**************Flashing Hard Bricked MI 5s/ MI 5S Plus***********
New Fresh and Working Flash mi 5s 5s Plus, using Deep flash mod, No Fastboot, No Edl, No Test point, very easy and simple, Hit :good: if this helpful for you,
Instructions-
[*]First of all Prepare Deep Flash Cable using Below Guide
[*]Attached Both Coper Wire and then connect this cable with your pc
[*]Now connect your Device to usb [Make Sure Your phone is switched Off]
[*]On Pc go To Device manager and Look on port, {No Available] Don't Worry]
[*] Pull the attached Wire and look Device Manager a New port Is Available HS-USB Diagnostic 9008[ com5, com17 etc]
[*]Ok your Device is ready For Flashing
[*]Run mi Flash click on Browse and Load Fastboot Rom Folder
[*]Click Refresh and Then Flash Done, wait a few Seconds While flashing IS complete ,
[*]Done,
Just like that I freed my Mi5s 64GB version with shop ROM from uuonline and could unlock the bootloader to flash xiaomi.eu ROM....
XN Logos said:
watch Video-
unable to embed video/ playback id error, watch on Youtube
Click to expand...
Click to collapse
I do this on my mi 5s plus but when it starts up its stuck on the MI logo....with no way to shut the phone off. I can get to fastboot or recovery mode but those dont really do anything for me as i have a locked bootloader. Im trying to flash the latest global stable rom from the miui forums. Would you be able to help me?
umirza85 said:
I do this on my mi 5s plus but when it starts up its stuck on the MI logo....with no way to shut the phone off. I can get to fastboot or recovery mode but those dont really do anything for me as i have a locked bootloader. Im trying to flash the latest global stable rom from the miui forums. Would you be able to help me?
Click to expand...
Click to collapse
hey don't worry try same process again just replace unlockable appboot.mbn ang flash again if it say error after Bootloader flash then boot device into fastboot, use command
fastboot oem unlock-go to unlock bootloader and then flash fastboot rom via fastboot,
fastboot flash {partition name] {filename].file type
ex fastboot flash splash splash.img
fastboot flash boot boot.img
fastboot flash system system..img
flash all partitions and you are done, its work for you,
XN Logos said:
hey don't worry try same process again just replace unlockable appboot.mbn ang flash again if it say error after Bootloader flash then boot device into fastboot, use command
fastboot oem unlock-go to unlock bootloader and then flash fastboot rom via fastboot,
fastboot flash {partition name] {filename].file type
ex fastboot flash splash splash.img
fastboot flash boot boot.img
fastboot flash system system..img
flash all partitions and you are done, its work for you,
Click to expand...
Click to collapse
Thanks for the tip! i really hope this works
But a couple questions. Where do i replace unlockable appboot.mbn, and where do i get this from?
Also miFlash 2016.08.30.0 doesnt have the option to replace individual files... should i use an older version?
umirza85 said:
Thanks for the tip! i really hope this works
But a couple questions. Where do i replace unlockable appboot.mbn, and where do i get this from?
Also miFlash 2016.08.30.0 doesnt have the option to replace individual files... should i use an older version?
Click to expand...
Click to collapse
use fastbot to edl if you can't find this file on web, and then again flash Rom,
XN Logos said:
use fastboot to edl if you can't find this file on web, and then again flash Rom,
Click to expand...
Click to collapse
EDL has been removed from Global 8.0.3.0 Build, be careful if you flash it. You better have unlocked BL if you do.
And i tried everything but can not gain EDL mode.
Second info, maybe it will be useful, don't flash this version now, wait for new one this has other problems also.
I just did this with my Xiaomi Mi 5S in order to flash Chinese ROM to the new Global Stable ROM. Since I did not have Unlocked bootloader I used your method, created myself a cable and it all went just like your manual said. Helped me plenty. So I confirm the guide it is great. I am even thinking of borrowing this post to post it as a Guide how to flash Chinese ROM to Global Stable which is actually an issue since, the Chinese ROM does not support flashing via Update method, so it would require unlock. OR Depp Flash If you wont mind.
error
it shows can not read from port . what to do now?
EDL method no longer works miui8.2.3
After the update miui8.2.3 the EDL method does not work anymore, now I am stuck, please if you have solutions thanks to help me my MI5s is bocked
abdo142 said:
After the update miui8.2.3 the EDL method does not work anymore, now I am stuck, please if you have solutions thanks to help me my MI5s is bocked
Click to expand...
Click to collapse
try deep flash
Tried with DFC but stuck at can't read from port com error. Mine is running Global 8.0.3.0 MAGMIDI.
Seehank said:
I just did this with my Xiaomi Mi 5S in order to flash Chinese ROM to the new Global Stable ROM. Since I did not have Unlocked bootloader I used your method, created myself a cable and it all went just like your manual said. Helped me plenty. So I confirm the guide it is great. I am even thinking of borrowing this post to post it as a Guide how to flash Chinese ROM to Global Stable which is actually an issue since, the Chinese ROM does not support flashing via Update method, so it would require unlock. OR Depp Flash If you wont mind.
Click to expand...
Click to collapse
Hi, have similar problem-ie. locked phone and still locked bootloader-would like to try the fun with deep flash cable. I got 7.5 /not 8.0.3/ by now.
Would it work afterwards? Would I have UNLOCKED bootloader afterwards? How to do this and not bricking the phone?
cheers,
Is this method outdated?
I'm trying to flash the natrium_global_images_V8.0.4.0.MBGMIDI_20161216.0000.00_6.0_global rom however I'm stuck while it says "flashing". I have waited 15 minutes but the progress is 0.
Related
Hi All, I have unlocked the bootloader the unnofical way and i am on global 7.1.7.0(LHOMICL) with twrp and root.
I now have recieved the official sms to unlock from xiaomi.
Already i had to open the phone 3 times to get into edl mode. I really dont wont to open the phone agian.
When i try to unlock the tool answers no need to unlock. I think this is because i flashed the adapted emmc_appsboot.mbn and boot.img thru fastboot.
Do i have to change te rom to another version before i try thru edl or fastboot? What is the best procedure to official unlock now because i read a lot of bricks if they try to revert back to original state.
Can some one give me a detailed guide? Thanx in advance.
You need to flash a fully stock edl ROM on top of your current setup.
This will wipe out your hacked bootloader and throw the original (still locked) one back onto your device.
Then just unlock as usual. I did the procedure myself today already as I got my unlock notification today as well.
Ok thnx for the info. I have changed this global rom 7.1.7.0 in great extend and dont wont to lose this setup.
So can I backup my current setup with twrp with the hacked bootloader.
Flash the complete global 7.1.7.0 in edl mode. Unlock with the unlock tool.
Root the rom and install twrp.
After this can i restore the backup with the hacked bootloader with twrp?
I dont know how the unlock tool of xiaomi works, so i could leave the official bootloader in place when i do the restore with twrp and only replace system and data partition or can i flash all the parts back with twrp to keep the unlock?
Wich procedure will keep the official unlock in place or will this unlock stick always?
davegrond said:
Hi All, I have unlocked the bootloader the unnofical way and i am on global 7.1.7.0(LHOMICL) with twrp and root.
I now have recieved the official sms to unlock from xiaomi.
Already i had to open the phone 3 times to get into edl mode. I really dont wont to open the phone agian.
When i try to unlock the tool answers no need to unlock. I think this is because i flashed the adapted emmc_appsboot.mbn and boot.img thru fastboot.
Do i have to change te rom to another version before i try thru edl or fastboot? What is the best procedure to official unlock now because i read a lot of bricks if they try to revert back to original state.
Can some one give me a detailed guide? Thanx in advance.
Click to expand...
Click to collapse
Plz could you help me and tell me where you got the hacked unlocked bootloader cause I bricked my redmi note 3 pro snap dragon and only only fastboot is available and when I try to flash it I get the message device locked boot locked can not flash and plz hobe me a detaild link and downloads and how to flash also I did not get the unlock code and how to get the locked one back z original plz help best regards
Plz indeed to know how to hack the bootloader cause I bricked my phone and I need to make it life
MrColdbird said:
You need to flash a fully stock edl ROM on top of your current setup.
This will wipe out your hacked bootloader and throw the original (still locked) one back onto your device.
Then just unlock as usual. I did the procedure myself today already as I got my unlock notification today as well.
Click to expand...
Click to collapse
please give a detailed tutorial how to do it. I am now in AOSP with unofficially unlocked bootloader. How to relock it again to unlock officially?
Relock Bootloader
I see many asking how to Relock Bootloader, especially those who had unlocked unofficially.
The steps to be followed are following:
(1) Turn on USB debugging for your phone;
Go to Settings -- About Phone --> Touch 7 times on "MIUI version" to Enable Developer Options.
Now go to Settings - Additional Settings - Developer Options --> USB debugging.
Enable USB Debugging and Connect to PC.
(2) Download Fastboot ROM (file extension .tgz or .tar) from
Code:
http://en.miui.com/a-234.html
(3) Boot into EDL
adb devices (to check it's connected)
adb reboot edl
(4) Use MI Flash Tool to Flash the Fastboot ROM
PS: It is assumed that person knows how to get drivers installed for phone if not already, use ADB command as well as know MI Flash Tool basics.
@BRoy_98 @ioosis @davegrond : hope this helps.
@MrColdbird Thanks for the tip
BRoy_98 said:
please give a detailed tutorial how to do it. I am now in AOSP with unofficially unlocked bootloader. How to relock it again to unlock officially?
Click to expand...
Click to collapse
Thx
Sent from my Redmi Note 3 using XDA-Developers mobile app
Unable to relock
Someone please let me know how to relock the bootloader.
I tried flashing the global rom using flash tool but still it says unlocked when i check it from fastboot mode.
anwar08 said:
Someone please let me know how to relock the bootloader.
I tried flashing the global rom using flash tool but still it says unlocked when i check it from fastboot mode.
Click to expand...
Click to collapse
On MiFlash, select folder of Fastboot ROM, then click on Advanced, and in fastboot script select flash_all_lock.bat. After it, close MiFlash then open it again and check in advanced if flash_all_lock.bat comes selected. If yes, close advanced box and flash ROM. Don't forget to close and open MiFlash after choose flash_all_lock.bat script, it's important step. And you can do it in Fastboot mode, don't need to go to EDL mode to flash the ROM.
andersonaragao said:
On MiFlash, select folder of Fastboot ROM, then click on Advanced, and in fastboot script select flash_all_lock.bat. After it, close MiFlash then open it again and check in advanced if flash_all_lock.bat comes selected. If yes, close advanced box and flash ROM. Don't forget to close and open MiFlash after choose flash_all_lock.bat script, it's important step. And you can do it in Fastboot mode, don't need to go to EDL mode to flash the ROM.
View attachment 3854529 View attachment 3854530 View attachment 3854531 View attachment 3854532
Click to expand...
Click to collapse
Am using the 32 bit beta version and there is no Advanced option
anwar08 said:
Am using the 32 bit beta version and there is no Advanced option
Click to expand...
Click to collapse
see if it's in Configuration.
warranty
does rooting redmi note 3 void warranty bcuz it has a locked bootloader and cannot root without unlocking it ????
and can we lock bootloader again for warranty claims ????
plzz help ???
ty.
Why can't we directly update the device..
Like after flashing miui ROM (7.1)then installing (8.1)....will the bootloader get locked....
?....somebody have any idea place help out
Q. Can the device be rooted without voiding warranty?
A. Yes, by unlocking the BL unofficially.
Q. Once rooted and on MiUI, can I update using Updater?
A. No! You'll lock your BL and end up in a bootloop. Instead, use the updater to download the zip file, reboot into recovery (TWRP or ZCX) flash the zip first and then the universal boot.img patched/lazy flasher and reboot to system.
I followed the method mentioned in the replies to relock the bootloader, i.e, flashed the fastboot rom in edl mode
But for some strange reason, when I entered the fastboot mode and checked whether the bootloader is locked or not by "fastboot oem device-info", it said "Device Unlocked: True"
The main problem came when I booted into the ROM; It broke all kinds of wireless connections. The wifi malfunctioned, the phone wouldn't read the SIM cards etc.
Is there a solution? Please help
Thanks
Hi, I have been using official CM13 for about a week now so I have the following things installed in my phone.
>CyanogenMod 13 (official)
>Cyanogen Firmware
>TWRP 3.0.2-2 F2FS (3.0.M-4)
I want to go completely stock again (temporarily until CyanogenMod has VoLTE support) but I have no idea where to start.
I would like to flash
>Stock Xiaomi Recovery
>Latest stable MIUI global.
And remove Cyanogen firmware and install stock Xiaomi MIUI firmware.
I would like to know how and where do I start.
Thank you very much!
I think MiFlash would be the best option, I think it does exactly what you're asking for (it flashes every partition including boot, radios, etc). You can can choose to erase everything, even internal storage, and make your phone as it originally came. I'm not sure it would relock the bootloader, I don't think it will.. Either way, if you unlocked officially you can always unlock again.
Only thing I'm not sure about is if you can install through fastboot or EDL only
I need to know this too
MiFlash using EDL should do the trick
do you have previous mi backup in twrp??
If you are officially unlocked bootloader, no need to enter edl mode. Miflash work from fastboot mode too.
anuneanu said:
If you are officially unlocked bootloader, no need to enter edl mode. Miflash work from fastboot mode too.
Click to expand...
Click to collapse
What if its unlocked unofficially?
naturist said:
What if its unlocked unofficially?
Click to expand...
Click to collapse
Well, i don't know since I'm unlocked it officially.
But it should work, just don't flash the emmc_ appsboot.mbn file. Need to edit the batch file.
Or just use the save twrp.
hello,
first of all i recommend the advanced users to try this method first to see if they succeeds or not if they then, cheers for the new unofficial bootloader unlocking method. here i will provide steps to do:-
Things you need:
- fastboot rom MiUi 8 8.2 will work
-the modified bootloader file
-helpful quick answers
ok so here we begin
PREREQUISITE
-adb and fastboot setup already on your pc
-usb debugging and oem unlocking must be enabled(from developer options)
-mi flash tool ~>Get older version from here (use 20160401)
-driver signature off
step 1
Enable USB debugging and connect device to pc,
now open fastboot and adb folder and there open cmd and type
Code:
adb devices
step 2
you can recognize the device connected to pc
now reboot device to edl mode
Code:
boot to edl by button combination or fastboot command
you can see your phone is in edl(emergancy download mode)
step 3
extract the fastboot file, and goto extracted_folder/images
there you can find a file named emmc_appsboot.mbn
replace with the downloaded emmc file(from begining of post)
step 4
open mi flash tool and connect phone via usb and click on refresh you can seee a COM port with a number on display,
now browse and load the fastboot rom.
step 5
(in this step i'll be specific as same as redmi note 3 bootloader unlocking method is)
click on advanced and there
and choose these
Browse to flash_all.bat in Fastboot rom folder at First option ,
Third option to prog_emmc_firehose_8976_ddr.mbn ,
then last two options browse to rawprogram0.xml and patch0.xml
step 6
after selecting files in advanced ,go back and click on refresh
step 7
now flash the fastboot file as soon flashing completes remove cable and keep holding fastoot combination keys
now you are booted into fastboot
step 8
the fun part(i guess)
goto adb and fastboot folder and open cmd there'
and type
Code:
fastboot devices
to check if device detected or not
now type
Code:
fastboot oem unlock-go
now it should show
Code:
...
OKAY FINISHED
like this
step 9
now if you succeeded step 8 completely
i'd suggest you to check if bootloader is unlocked or not
type
Code:
fastboot oem device-info
if that shows as
Code:
<bootloader> Device Unlocked:true
then Congratulations.. you successfully unlocked bootloader without permission from xiaomi
now for the people who are trying do please inform if this method worked or not
(will be helpful to me for re edit post with ease steps)
credits to my whatsapp friend who given me required files lol :highfive:
AGAIN please do reply, if this method works or not if worked then cheers :victory:
This is the second time I see this Note 3 unlocking stuff posted here...
Since when adb reboot edl works for MI Max? I'll tell you... since never...
Have you tried this procedure yourself? I bet you haven't...
So don't post something so risky without confirming it working personally, please...
I will strongly advice everyone even considering this!!!
nijel8 said:
This is the second time I see this Note 3 unlocking stuff posted here...
Since when adb reboot edl works for MI Max? I'll tell you... since never...
Have you tried this procedure yourself? I bet you haven't...
So don't post something so risky without confirming it working personally, please...
I will strongly advice everyone even considering this!!!
Click to expand...
Click to collapse
Actually.. i curruntly dont have my mi max now.. i saw on a post they told about edl mode.. and i asked other members from xda whatsapp group many of them told me max has edl mode.. and they said they tried it...
Swapnil Soni said:
Actually.. i curruntly dont have my mi max now.. i saw on a post they told about edl mode.. and i asked other members from xda whatsapp group many of them told me max has edl mode.. and they said they tried it...
Click to expand...
Click to collapse
Mi Max has Edl Mode but it cannot be booted by adb reboot edl, edl in mi max can only be booted by combination of buttons.
paarkhi said:
Mi Max has Edl Mode but it cannot be booted by adb reboot edl, edl in mi max can only be booted by combination of buttons.
Click to expand...
Click to collapse
Oh okey, i edit the post
EDL can be booted from fastboot by typing fastboot oem edl on the Mi Max
TheLolageMann said:
EDL can be booted from fastboot by typing fastboot oem edl on the Mi Max
Click to expand...
Click to collapse
Yes i edited in the post
Btw, i wanted to ask has anyone tested this method yet, ?
The method is much too dangerous to test, the modified bootloader file depends on android version and may brick your phone - read more in RN3 thread.
You should not have even posted such a method without personally testing it - we, as in users, are not guinea pigs.
step 5
(in this step i'll be specific as same as redmi note 3 bootloader unlocking method is)
click on advanced and there
and choose these
Browse to flash_all.bat in Fastboot rom folder at First option ,
Third option to prog_emmc_firehose_8976_ddr.mbn ,
then last two options browse to rawprogram0.xml and patch0.xml
Click to expand...
Click to collapse
Xiaomi MiFlash has no "Advanced" button, you are not even linking to the program you are advising to use.
Please remove this post and either do the procedure yourself first or do not post such pos here as nobody could even complete the procedure.
mat9v said:
The method is much too dangerous to test, the modified bootloader file depends on android version and may brick your phone - read more in RN3 thread.
You should not have even posted such a method without personally testing it - we, as in users, are not guinea pigs.
Xiaomi MiFlash has no "Advanced" button, you are not even linking to the program you are advising to use.
Please remove this post and either do the procedure yourself first or do not post such pos here as nobody could even complete the procedure.
Click to expand...
Click to collapse
Actually Mi flash tool has the option for advanced .. if you had the older version .. till now i havent updated to latest version yet, also if you may read above post i told that i currently dont have my max now, and i aint gonna get it in next 1 or 2 years, my brother took it and now he is at his hostel...
I ll link the old miflash tool, and the dangereous thing is only one soft brick(stuck at logo) and bootloop, I have experienced some that bootloaders doesnt vary device by device...
So probability is to get a stuck on logo or get a bootloop its simple that you just load the original fastboot firmware and flash, that reverts back to normal state, for now,
I'm just trying to help, if people dont like it then I will defineatly leave.
Swapnil Soni said:
Actually Mi flash tool has the option for advanced .. if you had the older version .. till now i havent updated to latest version yet, also if you may read above post i told that i currently dont have my max now, and i aint gonna get it in next 1 or 2 years, my brother took it and now he is at his hostel...
I ll link the old miflash tool, and the dangereous thing is only one soft brick(stuck at logo) and bootloop, I have experienced some that bootloaders doesnt vary device by device...
So probability is to get a stuck on logo or get a bootloop its simple that you just load the original fastboot firmware and flash, that reverts back to normal state, for now,
I'm just trying to help, if people dont like it then I will defineatly leave.
Click to expand...
Click to collapse
Yes! We appreciate you trying to help but your missing the point... You have uploaded a guide from another handset expecting it to work for our devices having not tested it previously, the guide isn't even for out device so have fun being guinea pigs
kyler084 said:
Yes! We appreciate you trying to help but your missing the point... You have uploaded a guide from another handset expecting it to work for our devices having not tested it previously, the guide isn't even for out device so have fun being guinea pigs
Click to expand...
Click to collapse
I didnt took all things from rn3 bl unlocking page, i just took method of flashing. And the bootloader file thats taken from officially unlocked bootloade, and i just told if previous post i dont hav max right now, so i wish if someone tried this and if he succeeds.. then its very good news for all locked bl users..
But i think none is not even trying
Definititely some procedures must be changed and adapted to mi max. Experimented developers has portion of truth but some users can`t get answer to unlock devices and me personally if my bootloader was locked don`t want have a device wich can`t be real owner.
Opennig file emmc... remember that an old trick from kitkat to unlock with sucess my old xperia z. some looks be based on the principle to replace original values in the clusters just for zeros. I uploaded two orginal and unlocker emmc files to consider this but of course I can`t confirm cause my bootloader is unlocked.
Some ideas aloud.
There are differences between locked and the official unlocked bootloader (please, see in the hex-editor the end of both files). It's a right idea for replace the locked bootloader (emmc_aboot) to official unlocked emmc_appsboot. The official unlocked emmc_appsboot we can get by dump of the partition in official unlocked device and this binary file will be have the .img extension (uncompressed binary file).
For checking we should check two binary files in the hex-editor: emmc_appsboot.mbn from ROM for fastboot flash and modified bootloader file from author. But files with .mbn extension should be uncompressed.
Sorry, but I don't know as uncompress the .mbn file.
SubwayChamp said:
Definititely some procedures must be changed and adapted to mi max. Experimented developers has portion of truth but some users can`t get answer to unlock devices and me personally if my bootloader was locked don`t want have a device wich can`t be real owner.
Opennig file emmc... remember that an old trick from kitkat to unlock with sucess my old xperia z. some looks be based on the principle to replace original values in the clusters just for zeros. I uploaded two orginal and unlocker emmc files to consider this but of course I can`t confirm cause my bootloader is unlocked.
Click to expand...
Click to collapse
Yeah i checked in hex, i guess its the some kinda lock codes with it so they got removed(i m noob in hex ' )
As far as .. result will be known by practically
Maybe developers can make something similar to safestrap, it was a great project based on bootstrap (now abandoned) that works with a modified recovery that allows install almost any rom on bootloader unlocked (and unlockable cause company never want to unlock it at least till the time I used) on my old galaxy note 3 at&t. This app created a second slot and more directly to install roms.
[U][B]Please, Somone who can revive their device from bootloop[/B][/U]
I thought someone will try it
This is far too risky to try
Sent from my Xiaomi MI MAX using XDA Labs
fail
already try this tutorial and ended my device brick no fastboot mode,cant turn on..solution im using testpoint to get my device unbrick...
Swapnil Soni said:
hello,
first of all i recommend the advanced users to try this method first to see if they succeeds or not if they then, cheers for the new unofficial bootloader unlocking method. here i will provide steps to do:-
Things you need:
- fastboot rom MiUi 8 8.2 will work
-the modified bootloader file
-helpful quick answers
ok so here we begin
PREREQUISITE
-adb and fastboot setup already on your pc
-usb debugging and oem unlocking must be enabled(from developer options)
-mi flash tool ~>Get older version from here (use 20160401)
-driver signature off
step 1
Enable USB debugging and connect device to pc,
now open fastboot and adb folder and there open cmd and type
Code:
adb devices
step 2
you can recognize the device connected to pc
now reboot device to edl mode
Code:
boot to edl by button combination or fastboot command
you can see your phone is in edl(emergancy download mode)
step 3
extract the fastboot file, and goto extracted_folder/images
there you can find a file named emmc_appsboot.mbn
replace with the downloaded emmc file(from begining of post)
step 4
open mi flash tool and connect phone via usb and click on refresh you can seee a COM port with a number on display,
now browse and load the fastboot rom.
step 5
(in this step i'll be specific as same as redmi note 3 bootloader unlocking method is)
click on advanced and there
and choose these
Browse to flash_all.bat in Fastboot rom folder at First option ,
Third option to prog_emmc_firehose_8976_ddr.mbn ,
then last two options browse to rawprogram0.xml and patch0.xml
step 6
after selecting files in advanced ,go back and click on refresh
step 7
now flash the fastboot file as soon flashing completes remove cable and keep holding fastoot combination keys
now you are booted into fastboot
step 8
the fun part(i guess)
goto adb and fastboot folder and open cmd there'
and type
Code:
fastboot devices
to check if device detected or not
now type
Code:
fastboot oem unlock-go
now it should show
Code:
...
OKAY FINISHED
like this
step 9
now if you succeeded step 8 completely
i'd suggest you to check if bootloader is unlocked or not
type
Code:
fastboot oem device-info
if that shows as
Code:
<bootloader> Device Unlocked:true
then Congratulations.. you successfully unlocked bootloader without permission from xiaomi
now for the people who are trying do please inform if this method worked or not
(will be helpful to me for re edit post with ease steps)
credits to my whatsapp friend who given me required files lol :highfive:
AGAIN please do reply, if this method works or not if worked then cheers :victory:
Click to expand...
Click to collapse
please post steps with pictures or link a youtube video, I'll sub you, and I'm sure others will too.
Hello,
I was always a Samsung fanboy, but than I decided to buy the P9 lite (VNS-L21 single sim)
I wanted to flash the android 7 update for my phone, but I was such a noob in Huawei, that I didn't understand a word. But i tried to do what the instructions said. Now my phone is bricked. I can go to recovery, erecovery (which can't download anyithing) and download mode. I heard of this fastboot stuff as well, but I don't know how to do this. I tried to flash as many roms as I could with dload and it didn't work, after 5%, it said it failed... Now I don't know what to do. I think somebody (expert) should make a clear tutorial for noobs. Oh and I almost forgot that i don't have root, custom recovery, and things like that. I just bought the phone, I didn't want to make big changes, just new android. Is it possible that after this Huawei would fix my phone, if I couldn't? Or warranty is void? And sadly I don't know more of my phone because I'm not ina rom, and the phone and papers don't say more.
If you could help me, I would appreciate it:
Raul
Turn off your phone, connect to the pc while holding the volume down button, you will end up in fastboot mode.
I assume you have ADB and drivers installed (if not, install ADB and device drivers).
Optional: unlock your bootloader if it's locked.
Download the latest offical rom zip for your phone version (the marshmallow one), extract the update.app.
Use Huawei extractor to ectract the following files (google is your friend in this one, but its not difficult):
boot.img
recovery.img
cust.img
system.img
After you've done this, connect your phone to the PC in fastboot mode .
Open a command promt from the folder where the extracted files are (shift+right click, Open Command window here), enter the following commands
fastboot devices (you will see the list of attached devices with a lot of random number + fastboot)
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash cust cust.img
fastboot flash system system.img
fastboot reboot
After all this, you should be good to go, just be sure you are using the correct rom for you version.
Or you can just serach on the forum and find this.
https://forum.xda-developers.com/huawei-p9lite/help/unbricking-vns-l21-vns-l31-tutorial-t3583400
(Sorry for my english.)
Fastboot says that it has failed command not alllowed, after I want to installl the files. And I couldn't unlock bootloader without phones information...
rr999999 said:
I would happily unlock my bootloader, but I don't know anyithing about my phone (except model...) without the os...
Click to expand...
Click to collapse
Post here IMEI and SN from the box of phone and i can try get your bootloader unlock code...
If I would unlock it, would fastboot work? Because fastboot pc app recognizes my phone, but my phone says in fastboot mode, that I should connect itself to pc and open hisuite. WTF?
rr999999 said:
If I would unlock it, would fastboot work? Because fastboot pc app recognizes my phone, but my phone says in fastboot mode, that I should connect itself to pc and open hisuite. WTF?
Click to expand...
Click to collapse
Until you have bootloader unlock you can not run any fastboot flash command...
rr999999 said:
If I would unlock it, would fastboot work? Because fastboot pc app recognizes my phone, but my phone says in fastboot mode, that I should connect itself to pc and open hisuite. WTF?
Click to expand...
Click to collapse
Heyho,
normally yes, after bootloader unlock u are able to flash via fastboot. But...
I tried to flash as many roms as I could with dload and it didn't work, after 5%, it said it failed...
Click to expand...
Click to collapse
What is the error? - Have u disconnected the device from the PC during the update?
If not, try to update again and just disconnect the device from any USB connection...
Regards,
Sebastian
k1ll3r8e said:
Heyho,
normally yes, after bootloader unlock u are able to flash via fastboot. But...
What is the error? - Have u disconnected the device from the PC during the update?
If not, try to update again and just disconnect the device from any USB connection...
Regards,
Sebastian
Click to expand...
Click to collapse
Hello. I disconnected it from everything (for example USB)When I tried to install it said something like incompatibility version, but it couldn't be because I tried many roms for my phone. And I tried some dual sim roms as well because, I thought that it might work... But then I will do that unlock if it will do good. Thanks for the help Without bootloader I can't flash from dload as well?
rr999999 said:
Hello. I disconnected it from everything (for example USB)When I tried to install it said something like incompatibility version, but it couldn't be because I tried many roms for my phone. And I tried some dual sim roms as well because, I thought that it might work... But then I will do that unlock if it will do good. Thanks for the help Without bootloader I can't flash from dload as well?
Click to expand...
Click to collapse
Heyho,
the dload method works always without unlock bootloader. But, u can't flash for example an B161 over an B3xx (what nougat is) if the update u installed modified already the oeminfo u are not able to flash any rom below B3xx (nougat) via dload.
-
In that case u might use the official rollback package (never tested it myself) or, u unlock ur bootloader, flash a TWRP recovery matching to ur current FW. Flash from there a oeminfo + custom.bin (lower than B3xx) and flash the FW matching to the new oeminfo via dload and stock recovery.
Regards,
Sebastian
If you have custom recovery, wipe everything. Data, system, boot. extract update app (which is your stock rom) with huawei update extractor. go to custom recovery, flash stock boot IMG and stock recovery IMG. Power off, use three button dload method, reboot, when booting press vol up for three second, now you are in e-recovery. Press shutdown. Press and hold power and vol up for stock recovery. Do factory reset. If need do the factory reset 2/3 times. Now you are with locked bootloader.
Sent from my NEM-L21 using Tapatalk[/QUOTE]
Sent from my NEM-L21 using Tapatalk
A few days ago I bought a Xiaomi Redmi Note 7, I unlocked its bootloader successfully and installed OrangeFox Recovery Project. After that, I installed xiaomi.eu ROM EMUI 12 - Android 10, the latest version of the weekly ROMs for this phone. Since it was a beta ROM, I found some bugs, so I downloaded the stable rom with EMUI 11, but I didn't notice that the zip was corrupted so OrangeFox return an error and I made the mistake of restarting the phone. It was stuck in boot logo and when I enter into fastboot mode, the PC doesn't recognize it. Also, the phone can not enter into recovery mode, it stucks in boot logo.
I have the drivers installed because I tested with another xiaomi en fastboot mode and this one is recognized.
I don't know what to do
Sorry for my english, but I am desperate to fix it. I would really appreciate if someone could help me, please.
it's ok , try format data from orangefox and flash a different zip/rom
EgyBob said:
it's ok , try format data from orangefox and flash a different zip/rom
Click to expand...
Click to collapse
The phone can not enter into recovery mode. :/
Can you enter into fastboot with poder off bottom + volume down ?
If you can then flash a fastboot ROM with mi flash
Check out not relock bootloader
Check "flash all" option https://update.miui.com/updates/v1/fullromdownload.php?d=lavender_global&b=F&r=global&n=
its easy
just unlock bootloader again with miflash unlock then flash any rom you like
uriel cruzitho said:
Can you enter into fastboot with poder off bottom + volume down ?
If you can then flash a fastboot ROM with mi flash
Check out not relock bootloader
Check "flash all" option https://update.miui.com/updates/v1/fullromdownload.php?d=lavender_global&b=F&r=global&n=
Click to expand...
Click to collapse
The problem is that since that happened my cell phone is no longer recognized by the computer.
Phone is not recognized by the PC
My phone is connected now and it is not recognized in fastboot mode.
Dont worry, just put in the commands into fastboot. My device dont get recognized too and i can flash everything.
hi my friend.
sry for my bad english.
i had a redmi 4 prime , and had same problem.
thats get unbricked with a shoke on the phone board.
on the main board of the phone , you have 2 little steel circle and named test points and must connect their to each other .
its easy if you can open the phone. if you cant , you must going to a phone repairer.
like this video
youtu.be/7KyYp_lTR0k
i hope can help you
If your phone can still boot up. Just try to fastboot mode power+vol down. Install latest usb driver for PC. Then try one by one usb port you have on your PC. Because I experienced some usb port doesn't work. And if connected try to reinstall TWRP again.
Uses the previous version of twrp, try connecting the phone to another computer. Use xiaomi usb cable.
228as091215t said:
Dont worry, just put in the commands into fastboot. My device dont get recognized too and i can flash everything.
Click to expand...
Click to collapse
Could you explain to me how you did the Flashing using commands? please
Always you can to made test point and flash with miflash . search in google
:good:
01MaxMarvin said:
A few days ago I bought a Xiaomi Redmi Note 7, I unlocked its bootloader successfully and installed OrangeFox Recovery Project. After that, I installed xiaomi.eu ROM EMUI 12 - Android 10, the latest version of the weekly ROMs for this phone. Since it was a beta ROM, I found some bugs, so I downloaded the stable rom with EMUI 11, but I didn't notice that the zip was corrupted so OrangeFox return an error and I made the mistake of restarting the phone. It was stuck in boot logo and when I enter into fastboot mode, the PC doesn't recognize it. Also, the phone can not enter into recovery mode, it stucks in boot logo.
I have the drivers installed because I tested with another xiaomi en fastboot mode and this one is recognized.
I don't know what to do
Sorry for my english, but I am desperate to fix it. I would really appreciate if someone could help me, please.
Click to expand...
Click to collapse
01MaxMarvin said:
A few days ago I bought a Xiaomi Redmi Note 7, I unlocked its bootloader successfully and installed OrangeFox Recovery Project. After that, I installed xiaomi.eu ROM EMUI 12 - Android 10, the latest version of the weekly ROMs for this phone. Since it was a beta ROM, I found some bugs, so I downloaded the stable rom with EMUI 11, but I didn't notice that the zip was corrupted so OrangeFox return an error and I made the mistake of restarting the phone. It was stuck in boot logo and when I enter into fastboot mode, the PC doesn't recognize it. Also, the phone can not enter into recovery mode, it stucks in boot logo.
I have the drivers installed because I tested with another xiaomi en fastboot mode and this one is recognized.
I don't know what to do
Sorry for my english, but I am desperate to fix it. I would really appreciate if someone could help me, please.
Click to expand...
Click to collapse
If you can put your phone in fastboot mode it's easy, 1) download stock rom. 2 ) unzip the file 3) open it ,and copy all files 3) open the file with ( xiaomi drivers ADB ) than : paste. From the files of the ROM you'll see
" flash all " connect your phone in fastboot mode double click "flash all " and flashing process will start immediately, don't remove your phone until it stops, done.
01MaxMarvin said:
A few days ago I bought a Xiaomi Redmi Note 7, I unlocked its bootloader successfully and installed OrangeFox Recovery Project. After that, I installed xiaomi.eu ROM EMUI 12 - Android 10, the latest version of the weekly ROMs for this phone. Since it was a beta ROM, I found some bugs, so I downloaded the stable rom with EMUI 11, but I didn't notice that the zip was corrupted so OrangeFox return an error and I made the mistake of restarting the phone. It was stuck in boot logo and when I enter into fastboot mode, the PC doesn't recognize it. Also, the phone can not enter into recovery mode, it stucks in boot logo.
I have the drivers installed because I tested with another xiaomi en fastboot mode and this one is recognized.
I don't know what to do
Sorry for my english, but I am desperate to fix it. I would really appreciate if someone could help me, please.
Click to expand...
Click to collapse
01MaxMarvin said:
The problem is that since that happened my cell phone is no longer recognized by the computer.
Click to expand...
Click to collapse
Dude , Try Chinese Version on MI PC Suit. That will recognise your phone for Sure. My phone was also in same situation.
Here is the link of Chinese MI PC Suit with English Translation
miui.blog/ any-devices/china-mi-pc-suite-english-translation/ (Remove Space before 'any')
Chinese MI PC Suit has much more features then Global Version. Like Wiping Your Device , Directly Installing Stock ROM, Etc
Contact Me at +918824712945 (WhatsApp Only - If Any Help Needed)
(Try it Once)