Related
Today i was trying to install the Android Marshmallow 6.0.1 on my Galaxy S5 Snapdragon via Odin, i downloaded the firmware from Sammobile, i verified that the phone model was exactly the same as named on the firmware, i place the .md5 file in the AP slot and everything was ready to go! (The phone was already plugged and in Bootloader mode, and drivers were up to date) then when finishing the flash Odin FAILS to complete the flash and the phone is left with nothing than the Download mode, i panic and try to access recovery mode but realize that there´s no recovery....I proceed to install the recovery.tar into my phone and it works, i start the phone and Samsung logo comes up, finally it loads and does al the process after you flash a Samsung phone.
Everything works just fine!...except for one thing, THERE´S NO RECOVERY!!!. The phone works perfectly but when i try to enter recovery mode, it sends me to Odin mode as it displays a message saying that failed to boot into recovery.
Please help me i don´t know what to do.
Thanks!
Just flash a custom recovery like twrp or cwm
Already did...same problem, recovery won't boot
adavicco said:
Already did...same problem, recovery won't boot
Click to expand...
Click to collapse
You need to flash a pit file to complete the install correctly.
Hi Guys,
today I wanted to flash the latest Stock ROM for my device via ODIN. I've done this many times before and (thought) I knew what I was doing. It is my third Phone frome the same carrier and none of them were branded/ locked devices before. Unfortunatly I wasn't aware that this particular device was locked.
After downloading the international firmware I tried to install it and ODIN got stuck while writing the system.img. After that my phone did not boot up (of course). After that I downloaded and tried to isntall the firmware of the carrier, but I had the exact same issue. When I turn my device on I get to an error screen which tells me to execute an "emergency recovery" via the Samsung smart switch software. But it too gets stuck on some point and only gets me to an error screen.
FRP hinders me to install a custom recovery and the stock one does not allow any isntallations via ADB or SD card.
My qustion is: Does anyone know how I can install a rom from here?
I know that I had to have made some changes prior to the flashing, but as I said I was not aware and an Idiot for not double checking.
Since it is not bricked yet I suppose there must be an answer but I can't find anything.
Thanks in advance
Edit:
After only installing the stock bootloader, I am autmaticly entering it when I boot my devive. On the bottom of the screen is an error message: "dm-verity verification failed...
E:failed to mount /system (invalid argument)"
Fix
For anyone in the same situation: I fixed it.
In the end all you have to do is flash the firmware with the fitting PIT file. If you firmware consists of multiple files and there is a "HOME"-file, flash it with this one first on the AP slot in ODIN. After that the same again just use the AP file this time.
My phone is up and running again now.
fabivons said:
hi guys,
today i wanted to flash the latest stock rom for my device via odin. I've done this many times before and (thought) i knew what i was doing. It is my third phone frome the same carrier and none of them were branded/ locked devices before. Unfortunatly i wasn't aware that this particular device was locked.
After downloading the international firmware i tried to install it and odin got stuck while writing the system.img. After that my phone did not boot up (of course). After that i downloaded and tried to isntall the firmware of the carrier, but i had the exact same issue. When i turn my device on i get to an error screen which tells me to execute an "emergency recovery" via the samsung smart switch software. But it too gets stuck on some point and only gets me to an error screen.
Frp hinders me to install a custom recovery and the stock one does not allow any isntallations via adb or sd card.
My qustion is: Does anyone know how i can install a rom from here?
I know that i had to have made some changes prior to the flashing, but as i said i was not aware and an idiot for not double checking.
Since it is not bricked yet i suppose there must be an answer but i can't find anything.
Thanks in advance
edit:
After only installing the stock bootloader, i am autmaticly entering it when i boot my devive. On the bottom of the screen is an error message: "dm-verity verification failed...
E:failed to mount /system (invalid argument)"
Click to expand...
Click to collapse
have u solved your problem ? This problem i am facing on the s7edge nougat ? Plz help ?
Hey,
look at the second post I made in this thread. There is described how I got my S7 up and running again. I'm not sure if it is a valid solution since it felt like trial and error to me, but I'm writing this text from my S7 so it might be worth a try!
Good luck!
Fabivons said:
Hey,
look at the second post I made in this thread. There is described how I got my S7 up and running again. I'm not sure if it is a valid solution since it felt like trial and error to me, but I'm writing this text from my S7 so it might me worth a try!
Good luck!
Click to expand...
Click to collapse
y i have done that and the device boots up but some applications force close and when i insert the memory card , the phone gets restarted everytime
Fabivons said:
For anyone in the same situation: I fixed it.
In the end all you have to do is flash the firmware with the fitting PIT file. If you firmware consists of multiple files and there is a "HOME"-file, flash it with this one first on the AP slot in ODIN. After that the same again just use the AP file this time.
My phone is up and running again now.
Click to expand...
Click to collapse
Tell us in detail now.
SjDU said:
Tell us in detail now.
Click to expand...
Click to collapse
"please"
I described everything I did in the posts before.
As soon as you can enter the system again all you need to do is deactivate the locks I was talking about in my first post and perform a full wipe.
After that you can install any ROM you want via ODIN just like you are used to.
If that doesn't work for you, I don't have any answers either.
But again:
Prep work:
1. Download most recent ODIN
2. Download the correct firmware for your carrier (from www.sammobile.com)
3. Download the correct PIT file for your device
4. Put your device in download mode
Process:
1. Extract your firmware if it is a zip
2. Start up ODIN
3. Connect your device and check if it's detected by ODIN
3. Put the PIT file in ODIN
4. Put the "HOME" file of your firmware in the PDA slot of ODIN
5. Press start
6. When finished unplug your device and restart phone and ODIN
7. Reconnect your phone and check if it's detected by ODIN
8. Put all the other files of your firmware + the PIT in the correct slot in ODIN
9. Press start
After that my device booted up but still was, as you described too, a little buggy. So I deactivated FRP, activated USB debugging in the dev options, installed TWRP, performed a full wipe and installed another firmware of my choosing via ODIN (without a PIT file this time).
I am running 7.0 on my device now and it works flawlessly.
Fabivons said:
"please"
I described everything I did in the posts before.
As soon as you can enter the system again all you need to do is deactivate the locks I was talking about in my first post and perform a full wipe.
After that you can install any ROM you want via ODIN just like you are used to.
If that doesn't work for you, I don't have any answers either.
But again:
Prep work:
1. Download most recent ODIN
2. Download the correct firmware for your carrier (from www.sammobile.com)
3. Download the correct PIT file for your device
4. Put your device in download mode
Process:
1. Extract your firmware if it is a zip
2. Start up ODIN
3. Connect your device and check if it's detected by ODIN
3. Put the PIT file in ODIN
4. Put the "HOME" file of your firmware in the PDA slot of ODIN
5. Press start
6. When finished unplug your device and restart phone and ODIN
7. Reconnect your phone and check if it's detected by ODIN
8. Put all the other files of your firmware + the PIT in the correct slot in ODIN
9. Press start
After that my device booted up but still was, as you described too, a little buggy. So I deactivated FRP, activated USB debugging in the dev options, installed TWRP, performed a full wipe and installed another firmware of my choosing via ODIN (without a PIT file this time).
I am running 7.0 on my device now and it works flawlessly.
Click to expand...
Click to collapse
the time when u were fixing your device , you were on marshmallow or nougat ? beacuse i am on nougat and whenever i flash twrp , it stucks there and not booting into it even i have ticked the oem unlock and usb debugging in developer mode ?
suhaibahmad said:
the time when u were fixing your device , you were on marshmallow or nougat ? beacuse i am on nougat and whenever i flash twrp , it stucks there and not booting into it even i have ticked the oem unlock and usb debugging in developer mode ?
Click to expand...
Click to collapse
Does the TWRP flash complete? Can you boot up the OS after you flashed TWRP? (And did you download the correct version of TWRP for your device?)
As a last resort, you could try and flash marshmallow on your device and see if it works there.
Fabivons said:
Does the TWRP flash complete? Can you boot up the OS after you flashed TWRP? (And did you download the correct version of TWRP for your device?)
As a last resort, you could try and flash marshmallow on your device and see if it works there.
Click to expand...
Click to collapse
if i flash marshmallow it doesnt even boot up and in the odin mode showing binary and everything as custom , if i flash nougat and then flash twrp and try to manually boot into twrp it stucks on the s7edge screen which comes before recovery , and if i boot the mobile normally without the button combination then it stucks on the second logo SAMSUNG . if i flash again the stock recovery then boots normally
suhaibahmad said:
if i flash marshmallow it doesnt even boot up and in the odin mode showing binary and everything as custom , if i flash nougat and then flash twrp and try to manually boot into twrp it stucks on the s7edge screen which comes before recovery , and if i boot the mobile normally without the button combination then it stucks on the second logo SAMSUNG . if i flash again the stock recovery then boots normally
Click to expand...
Click to collapse
Have you tried to perform a regular factory reset via the OS on nougat? Sometimes that does the job, too.
But as I said. I can only give you my best guess here - my phone worked after my procedure, so I didn't investigate further.
And don't forget: Google is your friend.
Fabivons said:
Have you tried to perform a regular factory reset via the OS on nougat? Sometimes that does the job, too.
But as I said. I can only give you my best guess here - my phone worked after my procedure, so I didn't investigate further.
And don't forget: Google is your friend.
Click to expand...
Click to collapse
thats your kindness , yes i have performed the factory reset several times from recovery , but when i trying to reset it from settings , it goes after restart to recovery with dm-verity error , then i wipe and factory reset from there
Fabivons said:
For anyone in the same situation: I fixed it.
In the end all you have to do is flash the firmware with the fitting PIT file. If you firmware consists of multiple files and there is a "HOME"-file, flash it with this one first on the AP slot in ODIN. After that the same again just use the AP file this time.
My phone is up and running again now.
Click to expand...
Click to collapse
Fabivons said:
"please"
I described everything I did in the posts before.
As soon as you can enter the system again all you need to do is deactivate the locks I was talking about in my first post and perform a full wipe.
After that you can install any ROM you want via ODIN just like you are used to.
If that doesn't work for you, I don't have any answers either.
But again:
Prep work:
1. Download most recent ODIN
2. Download the correct firmware for your carrier (from www.sammobile.com)
3. Download the correct PIT file for your device
4. Put your device in download mode
Process:
1. Extract your firmware if it is a zip
2. Start up ODIN
3. Connect your device and check if it's detected by ODIN
3. Put the PIT file in ODIN
4. Put the "HOME" file of your firmware in the PDA slot of ODIN
5. Press start
6. When finished unplug your device and restart phone and ODIN
7. Reconnect your phone and check if it's detected by ODIN
8. Put all the other files of your firmware + the PIT in the correct slot in ODIN
9. Press start
After that my device booted up but still was, as you described too, a little buggy. So I deactivated FRP, activated USB debugging in the dev options, installed TWRP, performed a full wipe and installed another firmware of my choosing via ODIN (without a PIT file this time).
I am running 7.0 on my device now and it works flawlessly.
Click to expand...
Click to collapse
Well I had the same issue but Odin method didn't work for me on Nougat. And also FRP lock was On. every time I flashed the files it give me FRP on error. so I had to use Smartswitch. Even though I used original csc and ap files with latest Odin. BTW I have SM-G935FD model
SjDU said:
Well I had the same issue but Odin method didn't work for me on Nougat. And also FRP lock was On. every time I flashed the files it give me FRP on error. so I had to use Smartswitch. Even though I used original csc and ap files with latest Odin. BTW I have SM-G935FD model
Click to expand...
Click to collapse
Well FRP has to be turned off (the button in the menu is called "OEM unlock, the button has to be set to on which deactivates FRP). You don't mention using a PIT file - did you use one?
hi all,
first sorry for my bad english.
andorid version 6.0.1, rooted.
i have two problems
first, phone is single sim, but in settings shows "manage sim cards" phone is no g935FD, phone is g935F, but phone works ok.
second, when i update with odin, firmware form sammobile, i can't connect on network, my sim card can't work.
i backup all with flashfire, and when i restore all expect EFS and modem firmware, phone still does't work, and with efs work.
my phone is gift from cousin, and that in settings show only one sim and phone is rooted too.
After that I tried, and I told you what happened.
please help me how to update to 7.0, and how to solve problem with sim.
i tried to update with odin, but when i restore efs and modem, phone, can't connect on network.
UP !
Up !!
Anyone ?
Upppppp
Antonije123 said:
hi all,
first sorry for my bad english.
andorid version 6.0.1, rooted.
i have two problems
first, phone is single sim, but in settings shows "manage sim cards" phone is no g935FD, phone is g935F, but phone works ok.
second, when i update with odin, firmware form sammobile, i can't connect on network, my sim card can't work.
i backup all with flashfire, and when i restore all expect EFS and modem firmware, phone still does't work, and with efs work.
my phone is gift from cousin, and that in settings show only one sim and phone is rooted too.
After that I tried, and I told you what happened.
please help me how to update to 7.0, and how to solve problem with sim.
i tried to update with odin, but when i restore efs and modem, phone, can't connect on network.
Click to expand...
Click to collapse
Can you please provide your device exact model number? It is printed below on the back panel of your phone..Then can suggest you exact stock firmware to flash using odin
DroidHackeR said:
Can you please provide your device exact model number? It is printed below on the back panel of your phone..Then can suggest you exact stock firmware to flash using odin
Click to expand...
Click to collapse
Model is g935f.
I tried superstock room, but again problem with network connect
Antonije123 said:
Model is g935f.
I tried superstock room, but again problem with network connect
Click to expand...
Click to collapse
What do you mean by superstock room? You need to flash latest nought 7.0 stock firmware for your device..
1)Go to the link provided below and select country for your device and download latest 7.0 firmware using free member through registration
https://www.sammobile.com/firmwares/database/SM-G935F/
AFTER THAT FOLLOW ODIN FLASHING GUIDE PROVIDED BELOW
1)You can flash stock firmware for you specific device and country using sammobile.com as a free member registration* Remember to download latest stock firmware for your specific model number and country, you can find your model number printed below on back panel of your phone*
2)Go there in firmware section and enter your device model no and country..( Save it to pc and extract it on your pc in particular firmware folder, you will now find tar.md5 file in that folder)..Now download latest versions of odin and Samsung usb drivers for your device( Extract those files as you did with firmware, install latest usb drivers on pc)
3)From your phone's setting>about device>software info>press build version for 7-8 times continuesly to enable developers option
4)You can find developers option below setting>about device..From developers option select oem unlocking and usb debugging enabled
5)Now connect your phone to pc in download mode( Press volume down+home+power button simultaneously, you are now in download mode..press volume up button to continue)
6) Run odin as device administrator on your pc from odin extracted folder, let pc to install device drivers and your device will be highlighted in odin..
7)Add previously extracted tar.md5 file of stock firmware in AP tab of odin, give it some time to be ready..In odin options let auto reset and reboot options checked..*Dont check repatriation option*
8) Now click start button in odin, flashing process have been started..Sit back and relax untill firmware is being flashed..After that your device will be automatically rebooted and you will have latest stock firmware on your device..
*DO IT ON YOUR OWN RISK NOR I NEITHER ANYONE FROM XDA FORUM WILL BE RESPONSIBLE FOR ANY DAMAGE OR BRICK OF YOUR DEVICE*
DroidHackeR said:
What do you mean by superstock room? You need to flash latest nought 7.0 stock firmware for your device..
1)Go to the link provided below and select country for your device and download latest 7.0 firmware using free member through registration
https://www.sammobile.com/firmwares/database/SM-G935F/
AFTER THAT FOLLOW ODIN FLASHING GUIDE PROVIDED BELOW
1)You can flash stock firmware for you specific device and country using sammobile.com as a free member registration* Remember to download latest stock firmware for your specific model number and country, you can find your model number printed below on back panel of your phone*
2)Go there in firmware section and enter your device model no and country..( Save it to pc and extract it on your pc in particular firmware folder, you will now find tar.md5 file in that folder)..Now download latest versions of odin and Samsung usb drivers for your device( Extract those files as you did with firmware, install latest usb drivers on pc)
3)From your phone's setting>about device>software info>press build version for 7-8 times continuesly to enable developers option
4)You can find developers option below setting>about device..From developers option select oem unlocking and usb debugging enabled
5)Now connect your phone to pc in download mode( Press volume down+home+power button simultaneously, you are now in download mode..press volume up button to continue)
6) Run odin as device administrator on your pc from odin extracted folder, let pc to install device drivers and your device will be highlighted in odin..
7)Add previously extracted tar.md5 file of stock firmware in AP tab of odin, give it some time to be ready..In odin options let auto reset and reboot options checked..*Dont check repatriation option*
8) Now click start button in odin, flashing process have been started..Sit back and relax untill firmware is being flashed..After that your device will be automatically rebooted and you will have latest stock firmware on your device..
*DO IT ON YOUR OWN RISK NOR I NEITHER ANYONE FROM XDA FORUM WILL BE RESPONSIBLE FOR ANY DAMAGE OR BRICK OF YOUR DEVICE*
Click to expand...
Click to collapse
If i only flash ap phone can't run.
Superstock room i downloaded form xda.
Yes i know everything you wrote, but when flash stock firmware my phone on search network show one network, and show that's my phone g935fd.
First time when i update phone, i must send at service, and my phone was been rooted on 6.01 and single sim(g935f) .
I tried to install stock 6.01 via odin from sammobile but don't work
Antonije123 said:
If i only flash ap phone can't run.
Superstock room i downloaded form xda.
Yes i know everything you wrote, but when flash stock firmware my phone on search network show one network, and show that's my phone g935fd.
First time when i update phone, i must send at service, and my phone was been rooted on 6.01 and single sim(g935f) .
I tried to install stock 6.01 via odin from sammobile but don't work
Click to expand...
Click to collapse
You should flash 7.0 latest nougat for your device model no and country instead of 6.0.1 through odin..Try to flash 7.0 stock firmware instead of superstock rom or stock 6.0.1..If you are running your phone well and have root access..Download Samsung phone info app..Grant root access and provide me screen-shot of information shown in that application here..So i can suggest you proper stock firmware to be flashed using odin
DroidHackeR said:
You should flash 7.0 latest nougat for your device model no and country instead of 6.0.1 through odin..Try to flash 7.0 stock firmware instead of superstock rom or stock 6.0.1..If you are running your phone well and have root access..Download Samsung phone info app..Grant root access and provide me screen-shot of information shown in that application here..So i can suggest you proper stock firmware to be flashed using odin
Click to expand...
Click to collapse
Ss
Antonije123 said:
Ss
Click to expand...
Click to collapse
Nougat is still not available for your country..So you have flashed latest stock 6.0.1 firmware using odin? Still you are not getting network signal? After flashing stock firmware don't restore your efs, it will be restored automatically after flashing...Now just again flash the stock 6.0.1 available on sammobile and after flashing when you see Samsung logo, simply press volume down+power button now your screen will turn off..immediately Press volume up+power+home button simultaneously untill you see Samsung galaxy logo, now release keys and you will boot into stock recovery..From there choose wipe data/factory reset option..After reset, reboot your phone..And see if singal back again or not?
DroidHackeR said:
Nougat is still not available for your country..So you have flashed latest stock 6.0.1 firmware using odin? Still you are not getting network signal? After flashing stock firmware don't restore your efs, it will be restored automatically after flashing...Now just again flash the stock 6.0.1 available on sammobile and after flashing when you see Samsung logo, simply press volume down+power button now your screen will turn off..immediately Press volume up+power+home button simultaneously untill you see Samsung galaxy logo, now release keys and you will boot into stock recovery..From there choose wipe data/factory reset option..After reset, reboot your phone..And see if singal back again or not?
Click to expand...
Click to collapse
Can you send me link for what country to download? I download for slovenia 6.01 but still don't work, and i must restore efs,preload and modem firmware.
App i used to backup ans restore flashfire. I don't konw what is preload but is very important to signal.
Antonije123 said:
Can you send me link for what country to download? I download for slovenia 6.01 but still don't work, and i must restore efs,preload and modem firmware.
App i used to backup ans restore flashfire. I don't konw what is preload but is very important to signal.
Click to expand...
Click to collapse
Try this one as your csc in TOP and country is serbia-russia..Flash it using odin and report..By the way before flashing enable OEM UNLOCKING and USB DEBUGGING from developers option..
Link- https://www.sammobile.com/firmwares/download/89389/G935FXXU1BPH6_G935FTOP1BPH1_TOP/
JUST FLASH AS I INSTRUCTED ABOVE IN FIRST POST I.E.HOW TO FLASH STOCK FIRMWARE USING ODIN AND DO FACTORY RESET VIA STOCK RECOVERY AFTER FLASHING AS I SAID IN MY PREVIOUS POST
DroidHackeR said:
Try this one as your csc in TOP and country is serbia-russia..Flash it using odin and report..By the way before flashing enable OEM UNLOCKING and USB DEBUGGING from developers option..
Link- https://www.sammobile.com/firmwares/download/89389/G935FXXU1BPH6_G935FTOP1BPH1_TOP/
JUST FLASH AS I INSTRUCTED ABOVE IN FIRST POST I.E.HOW TO FLASH STOCK FIRMWARE USING ODIN AND DO FACTORY RESET VIA STOCK RECOVERY AFTER FLASHING AS I SAID IN MY PREVIOUS POST
Click to expand...
Click to collapse
Ok, flash only ap or bl, ap, cp,csc ?
Antonije123 said:
Ok, flash only ap or bl, ap, cp,csc ?
Click to expand...
Click to collapse
This is single bundled firmware including ap,cp,bl in it and it is have to flash as AP only..
DroidHackeR said:
This is single bundled firmware including ap,cp,bl in it and it is have to flash as AP only..
Click to expand...
Click to collapse
ok, i will try now, and report here after done
up: after flash i have again two sim, and on search network show me only one network witch is not mine.
Antonije123 said:
ok, i will try now, and report here after done
up: after flash i have again two sim, and on search network show me only one network witch is not mine.
Click to expand...
Click to collapse
Ohhhk now one more tutorial for you and it will help you i guess
1) Download samsung smartswitch application for windows from the link provided below
http://samsungsmartswitch.org/
2) Install latest samsung usb drivers for your s7 edge from below
http://samsungusbdriver.com/download/samsung-driver-v1-5-63-0
3)Now install both samsung smart switch and samsung usb drivers on your windows pc
4) Open samsung smart switch as device administrator on your pc
5) Power off your device and press volume down+home+power button simultaneously untill you get into download mode, now press volume up to continue
6)After installing usb drivers for your phone by pc, your device will be recognised in smart switch
7) Select emergency software recovert option from smart switch
8) It will ask you some information like model no and serial no ( You can find model no and serial no printed below on back panel of phone or on the box of phone)
9) After providing such information, smart switch will locate latest and correct software version to be installed for your device
10) Start update and sit back..It will take some time to update software..After that your device will be reboot and if you are facing bootloop i.e. stuck at samsung logo follow factory reset process i have provided earlier( While your phone stuck at samsung logo for long time, press volume down+power button, screen will turn off now immediatly press volume up+power+home button simultaneously untill you see samsung galaxy s7 edge logo..Now release buttons, you will boot into stock recovery..From there choose wipe data/factory reset option..After reset complete, reboot your device)
*IF SMART SWITCH FAILS TO DETECT YOUR DEVICE, UNINSTALL SAMSUNG USB DRIVER AND INSTALL THEM AGAIN AND FOLLOW PROCESS AGAIN*
● You can refer this guide that how to find and restore exact firmware for your device using Smart switch before trying
https://www.sammobile.com/forum/showthread.php?t=29914
DroidHackeR said:
Ohhhk now one more tutorial for you and it will help you i guess
1) Download samsung smartswitch application for windows from the link provided below
http://samsungsmartswitch.org/
2) Install latest samsung usb drivers for your s7 edge from below
http://samsungusbdriver.com/download/samsung-driver-v1-5-63-0
3)Now install both samsung smart switch and samsung usb drivers on your windows pc
4) Open samsung smart switch as device administrator on your pc
5) Power off your device and press volume down+home+power button simultaneously untill you get into download mode, now press volume up to continue
6)After installing usb drivers for your phone by pc, your device will be recognised in smart switch
7) Select emergency software recovert option from smart switch
8) It will ask you some information like model no and serial no ( You can find model no and serial no printed below on back panel of phone or on the box of phone)
9) After providing such information, smart switch will locate latest and correct software version to be installed for your device
10) Start update and sit back..It will take some time to update software..After that your device will be reboot and if you are facing bootloop i.e. stuck at samsung logo follow factory reset process i have provided earlier( While your phone stuck at samsung logo for long time, press volume down+power button, screen will turn off now immediatly press volume up+power+home button simultaneously untill you see samsung galaxy s7 edge logo..Now release buttons, you will boot into stock recovery..From there choose wipe data/factory reset option..After reset complete, reboot your device)
*IF SMART SWITCH FAILS TO DETECT YOUR DEVICE, UNINSTALL SAMSUNG USB DRIVER AND INSTALL THEM AGAIN AND FOLLOW PROCESS AGAIN*
● You can refer this guide that how to find and restore exact firmware for your device using Smart switch before trying
https://www.sammobile.com/forum/showthread.php?t=29914
Click to expand...
Click to collapse
i tried, but that installated (DRE), and don't work
Antonije123 said:
i tried, but that installated (DRE), and don't work
Click to expand...
Click to collapse
You have tried both stock flashing through odin and also smart switch recovery still not getting any signal?? I think i have helped you in all possible ways i could suggest..Now you can either wait for any expertised advice or simply visit samsung service centre and ask them to restore you phone's original firmware...Sorry and Regards
today i want to share my sad story with u guys , i got my phone huawe mla-al10 , i flash custom rom lineage os 13.1 from xda for huawei can-11 then it got bootloop , before this i succesfully install it without bootloop , so i decide to reset , then i go to the recovery , idk how my recovery become the stock one ,then i click format data , suddenly its stuck at 61% then keep reboot , i open fastboot then get frp locked , im start panic , then i do a research how to get rid frp locked , they said relock the bootloader , then i relock booatlader , haa its getting more worse , now icant even go to fastboot or update mood , its only goes to factory reset lowlevel.... then screen becomes black with blue led , i connect to pc , i found hs-usb diagnostic 9006 ( com 3 ) thats mean i can unbrick only with 1 way , with Snapdragoon flashtool , but i cant find nowhere for the firmware that make to unbrick using flashtool for my devices , hmmm im so sad right now , is there any way i can make my own flashtool file for snapdragon flashtool ? i hope i can fix this as soon as possible
If ADB is working,just flash your original (firmware) RECOVERY,BOOT and SYSTEM.img from the update.app zip file...after flashing those 3 img file,just reboot via adb...fastboot reboot
Phone should be like new
virusdunil said:
If ADB is working,just flash your original (firmware) RECOVERY,BOOT and SYSTEM.img from the update.app zip file...after flashing those 3 img file,just reboot via adb...fastboot reboot
Phone should be like new
Click to expand...
Click to collapse
to make adb working i need to enable usb debugging bla4 but my phone is totally dead , no fastboot nothing i can do except go to edl modee
shazlieyazizan1 said:
to make adb working i need to enable usb debugging bla4 but my phone is totally dead , no fastboot nothing i can do except go to edl modee
Click to expand...
Click to collapse
same problem adb is also not working did you find any solution?
I am having a problem i didnt do anything with my phone its huawei nova plus just 1 or 2 day ago open the boxed and try to update it using firmware finder app after downloading the full ota phone automatically restart and stuck on installing update 5% and its still on boot loop am not able to flash any firmware using sd card or update.app just because it always failed on 5 % even though am not able to wipe factory/reset it also failing. Can you guys please help me? to solve the problem?
abuapka said:
same problem adb is also not working did you find any solution?
I am having a problem i didnt do anything with my phone its huawei nova plus just 1 or 2 day ago open the boxed and try to update it using firmware finder app after downloading the full ota phone automatically restart and stuck on installing update 5% and its still on boot loop am not able to flash any firmware using sd card or update.app just because it always failed on 5 % even though am not able to wipe factory/reset it also failing. Can you guys please help me? to solve the problem?
Click to expand...
Click to collapse
try get correct model from huawei updater finder ..
if dload method not work then try to go to fastboot mode by tgis way >> Turn off your mobile and just click and hold on DOWN vol then connect it with usb it should work !
Recently, I turned off developer options in my rooted S7 Edge (SM-G935FD). Idk if that is the cause, but after rebooting I got the error "Custom Binary Blocked by FRP Lock". I couldnt boot into my recovery (TWRP) either. I was running on Oreo btw. I watched some Youtube guides and apparently the solution was to flash stock rom. So... I flashed an Oreo Stock Rom on my phone via Odin. I thought that would solve my problem, but instead it made it worse. It didnt give me the Custom Binary Blocked by FRP lock error but my boot screen is stuck at the boot animation (not a bootloop). I could boot into the stock recovery tho. I tried a factory reset, that didnt make things better. I could also boot into download mode. I thought I made a mistake, so I flashed like 5-8 times with both CSC an Home_CSC. The result was the same, it would get stuck at the boot animation. I tried flashing TWRP via Odin too, but it said "Custom Binary (Recovery) blocked by FRP Lock". I tried sideloading that TWRP file to my device via ADB. It gave me an error too (I think "Cannot flash from external devices" or something like that) I thought flashing with Re-partition and Nand Erase On would solve my problem, so I tried that, but it didnt work. Im running on Binary 3 apparently. Is there anything I can do?
Rapidfayaround said:
Recently, I turned off developer options in my rooted S7 Edge (SM-G935FD). Idk if that is the cause, but after rebooting I got the error "Custom Binary Blocked by FRP Lock". I couldnt boot into my recovery (TWRP) either. I was running on Oreo btw. I watched some Youtube guides and apparently the solution was to flash stock rom. So... I flashed an Oreo Stock Rom on my phone via Odin. I thought that would solve my problem, but instead it made it worse. It didnt give me the Custom Binary Blocked by FRP lock error but my boot screen is stuck at the boot animation (not a bootloop). I could boot into the stock recovery tho. I tried a factory reset, that didnt make things better. I could also boot into download mode. I thought I made a mistake, so I flashed like 5-8 times with both CSC an Home_CSC. The result was the same, it would get stuck at the boot animation. I tried flashing TWRP via Odin too, but it said "Custom Binary (Recovery) blocked by FRP Lock". I tried sideloading that TWRP file to my device via ADB. It gave me an error too (I think "Cannot flash from external devices" or something like that) I thought flashing with Re-partition and Nand Erase On would solve my problem, so I tried that, but it didnt work. Im running on Binary 3 apparently. Is there anything I can do?
Click to expand...
Click to collapse
I still have the "FRP Lock: On" on download mode, so I tried bypassing FRP lock via binary 5 combination firmware and flashing a binary 7 stock firmware. This time, it doesnt get stuck at the boot animation, instead it redirects to a screen with an android face saying "Installing System updates". A few seconds later, it says "No command" with a dead android face. Then it reboots and the same thing happens. Basically a boot loop, but in a different way. I cant seem to boot to stock recovery either. The worst thing is that I cant even turn off the thing. I have to leave it loop for the entire day until its battery dies
Rapidfayaround said:
I still have the "FRP Lock: On" on download mode, so I tried bypassing FRP lock via binary 5 combination firmware and flashing a binary 7 stock firmware. This time, it doesnt get stuck at the boot animation, instead it redirects to a screen with an android face saying "Installing System updates". A few seconds later, it says "No command" with a dead android face. Then it reboots and the same thing happens. Basically a boot loop, but in a different way. I cant seem to boot to stock recovery either. The worst thing is that I cant even turn off the thing. I have to leave it loop for the entire day until its battery dies
Click to expand...
Click to collapse
after flashing the combination firmware, flash the stock firmware and go thru the boot process
Youdoofus said:
after flashing the combination firmware, flash the stock firmware and go thru the boot process
Click to expand...
Click to collapse
That is what I literally did. I flashed a combination firmware, factory rested my entire phone, turned on developer options as well as allow usb debugging, attempted to reset FRP via Z3X Samsung Tool Pro and finally flashed a stock rom. And, the result is this. A bootloop with an android face dying. I did manage to enter a different screen by pressing volume up once along with pressing volume down and power button. It said "could not open recovery_because_no file directory" and had some more errors. The thing is....I made it worse at the first place. I could have flashed a room with binary 6 or lower, cuz at least the combination firmware would have been available to flash, but my stupid brain did not think of that. I flashed a binary 7 stock rom and there is no combination firmware with a binary of 7 or more. Which means, I will most likely get the "SW check fail Device: 7 Binary: 6 " error while flashing.
Rapidfayaround said:
That is what I literally did. I flashed a combination firmware, factory rested my entire phone, turned on developer options as well as allow usb debugging, attempted to reset FRP via Z3X Samsung Tool Pro and finally flashed a stock rom. And, the result is this. A bootloop with an android face dying. I did manage to enter a different screen by pressing volume up once along with pressing volume down and power button. It said "could not open recovery_because_no file directory" and had some more errors. The thing is....I made it worse at the first place. I could have flashed a room with binary 6 or lower, cuz at least the combination firmware would have been available to flash, but my stupid brain did not think of that. I flashed a binary 7 stock rom and there is no combination firmware with a binary of 7 or more. Which means, I will most likely get the "SW check fail Device: 7 Binary: 6 " error while flashing.
Click to expand...
Click to collapse
If the device is still entering download mode, install the recent version of stock for your device. Maybe that will solve your problem.
Rapidfayaround said:
That is what I literally did. I flashed a combination firmware, factory rested my entire phone, turned on developer options as well as allow usb debugging, attempted to reset FRP via Z3X Samsung Tool Pro and finally flashed a stock rom. And, the result is this. A bootloop with an android face dying. I did manage to enter a different screen by pressing volume up once along with pressing volume down and power button. It said "could not open recovery_because_no file directory" and had some more errors. The thing is....I made it worse at the first place. I could have flashed a room with binary 6 or lower, cuz at least the combination firmware would have been available to flash, but my stupid brain did not think of that. I flashed a binary 7 stock rom and there is no combination firmware with a binary of 7 or more. Which means, I will most likely get the "SW check fail Device: 7 Binary: 6 " error while flashing.
Click to expand...
Click to collapse
the "no such file or directory" error is due to either having had removed stock recovery in flashing the firmwares or the factory recovery corrupted due to likely the same reason. Just flash a revision 7 firmware for your phone and it will at least boot
Dark Stranger said:
If the device is still entering download mode, install the recent version of stock for your device. Maybe that will solve your problem.
Click to expand...
Click to collapse
^^^ this ^^^
Dark Stranger said:
If the device is still entering download mode, install the recent version of stock for your device. Maybe that will solve your problem.
Click to expand...
Click to collapse
I have literally flashed the latest stock rom for my device and my country which is G935FXXS7ESK8.
I am a bit confused tho...I am not sure if my device is SM-G935FD or SM-G935F. The download mode says SM-G935F...but this phone used to work with a SM-G935FD rom back in the days. Is this causing the problem most likely? And btw the repair shop said they cant fix it too
Rapidfayaround said:
I have literally flashed the latest stock rom for my device and my country which is G935FXXS7ESK8.
I am a bit confused tho...I am not sure if my device is SM-G935FD or SM-G935F. The download mode says SM-G935F...but this phone used to work with a SM-G935FD rom back in the days. Is this causing the problem most likely? And btw the repair shop said they cant fix it too
Click to expand...
Click to collapse
I am somehow relieved to know that someone else on this planet is on the same (EXACT) boat as me....this is what we get for messing around too much with our phone hum?
1 - After booting up my phone I get the blue background with a dead Android and "No Command" message
2 - I tried accessing recovery by pressing Power+Home+VolumeUp, but all I get is a black screen with a wall of code lines with "fail to open recovery_cause(No such file or directory)" at the beggining of the text.
3 - "No problem! I'll just flash TWRP with ODIN and install a custom ROM and be done with it!".
..NOPE! FRP(factory reset protection) is ON!!! I cannot install TWRP
4- I've tried to find a combination file with binary version 7...but looks like the internet doesn't seem to care about the good ol' number 7...All I can find is binary version 6.
What Im trying to do now is creating my own combination file binary version 7 (if that's even a thing...) from a stock firmware. But I'm not getting any luckier down this path.
Looks like we need a hero...:crying:
PseudoNoob said:
I am somehow relieved to know that someone else on this planet is on the same (EXACT) boat as me....this is what we get for messing around too much with our phone hum?
1 - After booting up my phone I get the blue background with a dead Android and "No Command" message
2 - I tried accessing recovery by pressing Power+Home+VolumeUp, but all I get is a black screen with a wall of code lines with "fail to open recovery_cause(No such file or directory)" at the beggining of the text.
3 - "No problem! I'll just flash TWRP with ODIN and install a custom ROM and be done with it!".
..NOPE! FRP(factory reset protection) is ON!!! I cannot install TWRP
4- I've tried to find a combination file with binary version 7...but looks like the internet doesn't seem to care about the good ol' number 7...All I can find is binary version 6.
What Im trying to do now is creating my own combination file binary version 7 (if that's even a thing...) from a stock firmware. But I'm not getting any luckier down this path.
Looks like we need a hero...:crying:
Click to expand...
Click to collapse
OMGGGGGGGG....Looks like I am not the only one. DAMN. Bro...tell me if you find a solution ok? Hopefully there is a way to solve this problem...there has to be one. And share your combination firmware after you finish it. Thank you very much
Rapidfayaround said:
OMGGGGGGGG....Looks like I am not the only one. DAMN. Bro...tell me if you find a solution ok? Hopefully there is a way to solve this problem...there has to be one. And share your combination firmware after you finish it. Thank you very much
Click to expand...
Click to collapse
No luck over here friend...
Desperate times require desperate measures. Have you ever tried flashing combination files from different S7 Edge versions?
I can find files for the G935A with a revision 7 of the binary...Im thinking flashing it into my G935F and see what happens. I've read the risks associated with installing firmwares from other phone versions, but I'll have a paperweight either way.
I'll keep this thread updated.
Rapidfayaround said:
I have literally flashed the latest stock rom for my device and my country which is G935FXXS7ESK8.
I am a bit confused tho...I am not sure if my device is SM-G935FD or SM-G935F. The download mode says SM-G935F...but this phone used to work with a SM-G935FD rom back in the days. Is this causing the problem most likely? And btw the repair shop said they cant fix it too
Click to expand...
Click to collapse
Doesn't really matter if you have a F or FD. I'd say you flash the latest stock rom for G935F or FD(which ever is latest) for any country regardless. By this you should be able to boot and won't get any odin errors.
UsmaniMustafa said:
Doesn't really matter if you have a F or FD. I'd say you flash the latest stock rom for G935F or FD(which ever is latest) for any country regardless. By this you should be able to boot and won't get any odin errors.
Click to expand...
Click to collapse
Can you provide me the link plz.
Turns out, its a hardware problem with the storage. Replacing the motherboard might be the solution I think. :/
I had solved my phone last day
At first u can flash ur phone to leatest stock rom. Then u have to turn of frp lock. Then u will able to boot up your phone. If u cant fix u can knock me on facebook. (If u r a z3x user). Bcoz u need z3x for bypass frp with ufs cable.
Im also using s7 edge.
hazratboss said:
At first u can flash ur phone to leatest stock rom. Then u have to turn of frp lock. Then u will able to boot up your phone. If u cant fix u can knock me on facebook. (If u r a z3x user). Bcoz u need z3x for bypass frp with ufs cable.
Im also using s7 edge.
Click to expand...
Click to collapse
Oh ok I will contact you
hazratboss said:
At first u can flash ur phone to leatest stock rom. Then u have to turn of frp lock. Then u will able to boot up your phone. If u cant fix u can knock me on facebook. (If u r a z3x user). Bcoz u need z3x for bypass frp with ufs cable.
Im also using s7 edge.
Click to expand...
Click to collapse
Does it matter if I use the cracked version without box. And no, I dont have the ufs cable. Is there anything else I can do?
Hi guys, I have the exact same problem with my S7 edge from T-mobile (g935t). Odin will only accept for flash the latest rom and after flash it reboots but I get BSOD. I tried a pit file also from an old g935T rom which was android 6.0 and I managed to get into recovery for a moment and I did a factory reset/wipe cache but after reboot entered again in a black screen and the blue led was lit. I finally removed the battery to turn the phone off. I can still enter download mode but is there anything else I can do to resurrect the phone?
Samsung s7 edge (g935f)
Hi everyone , please am having issue of NO COMMAND and i cant boot into recovery. My oem is on so i cant install twpr neither. Am on binary u8. Please any solution to recover my phone?
Very very good new guys...yep you guessed it right. I was able to fix this problem.
How you may ask? Follow these steps
Note: Make sure you have enough battery. Lack of battery charge in my case caused alot of problems.
1. Download a U7 Rom for your SM-G935F or SM-G935FD
2. Extract the Rom as well as the AP
3. After you extract the AP, you will be greeted with boot.lz4.img , recovery.lz4.img , system.lz4.img & meta-data
4. Make a backup of recovery.lz4.img and meta-data just in case. Also, make a copy of boot.lz4.img and rename the copied one to recovery.lz4.img. Don't forget to delete the original recovery and meta-data
5. Now, you should be left with boot.lz4.img , (modified) recovery.lz4.img and system.lz4.img.
6. Now, download this https://www.mediafire.com/file/ah20ha869prdkkc/Autotar2.0_By_FixFirmwares.com.rar/file
7. Now, make a .md5 file that contains (modified) recovery.lz4.img and system.lz4.img
8. After you are done making that .md5, flash it along with CSC, CP and BL.
9. You should directly boot into your device, (if you do), charge your phone for a while if the battery is lower than 20%.
10. Then, go to the settings and enable OEM Unlock before doing ANYTHING
11. Then, reboot to download mode and flash TWRP
12. Download the no-verity-encryption.zip
https://zackptg5.com/android.php#disverfe
13. Allow system modifications and format data (NOT WIPE)
14. If that doesn't work, go to TWRP, connect it to your PC and copy the no-verity-encryption.zip file and install it
15. If that still doesn't work then, follow this tutorial
https://www.google.com/amp/s/forum....niversal-dm-verity-forceencrypt-t3817389/amp/
16. Then, you should boot and yea...enjoy ?
If this method doesn't work then, you need to try different combinations.
Try packing these files in AP
1. Boot.lz4.img, (Modified) Recovery.lz4.img & system.lz4.img
2. (Modified) Recovery.lz4.img & system.lz4.img
3. Meta-data, Boot.lz4.img, (Modified) Recovery.lz4.img & system.lz4.img
If that doesn't work, I'm sorry this is how I fixed it. ?*
For anyone wondering how I fixed it well, firstly a HUGE THANKS TO @shah22 & @Tapas27sTapas2. This would have been LITERALLY IMPOSSIBLE WITHOUT THEM. So, basically I tried an AP with renamed recovery.lz4.img and system.lz4.img only along with CP, CSC and BL. Due to my phone having literally 0%, this journey was very difficult.
Feel free to ask any question
Very very good new guys...yep you guessed it right. I was able to fix this problem.
How you may ask? Follow these steps
Note: Make sure you have enough battery. Lack of battery charge in my case caused alot of problems.
1. Download a U7 Rom for your SM-G935F or SM-G935FD
2. Extract the Rom as well as the AP
3. After you extract the AP, you will be greeted with boot.lz4.img , recovery.lz4.img , system.lz4.img & meta-data
4. Make a backup of recovery.lz4.img and meta-data just in case. Also, make a copy of boot.lz4.img and rename the copied one to recovery.lz4.img. Don't forget to delete the original recovery and meta-data
5. Now, you should be left with boot.lz4.img , (modified) recovery.lz4.img and system.lz4.img.
6. Now, download this https://www.mediafire.com/file/ah20ha869prdkkc/Autotar2.0_By_FixFirmwares.com.rar/file
7. Now, make a .md5 file that contains (modified) recovery.lz4.img and system.lz4.img
8. After you are done making that .md5, flash it along with CSC, CP and BL.
9. You should directly boot into your device, (if you do), charge your phone for a while if the battery is lower than 20%.
10. Then, go to the settings and enable OEM Unlock before doing ANYTHING
11. Then, reboot to download mode and flash TWRP
12. Download the no-verity-encryption.zip
https://zackptg5.com/android.php#disverfe
13. Allow system modifications and format data (NOT WIPE)
14. If that doesn't work, go to TWRP, connect it to your PC and copy the no-verity-encryption.zip file and install it
15. If that still doesn't work then, follow this tutorial
https://www.google.com/amp/s/forum....niversal-dm-verity-forceencrypt-t3817389/amp/
16. Then, you should boot and yea...enjoy ?
If this method doesn't work then, you need to try different combinations.
Try packing these files in AP
1. Boot.lz4.img, (Modified) Recovery.lz4.img & system.lz4.img
2. (Modified) Recovery.lz4.img & system.lz4.img
3. Meta-data, Boot.lz4.img, (Modified) Recovery.lz4.img & system.lz4.img
If that doesn't work, I'm sorry this is how I fixed it. ?*
For anyone wondering how I fixed it well, firstly a HUGE THANKS TO @shah22 & @Tapas27s. This would have been LITERALLY IMPOSSIBLE WITHOUT THEM. So, basically I tried an AP with renamed recovery.lz4.img and system.lz4.img only along with CP, CSC and BL. Due to my phone having literally 0%, this journey was very difficult.
Feel free to ask any question