I rooted my NST a long while back. It slowly started dying over time but I was lazy, didn't bother to unroot and swap it in a timely manner (got the extended warranty) and now it is stuck "Off", as in won't start. That wouldn't matter, only it froze with the rooted navigation icons that button savior brings up showing on the screen! Oops.
In additional to the existing problems (sticking buttons, dead region on screen etc.) the battery indicator started showing a question mark two days ago. A while later it died and wouldn't start. I tried charging, of course, and lots of long power button presses, but the only life I've seen is when I took the card out: at that moment it went through a normal startup... and promptly died showing the stock Home screen with the additional icons overlayed as if I'd triggered the "button savior" app.
Anyone have any ideas of a way to clear the screen? Any suggestions on getting it to boot? I saw I can't crack the case without removing the telltale on the torx screw under the power button.
I don't want to walk into the store and have them decline to swap because it is rooted, even though the problems it has are physical.
Thanks for any suggestions, and for providing the original instructions I used to root - made it worthwhile to get the device in the first place!
My first thought was to just borrow somebody's working Nook and plug your display in long enough to set some image.
But that would make you lose the little sticker on your Torx screw.
OTOH, would they really check that? Certainly not in the store.
I was wondering if an external high voltage would be enough to influence the little pearl spheres.
Thanks
Renate NST, thanks for the suggestions. As it turned out, I just went ahead and tried returning it in the store. This is one case where seriously horrible employee attitude actually helped!
The short version:
they swapped it with no problems and you're right, they wouldn't have noticed the torx telltale missing!
Long version:
I found the screen is surprisingly resistant to damage. Out of curiosity I tried a hair dryer, impacts, magnet. Then again, a 100 lbs dog's claw on the screen had left a small unresponsive region a while back. I didn't think any of those would work, but thought I'd try - why not? won't "hurt" to hurt it. Couldn't think of a good way to get a charge to the screen.
I arranged a swap at the store by calling the central number. I got the email saying the device was on hold and headed out. The store called while I was on the way there (left voicemail - was driving afterall) saying they had no refurbished ones in stock. I went ahead anyhow, hoping I'd get a new one instead. No luck, they had the refurbished ones. I don't know what that was about.
They didn't even look at it. For that matter, they hardly looked at me. I asked one person, who argued with another about who would help me (no other customers needing help - just didn't want to help). I won't bother you with details, but the attitudes of all there were rather amazingly bad. I am slow to blame employees for the problems encountered shopping - normally it is the company I fault - but all three employees there spent much more effort arguing about who would have to help me than actually swapping the nook. They never once looked at it, didn't even ask what was broken about it, and I certainly could have gotten away with opening it up and, I don't know, taking a spare battery or whatever out of it. Oh well. Live and learn.
Now to see what the status of rooting is. I got the original one within a couple days of the first instrucitons on rooting hitting the web, seems things have changed a bit... so glad this forum is here.
At Worst...
You can do the "hard reset". Charge you NST totally and press the energy button for 60 seconds.
Related
Hi all,
I need help,suggestions,anything with an issue I've had for a while. Since the time I started loading WM6 the screen has been randomly fading to white. I have LSVW latest rom 22/4 SE and 1.40.10 radio and 1.40oli although it doesn't matter what rom you load. I tried going back to WM5 and its better but now still fades to white as well.
on advise from oli and legolas I purchased a new battery but still have the same issue.
I have dropped my phone once which resulted in a crack to the right of the DEL/CR keys so could it be a HW issue and if you think so is it one I could open up the phone and fix?
Any and all help appreciated
IN FACT IF SOMEONE CAN RESOLVE THE ISSUE I WILL DONATE SOME CASH TO THEM!
test
Im updating to
LVSW 4-23 Full, Radio 1.40.30.00, SPL 2.10.Oli, IPL 1.04
seeing if any difference comes out.
This is not the first time this issue has been reported:
http://forum.xda-developers.com/archive/index.php/t-301003.html
The conclusion is that it's hardware related. It may be as simple as one of the internal ribbon connectors having a less than firm connection. It may be brought on my anything from physical movement or pressure to internal pressure if the device gats warm. However, it is possible that there is a failing component. IMHO, a case of take it for replacement/repair or first check connectors if your brave and not worried about a warranty.
Mike
mikechannon said:
This is not the first time this issue has been reported:
http://forum.xda-developers.com/archive/index.php/t-301003.html
The conclusion is that it's hardware related. It may be as simple as one of the internal ribbon connectors having a less than firm connection. It may be brought on my anything from physical movement or pressure to internal pressure if the device gats warm. However, it is possible that there is a failing component. IMHO, a case of take it for replacement/repair or first check connectors if your brave and not worried about a warranty.
Mike
Click to expand...
Click to collapse
HHmmm interesting thread .. the only issue i have out of that is the fade to white one.
Maybe Hardware .. i got the phone off ebay and now it has a crack in it .. so i dare say it isnt under warranty any more. (even though its a max of 6 months old).
It may also be software. I experienced the WSOD on my JASJAM when playing with the GPS-related DLL's. Once this problem appeared when switching on the camera. The screen would turn white and soft reset would not fix this, only power off/on would sort it out. Seems that the drivers do not reset (some of) the hardware to a known state on boot.
Had EXACTLY the same problem. Hoped it would be a software problem. Hard-reset a few times to no avail. Upgraded to a couple of the WM6 ROMs. No change. I did notice that when it was cool it tended not to happen, but after being on the phone a couple minutes or using the PDA for a while, it would do it AGAIN.
One weird thing I noticed was that if I did a Soft-reset and held down the Left Soft-key, I could "force" it to fade to white on start-up! VERY WEIRD.
I finally bit the bullet, and sent it back to Telstra to get it sorted. Didn't want to void warranty myself.
It has been just over 2 weeks since I sent it off, and They have sent this reply...
-------
-------
Hi
This phone is currently waiting on a part which was ordered yesterday. Some parts have already been issued but needs further repair.
Regards
Nadine
--------------------------------------------------------------------------------
From: LJ Boyd [mailto:[email protected]]
Sent: Friday, 20 April 2007 2:18 PM
To: ! TMS Customer Service
Subject: RE: Imate JASJAM Problem
Hello, I am emailing about an I-Mate JASJAM phone I sent for repairs early last week (tel # xxx ).
Can you please update me as to status of this repair, as the Telstra shop did not provide me with a second phone while I await return/repair/replacement of the phone.
Thanks,
-------
-------
So, I guess it IS a hardware problem. But then again, that kind of reply, sounds a bit "dodgy" as it doesn't seem to "technical" does it?
Hope this helps.
jyetara said:
So, I guess it IS a hardware problem. But then again, that kind of reply, sounds a bit "dodgy" as it doesn't seem to "technical" does it?
Hope this helps.
Click to expand...
Click to collapse
Their reply was not very technical - does not surprise me however. The people who repair these devices are usually faced with some component/connection/screen or a m/board that needs replaced. They often fail to take account of something as basic as the case pressing on the screen or other components - particularly when device is warm. So they replace the component they think is faulty and then discover the problem is still there. With this issue in particular I think that there are no faulty components just the case is a fraction of a millimetre too tight for the internal components and hence swapping out parts can have no effect. With this fault I advise people to go for a replacement not a repair if possible.
NB: This issue should not be confused with white screen that may appear after installing particular software or when an application crashes, or when the flashing of a new ROM goes wrong! The hardware issue arises most commonly when the device gets warm or put another way goes white after maybe 10 minutes of use and will continue to go white even after hard reset.
Mike
I have this same problem! =(
My phone screen recently (4-5 days ago) started to go white. I never saw this happen with my own eyes but when i picked up my phone and its sleeping i push the power button to get to an all white screen. I can hear noises when i touch the screen but no image other than white. I can solve this by removing the battery and putting it back in, then my scren works fine....its not verry often just like 1-3 times a day.
I want to try a hard reset but have a question first: My phone is unlocked by the ebay guy i got it from, will a hard reset lock my phone back to Cingular?
Next i want to try upgrading my ROM and Radio and anything else...im looking in the wiki for instructions on how to do this. Any help? What else shouls i upgrade?
Ive only had my Hermes for around 2 months so im new to much of this.
THanks!
I recently purchased a Used Imate Jasjam (Ex Telstra Australia) with this issue.
I pulled the unit apart, and reseated and pressed the Power and LCD Display Data Cables... attempting to ensure they were firmly fastened.
I then upgraded to LVSW's Latest WM6 Release.
I have had the Phone go to White once in that timeframe since. I brought it back by pressing the power button of, then one again.
I don't feel that it's really a "100%" Faulty Part... Because it works fine othertimes. It almost seems as if connections or a Data Cable has an Issue.
I'm intending tonight and using the Phone over the weekend to see if the issue continues to occur.
BAD NEWS!!
Well, got my phone back after a bit over 3 weeks I think? I kept ringing the repair center and emailing. Finally they said it was ready, and was sent back to the shop I bought it from. Rang the shop "no it's not here yet, we will ring you"... now the repair centre to the shop is a 20 min drive... on the 3rd, I rang again at 1pm and "no it's not here yet, we will ring you when it arrives." At this point I was really getting p*ed off. So I went to the shop, and demanded, and guess what was AT the Shop?!?!?!
Anyway, after 1 friggin day, I have lost the Red & Green phone buttons! As of tonight the whole bottom section no longer work, and the screen has gone white again.
The repair report listed 3 things replaced...one was a "bezel" another was a "poly" something. I will get the report a list the replaced bits if anyone likes, but their descriptions are kind of strange if ya ask me.
Anyway, I have to send the phone back for repairs again, which could take another 3 weeks +, which I think is completely PATHETIC OF TELSTRA, especially for the fact they dont give the same phone or even similar to "loan" while I wait for my defective $1300 phone to get "repaired"... (more like 'fiddled with' & "yeah, she'll be right mate"...
GRRRRR!!!!
My girlfriends phone was having the same problem. Try popping out your SD card and putting the phone into/out of sleep and see if that brings back a visible screen. Thats how we determined her situation was a hardware problem and not a problem with the rom.
jyetara said:
Well, got my phone back after a bit over 3 weeks I think? I kept ringing the repair center and emailing. Finally they said it was ready, and was sent back to the shop I bought it from. Rang the shop "no it's not here yet, we will ring you"... now the repair centre to the shop is a 20 min drive... on the 3rd, I rang again at 1pm and "no it's not here yet, we will ring you when it arrives." At this point I was really getting p*ed off. So I went to the shop, and demanded, and guess what was AT the Shop?!?!?!
Anyway, after 1 friggin day, I have lost the Red & Green phone buttons! As of tonight the whole bottom section no longer work, and the screen has gone white again.
The repair report listed 3 things replaced...one was a "bezel" another was a "poly" something. I will get the report a list the replaced bits if anyone likes, but their descriptions are kind of strange if ya ask me.
Anyway, I have to send the phone back for repairs again, which could take another 3 weeks +, which I think is completely PATHETIC OF TELSTRA, especially for the fact they dont give the same phone or even similar to "loan" while I wait for my defective $1300 phone to get "repaired"... (more like 'fiddled with' & "yeah, she'll be right mate"...
GRRRRR!!!!
Click to expand...
Click to collapse
Yes, sadly this is kind of predictable as I said in an earlier post in this thread:
http://forum.xda-developers.com/showpost.php?p=1233420&postcount=7
This is why, as I said, get a replacement not a repair if possible. My view is that the individual components are fine but connectors come loose or the heat generated causes pressure to be put on the screen etc So it's a problem with some cases and how the innards in some cases get squeezed. So off course changing the top poly board, connectors, bezel gasket, may by pot luck make a difference but is just as likely to make no difference at all.
Mike
Status Report:
After having my phone playing Video's Through the Night (My Way of a "Stress Test" to Generate Heat) I woke up the find the screen to be "almost completely" White.
Usually its gone completely, however in this instance I was able to see the icons through the whitewash.
I put the phone into sleep and back out and the Display is fine again.
Being that these phones are much easier to pull apart and put back together than my old JasJar I might to do some further experimentation.
I think the issue will have something to do with either one of the following
- Heat
- Pressure on the LCD from Parts Around it
- Faulty Ribbon or Power Leads to the LCD
My suggestions
- In the Case of Heat... I'll run the Same Test, with the Phone Directly in front of a small airconditioning unit I have.
- In the Case of Pressure, I'm going to look and see if I can place some extra Insulation Tape or Similar on the Phone to relieve this
- I wish I could find somewhere to buy the Replacement Ribbon Cables but I don't know where I can get them in Australia... any ideas?
VolarisPtyLtd said:
Status Report:
After having my phone playing Video's Through the Night (My Way of a "Stress Test" to Generate Heat) I woke up the find the screen to be "almost completely" White.
Usually its gone completely, however in this instance I was able to see the icons through the whitewash.
I put the phone into sleep and back out and the Display is fine again.
Being that these phones are much easier to pull apart and put back together than my old JasJar I might to do some further experimentation.
I think the issue will have something to do with either one of the following
- Heat
- Pressure on the LCD from Parts Around it
- Faulty Ribbon or Power Leads to the LCD
My suggestions
- In the Case of Heat... I'll run the Same Test, with the Phone Directly in front of a small airconditioning unit I have.
- In the Case of Pressure, I'm going to look and see if I can place some extra Insulation Tape or Similar on the Phone to relieve this
- I wish I could find somewhere to buy the Replacement Ribbon Cables but I don't know where I can get them in Australia... any ideas?
Click to expand...
Click to collapse
We wait to see. Mind you one guy on these boards found he could get half an hour from his device if he put it in the freezer for a while - so I'm not sure that air-con will be strong enough!!!
Mike
Well Results.....
After pulling apart the unit and reconnected, I think I found my cause to simply be excess pressure.
I've removed the "Black Plastic" Micro SD Card from its Blanking Plate.
Since I've done this... not one White Screen Whatsoever.
I don't use an SD Card, so the issue is resolved for me, however it is very interesting.
Could be Pressure or Heat (Small Hole Might Increase Airflow/Allow for Greater Dissapation or something)
Hi folks,
i've also small experience with this "white screen" issue and just wanted to inform you about it.
I got the device from my former boss who did already complain about this "white screen" issue on his O² XDA trion with original ROM. (honestly i did not really believe him due to my experience with couple of other devices so after i got the device i was just wondering - ok back to the facts).
I installed on Friday the Windows Mobile VI Pro - BLACK 2.5 Release and until today it was running (as far as i remember expect one time) nearly perfect w/o white screens. About 45min ago, i flashed the device with BLACK 3.0 Release and got until now about 5-10 times a white screen.
I assume this is not a hardware ONLY issue but indeed very strange.
I'll go back to 2.5 and will look forward if i get again the white screen or it'll be ok.
Cheers so far
FaCeOff said:
Hi folks,
i've also small experience with this "white screen" issue and just wanted to inform you about it.
I got the device from my former boss who did already complain about this "white screen" issue on his O² XDA trion with original ROM. (honestly i did not really believe him due to my experience with couple of other devices so after i got the device i was just wondering - ok back to the facts).
I installed on Friday the Windows Mobile VI Pro - BLACK 2.5 Release and until today it was running (as far as i remember expect one time) nearly perfect w/o white screens. About 45min ago, i flashed the device with BLACK 3.0 Release and got until now about 5-10 times a white screen.
I assume this is not a hardware ONLY issue but indeed very strange.
I'll go back to 2.5 and will look forward if i get again the white screen or it'll be ok.
Cheers so far
Click to expand...
Click to collapse
You are right to ask the question "is it hardware or software".
1
We know a white screens can arise if folk duff up flashing a new ROM.
2
We know there is a hardware caused white screen that comes and goes often when device gets warm.
3
But there maybe white screens caused by some kinds of crashing software or a buggy ROM etc
Crucially in terms of finding a cure will be distiguishing between these.
2 for most people is easy - take it back and get a replacement.
1 is a matter for the ROM upgrading and fixing boards
3 is a case of trying different ROMs testing 3 party software by selective installation until the problem starts or stops.
In your case I am worried that this is a number 2 device as it did sometimes get the problem before you flashed the ROM and now it's worse. It may only be worse because this particular ROM is generating more heat and consequently more white screens. (see explanations elsewhere).
I suppose if it's an occasional problem you might live with it but otherwise it's replacement at best and repair as a rather dodgy alternative.
Mike
Hey Mike,
well, before flashing the device with a custom ROM, in my opinion it was really difficult to use it.
By flashing it with V 2.5, it was very good usable and with V 3.0 it returned to become more unusable. Nevertheless, i upgraded 10min ago with HARD-SPL-V7 and it's running fine now (i've been wating with downgrading to V 2.5. If it returns to become unstable, i will downgrade to V 2.5 again.
I'll keep you informed.
yes for this particular "white screen" issue it will be useful to hear how things go - thanks
Mike
White screen - in my case definitely a hardware issue
Hi folks,
i was testing and playing around with my Hermes and today i found the problem (very funny because now i can't reproduce it anymore but just read ahead).
Today i was playing around and after pressing by accident on the case of the Hermes, the screen appeared disappeared and changed into white.
Please download the video i recorded from the attached link - you'll see that it was able to reproduce it by tapping on the case:
http://asuka.descipe.de/dphome/test/HTC_Hermes_White_Screen_issue.mp4
Please use VLC or MPC (additional codecs required) to watch the movie.
Honestly i'm not sure if this can be reproduced by anyone but this makes the whole situation much more clear.
Any feedback is welcome.
Cheers
It seems that my 8525 with Black Satin (WM6) has recently started crashing when I slide it close after sending a message or after sliding it open when recieving one.
The screen goes all dim and interlaced looking but it's really "off" as when I press the power button it actually boots up. When this happens that current text message is GONE poof!
I sat there and slid it open and closed 20+ times and couldn't repeat it but when trying to use it for real is when it freezes. It's not only with the text messaging though as I tried to slide it open to reply to a message on the internet (via wifi) and it locked up there also.
I did a search and haven't really found anything... guess I could reinstall but man, I hate having to do that... what all will I need to rememeber to back up? Text messages, phone numbers, settings for tomtom? bah!
Anyone ever experienced this?
Great, I think it's a loose connection somewhere... I noticed it was out and I had only put it down, not closed the slide. So just now when it was just idle I tapped on it and poof it locked up.
Great... Now what!
gilligan8 said:
Great, I think it's a loose connection somewhere... I noticed it was out and I had only put it down, not closed the slide. So just now when it was just idle I tapped on it and poof it locked up.
Great... Now what!
Click to expand...
Click to collapse
If it's still under warranty, take it in and have them look at it.
If it's not, look for one of the many disassembly instructions around, take it apart and reseat the cables.
I took mine apart not long ago to fix a non-working camera and it was amazing easy to get into the phone and remove and reconnect the cables.
Just make sure to read everything before trying it.
I bought it off ebay (supposed to be brand new) to unlock and use on a regional company's network. So doubt I'm covered.
http://pdasmart.zftp.com/instructions/Cingular 8525 Instructions.pdf
Is that a sufficient set of instructions? I'm not opposed to doing this, I repair laptops all the time and they are just about as difficult if not worse sometimes. I had attempted to take apart a friends dead 8525 a year or so ago but didn't know where the retention tabs were to get it opened beyond the obvious screws.
gilligan8 said:
I bought it off ebay (supposed to be brand new) to unlock and use on a regional company's network. So doubt I'm covered.
http://pdasmart.zftp.com/instructions/Cingular 8525 Instructions.pdf
Is that a sufficient set of instructions? I'm not opposed to doing this, I repair laptops all the time and they are just about as difficult if not worse sometimes. I had attempted to take apart a friends dead 8525 a year or so ago but didn't know where the retention tabs were to get it opened beyond the obvious screws.
Click to expand...
Click to collapse
That would be the basics. I noticed that it doesn't say anything about the tape for the large ribbon cable, so there may still be some snags if you use those (I don't know if the tape is present on all the various rebadges of the hermes).
Nice that they use a tool to take it apart, I used something like a debit card on mine.
If you are comfortable disassembling a laptop, you should be fine. As with a laptop, just take it slow and be careful.
(shudders at the memory of disassembling a compaq and Apple laptop)
Word, I hate working on laptops... but I guess I got to!
I'll bet it is the battery header on the board. I had a similar issue and needed to repair a solder joint there.
same here.. i was lucky it was still under warranty..
good luck with the dissasembly!
it has been rather calm lately... though I am a lot more gentle when sliding it open and close...
I know it couldn't have been a fluke... maybe some dirt got in and now is out... I'm sure I will have to get at it eventually... till then I'll just keep treading lightly!
Oh, and Mike, thanks for those links... VERY good stuff!
Lets say I am sick and tired of my 8525 turning off on it's on randomly during the day and I have loaded 10 different roms all the way back to the stock one, I have ran it with NO aftermarket programs, I have replaced the battery, and I have added support to the sim card to make sure it isn't losing contact and still the phone turns off randomly on it's on.
Sometimes I have noticed that it will turn itself off if I slide the keyboard out (maybe 3 times out of 100 turn offs), but 97% of the time it will do it on it's on sitting on the desk untouched.
If I was going to take my phone apart, is there any ideas or general consensus to what parts might be causing the phone to turn itself off? Should I get a new sim card maybe?
Really sick and tired of my buddy with an Iphone throwing this bug in my face telling me what crap HTC is as well as missing calls.
If the phone is turning all the way off, over and over, then send it in for a replacement. If you mean the screen is just turing off after a certain amount of time, you can adjust that under: "Settings->System (tab)->Power->Advanced->then uncheck Turn off device if not used for x minutes. See if that helps, or maybe its just ur phone and you need a replacement. I sent mine in to ATT and got one back after my screen stopped turning on"white screen of death", heh. So it could just be a hardware issue that you cannot really solve urself...
The phone is turning all the way off on it's on. I have to boot it back up like I had just installed a battery or something.
I am out of warranty and do not want to pay for a refurbished phone since this is my third phone from them during the warranty already (and this ones been the best till now). I would rather someone tell me the board/part and I take it apart and fix it myself. I have the tools, the instruction manual in PDF someone posted a while back, a website with almost every internal part for sale, and experience taking small devices apart (ipods and such) and replacing items, I just want to know if anyone knew of which part could most likely be the part causing something like this before I start replacing things blindly. I plan to go ahead and take it apart and check ribbon cables since I want to replace the whole housing anyway.
Unfortunately, my D900 has the same problem with yours, it turned off when i just sending messages or just touching the screen, and my replacement battery is already on the flight, when i get it, i will test it again. Hopeful, i can get a sweat result~~
Mine doesn't seem to do it when it is in use. I have had to get in the habbit of looking at the LED on the phone to make sure it is still turned on. Gets real annoying trying to say the Iphone isn't all that people think, but then have this little problem and the fact I am on my third HTC product in the year time frame. But the others died within 30 days, this one has lasted 10 months thats why I want to keep it.
Well I think I figured it out. I took it apart and it looks like the black box that has the battery connectors to it and is soldered to the main board has broken loose. I am trying to fix it, but does anyone know how much the main board is if I need to replace it?
guys - severe problem here
had my 8525 for 2 years or so and have had it insured thank goodness - two trips to the shop have been done already, one for the RED LED problem that i thought ruined my device.
now out of the blue yesterday the phone started shutting off on its own. seemingly randomly, at no specific times, it will just turn off, as if i held the power button down for 5 secs and hit ok.
it will only come back on if i hit the soft reset button or hold the power button and then it reboots. it is making life very frustrating as i'm missing calls and messages often because i have to constantly watch for the green LED to be on to know that the phone is still working
i have three accumulated three batteries over the years so i know thats not the problem, it occurs with all three.
anyone suggest anything before i send it back in? not excited to pay another deductible as i've already doubled the price i paid for the phone in insurance fees!!
My advice would be to do a complete backup, and then hard-reset. Assuming that the issue disappears after the HR, then restore from your backup. Hopefully, you will not restore the issue as well. If you do, then HR again, and DON'T restore from the backup ... install everything fresh.
HTH,
-pvs
There have been a few reports that the battery contacts can become less firm against the battery - causing random switch offs. This was easily solved by having a thin strip of card between the battery and the casing on the side opposite the contacts. Thus pushing the battery a little more firmly against the contacts. (Also make sure the contacts are clean)
Something easy to try at least.
Remember to search - here's one example:
http://forum.xda-developers.com/showthread.php?t=315591
Mike
thought of that halfway through the day today when i was fidgeting with it and realized there was a little bit of play in the battery compartment. actually put a thin piece of paper on the opposite side of the contacts and the phone has stayed on for an hour so far!!! sure hope that was the fix - would make me pretty happy - keeping my fingers crossed!
i had done a hard reset last night hoping for a fix but to no avail. thanks for the suggestion though.
the weird part is no jarring or dropping took place so i am surprised this issue arose out of the blue??
thanks for the help - and i did search but will look more thoroughly in the future
Hope it works long term - I wonder if thin paper is enough, we'll see.
Sorry about the search comment
Cheers
Mike
the weird part is no jarring or dropping took place so i am surprised this issue arose out of the blue??
Click to expand...
Click to collapse
Well, those spring contacts can get a bit tired and maybe a little oxidised and they loose the spring in their step - a bit like me really. I'm stuffing in the cream cakes however not slips of paper but I still randomly switch off from time to time, in fact more and more often!
haha - yea i suppose same goes for me!
however it stopped working =\ worked for about an hour and a half then i bent down to pick something up with phone in pocket and it died. seems like slightest movement would make a difference, but then later on it died at my desk again =\ thought i had found the culprit too
on the gold prongs, on the phone part, there is a tiny bit of evidence of melting on the black plasting holding the prongs. on either side of the black plastic where it meets the green board of the phones interior, there is a silver weld. on one side, it looks like the black plastic melted a bit and the silver weld is barely visible. the plastic is rough and not the same edge as the other side. that's the only noticeable difference
thought i had found a quick fix, but i suppose the last option is the old $50 deductible for the third time =\
Mmmm.. not good. However it seems it is a contact problem and there have been reports of that complete battery contact assembly coming off. Some have been successfully re-soldered, but in one case the contact was broken inside the mult-layered board.
I'm slightly puzzled about the melting - almost as if someone has previously been re-soldering it. (seems a little improbable that a poor contact at that ampage could cause enough heat to melt it - but I could be wrong)
Mike
mine was doing this and nothing fixed it apart from a reflash, its been working fine since i reflashed two days ago
hope this helps
Last night my Transformer started acting up. I was browsing Facebook, and then I hit the back case just right while setting it down and the screen went all green and purple (garbled/glitchy). I kept pressing it and eventually the screen completely shut off, though the backlight was still on.
In this small "how to", I will show you what you need to reconnect to get the screen back to operational status.
There are two sets of tear down pics for the TF that I found. One comes from XDA member hybridau, found here and the other is Tech Republic. I'll be linking to pics from Tech Republic along with my own as they were a little more informative.
Take the device apart. Torx T5 is needed for the bottom. Work your way from the end they show in the picture here. Then, press down hard (but be gentle ) on the side until the bezel disconnects from the base (pic). Next, gradually work your way around until you get to the dock connector. I used a thin piece of plastic to go around the edges, but I've heard a guitar pic works well (I don't own one). Note: for me, the dock connector was the most difficult part of the bezel to remove.
Remove the four screws around the screen area and then the three around both long sides (six total).
Turn the device over (screen facing down) and remove the back cover (pic).
Now, look for the piece in the pics below. The ribbon needs to be pushed all the way in where you can't see any of the connectors. Mine was visibly out of place. It won't be fully out of place. I used my fingernails to gently move it back into place one side at a time. You may want to try something else... it's not the easiest thing to move back since there is tape that was/is supposed to hold the thing in place.
Full device view:
That's it! I turned it on while it was apart to make sure screen worked, but that's up to you. Put it back together the reverse way... much easier putting it back together. I put the bezel back on the opposite direction I took it off.
Little background on the device:
The device has been dropped a few times while in a protective case or when tossing onto the bed (no visible signs anywhere on the device -- seriously, the device was thrown and dropped more during shipping than it was in my possession), so I called ASUS and they issued an RMA on it. Of course, if the issues are caused by you (dropping), you have to pay. Regardless, shippings going to cost some money.
Thus, I took it upon myself to fix it. I knew it had to be a ribbon that was disconnected because I doubted it was any kind of screen problem. I had also read in another thread here that that when they sent their TF off the return said all the techs did was reattach the ribbon. What a waste of time, money, and effort?!
Anyway... hope this helps someone with the same issues I had!
Thank you very much for the details. It doesn't effect me but I have read several threads where people are having this issue. I am asking a mod to sticky this for awhile so it doesn't get lost
Thanks! I just hope it helps someone else contemplating doing what I did. I almost wasted time and money sending it to Texas for repairs!