Hi,
I've searched the forums but haven't found a solution to my problem. I rooted my Nook Color (1.1.0) using auto-nooter 3.0. Everything worked fine, then I tried to flash to CM7 using CWM. When I subsequently rebooted, the Nook goes into a boot loop where it never gets past the "Touch the Future of...." display before it reboots.
I've can't get into ADB because the unit reboots before I can get access. Also tried booting into CWM (3.0.0.5 and 3.0.1) on an SD Card. When I do this, it shows the "loading..." display for a few seconds then reverts to the boot cycle. Also tried nooter 0.2 but same result.
Tried doing 8 successive boot cycles by trying to turn it off before it reboots, but no luck.
I've noticed that others have had boot issues also, but it seems that everyone else has been able to eventually boot back into CWM via SD card.
If anyone has any suggestions, I would definitely appreciate the help.
Thanks.
I experienced this exact problem and never did get it working. I was running Nookie Froyo on SD with overclock when it suddenly started rebooting. Doesn't matter if the card is in or out, it gets to the point you describe and reboots. All of the "restore to stock' tricks failed because it keeps rebooting, even when booting into CWM from SD. I ended up replacing it with another new NC and put the the first one in storage hoping I someday figure out the problem. I've never found anyone else with quite this problem. I'll be anxiously watching this thread!
Not sure whether I should start to panic because you never got it working, or feel relieved because I am not the only one to experience this issue
You can add another person who is having this problem.
Yesterday I asked Rom manager to boot into recovery and that was all she wrote.
The nook gets through "Touch the future of reading," then the screen flashes for a fraction of a second before repeating the process again.
Holding 'n' and power while booting also has no affect; and it seems to ignore whatever is in the SD card slot.
Got it working!
Not exactly how this worked but here is what I did.
First off I used another SD Card Reader Although the idea of using another card reader doesn't seem to make sense; I had seen it on another forum.
I also Used a new uSD card
Used Win32DiskImage to burn the image to the uSD card (had been using DD on a linux box)
The images used was the Clockwork Recovery image (2GB,) look around and you should be able to find it.
I also copied the removeclockwork.zip
This should be available with a google search as well
From there it just worked like it was supposed to. The nook booted off the micro SD card and I used the removecwr.zip
Hope this helps
Hi everyone! Please help me! I've spent most of the last 18 hours on this, rested, and have come back hoping to start today off positively.
I have a new "blue dot" nook with the new partitioning scheme. Not realizing that, I tried to install CM7 internally using a youtube video from huskermania (sorry, XDAforums will not let me link). All went fine, I assume, except for an error in Clockwork that read: Error: can't format /data" error. I believe, after researching, this is a result of the change in partitioning.
Frustrated that I had bricked my nook, and not really wanting to run an internal anyways so I can revert back to regular ROM if I want, I tried to unroot using directions from huskermania again. I really thought it had worked, but it is now stuck on the rainbow Nook Color screen, which will disappear and come back repeatedly.
Please help. My goal is to reinstall the original ROM, then try to install another using SD, but that's not my main priority right now.
HURRAY!!!!
Ok, success!!!! I cannot believe something finally worked. The 8 step reboot did not work, but using power, home, and +volume did.
I am saving the SD card I used to reboot this. Any thoughts on the best way to root a new "blue dot" nook using external so I don ever have this issue again? I know I need to change the partitioning, but I'm still not sure how, even after reading what Maurice Mongeon has to say in his post "how to repartition a blue dot nook color." Thoughts?
How exactly did you finally get it to work? I've done the exact same thing and I'm not sure what to do next. I have a refurbed NC that came with 1.2 installed and I rooted it with manualnooter and immediately flashed CM7.02 stable from CWM 3.0.2.8. It had all kinds of force close issues so I tried to restore to stock but keep getting stuck on the boot animation. I re-flashed CM7 and it still works but I still have all kinds of force close issues. When I try to format data in CWM it says can't format /data! I'm kind of at a loss right now...
UPDATE: Got it working. I had been using the wrong cwm...
Hi, folks! I'll post this question here just in case I can get more help, as I've run out of ideas, and I've read all the threads on the specified subject, but none have helped. If it's against the rules, then Mods, please delete the thread. If not, Thank you.
The Problem:
I recently upgraded to CM7.2 Mirage-KANG- from Phiremod 6.2. The Nook was running great until I tried to upgrade to the ICS/CM9 nightly from here. The Nook would refuse to boot. The only way I could get it to boot was with an old CWM sd card I'd used to root it in the first place. I figured I could fix the boot by wiping the /data, /system, and /cache files from the Nook. Bad move. That just made things worse, as now, the Nook doesn't even load from the SD Card anymore unless I hold the "n" key and hold the power button.
I tried restoring it to to stock 1.01 to possibly start from scratch, and all was well, until it was time to register it. It wouldn't let me, even while on wi-fi. It would give me an "error has occurred, Nook will now Power Off" message without weven loading or anything. Upon further inspection, I checked the properties tab by accessing the wi-fi menu and saw that the model number and unit I.D.(I think) were "unknown" and in red letters.
Presently:
Since then, I tried everything from the Autonooter to the Monster Recovery Pack and nothing works. The Nook, without the Micro SD loaded, shows the Cyanogenmod7 logo loading, then goes black, though the backlight remains on. With the card, it goes straight into CWM. It sometimes doesn't boot into anything at all.
Extra Info:
I'm using a Sandisk (4) 8 GB card for the rooting and such. I normally use the 16 GB (4) model.
So my question is:
What can I do from here? Can/should I go back to the beginning as a Stock Nook 1.0, or is there a better, wiser alternative that I can use to get the Nook booting into CM7 or higher normally?
Any help'd be greatly appreciated.
Did you try following the directions on this post http://forum.xda-developers.com/showthread.php?t=931720
Yeah, as a matter of fact, I tried the exact same directions on both those pages, and used that exact CWM 3.0.2 img file to install the Nook 1.01 file.
From there, my Nook boots up fine, gets past the "n" logo, but once in the setup, won't register because it's serial #, Model #, and Mac Address are "missing", and won't let me past the Setup Menu.
Update: I managed to flash Stock 1.0.2. to the Nook. Upon booting it up, it prevented me from registering the Nook, until I figured out the factory mode method to bypass it, and used Autonooter to root.
Now I have a dilemma: I want to ditch Stock and jump to some sort of CM7, but Stock won't allow me to reboot into CWM at all, even after having flashed it through Rom Manager or flashing it to EMMC.
I know there's a way out, I just don't see it.
Any advice would be appreciated.
Sent from my Nook Color using xda premium
I would assume you already have CWM on a SD card. Drop your chosen CM 7 zip onto the card, boot into CWM recovery, choose the zip and install. Same should work with ICS zip but you shpuld prolly avoid it until its in more stable shape.
Well, after a few weeks of reading posts, even opening up the hardware and taking the nook apart, here I am asking a question. I figure I would go to the source rather than those other place I was reading and tryign to get info from (mot os those places link here anyway). I know that everyone says that the nook is "unbrickable;" while I want to believe it, I may be in a place where it may be true.
I do want to add a thanks as well, since the NC "tablet" has been very handy, and my wife and I have really enjoyed it. Wouldn't have happened without you all. I wish I had more time to participate in developing, but working 80+ hours/week in a hospital limits my free time, as you can imagine.
I rooted the NC and installed Cyanogenmod 7 back in July 2011. It was a 1.1 model (if I recall correctly). I installed the mod to EMMC, along with CWM. Things ran fine for 6 months. Literally no issues. Then, one night the battery was dead, so I plugged it into the computer USB to charge while the machine was off. Didn't touch it at all. When I went to turn it on again, I was stuck in a bootloop. It would go to the cyanogenmod screen and say "Loading" then would start over again. So, I naturally made a bootable SD card, and tried going into CWR to fix things. However, the SD card had the bootloop as well. It would get to the two skulls and "Loading", flash blank, then start over again.
That went on for a while. I couldn't boot into anything, not into recovery, alternate images, literally nothing. So, I tried different images --- nothing. Finally, I did the power+n and got into the only screen that wouldn't keep resetting. It has blue text and says "Entering boot menu". The menu says "Encore U-boot Menu by j4mmr. 1.2 port+ extras by fattire." From this screen, I can navigate and change the boot options. However, once again, whatever I try does not actually boot, regardless of what I set it to. The only thing that I got from getting here was no more boot loops. After getting it to this point, I can try loading anything, and it will start, then the screen goes black/blank, and nothing happens. Left it on for hours to test.
Since that point, I have switched cards (SanDisk 2 GB class 4, Patriot 8 GB and a generic 8 GB microSD). I know that cards work correctly because I got a hold of a second nook, and they work fine on it. Below are a list of all the images I have tried to run off the SD. Again, nothing will boot, not even clockwork recovery/clockworkmod.
128 mb rootpack (IOMonster)
clockwork 3.0.2.8
clockwork 3.2.0.1 eyeballer
Nooter
Mirage_CM7_ICS_CM9_DualbootSD (this card works great on the working NC)
TWRP 2.0 RC0
Generic SD
Clockwork 0.7 -> starts boot loops again
I also tried ADB, connecting to the computer and using putty over SSH. Didn't work. 8 interrupted boots with 9th holding power+n. Nope. I even took the nook apart and disconnected the battery. Still no go.
If I recall, I think I had CWM 3.0.0.5 installed to the card and to the emmc.
If anyone has any other ideas, I could really use the help. I consider myself pretty computer literate (build my machines, coded in my spare time in the past, hacked a lot of my electronics). I have read many guides/sites and even tried the outdated stuff. Once again, I cannot get into clockwork recovery, so any guide that says to do that as the first step will not work. I also cannot boot off of the SD on cards that I know function.
Would using an older version of CWM (prior to 3.0.0.5) work? I think I remember reading a bunch of stuff about problems people were having with that version. The thing is, I wasn't installing or flashing anything new. I wish I was, because then I would know what was happening when everything got screwed up.
Thanks a bunch in advance for your guy's (gals?) time. This has been really painful.
Wow, that must be frustrating. First make sure you didn't change the boot settings to something other than the SD card when you were in the boot menu. As long as the Nook is powering on and doing something you can probably save it from being a brick.
I would start with a newer version of ClockWork Mod Recovery here: http://mrm3.net/blog/2011/03/11/nook-color-updated-clockwork-recovery-bootable-sd/
There is a contradiction in the file names but the actual version should be 3.2.0.8. If that doesn't work then you may want to go back to an older version. In that case I would still load a newer version's zip file onto that card, so that if you do get the older version to boot you can use it to flash the newer version.
Before going back to older CWM versions though give this a try if the new CWM above doesn't work http://forum.xda-developers.com/showthread.php?t=958748
JP
Yeah, it has been frustrating, especially not knowing what happened in the first place. I actually did try the version from that first link (where I put 3.0.2.8). Again, the big issue I am having is that I cannot even get into the CWM. If I could, I could fix it. I also saw and read through that xda thread you kinked to (open right now in my browser), but the problem remains that I cannot even get to the point where I can flash something.
Thanks at least for responding. I'll try a few more things and see if it works, but I am running out of ideas.
In theory creating a bootable CWM card will get you into recovery even though you can't access the Recovery on the internal. Once you reach Recovery from the SD card you can flash whatever you need. It is just a matter of making a bootable recovery card that boots far enough to get you there.
In theory, yes, but as I said in my first post, I tried all the bootable cards without any luck. When I try to set the SD card as primary boot from that one screen from fattire, it locks and never restarts.
J515OP said:
Wow, that must be frustrating. First make sure you didn't change the boot settings to something other than the SD card when you were in the boot menu. As long as the Nook is powering on and doing something you can probably save it from being a brick.
I would start with a newer version of ClockWork Mod Recovery here: http://mrm3.net/blog/2011/03/11/nook-color-updated-clockwork-recovery-bootable-sd/
There is a contradiction in the file names but the actual version should be 3.2.0.8. If that doesn't work then you may want to go back to an older version. In that case I would still load a newer version's zip file onto that card, so that if you do get the older version to boot you can use it to flash the newer version.
Before going back to older CWM versions though give this a try if the new CWM above doesn't work http://forum.xda-developers.com/showthread.php?t=958748
JP
Click to expand...
Click to collapse
This happened to me a couple of times on CM7. Don't know why, but I believe I used the last method listed to repair it. There was an older version of CWM that would cause this sometimes. When you get it going again, you must update CMW to the new one.
DigitalMD said:
This happened to me a couple of times on CM7. Don't know why, but I believe I used the last method listed to repair it. There was an older version of CWM that would cause this sometimes. When you get it going again, you must update CMW to the new one.
Click to expand...
Click to collapse
How did you get it to boot into CWM in the first place in order to flash? That is my current problem. Any method of fixing relies on the ability to boot into CWM from the SD card, which (for whatever reason) isn't working at the moment.
Well, tried to use the native Nook u-boot. Get the "Touch the Future of Reading" screen, then black, just like with any of the other cards. On the good nook, it boots into a linux file and runs the recovery script, so it is not the card reader or the SD card.
Well, still doesn't work. I guess I officially bricked it without even knowing what happened. Bummer.
czarofthefrozentundra said:
Well, still doesn't work. I guess I officially bricked it without even knowing what happened. Bummer.
Click to expand...
Click to collapse
You said you tried eyeballers 3.2.0.1 CWM. Did you mean the 1GB image file he posted on his thread? And how did you burn the image to the card? You should be using win32diskimager running in administrator mode on Windows. And it is best to use a cheap card reader rather than any card reader built into your PC. The nook can be really finicky about how the card is written.
leapinlar said:
You said you tried eyeballers 3.2.0.1 CWM. Did you mean the 1GB image file he posted on his thread? And how did you burn the image to the card? You should be using win32diskimager running in administrator mode on Windows. And it is best to use a cheap card reader rather than any card reader built into your PC. The nook can be really finicky about how the card is written.
Click to expand...
Click to collapse
Yes, I tried that image from his thread. I always use win32diskimager and use a card reader. I have working cards (I have a second NC that runs fine); there is just something wrong with the boot process, and I cannot get into CWR to fix it. It starts, but then never makes it in or reboots. Only time I can keep it from rebooting is by holding "n" and going into the boot option menu.
czarofthefrozentundra said:
Yes, I tried that image from his thread. I always use win32diskimager and use a card reader. I have working cards (I have a second NC that runs fine); there is just something wrong with the boot process, and I cannot get into CWR to fix it. It starts, but then never makes it in or reboots. Only time I can keep it from rebooting is by holding "n" and going into the boot option menu.
Click to expand...
Click to collapse
It goes to the boot menu when you hold n with eyeballers image burned to SD? What happens when you select SD and normal? Just a hang? With 'loading' showing?
Edit: I just thought of another reason that could be causing this. There is a flag set in /rom that tells the system to try to boot into recovery. It tries no matter what you tell it to do in the boot menu. ROM Manager uses that flag to boot to recovery when you tell it to. Then after you successfully get into recovery and exit it by telling CWM to reboot, CWM clears that flag. If your recovery is borked up, you never get that flag cleared and it's an endless loop.
There are two solutions I can think of. First, use racks dual boot SD that you already have and go into the boot menu with that. Tell it to go to SD and recovery. Hopefully his recovery will load. Then immediately exit by the menu. That should clear the flag. If that fixes it and it boots to CM7, go to ROM Manager and flash a new CWM to emmc.
If that does not fix it search xda for 'fix recovery'. There is a nook thread telling how to fix the recovery on emmc.
Edit2: I just thought of a third way to try to get it to boot. Take eyeballers 3.2.0.1 CWM SD and put it in your PC. There should be two files there named uImage and uRamdisk. Make a copy of them on the SD and rename the copies to uRecImg and uRecRam. Then put back in nook and reboot to see what you get.
Hmm. Thanks. I'll definitely give it a shot (got nothing to lose at this point). I'll get back and let you know if it worked or not.
czarofthefrozentundra said:
Hmm. Thanks. I'll definitely give it a shot (got nothing to lose at this point). I'll get back and let you know if it worked or not.
Click to expand...
Click to collapse
See my edit2 above for a third way to try to clear the flag.
Sent from my NookColor running ICS and Tapatalk
czarofthefrozentundra said:
Hmm. Thanks. I'll definitely give it a shot (got nothing to lose at this point). I'll get back and let you know if it worked or not.
Click to expand...
Click to collapse
Hello? Feedback?
Sent from my Nook Color running ICS and Tapatalk
Ha, I tried the quick reply function, and it didn't work. Here is what I wrote yesterday (verbatim, since I still had the window open):
"Well, so far no luck. Here is what I have tried, and the new information that I learned.
Used dual boot SD that I know works and booted into bootloader menu. Tried all different options on the SD card. What happens is that it thinks for a bit, then turns the screen black, but the boot screen never comes up (i.e. the Cyanogenmod logo that usually starts before things boot). So there must be some problem there.
If I hold down power, it will restart. Again, the screen turns black after the loading screen is on for a while (happens no matter which image I burned to the card).
I still need to try the other method (eyeballer one). I don't think the EMMC reset will work with my particular issue, as I had read that thread earlier."
czarofthefrozentundra said:
I still need to try the other method (eyeballer one).
Click to expand...
Click to collapse
If the problem is the recovery flag, the mods to the eyeballer CWM SD should work. If it does not work, it may be something else. If it does work you can flash a new CWM to emmc using another eyeballer zip. Get it here:
http://forum.xda-developers.com/showthread.php?p=21932561
You would want the first choice.
Sent from my Nook Color running ICS and Tapatalk
Cool. Will give it a try tonight and report back. Just have to find my spare SD card.
So, tried with the eyeballer, and I couldn't get it to work. One thing I did notice, though (actually by chance) is that even though the screen is black, the nook is on. I saw this because it all of the sudden started flashing the low battery screen and then turned off.
Anyhow, still looks like I am in the same position. The EMMC fix doesn't work for me because I cannot even boot of an SD card.
EDIT: Actually, I just reread your post. I didn't do it right. I am going to try again and report back.
EIDT 2: Nope, didn't work. Do I need to hold all the buttons down while booting or do something else special?
czarofthefrozentundra said:
So, tried with the eyeballer, and I couldn't get it to work. One thing I did notice, though (actually by chance) is that even though the screen is black, the nook is on. I saw this because it all of the sudden started flashing the low battery screen and then turned off.
Anyhow, still looks like I am in the same position. The EMMC fix doesn't work for me because I cannot even boot of an SD card.
EDIT: Actually, I just reread your post. I didn't do it right. I am going to try again and report back.
EIDT 2: Nope, didn't work. Do I need to hold all the buttons down while booting or do something else special?
Click to expand...
Click to collapse
I'm not sure what to tell you to do next. I guess I am going to send you to a post that tells pretty plainly how to do the 8 failed boots. I know you tried that, but timing is very critical with that procedure. Worth a try to me.
http://forum.xda-developers.com/showthread.php?p=25405429
How do you do the 8 failed boot deal with the cyanogenmod screen running. I am not sure about the timing of things. Also, which buttons? I have seen people do it with just the power button. Other places say with the power+n+vol up.
I've tried so many things and I can't get it to work which is why I'm finally posting. I have a Nook Color that had 1.4.3 on it. I used Winimg to make a bootable sd card. Once I plugged it into my nook that was power off, I plugged the power cable in to force it into CWM. I used the SD_ROOT_NT16or8gbV4_7 method. Now my Nook is stuck on the "Touch Android to Begin".
I tried booting back into CWM, then swapping SD cards with CM7 on it and it failed. I found something saying that I needed to remove the first line to fix the failing issue. Well, I did that and it said it installed, but still, nothing.
Help please
Nino
ninobrn99 said:
I've tried so many things and I can't get it to work which is why I'm finally posting. I have a Nook Color that had 1.4.3 on it. I used Winimg to make a bootable sd card. Once I plugged it into my nook that was power off, I plugged the power cable in to force it into CWM. I used the SD_ROOT_NT16or8gbV4_7 method. Now my Nook is stuck on the "Touch Android to Begin".
I tried booting back into CWM, then swapping SD cards with CM7 on it and it failed. I found something saying that I needed to remove the first line to fix the failing issue. Well, I did that and it said it installed, but still, nothing.
Help please
Nino
Click to expand...
Click to collapse
i had to flash 1.4.2 then upgrade to 1.4.3 to have touch functionality on mine. give that a shot
Move thread
Please move this thread to Nook Color Q&A. This forum is strictly meant for Android development. Post questions in Q&A.
Sounds like you are using a Nook tablet ROM on a Nook color. Won't work!
ninobrn99 said:
I've tried so many things and I can't get it to work which is why I'm finally posting. I have a Nook Color that had 1.4.3 on it. I used Winimg to make a bootable sd card. Once I plugged it into my nook that was power off, I plugged the power cable in to force it into CWM. I used the SD_ROOT_NT16or8gbV4_7 method. Now my Nook is stuck on the "Touch Android to Begin".
I tried booting back into CWM, then swapping SD cards with CM7 on it and it failed. I found something saying that I needed to remove the first line to fix the failing issue. Well, I did that and it said it installed, but still, nothing.
Help please
Nino
Click to expand...
Click to collapse
Yes, you did flash a Nook Tablet zip to your Nook Color. That first line that you removed was a safety check to make sure that could not happen. You messed up your partitions. Fortunately for you I have just the thing to fix you up and get moving again. Go to my partition repair thread linked in my signature and flash repair 145678 zip.
Then if you want to put the stock ROM back on, go to my tips thread linked in my signature and look at item A15. Then to root it search the development forum for Manual Nooter 5.08.20.
Sent from my Nook HD+ using Tapatalk