Related
Hi, I bought a Sony Ericsson Xperia X2 and decided to update the firmware through SE Update Suite. In the middle of firmware update, the computer BSoDed on me. The phone went dead and the PC did not detect it any more (Unknown USB device in device manager).
Eventually I managed to detect the phone by SEUS (on another machine); now I have a "COMXX SSE X2 Software DOWNLOAD" in device manager. I follow the instructions in SEUS to update the firmware, press and hold Vol Down + Power buttons. The phone vibrates and device manager shows "COMXX SE X2 Software DOWNLOAD", but SEUS does not update the phone.
What can I do to recover the phone?
update firmware
How can I update firmware from card?
bdadabayev said:
How can I update firmware from card?
Click to expand...
Click to collapse
???
You have to do it through SEUS.
don't worry
this happened to me too. heres what you do read all the steps before you do it
first go ahead and charge you phone just plug it into the wall then follow these directions
1.) start suess and continue like you normally would
2.) remove your battery cover and leave it off
2.) when you get to the step that asks you to plug in your phone, connect your phone via usb to you computer, then hold the down volume button + the power button + while you are holding these buttons push the soft restart button* do this all at once and do not let go of any of the buttons until you see the white screen with the sony ericson logo and it should update like normal.
*to get to the soft restart look at the back of the phone with the battery cover off, now pull out the stylus right there next to you camera where you stylus came out is a little button push it with your stylus.
this worked for me when i thought i bricked my phone and it worked, so good luck and tell me how it works out
doministry said:
???
You have to do it through SEUS.
Click to expand...
Click to collapse
Can I flash without SEUS, other methods?
yummy-fun said:
this happened to me too. heres what you do read all the steps before you do it
first go ahead and charge you phone just plug it into the wall then follow these directions
1.) start suess and continue like you normally would
2.) remove your battery cover and leave it off
2.) when you get to the step that asks you to plug in your phone, connect your phone via usb to you computer, then hold the down volume button + the power button + while you are holding these buttons push the soft restart button* do this all at once and do not let go of any of the buttons until you see the white screen with the sony ericson logo and it should update like normal.
*to get to the soft restart look at the back of the phone with the battery cover off, now pull out the stylus right there next to you camera where you stylus came out is a little button push it with your stylus.
this worked for me when i thought i bricked my phone and it worked, so good luck and tell me how it works out
Click to expand...
Click to collapse
doesn't wurk, device unknown maybe you didn't brick your phone, that's why it was still booting to logo screen...
I noticed that "COMXX SSE X2 Software DOWNLOAD" device appears in Device manager when the Volume UP is pressed on boot instead of Volume DOWN.
One more thing... There is a useful piece of software out there called QPST (Qualcomm Phone Service Tool). When I have the phone in download mode it detects the device (since it's Qualcomm platform, pretty much like ZTE 3G modems). But I don't have loaders or software to flash the phone baseband from QPST. Maybe if someone can parse the firmware available on the Net and extract the said loaders and software, then I could flash the Baseband and get the phone detected by SEUS to continue flashing Windows part. Unfortunately, decrypting the firmware is way beyond my knowledge. Anyone more knowledgeable on this subject?
First of all: Charge your phone for at least 2 hours from wall charger. I have experienced that it does not charge from USB always, especially when in update mode.
Please try this if you have only charged from USB previously.
Prydplante said:
First of all: Charge your phone for at least 2 hours from wall charger. I have experienced that it does not charge from USB always, especially when in update mode.
Please try this if you have only charged from USB previously.
Click to expand...
Click to collapse
Thanks for your advice, but I am aware that phones don't always get full charge with damaged firmware. That is why I took the battery out and charged it fully with a special charger for batteries.
Need help
Can anybody help? - Problem is that i cant "push" my phone to go to bootloader (tried soft-reset, vol down+shut down..nothing helps), so it i cant update via SEUS. And after trying to instal manualy R3 cab's, "Clear phone memory" is gone - now i even can't reset my phone.
Anybody, please help.
what i think you trying to do is boot the rom from the sd card is that right? if you are, it won't work because you need a alternative bootloader or a hard-spl which the x2 doesn't have... yet. thats why we HAVE to use SUES. if you can't get your computer to recognize your phone even after charging it in you special charger and forcing it into bootloader via SUESS (the option i pitched earlier) your best bet is to contact Sony Ericsson or who ever you bought it from and tell them they sold you a faulty device and they HAVE to replace it. if you get the opportunity to talk to them on the phone be firm and don't ever place fault on yourself and push that they sold you a broken device, hopefully they will send you a new one. i'm sorry i couldn't help. At this time my knowledge in Winmo is ignorant at best. good luck
anyone know how to help?? i also have this problem.... ><
Down volume button + the power button doesn't have the logo of SE..
and the SEUS can't detect my x2... wanna cry//
Hi!
Do exactly like this:
1 Charge the battery with the wall charger to at least 50.
2 Remove all cables connected to X2. This is important!
3 Remove and re-insert battery.
4 Push and hold volume down.
5 While still holding volume down, push and hold Power at the same time.
6 Hold until SE logo on white background appears, then release both buttons.
7 Now connect USB cable.
Be careful to follow this exactly or it will not work!
x2 prob
I have same problem in my phone , during update with SEUS computer hang and now
my phone shows only vibrate.
i have tried volume down+power+reset
but it can't go to white screen or sonyericsson logo.
any other solution
bdadabayev said:
Thanks for your advice, but I am aware that phones don't always get full charge with damaged firmware. That is why I took the battery out and charged it fully with a special charger for batteries.
Click to expand...
Click to collapse
Or You might need go to " C " drive - Progam files _ sony Ericson than remove any SEUS in that folder befor you go to inStall new F/Ware up date , everytime you want to reflash new SEUS you have to remove the last time F/Ware evenly that is the same one SEUS .than you go on for update new F/Ware SEUS to your phone .
Here is the support site for US. SE has a dedicated Nr and mail for x2.
what about new's for xperia x2 flashing
i have one stuck on logo after installing cab
and seus say's that no new update
Rise said:
I have same problem in my phone , during update with SEUS computer hang and now
my phone shows only vibrate.
i have tried volume down+power+reset
but it can't go to white screen or sonyericsson logo.
any other solution
Click to expand...
Click to collapse
same problem i have
is there anythng new?
what to do is any way to fix it?
X2 morto !!!
I have the same problem, now I try to modify the language of my phone, just missing to finish the installation program displayed an error message and now I can not in flash mode puts you ... what friends do?
I have an p700 with cm10( last version ), cmw touch last version, crossbreeder and first version of custom kernel (without oc). Run perfectly until yesterday. I intended to flash new kernel (V4). Battery was at 9 percent full. Reboot in recovery mode and... shock ... black screen. My phone is dead. Nothing... no power, no joy....
Thank you for help...
Sent from my Galaxy Nexus using Tapatalk 2
did your charge it? did it boot? can you enter recovery or emergency?
and why did you flash with only 9%?!?
h4x0r007 said:
did your charge it? did it boot? can you enter recovery or emergency?
and why did you flash with only 9%?!?
Click to expand...
Click to collapse
From my experience with p500 (optimus one) 9% battery it more then enough for flash an kernel ... but it seems that 9% was not for real (first version of custom kernel has problem with battery status). Anyway ... after I downloaded the new kernel (v4), from reboot menu (cm10) I gave the reboot recovery command ... "Rebooting now" ... and ... instead of recovery mode, the phone was powered off. So I never got to flash ... Now it's dead, does nothing ... No power (with or without battery and the power cord plugged in), no recovery mode, no emergency mode, no charging.
I used original charger (0,75 A), after that an Samsung charger (1 A), after that an Logitech charger (1.5A).
I tryed to charge with my laptop from USB 2.0 port and 3.0 port, and with my desktop computer ( USB 2.0, 3.0 )... All I've got is THE BIG NOTHING.
Thank you for replay...
It just happen to Me..!
Recently it works fine and I did nothing..
Battry on 66%, and try to refresh the system via reboot.
Few seconds, screenlight turn off.
I've keep waiting. it usualy showing LG logo after 10seconds.
But nothing happen.
Try to power on and also try CMW shortcut.
It still blackscreen, no vibrate, no light.
Is there a way out of here? or any solutions?
:sad:
gefademe2d said:
It just happen to Me..!
Recently it works fine and I did nothing..
Battry on 66%, and try to refresh the system via reboot.
Few seconds, screenlight turn off.
I've keep waiting. it usualy showing LG logo after 10seconds.
But nothing happen.
Try to power on and also try CMW shortcut.
It still blackscreen, no vibrate, no light.
Is there a way out of here? or any solutions?
:sad:
Click to expand...
Click to collapse
Unfortunately, the only way to bring it to life is JTAG. I paid ~ 35Euro for JTAG-ing.
damn
damn i want cm10 too, bet im to scared with bootloader unlocking etc after reading posts...
Its happend to me too and i found a way to get out there
Tip: NEXT TIME DO NOT INSTALL ANY KERNEL!!!
This is the solution:
1. Download LG Optimus L7 USB Driver for Windows | Mac
Download official LG Optimus L7 stock firmware from this page. The file would be a .kdz file. Download the appropriate firmware according to your network provider and country.
3. Download KDZ updater and install it on your computer.
4.The zip file has a Microsoft XML parser, make sure you run it as an administrator and restart your PC. This will solve the wparam 100 and lparam 6 issue mentioned in a comment below.
5.The next step is to put your phone into emergency mode. To do this, remove the battery of your phone and re-insert it (don’t turn it on). Press and hold Volume Up button and Volume Down button. While you are pressing the two buttons, press the Power button. So now, you must be pressing all three buttons together. See this video
6.Your phone will boot into emergency mode and you should see a yellow screen with Emergency mode written on it.
7.Pick up the USB Cable and connect your phone to the computer via the USB Cable.
8.Run KDZ updater as Administrator.
9.Choose the following options in KDZ Updater: Type: 3GQCT Phone Mode: DIAG and KDZ file is the one you downloaded in step 3.
*image:
http://www.hackmyandroid.com/wp-content/uploads/2012/09/Root-LG-P350-LG-Update.png
10.Re-check with the image above and ensure that you have the appropriate settings on the KDZ updater.
11.Take a deep breath and click on “Launch Software Update” button.
12.This process is usually long. It take quite a long time for the firmware to be flashed on your phone.
13.If everything goes well, you will see “Finished” written in the log screen and your phone will change to switched off mode from Emergency mode.
14.The next time you turn it on, your phone will take a lot of time to reboot. Stay Cool! its normal.
david08 said:
Its happend to me too and i found a way to get out there
Tip: NEXT TIME DO NOT INSTALL ANY KERNEL!!!
This is the solution:
1. Download LG Optimus L7 USB Driver for .......
Click to expand...
Click to collapse
I knew this method ... but in my case, the phone does not respond to any command.
heruur2 said:
I knew this method ... but in my case, the phone does not respond to any command.
Click to expand...
Click to collapse
When you turn on your phone that shows you the LG logo?
david08 said:
When you turn on your phone that shows you the LG logo?
Click to expand...
Click to collapse
It has no power...
heruur2 said:
It has no power...
Click to expand...
Click to collapse
Connect the device into electricity and not to your computer.
For 1 hour and try again
david08 said:
Connect the device into electricity and not to your computer.
For 1 hour and try again
Click to expand...
Click to collapse
Thank you for help...
BUT...
I try already for many hours, with 3 type of chargers... (0.75A - original charger, 1A and 1.5A)...
As i told in my previews post ... Now it works ... After JTAG-ing...
david08 said:
Its happend to me too and i found a way to get out there
4.The zip file has a Microsoft XML parser, make sure you run it as an administrator and restart your PC. This will solve the wparam 100 and lparam
Click to expand...
Click to collapse
It is not possible to run that file as an administrator. I tried on 3 different systems: Win 8x64, Win 7x64 and Win 7x32. I have a logo stucked but after few seconds it plays the sound and logo does it's animation then same static logo and then it stucks. Is there any solution besides j-taging? Does warranty service cover this as a defect and repair for free?
Thanks
Kastuvasesi said:
It is not possible to run that file as an administrator. I tried on 3 different systems: Win 8x64, Win 7x64 and Win 7x32. I have a logo stucked but after few seconds it plays the sound and logo does it's animation then same static logo and then it stucks. Is there any solution besides j-taging? Does warranty service cover this as a defect and repair for free?
Thanks
Click to expand...
Click to collapse
Try hard reset :
1. When the phone is switched off, press and hold the Volume down key + Power key with your left hand.
2. When the LED on the bottom of the phone lights up, touch and hold the Menu key with your right hand. You need to do this immediately, before the screen displays the LG logo. Make sure your left hand is still holding the Volume down and Power keys.
Then release the power key at vibration time.
3. When the LG logo is displayed on the screen, continue to hold the keys for around 2 seconds, and then release all
them at the same time, before the LG logo disappears.
Leave your phone for at least a minute while the hard reset is carried out. You will then be able to switch your phone back on.
Caution: If you perform a hard reset, all user applications and user data will be deleted. This cannot be reversed.
Hi all,
I've tried to downgrade my S5 from most recent Kies lolipop to kitkat (G900FxxxANCE from sammobile). After odin pass the phone reboots (at leas it seems so) but does not show up on screen - so screen is black and no chance to do anything - the blued led comes up.
I tried some tutorials without success (last try: remove battery - powerbutton - wait). Do you
a) know whether it is a soft or hard brick?
b) any workaround?
If you answer to this I would be very glad since I'm currently a bit nervous.
Thank you and regards so far.
snikk said:
Hi all,
I've tried to downgrade my S5 from most recent Kies lolipop to kitkat (G900FxxxANCE from sammobile). After odin pass the phone reboots (at leas it seems so) but does not show up on screen - so screen is black and no chance to do anything - the blued led comes up.
Thank you and regards so far.
Click to expand...
Click to collapse
Can you still enter Download Mode, and Recovery Mode?
Uzair40 said:
Can you still enter Download Mode, and Recovery Mode?
Click to expand...
Click to collapse
No, not really. Or I don't really know since the screen doesnt show anything. I've read that the blue led stands for entering download mode.
Well, at least odin recognizes the phone when plugging in while the blue led is on.
If you had a successful odin flash, you should have a recovery.....
You need to (at least) try to get into recovery.....sometimes, in cases like this, wiping cache and factory resetting (maybe a couple of times) is enough to get the phone to reboot......
If it doesn't work, going to download mode and re flashing your LP firmware may be necessary.......
http://i.imgur.com/rVnFwJM.jpg
keithross39 said:
If you had a successful odin flash, you should have a recovery.....
(...)
If it doesn't work, going to download mode and re flashing your LP firmware may be necessary.......
Click to expand...
Click to collapse
The screen is plain dead. It does not react in any way. When I "start" the phone I don't see anything except the blue led in the upper left corner on the phone itself.
I'm not sure if its booting into recovery (I've read that the blue led stands for recovery mode though).
The only thing I recognize is the successfull connection in Odin but I can't flash again since it hungs in "Connecting..."-state.
Regards.
snikk said:
The screen is plain dead. It does not react in any way. When I "start" the phone I don't see anything except the blue led in the upper left corner on the phone itself.
I'm not sure if its booting into recovery (I've read that the blue led stands for recovery mode though).
The only thing I recognize is the successfull connection in Odin but I can't flash again since it hungs in "Connecting..."-state.
Regards.
Click to expand...
Click to collapse
Remove the battery so you know 100% the phone is off
Replace battery
Press and hold Power Down & Home & Power until it enters download mode
If nothing appears on the screen after a few seconds (Give it about 5+ seconds of holding the buttons down), then it is likely a hardware issue
Possibly the phone itself, but also possible one of those buttons is not working
*Detection* said:
If nothing appears on the screen after a few seconds (Give it about 5+ seconds of holding the buttons down), then it is likely a hardware issue
Click to expand...
Click to collapse
Thank you. It didn't work in any way. I've tried to connect via ADB and factory reset but I can't establish a ADB connection. I connect the device and windows tells me "Installing drivers" (Drivers are installed) but fails in the end. So I guess this is the fault. Whatever.
I can't tell in which state the phone boots as I only see the blue led (its just turned on - no blinking).
snikk said:
Thank you. It didn't work in any way. I've tried to connect via ADB and factory reset but I can't establish a ADB connection. I connect the device and windows tells me "Installing drivers" (Drivers are installed) but fails in the end. So I guess this is the fault. Whatever.
I can't tell in which state the phone boots as I only see the blue led (its just turned on - no blinking).
Click to expand...
Click to collapse
Sounds like it's time for the old repair shop unfortunately
i have had the same problem when i downgrade to kitkat to fix it download a lollipop rom from sammobile then u have to :
-remove battery put it back
-press Home + Power + Volume Down buttons
-screen will be black no problem press up arrow to continue to download mode
-connect phone to usb
-open odin u will see it is connected
-flash lollipop and u will be back
i think it is a restriction for lollipop because u will root the phone on kitkat with tw.apk
if this not will help i have another solution just try it same problem to me and i figured my self to fix the problem
Hi all,
i have the same probleme with my sam G5.
after flashing back the lolipop stock rom 5.0 the phone seems to be working properly except for the screen that shows nothing; windows detects it as MTP device and i can get in and see all the content inside of it, also when i assimilate entering the download mode (volume down + Home + power then after few secondes Vol up) it goes well since odin detects it and flash it (but always there is nothing that shows up on the screen),
any ideas or hints ??
If you want to downgrade to kitkat from lollipop,then flash kitkat modem and bootloader for your device,you can search on the xtrestolite post,the developer put bootloaders and modems for each g900* device for kitkat and lollipop roms.
Hi
i bought before 2 weeks Xiaomi a1
it wored very good.
Today while I wanted to turn on the screen it did not respond.
The phone is not responding to any type of pressing.
I must say that the phone is new, did not get any kind of hit , and 5 min before this problem it used to work really good.
I think that the phone is in brick mode, and i can't enter to fastboot option because the phone is not responding....
Pls help my solve this problem.
Thanks
Try holding the pwoer button for more then 10 seconds, that should reset it... once you start it up aghain turn of ambient screen... Gave me troubles too... Hope that helps.
Has that still not been fixed with November update? I turned my ambient screen back on to see. So far, 2 days since update and no black screen after notification.
I'm guessing it's not dead. I have the same problem before as well. It was the buggy Ambient Display. Force restart your phone by pressing power button and holding it more than 10 second. First thing on boot up complete, go to Settings > Display and turn off Ambient Display.
micleftic said:
Try holding the pwoer button for more then 10 seconds, that should reset it... once you start it up aghain turn of ambient screen... Gave me troubles too... Hope that helps.
Click to expand...
Click to collapse
I cant even turn on the screen...
It's not showing any thing on the screen.
I tried to push the power but there is no respond
myself379 said:
I'm guessing it's not dead. I have the same problem before as well. It was the buggy Ambient Display. Force restart your phone by pressing power button and holding it more than 10 second. First thing on boot up complete, go to Settings > Display and turn off Ambient Display.
Click to expand...
Click to collapse
I tried forcing it. But it is still show black screen.
I think it is in brick mode
roy123456 said:
I tried forcing it. But it is still show black screen.
I think it is in brick mode
Click to expand...
Click to collapse
Just go in fastboot mode and reflash the firmware from MIUI.con
jack_21 said:
Just go in fastboot mode and reflash the firmware from MIUI.con
Click to expand...
Click to collapse
How can I enter the fastboot mode?
I cant even turn it on.
It is not respoding.
I tried to put it on this mode but the screen is still black.
roy123456 said:
How can I enter the fastboot mode?
I cant even turn it on.
It is not respoding.
I tried to put it on this mode but the screen is still black.
Click to expand...
Click to collapse
You must keep pressed vol down + power until the phone does show "FASTBOOT"
jack_21 said:
You must keep pressed vol down + power until the phone does show "FASTBOOT"
Click to expand...
Click to collapse
How long?
I tried it for 3 min ...
Is it enough?
roy123456 said:
How long?
I tried it for 3 min ...
Is it enough?
Click to expand...
Click to collapse
Well there is something strange.
Leave the phone discharge
Then let it charge
Then power on with vol down + power
Try these 2 things
1) charge your phone for 2-3 hours. if didnt switch on try this 2
2) Connect your data cable with pc. In mobile Press volume up + volume down and plug in the other end of usb cable to your mobile. you need to hold the keys. this will boot your phone into fastboot.
If boot steps didnt work then it might be a hardware problem or hard brick.
selvarajrajkanna said:
Try these 2 things
1) charge your phone for 2-3 hours. if didnt switch on try this 2
2) Connect your data cable with pc. In mobile Press volume up + volume down and plug in the other end of usb cable to your mobile. you need to hold the keys. this will boot your phone into fastboot.
If boot steps didnt work then it might be a hardware problem or hard brick.
Click to expand...
Click to collapse
What can I do if it is a hard brick?
roy123456 said:
What can I do if it is a hard brick?
Click to expand...
Click to collapse
Visit customer care(they will probably say motherboard problem as always) or try qfil method which is quite complex if this flashing things are new to you.
roy123456 said:
How long?
I tried it for 3 min ...
Is it enough?
Click to expand...
Click to collapse
you should press the power key while charging cable connected.If it doesn't work , unplug the charging usb and plug again reverse(type c's reversibility).If it can't, try with another AC source,another person,another location.
My A1 reborn by my gf's charging adaptor,hand and location.(she know nothing about android hard key combination)
Just thinking,don't know exactly.Sorry for my english.
My was hang.. so I restarted it.. but aftr tht.. phone is not turning on.. its just showing anroid one.. and nothhing else
ruhi maallivk said:
My was hang.. so I restarted it.. but aftr tht.. phone is not turning on.. its just showing anroid one.. and nothhing else
Click to expand...
Click to collapse
reflash phone with stock firmware in fastboot mode on MI FLASH TOOL
selvarajrajkanna said:
Try these 2 things
1) charge your phone for 2-3 hours. if didnt switch on try this 2
2) Connect your data cable with pc. In mobile Press volume up + volume down and plug in the other end of usb cable to your mobile. you need to hold the keys. this will boot your phone into fastboot.
If boot steps didnt work then it might be a hardware problem or hard brick.
Click to expand...
Click to collapse
I need help on urgent basis
I'm using Mi A1 rooted with custom kernel, My phone automatically received august update and it's installed automatically then i try to go in download mode to flash my phone with stock rom but i didn't press volume button properly and it's get restart and automatically start installing august update and i by mistake press power button and now my phone is not turning on even not responding
when i try to connect my phone with pc i can hear the connect sound but it's not going in fast boot
Shivam.S said:
I need help on urgent basis
I'm using Mi A1 rooted with custom kernel, My phone automatically received august update and it's installed automatically then i try to go in download mode to flash my phone with stock rom but i didn't press volume button properly and it's get restart and automatically start installing august update and i by mistake press power button and now my phone is not turning on even not responding
when i try to connect my phone with pc i can hear the connect sound but it's not going in fast boot
Click to expand...
Click to collapse
You switched off the phone in middle of installing ota, best bet is take it to the take it to the service center and tell them phone not switching back on after installing August ota update.
Or if not in warranty then try to install stock rom using qfil.
Unfortunately you have bricked your Mi A1
Shivam.S said:
I need help on urgent basis
I'm using Mi A1 rooted with custom kernel, My phone automatically received august update and it's installed automatically then i try to go in download mode to flash my phone with stock rom but i didn't press volume button properly and it's get restart and automatically start installing august update and i by mistake press power button and now my phone is not turning on even not responding
when i try to connect my phone with pc i can hear the connect sound but it's not going in fast boot
Click to expand...
Click to collapse
You have bricked your Mi A1, when you turned it off while installing/flashing the August update. Basically you should never turn a smartphone off, or disconnect the USB cable (if it is connected), while flashing its ROM.
There are various methods to unbrick it, I suggest you try this one since it's apparently not going into fast boot:
[Experimental]Recover Hard Bricked Xiaomi A1 Using SD Card
Hi, I get this phone yesturday... I've installed last firemware ( 6.0 to 7.0.1 ) and after I tried with Tuliptool to install recovery but after this my phone dont show recovery when I tried so I was thinking I've forget to Unlock it before... and obvously I tried to unlock ( with tulip ) but I got error message in cmd ( I don't remerber... ) and now it show only Zte and it bootloop on it so I didn't have recovery, I can't use edl because I can't boot.. so there is something I can do or I bricked it in less than 1 day.. ? :S
Got the same problem
EDL can only be entered once the phone is completely off. You need to hold down volume up + volume down and then plug in the usb cable (dont touch the power button). The phone wont do anything, it will still look off but you will hear the device plugged in tone in Windows and will be able to find the device in zadiag. Also after a few attempts Windows stopped showing the device and I had to restart Windows before it worked again. Can you get this far?
dmo199 said:
EDL can only be entered once the phone is completely off. You need to hold down volume up + volume down and then plug in the usb cable (dont touch the power button). The phone wont do anything, it will still look off but you will hear the device plugged in tone in Windows and will be able to find the device in zadiag. Also after a few attempts Windows stopped showing the device and I had to restart Windows before it worked again. Can you get this far?
Click to expand...
Click to collapse
no my phone is just showing ZTE when it is booting then just instant turns off and starts again showing ZTE and it is doing that until the battery is empty
I did have that before, I'm not sure the exact combination I used, charge it up and then remove the cable, hold the power button and either the volume up, or volume down or both for anywhere between 5 and 20 seconds before letting go and seeing if it stays off. If it doesn't work try again and again and again, Its completely trial and error and took me a while to get it to work
dmo199 said:
EDL can only be entered once the phone is completely off. You need to hold down volume up + volume down and then plug in the usb cable (dont touch the power button). The phone wont do anything, it will still look off but you will hear the device plugged in tone in Windows and will be able to find the device in zadiag. Also after a few attempts Windows stopped showing the device and I had to restart Windows before it worked again. Can you get this far?
Click to expand...
Click to collapse
I'm not quite sure but on the European version of the Axon you can't do that by holding the buttons.
I understand that the only way to get in edl mode is software, no other choice than rebooting from the OS using the command adb reboot edl. So if you can't make your device completely started first, i guess it's bricked. But maybe i'm totally wrong.
vincent1967 said:
I'm not quite sure but on the European version of the Axon you can't do that by holding the buttons.
I understand that the only way to get in edl mode is software, no other choice than rebooting from the OS using the command adb reboot edl. So if you can't make your device completely started first, i guess it's bricked. But maybe i'm totally wrong.
Click to expand...
Click to collapse
I also messed up mine. I did everything until I had android 7, rooted, but lost IMEI. then I, THE IDIOT, tried to re-flash stcok android 6......booom. bricked.......
however.........power the phone off:
hold vol- power for 10 secs. phone should boot into FTM. then power it off by pressing power for about 5 secs. phone is off.
now vol+power and the phone should go to recovery, even if stuck on the logo, my pc reads it as recovery in adb devices......
tomorrow I'll see if I can get out from there. my experience doing this before is that from the recovery the ADB reboot edl works
cheers