DISCLAIMER
The process of flashing a custom recovery/kernel/firmware may and will trigger your device's Knox Counter. Neither XDA nor I can be held responsible for your actions. Proceed with caution. During this process you will lose all your settings and apps. As long as you follow the instructions, your device's storage, internal and external, won't be touched
Still not compatible with x64 systems! Not compatible with Samsung 5.1.x (sdk22) ROMs!
Hello, Ladies and Gentleman
Many people seem to have a hard time to understand how all of this here on XDA works. I constantly get PM's from users, asking how to do the most basic stuff like flashing a .zip or stock firmware via Odin. Usually, I don't even read them and just hit delete. I know it's not ok to deny people help, so I decided to show you how you can get Xposed working on your TW based stock or custom ROM since it's the most frequently asked question I get.
It's nothing you couldn't do if you'd just....
We're going to use @arter97's customized Xposed Framework as the one made by @darkera13 needs the user to manually modify and replace files which may be too complicated for some.
Preparation
-READ EVERYTHING OVER AND OVER AGAIN.
-A custom recovery System like TWRP or CWM (PhilZ or Stock)
-A deodexed ROM. It's the only way to go. YOU NEED A DEODEXED ROM. If your ROM is not deodexed and you flash the framework, you'll end up in a bootloop. To deodex your existing ROM carefully follow Post #2
Here are a few made by XDA Senior Member @_alexndr
Stock deodexed for SM-N9005 Galaxy Note 3 International Qualcomm.
Stock deodexed for SM-G900F Galaxy S5 International Qualcomm
-And the framework itself from here
[UNOFFICIAL] Xposed for Samsung Lollipop by arter97
-Flash a custom recovery system of your choice. This is listed under preperation on purpose since this guide is about getting Xposed on your TW Lollipop device. A guide on how to get a custom recovery system is most certainly available in your device's forum.
-Store the ROM and the Framework in an easy to find folder, which we're gonna call "folder x". It doesn't matter where you store it (ext. SD or int. SD)
The Fun Part
-Boot into your custom recovery and make a full wipe:
TWRP users: "Wipe>Advanced Wipe> Tick System, Data, Cache, Dalvik Cache> Slide to format.CWM users: "Mounts and Storage> hit Format /System; hit Format /Data; hit Format /Cache.
-Still in recovery system, install, or flash the files we put in folder x;
TWRP users: "Install> Navigate to folder x and choose the ROM file first> Add Zip> now choose the Xposed Framework from folder x> Slide to flash.CWM users: "Install Zip> Choose zip from /sdcard if folder x is on internalt storage or /storage/sdcard1 if folder x is on ext. storage (SD-Card)>choose the ROM file first> -Yes - install ROMXY.zip.Do the same with the Xposed Framework zip file.
-Still in recovery system, reboot device and wait for it to boot. It can take up to 20 minutes. Enjoy Xposed on your Samsung TouchWiz Lollipop ROM.
-Stuck in a bootloop? Try this and repeat the process.
XDA Senior Member @Honzze kindly pointed out to keep following in mind; You have to start JoelDroid Lollipop Batch Deodexer with Admin permissions. Otherwise this error might return "path variable" of Java "is not set".
Deodexing your existing ROM without having to flash an entire ROM
As the title says, with this awesome guide by XDA Senior Member @townsenk you don't have to reflash an entire new ROM to your device. Instead, youll just deodex those parts of your System which need to be modified in order to get Xposed working. You don't necessarily have to perform a full wipe if you do it this way. But if you encounter fc's or end up in a bootloop, you know what to do
Guide for this guide:
Regarding point 1: "...launch a DOS shell..." just means, you need to open the so called "CMD" programm in Windows. To "launch a DOS shell" or CMD from within a folder, you simply have to hold down the shift key and right click in that folder. The context menu will show an entry "open command window here". And that's it! (Windows XP users may have to search the internet for another solution)
For Galaxy S5 and Note 3 users: If ADB returns "device offline" or an empty line after "List of devices attached" make sure your using a USB 2.0 data cable on a USB 2.0 port
townsenk said:
How to DeOdex YOUR (...) Rom.
I would like to note that I appreciate all the work that developers have put forth in creating and maintaining modified Roms. there are some awesome feature rich implementations available. My intentions are not to be critical of any specific Rom or mod. Without the developers we would have nothing.
(...)
This method is very common knowledge I thought I'd just explain it in an easy to understand way.
Here is what you need.
A stock (...) ROOTED configurated phone. Debloat as needed. Set the phone up exactly how you like it with apps and such.
Make sure it's stable. (If you have issues before DeOdexing they will be there afterward!)
Here's the files you may need to make this happen
LBD2.4.zip
7-Zip
Installer template (at end of post)
1> Make sure ADB is working on your computer. USB debugging turned on. Create a folder to store your soon to be download system files and launch a DOS shell from that working folder. Working folder name should NOT contain spaces. With the phone hooked up you should be able to type adb shell and get a prompt.
2> Type these commands
adb pull /system/app app/
adb pull /system/priv-app/ priv-app/
adb pull /system/framework framework/
This will take awhile and you will be left with three folders
Create a new folder named "system" and place these three folders inside.
3> Extract and launch LBD2.4 (This is the DeOdexer and is AWESOME). Point it at your recently created "system" folder and let it do it's thing.
I'll assume this will occur without errors as I have never had any.
4> At this point you can manually apply modded apk's to the system folder but I don't really recommend it. They can be applied afterward using the seperate installer zips.
5> with 7-Zip installed open the provided Installer template. Do not Extract it. Just open it in the 7-Zip file browser using the right click context menu in windows.
Drag-Drop the contents of your system folder into the empty system folder in the 7-Zip browser It should be the three folders previously created but now they are Deodexed. Close the 7-zip file manager and select Yes if it asks you to save.
Note: The provided installer template has been modified to only wipe and replace the three system directories.
6. Copy the created installer to your sdcard and install with recovery. Wipe cache and Dalvik before rebooting.
Go have lunch. You will sit at a boot screen for about 10 minutes. Then another 20 to rebuild caches. Time varies.
7. Your system will now be Deodexed! At this point you can install your mods one at a time, I recommend this so you can test your system between installs to determine if a specific mod is creating problems.
This method has so far removed ALL of my stability issues.
Click to expand...
Click to collapse
Since I no longer own this device, I'm retiring from this thread as of now. Hope I could help you.
Don't know if someone can help me as you stated that you're retired from this thread.
I did every step you do mentioned here (for self deodexing existing rom)
I did everything successfully and deodexed my files with 2.5 deodexer, putted files in the system folder to the 7zip folder and sent to my device and flashed zip, cleaned cache and dalvik and it stuck on booting for about 15 minutes. I know, it takes alot time during rebuildup of cache, but guys, it's 15 minutes! for me, if i cleanup cache and the dalvik/art cache, it just takes 1minute on boot screen to show up the image of each apps cache, but i just sat there with lots of patient for 15 minutes or a bit more and still same, stuck in same crappy booting logo.
I did restore my system files, now i'll try to retry it and send it again. Im suspicious of the zip file being corrupted during trasmitting to Device, however install was a big success so im very sure it wasnt corrupted. I'll do 2nd test and see it again if it's happening again.
If it does, i'll most likely try to figure out other ways to deodex as there is already deodexed roms out there, so they must have done is somehow.
Thanks, hope someone can help me out with this.
P.S: My adb works fine, i got usb drivers for my device, i got usb debug on, i got lots of space on phone, i got TWRP recovery which got very high compatibility when it comes to install anything from zip via recovery where almost all roms do work stable with TWRP.
omg brilliant @nitrous² ! thanks so much! its been days i keep trying to deodex with others tool...
Sachitoge said:
Don't know if someone can help me as you stated that you're retired from this thread.
I did every step you do mentioned here (for self deodexing existing rom)
I did everything successfully and deodexed my files with 2.5 deodexer, putted files in the system folder to the 7zip folder and sent to my device and flashed zip, cleaned cache and dalvik and it stuck on booting for about 15 minutes. I know, it takes alot time during rebuildup of cache, but guys, it's 15 minutes! for me, if i cleanup cache and the dalvik/art cache, it just takes 1minute on boot screen to show up the image of each apps cache, but i just sat there with lots of patient for 15 minutes or a bit more and still same, stuck in same crappy booting logo.
I did restore my system files, now i'll try to retry it and send it again. Im suspicious of the zip file being corrupted during trasmitting to Device, however install was a big success so im very sure it wasnt corrupted. I'll do 2nd test and see it again if it's happening again.
If it does, i'll most likely try to figure out other ways to deodex as there is already deodexed roms out there, so they must have done is somehow.
Thanks, hope someone can help me out with this.
P.S: My adb works fine, i got usb drivers for my device, i got usb debug on, i got lots of space on phone, i got TWRP recovery which got very high compatibility when it comes to install anything from zip via recovery where almost all roms do work stable with TWRP.
Click to expand...
Click to collapse
Same happened to me.... Did you solved this problem?
Maurizio1953 said:
Same happened to me.... Did you solved this problem?
Click to expand...
Click to collapse
Nope, i ended up using CM12 (at that time, right now i got cm13 update).
Well i had to deodex apps to get xposed on TouchWiz, but i failed and didn't get headache because of the Xposed modules being not really well compatible on TouchWiz, so i jumped to CM, i find it more stable, and the CM13 is insane because it saves so much battery at stand by, compared to lollipop, the Android 6.0.1 Marshmallow is the biggest update in android history, that saves hell lot of battery (it can be also maybe because i don't have Xposed Framework in recent rom).
Anyway, im tired of it, and i don't need to hassle with Link2Sd because of Android Marshmallow offering to mount the SD Card, in the end, all my needs are being offered in this (for me) huge, best android update, being Marshmallow.
Try it i would say, so amazing.
Ok i would like to go to cm13 as you but i stil need the support to the gear s smartwatch so i decided to stay with touchwiz without xposed.
Related
This is a modified OpenRecovery (Skrilaz_CZ) based on Androidiani Recovery (89luca89&Azhad) with some enhanced features for Milestone XT720.
Features:
Main OR menu streamlined
Most Androidiani menu options have been moved into OR > Other Utilities
Add ext3/4 support (thanks fjfalcon)
Added SD Card Utility (OR > SD Card Utility)
Added preference for display brightness in OR (OR > Settings > Brightness)
Added utility to reinstall orbootstrap (OR > "Other Utilities" > "Re-install orbootstrap")
New sh hijack binary will boot to fastboot bootloader if volume-down is held (OR > "Other Utilities" > "Re-install orbootstrap" to enable). This should be compatible with all ROMs and stock.
nandroid: removed ability to backup partitions that always fail (this means "Backup All" works now)
Fixed OR > "Wipe Dalvik Cache" bugs (previous OR/AOR don't clear them all)
Added OR > "Power Off" (helpful when phone is being stupid about charging)
Minor update to sdcard-info.txt output
XT720 basebands added (OR > Change Basebands)
Please note that although most Androidiani menu options have been included in the Other Utilities menu item, that does *not* mean I have tested them on XT720.
Installation:
Download link: http://www.multiupload.com/J8Q15SHP4S
Root the phone
Download OpenRecovery-XT720-01.zip (it contains /sdcard/OpenRecovery and /sdcard/OpenRecovery.zip)
Extract OpenRecovery-XT720-01.zip onto the SD card. This will create a /sdcard/OpenRecovery directory and an /sdcard/OpenRecovery.zip file.
Make sure you're not in USB access mode and install the bootstrap (using adb or Terminal):
Code:
su
cp /sdcard/OpenRecovery/orbootstrap/install_script.sh /tmp
chmod 755 /tmp/install_script.sh
/tmp/install_script.sh STR
Upgrading from OpenRecovery:
Download link: http://www.multiupload.com/J8Q15SHP4S
Make a nandroid and backup your sdcard
Download OpenRecovery-XT720-01.zip (it contains /sdcard/OpenRecovery and /sdcard/OpenRecovery.zip)
Rename the old /sdcard/OpenRecovery folder to /sdcard/OpenRecovery.bak
Extract OpenRecovery-XT720-01.zip onto the SD card. This will create a new /sdcard/OpenRecovery directory.
Optional: Move/copy all files from /sdcard/OpenRecovery.bak/updates to the new /sdcard/OpenRecovery/updates directory
Optional: Reboot into OR. Select "OR" > "Other Utilities" > "Re-install orbootstrap"
Github: https://github.com/Mioze7Ae/openrecovery_xt720
Thanks: skrilax_cz, 89luca89, Azhad, fjfalcon
Is this the same update that was posted in other topics?
No, it's not the same, its the next version. The biggest difference is this one merges Androidiani (the previous one was based on vanilla OpenRecovery). Maybe I should bold the new stuff.
Sorry about this but what does Reinstalling the Bootstrap mean? Don't we already use that for getting in the bootloader? Is it is it gets broken somehow?
Woodrube said:
Sorry about this but what does Reinstalling the Bootstrap mean? Don't we already use that for getting in the bootloader? Is it is it gets broken somehow?
Click to expand...
Click to collapse
If the bootloader gets broken, you won't be in OpenRecovery
Anyway, I see two reasons to use it. (1) to make 100% sure you can get back to OpenRecovery after you've flashed something experimental (say a Milestone A853 update-based ROM) or (2) you want to upgrade your bootstrap to the new version that lets you hold volume-down to boot directly into the fastboot bootloader. (i.e. in the new version volume-up==OpenRecovery, volume-down==fastboot)
Edit: that reminds me... I should make a version of the bootstrap that fixes volume-down to boot OR on Milestone XT720 running Motoroi 50R...
Mioze7Ae said:
If the bootloader gets broken, you won't be in OpenRecovery
Anyway, I see two reasons to use it. (1) to make 100% sure you can get back to OpenRecovery after you've flashed something experimental (say a Milestone A853 update-based ROM) or (2) you want to upgrade your bootstrap to the new version that lets you hold volume-down to boot directly into the fastboot bootloader. (i.e. in the new version volume-up==OpenRecovery, volume-down==fastboot)
Edit: that reminds me... I should make a version of the bootstrap that fixes volume-down to boot OR on Milestone XT720 running Motoroi 50R...
Click to expand...
Click to collapse
Very very nice... thx man
Ok so I may have run into a glitch. Hopefully it is just mine, but it has been awhile since I had updated many of the apps from the market and let me tell ya, there was a shopping list. Haha get it. Anyways, I updated them all and decided it has also been some time since I had made a backup as well.
So I went in and "tried" to make a backup of the usuals (system, data, cust, cache, cdrom and sd). I probably tried 3 or 4 times and it never backed anything up. I even deleted the openrecovery folder and re-unzipped and replaced it and tried maybe another 3 times. It would just hang on the system dumping part for 15+mins (which is way too long).
I rebooted and put the original MZor back in there (the one w/o all the AOR stuff in it-for reference). Booted into recovery and boom, made the full backup in normal time. I ran checks on sd and sd-ext several times throughout and never a problem.
Has anyone else encountered this? I had been using this since it first came out and some of the utilites and all worked fine, but now that I think of it, hadnt tried to make a back up until last night.
***Side question: Since the beginning when I first learned how to make a backup, I read that you should backup system, data, cust, cache, cdrom and sd(if neccessary). My question is why do we and does it matter if we back up the cust, cache and cdrom parts? Wouldn't these get repopulated anyways at first boot? Would everything work if we just restored system, data and sd (again if neccessary)
Woodrube said:
Ok so I may have run into a glitch. Hopefully it is just mine, but it has been awhile since I had updated many of the apps from the market and let me tell ya, there was a shopping list. Haha get it. Anyways, I updated them all and decided it has also been some time since I had made a backup as well.
So I went in and "tried" to make a backup of the usuals (system, data, cust, cache, cdrom and sd). I probably tried 3 or 4 times and it never backed anything up. I even deleted the openrecovery folder and re-unzipped and replaced it and tried maybe another 3 times. It would just hang on the system dumping part for 15+mins (which is way too long).
I rebooted and put the original MZor back in there (the one w/o all the AOR stuff in it-for reference). Booted into recovery and boom, made the full backup in normal time. I ran checks on sd and sd-ext several times throughout and never a problem.
Has anyone else encountered this? I had been using this since it first came out and some of the utilites and all worked fine, but now that I think of it, hadnt tried to make a back up until last night.
***Side question: Since the beginning when I first learned how to make a backup, I read that you should backup system, data, cust, cache, cdrom and sd(if neccessary). My question is why do we and does it matter if we back up the cust, cache and cdrom parts? Wouldn't these get repopulated anyways at first boot? Would everything work if we just restored system, data and sd (again if neccessary)
Click to expand...
Click to collapse
I don't backup cust or cdrom. I made a backup with Mz's new O.R. yesterday and good thing I backed up ext cause my XDA Special backup would not boot without it. Not much help for ya sorry bud Hope you get it worked out.
@Mioze7Ae
can you please compile a standalone APK installer version of the new open recovery for XT720?
after reading the instructions i noticed, it requires an existing open recovery already installed to apply the above updates
AllGamer said:
@Mioze7Ae
can you please compile a standalone APK installer version of the new open recovery for XT720?
after reading the instructions i noticed, it requires an existing open recovery already installed to apply the above updates
Click to expand...
Click to collapse
I tried but my re-compiled version of the OpenRecovery.apk just FC'd.
Thanks for this Mioze7Ae, this is really sweet!
Am I missing out something here? I don't seem to be able to get the additional OR menu to convert to EXT4. I flashed back to Singapore 2.1 and have rooted. Removed the previous Open Recovery folder but where do I get the OpenRecovery.apk? Do I use back the previous version?
You can use Dexter's OpenRecovery.apk to install Open Recovery & then follow Mioze7Ae's instructions in the OP to update it.
Not sure what effect it even has, but the set timezone seems to be backwards ... Selecting GMT-7 runs /bin/timezone.sh GMT+7 and selecting GMT+7 runs /bin/timezone.sh GMT-7
Hey guys, hope you can provide me with a clearer instruction. I have done exactly as per the instructions and now when I boot into recovery, I don't see the extra option to convert to EXT4. The only things I see in the menu is:
Motorola MILESTONE XT720 Open Recovery
Version 1.46
Created by Skrilax_CZ
Use Volume Up/Down to highlight:
Camera_Mode key to select.
Main Menu
Reboot Menu
Settings
USB Mass Storage Mode
Nandroid
Application Menu
Run Script
Apply Update
Wipe Dalvik Cache
Wipe Data / Factory Reset
Wipe Cache Partition
What am I doing wrong? The phone is still running 2.1 update 1 but it's rooted.
It looks like you're running the original OpenRecovery. You need to replace the OpenRecovery folder on the sdcard with the version from the OpenRecovery-XT720-01.zip.
I think I can see how the instructions about renaming might be confusing so I tweaked the phrasing a little bit.
Thanks for the reply Mioze7Ae but I followed exactly as your instructions. Here's what I've done:
-Flashed singapore_STR_U2_01.1E.0
-Rooted with SuperOneClick
-Extracted and transferred to SD the OpenRecovery folder, OpenRecovery.zip and the original OpenRecovery.apk file.
-Ran OpenRecovery.apk
-Install Recovery System. Install Sucess.
-Recovery Boot and that's where it boots into the old OR.
It's the same if I use the OpenRecovery folder provided by hellmonger in The XT720 XDA Special Final RC2 "Hellmonger Edition"
ranggie4 said:
Thanks for the reply Mioze7Ae but I followed exactly as your instructions. Here's what I've done:
-Flashed singapore_STR_U2_01.1E.0
-Rooted with SuperOneClick
-Extracted and transferred to SD the OpenRecovery folder, OpenRecovery.zip and the original OpenRecovery.apk file.
-Ran OpenRecovery.apk
-Install Recovery System. Install Sucess.
-Recovery Boot and that's where it boots into the old OR.
It's the same if I use the OpenRecovery folder provided by hellmonger in The XT720 XDA Special Final RC2 "Hellmonger Edition"
Click to expand...
Click to collapse
Change this:
Extracted and transferred to SD the OpenRecovery folder, OpenRecovery.zip and the original OpenRecovery.apk file.
Ran OpenRecovery.apk
Install Recovery System. Install Sucess.
To this:
Transferred to SD the the original OpenRecovery.apk file.
Ran OpenRecovery.apk
Install Recovery System. Install Sucess.
Extracted and transferred to SD the new OpenRecovery folder, OpenRecovery.zip
R-D said:
Not sure what effect it even has, but the set timezone seems to be backwards ... Selecting GMT-7 runs /bin/timezone.sh GMT+7 and selecting GMT+7 runs /bin/timezone.sh GMT-7
Click to expand...
Click to collapse
I think it only affects the naming of the nandroid directories, but I'll give it a look. Nice catch!
Thanks Mioze7Ae. The last instruction made it clear. It works now. Thank you so much!!!!!!!!
Mioze7Ae said:
I think it only affects the naming of the nandroid directories, but I'll give it a look. Nice catch!
Click to expand...
Click to collapse
it was like this in all the versions of open recovery...
+++++++++
Mioze, can you also add a wipe battery stats in your modified openrecovery? comes in handy when we flash a new rom or restore a nandroid so we dont have to use the battery calibrating app.
After having rooted (with nexus 10 toolkit v1.3.0) my nexus 10 and flashed AOPK Nexus 10 (WIP) Task650 & Ktoonsez (1-4) rom, I'm unable to upload to, change or move any files or folders on my internal SD card. I installed Root Explorer and changed from Mount R/O to Mounted as r/w. Access is granted by Super SU. I also tried to change permission settings, unfortunatedly without any success. There appeared the following message:
"Warning
Permissions change was not successful. Please note that some file systems (e.g. SD card) do not allow permission changes."
Is there a possibility to change these permissions in order to be able to create and move files and folders on my SD card?
Thanks for taking your time to help me with my issue!
Anzirothu
1. Clear cache
2. Clear dalvik
3. Fix Permissions
forgot something ?
Thank you for your reply, Patrik!
1. done.
2. done.
3. Fix Permissions - How? With cwm? I did fix permissions with cwm recovery, but the problem persists...
Just so we are clear, when you say "upload to, change, or move" are you meaning you cannot copy a file from your computer to your Nexus 10? Or just that you cant arrange stuff through root explorer from within the tablet itself?
Neither copying from PC to Nexus nor arranging stuff through root exlorer from within the tablet itself. I can't even download an email attachment and put it to the SD card. The card seems to be locked.
I had that problem once but I dont remember what caused it or what exactly I did to fix. I think I just did a complete wipe by locking and unlocking the bootloader and then installing a new ROM again.
I think I did this too (unroot, lock bootloader, then root and unlock bootloader) and then installed the same rom again. I will try it this time with another rom.
Isn't there really no other solution to get access to my SD card again??
Thx for your help!
Are you using a toolkit to unlock and root? If so them maybe it is not doing something right and it messing up a permissions somewhere. It could also be a driver problem on your PC with being unable to copy a file to the tablet.
Thank you for your help!
I am using the nexus 10 toolkit V1.3.0. Right now I'm trying to intall twrp recovery with a fully wiped sd card. No easy task fot me being a noob...
In ClockWorkMod, make sure that /data is mounted
Then download the Android SDK: http://developer.android.com/sdk/index.html
I usually put all the files just in C:/android-sdk-windows
Once you have it all there open up the SDK Manager and download all the additional files needed. You probably only need to download "Android SDK Tools" and "Android SDK Platform-tools", but I always download the other files for whatever version of Android I am running, in our case Android 4.2. That way I have them if I need to do something else.
Once downloaded, open the Android-sdk-windows/platform-tools directory. copy:
adb.exe
adbWinApi.dll
adbWinUsbApi.dll
fastboot.exe
to your base C:/Android-SDK-Windows directory.
Now open command prompt from Start -> run
type: cd C:/Android-SDK-Windows
type: "adb devices" and it should list your tablet. It will actually say something with your devices serial number and then "Recovery" after it, showing your tablet is in recovery. If you dont see this then you either dont have your tablet mounted right from in the Recovery, ClockWorkMod is stupid, or you dont have working adb drivers.
Now copy the ROM you want to flash to C:/Android-SDK-Windows
Then type: "adb push blahblahblah.zip /data/media/0"
That should push the ROM to the root of your SD card. Give it time, it takes a while to push a ROM file. Once it is done, flash the ROM.
That *should* put it in the right spot where it looks like it is on your "internal storage" (what you see when navigating files within the ROM). If you dont see the ROM in clockworkMod then keep navigating back to the root of your internal storage and then open up "data", then "media", then "0" and you should see it. If you still cant find the ROM, push it again but just use "/data/media" as the location.
I just did all these steps myself to verify I remembered it all correct and I was able to successfully copy a ROM and find it on my tablet to flash by doing everything I just listed above. SO you should be good to go if you follow all those steps properly. I know it looks like a lot of work, but it really isnt and will go quite fast. Most of it is just the setup for getting ADB and Fastboot ready to use.
For a ROM to install, I would recommend to someone new like you either of these:
http://forum.xda-developers.com/showthread.php?t=2071082
^^^^^ That one is pretty close to the stock ROM with a few fixes and a couple extra features
or: http://forum.xda-developers.com/showthread.php?t=2071082
^^^^^ This one is pretty much CyanogenMod 10.1, but built by a different guy and not pulling every new thing from CM, just the "cherry picks" of features. It tends to be a bit more stable and less buggy than the real CM10.1 nightly's
And for a kernel you can flash and forget you will want to try this one:
http://forum.xda-developers.com/showthread.php?t=2098157
^^^^^ To flash that you will want to do a similar thing as how you pushed the ROM to your device. Only this time you will copy the kernels' "boot-r4.img" file into your android-adk-windows directory and use the command: "fastboot flash boot boot-r4.img"
While I enjoy the KTManta kernel more, it does require a bit of tweaking to get running perfect. Which is one of the things I like about it because of all the options to tweak. But for someone just learning this stuff that would be a bad thing, so Franco's kernel is much better than stock and doesnt require you to adjust anything once it is flashed to your tablet.
WARNING: BEFORE YOU DO ANYTHING PLEASE READ THIS THREAD AND MAKE SURE YOU KNOW WHAT YOU ARE DOING. I AM NOT RESPONSIBLE FOR ANY DAMAGE TO YOUR PHONE.
A few days ago I came across this thread which made me think and try. At the beginning I couldn't flash the zips necessary for making backups without rebooting to recovery .
What you will need:
1.Bootloader unlocked and a rooted phone . If you don't have any of them please read here and here
2.Busybox
3.A root explorer of your choice
4.A terminal emulator app
5.The 2 files from the zip attached
6.Patience
Open your root explorer extract and copy the 2 files attached to /system/bin and set permissions 755( that's rwxr-xr-x).
Reboot your phone.
Open Terminal app and type su to obtain root followed by onandroid.
Sit back and relax while the script backs up your rom.
All thanks go to ameer1234567890 who gave us the Online Nandroid . I only found the thread and also found the method to copy the files to Razr I.
When i'll have some time i'll try to make a flashable zip for the lazy ones
As promised here are the zips for flashing from recovery with update binary working with the Razr I. I have only tested with CWM, but they should work with TWRP as well.
I suppose everyone knows what to do, but just in case someone new tries it:
-copy the 2 zips to you internal storage or external sdcard
-reboot to recovery
-select install zip from sdcard(now choose the location of your files)
-select zip
-install
-reboot
Enjoy
nandroid,etc, assistance
free2live said:
As promised here are the zips for flashing from recovery with update binary working with the Razr I. I have only tested with CWM, but they should work with TWRP as well.
I suppose everyone knows what to do, but just in case someone new tries it:
-copy the 2 zips to you internal storage or external sdcard
-reboot to recovery
-select install zip from sdcard(now choose the location of your files)
-select zip
-install
-reboot
Enjoy
Click to expand...
Click to collapse
Is this the best way to do a " nandroid " - I have been part of this site for quite some time , read numerous sites, but i have a very bad memory problem and that's why i have many text documents setup to the point i am confused. Right now I have an AT&T S4 which has a bad IMEI, so I want to use it as a test phone, but it has been updated to 4.3 -which from what I understand I would need to downgrade back to 4.1.2 order to unlock the phone via the dial pad. I was able to accomplish that one time when I first got a Samsung S4 and did it via the dial pad before the OTA came out for 4.3.
I also own a S3, also AT&T, so i can learn how to to root and unlock and use CWR or TWRP and than learn ROMS. I know I need to make a backup before I do anything, and also constantly reading the " Noob " general forums for both phones. I also am familiar with Samsung Kies, which does a backup but I don't think it's the same as this nandroid i have been reading about.
Thank you or taking out the time and reading my post. I will check back to see if anyone had some time to give me some direction or an answer to my problem with " nandroid" or if someone even could touch up on any subjects I have mentioned. Please don't think I haven't spent hrs of time on YouTube, Google, Howard forums and especially here on XDA.
Only valid for Moto G 2014!
Hello, forum mates. I have spent few days with this great device, I gave it meanwhile to my sister as present.
ATM, there are barely any custom ROMs, so I will list here few good things to do right after unlocking its bootloader and obtaining root access :angel:
So here you can read my little checklist and do whatever you prefer:
DISCLAIMER:
Code:
[I]your warranty is now void. All you do
with your phone is on your own risk!
Partitions info is valid for XT1068
international GSM dual-SIM only! Workflow
is tested only on KitKat factory image![/I]
Click to expand...
Click to collapse
Unlocking Bootloader: Motorola's website
Removing startup screen with warning of unlocked bootloader: flash attached zip in custom recovery
(I can confirm that the attached zip works, it will restore the white original Motorola splash screen)
1. Boot custom recovery without flashing it:
Copy and paste custom recovery (file format: img) into your SDK/platform-tools folder, I recommend here TWRP_2.8.0.1_Titan_v2 that I have successfully tested myself. Until this point the latest Motorola USB driver must be installed on your Windows PC, USB debugging (under "developer options") on your phone must be enabled. However, I generally recommend using Linux instead of Windows. You can check in my short guide for Ubuntu users how to install fastboot and ADB in Ubuntu. I have no clue about Mac iOS, sorry.
Here we go:
Navigate in CMD line into the directory where your adb.exe is saved. Example on my PC, it is in the folder "AndroidSDK", and there in the folder "platform-tools". So my commands would be:
Typing on keyboard Win+R
Enter cmd
the command line appears after that
Code:
cd c:\androidsdk\sdk\platform-tools
Now I'm in my desired folder. The next command is checking the USB driver / ADB connection:
Connect the phone to with your PC via USB cable and enter in cmd:
Code:
adb devices
Correct response:
HTML:
xxx(serial No)xxx device
If you don't see serial No of your Moto G, check if USB debugging is enabled. If serial No is there but "offline" instead of "device" appears, you will only have to confirm the promt on your phone's screen to allow USB debugging. If nothing appears, try to update your USB driver (don't go any further without working ADB connection!)
Now we will boot into bootloader mode and check there if fastboot connection is also working:
Code:
fastboot devices
Correct response:
HTML:
xxx(serial No)xxx fastboot
If the response looks like that, we can now boot into the custom recovery without flashing it onto device. The recovery.img will be booted directly from "platform-tools" folder, while stock recovery still remains installed on the phone. My recovery.img file's name is for example "TWRP-Titan", so after I've previously saved it in my "platform-tools" I will now enter in cmd:
Code:
fastboot boot TWRP-Titan.img
The phone will boot into the beautiful touch-recovery TWRP. Blue screen is there? Yesssss!! :good:
Now we can start with backups of our still 100% stock firmware in the next chapture.
Click to expand...
Click to collapse
2. Backup your stock firmware:
While still in the TWRP, simply create backup of all your partitions. It is strongly recommended to save backup on the external SD card, as many modifications or next unlocking of the bootloader (if relocked) will every time blow all your data from the internal memory.
Now still in TWRP, install SuperSU.zip
Reboot into the system
Now we will backup stock recovery, that we can later flash at any point back:
Code:
adb shell (enter)
su (enter)
Look at this point on the screen of your phone, SuperSU will promt you to allow SU access for shell, You should confirm that.
Code:
dd if=/dev/block/mmcblk0p32 of=/sdcard/recovery.img
It will save the "recovery.img" file in your /sdcard folder on your phone's internal memory. It is strongly recommended to create the new folder on your external SD card where you can move all backup img files. To move the files, use any root file browser like for example Root Browser. When you open Root Browser for the first time, it will prompt oyu to install few utilities (busybox, unrar etc) which you should allow.
At this point, your entire stock firmware has been saved as backup.
Click to expand...
Click to collapse
3. Backup all partitions of your factory image / firmware:
Just the same way as you have previously created backup of your "recovery.img" you can
create "img" backup files of all your partitions. Check the attached screenshots and simply replace in the adb shell command the number of the mmcblk0p block No with the one you desire to backup and change "recovery" to the proper partition names, just like in the screenshots:
Click to expand...
Click to collapse
4. Restore to 100% stock firmware:
To return to 100% stock, you simply need to flash (or only boot) again TWRP 2.8.0.1, to restore your nandroid backup of your stock firmware and -if custom recovery was flashed- to flash in bootloader mode your stock recovery back. Paste your (stock) "recovery.img" file into "platform-tools" folder and execute in bootloader mode:
Code:
fastboot flash recovery recovery.img
After that simply restore your TWRP backup of stock and flash in bootloader mode your stock recovery back. To unroot permanently, open SuperSU app and choose the option "Full unroot" under "settings".
To relock the bootloader again: reboot to bootloader mode and execute in cmd:
Code:
fastboot oem lock
Your Moto G should be now again 100% stock.
Click to expand...
Click to collapse
If you benefit from this guide, show me your love and please hit "THANKS" button.
Credits also to all guys who have created linked guides (please hit there "thanks" also)
EASY MODS (Moto G 2014 stock firmware)
I am myself very big fan of SlimRoms (I was AlphaBeta SlimKat tester on few devices), so I was desperately missing the "Real Dark Slim" mode (and several other mods) on the Moto G 2014 factory image 4.4.4
I had to darken my Moto G 2014, so here I share now quite easy way how to get dark UI on many apps:
Click to expand...
Click to collapse
DARK UI APPS:
On the attached screenshots is an example of the "normal" Play Store (light UI) YouTube app vs the modified, dark UI YouTube app.
Luckily, the Team BlackOut consisting out of some great developers and contributors has darkened out whole bunch of apps. Please visit their website or please visit their thread where you can get more info and download directly the app TBO updater (ver.5.0.0 is up to date ATM, it is a lot better than the v.3 which was suffering of regular FCs on many devices).
With the TBO app you will find also boot animations, wallpapers etc and info how to install, the most important to avoid data loss and crying is: don't forget to create nandroid backup before modifying!
List of modified apps by the TBO available in dark UI (choice, uncomplete list):
Apollo music
Calendar
Chromecast
Drive
DropBox
Ebay
ES File Explorer
Facebook
Google now
Google+
Gmail
Hangouts
Instagram
Keep
MMS (AOSP)
Netflix
PayPal
PlayStore
WhatsApp
Skype
Spotify
Translate
Twitter
YouTube
etc.
Small tipps for the flawless un/installation of the system apps:
Regarding the fact that issues could occur when replacing the system apps (probably caused by smaller scripts which might remain as "corpses" after removing the apps) here is quite reliable way to go:
gain root access (flash SuperSU zip in custom recovery)
backup all apps that should be replaced with the darkened ones (recommended: Titanium Backup to create backup, or SD Maid to create *apk file)
now uninstall the respective apps (also with TB or SD Maid)
Open Play Store, install again and uninstall respective apps (that will remove reliably all rests)
Install the darkened apps (apk files or flashable zips that you have downloaded with TBO Updater)
Enjoy dark apps!
TROUBLESHOOTING: If anything goes wrong (bootloop, dark app FCs etc) delete darkened app and restore your app backup. I have never faced bootloop, but some apps simply might not work and will FC. Even if somebody would face bootloop, restoring the nandroid backup will revert all changes.
For normally installed apps (non-system apps): simply uninstall them through Play Store and install darkened ones instead. If TBO apps don't work, uninstall them and install again from the Play Store normal versions.
Click to expand...
Click to collapse
All credits here go to @djdarkknight96, @B_Boytm, @Gunthermic, @dafoxs, @train, @darkknight and our beloved SlimGapps maintainer, @dankoman :highfive:
Sorry, if I forgot to mention someone- remind me please!
(please if you use their modified apps, don't forget to find some posts of those guys here on forum and hit several times "thanks" button!)
Xposed frameworks
Add hunderds of mods, change functions of your hardware buttons, add double-tap-to-sleep, make your phone to fly etc, endless mods possibilities with Xposed frameworks (main thread)
Little guide for people who never used Xposed frameworks before:
download Xposed installer apk (v. 2.7 experimental is my recommendation for 4.3 and newer firmwares)
download also Xposed-Disabler-Recovery.zip from the main thread (if anything goes wrong)
create nandroid backup!
install Xposed installer app
open the app and Install/Update framework
reboot
if anything goes wrong, you end up with bootloop or so, reboot recovery and flash Xposed-Disabler-Recovery.zip (if even that doesn't help, restore nandroid backup)
if the phone reboots fine (it should) download modules you desire to use and install them
reboot
enjoy your new, customized firmware
If you find this post useful, please hit "THANKS" and honour my time spent to share this with you. Please also hit thanks to all devs and contributors whose work brought you benefits.
Click to expand...
Click to collapse
Hope to see soon more tweaks from you
Gerriitw said:
Hope to see soon more tweaks from you
Click to expand...
Click to collapse
I will post in the second post few more ideas with smaller mods on the stock firmware like using dark UI apps, some useful little frameworks modules, debloating etc.
This thread is actually not so interesting for experienced users, it's all quite common stuff.
tetakpatalked from Nexus 7 flo
Very helpful for newbies....U have done great job...hope to see more...
Second post updated (mods of stock 4.4.4 firmware)
Welcome to a simple tutorial that will help OnePlus 2 (OP2) owners and possibly other device owners install custom ROMs in such a way that eliminates most, if not all possibility of system errors, resulting in the longest lasting and most stable custom ROM installations!
DISCLAIMER: Your Warranty was voided long before you were ever even ready to complete this tutorial.
Therefore, I am not responsible for a broken or bricked device, especially if your rage towards a bricked device caused you to throw your device into a wall. This tutorial is actually designed to reduce the amount of "Rage Quitting" on modifying your device.
This Tutorial assumes you have already completed OEM Unlock, Root, installed TWRP or other Custom Recovery, and are basically ready to install a custom ROM on your OP2.
Before beginning, backup any files you may need, I upload mine to my Google Drive then download after completing the ROM install. You can also use Nandroid to backup your current system (optional as there are methods to restore even the most bricked OP2 that doesnt even have a working recovery or OS, trust me I have done it at least 5 times because I constantly try new ROMs and mods). There are three necessary prerequisite steps required to complete before using this method to install your custom ROM. These prerequisites are listed below:
Prerequisite One: Ensure your OnePlus 2 has been FULLY updated on the stock Oxygen OS ROM before you install your TWRP or other Custom Recovery. If not, Return to factory ROM, Un-Root, and update until you cannot update any more, then return to this tutorial afterwards.
Prerequisite Two: Ensure your OnePlus 2 has the latest update of the TWRP or other Custom Recovery. The Latest TWRP for the OP2 can be found here: https://twrp.me/oneplus/oneplustwo.html
Prerequisite Three: Ensure your device can receive files via ADB PUSH while in custom recovery. To do this, reboot your phone into recovery, connect to PC, hold down the "Shift" key and while holding, right-click in a window containing a file you wish to transfer, and select "Open Windows PowerShell Here" or "Open Command Prompt Here". Use the command "adb push Lin15.zip /sdcard" (remove the quotes, "Lin15.zip" is an example file) to push the file onto your device. Then, if your custom recovery has a file explorer as TWRP does, use it to navigate to /sdcard and see if the file is there. Also, your windows should show a successful transfer and should say "Okay" underneath your command line. If unsuccessful, install OnePlus 2 Drivers along with Universal ADB drivers and then try again. If still unsuccessful, try TWRP 3.1.1-0 (Download Link Below 2 Paragraphs in Blue Text Section). If unsuccessful at this point, there is something wrong as Win 10 with OP2 Drivers, Universal ADB Drivers, and TWRP 3.1.1-0 is my exact setup.
There are many custom ROMs available for the OP2. The method for installing custom ROMs is generally the same, but can differ in certain ways. This method SHOULD work for your custom ROM, but is not guaranteed. If this method fails, then visit your custom ROM's development page, and follow their instructions instead.
In this Example, I will be installing the latest (at the time of writing) Lineage 15 Android Oreo 8.0 Third Alpha Build OS/ROM and will be including instructions for the proper installation of the A.R.I.S.E. Magnum Opus System Sound Mod (Based on Viper4Android). I will include links to downloads, but their main XDA page can be found here: https://forum.xda-developers.com/android/software/r-s-e-sound-systems-auditory-research-t3379709 This installation will use the latest (at the time of writing) TWRP 3.1.1-0 Custom Recovery.
INSTALL TIME:
Begin by rebooting into recovery. Under "Wipe" options, you will first want to format data, select the option and type "yes" when prompted to confirm the operation. Repeat this step once again to ensure a squeaky clean wipe.
Next, also under "Wipe" Options, select the "Advanced Wipe" Options. You will then select EVERY BOX (Yes, this includes Internal Storage and will wipe EVERY SINGLE FILE from your device, this is INTENTIONAL and is why you MUST have a device that can accept ADB PUSH files in recovery!). This will wipe every file from existence, completely. This is what allows such a stable, squeaky clean install, as not a single piece of evidence from any other ROM/OS will be left behind, leaving basically no chance for errors or conflicts during installation of new ROM. You will want to complete this step again to ensure a squeaky clean wipe.
Navigate to the TWRP Home/Start-Up Screen and connect your device to your PC (WARNING: DO NOT USE ADB SIDELOAD MODE!!! I HAVE NEVER, EVER HAD A SUCCESSFUL ROM INSTALL FROM SIDELOAD!!!). Simply leave the device at this screen, and do not touch it. At this point, if you do not have all the necessary files to install your custom ROM and mods, you will need to download them now. I ALWAYS recommend the "Pico" Gapps package if installed in a ROM (some ROMs include Gapps). The reason for this is because the Pico package includes the bare minimum to get Google Play Services and Google Play Store up and running. This eliminates unwanted Gapps and reduces the chance of installation conflicts. The golden rule is: The less you install in TWRP, the better. If you want more Gapps, then after setting up the phone at the end of the ROM install, just search for them in the Google Play Store, its how I get mine every time. In the case of Lineage 15, the list of downloads is below:
Lineage 15 OS/ROM: https://www.androidfilehost.com/?fid=961840155545594199 (Dev Page: https://forum.xda-developers.com/oneplus-2/development/rom-lineageos-15-0-t3668056)
Android Oreo 8.0 Pico Gapps Package: https://www.androidfilehost.com/?fid=817550096634796662
Super SU 2.82 Root Installer (Select the Flashable 2.82 ZIP file): http://www.supersu.com/download
BusyBox Flashable Zip Package (Large page with many tools, scroll down to find the BusyBox tool): https://forum.xda-developers.com/showthread.php?t=2239421
A.R.I.S.E. Magnum Opus System Sound Mod (Select the "ARISE+Deuteronomy+2.94+Modular+AROMA+Installer.zip" Option): https://www.androidfilehost.com/?w=files&flid=176171
Once all necessary files are downloaded, give them their own folder inside Windows and rename all of them to something simple as shown here:
View attachment 4273530
(Lin15.zip, Gap.zip, SU.zip, Busy.zip, Arise.zip)
Ensure your device is in custom recovery at the home/startup screen and is plugged firmly into your PC. DO NOT navigate ANYWHERE inside custom recovery or touch the device.
Now we will ADB PUSH these fresh install ZIP files over to your device. Inside the window containing your downloaded ROM files, hold down the "Shift" key and while holding, right-click and select "Open Windows PowerShell Here" or "Open Command Prompt Here". To ADB PUSH files, simply type "adb push FILE.zip /sdcard" where "FILE" is the target file and "/sdcard" is the target destination. Correct capitalization of letters is IMPORTANT! My window looked like this when finished:
View attachment 4273532
(adb push Lin15.zip /sdcard, adb push Gap.zip /sdcard, adb push SU.zip /sdcard, adb push Busy.zip /sdcard, adb push Arise.zip /sdcard)
Your ROM files should now appear on your device at your target destination. Disconnect your device and use the Custom Recovery File Explorer to navigate to the destination to confirm. "/sdcard" is the easiest to use destination.
Now we will install ALL of the ROM files, back-to-back with NO REBOOTS, NO WIPES, NO OPERATIONS WHATSOEVER INBETWEEN INSTALLS, THIS IS EXTREMELY IMPORTANT!!! Navigate to the Custom Recovery "Install" Section and navigate to your destination for your files. Flash the ZIP files in this order EXACTLY: Lin15, Gap, SU, Busy, Arise.
The A.R.I.S.E. Instillation is an AROMA style installer. It is a HUGE Sound Mod suite containing many options. Select the sound mods you like, but there is a module that is REQUIRED and 4 others that are highly recommended, listed below:
CORE Module is REQUIRED!!! Uninstall MusicFX, Remove Deep_Buffer, Set SELinux to Permissive, and SD Card Permissions fix are all highly recommended no matter what the ROM or mods, just in case. If these problems do not exist, selecting the options will not change anything, so do not worry.
My personal A.R.I.S.E. install included the following modules and delivers absolutely AMAZING sound quality while keeping installed modules to a minimum (otherwise known as a "Lightweight" install): Core Module, Viper4Arise 2.5.0.5, Viper4Arise Profiles, Uninstall MusicFX, Remove Deep_Buffer, Set SELinux to Permissive, and SD Card Permissions Fix. Its a highly recommended package
ONLY AFTER ALL FILES HAVE BEEN INSTALLED, navigate to Custom Recovery "Wipe" section, select "Advanced Wipe" and then check the "Dalvik Cache" and "Cache" options, DO NOT SELECT ANYTHING ELSE OR YOU WILL NEED TO START COMPLETELY OVER, WIPE PHONE AND RE-ADB PUSH FILES TO ENSURE A SQUEAKY CLEAN INSTALL!!! Perform this step again to ensure a squeaky clean wipe.
YOU ARE NOW FINISHED WITH A SQUEAKY CLEAN ROM INSTALL BUT THERE ARE A FEW MORE RECOMMENDED STEPS!
Recommended: DO NOT immediately reboot into system after install. Instead, navigate to Custom Recovery "Reboot" Section and select "Power Off" Instead. Once device is off, plug into A/C Outlet charger (DO NOT USE A PC, DETECTION OF PC WILL CAUSE DEVICE TO BOOT), and allow to fully charge, then cool off. This will ensure that Battery Calibration is set to 100% upon Initial Boot
Initial Boot: Boot Device, Initial boot will take around 5-10 minutes. DO NOT TOUCH THE DEVICE DURING THIS TIME. When you see the startup screen, STILL DO NOT TOUCH THE DEVICE! Instead, allow device to sit and idle, allowing the ROM to "Settle" for a MINUMUM of 5 minutes, 10 is recommended. Then, BEFORE setting up the device, reboot and allow another 5 minutes of "settling".
Run through the Device Initial Setup. You will want to select any desired options now, and avoid having to search settings later. Once at Device Home Screen, immediately open app drawer and select SuperSU app. Inside SuperSU, navigate to settings and apply the following options:
Disable Re-Authentication, Default Access: Grant, Enable SU During Boot, Trust System User
These SuperSU options will allow mods to function with complete stability and no interference, leading to a smoother experience. After, completing this step, Reboot your phone and ENJOY YOUR NEW, ROCK-SOLID, STABLE ROM INSTALL!!!
Nice job bro thanks working here!
Nopes. It did not work out for me. I flashed ROM, Gapps, and Magisk before and landed on your thread and flashed only the ARISE zip. But it did not flashed properly and I got an error 1 or something like that. What could be the reason?
Why are people recommending using adb push to get the files on the phone.
I always just drag and drop them on the phone in windows explorer, never had any problems.
Only time I ever need adb is for flashing recovery.
shailinder said:
Nopes. It did not work out for me. I flashed ROM, Gapps, and Magisk before and landed on your thread and flashed only the ARISE zip. But it did not flashed properly and I got an error 1 or something like that. What could be the reason?
Click to expand...
Click to collapse
Now I tried it again and this time flashed busy box as well but the same error.
Screen shot for your reference. Is there another way to install it?
shailinder said:
Nopes. It did not work out for me. I flashed ROM, Gapps, and Magisk before and landed on your thread and flashed only the ARISE zip. But it did not flashed properly and I got an error 1 or something like that. What could be the reason?
Click to expand...
Click to collapse
Error 1 is what occurs on the non-AROMA older A.R.I.S.E. package install if you have not set up any settings in the customizable .prop file that comes with the ZIP. Upon initial install, this "Error 1" will install a .prop file under /sdcard. If you open this .prop file with a text editor, you can then use examples such as "install.core=true" to install the core. However, the AROMA installer requires none of this. And as far as I experienced, NONE of the other packages work on Lineage 15. You will want to delete whatever A.R.I.S.E. zip you have now, and follow my download link for the AROMA version. Then, wipe everything and perform a "Squeaky Clean" ROM install as shown in this thread, and it should work and be rock-solid stable.
pops106 said:
Why are people recommending using adb push to get the files on the phone.
I always just drag and drop them on the phone in windows explorer, never had any problems.
Only time I ever need adb is for flashing recovery.
Click to expand...
Click to collapse
Well we all know performing this method of install is not a requirement for installing ROMs, but it is the most fool-proof method and ensures there are no file conflicts between old and new ROMs/OS's. I cannot even tell you how many times I have done quick, minimal work installs and end up with tons of errors, laggy or freezing screens at random times, force closing apps, busybox system link failures, the list goes on and on. After using the "Squeaky Clean" method, I can honestly say Lineage 15 is as stable as the Stock/Factory Oxygen OS.
wallacengineering said:
Error 1 is what occurs on the non-AROMA older A.R.I.S.E. package install if you have not set up any settings in the customizable .prop file that comes with the ZIP. Upon initial install, this "Error 1" will install a .prop file under /sdcard. If you open this .prop file with a text editor, you can then use examples such as "install.core=true" to install the core. However, the AROMA installer requires none of this. And as far as I experienced, NONE of the other packages work on Lineage 15. You will want to delete whatever A.R.I.S.E. zip you have now, and follow my download link for the AROMA version. Then, wipe everything and perform a "Squeaky Clean" ROM install as shown in this thread, and it should work and be rock-solid stable.
Click to expand...
Click to collapse
Thanks. I got it install using a different method and it is working wonderfully.
wallacengineering said:
Error 1 is what occurs on the non-AROMA older A.R.I.S.E. package install if you have not set up any settings in the customizable .prop file that comes with the ZIP. Upon initial install, this "Error 1" will install a .prop file under /sdcard. If you open this .prop file with a text editor, you can then use examples such as "install.core=true" to install the core. However, the AROMA installer requires none of this. And as far as I experienced, NONE of the other packages work on Lineage 15. You will want to delete whatever A.R.I.S.E. zip you have now, and follow my download link for the AROMA version. Then, wipe everything and perform a "Squeaky Clean" ROM install as shown in this thread, and it should work and be rock-solid stable.
Click to expand...
Click to collapse
Fair enough
And thanks to the opp for the thread
pops106 said:
Fair enough
And thanks to the opp for the thread
Click to expand...
Click to collapse
No problem, the thread was a random idea after accidentally stumbling across the fact that TWRP can accept ADB PUSH files. I honestly had no idea, and was stuck in a bootloop after a custom ROM failed to install correctly. I had no backup and was getting ready to just give up, enter Qualcomm Diagnostics Mode and perform the Oxygen OS Firmware/Software OEM install when I decided to reboot into Recovery and attempt SideLoad of a previous ROM that had worked.
This did not work, as sideload is apparently a dumb way of doing things. I never understood why sideload tries to install a file that is in the middle of transferring. Just seems like a flawed concept to me. Anyways the install was very slow, buggy and laggy, and when finished had installed such a corrupt system, due to installing a partially transferred file while it is being transfered and then sticking all the pieces together, was so unstable that more than a minute idling at the home screen or any attempt to open ANY app caused the phone to reboot.
Sideload is a worthless feature in my opinion and I will never use it for any operation ever again so long as I live. So all of a sudden I decide to plug the phone into my PC while in recovery and observe how Windows detects the phone when you turn Sideload mode on and off, as to try and troubleshoot my sideload to get an effective install (which by the way will never happen, to this day I have never had a sideload install work correctly), and noticed when I turned it off, the device still showed up as a recognized Android device under Windows Device Manager. Then, you may not believe me on this, but I did actually randomly decide that more than likely, it was interfaced on Universal ADB, and that it I typed "adb devices" into a windows command prompt, it should show, and it did. The rest is history.
I know the feature had been around for some time as I found out later on, but I had never seen any information about it anywhere on any thread, and even when I asked for ideas for troubleshooting, while XDA users helped for sure, I guess they just didnt have that idea, and gave me alternative routes as well such as the Qualcomm Diagnostics full OEM wipe method which I was already familiar with. This does show, however; that experimenting and troubleshooting on your own can be a great way to learn new things!
Hi, thank you for the post.
I am enjoying v4a bcoz of you only.
I got a query btw, can I install dolby & atmos along with v4Arise?
Please add a note for HaruhiOS
HaruhiOS checks if a clean flash is required before flashing and will abort to tell the user that a clean flash is necessary if ever. It is my design goal to avoid the need for clean flashing as much as possible
Due to this the user should avoid unnecessary clean flashing, which actually ruins performance and battery life and reduces device health when using my ROM
if already.....
hey,
if one would already go thus far to wipe internal storage as well, i'd say that it's making sense to format storage by changen from ext4 to ext2 and back to ext4. wiping is not always getting us rid of all residues while changing the file system and going back to the one we want/need does indeed reformat everything, this is a procedure that is useful once the storage card is corrupted.
magnamentis said:
hey,
if one would already go thus far to wipe internal storage as well, i'd say that it's making sense to format storage by changen from ext4 to ext2 and back to ext4. wiping is not always getting us rid of all residues while changing the file system and going back to the one we want/need does indeed reformat everything, this is a procedure that is useful once the storage card is corrupted.
Click to expand...
Click to collapse
Apparently e2fsck and fsck.f2fs is too hard
Once the storage card is corrupt no formatting will help you anyways
Just stop believing in dumb stuff. If you have to clean flash every other build a ROM developer releases they messed up big time and they should fix their code