Hello all .
I have a Santhosh CM13 with FP fix . My FP got Detected and you can register but you can't unlock the phone , as it just vibrate when you touch .
I was able to fix it with this method :
1- Delete your finger Print first .
2- Create a new one and when it ask you to touch multiple times , Do it but do not change the position too much and try to make multiple same position finger scan .
3 - try it and if didn't work create a 2nd finger print and try it .
4- If did not work delete both and repeat .
After couple of tries I manged to make it work and it work like a charm with very fast response . When you reboot your phone the FP won't work and you have to repeat the whole process again .
Thanks to @Santhosh M for the ROM and fix .
Related
Recently I installed Lolipop Custom Rom in my Lava Iris X8 Mobile . Now I want to go back to the stock Rom. I Found a thread in this forum that how to install Stock Rom Using SP Flash Tool
loaded the scatter file.
After that I clicked Download Button
Switched off my phone ( Battery is Non Removable).
Connected mobile to PC (Usb debugging Enabled)
But Nothing Happened.I also pressed volume UP , Down Buttons.No Response. I think my phone is not detected.
Please tell me how to flash Stock Rom in Lava Iris X8 (MT6592)
Can I flash Multi Roms on Lava Iris X8 ?
I had the same problem and had to wait for months for a solution.
The solution is very simple . You need to install the drivers of the phone on the computer. You can Google that or if you can't find working one I will post a link for you.
By the way are like this,
1st completely switch off your phone.
2nd Load the scatter file press download in the SF FLASH tool
3rd connect your phone immediately in switched off state by pressing the volume up button.
if the drivers are installed correctly then your computer will recognized the device.
4th SP FLASH tool will start the process and after completing you can disconnect your phone.
NOTE : 1st time switching on will take a lot more time than usual .
Hope it helps.
**********************
By the way Can you tell if the lollipop custom ROM has touch wiz ui or not?
No I don't think that you can flash multi ROMs on lava Iris x8.
Straw Hat Luffy said:
I had the same problem and had to wait for months for a solution.
The solution is very simple . You need to install the drivers of the phone on the computer. You can Google that or if you can't find working one I will post a link for you.
By the way are like this,
1st completely switch off your phone.
2nd Load the scatter file press download in the SF FLASH tool
3rd connect your phone immediately in switched off state by pressing the volume up button.
if the drivers are installed correctly then your computer will recognized the device.
4th SP FLASH tool will start the process and after completing you can disconnect your phone.
NOTE : 1st time switching on will take a lot more time than usual .
Hope it helps.
**********************
By the way Can you tell if the lollipop custom ROM has touch wiz ui or not?
No I don't think that you can flash multi ROMs on lava Iris x8.
Click to expand...
Click to collapse
I tried after installing correct drivers. It is working.
Thanks for the information.
Should I click "Format All + Download "
No "Download Only" is the correct option.
Please tell about the interface of the lollipop custom ROM. Is it touch wiz or not??
sir
i have done all the thing to told but all in vain
driver install
flash tool
with volume plus
nothing happen kindly provide me screen shot if posible ...
thanks
driver for lava iris x8
Kindly provide me driver for lava iris x8
Need driver for lava iris x8
Straw Hat Luffy said:
I had the same problem and had to wait for months for a solution.
The solution is very simple . You need to install the drivers of the phone on the computer. You can Google that or if you can't find working one I will post a link for you.
By the way are like this,
1st completely switch off your phone.
2nd Load the scatter file press download in the SF FLASH tool
3rd connect your phone immediately in switched off state by pressing the volume up button.
if the drivers are installed correctly then your computer will recognized the device.
4th SP FLASH tool will start the process and after completing you can disconnect your phone.
NOTE : 1st time switching on will take a lot more time than usual .
Hope it helps.
**********************
By the way Can you tell if the lollipop custom ROM has touch wiz ui or not?
No I don't think that you can flash multi ROMs on lava Iris x8.
Click to expand...
Click to collapse
Could you please provide me a correct url to download the driver for lava iris x8.
Not working
But still it is not working...After pressing volume up button nothing happened and please provide drivers download link
Not Working, please check and confirm
Straw Hat Luffy said:
I had the same problem and had to wait for months for a solution.
The solution is very simple . You need to install the drivers of the phone on the computer. You can Google that or if you can't find working one I will post a link for you.
By the way are like this,
1st completely switch off your phone.
2nd Load the scatter file press download in the SF FLASH tool
3rd connect your phone immediately in switched off state by pressing the volume up button.
if the drivers are installed correctly then your computer will recognized the device.
4th SP FLASH tool will start the process and after completing you can disconnect your phone.
NOTE : 1st time switching on will take a lot more time than usual .
Hope it helps.
**********************
By the way Can you tell if the lollipop custom ROM has touch wiz ui or not?
No I don't think that you can flash multi ROMs on lava Iris x8.
Click to expand...
Click to collapse
I tried above given simple method but nothing worked. I downloaded the android USB driver and Lava Smartphone USB driver and properly installed both to my PC and switched off my phone and when, I am connecting it via USB cable along with Volume UP button, it is not connecting in SP flash tool and got boot into recovery...
Is there any other option to connect my Lava Iris X8 with SP flash tool? please guide us.
and please share the driver package that you use for lava Iris X8....:good:
Try This, Worked 100%
rtmoorthy said:
Recently I installed Lolipop Custom Rom in my Lava Iris X8 Mobile . Now I want to go back to the stock Rom. I Found a thread in this forum that how to install Stock Rom Using SP Flash Tool
loaded the scatter file.
After that I clicked Download Button
Switched off my phone ( Battery is Non Removable).
Connected mobile to PC (Usb debugging Enabled)
But Nothing Happened.I also pressed volume UP , Down Buttons.No Response. I think my phone is not detected.
Please tell me how to flash Stock Rom in Lava Iris X8 (MT6592)
Can I flash Multi Roms on Lava Iris X8 ?
Click to expand...
Click to collapse
Dear @rtmoorthy
try this this is surely gonna work
http://forum.xda-developers.com/and...-stock-rom-lava-iris-x8-t3314437#post65310961
---------- Post added at 09:19 PM ---------- Previous post was at 09:15 PM ----------
dhayanikumaryadav said:
But still it is not working...After pressing volume up button nothing happened and please provide drivers download link
Click to expand...
Click to collapse
Dear dhayanikumaryadav
check this link this is working and it has driver also....
http://forum.xda-developers.com/and...-stock-rom-lava-iris-x8-t3314437#post65310961
I install lolipop update .Zip (681.58) in lava iris X8 but it is not completed .it is stuck in Android is processing, it takes a minute.... Wat i do now....
I can't switch of the mobile ,i pressed tha power button serval times but mobile Is On and do updating how to i solve this....Plsz help meee
R u still having the issue
i cant detect sim after i installed rom in my device
hi i am unable to flash my lava iris x8 even i used the steps you shown here. after pressing download in flash tool even by pressing volume up key it was not deducted
Can I Know How To Flash Custom Rom 7 Recovery
1.If your phone status showing custom
Remove ur sd card and than try
Falsh via odin
2. If ur phone fingerprint not working
Go and test *#0*#
3. Enble Lte (4g)
Its does not require root
Step 1 update ur mobile with lateset marshmallow update
U automatically get volte feuture
Step 2 go to access point and check setting
4. Efs failed to mount / dm verification failed
Change ur phone motherboard ( frist try all method available on xda )
5. Hang reboot etc
Download wake up from playstore and set it 4
Any other question? ? Thank u
Regarding 5. Hang reboot etc
Did you mean Wake Lock (https://play.google.com/store/apps/details?id=eu.thedarken.wl&hl=en)?
Model : Yureka A5510 [not plus]
my phone was working perfectly .. no issues at all.. after JIO 4g launch. I read some of the articles to enable VoLTE without using JIOVoice application. I though to enable VoLTE.. and tried to install a firmware for my Yureka A5510.
and I hardbricked my phone. Just redlight blink on top left cornor. NO BOOT, NO FASTBOOT, NO RECOVERY
I googled. and found some article to unbrick by flashing eMMC image on SD card to bring it in to fastboot mode. (using six pins on the motherboard and key comnbination)
finally I am succeed to flash the STOCK firmware by FASTBOOT.
But I lost the IMEI, so NO network.. again googled a lot and I made the IMEI fix with the help of QXDM Tool.
now the problem is with the touch screen. it works fine after a restart untill I press the Lock / unlock button.
After Unlock the touch pointer shows on different locatoin and lower 1/4 part doesn't respond.
I enabled developer mode and enable show touch points... that tells me the location of the touch.
I AM PRETTY MUCH SURE IT IS NOT A HARDWARE ISSUE, BECAUSE IF WORKS FINE IN RECOVERY MODE(CWM RECOVERY) AND ONCE AFTER EVERY RESTART.
.. CAN YOU HELP ME .. PLEASE.
PLEASE TAKE SOME TIME AND READ IT.
I have same Yureka model YU5510A and i soft bricked my phone when i was flashing VoLte Rom. It's been 1 whole month and i haven't found any solution. i tried flashing through CM recovery and fastboot and YGDP tool but non of it works. I am so pissed off. Did you find any solution bro?
Hi experts,
I just wanted to know whether i could able to recover my device or not . Please do help me on this .
Because if i cant , i can move to service center for an exchange of mother board.
About device details : SAMSUNG GALAXY NOTE 4 (N910G).
What happened : Device running Android 6.0.1 (Update 3 rom) which is in snapdragon section .
1. Using device as normal and it was running great for 1 year and 1 month .
Phone suddenly hanged and i was like (hell mood) removed the battery . after that boom nothing works .
Symptoms which i am facing :
1. No boot , No charging sign , No bootloader , No recovery - not even single option is working .
Positive sign :
1. Phone detecting in the laptop as Qualcomm when connected .
and some hope on this thread - which i am not able to recover so far :crying: (may be i am missing the right debrick image)
I am still in a confusing state whether i can able to recover my device or not ..
if yes with the above method or any other way .. above method requires you people expert help as it is missing debrick image (3GB complete similar to N910F debrick image ).
Please and kindly advice me on the my issue.
Thanks for understanding
vndkmr97 said:
Hi experts,
I just wanted to know whether i could able to recover my device or not . Please do help me on this .
Because if i cant , i can move to service center for an exchange of mother board.
About device details : SAMSUNG GALAXY NOTE 4 (N910G).
What happened : Device running Android 6.0.1 (Update 3 rom) which is in snapdragon section .
1. Using device as normal and it was running great for 1 year and 1 month .
Phone suddenly hanged and i was like (hell mood) removed the battery . after that boom nothing works .
Symptoms which i am facing :
1. No boot , No charging sign , No bootloader , No recovery - not even single option is working .
Positive sign :
1. Phone detecting in the laptop as Qualcomm when connected .
and some hope on this thread - which i am not able to recover so far :crying: (may be i am missing the right debrick image)
I am still in a confusing state whether i can able to recover my device or not ..
if yes with the above method or any other way .. above method requires you people expert help as it is missing debrick image (3GB complete similar to N910F debrick image ).
Please and kindly advice me on the my issue.
Thanks for understanding
Click to expand...
Click to collapse
Its more than a 36 views and no reply from anyone . can someone please post your views , so that i will be in a conclusion to change motherboard or go for new device or can solve the issue in any way
Hello , ive been facing this problem since 2 days ago working day and night to fix it and i didnt found a way to do it.
All started with a Hard brick that detected the device as Diagnostic 900E i did a test point and solve it so easy, then i installed a rom a android 8.0 rom and here is where the problem begun.
It looks like it was all perfect i started with the initial configuration, but when it went for select the wifi the phone reboots all the time. I tried to skip every config and managed to get on the sistem but then it reboots over and over every 1 or 2 min the phone reboots by himself. I flashed a lot of roms and none of them works , wiped everything from normal recovery and twrp and nothing. Does anyone has any info of this issue? A friend of mine who also bought a mia1 had the same problem and he dosn't even knows how to flash a rom...
Also i know is not a batery issue because the phone wont reboot on Recovery or either fastboot mode for hours...
Here is a video so you can see what i'm talking about.
https : / / drive . google . com / file / d / 1gpPkLcR -HJIhEhB46JZ4voMWnQcbQdiU / view ? usp = sharing
scriiby said:
Hello , ive been facing this problem since 2 days ago working day and night to fix it and i didnt found a way to do it.
All started with a Hard brick that detected the device as Diagnostic 900E i did a test point and solve it so easy, then i installed a rom a android 8.0 rom and here is where the problem begun.
It looks like it was all perfect i started with the initial configuration, but when it went for select the wifi the phone reboots all the time. I tried to skip every config and managed to get on the sistem but then it reboots over and over every 1 or 2 min the phone reboots by himself. I flashed a lot of roms and none of them works , wiped everything from normal recovery and twrp and nothing. Does anyone has any info of this issue? A friend of mine who also bought a mia1 had the same problem and he dosn't even knows how to flash a rom...
Also i know is not a batery issue because the phone wont reboot on Recovery or either fastboot mode for hours...
Here is a video so you can see what i'm talking about.
https : / / drive . google . com / file / d / 1gpPkLcR -HJIhEhB46JZ4voMWnQcbQdiU / view ? usp = sharing
Click to expand...
Click to collapse
Bro you chooses wrong script in mi flash
That deleted your imei
Give me your whatsapp or telegram for furthe discussion
I guess I have the same problem maybe i don't have an imei anymore, I should check :
https://forum.xda-developers.com/mi-a1/help/help-stucked-weird-bootloop-flashing-t3721142/page3
https://forum.xda-developers.com/mi-a1/help/mi-a1-imei-help-please-t3742245
https://forum.xda-developers.com/mi-a1/help/ruined-modem-partition-please-help-t3733909
go through this threads bro, you will revive your device for sure good luck mate
Bro persist partition repair fixxed restart problem
Have you solve this?
Write persist in twrp... Search the forum for the persist and guide...
For me writing persist didnt work till i had to switch from slot A to slot B in twrp then phone booted