Related
Should I charge my phone when it has like 0.5% battery left always, or can I charge whenever it gets a little low, like 30-40%?
Also, can I leave my phone plugged into the charger overnight? Will that drain the battery?
I leave mine in the charger every night. And I'll put it in charge at work, too, or whenever a charging opportunity arises. With this kind of battery, it really doesn't matter.
Here is a very good article that discusses Lithium Ion batteries:
http://batteryuniversity.com/learn/article/charging_lithium_ion_batteries
I don't get the article.
Does 4.2V mean 100% battery life?
If you want to charge it to 4.0 V, does that mean its like 90% battery life?
convolution said:
I don't get the article.
Does 4.2V mean 100% battery life?
If you want to charge it to 4.0 V, does that mean its like 90% battery life?
Click to expand...
Click to collapse
Not certain, but it seems the charger and/or battery on the Vision is designed so that it does not keep the voltage at 100% when its charging and full. I've noticed the battery meter periodically drop to 99% when still on the charger, then back up to "F" (full). While I know the battery meter is not really accurate enough to read to 1% increments; what this seems to indicate is that once a full charge is achieved, the system is going to let the charge drop below a certain threshold, then top off again, rather than keep the voltage at 100% constantly.
The table below is a little more easily digestible (not overly technical). It says you can keep the battery on the charger.
It also says not to let the battery discharge below 20%. Overdischarge of Li ion batteries can result in your battery no longer accepting a charge, on the off chance the safety circuit does not trip properly. The safety circuit is designed to prevent over discharge of the battery, but this has been known to fail, at least on other phones. And there is no benefit to letting the battery discharge below 20%.
http://batteryuniversity.com/learn/article/do_and_dont_battery_table
convolution said:
I don't get the article.
Does 4.2V mean 100% battery life?
If you want to charge it to 4.0 V, does that mean its like 90% battery life?
Click to expand...
Click to collapse
There are two terms you need to understand when it comes to batteries: volts and amps.
Volts is "static" for a battery, meaning it doesn't change. You have a 1.5V battery, it will always be a 1.5V battery. Now the capacity of the battery is measured in amps. A 1Amp battery has more capacity than a 500mAh battery. At 100% fully charged, you'd have 1000mAh (or 1A). At 90%, you'd have 900mAh.
What that article tells you is that your phone is charged to (or close to) 100% using a specified voltage (probably whatever the battery is rated at...3.7V?). Now batteries and chargers of the past had what's called a "trickle" effect, in which it still chargers the battery when it is (or close to) 100%, but at a much lower voltage. If you phone was to stop charging after it hit 100%, it would start to discharge. When you unplugged it (assuming you charge it over night) in the morning, you would have less than 100%. The trickle is so that your battery will still have 100% when you unplug it.
Think about if you filled up your gas tank and left your car running over night. When you woke up, you wouldn't have a full tank anymore. But if you left the gas nozzle in the tank while it was running, it would continually "top it off". That or gas leak everywhere and your car would burst into flames...therefore canceling the point that you wouldn't a full tank...
Anyways...Li-Ion batteries charge and behave differently that batteries of yore. It's bad to let it go down to almost 0%. It's also bad to let it continually sit on the charger. I personally charge mine every other day but I used to charge my Vibrant and HD2 every night.
The batteries in these phones have protection circuits to prevent over charging as well as over discharge. It is perfectly safe to charge over night as well as discharge until empty. What the display shows as 0% does not mean the battery has actually reached 0%. It is just were the protection circuit deems safe. It is possible to over discharge a Li-ion/LiPo battery which may cause it to no longer charge but there are ways to bring it back for the willing. Our phones, however, will not do this due to the protection circuit unless that fails. If that happens you need a new battery because Li-ion/Lipo batteries are very dangerous if over or under charged.
Also, the voltage is static in theory but in real life the the voltage does drop as the battery is discharged. The drop is not large however. A 3.7v Li-ion/LiPo cell will read around 4.2v at full charge and lowers to just over 3.7v at full SAFE discharge. If the battery falls below 3.7v, you will likely have damaged the cell. Again, our phone batteries have a protection circuit to prevent this.
ihateusernames said:
The batteries in these phones have protection circuits to prevent over charging as well as over discharge. It is perfectly safe to charge over night as well as discharge until empty. What the display shows as 0% does not mean the battery has actually reached 0%. It is just were the protection circuit deems safe. It is possible to over discharge a Li-ion/LiPo battery which may cause it to no longer charge but there are ways to bring it back for the willing.
Click to expand...
Click to collapse
It would require a special charger with a "boost" function, which most people do not have access to.
From the previously linked battery University page:
In spite of these preventive measures, over-discharge does occur. Advanced battery analyzers (Cadex C7000 series) feature a 'boost' function that provides a gentle charge current to activate the safety circuit and re-energize the cells if discharged too deeply.
Most of us let our battery drain low on accident from time to time. But it makes not sense to do it intentionally or make a habit of it, as it yields no benefit (some people think they are "conditioning" or "calibrating" the battery, which does not apply to Li ion batteries), and actually hurts battery life. Also from Battery University: "Do charge the battery often. The battery lasts longer with partial rather than full discharges."
There have been pretty occasional cases on the Touch Pro 2 forums of people over-discharging the battery, and rendering it useless. So it does happen. Some have claimed that the Android OS, or the Vision phone itself handles the battery better to avoid over discharge. Maybe so. But do you really want to test that theory, if it can most usually be avoided?
redpoint73 said:
It would require a special charger with a "boost" function, which most people do not have access to.
From the previously linked battery University page:
In spite of these preventive measures, over-discharge does occur. Advanced battery analyzers (Cadex C7000 series) feature a 'boost' function that provides a gentle charge current to activate the safety circuit and re-energize the cells if discharged too deeply.
Most of us let our battery drain low on accident from time to time. But it makes not sense to do it intentionally or make a habit of it, as it yields no benefit (some people think they are "conditioning" or "calibrating" the battery, which does not apply to Li ion batteries), and actually hurts battery life. Also from Battery University: "Do charge the battery often. The battery lasts longer with partial rather than full discharges."
There have been pretty occasional cases on the Touch Pro 2 forums of people over-discharging the battery, and rendering it useless. So it does happen. Some have claimed that the Android OS, or the Vision phone itself handles the battery better to avoid over discharge. Maybe so. But do you really want to test that theory, if it can most usually be avoided?
Click to expand...
Click to collapse
I agree that it can happen which is why I stated that the prevention circuit can fail though I do believe it to be a rare case that this happens. I charge when ever I am near a charger as I don't like to run low but I also don't freak out if I am close to dead. I also charge over night every night and have for years. I just don't believe that it is necessary to worry that my phone has been on the charger too long or that I am running close to 0% as there is redundant protection in place and for the most part, this protection works very well. Hell, your phone COULD burst into flames while holding it next to your ear due to the volatility of the Lithium Ion chemistry if exposed to air but that also very rarely happens.
I believe it is probably worse on the battery to watch movies on the phone while overclocked with the battery getting too hot than to discharge to 0% occasionally.
I do agree that it is pointless to try conditioning lithium batteries as they have no memory effect.
Reviving an over discharged Lithium battery should not be attempted by most. I fly RC Helis and my electrics use 3 or 6 cell LiPo's. On the very rare occasion I kill a cell, I isolate the bad cell and trickle charge until it matches the others and then resume balance charging. The batteries in our phones can be revived in the same manner. It requires low current and constant observation and should not be done by the inexperienced.
At the office I leave my phone in a cradle. When I get calls I remove the phone to answer and then return it to the cradle when done. My battery goes from 100% down to somewhere in the 90's then charges back to 100% in the cradle. Does this repeated process harm the battery in any way? I've read that these batteries don't suffer from the memory effect, but I'm still not sure if this counts as a charging cycle.
Sent from my Desire HD using XDA App
You should always let the battery run down completely some times maybe once a week.
Really? I've read on this forum that there is no need to do that with the new Lithium Ion batteries. I've even read that this could have a negative effect and you should try not to let the battery drain completly.
I don't understand why there isn't a proper battery care section in the manual. Its as if its some kind of voodoo science.
Perhaps not Once a week. But Once a "while"
The reason is that, Phone software uses approximation to calculate the charge left in the Battery. So over time, battery ages and software may not be calibrated to match with the battery's storage capacity. So draining the battery entirely and charging them fully gives the phone's software to assess the battery's health and recalibrate.
It's a lithium battery mate. The only way you can really damage it is by a complete discharge. So long as you don't switch the phone back on once it switches itself off due to low battery you needn't worry about anything else.
Also in theory the lithium batteries have a lifespan of say about a 1000 charges for example and everytime you charge it has one charging less left. This ofcourse isn't exactly how it is in practice but charging the battery alot wears it down. It isn't good either to keep it in the charger for a longer time after it's reached a 100%.
Hi,
this is only partly correct:
Suppose the battery can make 1000 (which I don't believe) charge cycles,
it means that you can charge 1000 times from empty to full.
If you just charge 1000 times from 50% empty to full it counts for 500 cycles!
So,
don't worry, let it stay in the cradle if you like
There are 500 opinions about that but believe, as I wrote is correct.
Theo
Yes, what I said wasn't exact science and I used 1000 cycles as an example, but from what I've read it is better to let the battery drain to less than 50% and then charge it full rather than charge 5% at a time. My previous post was meant to illustrate this.
Sent from my Leedroid powered pocketsized supercomputer using XDA App
geenome said:
You should always let the battery run down completely some times maybe once a week.
Click to expand...
Click to collapse
That's a load of crap, no offense... Lithium batteries have no memory effect and have absolutely no need to be completely discharged, that's a ancient thing from the time of nickel-metal hybrid batteries. The only actual reason for full charge cycles is to calibrate the device for that exact battery.
Keeping a lithium-ion battery in a charger most of the time will wear the battery down faster than getting it drain more and then charging it. Keeping the battery almost fully loaded/in a constant loading state wears the battery capacity by approximately 20% a year (can't recall the source/study just now)(EDIT: and my personal experience is that the battery capacity will wear that much anyway, no matter how you use it). The life-cycle of phones these days are roughly two years nowadays so IMO you can keep it in a cradle with no worries, if you wish. And lets face it, a new battery after a year of usage won't be that big an investment after all.
To add to the above post, running down a lithium battery completely does more damage than benefit. This is almost impossible though with normal use as the phone shuts down long before the battery is completely empty
Is this the definitive way to do it?
http://hemorrdroids.net/battery-calibration/
Those steps came from here, xda devs.
1. Run the device down until it turns itself off.
2. Turn it back on and wait for it to turn itself off again.
3. Remove the battery for 10 seconds.
4. Replace the battery, but leave the device off.
5. Charge the device until full and then for another hour.
6 **Root users only** Using a Terminal Emulator, type “su” enter, followed by “rm /data/system/batterystats.bin”
7. Run the device’s battery down until it turns itself off.
8 .Turn the device on and charge for at least 8 hours.
9. Unplug the device, turn off, then charge for another hour.
10. Unplug the device, turn on, wait 2 minutes.
11.Turn off again and charge for another hour.
12. Restart and use as normal.
Quite a performance! Does it preserve battery lifespan, or is it more to do with slowing down battery drain and does it really work?
He mentions 2 interesting things:
"Generally charge them before they get lower than 50%". I didn't know that, so it's actually better to charge more often and not let it drain down?
"USB charging is actually better for the battery and you may get up to 1 hours more standby time." So you gain an hour standby but it takes twice as long to charge the phone.
Nice manual
Will try it
Sent from my GT-I9100 using Tapatalk
Some will say that its complete nonsense .
Overcharge for 8 hours ??? how does the battery not turn charging off at 100%
Recharge 50% the accepted figure is not to go below 20% to often .
They may be right or wrong their are so many contrasting views on battery charging .
jje
Discharging battery and then reloading it fully, it's the normal procedure for battery calibration for almost all the devices in the world (including computers, etc.).
Step 8 to 11 seems quite a bit strange however.
hm, just seen a different way to calibrate the battery. basically, you drain the battery, take it out for a couple of minutes, put back in, then try to turn it on to make sure it's completely flat.
then you charge it fully, then boot to recovery and wipe battery stats then drain and fully charge. so... which one is more likely to be the better?
that guy also advises to repeat that 12 step, 1-2 day long tedious procedure "every month or so".
it is lunacy honestly speaking
does it work? did he died ?
LOL I dont understand .... I just read in another day that NEVER LET BATTERY GO LOWER THAN 15% and know I read "drain drain drain" Oh welll ...
I also thought that at 100% the charging process stops.
Although this thread is about battery calibration, these questions about battery charging always pop up.
Battery calibration is the process by which you set your device with your battery data.
Every single battery is slightly different. Although there are minimum stantards to every spec of the battery, each battery is different.
Calibrating your battery is nothing more than setting your phone to the real specs of your own battery (since the phone comes configured with the battery factory standards). For example, your phone may be set to use a battery which maximum charge is 1650 mAh, but your battery has a maximum charge of 1625 mAh. That may be within the acceptable factory standard, meaning you have a normal battery, but that also means that your phone will never indicate a 100% charge after you unplug the charger.
If you calibrate that hypothetical battery, you will "tell" your phone that its maximum charge capacity is actually 1625 mAh, meaning from that on your phone's battery indicator will be more accurate.
For that reason, it is necessary to fully discharge and fully recharge your battery for the calibration process, since your device must read the actual specs (minimum charge, maximum charge, charging current, etc) of the installed battery.
I don't know about how many times this full cicle (discharging and recharging) must be performed, but that is the reason why it must be performed for the calibration to succed.
A DIFFERENT THING is the normal discharging and charging process during normal use of the phone.
In this case, you should NEVER let your battery go under 20% and, what few people know, it also should never go over 95%. This stresses the battery and diminish its life time.
Also, and there's a lot of doubts about this, the lower the charging voltage, the slower the charging process, but the longer the battery life.
High charging voltages (like the one used by the charger sold with the phone, which is around 5V) stress the battery, diminishing considerably its life time.
That is true for all lithium-ion batteries!
Therefore it is better to charge your phone through USB (which uses around 4,3V) than to do it using the charger provided with the phone.
You may be asking "If the charging voltage of the charger provided by the manufacturer stresses the battery, why does the manufacturer provide such charger?"
For purely commercial reasons! Higher voltages mean shorter charging cycles, which please the consummer. Moreover, the battery capacity loss with the factory provided charger is around 15-20% a year (considering "normal" to "heavy" use). That is to say that after a year your battery will only reach 80-85% of the maximum charge it used to reach when it was new. And by that time your manufacturer expects you to consider buying a new phone, with more features.
Summing it up:
- calibration is just the process by which you "tell" your phone what the real specs of your battery;
- in normal use, charging your phone through USB is better than doing it with the manufacturer provided charger;
- try not to let your battery charge go under 20% nor above 95%;
- if you're interested, read more about it at batteryuniversity.com
Spin three times in clockwise direction with left middle finger on your nose while blinking your eyes with the phone plugged in.
Jump in the air 3 times.
Unplug phone.
Thats some messed up instructions.
Do you have any idea what kind of strain you're putting on the battery while doing all that?
All you're gonna get is some extra minutes, maybe an hour but is it really worth it because you're just reducing overall battery lifespan by doing that procedure over and over.
Specially when you constantly keep the battery at 4200mV (full charge) for a long time. You're practically killing it by overcharging.
Transmitted from a Galaxy far far away via XDA telepathy.
m2smoe said:
Spin three times in clockwise direction with left middle finger on your nose while blinking your eyes with the phone plugged in.
Jump in the air 3 times.
Unplug phone.
Click to expand...
Click to collapse
that made me chuckle
Never done a calibration on a battery and most of the time i even didn't let battery to discarge very much and then load it again. Never had a problem with battery life it last how long it should last every time and i've used that battery for years. So the battery "calibration" are kinda useless.
Matriak31 said:
that made me chuckle
Click to expand...
Click to collapse
Well then, my job here is done
m2smoe said:
Well then, my job here is done
Click to expand...
Click to collapse
it is indeed...i should follow you just to have more laughs like that cheers
RenatoN said:
Although this thread is about battery calibration, these questions about battery charging always pop up.
Battery calibration is the process by which you set your device with your battery data.
Every single battery is slightly different. Although there are minimum stantards to every spec of the battery, each battery is different.
Calibrating your battery is nothing more than setting your phone to the real specs of your own battery (since the phone comes configured with the battery factory standards). For example, your phone may be set to use a battery which maximum charge is 1650 mAh, but your battery has a maximum charge of 1625 mAh. That may be within the acceptable factory standard, meaning you have a normal battery, but that also means that your phone will never indicate a 100% charge after you unplug the charger.
If you calibrate that hypothetical battery, you will "tell" your phone that its maximum charge capacity is actually 1625 mAh, meaning from that on your phone's battery indicator will be more accurate.
For that reason, it is necessary to fully discharge and fully recharge your battery for the calibration process, since your device must read the actual specs (minimum charge, maximum charge, charging current, etc) of the installed battery.
I don't know about how many times this full cicle (discharging and recharging) must be performed, but that is the reason why it must be performed for the calibration to succed.
A DIFFERENT THING is the normal discharging and charging process during normal use of the phone.
In this case, you should NEVER let your battery go under 20% and, what few people know, it also should never go over 95%. This stresses the battery and diminish its life time.
Also, and there's a lot of doubts about this, the lower the charging voltage, the slower the charging process, but the longer the battery life.
High charging voltages (like the one used by the charger sold with the phone, which is around 5V) stress the battery, diminishing considerably its life time.
That is true for all lithium-ion batteries!
Therefore it is better to charge your phone through USB (which uses around 4,3V) than to do it using the charger provided with the phone.
You may be asking "If the charging voltage of the charger provided by the manufacturer stresses the battery, why does the manufacturer provide such charger?"
For purely commercial reasons! Higher voltages mean shorter charging cycles, which please the consummer. Moreover, the battery capacity loss with the factory provided charger is around 15-20% a year (considering "normal" to "heavy" use). That is to say that after a year your battery will only reach 80-85% of the maximum charge it used to reach when it was new. And by that time your manufacturer expects you to consider buying a new phone, with more features.
Summing it up:
- calibration is just the process by which you "tell" your phone what the real specs of your battery;
- in normal use, charging your phone through USB is better than doing it with the manufacturer provided charger;
- try not to let your battery charge go under 20% nor above 95%;
- if you're interested, read more about it at batteryuniversity.com
Click to expand...
Click to collapse
You should post the source for your info, cause I am seeing a lot of incorrect information in here.
If you guys want to learn about your battery, visit the site Battery University
The OEM replacement battery is worth about $10.
Save yourself the stress....use it...charge it when you need to...if the battery ever fails cough up $10.
Sent from my GT-I9100 using XDA App
The way I would calibrate my batteries is a bit different. Lithium ion batteries don't need to be drained then charged to full AFAIK, and I even remember reading somewhere that draining it is actually only for NiCad batteries. It used to be relevant when phones were using NiCad but not anymore.
Read: http://batteryuniversity.com/learn/article/how_to_prolong_lithium_based_batteries
As such I have read that the universal way to 'calibrate' batteries is by charging to full, using for a couple of mins and charging again.
What I have been doing is:
1. Charge to full when phone is switched off (doesn't matter if it's from 0% or 99%).
2. Switch on the phone, use for 5 mins.
3. Switch off then charge until full.
4. Repeat step 2 once more
That's it! It seems pretty simple but it seems to have worked for me.
The way i do it is different. Firstly i have the battery calibration app from the market by Nema..then i fully charge my phone and when it says its fully charge i go into the app. There it gives me the instructions on how to calibrate...First i wait till i charge the phone without any interruptions. then click on the app and wait til the battery goes to 4200MV and then i press the calibrate button and then the app does it for me. Then i drain the battery again without any interuptions or breaks during that time and then charge it again once battery dies down and thats it.
there are so many ways being touted on the forums you really dont know which one to go for...but whatever works for each person then who are we to tell someone different just thought i share that
If my battery dies, or gets significally lower capacity after 1 or 2 years of usage, I'll just buy a new one if I plan to keep the phone longer.. Going through these rituals and painstakenly monitor my battery % so that it never goes below 20 % or above 95 % is just not worth it.. Doesn't increase the life THAT much anyway.. I use the phone until I hear the beep for low batt, and from there until I have a charger available.. Most of the time it's before it reaches 10 %, thats good enough for me.. Once in a while it might even go so far that it dies.. Then I charge it till it says 100 %.. Most of the times I plug it when going to bed, and let it charge over night.. This is normal usage and what the battery should be designed to handle, and so far it does..
Hey guys, I recieve my s7 edge today, whats the best way to condition the new phones battery? Some use what it has until its low to recharge until 100 others leave phone off and charge to 100 at start, whats the best result for a good healthy battery?,
Thanks
Lithium ion batteries have come a long way. There is no "memory effect" and conditioning is probably not really all that necessary. If I were you I'd just give it a charge to 100 and use as normal. Might have high drain for the first few days/charge cycles.
Remember that with Li-Ion batteries a "charge cycle" is one complete cycle from 0% to 100%. So by charging when it's at 50% you're only using up one half of a "rated charge cycle" - Battery conditioning shouldn't really be required with modern lithium ion batteries.
Battery conditioning isn't necessary but charging fully and depleting fully will help the phones software learn the battery capacity and give the most accurate percentage remaining reading. I'd say do this a couple times after you first get the phone
gaff15 said:
Battery conditioning isn't necessary but charging fully and depleting fully will help the phones software learn the battery capacity and give the most accurate percentage remaining reading. I'd say do this a couple times after you first get the phone
Click to expand...
Click to collapse
This makes sense I guess. But wouldn't the battery percentage remaining be based on the voltage in the battery at a given moment? I wouldn't think the phone would need to "learn" that.
Afaik. It's actually bad to discharge li-ion and li-po batteries down low. I think it's better for battery health to recharge around 50% for instance than waiting until 0%.
Xileforce said:
Afaik. It's actually bad to discharge li-ion and li-po batteries down low. I think it's better for battery health to recharge around 50% for instance than waiting until 0%.
Click to expand...
Click to collapse
The 50% mark is an old(and still good) rule of thumb primarily for lead acid batteries.
Leaving these batteries in a discharged state can be bad for them, but in normal usage even a discharge to 0% is fine if followed shortly by a charge cycle. These devices have a low voltage cutoff which is what shuts the phone down and protects the battery from over discharge and damage. Bottom line is use and charge it however you like, the only thing that may change is the time it takes the software to learn your discharge profile and show accurate stats.
Ashevar said:
The 50% mark is an old(and still good) rule of thumb primarily for lead acid batteries.
Leaving these batteries in a discharged state can be bad for them, but in normal usage even a discharge to 0% is fine if followed shortly by a charge cycle. These devices have a low voltage cutoff which is what shuts the phone down and protects the battery from over discharge and damage. Bottom line is use and charge it however you like, the only thing that may change is the time it takes the software to learn your discharge profile and show accurate stats.
Click to expand...
Click to collapse
This makes sense. The article I read awhile back was likely referring to non smart charging systems, such as a battery pack. It makes sense that an integrated solution such as a phone would regulate that to maintain battery health.
There are three things that are very bad for Li batteries. 1: overcharging. 2: completely draining. 3: overheating. Li batteries are happiest, and will last the longest, if never cycled above 75% or below 25%. Cars like the Tesla actually show 100% charge when the battery pack is only about 75% charged, and show the battery as depleted well above 0% charge. Then again, the battery pack for a Tesla costs a lot more than a phone.
#1 shouldn't be a problem in any modern device. The circuitry in the battery will tell the phone when to shut down charging to prevent overcharge. #3 can be a problem. If you're charging the battery simultaneously with high battery draining phone usage (e.g., GPS and Nav) phones can get very hot. In fact, I've had my phone stop charging and display a warning when I was navigating and charging the phone wirelessly at the same time. If you're using GPS on a long trip, you almost have to charge it while in use, but might want to avoid wireless or fast chargers. Wireless chargers and fast chargers generate more heat.
#2 is up to you. Repeatedly discharging the battery to single digits will reduce it's lifespan. I try to recharge before 25% but if I get into a situation where I can't I don't obsess over it. I don't worry too much about charging to 100%. I suspect that, like Tesla, 100% is probably not really 100%. The battery manufacturers are likely to leave a little safety margin in there to ensure batteries can't overheat and catch fire.
meyerweb said:
There are three things that are very bad for Li batteries. 1: overcharging. 2: completely draining. 3: overheating. Li batteries are happiest, and will last the longest, if never cycled above 75% or below 25%. Cars like the Tesla actually show 100% charge when the battery pack is only about 75% charged, and show the battery as depleted well above 0% charge. Then again, the battery pack for a Tesla costs a lot more than a phone.
#1 shouldn't be a problem in any modern device. The circuitry in the battery will tell the phone when to shut down charging to prevent overcharge. #3 can be a problem. If you're charging the battery simultaneously with high battery draining phone usage (e.g., GPS and Nav) phones can get very hot. In fact, I've had my phone stop charging and display a warning when I was navigating and charging the phone wirelessly at the same time. If you're using GPS on a long trip, you almost have to charge it while in use, but might want to avoid wireless or fast chargers. Wireless chargers and fast chargers generate more heat.
#2 is up to you. Repeatedly discharging the battery to single digits will reduce it's lifespan. I try to recharge before 25% but if I get into a situation where I can't I don't obsess over it. I don't worry too much about charging to 100%. I suspect that, like Tesla, 100% is probably not really 100%. The battery manufacturers are likely to leave a little safety margin in there to ensure batteries can't overheat and catch fire.
Click to expand...
Click to collapse
#1 -> Could be a problem. Manufacturers can set the 100% mark at higher voltage to make it look like it has more capacity while sacrificing longevity, just enough to get through the 1 year warranty period. (Lot of powerbanks do this!) Users have no control of this ceiling. Charging to 80% and letting it cycle below that probably keeps the battery much healthier than keeping it plugged overnight at 100%.
There's an app called AccuBattery on playstore that people might want to check out. It's basically an alarm that turns on when the battery is at desired % level. It also cites real research papers so I would trust what they are doing.
I used to have a long post with a detailed technical explanation but lost it.
Anyway the gist is, basically, batteries work by ion movement, and like a machine, these ions wear out over time due to use. And similar to machines, heavy use wears them out more. You're more likely to break an engine by running it for 1 day at max rev, than running it over a month at half capacity. The smaller the depth of discharge, the lower the wear. Lab tests have concluded that when you constantly discharge from 100 to 0, it allows you betwrrn 300-500 charge cycles before it starts to break down and not hold charges. More specifically, when you reach that magic number your battery can only hold 75% of it's original charge. That's typically 1-2 years of use if you charge once a day. And heavy abusers charge more than once a day, so that decreases the time span to however many weeks it takes them to reach 500 charge cycles. Now, the increase in charge cycles is exponential, not arithmetical. So a depth of discharge to 50 before recharging will not give you 600-1000 charges. Rather it will give you 1200-1500 charge cycles. Mathematically, draining a 3600mah to zero for 300 charges gives you 1080000mah to burn through however short your battery life will be. On the other hand, using only 50% of the battery before recharging gives you 2160000mah to burn through before it expires after at least 1200 charge cycles. In other words, it stored twice more power for you to use. If you say, charge once every 24hrs, going always from 100 to 0 gives you at least 300 days. Recharging twice a day at 50% gives your battery at least 600 days of use before battery capacity deteriorates noticeably. Discharging to 75% before recharging actually gives you 2000-2500 charge cycles, making it even longer. Basically the point is, always plug the phone in when given the chance. Don't wait for 50%, or whatever. 40% is an arbitrary number actually, not sure why it's chosen. Also, this is why one of the choices to auto activate power saving in the S7 is at 50%, so that it keeps the battery up as close to 50% as possible when you get the chance to plug in.
As for charging to 80%, this is because partial charge is better than full charge for lithium ion batteries. The ions are placed on stress to hold charges. Maximum stress is at 100% charge. And like everything else, stuff tends to break more. So not running it to 100% all the time will reduce overall stress experienced and increase the time before deterioration occurs. Personally I charge to 90%, and discharge to 40% or above. That's a 50% depth of charge, so that's good for up to 1500 charge cycles, plus whatever number of cycles the decrease in max stress gives me.
However, note that environmental temperatures also play a role in battery longevity.
Sent from my Galaxy S7 Edge Duos via Tapatalk
just use the dang phone...
cri[LIST=1 said:
[/LIST]s_epic;65635276]Hey guys, I recieve my s7 edge today, whats the best way to condition the new phones battery? Some use what it has until its low to recharge until 100 others leave phone off and charge to 100 at start, whats the best result for a good healthy battery?,
Thanks
Click to expand...
Click to collapse
That's actually a perfect way to ruin your battery on purpose!
Just do these things and Don't worry a lot. And remember, when it does die it's not your fault, it's kind of a problem with Lion batteries!
1. Try to keep the battery between 40-80% or 20-40%. But don't worry if tou can't. Saying this in case you're staying at home all day.
2.Keep the heat away from it!!! This one is important
3. Try to discharge it at a lower rate but don't let that get in the way of you enjoying your device.
4. Try not to discharge below 8% at all. But try to not discharge it below 15-20% unless you have important things to do.
5. don't keep it topped of for a long time (like constant going 90-100%, this is damaging) and don't keep it at 100% for long! (For example turning it off and stop using it for a week, or keeping it plugged for a few days)
If you're storing it keep it at 40% (3.8-3.75V) and try to drain it once in a while. (Unlikely to happen with a phone specially one without a removable battery )
I really do hope someone invents a new type of battery. Lipos are anoyying
Simple you don't need too lol
Sent from my SM-G935F using XDA-Developers mobile app
Hello!
I just received my new S7 edge and boy I love it. I have charged it only twice and now as it is 11 pm and my phone is left with just 17% battery, I need to charge it.
So I usually charged my old HTC One M7 overnight, not thinking about how it might ruin or damage the battery.
But how about the S7 edge? When does the adapter in the outlet know, when to stop charging?
The S7 supports fast charging, which I am using.
But with 6 hours of sleep, won't it over-charge overnight?
Since it's still sending small electrical pulses into the battery even though it's full.
Please help me!
Charging overnight shouldn't do damage. However, try to decrease use of fast charging. It creates more heat than normal charging, and heat exposure damages the battery.
You also want to charge your battery before it hits 40%. This is due to how lithium ion batteries work. Also, most recommendations say charge only to 80%.
Anyway the gist is, basically, batteries work by ion movement, and like a machine, these ions wear out over time due to use. And similar to machines, heavy use wears them out more. You're more likely to break an engine by running it for 1 day at max rev, than running it over a month at half capacity. The smaller the depth of discharge, the lower the wear. Lab tests have concluded that when you constantly discharge from 100 to 0, it allows you betwrrn 300-500 charge cycles before it starts to break down and not hold charges. More specifically, when you reach that magic number your battery can only hold 75% of it's original charge. That's typically 1-2 years of use if you charge once a day. And heavy abusers charge more than once a day, so that decreases the time span to however many weeks it takes them to reach 500 charge cycles. Now, the increase in charge cycles is exponential, not arithmetical. So a depth of discharge to 50 before recharging will not give you 600-1000 charges. Rather it will give you 1200-1500 charge cycles. Mathematically, draining a 3600mah to zero for 300 charges gives you 1080000mah to burn through however short your battery life will be. On the other hand, using only 50% of the battery before recharging gives you 2160000mah to burn through before it expires after at least 1200 charge cycles. In other words, it stored twice more power for you to use. If you say, charge once every 24hrs, going always from 100 to 0 gives you at least 300 days. Recharging twice a day at 50% gives your battery at least 600 days of use before battery capacity deteriorates noticeably. Discharging to 75% before recharging actually gives you 2000-2500 charge cycles, making it even longer. Basically the point is, always plug the phone in when given the chance. Don't wait for 50%, or whatever. 40% is an arbitrary number actually, not sure why it's chosen. Also, this is why one of the choices to auto activate power saving in the S7 is at 50%, so that it keeps the battery up as close to 50% as possible when you get the chance to plug in.
*
As for charging to 80%, this is because partial charge is better than full charge for lithium ion batteries. The ions are placed on stress to hold charges. Maximum stress is at 100% charge. And like everything else, stuff tends to break more. So not running it to 100% all the time will reduce overall stress experienced and increase the time before deterioration occurs. Personally I charge to 90%, and discharge to 40% or above. That's a 50% depth of charge, so that's good for up to 1500 charge cycles, plus whatever number of cycles the decrease in max stress gives me.
However, note that environmental temperatures also play a role in battery longevity.
Sent from my Galaxy S7 Edge Duos via Tapatalk
No harm in leaving it plugged in all night and charging to 100%. The phone controls the battery from being overcharged, not the charger. I've switched off fast charging on mine, as that can be hard on a battery over time and I have no need for it charge any faster than overnight.
Thanks for the info. I didnt know that. And does the battery also work better, as in gives you more SOT if you charge it like you said?
Saridas said:
Thanks for the info. I didnt know that. And does the battery also work better, as in gives you more SOT if you charge it like you said?
Click to expand...
Click to collapse
No it won't. It just makes the battery last longer before it needs replacement. It's not going to affect how fast you drain your battery because that's dependent on your usage.
Sent from my Galaxy S7 Edge Duos via Tapatalk