[Q] Defy stuck to bootmenu (solved) - Defy Q&A, Help & Troubleshooting

Greetings,
Quick history of the problem:
*I have a Defy, with stock rom, rooted, and TWRP 2.1. I have a full android backup with TWRP.
*I flash CM9-NIGHTLY-120716-Defy.zip. I reboot, everything is fine.
*I reboot into new CWM recovery, make another android backup with CWM.
*I install TWRP 2.1 again.
*I flash CM10-20120924-NIGHTLY-mb525.zip.
*But then, I immediately flash again TWRP 2.1 (I think that was a mistake).
*I reboot, CM10 works fine.
*But when trying to boot into recovery from (new) bootmenu, TWRP immediately crashes and phone reboots I have no recovery mode available.
*At this time, phone still boots into CM10 just fine.
*I spend many hours trying to find how to flash a proper recovery, but to no avail. In desperation, I then follow the same recovery install procedure I followed many time ago after rooting the phone (see for example "wiki.cyanogenmod.org/w/Install_CM_for_jordan"). So bootmenu 0.61 is installed.
*And now the phone always reboots into bootmenu 0.61; recovery cannot be accessed ("recovery.sh not found"); CM10 does not boot.
So the phone is (probably soft) bricked.
At this point, after reading different posts, the only solution I have in mind is to flash a stock sbf file. However, since most of my previous actions have resulted in worse and worse situation, I am not sure this is the best solution.
What would you advise?
Thank you,
Colinou
EDIT: after reading different posts, finally flashed stock rom with sbf file following tutorial in forums. No problem encountered, apart from starting over everything.
EDIT2: I now realise that the reason for always booting to bootmenu, was that bootmenu 0.61 was set to always boot to bootmenu! There is an option in the bootmenu to start phone to "default" instead of "bootmenu". Anyway, the recovery was still broken, so I needed to flash a SBF file anyway.

Help with SBF
ColinouRussie said:
Greetings,
Quick history of the problem:
*I have a Defy, with stock rom, rooted, and TWRP 2.1. I have a full android backup with TWRP.
*I flash CM9-NIGHTLY-120716-Defy.zip. I reboot, everything is fine.
*I reboot into new CWM recovery, make another android backup with CWM.
*I install TWRP 2.1 again.
*I flash CM10-20120924-NIGHTLY-mb525.zip.
*But then, I immediately flash again TWRP 2.1 (I think that was a mistake).
*I reboot, CM10 works fine.
*But when trying to boot into recovery from (new) bootmenu, TWRP immediately crashes and phone reboots I have no recovery mode available.
*At this time, phone still boots into CM10 just fine.
*I spend many hours trying to find how to flash a proper recovery, but to no avail. In desperation, I then follow the same recovery install procedure I followed many time ago after rooting the phone (see for example "wiki.cyanogenmod.org/w/Install_CM_for_jordan"). So bootmenu 0.61 is installed.
*And now the phone always reboots into bootmenu 0.61; recovery cannot be accessed ("recovery.sh not found"); CM10 does not boot.
So the phone is (probably soft) bricked.
At this point, after reading different posts, the only solution I have in mind is to flash a stock sbf file. However, since most of my previous actions have resulted in worse and worse situation, I am not sure this is the best solution.
What would you advise?
Thank you,
Colinou
EDIT: after reading different posts, finally flashed stock rom with sbf file following tutorial in forums. No problem encountered, apart from starting over everything.
EDIT2: I now realise that the reason for always booting to bootmenu, was that bootmenu 0.61 was set to always boot to bootmenu! There is an option in the bootmenu to start phone to "default" instead of "bootmenu". Anyway, the recovery was still broken, so I needed to flash a SBF file anyway.
Click to expand...
Click to collapse
Hi, can you please send a link for SBF, because I am having hard time searching.It seams that default link for SBF-s doesent work.
Thanks

Matija28 said:
Hi, can you please send a link for SBF, because I am having hard time searching.It seams that default link for SBF-s doesent work.
Thanks
Click to expand...
Click to collapse
Hi, Can you send me how to add twrp to stock sbf like which file will work from Motorola recovery menu or any apk ?

Hello,
Could you help me? The site sbf.droid-developers.org is offline. I need any retail sbf file to unbrick my defy mb526. Does anyone have a mirror for a stock rom of this device?

gabrielms26 said:
Hello,
Could you help me? The site sbf.droid-developers.org is offline. I need any retail sbf file to unbrick my defy mb526. Does anyone have a mirror for a stock rom of this device?
Click to expand...
Click to collapse
There is a link on quarx page,i used this to unbrick & root mine,if it helps ,i cannot post links so find it own.

Hai,
I don't remember where I downloaded the stock sbf file from, most likely from sbf.droid-developers.org, which is down now
However I kept a copy of the sbf file on my computer , it is a french retail version (but langage can be changed later), in case of desperate need, I can post it somewhere.
Nr

ColinouRussie said:
Hai,
I don't remember where I downloaded the stock sbf file from, most likely from sbf.droid-developers.org, which is down now
However I kept a copy of the sbf file on my computer , it is a french retail version (but langage can be changed later), in case of desperate need, I can post it somewhere.
Nr
Click to expand...
Click to collapse
I'm in need of an sbf file. I have a tmobile us defy will this work with it? my phone is in a bootloop. I searched high and low in this forum and on the internet all the links point to sbf.droid-developers.org or multiupload both are down. If anyone has any sbf files please upload them. thanks in advance.

axel2230 said:
I'm in need of an sbf file. I have a tmobile us defy will this work with it? my phone is in a bootloop. I searched high and low in this forum and on the internet all the links point to sbf.droid-developers.org or multiupload both are down. If anyone has any sbf files please upload them. thanks in advance.
Click to expand...
Click to collapse
I will send you a link by private message. I don't know if it will work with Tmobile, but at least you can boot your phone and flash another rom afterwards. At start it will ask you to login to motoblur, just cancel the requests, change language to english, and you're set.
Nr

defy stuck on CMR
hi guys i defy was stuck on boot it keeps on showing motorola logo then i think there is a problem i think i did a mistake that i nstalled Cynogen 7 and after using it for some time i again installed a back up from miui rom there i did a mistake and when iam on the recovery menu i cant select any option touchscreen is not working..pls help me guys

Related

[Q] Another noob with a slightly bricked Defy

Hi all, :
Ive owned a defy since january, and after a lot of lurking here decided to take the plunge and have a play with it.
It was a stock unbranded uk defy with 2.51 blur rom, it rooted no problem with super one click, i then installed thi version of recovery : http://forum.xda-developers.com/showthread.php?t=875233
I then botted it into recovey and am now stuck in a bootloop.
I can access stock recovery (vol down and power) then touch bottom right of screen. I wiped cache and user data from here.
I can enter bootloader (vol up and power) and rsd lite can detect the phone.
My question is what is the easiest way to bring my phone back to life ? Im not sure if i need to flash sbf or rom.
Not to fussed about having the latest roms or mods, just a working phone before the battery gives out.
Thanks in advance, Sam
This happened to me a few days ago the way you should do it is download the 2.51 uk sbf file and flash it over using rsd lite and it should boot straight back Into the operating system and by the way how come that version did that to your phone I've installed recovery on 2 defys and they both worked
One more question did it boot up into recovery or not ?
No it didnt boot into recovery, just the boot loop. Any idea where i can get the uk sbf ? the link here seems to be dead
So you installed system recovery and then once again in the program installed it and then you clicked boot into recovery right ?
http://and-developers.com/sbf:defy
This website has all the sbfs your one should be the second on the list
RSD lite that one into your phone and it should be good to go
so.. is the usb debugging on?
when tap install recovery button, you should turn off usb debugging.
memz180 said:
So you installed system recovery and then once again in the program installed it and then you clicked boot into recovery right ?
http://and-developers.com/sbf:defy
This website has all the sbfs your one should be the second on the list
RSD lite that one into your phone and it should be good to go
Click to expand...
Click to collapse
mannn you save my life, i was looking for a stock rom from Latin America, and i got it from that link.
Thanks for the link memz180. Downloaded sbf and flashed sbf and phone is now working. Next question is what is the idiot proof way to install recovery ?
You installed the correct recovery just make sure you click into the program and install the system recovery within the program and then click on boot to recovery make sure i would make sure superuser is allowing it so check that out to and also as stated above turn off your debugging in development and then click on recovery see if it works.
Goodluck
Rerooted phone and reinstalled recovery, no problems this time. Thanks all for your help.
Sam
No problem here at xda we do our best to help our fellow android mates lol
Another Noob with an almost bricked Defy!
sammitch said:
Hi all, :
Ive owned a defy since january, and after a lot of lurking here decided to take the plunge and have a play with it.
It was a stock unbranded uk defy with 2.51 blur rom, it rooted no problem with super one click, i then installed thi version of recovery : http://forum.xda-developers.com/showthread.php?t=875233
I then botted it into recovey and am now stuck in a bootloop.
I can access stock recovery (vol down and power) then touch bottom right of screen. I wiped cache and user data from here.
I can enter bootloader (vol up and power) and rsd lite can detect the phone.
My question is what is the easiest way to bring my phone back to life ? Im not sure if i need to flash sbf or rom.
Not to fussed about having the latest roms or mods, just a working phone before the battery gives out.
Thanks in advance, Sam
Click to expand...
Click to collapse
I have the same problem on my T-mobile US branded Defy + when I try to flash the sbf file, on RSDlite It gives me this error
"Failed flashing process. Failed flashing process. Error processing flash file. (0x700F); phone conected"
What am I doing wrong? I tried RSDlite ver 4.9 and 5.0 to no avail! Please help! Thank you!
SOLVED!
NrikeCalderon said:
I have the same problem on my T-mobile US branded Defy + when I try to flash the sbf file, on RSDlite It gives me this error
"Failed flashing process. Failed flashing process. Error processing flash file. (0x700F); phone conected"
What am I doing wrong? I tried RSDlite ver 4.9 and 5.0 to no avail! Please help! Thank you!
Click to expand...
Click to collapse
So, I was using my laptop with W7 to flash my Defy, I tried RSD lite 4.9 and 5.0 and kept getting the error message. I decided to give my desktop with Vista a shot and installed RSD lite 4.9 and the motorola drivers; i don't know why but immediately after plugging the phone in it started flashing! Awesome! After that I rooted again and installed 2ndInit (Wich is awesome!).
I backed up and flashed CM7 from the custom recovery mode. Everything started working excellent until I decided to re install 2ndInit!!! BIG MISTAKE! Never do that! I nearly bricked my phone again and couldn't load into recovery mode anymore! I had to re flash JRDNEM_U3_2.51.1. After that I had to repeat the whole process with the exemption of reinstalling 2ndInit after CM7.
Since 2ndinit is already installed you don't need to re install even if you don't have the app in your tray.
I'm in the same boat, my phone is in a reboot loop, and I can't seem to flash it...
RSD Lite 4.9 on win7
Error:
Failed flashing process. Failed flashing process. Unable to retrieve initialization values from INI file. (0x7029); phone connected
/me bangs head against the wall...
read somewhere else it has to do with where RSD Lite is installed, on my win 7 32bit that was c:\Program Files\Motorola\RSD Lite...
uninstalled, reinstalled in c:\Motorola\RSD Lite and copied the sbf to that dir too... seems to be working... hope this helps someone else!
NrikeCalderon said:
So, I was using my laptop with W7 to flash my Defy, I tried RSD lite 4.9 and 5.0 and kept getting the error message. I decided to give my desktop with Vista a shot and installed RSD lite 4.9 and the motorola drivers; i don't know why but immediately after plugging the phone in it started flashing! Awesome! After that I rooted again and installed 2ndInit (Wich is awesome!).
I backed up and flashed CM7 from the custom recovery mode. Everything started working excellent until I decided to re install 2ndInit!!! BIG MISTAKE! Never do that! I nearly bricked my phone again and couldn't load into recovery mode anymore! I had to re flash JRDNEM_U3_2.51.1. After that I had to repeat the whole process with the exemption of reinstalling 2ndInit after CM7.
Since 2ndinit is already installed you don't need to re install even if you don't have the app in your tray.
Click to expand...
Click to collapse
Yer cm7 comes with it pre installed it would flash blue at bootup you should of seen it I think on the installation instruction it's written dont install 2ndinit
just rename the .sbf file to smaller name and try again

Bootloop after UnBrick

Hello,
I try to Unbrick my A500 with Acer_A500_0.000.00_1.122.01_EMEA_GEN5_update.zip.
At the first time it works, I can boot and I want to flash the system.ing and boot.img for Acer_A500_1.141.07_COM_GEN1 with the Acer ROM Flasher to get german language support.
The HowTo in den Android-hilfe tells my that I will get an error after reboot (right) and than I have to flash another update (can´t post link because I´m a noobie)
Now I´m stick in a bootloaderloop (android logo) and nothing will help.
I try flash the unbrick update again, but the only thing I get is the Bootloop at the android logo.
I need some serious help for this.
Thanks guys
triebstahl
Doesn't sound like your getting into recovery with the update.zip. make sure you keep holding down the vol- button until you see the little green man. Don't let go of it when you see the big "Acer".
After doing the update.zip to unbrick, run itsmagice BEFORE running Acer Rom Flasher. Then flash the boot and system images from that thread. Then reboot after the 6 minute window. It should boot normally.
Or just stick to the instructions in the other thread... I think your just not getting into recovery correctly.
PS.. Acer Rom Flasher is going to get an update when I get the chance.
triebstahl said:
Hello,
Now I´m stick in a bootloaderloop (android logo) and nothing will help.
Click to expand...
Click to collapse
Have you already tried to wipe your device?
sc2k said:
Have you already tried to wipe your device?
Click to expand...
Click to collapse
this seems to be the solution. Thanks for your [TIP]
Well now I´m chinese, but I try the Acer_A500_0.000.00_1.122.01_EMEA_GEN5_update now.
Edit: It does work. Now I try the boot.img and system.img.
i had same problem
I had the same problem with that zip. It was corrupted. Found an other source update.acer.zip and it worked, but some chinese apps came with it. List few other thing. The update.acer.zip would hot boot. The zip had folder with an other update.acer.zip in it. After extracting the zip from the zip it worked.
triebstahl said:
Hello,
I try to Unbrick my A500 with Acer_A500_0.000.00_1.122.01_EMEA_GEN5_update.zip.
At the first time it works, I can boot and I want to flash the system.ing and boot.img for Acer_A500_1.141.07_COM_GEN1 with the Acer ROM Flasher to get german language support.
The HowTo in den Android-hilfe tells my that I will get an error after reboot (right) and than I have to flash another update (can´t post link because I´m a noobie)
Now I´m stick in a bootloaderloop (android logo) and nothing will help.
I try flash the unbrick update again, but the only thing I get is the Bootloop at the android logo.
I need some serious help for this.
Thanks guys
triebstahl
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1132760 try this

Help me,, Cannot boot in to recovery

Please help needed!!
I'm stuck here for 3 days
Ok I'm going to tell everything I did,,
My Gionee E7 is indian version.
First I rooted my phone with kingo Root.
Than I flashed CWM chinese version.
I upgraded my system to kitkat and changed the recovery to stock.
I used it for a week than some how my music player and gallery were corrupted.
I don't have any rom so I download one but it was in chinese, flashed it to my gionee. than after rooting,,
I flashed the CWM, same I flashed weeks ago
Here my problem started :crying:
The CWM is not starting. I used recoery tool to boot into recovery after boot up it shows black screen. I used every method holding Vol+ and power button but the same result.
than I tired to get back to my stock recovery but it does the same.
flashed many times both recoveries but didn't worked.
I searched a lot and find a TWRP. I flashed it and wow it worked Finally I can boot into recoery mode.
Now I find the Nandroid backup of indian version. I made it a zip and flashed it through twrp.
My phone is back to indian version but its slow, not too much but its slow; camera, gallery and other apps take some time to open. I can't make or rcv phone calls. Now what i did is download the update form System update.
Now i got kitkat rom.zip but twrp failed to install it.
Some one on the internet was saying that its the problem with my Kernel. I have the latest kernel so CWM won't work cuz it uses old kernel and display drivers.
My
android version is 4.2.2
Kernel version is 3.4.0-svn2155
I also got TWRP for lolipop,
and I patched binary_update in my kitkat rom too but TWRP can't flash it
Thats my whooooolllleeeee story. "
I got stuck with this for almost 3 days now I'm damn tired can't do it anymore plz help :crying::crying::crying:
I figured it out by myself
Ok guyz didn't get any help so I figured it out by my self.
I'm posting it here so if anyone gets stuck like me could solve his issue
I used GNQC Download tool and flashed the whole firmware of my cell including, kernel, rom, recovery, boot everything.
Now I'm back to stock indian rom (jellybean) with stock recovery and now I'm going to upgrade to kitkat
I'm new user so I can't posts links just replace the (dot) in the link,
First download stock firmware of Gionee e7 in following link, GNQC download tool and drivers also included in this zip:
www(dot)androidxda.com/download-gionee-stock-rom-models
Just unzip it and follow the instructions on this site:
www(dot)androidxda.com/gnqc-downlod-tool
I didn't slept last night bcuz of this mess now going to sleep whole day :silly:
Goodnite and bless you all :angel:
AkashX4686 said:
Ok guyz didn't get any help so I figured it out by my self.
I'm posting it here so if anyone gets stuck like me could solve his issue
I used GNQC Download tool and flashed the whole firmware of my cell including, kernel, rom, recovery, boot everything.
Now I'm back to stock indian rom (jellybean) with stock recovery and now I'm going to upgrade to kitkat
I'm new user so I can't posts links just replace the (dot) in the link,
First download stock firmware of Gionee e7 in following link, GNQC download tool and drivers also included in this zip:
www(dot)androidxda.com/download-gionee-stock-rom-models
Just unzip it and follow the instructions on this site:
www(dot)androidxda.com/gnqc-downlod-tool
I didn't slept last night bcuz of this mess now going to sleep whole day :silly:
Goodnite and bless you all :angel:
Click to expand...
Click to collapse
Hello my friend, please help me.
I am trying to flash stock inidan rom 4.2 but.. I installed all CWM for E7 found on the internet and I am getting black screen. I managed to Install TWRP but TWRP cannot flash the rom that I need to flash. I flashed a chinese 4.2 but is piece of garbage..
gngc-download-tool said that the com port is closed.
I have windows 64 is this the problem causing gngc not working?
No its not, it is working on 64bit windows very well.
In TWRP factory reset and format system and data, than install
Chinese 4.2 ROM. After that boot it and try it again.
It should work!
bllkarv said:
Hello my friend, please help me.
I am trying to flash stock inidan rom 4.2 but.. I installed all CWM for E7 found on the internet and I am getting black screen. I managed to Install TWRP but TWRP cannot flash the rom that I need to flash. I flashed a chinese 4.2 but is piece of garbage..
gngc-download-tool said that the com port is closed.
I have windows 64 is this the problem causing gngc not working?
Click to expand...
Click to collapse
For me...problem!
there´s a cwm recovery that flashes over the kernel...
i flashed it and than i was unable to go to recovery, every time i tried the phone power off
Solution: Flash the stock boot.img
Use the file according to the Android version...
Help
I just rooted my gionee elife e7. Flashed the chinese recovery which seemed to be the only one which would be compatible. But, while changing a few setting using pimp my rom, the software just stopped working. Errors keep showing up on the screen - "system.ui is not working", "android app is not working", I cannot even go the settings because "settings is not working". Third party apps still seem to work, so, whatsap and stuff continue to function. Doing a factory reset or flashing firmware again seem to be the only viable option.
But, when I try to load up the bootloader using the power and volume keys, it gets stuck on the screen showing the gionee logo and it reads 'fastboot mode' in the bottom left hand side corner. So,
a. can you offer any advice which may be useful ?
b. can you share the link from where you got a TWRP recovery which will work on the Elife ?
c. do you have any idea what exactly went wrong here ?
Any help you can provide will be appreciated because, it's my mausi's phone and I will have a very tough time explaining what really went down here.
Regards,

Lg g2 no os at all

Hi!
First I tell you how I recently messed up my LG G2 D802.
I hadn't had a custom rom for ages and now I wanted to have one (This wasn't the first time. I've done this a lot earlier). I had always had root access, but not custom recovery. So the first thing was to install one and I chose to download Rom Manager from Google Play, and then install ClockWorkMod. So, when I was installing the custom recovery I came up with a problem: something went wrong during the installation (I have no idea why). When I booted the device, white letters and numbers appeared on the top left of the screen, saying something like: "boot certification error" and numbers like "[780] [800]" and so on. The screen went black and the phone didn't load the OS. So I was shocked of course because I had never had such a problem.
So, desperate for trying everything to find the solution, I tried tens of ways to try to fix the problem. Finally I read about thing called SRKTool. So I used it and ended up having TWRP on my device, and no OS at all. I tried to flash CM12 and CM12.1 (downloaded from the official site) but nothing works out. TWRP says that flashing the ROM is succesful but when rebooting the system it doesn't load the OS but it comes back to TWRP Recovery mode - WHATEVER I DO. I can't enter the Download -mode at all. I tried hard reseting (Power + Vol - keys), but once again it boots to the TWRP. I can't understand why the TWRP fails to flash the ROM even though it's saying the process was successful. Or maybe this problem is much more internal - and permanent.
After tens of XDA developers' threads I'm writing this here because I'm in need of help. I want to bring my G2 to back in life. I'm out of ideas. Can you help me? I tried to flash the stock firmware but guess what happened? The installation failed, and the device booted back to TWRP. So all I'm able to do is to use the TWRP Recovery. I appreciate your help. Thank you.
(Ps. I'm sorry if I break the rules by writing a new thread. My problem just seems to be so unique that I couldn't find help anywhere.)
If you have access to twrp than you can do what ever is needed
what twrp version douy you have?
enabel MTP, so you can copy from PC
Spumpkin said:
Hi!
First I tell you how I recently messed up my LG G2 D802.
I hadn't had a custom rom for ages and now I wanted to have one (This wasn't the first time. I've done this a lot earlier). I had always had root access, but not custom recovery. So the first thing was to install one and I chose to download Rom Manager from Google Play, and then install ClockWorkMod. So, when I was installing the custom recovery I came up with a problem: something went wrong during the installation (I have no idea why). When I booted the device, white letters and numbers appeared on the top left of the screen, saying something like: "boot certification error" and numbers like "[780] [800]" and so on. The screen went black and the phone didn't load the OS. So I was shocked of course because I had never had such a problem.
So, desperate for trying everything to find the solution, I tried tens of ways to try to fix the problem. Finally I read about thing called SRKTool. So I used it and ended up having TWRP on my device, and no OS at all. I tried to flash CM12 and CM12.1 (downloaded from the official site) but nothing works out. TWRP says that flashing the ROM is succesful but when rebooting the system it doesn't load the OS but it comes back to TWRP Recovery mode - WHATEVER I DO. I can't enter the Download -mode at all. I tried hard reseting (Power + Vol - keys), but once again it boots to the TWRP. I can't understand why the TWRP fails to flash the ROM even though it's saying the process was successful. Or maybe this problem is much more internal - and permanent.
After tens of XDA developers' threads I'm writing this here because I'm in need of help. I want to bring my G2 to back in life. I'm out of ideas. Can you help me? I tried to flash the stock firmware but guess what happened? The installation failed, and the device booted back to TWRP. So all I'm able to do is to use the TWRP Recovery. I appreciate your help. Thank you.
(Ps. I'm sorry if I break the rules by writing a new thread. My problem just seems to be so unique that I couldn't find help anywhere.)
Click to expand...
Click to collapse
The solution is easy. Download the stock rom for your model and install it with otg cable. The reason cm12 is not booted is because you need jb bootloader or caf bootstacks.
Enviado desde mi LG-D802 mediante Tapatalk
renzo090513 said:
The solution is easy. Download the stock rom for your model and install it with otg cable. The reason cm12 is not booted is because you need jb bootloader or caf bootstacks.
Enviado desde mi LG-D802 mediante Tapatalk
Click to expand...
Click to collapse
cm11 => jb bootloader
cm12, cm12.1 and cm13 => kk bootloader
klemenSLO said:
If you have access to twrp than you can do what ever is needed
what twrp version douy you have?
enabel MTP, so you can copy from PC
Click to expand...
Click to collapse
The current version is 2.8.7.3. Should I try other versions?
Did you solve the issue? Or is it still not allowing you to get into your F/W?
staylecrate said:
Did you solve the issue? Or is it still not allowing you to get into your F/W?
Click to expand...
Click to collapse
Hi!
I tried to install TWRP version 2.6.6.3, but it fails to flash it so I'm stuck with the version 2.8.7.3. All I'm able to enter is just the recovery mode. I can't enter the download mode so I can't flash the stock firmware.
Currently I'm out of ideas. I can't flash any OS, the TWRP fails everytime and creates errors.
Try flash bumped kernel like lp dorimanx then flash bumped bootstak then lp rom like cloudy or stock. Or google this: lg g2 unbrickable now xda ...that work for me

Help Recovering Please

I eventually decided to flash Kitkat onto my Defy+.
Followed this guide here:-
http://forum.xda-developers.com/showthread.php?p=52342403#post52342403
Everything worked fine until I got to the actual flashing of the KK Rom. TWRP had loaded fine but insisted I had no OS installed and on exit suggested device was not rooted?
Phone kept saying failed and to re partition. So I tried the Resize.zip from another guide. This did nothing either , still the same.
It had also had the following error, "Error Executing Updater Binary In Zip".
So I tried the solution here:-
https://kalitutorials.wordpress.com/2015/06/19/solve-error-executing-updater-binary-in-zip/
Now I cannot boot into TWRP or Clockworkmod recovery. When I try to boot phone it just sits on Motorola Sign but doesn't progress and no led flashes to enter TWRP. Battery needs to be removed to switch off.
If I power up with Volume down pressed, I get picture of Android Green Robot standing up with an yellow exclamation in a white lined triangle. No options are shown.
Pressing Vol up and down I get me to Android System Recovery <3e>. Options there are, reboot system now, apply update from sdcard, wipe data/factory reset, wipe cache partition.
I can also enter bootloader using vol up and power.
Any ideas anyone, found this guide to try to fix but don't want to try anything else without some confidence it will work.
http://www.tech-zealots.com/tutorials/unbrick-motorola-defy-or-defy-100-working/
I have a nandroid backup created in normal recovery btw. I would prefer to flash back to it if possible.
Thanks
G
You need to download a sbf file https://mega.nz/#!915TCAAD!X7_f1t83lVPkK5p7jUdokeE4SQ8qTRqPnBWNvfgyxWA (this one is stock android 2.3.6), then you need to install drivers and rsd lite and connect your phone (must be already in bootloader mode) to your pc and then reflash the sbf file. After that, your phone will boot up to the stock firmware and you can install cm11 then. Basically you can follow up the the guide that you posted. Good Luck
dc239 said:
You need to download a sbf file https://mega.nz/#!915TCAAD!X7_f1t83lVPkK5p7jUdokeE4SQ8qTRqPnBWNvfgyxWA (this one is stock android 2.3.6), then you need to install drivers and rsd lite and connect your phone (must be already in bootloader mode) to your pc and then reflash the sbf file. After that, your phone will boot up to the stock firmware and you can install cm11 then. Basically you can follow up the the guide that you posted. Good Luck
Click to expand...
Click to collapse
Thanks for your reply.
Tried what you suggested but after flashing that sbf the phone tries to boot up but after logo drops back to bootloader 9.10 with ERR:a5,69,35,00,27 .
I managed to get the Retail UK sbf referred to here:-
http://forum.xda-developers.com/showthread.php?t=1421526
Tried flashing it but end up with a black screen bootloader and just white led lit. Reflashed the sbf u suggested and back to Bootloader with Err.
Googling seems to suggest I am just needing to get the right sbf for the phone.
I have the Nandroid backup made with Clockworkmod recovery. Is there anyway to flash it?
TIA
G
Sorted
After extensive digging and climbing the steep learning curve. Decided the problem was that the sbf file u suggested was DFP 231 and possibly my phone was DFP 2311. Found Firmwares here:-
https://firmware.center/firmware/Motorola/Defy+ (MB526)/Stock/
And downloaded the DPF 2311 Rom, only was one. (DEFYPLUS_U3_4.5.1-134_DFP-2311_BLUR_SIGN_USADEFYEMARAB1B8TFDE004.0R_PDS03C_USAJRDNGIBRO2DE_P020_A025_M002_Service1FF.sbf). Tried flashing it and voila system is back, albeit it started up in German.
Gonna try the rooting mehod here:-
http://forum.xda-developers.com/showthread.php?t=1820282
For anyone elses benefit, the links for Roms at Android Developers don't work. The retail EU Firmware mentioned in the rootong guide is available on the site referred to above. U can tell when you click the link to the Android Developers site as the browser URL shows the full file name as follows.
DEFYPLUS_U3_4.5.1-134_DFP-231_GR_SIGN_UCADEFYEMARAB1B80AA004.0R_PDS03C_USAJRDNGIBRRTCEE_P022_A022_Service1FF.sbf.gz
The rooted one I think is the same one you linked me to and is still valid in the Rooting guide too.
Thanks for all help and I hope this is of use to someone else.
G
Minor question still remains.
If I am trying to install Kitkat rom. DO I still need to Root phone if the rooted 231 has been installed, I presume not?
G
Followed rooting guide and so now have a rooted 231. All good
Now for KK.
G

Categories

Resources