Hi guys, I have a Samsung Galaxy S4 from Canada, specifically Rogers. The phone is currently on the CM11 Nightly ROM. (I can check specifically which nightly, my phone is just backing up at the moment so I can't see!)
I have this problem, which is, when the phone automatically locks or I myself lock it, the radio signal completely drops. Sometimes the signal will come back, but to get it back for sure is to turn the phone on airplane mode then off again. It is annoying because when the phone is locked for a while, it will receive signal at some point. During that time I'll get a call and it'll ring but once the screen turns on the signal will drop, also dropping the call. I have a slight understanding that it could be a problem with the phone's radio firmware?
Now that you guys have an understanding about my problem, this is what I am hoping to accomplish. I want to update the phones ROM, as it is probably old, along with the proper fix to the phone's radio firmware. How do i go about doing this? The kind of ROM that I want is something in between stable version and nightly (not nightly as I think nightly was the one that caused my radio problem), I think that's SNAPSHOT M12? Please correct me if I am wrong. I would rather not lose any of my data but if I have to then I will but please do guide me because I am scared to lose any of my data.
Thank you guys for reading my long post, I hope my English and grammar is fine! I look forward to hearing from you guys!
The current version of Cyanogenmod is 12.1 (Android 5.1.1). The two release channels for 12.1 are nightlies and snapshots. As of yet there has been no CM12.1 snapshot I'm aware of, meaning all CM12.1 ROMs are nightlies.
You haven't said what version of the stock ROM you had before moving to CM11, but if the radio is too old, you'll want to update it. You'll need Odin and either the modem file, or a complete ROM, which you can download from here. If you choose to install the stock ROM, be aware that you will have to root your device again, using CF-Autoroot. Flashing the stock ROM or modem won't wipe your data unless you tell Odin to partition the S4, so you don't want to do that. What you do want to do before you attempt to do anything is make a nandroid backup as well as move any important files off the internal storage. While you won't need to wipe the S4 prior to installing the new stock ROM or the modem, you will need to do so when installing the new version of Cyanogenmod.
P. S. In the future, you want to direct your questions to the AT&T Galaxy S4 forums as this is the International S4 forum, which doesn't cover North American S4 devices. Your question however is general enough that we should still be able to help you.
Thanks for the reply!
Strephon Alkhalikoi said:
You haven't said what version of the stock ROM you had before moving to CM11
Click to expand...
Click to collapse
I don't know how to answer this, It's been quite a long time since I moved to CM11. Basically what I did was, when I bought the phone I went home and installed CM11 on it, haha.
Strephon Alkhalikoi said:
You'll need Odin and either the modem file, or a complete ROM, which you can download from here. If you choose to install the stock ROM, be aware that you will have to root your device again, using CF-Autoroot. Flashing the stock ROM or modem won't wipe your data unless you tell Odin to partition the S4, so you don't want to do that. What you do want to do before you attempt to do anything is make a nandroid backup as well as move any important files off the internal storage. While you won't need to wipe the S4 prior to installing the new stock ROM or the modem, you will need to do so when installing the new version of Cyanogenmod.
Click to expand...
Click to collapse
I am quite confused, sorry. What I'm doing right now is I'm downloading the newest radio firmware from the link you have given me. After that I'm going to follow the instructions of:
Extract (unzip) the firmware file
Download Odin v3.10.6
Extract Odin ZIP file
Open Odin v.3.10.6
Reboot Phone in Download Mode (press and hold Home + Power + Volume Down buttons)
Connect phone and wait until you get a blue sign in Odin
Add the firmware file to AP / PDA
Make sure re-partition is NOT ticked
Click the start button, sit back and wait few minutes
That will fix my radio problems?
Now to update my ROM. This is where I am mostly confused. In your opinion, should I stick with CM11 Nightly? Can I somehow go from nightly to a more stable version like cm11 snapshot m12? Should I update to CM12? Will my phone keep up with the CM12 ROM?
Strephon Alkhalikoi said:
P. S. In the future, you want to direct your questions to the AT&T Galaxy S4 forums as this is the International S4 forum, which doesn't cover North American S4 devices. Your question however is general enough that we should still be able to help you.
Click to expand...
Click to collapse
Sorry I will keep that in mind! Mind you, I carefully chose this and looked at all my other options. I didn't see the AT&T forum to fit because AT&T is in the United States and my carrier is in Canada, I just didn't want to have problems with anything else
Guys, I think i screwed up.... So when i downloaded that firmware from Sammobile. I flashed it with ODIN and made sure re-partition was not checked. Everything looked fine and when my phone rebooted (its still rebooting at the moment) the welcome screen was the default "samsung" splash screen, not the Cyanogen Mod . I thought this method was only going to flash the phone's modem, not the ROM too
EDIT:
No....my worst nightmare came true .........NO!!!!
So my phone finished rebooting and its just a black screen. All I can see is the status bar at the top right that displays the WiFi signal and the Phone's network signal and the battery. Okay so I figured something out. When the phone is locked and I press the Home button, Battery Doctor's charging wallscreen shows up, meaning my device wasn't wiped ? When I tried to unlock from Battery Doctor's charging screen, it would just show the black screen with just the status bar .... PLEASE HELP ME !!!
It flashes a complete ROM, which is part of the reason I mentioned making a backup. Now you'll need to root your S4 again, as I mentioned, install a custom recovery, and then you can install Cyanogenmod (12.1 recommended). By flashing the complete ROM it also ensures you have a clean slate from which to move forward. Now all the firmware pieces "match" and you avoid any odd effects by having a mismatched bootloader and baseband.
Strephon Alkhalikoi said:
It flashes a complete ROM, which is part of the reason I mentioned making a backup. Now you'll need to root your S4 again, as I mentioned, install a custom recovery, and then you can install Cyanogenmod (12.1 recommended). By flashing the complete ROM it also ensures you have a clean slate from which to move forward. Now all the firmware pieces "match" and you avoid any odd effects by having a mismatched bootloader and baseband.
Click to expand...
Click to collapse
D'awww Well I guess a clean slate isn't so bad. I backed up my text messsages and my photo's should be backed up onto the google drive anyways. I don't know if you saw my edited post but the UI is not loading. Its just showing the status bar at the top right (signal, wifi signal, battery).
Thanks.
If you're going to install CM12.1 I wouldn't worry about Touchwiz not starting. Just go ahead and prep the phone for Cyanogenmod, as the most important parts - baseband and bootloader - are apparently working properly.
EDIT: ROM installs don't wipe data when done through Odin unless you tell Odin to partition the device. Thus you'd need a factory reset to ensure Touchwiz works. But where you're going to put Cyanogenmod on, don't worry about Touchwiz.
Strephon Alkhalikoi said:
If you're going to install CM12.1 I wouldn't worry about Touchwiz not starting. Just go ahead and prep the phone for Cyanogenmod, as the most important parts - baseband and bootloader - are apparently working properly.
Click to expand...
Click to collapse
The problem is, I can't. There's nothing there on the phone. Its just a black screen. Unless, thats what you meant.
I tried searching for a CM 12.1 Canadian version and I found this thread. http://forum.cyanogenmod.org/topic/104233-jfltesgh-i337m/
apparently theres no canadian version of the CM 12.1
what should I do ?
Use the Optimized CM12.1 here in I9505 Original Android Development. It's supposed to work with all Qualcomm S4s except the Value Edition S4.
Oh, and you don't need CF-Autoroot. Simply install the recovery using Odin, then install Cyanogenmod. Wipe data and cache, then reboot. Everything should be back to normal about ten minutes after rebooting, as the ART compiler compiles the apps.
Strephon Alkhalikoi said:
Use the Optimized CM12.1 here in I9505 Original Android Development. It's supposed to work with all Qualcomm S4s except the Value Edition S4.
Oh, and you don't need CF-Autoroot. Simply install the recovery using Odin, then install Cyanogenmod. Wipe data and cache, then reboot. Everything should be back to normal about ten minutes after rebooting, as the ART compiler compiles the apps.
Click to expand...
Click to collapse
Thanks for the replies! I'm sorry if im asking for too much but could you please confirm that this is the right one? link
So, I don't need to root? how can i verify that my phone is still rooted? If my phone is still rooted, I download Canadian Galaxy S4 SGH-i337M (Bell, Rogers, Telus) – CWM Recovery v6.0.4.4
Then flash that with Odin ?
edit: I think I know why this failed miserably....On Odin V3.10.6 I clicked "AP" for some reason, when I was flashing the firmware. Could that be the problem? If so, is there a fix ? i can't access my phones SD card .
Right link, but Clockworkmod is not a good choice for a recovery to flash through Odin. Use TWRP instead as Clockworkmod is no longer updated.
Cyanogenmod is pre-rooted, though until you open the developer options in settings you can't access it. That's why you don't need to root beforehand. There is no harm however if you choose to root anyway before installing.
Clicking Odin like that shouldn't do anything. But where you've encountered problems, read the instructions here to wipe the storage. Then install the stock ROM again through Odin to see if that resolves the problem.
i just installed cm-12.1-20150625-NIGHTLY-jfltexx on my s4 with cm-12.1-20150623-NIGHTLY-jfltexx but there is a problem with the phone functions. It can't make any call. .it do not find my sim card!! Same thing with cm-12.1-20150624-NIGHTLY . The last one that works is 20150623 . Is there anyone that can confirm my problem?
Strephon Alkhalikoi said:
Right link, but Clockworkmod is not a good choice for a recovery to flash through Odin. Use TWRP instead as Clockworkmod is no longer updated.
Cyanogenmod is pre-rooted, though until you open the developer options in settings you can't access it. That's why you don't need to root beforehand. There is no harm however if you choose to root anyway before installing.
Clicking Odin like that shouldn't do anything. But where you've encountered problems, read the instructions here to wipe the storage. Then install the stock ROM again through Odin to see if that resolves the problem.
Click to expand...
Click to collapse
I am following this:
Code:
TWRP Recovery v2.8.7.0 is suggested for installation
First time or clean install:
Download the ROM from the link above
Download GApps package for Lollipop 5.1
Put the zip files on your SDCard
Reboot in Recovery
Wipe Data / Factory Reset
Optional: convert to F2FS
Select "Install zip from SDCard"
Choose ROM's zip file
Choose GApps zip file
Reboot system
Unfortunately, I am stuck though. I can't put the zip files in my phone because my phone is semi-bricked. I can't access my SD card. I don't have another device that I could plug my SD card into, and I don't have an SD card reader either!
edit: sorry im really like uneasy right now and im thinking that I don't want to lose all my data, so i'm exploring a bit. I booted up CWM because I had a backup made from there. I saw the backup, but when I tried to restore it, it said "MD5 Mismatch" is there ANY way I could get that backup of mine to restore? I would have a peace of mind and then we can restart this process from there.
flipboi15 said:
I am following this:
Code:
TWRP Recovery v2.8.7.0 is suggested for installation
First time or clean install:
Download the ROM from the link above
Download GApps package for Lollipop 5.1
Put the zip files on your SDCard
Reboot in Recovery
Wipe Data / Factory Reset
Optional: convert to F2FS
Select "Install zip from SDCard"
Choose ROM's zip file
Choose GApps zip file
Reboot system
Unfortunately, I am stuck though. I can't put the zip files in my phone because my phone is semi-bricked. I can't access my SD card. I don't have another device that I could plug my SD card into, and I don't have an SD card reader either!
edit: sorry im really like uneasy right now and im thinking that I don't want to lose all my data, so i'm exploring a bit. I booted up CWM because I had a backup made from there. I saw the backup, but when I tried to restore it, it said "MD5 Mismatch" is there ANY way I could get that backup of mine to restore? I would have a peace of mind and then we can restart this process from there.
Click to expand...
Click to collapse
I assume your model is i337M. Check it in download mode. If that's the case, then follow this.
1. Flash this:
http://forum.xda-developers.com/galaxy-s4-att/general/sgh-i337m-canadian-stock-official-t3082758
2. Flash TWRP
3. Flash the rom you want.
That's all. You are making it to difficult.
Lennyz1988 said:
I assume your model is i337M. Check it in download mode. If that's the case, then follow this.
1. Flash this:
http://forum.xda-developers.com/galaxy-s4-att/general/sgh-i337m-canadian-stock-official-t3082758
2. Flash TWRP
3. Flash the rom you want.
That's all. You are making it to difficult.
Click to expand...
Click to collapse
So step 1 and 2 flash that with Odin? Do I wipe or no? If i decide not to wipe, will i still have my old stuff from my phone back?
I am confused with step 3. How do I flash the ROM? Using ODIN? Or TWRP? If its through TWRP, how do I get the ROM in my SD card?
edit: I flashed the first link and this is my log, it failed
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337MVLUGOC4_I337MOYAGOC4_I337MVLUGOC4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> cache.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
tried a second time, it still failed
I think my phone is bricked. Its stuck on "firmware upgrade encountered an issue. Please select recovery mode in Kies and try again"
latest log im digging myself a deeper hole :
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337MVLUGOC4_I337MOYAGOC4_I337MVLUGOC4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Removed!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Added!!
Flashing CM is easy. It doesn't require root access because this phone has no bootloader lock. Download a custom recovery with TAR file format, install drivers, go to the download mode of your phone, connect your phone to your computer, and use Odin to flash the recovery. Then copy CM zip file to a SD card and flash it in recovery. That's all!?
For recovery I recommend TWRP: teamw.in
If you've installed Kies you should have drivers on your computer. Otherwise install Kies or only drivers if you can find them on Samsung official website.
flipboi15 said:
So step 1 and 2 flash that with Odin? Do I wipe or no? If i decide not to wipe, will i still have my old stuff from my phone back?
I am confused with step 3. How do I flash the ROM? Using ODIN? Or TWRP? If its through TWRP, how do I get the ROM in my SD card?
edit: I flashed the first link and this is my log, it failed
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337MVLUGOC4_I337MOYAGOC4_I337MVLUGOC4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> cache.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
tried a second time, it still failed
I think my phone is bricked. Its stuck on "firmware upgrade encountered an issue. Please select recovery mode in Kies and try again"
latest log im digging myself a deeper hole :
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337MVLUGOC4_I337MOYAGOC4_I337MVLUGOC4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Removed!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Added!!
Click to expand...
Click to collapse
Use a different usb port / different usb cable.
Thanks for all the help guys I really do appreciate it and I can't thank you all enough. I have the stock rom working at the moment. I have TWRP installed and I put the ROM and GAPPS into my SD card. I booted into TWRP recovery and clicked on install then i chose the ROM zip but, it fails. This is the error attached picture.
flipboi15 said:
Thanks for all the help guys I really do appreciate it and I can't thank you all enough. I have the stock rom working at the moment. I have TWRP installed and I put the ROM and GAPPS into my SD card. I booted into TWRP recovery and clicked on install then i chose the ROM zip but, it fails. This is the error attached picture.
Click to expand...
Click to collapse
Try redownloading the .zip file. Maybe it's corrupt.
So after trying to install the ROM in TWRP and failing. I couldn't load up the phone anymore, it got stuck at the Samsung Logo screen. I am now re-flashing I337MVLUGOC4 - 5.0.1 Lollipop.
edit:
So at the moment, my phone is working fine on stock rom. I redownloaded the CM-12.1 optimized. I moved it into my SD card. I need to know if there are certain steps I need to do to get this right. These are the steps I took the first time.
Rebooted into TWRP recovery mode, then clicked install then I navigated to the CM-12.1 ROM zip and swiped to install.
Was I supposed to wipe anything? The only time I wiped(the default wipe in twrp) was after I installed the 5.0.1 Lollipop firmware. By the way, i noticed that my phone's internal memory is almost full, it only has 2GB of 9.69GB left in the internal. I checked it out and all my old files were still there!
Related
i will tell all the information here..i have my samsung gt-i9505 carrier locked to globe telecom here in the philippines..
i tried to factory unlock here http://forum.xda-developers.com/showthread.php?t=2282683 but i have no luck on it..i have change my baseband several time via odin but still i pin request always shows after i reboot..i have android version 4.2.2, stock firmware DXUBMF8.
so i stopped from there..i moved on to try to root my s4,before having this phone i had owned a s4 factory unlock and i have had rooted it but i already forgot how to do it again..so started anew by looking again at forum threads,i have tried omega custom rom but if i goes to recovery mode my screen only shows the following options: reboot system now, apply update from ADB, apply update from external storage, wipe data/factory reset, wipe cache partition, apply update cache..my question here was,is this the default recovery mode of s4 now?because i can still recall that my last s4's default recovery menu shows with advance option with wipe dalvik cache etc..and my recovery menu now shows no apply update from internal storage..when i tried flashing the custom rom save on my sd card: apply update>omega*something*.zip..it all well done but after rebooting my phone didn't any stuff from that custom rom nor rooted at all..can you help me solving this?
and lastly this is my main problem now,i searched again the thread and went down to this thread http://forum.xda-developers.com/showthread.php?t=2250824 i downloaded the pre-rooted rom XXUBMF8..flashed it with odin PDA..passed and from then my phone was stocked every time i reboot to samsung logo..
i have tried to flash again on a stocked rom. odin>PHONE>(the stock rom)>start>passed then reboot it still stocked to samsung logo..
sorry this was too long to read but i have to tell what all i have been done resulting to this..can someone help me..i will be very thanful for your help..
can anyone help me with this?i have been searching the forum for hours..i have done flashing through odin with stock rom and pit file but it ended up failed..done factory reset with default recovery mode but nothing happens still stucked on boot logo..
still no luck.. it was almost 24 hours since my phone bricked..can someone kindly help me.
voidjov said:
still no luck.. it was almost 24 hours since my phone bricked..can someone kindly help me.
Click to expand...
Click to collapse
The recovery your talking about is cwm not default s4 recovery you'll find that recovery here
http://forum.xda-developers.com/showthread.php?t=2281367
After its installed try wiping data then cache then going into advanced and wiping dalvik cache
S4 Info
did you try from the stock rom to go to recovery many and wipe to factory default again...
Have you tried to install a recovery like Philz and see if you can access the file system of your GS4.
You'll also find more wiping option
Edit: oh great some1 posted before me.
also try to do it from your official rom
TingTingin said:
The recovery your talking about is cwm not default s4 recovery you'll find that recovery here
http://forum.xda-developers.com/showthread.php?t=2281367
After its installed try wiping data then cache then going into advanced and wiping dalvik cache
S4 Info
Click to expand...
Click to collapse
no it was stock recovery what i have used not cwm i think..thats the problem because i am used to using cwm that's where all my problem started because i used stock recovery instead which i am not so familiar.
daibaron said:
did you try from the stock rom to go to recovery many and wipe to factory default again...
Have you tried to install a recovery like Philz and see if you can access the file system of your GS4.
You'll also find more wiping option
Edit: oh great some1 posted before me.
also try to do it from your official rom
Click to expand...
Click to collapse
i have read philz thread and tried flash the .tar file with PDA odin but an error shows:
odin failed once again after flashing a stock rom, the error was:
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Removed!!
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
no im on a screen shows firmware upgrade encountered an issue. Please select recovery mode in Kies and try again.,
now i cant go even on a stock recovery but i can do download/odin mode..i will not do any further steps from now on,i will wait for your help guys,i don;t want to pay to unbricked my s4,i have to fix it all by myself and your kind help guys..
voidjov said:
no it was stock recovery what i have used not cwm i think..thats the problem because i am used to using cwm that's where all my problem started because i used stock recovery instead which i am not so familiar.
i have read philz thread and tried flash the .tar file with PDA odin but an error shows:
odin failed once again after flashing a stock rom, the error was:
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Removed!!
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
no im on a screen shows firmware upgrade encountered an issue. Please select recovery mode in Kies and try again.,
now i cant go even on a stock recovery but i can do download/odin mode..i will not do any further steps from now on,i will wait for your help guys,i don;t want to pay to unbricked my s4,i have to fix it all by myself and your kind help guys..
Click to expand...
Click to collapse
In the Thread you point out... read AGAIN about PIT
http://forum.xda-developers.com/showthread.php?t=2265477
Download the PIT and follow the exact procedure... it's not like flashing a new firmware so read which boxes you check
Try the PIT file with / without the firmware
check also this thread... in case you have a pit related error.
http://forum.xda-developers.com/showthread.php?t=2283919
I'm sure you have all you need to recover your phone.
When you will have recovered your phone, update this thread saying you solved your problem.
check also this thread... in case you have a pit related error.
OH, don't forget to update my thanks counter
Hello,
I saw an answer to this problem in another thread. You have to swipe the phone by starting it with VOLUME UP + HOME + POWER, and then whatever options you have to swipe everything.
Problem SOLVED!!!
hey guys i have solved my greatest problem since i started rooting back on my N7100,my 1st s4 and now my new s4..
thank you for all who helped me,after more than 24hours of reading and waiting for you replies and doing some intervention on my s4,i have recover it..i will post here how i did it for reference for others who might encounter this problem same as mine:
first of all i have noticed this just after successfully revived my phone, you have to WIPE THE DATA/FACTORY REFORMAT via recovery mode before and after doing any firmware update,then i just removed my battery may be a minute and put it back again every time i do flashing..
i used odin version 1.85 not version 3.04..i first chose the pit file and flash it.(when i tried flashing the pit and stock rom together it always ended up to fail)..so i decided to chose to flash the pit file only using odin v1.85(it automatically ticked the "repartition option on this odin version" then it passed..after that as i have said remove battery,wipe data,then i removed again the battery,then put it back and do download/odin mode on my phone,then i flashed stock rom from www.sammoble.com, i searched for globe carrier since my phone was locked on that carrier, then after 2-3minutes(be patient and don't do anything while waiting) my phone backed to life!!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMF8_I9505OLBBMF8_I9505DXUBMF8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> NON-HLOS.bin
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
for those guys who helped me, i have pressed the thanks button for you guys 100x(i hope i can do that)..but truly i am very much thankful for you guys..i do not have to go to service provider technician or any cellphone repair stall just to repair my phone and pay,i have revived it with your help..THANK YOU!!!
i must add i would like to ask what is the best way to root my phone, i have read chainfire autoroot, is the best way to root my phone?as i can remember it is the same way i have rooted my first s4 two months ago because i saw my old folder here on my pc with that application..and best custom rom?
and the best way to factory unlock my phone, the working firmware..
you can post the link so i can read and do it myself..
Hi guys, long time lurker here anyway i've always flashed my S4 with odin and not a single problem always flashed STOCK firmwares
but today i recently discovered a new firmware on the list for the GT-I9500 Exynos Octa (version) - this firmware to be in fact I9500ZNUCMI1
but now its bombed... it hanged and hanged at booting for 20 min then it shut it self off turned it back on 'the firmware encounter a problem' message popped up... i cannot go into recovery mode AT ALL (just download mode) so i thought i will flash my previous stock firmware known as I9500XXUBMG9 but now i cant even do that..... odin just gives me a god damn fail - FOR THE LOVE OF ANDROID HELP ME
- Kies is not running in the background
- USB connections are fine
- Cables are fine
So do i have to fear this is the end ? lol i cannot believe this happened to me on a STOCK firmware.... (lucky for me... all my stuff is backed up on sd)
Any help would be greatly appreciated
lethcore said:
Hi guys, long time lurker here anyway i've always flashed my S4 with odin and not a single problem always flashed STOCK firmwares
but today i recently discovered a new firmware on the list for the GT-I9500 Exynos Octa (version) - this firmware to be in fact I9500ZNUCMI1
but now its bombed... it hanged and hanged at booting for 20 min then it shut it self off turned it back on 'the firmware encounter a problem' message popped up... i cannot go into recovery mode AT ALL (just download mode) so i thought i will flash my previous stock firmware known as I9500XXUBMG9 but now i cant even do that..... odin just gives me a god damn fail - FOR THE LOVE OF ANDROID HELP ME
- Kies is not running in the background
- USB connections are fine
- Cables are fine
So do i have to fear this is the end ? lol i cannot believe this happened to me on a STOCK firmware.... (lucky for me... all my stuff is backed up on sd)
Any help would be greatly appreciated
Click to expand...
Click to collapse
If you can get into Download mode, all hope is not lost. Uninstall and resinstall drivers, Odin, etc. reboot.
Odin back to stock, immediately boot into stock recovery, wipe data, reboot.
Done.
donalgodon said:
If you can get into Download mode, all hope is not lost. Uninstall and resinstall drivers, Odin, etc. reboot.
Odin back to stock, immediately boot into stock recovery, wipe data, reboot.
Done.
Click to expand...
Click to collapse
Thx for reply
Still says FAIL when i try to flash I9500XXUBMG9 what am i doing wrong ?
rebooted laptop twice plug in S4 via usb says unknown device when in download mode but odin reconise it flash it and nothing happens on the screen then i get the big fat RED FAIL ............... AHHH
lethcore said:
Thx for reply
Still says FAIL when i try to flash I9500XXUBMG9 what am i doing wrong ?
rebooted laptop twice plug in S4 via usb says unknown device when in download mode but odin reconise it flash it and nothing happens on the screen then i get the big fat RED FAIL ............... AHHH
Click to expand...
Click to collapse
The good news is that Download mode is still working. AS long as that's the case, you can get it back. Just keep trying. Switch PCs, switch cables, switch ports, re download a different stock ROM, etc. do whatever it takes to try every variable you can think of.
Eventually, you'll find what's causing it and the ROM will flash successfully. When that happens, get immediately into recovery and wipe data.
(Remove the battery after it flashes, but it back in and hold vol-up+home+power.)
After the data wipe....
Reboot.
Like I said, Download mode means you can find a way to flash, but working with Odin to resolve these issues can sometimes be a PITA. I've had the same thing myself before. Just don't give up. Try to stay calm, and work your way through it. You'll get it eventually.
Edit: Just noticed that you flashed a CHINA firmware. (Why? ) You may be facing this issue because (I think) they use a different pit. There's a thread devoted to resurrecting the device with pit. Maybe check it out.
lethcore said:
Thx for reply
Still says FAIL when i try to flash I9500XXUBMG9 what am i doing wrong ?
rebooted laptop twice plug in S4 via usb says unknown device when in download mode but odin reconise it flash it and nothing happens on the screen then i get the big fat RED FAIL ............... AHHH
Click to expand...
Click to collapse
dont flash China or Hong kong firmwares.
please post odin progression
samersh72 said:
dont flash China or Hong kong firmwares.
please post odin progression
Click to expand...
Click to collapse
Nothing to post just says 'completed' but its failed.... i'll remember this next time stay away from china/hong kong firmwares...
im still tyring now and will let you guys/girls know how it pans out! wish me luck!
lethcore said:
Nothing to post just says 'completed' but its failed.... i'll remember this next time stay away from china/hong kong firmwares...
im still tyring now and will let you guys/girls know how it pans out! wish me luck!
Click to expand...
Click to collapse
INFO HERE
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9500XXUBMG9_I9500OJVBMG9_I9500XXUBMG9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> param.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> persdata.img
<ID:0/005> system.img
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
lethcore said:
INFO HERE
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9500XXUBMG9_I9500OJVBMG9_I9500XXUBMG9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> param.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> persdata.img
<ID:0/005> system.img
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
recovery is flashed, try to boot into it and make the wipe then re-flash stock, re-wipe.
if not, flash a custom recovery, format system, cache, re-flash stock, re-wipe
@donalgodon
Why ? well i got the I9500 in hong kong (im actually based in china now) (not Chinese though) thought i'll see some nice changes? but seems i fK'ed the phone.... pit? i haven't a clue man pit number? think i've KILLED HER... lol (i never knew the dangers of Chinese firmware) - wont be going down that route again.
@samersh72
Are you sure? i cannot get into 'recover' mode... the phone just hands at 'Firmware upgrade encounted an issue please select kies & try again
i canm only enter download mode.... when i try to enter recover mode it just flashes at the firmware message.
lethcore said:
@samersh72
Are you sure? i cannot get into 'recover' mode... the phone just hands at 'Firmware upgrade encounted an issue please select kies & try again
i canm only enter download mode.... when i try to enter recover mode it just flashes at the firmware message.
Click to expand...
Click to collapse
flash custom recovery,
if not see my signature for flashing right pit with the firmware
samersh72 said:
flash custom recovery,
if not see my signature for flashing right pit with the firmware
Click to expand...
Click to collapse
Well i just grabbed a I9500 pit file and have my stock firmware just add these 2 to odin and click start? that simple or ??
lethcore said:
Well i just grabbed a I9500 pit file and have my stock firmware just add these 2 to odin and click start? that simple or ??
Click to expand...
Click to collapse
yes, make sure that you are using the right pit, put it in "pit" window in odin, and the firmware in "pda", make sure "re-partition" is ticked, start.
samersh72 said:
yes, make sure that you are using the right pit, put it in "pit" window in odin, and the firmware in "pda", make sure "re-partition" is ticked, start.
Click to expand...
Click to collapse
Well you be happy to know
installed the previous firmware and that pit file for I9500 from your sig and everything seems well... booted correctly nothing lost all seems good to early to tell but will keep you informed !
THANK YOU!!!
Hello everyone,
I'm trying to flash a stock rom on a Verizon GS5. I say trying because so far it hasn't been working, unless I'm doing something wrong, which I think I am. When I got the phone, it had a Sprint rom flashed to the GS5. The original Verizon IMEI under the battery is clean and verified good with Verizon. There is nothing physically or cosmetically wrong with the phone, it powers on sometimes and randomly restarts. When it does turn on, the Sprint Spark logo comes up, the phone boots up normally and then randomly shuts off, taking a long time to be able to power back on. The only way that it says on is by putting it on Download Mode.
When in download mode, it shows as a G900P,
As far as my understanding goes, shouldn't it be a G900V?
I attempted to flash a stock Verizon rom I downloaded and tried to flash it with Odin 3.04 but it fails each and every time. I have installed the Samsung drivers that I got from the website, I restarted the computer, I restarted the phone but Odin give me a fail error.
Then I tried a newer version of Odin 4.43 but I'm not sure I'm using that one correctly but it's not working for me either.
I left the phone in Download Mode and it has been on for about 30 mins (the longest so far without it restarting on me).
Is there something that I'm missing here? Something else I could try to fix this?
Any ideas? Suggestions?
Any help would be greatly appreciated!!
..
-> It's a Verizon Galaxy S5 Phone I got from eBay
-> It's flashed with the Sprint rom version of the GS5
-> The phone restarts on and off, randomly, unless it is in Download Mode
-> I want to flash it back to the original Verizon GS5 rom.
-> I attempted to flash the phone with Odin 3.09 and rom SM-G900V_VZW_1_20140331185350
-> I get an error message when using Odin 3.09, it FAILS
-> The progress bar in the GS5 phone advances a small amount but that's it.
-> I attempted to use Odin 4.43 with the same rom file but that also fails and I get an error message.
-> I researched on Google before signing up and asking for help.
-> I have read many Threads and Posts on several Forums, and I have also tried many tutorials without any luck.
-> I researched how to use Odin, there is lot's of pictures, easy explanations but that's not it.
-> I found a GS5 stock rom, file name mentioned above.
-> Samsung drivers are installed, phone is recognized by Odin.
1.) Am I using the correct rom?
2.) Which version of Odin should I use?
..
SewerDweller said:
Hello everyone,
Any ideas? Suggestions?
Any help would be greatly appreciated!!
Click to expand...
Click to collapse
Download this version of Odin and extract the folder in the zip.
Make sure you have downloaded the correct firmware, extract the MD5 / tar file from inside the firmware.zip file you downloaded and put it in the Odin 3.07 folder
Start Odin.exe, put your phone in download mode and connect to your PC, if you have Kies installed make sure it is not running, Odin and Kies don't mix.
Once you have the Blue ID.COM indicated, click on PDA, find the MD5 / .tar file wait for teh file check Odin runs then click Start, wait for Odin to finish and your phone reboots.
Guide for Odin use here it is from the S3 but the use of Odin is the same for the S5
It took me a while to get it to turn on but here's what I got from trying ag4751's suggestions.
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900VVRU1ANI2_G900VVZW1ANI2_G900VVRU1ANI2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
It's the same thing that I was getting before, I'm sorry if I did not explain myself in detail at first.
I have used 2 versions of Odin 3.09 (which I used on my own and got the above message).
3.07 as suggested by ag4751.
I have used 2 different roms and both fail.
->G900V_VZW_1_20140331185350
->G900VVRU1ANI2-20140919141518
@fffft
To answer your question as to what tutorial I followed, I followed ag4751's tutorial/explanation on his reply. It's basic, just like all the other tutorials I googled.
1.) Put the phone in download mode
2.) Open Odin
3.) Select PDA
4.) Wait for the file check
5.) Click start
and then it fails.
That's what @ag4751 suggested, that's what I tried, that's what I tried before, that's what I'm trying now and all that is failing for some reason.
..
..
Hello I was trying to root my G900F that is currently running Lollipop BNL7 with CF-Auto-Root-klte-kltexx-smg900f and Odin 3.09 after enabling USB debug but Failed at the end of the process. Had to restore stock G900FXXU1BNL7 to get phone back working.
Try it two times always fails at the end.
Any other method or have to wait for updated version of CF-Auto?
Does G900FXXU1BNL7 is rootable?
Is there a way to downgrade to 4.4 safely as I try already and end up in nightmare and dont have EFS backup that is why I want to root first.?
Code:
<OSM> Please wait..
<OSM> CF-Auto-Root-klte-kltexx-smg900f.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
egejo said:
Hello I was trying to root my G900F that is currently running Lollipop BNL7
Click to expand...
Click to collapse
You haven't done anything serious. Don't worry. You can only use SuperSU 2.38 or above versions. No other method works for TouchWiz Lollipop so far.
Reactivation lock
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I think you already enable (Reactivation lock) from setting --> security
Just uncheck the option and i hope it will work fine
Thanks for the advice but did not work.
I have try these way so to first load a custom recovery via odin to root and install SUperSu tested with both Philz and TWRP but failed also on Odin at the end of the process of each of them.
Had to put stock BNL7 again to recover the phone from "firmware upgrade issue" screen
Does BNL7 has some locked bootloader security or so I cant mod anything neither root it now...
lingowistico said:
You haven't done anything serious. Don't worry. You can only use SuperSU 2.38 or above versions. No other method works for TouchWiz Lollipop so far.
Click to expand...
Click to collapse
egejo said:
Thanks for the advice but did not work.
I have try these way so to first load a custom recovery via odin to root and install SUperSu tested with both Philz and TWRP but failed also on Odin at the end of the process of each of them.
Had to put stock BNL7 again to recover the phone from "firmware upgrade issue" screen
Does BNL7 has some locked bootloader security or so I cant mod anything neither root it now...
Click to expand...
Click to collapse
Yes some people say that it only works with Fusion TWRP 2.8.2.0. I don't know if it's true because I already flashed it before flashing SuperSU 2.38 beta And of course it worked.
i cant install recovery mode on bnl7 . Tried it whole day and all i get is stock recovery mode.
Help ?
lingowistico said:
Yes some people say that it only works with Fusion TWRP 2.8.2.0. I don't know if it's true because I already flashed it before flashing SuperSU 2.38 beta And of course it worked.
Click to expand...
Click to collapse
Thanks, sorry to be such a noob but downloaded the Fusion TWRP you post got the zip... but how to install if unzipped there is no odin Tar or such flashable file...neither like and apk, sorry lost in here?
Lastly to let you know that now I'm in Stock G900FXXU1ANCE, dowgraded from BLN7 to BLN2, then ANJ1 and then ANCE. On all of them I have been trying to root or put a custom recovery, used CF-Auto-Root-klte-kltexx-smg900f, openrecovery-twrp-2.8.1.0-klte or philz_touch_6.57.8-klte with same results always Failing Odin at the end of process... The thing I notice is that always it shown on the dowload mode screen
"QUALCOMM SECURE BOOT: ENABLED (CSB)"
Even after downgrade, could these be the issue?
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.57.8-klte.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Made a little progress here,
As I'm now on G900FXXU1ANCE I used towelroot and finally gain root access it Work installed SuperSu from Gplay and then finally made an EFS backup with samsung tool...
But still dont know why it does not work all other methods and ODIN rooting and cant have a custom recovery neither...But for now I feal a little safer having my EFS on Dropbox to be sure....
Will keep playing trying to get a working custom recovery so to flash customs roms later...But looks like I will have to wait for updates now...
egejo said:
Made a little progress here,
As I'm now on G900FXXU1ANCE I used towelroot and finally gain root access it Work installed SuperSu from Gplay and then finally made an EFS backup with samsung tool...
But still dont know why it does not work all other methods and ODIN rooting and cant have a custom recovery neither...But for now I feal a little safer having my EFS on Dropbox to be sure....
Will keep playing trying to get a working custom recovery so to flash customs roms later...But looks like I will have to wait for updates now...
Click to expand...
Click to collapse
had the same problem as you use this twrp it worked perfect in the end make you scroll down to where it says THE GOODS TWRP ODIN its near the bottom of first post in this link http://forum.xda-developers.com/showthread.php?t=2697762
pnr2020 said:
had the same problem as you use this twrp it worked perfect in the end make you scroll down to where it says THE GOODS TWRP ODIN its near the bottom of first post in this link http://forum.xda-developers.com/showthread.php?t=2697762
Click to expand...
Click to collapse
Thanks but tested an did not work Odin Fails flashing it.
I can only flash stock roms and root on those old enough for towelroot...
I'm starting to think these brand new S5 SM-G900F is starting to come with locked bootloader....
Is there a way to verify these...?
egejo said:
Thanks, sorry to be such a noob but downloaded the Fusion TWRP you post got the zip... but how to install if unzipped there is no odin Tar or such flashable file...neither like and apk, sorry lost in here?
Click to expand...
Click to collapse
This is the story that I heard and followed, after which I got root on bln2:
You can only get root on Samsung Lollipop with SuperSU v2.38 and above, but the only 100% sure way to flash SuperSU v2.38+ is by flashing it in Fusion TWRP 2.8.2.0.
So you do it like this:
1 Flash rom in odin
2 Flash custom recovery in Odin (CWM/TWRP doesn't matter)
3 Now boot custom recovery and flash the Fusion TWRP 2.8.2.0 zip file
4 Reboot recovery
5 Flash SuperSU v2.38+ zip
6 Enjoy root
lingowistico said:
This is the story that I heard and followed, after which I got root on bln2:
You can only get root on Samsung Lollipop with SuperSU v2.38 and above, but the only 100% sure way to flash SuperSU v2.38+ is by flashing it in Fusion TWRP 2.8.2.0.
So you do it like this:
1 Flash rom in odin
2 Flash custom recovery in Odin (CWM/TWRP doesn't matter)
3 Now boot custom recovery and flash the Fusion TWRP 2.8.2.0 zip file
4 Reboot recovery
5 Flash SuperSU v2.38+ zip
6 Enjoy root
Click to expand...
Click to collapse
I cant flash any custom recovery at all it always fails and softbricks the phone... Looks like these G900F is now bootloader Locked...
If so samsung is now selling them from factory locked not just ATT versions...
egejo said:
Thanks but tested an did not work Odin Fails flashing it.
I can only flash stock roms and root on those old enough for towelroot...
I'm starting to think these brand new S5 SM-G900F is starting to come with locked bootloader....
Is there a way to verify these...?
Click to expand...
Click to collapse
dont know to be honest mine only 2 weeks old from uk was on BTU but now on polish version
egejo said:
Looks like these G900F is now bootloader Locked...
Click to expand...
Click to collapse
I don't think so, everything works fine for me..
i also cant install recovery but i dont get soft bricks , just normal stock recovery mode all over.
"qualcomm secure boot: Enabled (csb)
hello everyone
if you got error in odin when flash any custom recovery just deactivate reactivation lock from setting>security.
** DISCLAIMER: I AM NOT A DEVELOPER. I DO THIS AS A HOBBY AND SHARE MY FINDINGS IN CASE SOMEONE ELSE FINDS THEM USEFUL. **
** THIS WORKED ON MY DEVICE BUT IT MAY NOT WORK ON YOURS. APPLY AT YOUR OWN RISK **
Background
AS of March 27, 2015, the most recent firmware for Note Pro 12.2 international version is the Russian P905XXUAOB1 (with CSC905SERAOB1 and Modem905XXUANA7), Since it doesn't seem that any country is in a hurry to push a lollipop update into this device, I made these files to update the tablet to the latest available firmware. The procedure is designed to achieve two thing: 1- by leaving the bootloader untouched, it is reversible to your current version, if you have the firmware corresponding to your current version at your disposal, 2- it gives you root.
This procedure should not in theory wipe your data but DO MAKE A BACKUP, in case.
And no, it doesn't trip the knox.
Upgrade Procedure
All files that you need are available at the link further down. The are zipped but you should unzip them before using them.
1- Backup everything you have on your tablet
2- Reboot the tablet to the "Download Mode" (by pressing down vol + home key when the device is rebooting, right before you see the first splash logo, then push Up Vol to continue).
3- Run PC Odin v3.09 and load these files (remember to unzip the files after downloading) :
BL: leave empty
AP: AP.tar.md5
CP: CP.tar.md5
CSC: CSC.tar.md5
Leave everything else unchanged and Start.
4- Let the tablet reboot. It will first go to recovery to complete the upgrade and then reboots and initializes your apps.
Note 1: This process should not erase your data but I suggest you do a factory reset yourself (provided you have saved you data somewhere)
Note 2: After the upgrade is complete, the tablet may run slow and get hot for about 20 min because all the apps are trying to get set up and catalog your system. However, if after 30 minutes is is still slow and hot, first try to wipe the data for Google Plus App. If that doesn't work you may want to disable Google Plus, or as a last resort do a factory reset.
Note 3: If you end up doing a factory reset, the tablet will start up in Russian. You can change the language to English at the very first step of the initial set up. After that, go to settings and change the keyboard and input language to English. Then everything will be OK.
Note 4: If you try this out and don't like it, download your old firmware (must match or be newer than what you had before) and flash your tablet back to how it was (you have to do a factory reset after the downgrading).
Root Procedure
If you need to root the tablet, do the following after you finish the upgrade procedure:
1- Install towelroot v3 on your tablet, but don't run it. The app is inside a zip file at the download site and you should unzip it with the password 12345
This is done because some systems flag this app as a virus when it clearly is not. There are two versions there in the zip file. Either one should work just fine.
2- Install SuperSU, but don't run it.
3- Reboot to download mode.
4- Run PC Odin and load ANC3_Kernel.tar.md5 in AP field and start.
5- Let the system reboot. You may get some force closings after the reboot but ignore them.
6- Run the towelroot app and make it rain!
7- Reboot to download mode.
8- Run PC Odin and load AOB1_Kernel.tar.md5 in AP field and start.
9- Let the system reboot.
10- Run the SuperSU app and let it update the binaries the "normal" way.
11- Allow it to disable knox for you.
12- If SuperSU freezes up for more than 5 minutes reboot your tablet and run it again. Everything will be fine.
13- Your tablet is rooted now.
Download Link
https://mega.co.nz/#F!491wSaQa!wxjErs3ZamrmEPKjYVi50A
Hi
My p905 is on p905xxuanh3. Is it ok to use your method? Tnx
vvkuz said:
Hi
My p905 is on p905xxuanh3. Is it ok to use your method? Tnx
Click to expand...
Click to collapse
Yes. Make sure a matching nh3 firmware is available from sammobile.com if you think you may want to go back to your existing rom at some point.
successfully updated & rooted a p905 with your instructions,
thanks for your help.
Any idea if I can flash this rom into a P905M? Thanks in advance
andrew.mackew said:
Any idea if I can flash this rom into a P905M? Thanks in advance
Click to expand...
Click to collapse
No, because 905M has different cellular and LTE bands and the modem is different. If you still feel adventurous and want to try it, exclude the CP tar file when you are flashing. Make sure you have your current firmware available to restore in case you soft-brick your tablet.
najoor said:
No, because 905M has different cellular and LTE bands and the modem is different. If you still feel adventurous and want to try it, exclude the CP tar file when you are flashing. Make sure you have your current firmware available to restore in case you soft-brick your tablet.
Click to expand...
Click to collapse
Thanks a lot for your reply.
I really wish to change, I mean, since Samsung stuck us on 4.2.2 so far.. I just wish, at least to get a minimal improvement.
If I get to merge things to have a P905 rom working on my P905M it would be an achievement in direction to break the P905M rom prison.
It worked!
Now I have the latest firmware into my P905M.
Thanks!
najoor said:
** DISCLAIMER: I AM NOT A DEVELOPER. I DO THIS AS A HOBBY AND SHARE MY FINDINGS IN CASE SOMEONE ELSE FINDS THEM USEFUL. **
** THIS WORKED ON MY DEVICE BUT IT MAY NOT WORK ON YOURS. APPLY AT YOUR OWN RISK **
Background
AS of March 27, 2015, the most recent firmware for Note Pro 12.2 international version is the Russian P905XXUAOB1 (with CSC905SERAOB1 and Modem905XXUANA7), Since it doesn't seem that any country is in a hurry to push a lollipop update into this device, I made these files to update the tablet to the latest available firmware. The procedure is designed to achieve two thing: 1- by leaving the bootloader untouched, it is reversible to your current version, if you have the firmware corresponding to your current version at your disposal, 2- it gives you root.
This procedure should not in theory wipe your data but DO MAKE A BACKUP, in case.
And no, it doesn't trip the knox.
Upgrade Procedure
All files that you need are available at the link further down. The are zipped but you should unzip them before using them.
1- Backup everything you have on your tablet
2- Reboot the tablet to the "Download Mode" (by pressing down vol + home key when the device is rebooting, right before you see the first splash logo, then push Up Vol to continue).
3- Run PC Odin v3.09 and load these files (remember to unzip the files after downloading) :
BL: leave empty
AP: AP.tar.md5
CP: CP.tar.md5
CSC: CSC.tar.md5
Leave everything else unchanged and Start.
4- Let the tablet reboot. It will first go to recovery to complete the upgrade and then reboots and initializes your apps.
Note 1: This process should not erase your data but I suggest you do a factory reset yourself (provided you have saved you data somewhere)
Note 2: After the upgrade is complete, the tablet may run slow and get hot for about 20 min because all the apps are trying to get set up and catalog your system. However, if after 30 minutes is is still slow and hot, first try to wipe the data for Google Plus App. If that doesn't work you may want to disable Google Plus, or as a last resort do a factory reset.
Note 3: If you end up doing a factory reset, the tablet will start up in Russian. You can change the language to English at the very first step of the initial set up. After that, go to settings and change the keyboard and input language to English. Then everything will be OK.
Note 4: If you try this out and don't like it, download your old firmware (must match or be newer than what you had before) and flash your tablet back to how it was (you have to do a factory reset after the downgrading).
Root Procedure
If you need to root the tablet, do the following after you finish the upgrade procedure:
1- Install towelroot v3 on your tablet, but don't run it. The app is inside a zip file at the download site and you should unzip it with the password 12345
This is done because some systems flag this app as a virus when it clearly is not. There are two versions there in the zip file. Either one should work just fine.
2- Install SuperSU, but don't run it.
3- Reboot to download mode.
4- Run PC Odin and load ANC3_Kernel.tar.md5 in AP field and start.
5- Let the system reboot. You may get some force closings after the reboot but ignore them.
6- Run the towelroot app and make it rain!
7- Reboot to download mode.
8- Run PC Odin and load AOB1_Kernel.tar.md5 in AP field and start.
9- Let the system reboot.
10- Run the SuperSU app and let it update the binaries the "normal" way.
11- Allow it to disable knox for you.
12- If SuperSU freezes up for more than 5 minutes reboot your tablet and run it again. Everything will be fine.
13- Your tablet is rooted now.
Download Link
https://mega.co.nz/#F!491wSaQa!wxjErs3ZamrmEPKjYVi50A
Click to expand...
Click to collapse
Hey mate,
Can you make the same with the latest Lollipop for P905? I wish to flash them into my P905M.. Thanks
andrew.mackew said:
Hey mate,
Can you make the same with the latest Lollipop for P905? I wish to flash them into my P905M.. Thanks
Click to expand...
Click to collapse
Hello from Sao Paulo. Please let us know if you have succeed in installing the italian lollipop on your p905M.
js345 said:
Hello from Sao Paulo. Please let us know if you have succeed in installing the italian lollipop on your p905M.
Click to expand...
Click to collapse
Yep I did. But lost signal.. I am testing a few things..
---------- Post added at 01:13 PM ---------- Previous post was at 01:02 PM ----------
Anyone knows if I can flash a P905 modem into a P905M device?
thanks! successful!:good:
Thank you so much! I've been worried about rooting without tripping knox and this worked perfectly.
One question... If I didn't want to upgrade, could I have just flashed the two firm ware to root?
One of the clearest rooting guides I've used.
Thanks,
Zabben W
zabbenw said:
Thank you so much! I've been worried about rooting without tripping knox and this worked perfectly.
One question... If I didn't want to upgrade, could I have just flashed the two firm ware to root?
One of the clearest rooting guides I've used.
Thanks,
Zabben W
Click to expand...
Click to collapse
No because the second firmware in step 8 should match the existing kernel on your device.
najoor said:
No because the second firmware in step 8 should match the existing kernel on your device.
Click to expand...
Click to collapse
Oh right. That makes sense. Great root guide. If I think about upgrading, I will definitely take a peek at your lollypop one.
Upgrade to P905XXSABQC1_P905BTUABOF1_BTU for SM-P905
Hi All,
Need your help, Tried to upgrade my SM-P905 using ODIN V3.13, using the file downloaded P905XXSABQC1_P905BTUABOF1_BTU. connecting ODIN via USB Cable to the tab. Tried all USB Ports, same issue.
but ODIN unable to move forward with error:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 2365 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> boot.img
<ID:0/004> cache.img.ext4
<ID:0/004> hidden.img.ext4
<ID:0/004> FAIL! (Ext4)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
Please help.
After, and if, aboot and boot are flashed, the rest should get flashed with no issues.
99% of the time this kind failure is either due to a bad USB cable or unnecessary physical movement of the device (which affects the connection) during the flashing process.
So my suggestion is:
1- Make sure you have the latest Samsung drivers installed.
2- Find the best quality cable you have and use that.
3- If the problem persists download another firmware (maybe from another region) and try flashing that.
Hope this helps.
felix_sashi said:
Hi All,
Need your help, Tried to upgrade my SM-P905 using ODIN V3.13, using the file downloaded P905XXSABQC1_P905BTUABOF1_BTU. connecting ODIN via USB Cable to the tab. Tried all USB Ports, same issue.
but ODIN unable to move forward with error:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 2365 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> boot.img
<ID:0/004> cache.img.ext4
<ID:0/004> hidden.img.ext4
<ID:0/004> FAIL! (Ext4)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
Please help.
Click to expand...
Click to collapse