[Q] I brick my L7 Help needed - Optimus L3, L5, L7 Q&A, Help & Troubleshooting

Hey, really i need Yours help, I have a big problem with l7.
Phone is switched on only in emergency, or if i just turn the phone hangs on the LG logo.
I tried to fire up fastboot but jumps secure booting error.
CM10 previously installed according to the instructions in some forum, but did not work the mobile phone network, so I wanted to reinstall the factory soft by KDZ.
Unfortunately, the first attempt was unsuccessful, and now when trying to install any version of the system (V10K, V10a), the phone is detected at the begining, and installs soft, but after this, phone is restarting and freezes on LG logo, and the computer tries to install the driver for "MTP USB Devices" Unfortunately, the driver is not installed and the installation is not coming to an end.
I tried to install the phone in a mode other than CDMA and EMERGENCY, but there is an error in the system "model II msg not found" and the installation ends with the same result.
Mention that several times before installing the factory soft and there were no problems. Perhaps it is a matter of something that I installed on the phone with the CM10 (unlocking bootloader?)
After the installation process in KDZ upgrade error message pops up wparam: 100 lparam: 6
I will be very grateful for any help.
I'm sorry for my english if something is dificult to understand. Then i'll explane everything You need.

solved problem
When the L7 stuck on the LG logo, restart the process, run the file Flash_Bootloader.bat then Flash_Recovery.bat, then Reboot2Recovery.bat. When you get into Recovery Mode, do the restore files that you have done this before, or reinstall CM10 ..... that's all you need to do and your L7 will work again. I hope I helped .... Regards:fingers-crossed::fingers-crossed::fingers-crossed:

I think its communication problem when you flashing through KDZ. Try changing modem port of the phone wich is free and reflash it!

R: [Q] I brick my L7 Help needed
I had this problem too, just flash homero' s V10K and when it finishes DONT disconnect The phone from The PC,when phone is booting fire up terminal on your PC and write adb reboot recovery, Then when you are in CWM wipe data,cache, dalvik and reboot!
Sent from my LG-P700 using xda app-developers app

Hi all,
i have the same Problem, i install the V10K.kdz file
but the L7 freeze at the boot logo... i have no Idea...
i Flash also with this file---> homero' s V10K - the same effect freeze on the Boot logo
hope u can help me
:good: :good: :good:

DuckDagobert007 said:
Hi all,
i have the same Problem, i install the V10K.kdz file
but the L7 freeze at the boot logo... i have no Idea...
i Flash also with this file---> homero' s V10K - the same effect freeze on the Boot logo
hope u can help me
:good: :good: :good:
Click to expand...
Click to collapse
Just follow what I described in the post before yours,and your phone will boot

Hi,
thanks for your Comment :good::good:
I try it 100, but it doesnt work
i dont know, my the Problem is, can u make ah tutorial with Pic ??
or when u are German, can u send me ah PN ??
Greets

Yeah,I'll make a tutorial
Just posted the Thread in Android Development !

Related

L7 Won't start after KDZ Flasher

Hello everyone,Yesterday I flashed CM10 on my L7 with CWM,and wanted to get back on stock rom,so I started KDZ Flasher,put the KDZ in and started the flash,at the end of the process the phone rebooted and still now is STUCK on LG animated logo and won't start,also at the end of the process after some minutes I got this error in a window: Upgrade Error Wparam: 100 LParam:2
I did attach a copy of the log if it can help...
Any solution to solve this?? Thanks in advance !
Wolf80 said:
Hello everyone,Yesterday I flashed CM10 on my L7 with CWM,and wanted to get back on stock rom,so I started KDZ Flasher,put the KDZ in and started the flash,at the end of the process the phone rebooted and still now is STUCK on LG animated logo and won't start,also at the end of the process after some minutes I got this error in a window: Upgrade Error Wparam: 100 LParam:2
I did attach a copy of the log if it can help...
Any solution to solve this?? Thanks in advance !
Click to expand...
Click to collapse
I am also getting the same error if you work out how to fix it please let me know
Did you guys install the Microsoft XML Parser before running the update? Also, make sure to reboot your computer after you install it.
you have to make a hard reset on your device.
:S
i dont trust this KDZ, too many have bricked phones
Wolf80 said:
Hello everyone,Yesterday I flashed CM10 on my L7 with CWM,and wanted to get back on stock rom,so I started KDZ Flasher,put the KDZ in and started the flash,at the end of the process the phone rebooted and still now is STUCK on LG animated logo and won't start,also at the end of the process after some minutes I got this error in a window: Upgrade Error Wparam: 100 LParam:2
I did attach a copy of the log if it can help...
Any solution to solve this?? Thanks in advance !
Click to expand...
Click to collapse
I got the same error when I tried to update from cm10 to v20a try to restart your phone many times and it will open

phone not working for 2 months

please my phone not working for 2 months the proplem is after flash stock rom by kdz phone restart and show lg logo and white screen and restart
this happens with any version availble .....and i cant enter to cwm ...i tried hard reset and change windos..xp.win7 .64 ..same proplem and computer can not read phone information ...and tried to reinstal msxml ....same proplem please i want to work my phone back ....and i tried the 43 page solve and same error becase phone can not enter to cwm .....please if any one know any solve for my proplem ..help.. and i tried befor flash by kzd to disabe modem and same error happens after flash ....
this error show to me.....
abdelnaby85 said:
please my phone not working for 2 months the proplem is after flash stock rom by kdz phone restart and show lg logo and white screen and restart
this happens with any version availble .....and i cant enter to cwm ...i tried hard reset and change windos..xp.win7 .64 ..same proplem and computer can not read phone information ...and tried to reinstal msxml ....same proplem please i want to work my phone back ....and i tried the 43 page solve and same error becase phone can not enter to cwm .....please if any one know any solve for my proplem ..help.. and i tried befor flash by kzd to disabe modem and same error happens after flash ....
this error show to me.....
Click to expand...
Click to collapse
try it on another pc.
or uninstall all lg of your pc then reboot again and reinstall everything again
Have you tried flashing in KDZ with battery removed?
Sent from my LG-P700
lokopol said:
try it on another pc.
or uninstall all lg of your pc then reboot again and reinstall everything again
Click to expand...
Click to collapse
i tried this on 4 another pc ...same error
Hard reseting its when u come back to stock.
How cant u recover it ?
Enter diag mode then select it trought KDZ program-> diag mode
Then start upgrade in program .
Ur phone will turn in emergency mode AUTOMATICALLY so phone recovered
Sent From ... Lg e400 <-- {[Brasilian Here]}

[Q] lge400 bricked need help im a newbie

hi, im new here and i need help i've got a problem on my lg optimus l3. I think my phone was bricked. i can no longer access recovery mode but i still can go to emergency mode. then i tried to use kdz and it try to bring it back to the old l3 which is ginger bread.. oh by the way im using cm9 and sdmerge that time when suddenly my phone restarted and open then restart again.. non stop restarting.. so i decided to format it.. but when i reformat it my memory became 15mb only..
thats the time i tried to use kdz.. but when i used kdz to flash the old firmware im getting an error.. that was the time i can no longer acess my recovery mode. and also when im in emergency mode my pc is not recognizing my phone.. ive redownload and reinstall all the drivers but still no luck..
now i cant open my phone.. it always stuck in lg logo and go to white screen and back to lg logo again..
please someone help me..:crying::crying:
LGE400Addict said:
hi, im new here and i need help i've got a problem on my lg optimus l3. I think my phone was bricked. i can no longer access recovery mode but i still can go to emergency mode. then i tried to use kdz and it try to bring it back to the old l3 which is ginger bread.. oh by the way im using cm9 and sdmerge that time when suddenly my phone restarted and open then restart again.. non stop restarting.. so i decided to format it.. but when i reformat it my memory became 15mb only..
thats the time i tried to use kdz.. but when i used kdz to flash the old firmware im getting an error.. that was the time i can no longer acess my recovery mode. and also when im in emergency mode my pc is not recognizing my phone.. ive redownload and reinstall all the drivers but still no luck..
now i cant open my phone.. it always stuck in lg logo and go to white screen and back to lg logo again..
please someone help me..:crying::crying:
Click to expand...
Click to collapse
does your phone come-up with blank (black but backlit) screen ?
if it does then you will be able to use kdz updater in attached link LG-RDTT_1.0.5.4 (needs included windows enabler for this version)
use THIS GUIDE to flash just skip the hosts file editing steps
and let us know
LG-RDTT_1.0.5.4
IGGYVIP said:
does your phone come-up with blank (black but backlit) screen ?
if it does then you will be able to use kdz updater in attached link LG-RDTT_1.0.5.4 (needs included windows enabler for this version)
use THIS GUIDE to flash just skip the hosts file editing steps
and let us know
dl.xda-developers.com/attachdl/8c343b1d694e531790a4bedc4a0d3dc3/530e4e21/2/5/9/9/9/3/9/LG-RDTT_1.0.5.4.zip
Click to expand...
Click to collapse
ok i will try thanks.. i will let you know immediately. where can i get that LG-RDTT something?
sorry for the bad english
LGE400Addict said:
ok i will try thanks.. i will let you know immediately. where can i get that LG-RDTT something?
sorry for the bad english
Click to expand...
Click to collapse
my computer doesnt recognizing my phone when in emergency mode..
i dont know what to do in the files ive downloaded.. i followed all the instruction..
can you give me pictures or videos...
my phone is not booting and its going white screen and back to lg logo again..
when i try to use VOLUME - plus home and POwer button.. its stuck in lg logo..
when i connect it in pc in that situation the computer reconize my phone but with some failed installing deivce..
i know im doing something wrong but i cant figure it out.. coz im not an expert..
im losing hope that i can bring back my long time lge400 friend..

LG P700 stuck in a boot loop help!!!

Hi everyone
please accept for my poor English straight away and that i am noob
i bought LG p700 from the ebay saying that it is stuck in a boot loop mode so i thought it will be an easy fix which is not at all,
what i found out that it has a clockwordMod Recovery v6.0.3.2 i am not really sure if it helps or not ,
i red i couple topic's how to go back to the stock Rom but it doesn't work for me the the KDZ doesn't found the phone, even thought when i connect it to the computer the windows 7 automatically installed the drivers of the phone,
also i tried to install from my sdcard cm-10-20131006-NIGHTLY-p700 but it didnt work , everything goes fine but in the end it steal stucks in the boot loop,
so is there anyone could help me with is phone i will appreciate it a lot , also i prepared to install a stock Rom because i am a bit an old fashion i got
KDZ_FW_UPD_EN and V20D_00.kdz but as i said when i tried to install it, it didn't go true because i got a message where it says that the phone was not found
many thanks
gugutm
gugutm1 said:
Hi everyone
please accept for my poor English straight away and that i am noob
i bought LG p700 from the ebay saying that it is stuck in a boot loop mode so i thought it will be an easy fix which is not at all,
what i found out that it has a clockwordMod Recovery v6.0.3.2 i am not really sure if it helps or not ,
i red i couple topic's how to go back to the stock Rom but it doesn't work for me the the KDZ doesn't found the phone, even thought when i connect it to the computer the windows 7 automatically installed the drivers of the phone,
also i tried to install from my sdcard cm-10-20131006-NIGHTLY-p700 but it didnt work , everything goes fine but in the end it steal stucks in the boot loop,
so is there anyone could help me with is phone i will appreciate it a lot , also i prepared to install a stock Rom because i am a bit an old fashion i got
KDZ_FW_UPD_EN and V20D_00.kdz but as i said when i tried to install it, it didn't go true because i got a message where it says that the phone was not found
many thanks
gugutm
Click to expand...
Click to collapse
Install LG PC Suite, the LG Mobile Support Tool and the LG L7 USB driver. Then try again. Make sure your phone is set on 3GQCT and EMERGENCY on KDZ.
Before you install a ROM, you're recommended to wipe data.
Bootloops can occurs in many ways, if you can logcat your problem, maybe we can help you.
F4uzan said:
Before you install a ROM, you're recommended to wipe data.
Bootloops can occurs in many ways, if you can logcat your problem, maybe we can help you.
Click to expand...
Click to collapse
hi there im stuck in lg logo i had 4.4.2 but i had some problems with my gps so i decided to go back on v20d i used kdz emergency 3gqct battery out phone in emergency mode and im stuck in lg logo please can someone help me and sorry if my english is bad im from croatia.

STUCK at LG Logo, NO Download mode..Please HELP!!

hi all,
I have posted my G2 problem in another thread but was hoping more people can see it and help me...
PHONE Stuck at LG Logo after power up.
NO Download Mode,
here goes..
Believed I was conned... and this could be what happened to my LG G2 'D802':
my mobile is actually a D801 phone (motherboard) NOT D802 but loaded with D802 ROM
Phone was flashed (by me) with D802 ROM to remove error "Unfortunately, the process com.android.systemui has stopped" caused by corrupted Build.Prop system file during some editing.
touch screen error after new ROM was flashed (tried many diff roms), likely due to incompatible phone settings.
unable to flash D801 kdz since the phone was configured to 'D802', incorrect model detected while trying to flash.
managed to get a D801 TOT file that can resolved the incompatible model issue
Flash completed, phone rebooted..STUCKED at LG LOGO!
pressed Vol+ and USB cable, cannot enter download mode...stucked..
Factory reset using hardware keys, same problem..
please help ! any suggestion/s would be greatly appreciated!! thank you!!
TEDET123 said:
hi all,
I have posted my G2 problem in another thread but was hoping more people can see it and help me...
PHONE Stuck at LG Logo after power up.
NO Download Mode,
here goes..
Believed I was conned... and this could be what happened to my LG G2 'D802':
my mobile is actually a D801 phone (motherboard) NOT D802 but loaded with D802 ROM
Phone was flashed (by me) with D802 ROM to remove error "Unfortunately, the process com.android.systemui has stopped" caused by corrupted Build.Prop system file during some editing.
touch screen error after new ROM was flashed (tried many diff roms), likely due to incompatible phone settings.
unable to flash D801 kdz since the phone was configured to 'D802', incorrect model detected while trying to flash.
managed to get a D801 TOT file that can resolved the incompatible model issue
Flash completed, phone rebooted..STUCKED at LG LOGO!
pressed Vol+ and USB cable, cannot enter download mode...stucked..
Factory reset using hardware keys, same problem..
please help ! any suggestion/s would be greatly appreciated!! thank you!!
Click to expand...
Click to collapse
use flashtool with another *dll
His download mode is not functional.
When in factory reset - connect to pc(does it throw errors or add a new device?)
If yes..then - read this
If no then still read it.
bender_007 said:
His download mode is not functional.
When in factory reset - connect to pc(does it throw errors or add a new device?)
If yes..then - read this
If no then still read it.
Click to expand...
Click to collapse
thanks for replying guys..appreciate it!
yes..download mode is not functional.
When connect to pc at 'Factory hard reset mode' screen (vol- and pwr pressed, letgo and pressed)..nothing happens on either PC or Mobile..
After Hard reset, phone continue stuck at LG LOGO.. PC detected mobile as "LGE AndroidNet USB Serial Port (COM41)", see attached.
I have tried the method in the link above but the PC seems cannot detect phone during cmd "ls /dev/sd*" and "gdisk -l /dev/sdb" .
someone please help..
TEDET123 said:
someone please help..
Click to expand...
Click to collapse
Hey,
I'm currently having some issue too but not the same it seems ..
Have you tried this: http://forum.xda-developers.com/showthread.php?t=2656275 ?
Hope it will help!
shark_max said:
Hey,
I'm currently have some issue too but not the same it seems ..
Have you tried this: http://forum.xda-developers.com/showthread.php?t=2656275 ?
Hope it will help!
Click to expand...
Click to collapse
hey thanks!
i have tried the method in the link but mobile cannot get into download mode...:crying::crying:
TEDET123 said:
hey thanks!
i have tried the method in the link but mobile cannot get into download mode...:crying::crying:
Click to expand...
Click to collapse
But you did in one of your screenshot ...
Anyway, when you let the phone continue to boot, what happend? lot of force close?
Edit : Antoher solution : have you tried to use the official LG Support tool? I did once when my device was completely f****ed up and it restored it by itself!
TEDET123 said:
hey thanks!
i have tried the method in the link but mobile cannot get into download mode...:crying::crying:
Click to expand...
Click to collapse
Just plug your cable to usb. Turn off phone and inmediately hold the button up and ull be in download mode.
Or If U have 801 rom try to root your phone and do recovery as 801 phone, after flash 802 rom !
shark_max said:
But you did in one of your screenshot ...
Anyway, when you let the phone continue to boot, what happend? lot of force close?
Edit : Antoher solution : have you tried to use the official LG Support tool? I did once when my device was completely f****ed up and it restored it by itself!
Click to expand...
Click to collapse
the screenshot stays forever (trying to get into download mode) and did not enter the actual download screen.
if continue to boot, the phone will just hang at LG Logo.
shark_max said:
But you did in one of your screenshot ...
Anyway, when you let the phone continue to boot, what happend? lot of force close?
Edit : Antoher solution : have you tried to use the official LG Support tool? I did once when my device was completely f****ed up and it restored it by itself!
Click to expand...
Click to collapse
LG Support tool was unable to detect my phone..
patriky said:
Just plug your cable to usb. Turn off phone and inmediately hold the button up and ull be in download mode.
Or If U have 801 rom try to root your phone and do recovery as 801 phone, after flash 802 rom !
Click to expand...
Click to collapse
I did this but phone just stays at the 2nd screenshot...
before it was bricked, I have no problem get it into download mode with vol+ and usb cable.
TEDET123 said:
LG Support tool was unable to detect my phone..
Click to expand...
Click to collapse
Wait so what can you do? Hard reset? Download mode? Nothing?
Can you plug your phone and check that your phone is not detected in device manager?
All the drivers are installed?
Same issue
I am having the same exact issue as TEDET123. !!! installed ubunto in one of my PC, tried the same procedure as explain at
http://forum.xda-developers.com/showthread.php?t=2582142&highlight=even+disconnect+lg+phone.
the ubuntu doesn't show any SDB !! need help!!! went to the famous lg software guy in my town. He said MMC chip needs to be replaced ! I knw he doesn;'t have its solution and trying to demotivate me thats it! I knw there must be a solution to this issue!
I would try to force the phone into qhsusb mode then flash only laf.img,aboot.img and boot.img
In qhsub mode you should be able to see the SDB partition
http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404
FaseehUllah said:
I am having the same exact issue as TEDET123. !!! installed ubunto in one of my PC, tried the same procedure as explain at
http://forum.xda-developers.com/showthread.php?t=2582142&highlight=even+disconnect+lg+phone.
the ubuntu doesn't show any SDB !! need help!!! went to the famous lg software guy in my town. He said MMC chip needs to be replaced ! I knw he doesn;'t have its solution and trying to demotivate me thats it! I knw there must be a solution to this issue!
Click to expand...
Click to collapse
Same problem.
Same problem
now can i go back to fast boot mode?
someone please help..
Same problem, please helpp
Same Problem ...... flashing unknown rom and now stuck on LG logo and not entering to download mode please help !! Experts ??

Categories

Resources