me a direct link to that program, all i got was one in chinese
Click to expand...
Click to collapse
i did it ! yeah
install the drivers that come with that program
go to the folder that has the rom, click on its properties- permissions and select full acess
while with qfil open, hold the volume down on the smarthphone and connect it to the pc.only release the volume- when you hear 3 windows sounds(one sound when you connect and two after 15 seconds) . start download and then you are set.
after this process your phone will be alive, but will have only 10gb so you have to follow the process in page 3 of topic "hard brick fix"
hope it helps
have a good day
To Sharkattackp:
Did you get any luck?
Sharkattackp said:
so i havent had any luck posting in other thread and since so many people are asking about this error i thought having its own thread may get some help. I bricked my letv x800 when the rooted phone failed to install a custom rom, stop half way through with corrupted file msg then went dead. I used w w w droidsavvy.com/unbrick-qualcomm-mobiles/ and followed the steps there but for the life i me i cannot get past this step of dl using qfil. I am hoping someone on the boards can give me some idea i spent a week trying to find a way to get past this step and all i find is others stuck on same step with no solution.
Here is the log file of the process. Using Win 7 pro. I got the latest drivers for qfil installed and it finds the phone and asigns the port ok. I just cant download the protocol
Start Download
Program Path:C:\Users\sharkattackproducts\Downloads\QFIL_X800_HARD_BRICK_FIX\x1_na_dvt1_fastboot\prog_emmc_firehose_8994_ddr.mbn
COM Port number:5
Sahara Connecting ...
Sahara Version:0
Start Sending Programmer
Download Fail:Unable to download Flash Programmer using Sahara Protocol
Download Fail:Sahara FailSahara Fail
Finish Download
Click to expand...
Click to collapse
Hi guys. I have this problem with my lenovo phab pb1 750m. My phon is hard bricked and dead . Each time i try to flash it using qfil i get error massage saying : sahara fail, unable to download flash programmer using sahara protocol
Does anybody know what is this sahara protocol and how to fix it. I want to know is my phone fixable in this state or not. And by the way how unlocking bootloader is done?. Please help me
Here is a direct link to my Gdrive w/ the zip/files needed along with simple directions for unbricking Le Pro 1:
https://drive.google.com/drive/folders/0B_wgOh28vwZudWktTnBncTNrNTg?usp=sharing
Tahsin1368 said:
Hi guys. I have this problem with my lenovo phab pb1 750m. My phon is hard bricked and dead . Each time i try to flash it using qfil i get error massage saying : sahara fail, unable to download flash programmer using sahara protocol
Does anybody know what is this sahara protocol and how to fix it. I want to know is my phone fixable in this state or not. And by the way how unlocking bootloader is done?. Please help me
Click to expand...
Click to collapse
Hi, you could fix your phone that has the hard brick?
I have a lenovo k5 that have hard brick right now and cant fix it
ls 4503
Same problem here on my lyf ls 4503??
cant solve pls help
twd123 said:
i have the same problem
i am tring this program now
https://forum.hovatek.com/thread-12405.html
in 10 minutes i will tell you if it worked
Click to expand...
Click to collapse
Which file to be download for Cool dual C106? Please help me.
Lenovo Vibe K5
I getting this error:
12:19:09: ERROR: function: sahara_rx_data:237 Unable to read packet header. Only read 0 bytes.
12:19:09: ERROR: function: sahara_main:924 Sahara protocol error
12:19:09: ERROR: function: main:303 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
I know it is not the right place but if you know how to fix it
Stormbg said:
I getting this error:
12:19:09: ERROR: function: sahara_rx_data:237 Unable to read packet header. Only read 0 bytes.
12:19:09: ERROR: function: sahara_main:924 Sahara protocol error
12:19:09: ERROR: function: main:303 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
I know it is not the right place but if you know how to fix it
Click to expand...
Click to collapse
Same problem with Leeco x820
Hi guys, I've got the same problem when I try to unbrick my Motorola moto e4, help me please!
Help to restore bootloader on Nokia 6
What happened? We are no magicians
ZeroPointMax said:
What happened? We are no magicians
Click to expand...
Click to collapse
The phone worked properly, but I wanted to install the European firmware, through the program QFIL I installed the firmware in the phone, and after that the phone does not turn on, or rather all the LEDs light up and the computer determines how Port Diagnostics 900E? I ported the drivers all without result. can not enter mode Downalds mod ...
Evgeny_14 said:
The phone worked properly, but I wanted to install the European firmware, through the program QFIL I installed the firmware in the phone, and after that the phone does not turn on, or rather all the LEDs light up and the computer determines how Port Diagnostics 900E? I ported the drivers all without result. can not enter mode Downalds mod ...
Click to expand...
Click to collapse
Oops, you bricked your device. You cannot flash another region if that was your intention... You can either go to customer support or try to make a USB flash cable to force the files onto your device (pls use original firmware for your device). I know that this was mentioned in the forum before but I cannot remember where exactly and I don't know if it is actually working. If it fails, your device is pretty much ******...
Just use the OST Tools and official firmware to root ur device.
Tutorial video:
OST Tools and firmware download: https://forum.xda-developers.com/nokia-6/development/nokia-6-official-firmware-mena-region-t3664441
Recovery download: https://forum.xda-developers.com/no...ecovery-project-nokia-6-t3650499/post73625011
Guide: https://forum.xda-developers.com/no...de-how-to-flash-custom-recovery-root-t3702354
Nokia 6 (TA-1003) bootloader restore how?
Dear,
My phone will not start up
How can i restore the bootloader an reflash the firmware?
I hope on a solution!
Greet,
Marno
desesperated
richardpimenov2001 said:
Just use the OST Tools and official firmware to root ur device.
Tutorial video:
OST Tools and firmware download: https://forum.xda-developers.com/nokia-6/development/nokia-6-official-firmware-mena-region-t3664441
Recovery download: https://forum.xda-developers.com/no...ecovery-project-nokia-6-t3650499/post73625011
Guide: https://forum.xda-developers.com/no...de-how-to-flash-custom-recovery-root-t3702354
Click to expand...
Click to collapse
Hi there. I'm a new user so i don't have enought privileges to make a tread about my issues. So i will try to be the most clear possible.
I got a Nokia 6 TA-1039 so i tryed to root it and that's why I'm here.
First of all the phone is now on Qualcomm HS-USB Qloader singed on 04/01/2013 and it's 2.1.0.5 version, by Xiaomi Technology Inc., then when i connect to the PC it recognizes it in that port. In the other hand, the device doesn't make any noise or dispolay anything on the screen, but in the pc it appears when i connect it.
I have downloaded following the treads the firmware Nokia_TA-1025_MSM8937_25082017_7.1.1.zip and extracted it. I was trying to use it with QFIL version 2.0.0.5 and using as configuration the next steps:
-Download protocol: 0-Sahara
-Device type: UFS
Validation mode: 0-No validation
[
then when i run it i found the next errors:
Error function: Sahara _rx_data: 194 unable to read packet header Only read 0 bytes
Error function: Sahara_main: 854 sahara protocol error
Error function: Sahara_main: 265 Uploading image using sahara protocol failed
Download fail: Sahara fail: QSaharaServer fail: Process fail
Then i tryed to flash it using Xiaomi MiFlash.exe and the errors are:
Cant found programmer file
Cannot recive Hello packet
cannot read hello packet
adittional to this I have a cable that i think that it's a EDL cable by GPGIndustries like this
http://shop.gpgindustries.com/produc...ml?pb=108&pc=2
I'm very desesperated about this. If someone can call me or help me in any way i really appreciate it.
grandroid7 said:
Dear,
My phone will not start up
How can i restore the bootloader an reflash the firmware?
I hope on a solution!
Greet,
Marno
Click to expand...
Click to collapse
I had exactly the same thing. . You must send the phone to the service.
Maxpowers88 said:
Hi there. I'm a new user so i don't have enought privileges to make a tread about my issues. So i will try to be the most clear possible.
I got a Nokia 6 TA-1039 so i tryed to root it and that's why I'm here.
First of all the phone is now on Qualcomm HS-USB Qloader singed on 04/01/2013 and it's 2.1.0.5 version, by Xiaomi Technology Inc., then when i connect to the PC it recognizes it in that port. In the other hand, the device doesn't make any noise or dispolay anything on the screen, but in the pc it appears when i connect it.
I have downloaded following the treads the firmware Nokia_TA-1025_MSM8937_25082017_7.1.1.zip and extracted it. I was trying to use it with QFIL version 2.0.0.5 and using as configuration the next steps:
-Download protocol: 0-Sahara
-Device type: UFS
Validation mode: 0-No validation
[
then when i run it i found the next errors:
Error function: Sahara _rx_data: 194 unable to read packet header Only read 0 bytes
Error function: Sahara_main: 854 sahara protocol error
Error function: Sahara_main: 265 Uploading image using sahara protocol failed
Download fail: Sahara fail: QSaharaServer fail: Process fail
Then i tryed to flash it using Xiaomi MiFlash.exe and the errors are:
Cant found programmer file
Cannot recive Hello packet
cannot read hello packet
adittional to this I have a cable that i think that it's a EDL cable by GPGIndustries like this
http://shop.gpgindustries.com/produc...ml?pb=108&pc=2
I'm very desesperated about this. If someone can call me or help me in any way i really appreciate it.
Click to expand...
Click to collapse
I dont know if this would help you guys or not but this is portable one,
You dont need to configure any sahara file or anything, just select mbn file then xml and hit download
This tool helped me alot for so many other phone which gave me sahara error
Find the tool in the attachment
Hope this will help you
Hit thanks button if you find this helpful
Happy flashing
jurek09 said:
I had exactly the same thing. . You must send the phone to the service.
Click to expand...
Click to collapse
Dear all,
Background: I’ve bought a brand new Lenovo Tab M10 TB-X605L LTE. It’s for my grandma, so that she can video-call her great-grandchildren during the Corona crises, and I learned that I require to have Android 8 Oreo on it, as Teamviewer Host has to run on it and start automatically (my grandma is almost 90 years and she can operate a toaster, but not a tablet). Unfortunately, I’ve upgraded to Android 9 Pie, which by design doesn’t support Teamviewer host.
The problem is: I need to get back to Android 8 Oreo, but I almost bricked my Lenovo Tab M10 by trying to do so. I’ve already spent a few days and read/tried tons of instructions/suggestions/forum discussions, and I’m completely stuck. I would really enjoy some help or the decisive tip – and especially my grandmother would really enjoy seeing her four great-grandchildren after three weeks of quarantine.
This works:
I managed to get a M10 TB-X605L stock ROM Android 8 Oreo: techswizz com/lenovo-tab-tb-x605l-stock-rom-firmware-flash-file/
I can reboot to fastflash mode (reboot and hold Volume-Down), and I can use ADB and Fastboot.
I can install TWRP recovery mode (by flashing recovery.img) and start/use TWRP (reboot and hold Volume-Up+Down).
I think I’ve unlocked the bootloader, but I’m not sure how to verify it.
I have installed the Qualcomm_USB_Driver_v1.0 and the tablet gets a COM port (can be seen in Device Manager).
This doesn’t work:
General
I cannot boot in normal mode (device stops or constantly reboots when I try).
I managed to install Magisk (in TWRP), but the devices still can’t boot in normal mode afterwards, so I cannot start Magisk.
Lenovo Moto Smart Assistant
I can start it, download the stock image. When I try to flash the device, the progress bar jumps to 33% immediately, and after a few seconds a “FAIL” button appears without any further information.
Fastboot
I can flash boot.img and recovery.img, but system.img is splitted in system_1.img, system_2.img, etc., and when I connect these files with packsparseimg.exe, the resulting system.img seems to be invalid (devices doesn’t start).
QFIL
I can see the devices on the COM Port. I can load rawprogram_unsparse.xml and patch0.xml.
When the device comes online, I try to hit Download immediately, and I either get the following error:
[*]ERROR: function: sahara_rx_data:237 Unable to read packet header. Only read 0 bytes.
[*]ERROR: function: sahara_main:924 Sahara protocol error
[*]ERROR: function: main:303 Uploading Image using Sahara protocol failed
[*]Download Fail:Sahara Fail:QSaharaServer Failrocess fail
[*]or it says the device is not in EDL mode (which is easy to fix by booting in EDL mode from TWRP, but then the sahara error comes up).
QPST
I can connect the phone via QPST Configuration (COM3, Q/QCPP-XXX (Sarah Download), USB)-
When I open the “eMMC Software Download app”, I can open the Sahara XML file rawprogram_unsparse.xml – I hope, that’s the right one.
When I “Load XML def…”, I don’t know which xml file to open:
[*]rawprogram_unsparse.xml and rawprogram0.xml.bak show an error “Document error on element type ‘raw program’ and name/value ‘true’”.
[*]Patch0.xml shows no error, but I think it’s the wrong file for “Load XML def”.
Dowloading with “Patch0.xml” leads to an error “Timeout waiting for device”
QcomDLoader.exe (1.3.2.0)
I can „load“ the stock image directory, and set the settings (eMMC programmer: prog_emmc_firehose_8953_lite.mbn, Raw program: rawprogram_unsparse.xml, patch0: patch0.xml).
Wenn I press ‘Start’ the Step/Status “Sahara/Flashing” appears for 5 seconds, followed by messages “failed.
Any help or suggestion is highly appreciated.
Kind regards,
Walter
Hey,
i have the same device and a similar situation - any news on this?
@OP: How did you proceed? Different device, any alternative to teamviewer?
Solution for flashing Qualcomm based Android devices
Dear all,
please find the solution for for flashing Qualcomm based Android devices (sahara_rx_data error) here: https://android.stackexchange.com/questions/224369/cannot-flash-qualcomm-with-stock-image-lenovo-tab-m10-tb-x605l-lte-android-8-o?noredirect=1#comment291391_224369
Kind regards
PS: I'm not allowed to post links here. Can someone please copy-paste the link and add it here?
--SOLUTION TO FLASHING QUALCOMM BASED ANDROID DEVICES-----
Cannot flash Qualcomm with Stock Image (Lenovo Tab M10 TB-X605L LTE, Android 8 Oreo)
Background I’ve bought a brand new Lenovo Tab M10 TB-X605L LTE. It’s for my grandma, so that she can video-call her great-grandchildren during the Corona crises, and I learned that I require to have
android.stackexchange.com
Hi,
I was using my phone normally, it got hung and i restarted it. since then it is stuck at android one screen. Nokia care says motherboard needs to be changed, but I am trying my luck by flashing in EDL mode(short-eda JTAG pins).
I tried flashing using QFIL by choosing the programmer, raw and patch xml files and clicked on Download.
I am facing below issue:
2020-06-13 01:18:40.768 01:18:40: ERROR: function: sahara_rx_data:237 Unable to read packet header. Only read 0 bytes.
2020-06-13 01:18:40.775 01:18:40: ERROR: function: sahara_main:924 Sahara protocol error
2020-06-13 01:18:40.781 01:18:40: ERROR: function: main:303 Uploading Image using Sahara protocol failed
2020-06-13 01:18:40.793 Download Fail:Sahara Fail:QSaharaServer Failrocess fail
2020-06-13 01:18:40.796 Finish Download
Can anyone help me with this?
someone told me that eMMC may be in Read only state, is there a way to make it in read write state? Or fix/unbrick this eMMC?
or may be recover data from it?
Or may b e help me to load OS in a external memory card and start the phone so that i can access eMMC maybe?
This issue becoming very common and a lot of people are getting affected, can someone please help!?
did u enter edl mode ? try to flash ost cracked emergency mode+ oreo firmware which is nbo format
Sent from my TA-1054 using Tapatalk
juwelrana091 said:
did u enter edl mode ? try to flash ost cracked emergency mode+ oreo firmware which is nbo format
Sent from my TA-1054 using Tapatalk
Click to expand...
Click to collapse
Oh yes, I opened the back panel, short the edl point. Am able to see Qualcomm HS USB Loader 9008 in Ports and Coms in Device Manager.
Tried with OST LA using nb0 file (DRG-229D-0-00WW-B01) in Emergency Download Mode.
Also, QFIL using the firehose programmer, raw and patch file xml.
Both of them show Error mentioned above (ERROR: function: main:303 Uploading Image using Sahara protocol failed)
What should I do next?
when u enter edl mode, did u update the driver hs 9008 to Qloader 9008 from ur pc?
Sent from my TA-1054 using Tapatalk
---------- Post added at 10:16 AM ---------- Previous post was at 10:11 AM ----------
https://drive.google.com/file/d/1n91aYT9Di6_v4F3Wjlv8TjfeLc64AcYA/view?usp=drivesdk
try this ost tool and driver https://drive.google.com/file/d/1xgi-XL0rleK1VWoZuNrny5B1GuDM3GUo/view?usp=drivesdk
Sent from my TA-1054 using Tapatalk
juwelrana091 said:
when u enter edl mode, did u update the driver hs 9008 to Qloader 9008 from ur pc?
Sent from my TA-1054 using Tapatalk
---------- Post added at 10:16 AM ---------- Previous post was at 10:11 AM ----------
Sent from my TA-1054 using Tapatalk
Click to expand...
Click to collapse
Tried this, not working. I had latest update of OST LA, tried with that too. Nothing is working.
what massage show? plz give me TeamViewer id pass tommorow... i want to try
Sent from my TA-1054 using Tapatalk
juwelrana091 said:
what massage show? plz give me TeamViewer id pass tommorow... i want to try
Sent from my TA-1054 using Tapatalk
Click to expand...
Click to collapse
Hello, it says, software version is out of date please use an updated version.
I have tried with the latest version it is not working.
is there a way to boot it through external sd card?
i have few posts with me but not sure how to do it for Nokia 6.1 plus as I am new to this..
https://forum.xda-developers.com/transformer-tf701/dead-mmc-ideas-t2830332/page3
https://forum.xda-developers.com/go...o-repairing-corrupted-data-partition-t2577447
https://forum.xda-developers.com/general/help/boot-android-external-sd-card-t3803666
https://forum.xda-developers.com/showpost.php?p=76747247&postcount=258
plz google for ur device motherboard... and recently nokia 7 plus has the same issue.... than the guy just heat the emmc little bit than go to recovery and factory reset worked.
Sent from my TA-1054 using Tapatalk
mananarang said:
Hi,
I was using my phone normally, it got hung and i restarted it. since then it is stuck at android one screen. Nokia care says motherboard needs to be changed, but I am trying my luck by flashing in EDL mode(short-eda JTAG pins).
I tried flashing using QFIL by choosing the programmer, raw and patch xml files and clicked on Download.
I am facing below issue:
2020-06-13 01:18:40.768 01:18:40: ERROR: function: sahara_rx_data:237 Unable to read packet header. Only read 0 bytes.
2020-06-13 01:18:40.775 01:18:40: ERROR: function: sahara_main:924 Sahara protocol error
2020-06-13 01:18:40.781 01:18:40: ERROR: function: main:303 Uploading Image using Sahara protocol failed
2020-06-13 01:18:40.793 Download Fail:Sahara Fail:QSaharaServer Failrocess fail
2020-06-13 01:18:40.796 Finish Download
Can anyone help me with this?
someone told me that eMMC may be in Read only state, is there a way to make it in read write state? Or fix/unbrick this eMMC?
or may be recover data from it?
Or may b e help me to load OS in a external memory card and start the phone so that i can access eMMC maybe?
This issue becoming very common and a lot of people are getting affected, can someone please help!?
Click to expand...
Click to collapse
Hi @CarbonGTR, can you please help me with this, if you can?
Hi @maxturner77, can you please share how you were able to unlock the bootloader and root the device?
Please help!! i will be thankful to you.
mananarang said:
Hi @CarbonGTR, can you please help me with this, if you can?
Hi @maxturner77, can you please share how you were able to unlock the bootloader and root the device?
Please help!! i will be thankful to you.
Click to expand...
Click to collapse
The someone you mentioned is correct. The eMMc is in read-only state and you can do nothing other than replace the whole MoBo.
mananarang said:
Hi,
I was using my phone normally, it got hung and i restarted it. since then it is stuck at android one screen. Nokia care says motherboard needs to be changed, but I am trying my luck by flashing in EDL mode(short-eda JTAG pins).
I tried flashing using QFIL by choosing the programmer, raw and patch xml files and clicked on Download.
I am facing below issue:
2020-06-13 01:18:40.768 01:18:40: ERROR: function: sahara_rx_data:237 Unable to read packet header. Only read 0 bytes.
2020-06-13 01:18:40.775 01:18:40: ERROR: function: sahara_main:924 Sahara protocol error
2020-06-13 01:18:40.781 01:18:40: ERROR: function: main:303 Uploading Image using Sahara protocol failed
2020-06-13 01:18:40.793 Download Fail:Sahara Fail:QSaharaServer Failrocess fail
2020-06-13 01:18:40.796 Finish Download
Can anyone help me with this?
someone told me that eMMC may be in Read only state, is there a way to make it in read write state? Or fix/unbrick this eMMC?
or may be recover data from it?
Or may b e help me to load OS in a external memory card and start the phone so that i can access eMMC maybe?
This issue becoming very common and a lot of people are getting affected, can someone please help!?
Click to expand...
Click to collapse
JTAG/EMMC service can fix ur issue.check inbox.
Nokia 6.1 plus got stuck on android one........I have visited nokia care they told me that motherboard is gone........so is there any other solution for that ......plz Anyone knows?
Help me!
Help me!
Please help me!
I currently have a nokia 6.1 plus phone with a program error when loading the lineageOS 20 firmware, now the device has entered edl by itself, i can't get out, i don't know what to do to save it, hope you guys can help me .
Halo T 4004 said:
Help me!
Help me!
Please help me!
I currently have a nokia 6.1 plus phone with a program error when loading the lineageOS 20 firmware, now the device has entered edl by itself, i can't get out, i don't know what to do to save it, hope you guys can help me .
Click to expand...
Click to collapse
Hey, mine got stuck in edl mode too... Have you found any solutions to this?
lxgit said:
Hey, mine got stuck in edl mode too... Have you found any solutions to this?
Click to expand...
Click to collapse
I found.
here you are.
https://forum.xda-developers.com/t/nokia-6-1-plus-in-edl-no-to-exit-edl-and-failed-to-boot.4548065/