Database Users

[Q] unrevoked 3.21 on wildfire and power on problems

hello,
I used unrevoked 3.21 on my italian wildfire (nobrand) with the htc update 1.25.405.1...
After rooting, without new ROMs but with the default one, I have problems when wildfire is powered off...
Even if the battery is full, if I connect it to the power switch, the LED switch on to RED and doesn't became GREEN.
AND I cannot power on the cell (with or without power cord connected)!
I have to remove battery to power on!
IS there a solution?
thank you.

The problem is known and I think there is still no solution. It seems it's the fault of unrevoked.
Sent from my HTC Wildfire using XDA App

it is a unsolved problem with unrevoked, Charging the phone while it is off will make it unable to start it unless you remove and reinsert the battery.
BTW i have a fix for it(kind off): DO NOT CHARGE THE PHONE WHILE IT IS OFF

CrimzonEyed said:
it is a unsolved problem with unrevoked, Charging the phone while it is off will make it unable to start it unless you remove and reinsert the battery.
BTW i have a fix for it(kind off): DO NOT CHARGE THE PHONE WHILE IT IS OFF
Click to expand...
Click to collapse
ahaha good fix
however , when it is off, it is realy charging or not?
there can be any problems with battery? overcharge for example?

however, in this forum, I have read (and I cannot find it anymore... ) that the problem is clockwork recovery and someone suggested to install the original recovery to fix it.
Is it really possible? doing this, can I keep su/root mode?
thank you

I think there is another problem rooting wildfire with unrevoked; sometime (after some minutes my cell is in stand-by mode) switching on the display I cannot see the WIFI icon on the notify bar (as if it was disconnected).
Some seconds after, the icon come back

girello71 said:
ahaha good fix
however , when it is off, it is realy charging or not?
there can be any problems with battery? overcharge for example?
Click to expand...
Click to collapse
Have been able to charge untill green while the phone is off with the unrevoked, after that i unpluged the charger, removed/reinserted the battery. And started up.
Have never heard that unrevoked have caused overcharge.

girello71 said:
hello,
I used unrevoked 3.21 on my italian wildfire (nobrand) with the htc update 1.25.405.1...
After rooting, without new ROMs but with the default one, I have problems when wildfire is powered off...
Even if the battery is full, if I connect it to the power switch, the LED switch on to RED and doesn't became GREEN.
AND I cannot power on the cell (with or without power cord connected)!
I have to remove battery to power on!
IS there a solution?
thank you.
Click to expand...
Click to collapse
Ciao Girello....In base al nik e a quanto descritto sul tuo cell sei italiano.....Ho comprato il WildFire da poco e visto che Froyo non arriva avrei pensato di rootarlo.
Però ho ancora qualche dubbio e con l'inglese non sono tanto ferrato e quindi se posso chiedere a te qualke info.....A quanto ho capito leggendo in giro nella rete l'operazione di rooting fà decadere la garanzia, ma se eseguo questa operazione e poi decido di tornare al firmware originale, la garanzia secondo te è ancora "operativa"? Nel caso decida di tornare indietro qual'è la ROM giusta per il "nostro" cell? Ultimissima domanda....Come ti trovi col cell dopo averlo rootato...Cosa c'è in più o in meno?
Grazie Ciao

girello71 said:
hello,
I used unrevoked 3.21 on my italian wildfire (nobrand) with the htc update 1.25.405.1...
After rooting, without new ROMs but with the default one, I have problems when wildfire is powered off...
Even if the battery is full, if I connect it to the power switch, the LED switch on to RED and doesn't became GREEN.
AND I cannot power on the cell (with or without power cord connected)!
I have to remove battery to power on!
IS there a solution?
thank you.
Click to expand...
Click to collapse
hi....
again, is there any solutions for this issue ?
i downloaded a rom from shipped.com and tried to reflash it, but the process always stucked in the middle.

Yeah this bug is annoying. I have been considering using an RUU to unroot because of this problem. I hope someone works out a fix for it.

Hpez said:
Yeah this bug is annoying. I have been considering using an RUU to unroot because of this problem. I hope someone works out a fix for it.
Click to expand...
Click to collapse
Did you succeed to unroot your WF ?
I tried to reflash using Asian RUU but the process stopped in the middle, and said something like I should get a suitable ROM.
Rgds,
Andika

Hi guys, i have the same power on issue, there is a way to contact or inform the developer's team to fix this bug?
Ciao ragazzi, anche io ho questo fastidioso problema dell'accensione, c'è un modo per mettersi in contatto con il team di sviluppo di unrevoked per informarli del bug, e per poterlo quindi correggere?

Hello,to eliminate this problem you can remove unrevoked?
I tried to flash my wildfire with Froyo but unrevoked is always installed, with this problem of red light ...

[Q] how root wildfire htccn chs2.10.1400.3 foryo 2.2

Professionals should try to phone a friend wildfire htccn chs2.10.1400.3 foryo 2.2 the root should have about 2 months now that I'm looking for this program and no one has been able to implement it

Methods that have been tested and have failed
Methods that have been tested and have failed
Using programs unrEVOked
Using r1-buzz-root program that works adb
And a test file and transferred to the phone after installing the update file is root Phones
Application SuperOneClickv1.5.4-ShortFuse
Or file transfer recovery-clockwork-2.5.0.1-buzz and its conversion to update.zip file after turning off the phone and then went to bootloder part of recovery but this was not the answer
And several other solutions that unfortunately none of them led to my phone not being root
Which is why I am overwhelmed and I ask you help on this matter I hope someone can help me to

How many times must people ask this? There is still currently no way to root the chinese froyo you just simply have to wait for unrevoked to release a new version. I'm just wondering why you guys upgraded to this without reading and searching first

For information
The posts to this for the friends who've specialized in terms of Nrf hacked phone software and operating system are professional action to release new software and put it in this post should

a2soleimani said:
The posts to this for the friends who've specialized in terms of Nrf hacked phone software and operating system are professional action to release new software and put it in this post should
Click to expand...
Click to collapse
erm... what?

i'll just say this again, NO YOU CANNOT ROOT IT YET. big deal it's been 2 months, maybe they haven't updated it yet because 1. they're still working on it, or 2. because they don't have enough time. 3. learn to be paitient, ppl like you annoy me so badly.

Hpez said:
erm... what?
Click to expand...
Click to collapse
I just thought the same.

try this one:
http://forum.xda-developers.com/showthread.php?t=833953
should work with your rom, if not: leave note to developper

Zorkman said:
try this one:
http://forum.xda-developers.com/showthread.php?t=833953
should work with your rom, if not: leave note to developper
Click to expand...
Click to collapse
Have you tested this solution is that it works? thank you

Confirmed working by this method..
http://forum.xda-developers.com/showthread.php?t=833953

double_ofour said:
Confirmed working by this method..
http://forum.xda-developers.com/showthread.php?t=833953
Click to expand...
Click to collapse
Confirmed working by this method with htccn chs2.10.1400.3 foryo 2.2 ??? I have big problem with this rom and my wildfire...

I'm too
The china rom have nothing to use.
Who can help me.

No working. I did try. Installed, showing completed, automatically reboot, but nothing happend

sort of working, gives root but not recovery option. root explorer can use r/w option

what can we do with softroot? and how do we know rooted? Thanks

tuanvo1982 said:
what can we do with softroot? and how do we know rooted? Thanks
Click to expand...
Click to collapse
mostly nothing, run progs what need root i guess

solution hboot 0.83 to 0.80 de froyo chino
z4root luego rom manager luego com.speedsoftware.rootexplorer.v.2.12.3.apk
en rootexplorer entrar y dar r/w en los archivos no se en cual seguro que lo hecho sin saber que functiona pero bueno.luego copiar pc49img en la raiz de la tarjeta de memoria (tarjeta sera de oro) rebot in hboot mode y a mi a functionado

donot work
I do not think you z4root program to work because the new version of the program it was announced that 1.2.1 that is used for non-Wildfire

z4root 1.2.0 solo hace roor no da opcion de recovery pero seguir con rot manager in final accepta recovery con inagen original pc 49img.zip en la raiz sd

ionel_lili said:
z4root 1.2.0 solo hace roor no da opcion de recovery pero seguir con rot manager in final accepta recovery con inagen original pc 49img.zip en la raiz sd
Click to expand...
Click to collapse
this is an english forum, english please

My sgs2 drops 3g - hsdpa connection randomly

Hi , im suffering one big problem... My phone suddenly disconnects from the 3g or hsdpa signal at the point that Im not able to receive or make phone calls , to resolve that I need to go to airplane mode or wait 2 -3 minutes . Its not an operator problem becuase I had the exact same settings (apn) with my captivate and I never faced that.
Ive tried many roms , many modems , and even disable Fast dormancy without no luck.
So , is anyone suffering the same problem? , is there any way to fix it!
thanks!

Use Search tool :
http://forum.xda-developers.com/showthread.php?t=1132399
http://forum.xda-developers.com/showthread.php?t=1097612

Ugh........................

same trouble for me

Because everyone that's posting is from the far corners of the world, there's no stock answer to radio issues. Some of the problems have been carrier specific and even down to a certain city on that carrier.
1) The phone's designed to drop from "H" to "3G" when data's not in use to save battery. When working properly it picks back up immediately when needed.
2) By default, "fast dormancy" is enabled on the phone. It too is to save battery and works well on carriers that support it. Not so well on carriers that don't.
Dig around on the forum and you'll find tons of discussion on every flavor of radio issue.

I was able to get rid of that problem by wiping data/restoring stock settings and then NOT installing any configs from the configuration messages my operator sent me.
Ain't had any problems since. 3G/H+ working perfectly.

Ive tried many methods , many roms , many modems , tweaks... And had NO luck ... I just can say its not a network issue , or a software , I think its the phone itself because my old cappy always worked great!
Im going to exchange it! , thats seems to be the only solution...

BarryH_GEG said:
Because everyone that's posting is from the far corners of the world, there's no stock answer to radio issues. Some of the problems have been carrier specific and even down to a certain city on that carrier.
1) The phone's designed to drop from "H" to "3G" when data's not in use to save battery. When working properly it picks back up immediately when needed.
2) By default, "fast dormancy" is enabled on the phone. It too is to save battery and works well on carriers that support it. Not so well on carriers that don't.
Dig around on the forum and you'll find tons of discussion on every flavor of radio issue.
Click to expand...
Click to collapse
That is fine, if you want it that way. But it should be an option -- I want to turn it off as it thoroughly ruins my browsing experience, but there seems to be no way of doing so. Which is annoying to say the least.

mca1490 said:
Ive tried many methods , many roms , many modems , tweaks... And had NO luck ... I just can say its not a network issue , or a software , I think its the phone itself because my old cappy always worked great!
Im going to exchange it! , thats seems to be the only solution...
Click to expand...
Click to collapse
Mae que genial!
Crei que era el unico tico en este foro. Vieras que yo tengo la misma bronca.
Lo que hice fue disable el FAst Dormancy.
Parece estar sirviendo. Igual con el ICE, no se puede hacer mucho que digamos...
Donde va a cambiar su cel? Donde lo compro que puede cambiarlo?
Salaudos desde Heredia

Hi, I´m also from Costa Rica, i had this exact same problem, signal would just drop, could not see the phone network, i thought i had a bad phone, then I disabled fast dormancy and disabled HSPA, so that only the 3G logo stayed when using mobile data. In Costa Rica the 3g speed´s are low so disabling HSPA was no problem for me. I have no problems anymore with the signal dropping.
To Disable HSPA
Go to the phone dialer pad and enter this code: *#301279#
Click [2] CHANGE HSPA REVISION
Click [1] RELEASE 99 (HSPA OFF)
I´m on stock KE2, not rooted yet
Saludos TIcos! jaja

Ok, to keep it in English.
So I need to enter that code: *#301279#
Then which of the 2 options should I press? The 2 or the 1?
I'll try this just in case disabling Fast Dormancy doesn't work.
Thanks!

You press 2 first ....then it takes you to another menu, then press option 1

does this work?

worked here

almorsol said:
Ok, to keep it in English.
So I need to enter that code: *#301279#
Then which of the 2 options should I press? The 2 or the 1?
I'll try this just in case disabling Fast Dormancy doesn't work.
Thanks!
Click to expand...
Click to collapse
jaja q nivel varios ticos de la nada xDD , maes no al chile ya trate de todo y nada! , eso de deshabilitar el hspa desde el menu no me "funco" , ya probe varios metodos y nada , incluso cambie mi sim por uno nuevo y hasta me compre un chip prepago tuyo para probar.. pero nada!! , yo el mio lo compre x Expansys , creo q manana lo voy a devolver xq di nada q ver la vara...
Ok , Tomorrow I will send my sgs2 to repair.. Im hoping to get a fully functional phone again , btw I think there are just only few phones suffering this right? , I guess its not a problem in all the sgs2 phone over all the world xD
"cheers"

Di si, mala nota.
Mine seems to be working just by disabling fast dormancy.
By the way dude. If my phone has 1 year warranty, where in Costa Rica could I take it for revision?
Thanks

almorsol said:
Di si, mala nota.
Mine seems to be working just by disabling fast dormancy.
By the way dude. If my phone has 1 year warranty, where in Costa Rica could I take it for revision?
Thanks
Click to expand...
Click to collapse
MAE!!!! al parecer la red del ice con el internet esta fallando!!!! Yo hoy en la tarde fui a dejar mi cel para enviarlo a estados!! , pero otros amigos y mi novia q tienen android dicen q se les va el internet!!! , no se que hacer!! al parecer si es un problema de red xq estoy usando mi captivate de nuevo y tambien le pasa lo mismo!!! pele el ojo..
It seems that my problem is related with the network... Me and other friends are also facing it (other android phones.. xperia x10 , cappy) !!! , Its weird becuase its the first time its happening!!

mca1490 said:
Im hoping to get a fully functional phone again , btw I think there are just only few phones suffering this right? , I guess its not a problem in all the sgs2 phone over all the world xD
"cheers"
Click to expand...
Click to collapse
No.
The problem is with all sgs2.
Some people just don't realise it.
I've got the same problem in UK.

well.. its a very annoying problem ... hopefully mine is related with my network provider.. I will test on monday..!

Those are good news for us the "Ticos" since it means there are no faulty phones. Just a crappy network.
All heil ICE!

LG E900 boot problem SOLVED

hello guys..
after almost 3 months, trying to revive my LG E900, from the boot problem, when the phone stuck on LG logo; tried everything, from cold boot, to flash firmware, and nothing...
Today i decided to try to fix the hardware by myself..
so with the thread created by wm.andrew.wilson i have successfully disassembled my phone.
well first it looks like this : main board
but when i removed the upper board and booted the phone, it worked, just with this board mounted with the hole phone...
but removing the upper board will deprive me from using a sim card, as you see, the sim card must be inserted in this board..
so after few test, i realised that the WIFI+FM receptor is the problem, shot circuit it and booted the phone, worked perfectly, so i just decided to sacrifice my WIFI+FM and try it, i removed it as you can see here . i just cut it ...
assembly the phone, and everything worked fine, just when you try yo activate the WIFI, it just keeps loading and nothing happen.. so you can use your phone normally and listen to your music, play games, download... you will ask how to download without WIFI ( wifi ship removed ) i tell you, you still can use your USB DATA CABLE with ZUNE and download everything from MARKETPLACE, even i guess the user account, you can do it with ZUNE, and if not, you can just restore your phone
well this was my try, and i do not ask you to try it, unless you are curious enough and take the risk, but i am not responsible of any damage you may cause to your phone, and be carefully this void your warranty.

Same here. removin upper board makes my phone usable again. Unfortunately not lucky as you, removing WIFI+FM receptor by cutting it didn't solve the problem.

Hi, guys! Have you seen New SIM Card Micro-HD Flex Cable for LG E900 Optimus 7 on ebay (excuse me, forum doesn't allow me to post external links)?
Is it right part?

How to fix problem
Only one way to fix boot problem is to buy New SIM Card Micro-HD Flex Cable for LG E900 Optimus 7 from ebay.com (30$) or from mobile-cherry.com (28$), disassemble phone and replace your broken board (FIX LG optimus E900 digitized, reparar cristal LG E900 on youtube.com). In my case it worked.

I confirm . worked

no hay solucion cortando
he cortado el famoso RF-SUB board de a poquitos, quitando componentes primero de uno a uno y luego recortando y resulta que aunque se quede con apenas medio centimetro de tarjeta, luego de quitar absolutamente todos los componentes, igual sigue fallando.
Creo que es un problema en la union de las capas de circuito en toda la tarjeta, en algunos casos es cerca del wifi, en otros como en mi caso es casi junto al conector, mejor dicho no sirve de nada, solo reemplazarlo.
En esa tarjeta tambien esta el touch por lo que aunque encienda no sirve de mucho porque no hay tactil.
habrá que comprar nomas.

Hello, I solved this warming the chip and capacitors over 380 deg. w/ hot air station to resolder the connections of the chip, so guess... It works now. :silly:
Edit: Now assembled it back and tested WiFi, works! hope I helped somehow...

nasko_spasko said:
Hello, I solved this warming the chip and capacitors over 380 deg. w/ hot air station to resolder the connections of the chip, so guess... It works now. :silly:
Edit: Now assembled it back and tested WiFi, works! hope I helped somehow...
Click to expand...
Click to collapse
which one did you resoldered ? the Wifi chip ?

psytr0nic said:
which one did you resoldered ? the Wifi chip ?
Click to expand...
Click to collapse
Correct! That one from the pic in post #1

itmk said:
hello guys..
after almost 3 months, trying to revive my LG E900, from the boot problem, when the phone stuck on LG logo; tried everything, from cold boot, to flash firmware, and nothing...
Today i decided to try to fix the hardware by myself..
so with the thread created by wm.andrew.wilson i have successfully disassembled my phone.
well first it looks like this : main board
but when i removed the upper board and booted the phone, it worked, just with this board mounted with the hole phone...
but removing the upper board will deprive me from using a sim card, as you see, the sim card must be inserted in this board..
so after few test, i realised that the WIFI+FM receptor is the problem, shot circuit it and booted the phone, worked perfectly, so i just decided to sacrifice my WIFI+FM and try it, i removed it as you can see here . i just cut it ...
assembly the phone, and everything worked fine, just when you try yo activate the WIFI, it just keeps loading and nothing happen.. so you can use your phone normally and listen to your music, play games, download... you will ask how to download without WIFI ( wifi ship removed ) i tell you, you still can use your USB DATA CABLE with ZUNE and download everything from MARKETPLACE, even i guess the user account, you can do it with ZUNE, and if not, you can just restore your phone
well this was my try, and i do not ask you to try it, unless you are curious enough and take the risk, but i am not responsible of any damage you may cause to your phone, and be carefully this void your warranty.
Click to expand...
Click to collapse
i just rehot above said ics

Buttons backlight ALWAYS on, Even when the phone powered off!

I've recently bricked my phone and i had to boot to EDL using test points method. I've noticed that after i did that, the buttons would ALWAYS be lit up no matter what i do. I even unplugged and battery connection and plugged it back in again and they'd still immediately turn back on. I've tried using custom roms and editing values manually using a file explorer but it'd still be constantly on no matter what I do. What's the cause of this and is it fixable?
My last resort would be to just cut off power to the LEDs on the buttons but that just seems a little bit extreme to me
Any help would be greatly appreciated

Same here
I have the same problem did you fix it?

junkynotes said:
I have the same problem did you fix it?
Click to expand...
Click to collapse
No, not yet
I haven't been able to find a solution so far.
What caused yours to happen?

berezker said:
No, not yet
I haven't been able to find a solution so far.
What caused yours to happen?
Click to expand...
Click to collapse
Dropped my phone in water! Everything else is working fine except this backlight thing!

Any luck?

Spanish
Me pasa lo mismo, se me cayó al agua... Pero no se quedaban encendidas... Pero empeze a desarmarlo para poder arreglar la pantalla, Porque estaba negra... Entonces lo desarme por completo y se quedaron encendidas... Talvez conecte algo mal..
Encontraste solución?