Database Users

Rogers focus stuck in loop... Any ideas?

I too have a focus that is stuck in a loop at the Samsung logo. I bought it like that thinking I might be able to resurrect it as another toy. I have had lots of experience with Samsung, HTC and Sony droid phones, this would be the first WP.
It is a I917R on Rogers, there is no hardware revision under battery. I am assuming it is V1.3 as I have only seen software for the that version posted. I do not know how the phone got to its present state. They just said it happened during normal use?
I can get to both download mode and factory reset. I have flashed the stock rogers files without errors, but I never get the screen connecting to pc. The phone just restarts after successfully flashing, only to reboot continuously. I have been able to install MAGLDR and flashed every v1.3 ROM i could download. All without errors, just the same outcome they all just keep displaying Samung logo and then reboot. Only thing I noticed is that when I flash MAGLDR and custom ROMs it takes the phone longer to reboot.
I never get the connect to pc if I hold camera and power, nor do I ever get that screen when I flash a ROM.
Not sure if situation is similar... I am puzzled?

Your situation is very similar with other folks' here, unfortunately. It's not clear what causes it and there's no solution as of yet. For some, re-flashing worked. For others, a new battery. Most are stuck on loop...
When you connect the phone to USB when in download mode, what do you get?

When I boot to download mode I can flash Rom with WP7. I get to the yellow triangle download mode and flashes ok, no errors. Just noticed that it never goes to connect to pc mode.
Same with when I format, no connect to pc mode.
Nothing I try seems to help.

blackangel21 said:
When I boot to download mode I can flash Rom with WP7. I get to the yellow triangle download mode and flashes ok, no errors. Just noticed that it never goes to connect to pc mode.
Same with when I format, no connect to pc mode.
Nothing I try seems to help.
Click to expand...
Click to collapse
I see. What messages do you get when you connect the phone to the PC via USB, in either mode?

No messages, just shows up as Samsung USB composite device, Samsung mobile modem and Samsung mobile modem diagnostic serial port in download mode.
In magldr it shows up add Microsoft USB sync.
The only thing I forgot to mention was that when I flash with WP7 it finished without error in 90 seconds, but on the phone it says it will take 10 minutes.

Not sure what more I can add...
You could try different downloaders. Please see this thread for 7.41 downloader, maybe that helps?

Tried both, same outcome... No errors, just keeps rebooting... No Connect to PC message.

Im having the same problem. And i can see many other people who are having the same issue also. So i think its time to dump those phones, not worth a penny. The one i have in here was actually working, i followed all the directions in order to flash it. And still the phone got stuck into that bootloop. Its ridiculous from what i can see. I think ive read once you put that SDmini in it the phone will use it for the OS. But the one i had was working actually without it, i could turn it off as many times as i wanted and nothing happened. But if i tried a factory reset data would stay and diagnosis mode wasnt working. So i decided to flash it. Big, huge mistake! Hope you have better luck than i did. Because im dumping this one....

Same problem here, ive checked a couple of threads and no solution so far

GS4 Softbrick only boots into odin mode help!

Hello guys i was trying out the new Kangabean 4.3. ROM for my AT&T and after flashing it in TWRP it appears I has softbricked my device. I can only boot into download (odin) mode and it stays on "downloading now".. Anyhow i cannot boot into recovery it just vibrates to confirm my input and just revibrates and revibrates... Looked all over for guides and tried to return it to factory settings on Kies but it does not detect my phone... Any help would be great i need this phone for work everyday!!!

Karbooo said:
Hello guys i was trying out the new Kangabean 4.3. ROM for my AT&T and after flashing it in TWRP it appears I has softbricked my device. I can only boot into download (odin) mode and it stays on "downloading now".. Anyhow i cannot boot into recovery it just vibrates to confirm my input and just revibrates and revibrates... Looked all over for guides and tried to return it to factory settings on Kies but it does not detect my phone... Any help would be great i need this phone for work everyday!!!
Click to expand...
Click to collapse
Please search for similar threads. This same issue is being posted over and over and over again. When you were making this post, what "similar threads" or "similar topics" showed up? Did you check them for a solution?

yes sorry i looked at all of them and they all involved well just flashing the stock rom but i cant get my computer to see my gs4 on download mode...i got the drivers and odin installed.

Well, this thread has a couple of ideas...
http://forum.xda-developers.com/showthread.php?t=2405991
or maybe here...
http://forum.xda-developers.com/showthread.php?t=2405127
You might also want to look at the TWRP thread in the development section.
Try again to get into recovery, the key sequence can be tricky, make sure you are doing it just right. "Doing it just right" has been discussed many times.
Also, look at this thread, maybe it will help...
http://forum.xda-developers.com/showthread.php?t=2398336
Yea, I realize that thread is about MF3, but it still has ideas that might help you.
There are also a ton of threads about how to get your PC to recognize ODIN.....search.......good luck.

yeah ive been at it for hours man those links can all access the recovery i cant... i tried everything got the drivers up tried all the odins and its just stuck on "downloading do not turn off target" and my pc doesnt see it...

Odin finally recognized it on the pc in download mode and i was able to flash the stock rom but it seems it wasnts successful...it still just vibrates and vibrates when i press the power...

Try flashing the open recovery.
Sent from a jedi extacy note II

If you mean the CWM recovery I tried it on Odin and it failed.... :""(
Sent from my Nexus 7 using xda premium

Take battery out, back in, power+volumedown, download mode, Install Samsung Kies, do Kies update, connect to PC, Tools-> firmware initialization, take battery out and type model/serial Number, wait patiently until it finishes.
Try different USB port or different PC. Use stock USB cable comes with original box.
If Kies screen get stuck at model number section, you did flash MF3 triangle thingy -> unsolveable brick. Have to go thorugh warranty replacement.
Sent from my SGH-I337 using Tapatalk 4

the Kies Emergency firmware utility worked it put my phone like the day i bought it...also rooted it successfully and installed TWRP on it thanks guys

Samsung GTi9505 stuck in boot loop.

Hi, first time here so sorry if in wrong place.
so my s4 has gone into a boot loop, it wont get past the first samsung screen before rebooting.
things i have tried; going into safe mode, no luck.
going into recovery mode, no luck
trying, to wipe it by holding down volume up, home and power, still nothing.
the screen will sometimes artifact whilst stuck in the boot loop.
so i looked into trying to use odin to flash the phone back to stock, as im using lollipop. odin won't even recognise my phone.
the phone is no longer under warranty.

Bump

For Odin to recognise your phone you need to boot into download mode. You also need the samsung drivers installed.
Also try different usb ports and cables.

GDReaper said:
For Odin to recognise your phone you need to boot into download mode. You also need the samsung drivers installed.
Also try different usb ports and cables.
Click to expand...
Click to collapse
tried 9 different ports, 3 different cables, my drivers are up to date. it can connect to my gf phone.

jebbles said:
tried 9 different ports, 3 different cables, my drivers are up to date. it can connect to my gf phone.
Click to expand...
Click to collapse
bought a new cable, and finnally got to connect to my pc!! twrp installed.
in the vol.up+power to get to recovery. i have 3 lines
its stuck on this.
top blue: recovery booting....
middle red; recovery is not seandroid enforcing
bottom yellow; set warranty bit : recovery

I suggest you flash a stock rom and go from there.

my phone isn't allowing me to flash a rom http://imgur.com/Lkkmqyz

ok, so i talked to samsung support, looks like the mainboard is moslty likely the culprit and they said it will need replacing $250...
funeral service for my phone will be held at 1pm gmt +10.30
thanks for your help though.

Buying an S4 with a broken screen and switching the motherboards would be cheaper.

Bootloop, No recovery and No download Mode.

Hello,
I was trying to flash Twrp recovery in my phone using flashify. It said flash successfully and i rebooted. It starting bootlooping. I manually tried by pressing Volume up + Home+Power keys it was still doing bootloop. I tried to goto download mode by pressing Volume Down+ Home+Power keys it still kept bootlooping even USB jig didn't work. I need your valued suggestion about what to do next.
Thanks in Advance.
I have Samsung Galaxy Grand Primr G530H
here is video link youtu.be/B_EtRTH93YE

Just flash your firmware from Odin using a PC, I had a similar problem in my tablet, it didn't had download mode either and that worked, try it.

When I connect it to Pc it keeps bootlooping and pc gives sound of connecting then disconnecting of hardware.

GorJessSpazzer said:
Just flash your firmware from Odin using a PC, I had a similar problem in my tablet, it didn't had download mode either and that worked, try it.
Click to expand...
Click to collapse
How did you flash a firmware, when your tablet didn't have download mode? What ODIN version did you use? please tell us we need your experience.

talvigi said:
How did you flash a firmware, when your tablet didn't have download mode? What ODIN version did you use? please tell us we need your experience.
Click to expand...
Click to collapse
Turn off your device, keep your finger in the button until the device is off or pull off the battery, connect it to the PC and flash your firmware through Odin, at that moment I used the 3.70 i think but you can use the latest version it's fine, that should install download mode and the whole firmware if that doesn't work I'm afraid I don't know how else I can help, that's what I did and it worked

GorJessSpazzer said:
Turn off your device, keep your finger in the button until the device is off or pull off the battery, connect it to the PC and flash your firmware through Odin, at that moment I used the 3.70 i think but you can use the latest version it's fine, that should install download mode and the whole firmware if that doesn't work I'm afraid I don't know how else I can help, that's what I did and it worked
Click to expand...
Click to collapse
You are right I did it the same way and it worked for me too. I actually was thinking the phone was quite dead bur or wasn't, I just flashed the recovery firmware 4.4.4 Russian and if you ask me food the step by step procedure it was just like this:
1. I started the Odin 3.07 and connected my device to see is it was detected or not, my surprise the Odin catch it, and shown added and the port number was 18.
2. I just pulled out the USB cable from my laptop and loaded the BL file only to just flash the bootloader file and see what would happen, I was trying it bcz I was totally disappointed with the device i.e. Grand Prime 530H Duos. I also noticed that my device was not stable even with that black screen it used to restart after almost five minutes in that case. And I knew that in 5 minute I will just be able to flash BL file. The BL file was loaded on the Odin now and I inserted the USB cable again while keeping the vol down button pressed to my laptop when the Odin again found and connected with my device, I didnot take any more time to flash BL file.
3. As soon as i had not flashed all the SW therefore, my device didn't boot properly, and I thought it didn't work but when my device was connected to the computer I just listened the startup tone of the Android 4.4.4. From that moment I knew my device was not dead now so i had to select all four files from the recovery firmware of 4.4.4 and connect the device to odin even there was no sign of download mode, as soon i clicked the Start button i saw many things in the Odin which were good enough to see. after the firmware flashed the device got started.
Sent from my SAMSUNG-SM-G920A using Tapatalk

talvigi said:
You are right I did it the same way and it worked for me too. I actually was thinking the phone was quite dead bur or wasn't, I just flashed the recovery firmware 4.4.4 Russian and if you ask me food the step by step procedure it was just like this:
1. I started the Odin 3.07 and connected my device to see is it was detected or not, my surprise the Odin catch it, and shown added and the port number was 18.
2. I just pulled out the USB cable from my laptop and loaded the BL file only to just flash the bootloader file and see what would happen, I was trying it bcz I was totally disappointed with the device i.e. Grand Prime 530H Duos. I also noticed that my device was not stable even with that black screen it used to restart after almost five minutes in that case. And I knew that in 5 minute I will just be able to flash BL file. The BL file was loaded on the Odin now and I inserted the USB cable again while keeping the vol down button pressed to my laptop when the Odin again found and connected with my device, I didnot take any more time to flash BL file.
3. As soon as i had not flashed all the SW therefore, my device didn't boot properly, and I thought it didn't work but when my device was connected to the computer I just listened the startup tone of the Android 4.4.4. From that moment I knew my device was not dead now so i had to select all four files from the recovery firmware of 4.4.4 and connect the device to odin even there was no sign of download mode, as soon i clicked the Start button i saw many things in the Odin which were good enough to see. after the firmware flashed the device got started.
Sent from my SAMSUNG-SM-G920A using Tapatalk
Click to expand...
Click to collapse
I'm glad I helped you and thanks for your description, other people with the same problem can see it, my English its not good and I was afraid that I didn't help you correctly.

Same problem, but apparently worst!
AwkWeirdo said:
Hello,
I was trying to flash Twrp recovery in my phone using flashify. It said flash successfully and i rebooted. It starting bootlooping. I manually tried by pressing Volume up + Home+Power keys it was still doing bootloop. I tried to goto download mode by pressing Volume Down+ Home+Power keys it still kept bootlooping even USB jig didn't work. I need your valued suggestion about what to do next.
Thanks in Advance.
I have Samsung Galaxy Grand Primr G530H
here is video link youtu.be/B_EtRTH93YE
Click to expand...
Click to collapse
Hello guys! Could you please help me with the same issue? The difference is that Odin doesn't recognize when I plug in my phone! I don't know what else to do. It's a G530H.
Thank you very much!

GorJessSpazzer said:
I'm glad I helped you and thanks for your description, other people with the same problem can see it, my English its not good and I was afraid that I didn't help you correctly.
Click to expand...
Click to collapse
talvigi said:
You are right I did it the same way and it worked for me too. I actually was thinking the phone was quite dead but it wasn't, I just flashed the recovery firmware 4.4.4 Russian and if you ask me for the step by step procedure it was someting like this:
1. I started the Odin 3.07 and connected my device to see if it was detected or not, to my surprise, Odin catch it, and shown added and the port number was 18.
2. I just pulled out the USB cable from my laptop and loaded the BL file only to just flash the bootloader file and see what would happen, I was trying it bcz I was totally disappointed with the device i.e. Grand Prime 530H Duos. I also noticed that my device was not stable even with that black screen it used to restart after almost five minutes in that case. And I knew that in 5 minute I will just be able to flash BL file. The BL file was loaded on the Odin now and I inserted the USB cable again while keeping the vol down + home key pressed, to my laptop when the Odin again found and connected with my device, I didnot take any more time to flash BL file.
3. As soon as i had not flashed all the SW therefore, my device didn't boot properly, and I thought it didn't work but when my device was connected to the computer I just listened the startup tone of the Android 4.4.4. or the device. From that moment I knew my device was not dead now so i pullup the battery, put it again inside to check its status, did this almost thrice, but still the same black screen, yet i heard the startup sound everytime. Now as far as knew the phone is on but showing nothing, I had to select all four files from the recovery firmware of 4.4.4 and connect the device to odin even there was no sign of download mode, as soon i clicked the Start button i saw many things in the Odin bar which were good enough to see. after the firmware flashed the device got started.
Sent from my SAMSUNG-SM-G920A using Tapatalk
Click to expand...
Click to collapse
Sent from my SAMSUNG-SM-G920A using Tapatalk

lucas13garcia said:
Hello guys! Could you please help me with the same issue? The difference is that Odin doesn't recognize when I plug in my phone! I don't know what else to do. It's a G530H.
Thank you very much!
Click to expand...
Click to collapse
Is your USB cable original is it working on other devices? And are you using a USB 2.0 port, that is very much necessary, for Odin and some other hardware/software environment applications. And you also must have Samsung USB drivers installed in your PC, you can also try all this process on some other PCs
Sent from my SAMSUNG-SM-G920A using Tapatalk

talvigi said:
Is your USB cable original is it working on other devices? And are you using a USB 2.0 port, that is very much necessary, for Odin and some other hardware/software environment applications. And you also must have Samsung USB drivers installed in your PC, you can also try all this process on some other PCs
Sent from my SAMSUNG-SM-G920A using Tapatalk
Click to expand...
Click to collapse
Hello!
Yes, that USB works with other phones. And even not being the original one, it was working to transfer files before this issue...
It is a USB 2.0 port, and even when I go to "Device Manage" on Windows, it doesn't show any port with an unknown device or something like that...
Thanks!

Bricked J3 2016 (SM-J320FN)

Hey there, I think my J3 2016 is bricked.
I accidently disabled the "OEM Unlock" in Developer Settings and now I am stuck at the samsung boot screen with a green text in left upper corner saying "Custom Binary blocked by FRP Lock".
I tried to flash the stock firmware with latest version of Odin, but the device isn't showing up. I have windows 7 and I reinstalled several times the drivers. My computer is recognizing it just as an Unknown Device.
Please help me, this is my only phone and at the moment I can't efford another one.

s4ss0 said:
Hey there, I think my J3 2016 is bricked.
I accidently disabled the "OEM Unlock" in Developer Settings and now I am stuck at the samsung boot screen with a green text in left upper corner saying "Custom Binary blocked by FRP Lock".
I tried to flash the stock firmware with latest version of Odin, but the device isn't showing up. I have windows 7 and I reinstalled several times the drivers. My computer is recognizing it just as an Unknown Device.
Please help me, this is my only phone and at the moment I can't efford another one.
Click to expand...
Click to collapse
It can be recovered (I've done that myself). Install Kies and smart switch for the drivers, reboot PC, Open Odin, put the stock firmware (preferably from sammobile) in the AP section, in options turn off auto-reboot, start phone in download mode (volume down, home button and power button together) and connect it,flash the firmware. When it's done reboot using vol up, down, home and power together until it turns on then switch on normally.
That's what worked for me, step by step.

Wulfie217 said:
It can be recovered (I've done that myself). Install Kies and smart switch for the drivers, reboot PC, Open Odin, put the stock firmware (preferably from sammobile) in the AP section, in options turn off auto-reboot, start phone in download mode (volume down, home button and power button together) and connect it,flash the firmware. When it's done reboot using vol up, down, home and power together until it turns on then switch on normally.
That's what worked for me, step by step.
Click to expand...
Click to collapse
The problem is that the phone isn't even showing in Device Manager. Installing and reinstalling drivers isn't useful.

s4ss0 said:
The problem is that the phone isn't even showing in Device Manager. Installing and reinstalling drivers isn't useful.
Click to expand...
Click to collapse
Hmm, I occasionally have issues if I use the wrong cable, have you tried changing that over?
The drivers should have sorted it out and made the phone visible really. I seem to remember that mine doesn't pop up in device manager if its in download mode (though that may be me remembering it wrong).

Wulfie217 said:
Hmm, I occasionally have issues if I use the wrong cable, have you tried changing that over?
The drivers should have sorted it out and made the phone visible really. I seem to remember that mine doesn't pop up in device manager if its in download mode (though that may be me remembering it wrong).
Click to expand...
Click to collapse
I have 6 cables, I've tried them all, not a single one works.

s4ss0 said:
I have 6 cables, I've tried them all, not a single one works.
Click to expand...
Click to collapse
Update; sometimes, if i connect the cable, the phone gets phisically found, but it isn't found like a device, just like "Unknown device". Can I do something?

s4ss0 said:
Update; sometimes, if i connect the cable, the phone gets phisically found, but it isn't found like a device, just like "Unknown device". Can I do something?
Click to expand...
Click to collapse
If no cables are working at all then I'm out of ideas sorry.
Ignoring Windows is a good bet, in download mode it often doesn't show up, focus more on whether or not you can see it in Odin, trying different versions of Odin can't hurt either I suppose.

Wulfie217 said:
If no cables are working at all then I'm out of ideas sorry.
Ignoring Windows is a good bet, in download mode it often doesn't show up, focus more on whether or not you can see it in Odin, trying different versions of Odin can't hurt either I suppose.
Click to expand...
Click to collapse
hey there, i just used an older version of odin as you told me and now it works. thanks for the help!

s4ss0 said:
hey there, i just used an older version of odin as you told me and now it works. thanks for the help!
Click to expand...
Click to collapse
No problem s4ss0, I'm glad it ended up being something fairly simple so you could get your phone back.

Connection issues
It is possible to get round the connection issue: Turn off the phone. Turn on the phone in download mode (vol-down, home, power). Connect a Samsung USB cable. Launch ODIN on your PC. Wait a few moments and you should see green text on top left of phone 'ODIN MODE'. Your phone is ready to take downloads.