Hd2 bricked I think.. - HD2 Windows Phone 7 Q&A, Help & Troubleshooting an

Hello my brother bricked my tmous hd2 he was installing Wp7 from Android and through the installation the device just shut down don't know why ....,
The battery was 100%,after manual restarting the phone it shows white screen and
with colors around on top and down of the screen, cannot enter bootloader.
Help please want to revive this piece of beautiful Tech

3abdo3asal said:
Hello my brother bricked my tmous hd2 he was installing Wp7 from Android and through the installation the device just shut down don't know why ....,
The battery was 100%,after manual restarting the phone it shows white screen and
with colors around on top and down of the screen, cannot enter bootloader.
Help please want to revive this piece of beautiful Tech
Click to expand...
Click to collapse
Were you with him when it was bricked? Are you sure it went off on its own?
(because as far as I know, the HD2 won't shut off for no reason, taking into account that the battery was fully charged.)
Also, since the device boots up, I doubt it is bricked.

If you have HSPL on it, than it is not bricked.
Try this:
1) Take out the battery for 30 sec at least
2) Put it back in and press the volume down button (and hold it), while you press on the Power button (an hold)
Until you enter the 3 colour screen
After you are there, just connect it to the PC and as soon as it says USB you can flash MALGDR or anything you want.
Good luck.

ughhh
man i think my hd2 is brickd like it wont even turn on it only vibrates a lil wen i press the power button any help please

Johev said:
If you have HSPL on it, than it is not bricked.
Try this:
1) Take out the battery for 30 sec at least
2) Put it back in and press the volume down button (and hold it), while you press on the Power button (an hold)
Until you enter the 3 colour screen
After you are there, just connect it to the PC and as soon as it says USB you can flash MALGDR or anything you want.
Good luck.
Click to expand...
Click to collapse
sereousl said:
man i think my hd2 is brickd like it wont even turn on it only vibrates a lil wen i press the power button any help please
Click to expand...
Click to collapse
When it vibrates, isn't it a sign that it's booting up? Try doing what Johev stated. Hold the Volume down button while it's booting up or even while holding the power button. If you can get to the tri-colored screen, your phone is safe.

Related

X2 - Can't enter bootloader mode?

Hi, I am having an issue getting my X2 into boot mode in order to update the firmware - even following the instructions on SE Update Service (press and hold volume down button and power button until white screen appears)
All that happens is the vibration feedback to indicate power on, then the phone loads up as normal.
I've updated another X2 and it worked correctly, the problem appears to be with this specific unit.
Does anyone have any suggestions on what may be causing this, or how to get this one into boot mode please?
Best to send it to service centre..
could it be because it's made in china? just a thought...
Just note that on the X2 you wont see the bootloader.
You know your in the bootloader when the phone stand on the SE Logo.
Then you can connect the phone and update it
Hi, thanks for the advice all
I can't send it to a service centre as I don't have a receipt unfortunately
I'm not sure what being built in China has to do with it not entering boot mode, most SE phones are and I've not had a problem with my other ones?
Thanks for the advice on boot mode - I successfully used SEUS an another X2 and the boot mode is essentially a white screen with the SE brand logo - sadly I don't get that white screen just the black screen with logo and vibration feedback then it powers on.
Any other suggestions or should I give up and sell as faulty/parts only?
Thanks
nonentity said:
could it be because it's made in china? just a thought...
Click to expand...
Click to collapse
And the X1 was made in Taiwan. What's your point?
bootloader phone stand on the SE Logo
hm, obviously missed that one after X2 subfora where created...
Mod. edit: moved to correct forum, X2 General
try this:
read all steps first
turn off phone
pull out battery wait ten seconds
put battery back in (leave cover off)
hold the power button + hold volume down
press the soft restart button* (while still holding the power button + volume down)
keep buttons held down till you see the white screen and green logo.
note* push the button with stylus it is hidden under where the stylus goes in next to the camera.
plug into the computer and run SUES it'll say already have latest version update anyways? click yes
i had to do this when i bricked my phone, (my computer crashed while i was doing the update) it really saved my day.
x2 dead
I have same problem in my phone , during update with SEUS computer hang and now
my phone shows only vibrate.
i have tried volume down+power+reset
but it can't go to white screen or sonyericsson logo.
any other solution
harveydent said:
And the X1 was made in Taiwan. What's your point?
Click to expand...
Click to collapse
his point is if this Xperia is the one that's fake.. the one from China..
10X
yummy-fun said:
try this:
read all steps first
turn off phone
pull out battery wait ten seconds
put battery back in (leave cover off)
hold the power button + hold volume down
press the soft restart button* (while still holding the power button + volume down)
keep buttons held down till you see the white screen and green logo.
note* push the button with stylus it is hidden under where the stylus goes in next to the camera.
plug into the computer and run SUES it'll say already have latest version update anyways? click yes
i had to do this when i bricked my phone, (my computer crashed while i was doing the update) it really saved my day.
Click to expand...
Click to collapse
10x dude. u saved my x1
extracted rar archive directly in task29 folder, dono how, but didnt replace the ruu_sign.. and flashed whit the 3MB ruu file in the folder..
i found your post 1st, and managed to boot and install from sd.. many 10x

[Q] help in un bricking my tmo-hd2

Hi guys, i am facing exact same thing which dannytgt faced (http://forum.xda-developers.com/showpost.php?p=6707785&postcount=1)...but with no luck what so ever.....was running a stock rom in my hd2 3.14....wanted to try wp7 and did a task29....after that...hd2 doesnt go into bootloader screen....tried all possible combinations with/without sd,sim, holding vol down, vol up, both with power tapped...power holded etc etc...hd2 always goes into stick together screen and doesnt progress as there is os to load....opened up the mobile and tried with a pin to push the vol down switch directly also....all hardware keys were working gr8 (including vol down and up and power keys) whn win 6.5/android was running.
i know for the fact that this is reversable....if only my hd2 can get to bootloader...i will hv os running in a jiffy....
any ideas ppl? my hd2 is 3 months old ...no warrenty cos i bought it in US and using it in india...
bootloader dont load
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
resolved the problem myself.....hd2 is working like a charm....thanks for all your support.
gdsbalaji said:
resolved the problem myself.....hd2 is working like a charm....thanks for all your support.
Click to expand...
Click to collapse
Good to know it got resolved. What did you do? In my case I had kept the battery out for a while and put it back in and it started getting me into bootloader with VOL down and Power key.
nicedude_abad said:
Good to know it got resolved. What did you do? In my case I had kept the battery out for a while and put it back in and it started getting me into bootloader with VOL down and Power key.
Click to expand...
Click to collapse
Good to know you got it working.
SOLVED {bootloader dont loadArrow}
checkout the solution for my problem here....might help u as well.
http://forum.xda-developers.com/showpost.php?p=10644926&postcount=4
______________________________
if you feel this helped...thank me

HELP!!!

Hi, I recently installed TyphooN CyanogenMod 7 v2.3.3.. I was texting yesterday and it randomly restarted by itself...it usually does that once in a while so i ignored it. However, this time, it kept restarting non-stop and my android won't boot, so i decided to install v2.4.1 on my phone since it was in my SD card anyway... now when I try to turn my phone on, it just vibrates CONSTANTLY non-stop with a blank screen until I pull the battery..
I tried letting it vibrate till the battery died but its still the same thing. When I connect it to the wall charger, it seems like nothing happens.. when I connect it to the computer, its the same thing as turning the phone on..
Please help, I am phoneless right now,
Thank you
Unplug your phone from charger than press and hold Volume Down button and turn the phone on.
The phone should boot into bootloader mode.
Now connect it to the PC with USB cable and flash WM ROM.
After you can start all over again and flash Android back.
ryennn said:
Hi, I recently installed TyphooN CyanogenMod 7 v2.3.3.. I was texting yesterday and it randomly restarted by itself...it usually does that once in a while so i ignored it. However, this time, it kept restarting non-stop and my android won't boot, so i decided to install v2.4.1 on my phone since it was in my SD card anyway... now when I try to turn my phone on, it just vibrates CONSTANTLY non-stop with a blank screen until I pull the battery..
I tried letting it vibrate till the battery died but its still the same thing. When I connect it to the wall charger, it seems like nothing happens.. when I connect it to the computer, its the same thing as turning the phone on..
Please help, I am phoneless right now,
Thank you
Click to expand...
Click to collapse
rikardo1979 said:
Unplug your phone from charger than press and hold Volume Down button and turn the phone on.
The phone should boot into bootloader mode.
Now connect it to the PC with USB cable and flash WM ROM.
After you can start all over again and flash Android back.
Click to expand...
Click to collapse
I held the Volume Down button and pushed power key...it just vibrates until I pull the battery
ryennn said:
I held the Volume Down button and pushed power key...it just vibrates until I pull the battery
Click to expand...
Click to collapse
Try this...Pull & keep d battery out of d fone for abt 2 mins..then pop it back in..
Enter bootloader mode..
Perform a Task29...the one by "doloop" wipes ur phone memory clean without affecting ur previously installed HSPl or Radio...
Re-Flash a rom of ur choice.
voncrane said:
Try this...Pull & keep d battery out of d fone for abt 2 mins..then pop it back in..
Enter bootloader mode..
Perform a Task29...the one by "doloop" wipes ur phone memory clean without affecting ur previously installed HSPl or Radio...
Re-Flash a rom of ur choice.
Click to expand...
Click to collapse
i kept the battery out for the entire night, put it back in this morning, pushed the power button and same exact thing.. ]:
Might sound really obvious but try hold in the little reset button on the back of the phone for like 10secs and see if anything happens. I had the WSOD and looked everywhere for a fix then I just did that and it worked. Goodluck.
Skellyyy said:
Might sound really obvious but try hold in the little reset button on the back of the phone for like 10secs and see if anything happens. I had the WSOD and looked everywhere for a fix then I just did that and it worked. Goodluck.
Click to expand...
Click to collapse
Nothing happened... ]:
I left the phone on vibrating until the battery died... Charged it and left it out of the phone this morning until now and the phone won't even turn on when I press the power button now....It just doesn't even respond :|
Kick your phone in the nuts and try again
I wish it was that easy ):
You can't go to bootloader? What radio version u are use?
HD2 TMOUSA
rom : TyphoonCyanogenMod 7
radio: 2.15.50.14
LINTEAM LEADER(gpu dev)
Keep your phone off.
Hold Both the Vol up and Vol down buttons and then press the power button...
That'll let you do a hard reset.
Not sure if it'll help... but can it do any more harm?
My phone doesn't even turn on anymore.. I can't get into bootloader.. it doesn't charge either..
Well, its look u really fcuked the phone.
I know this really not help u at all
U have 2 options
1st one take it back to shop if u still under warrenty
2nd take it to some repair center where can be repaired with JTAG method
I know u didn't want to hear this but its look its nothing more u can do with it.
Good luck to u m8
ryennn said:
My phone doesn't even turn on anymore.. I can't get into bootloader.. it doesn't charge either..
Click to expand...
Click to collapse
I sent an email to HTC today..hopefully I can fix this... I had HSPL installed so it voids my warranty if I send it back correct? ):
Anybody else heard of this problem? ):

[Q] hd2 died?

i was charged my hd2 and it never waked up.only a black screen.anyone can help me?
Wrong section. please move this thread to the Q&A section.
Have you tried removing battery?
When this thread is moved (and it surely will be moved) the people that will try to help you will need more information than "i was charged my hd2 and it never waked up."
What happened?
What were you doing at the time? Did you try to put a new rom on it?
What did you do to try and 'fix' it?
yes but nothing.i wasnt do anything.i just put my phone for charge.when i tried to open it it didnt worked.just a black screen.i tried the red button the up volume way but nothing.
leoncupra said:
yes but nothing.i wasnt do anything.i just put my phone for charge.when i tried to open it it didnt worked.just a black screen.i tried the red button the up volume way but nothing.
Click to expand...
Click to collapse
Hi,
Take the battery out,then put it back in,switch on,and hold the down volume button.
Does it boot into bootloader(tri-color screen)?
sorry for putting the post in wrong place.it never happen something like this before.when i had wm i did a soft reset or removing the battery and everything was ok.now i dont know what happent.and all i did was to put the phone to the charger
no my friend.dead
malybru said:
Hi,
Take the battery out,then put it back in,switch on,and hold the down volume button.
Does it boot into bootloader(tri-color screen)?
Click to expand...
Click to collapse
You have to hold the volume down button AND the power button at the same time in order to get to the screen with the three colours (bootloader screen)
nothing.it seems like the buttery to be dead.maybe is butterys problem?or there is a chance the screen to be burned?
If you can get into bootloader then all is not lost - get out of there and direct your browser to this link:
http://forum.xda-developers.com/showthread.php?t=1090783
Read carefully before continuing. I suggest you start with a wipe (task29) then install MAGLDR - BUT ONLY IF YOU HAVE ALREADY PLAYED AROUND WITH NAND ROMS. If your phone is still a Windows Mobile device rather study this section before you do ANYTHING!
http://forum.xda-developers.com/showthread.php?t=905841
And one final word of warning - if you still have your phone under warranty (or it is insured), take it back to the shop to have it fixed before you do anything that could void this.
...and maybe it is as simple as the battery just died?
i cant get into bootloader.the phone is dead.i have to try a new buttery and we'll see.thanks anyway
DeeinSouthAfrica said:
You have to hold the volume down button AND the power button at the same time in order to get to the screen with the three colours (bootloader screen)
Click to expand...
Click to collapse
Funny,
mine goes to bootloader without having to hold the power button down.
@[OP]
Did you manage to charge the phone at all?
Do you have a spare battery or battery charger?
Are your pins bent?
If your battery is dead and you cannot charge it,try this:
http://forum.xda-developers.com/showpost.php?p=15052987&postcount=5

[Q] Can't start phone?

Hi All,
I need your quick help, I dont know why but I cannot start my Samsung focus v1.3.
I tried to flash it by pressing power button + volume down + camera button but can't do hard reset.
When I am trying to remove battery and reattach battery again, then phone just showing "SAMSUNG" screen and again goes switched off.
Even I tried to press power button + volume UP + camera button then it shows only "Download Mode" screen only nothing happens after this.
Please need your help!
Many thanks in advance,
Since you just flashed it, I assume that it started up by displaying 'SAMSUNG" and seems to be stuck there.
If that is the case, you need to be patient. It takes a few minutes to get past that point. Every time I flash, I feel like I have done something wrong and the phone is bricked. But it always moves past that point after a few minutes.
wildbilll said:
Since you just flashed it, I assume that it started up by displaying 'SAMSUNG" and seems to be stuck there.
If that is the case, you need to be patient. It takes a few minutes to get past that point. Every time I flash, I feel like I have done something wrong and the phone is bricked. But it always moves past that point after a few minutes.
Click to expand...
Click to collapse
Thanks for your reply,
But I haven't flashed my phone..
and from yesterday it is showing same 'SAMSUNG' name screen and then again goes switched off..
dont know what is going wrong.. or is it due to battery issue?
please help!
nah, it's the power button switch which somehow got stuck, it's a relatively common issue with the focus it seems
some people have reported that cleaning the button helps, others simply have replaced the whole switch at a local repair center... do what you think is best
Saiyaku said:
nah, it's the power button switch which somehow got stuck, it's a relatively common issue with the focus it seems
some people have reported that cleaning the button helps, others simply have replaced the whole switch at a local repair center... do what you think is best
Click to expand...
Click to collapse
Thanks Saiyaku,
But how power button works when I press (Powerbutton + Volume UP + Camera button), screen shows me "Download Mode" nothing happens after that. Yesterday whole I tried these options..
help
To flash magldr, you need that combo , press power button + volume UP + camera button then it shows only "Download Mode". To flash a ROM, you go Vol DOWN, and then reset your phone, or format, and then go back to the same menu, and when you see the do you want to format your phone stuff, you hit the back button and you'll see the magldr screen where you'll connect your USB and go forward with the flashing process. Perhaps try flashing an actual ROM to your phone. You can't really do squat from from the download screen but add magldr really. Hope that helps you.
Please need your help!
DACHEF81 said:
To flash magldr, you need that combo , press power button + volume UP + camera button then it shows only "Download Mode". To flash a ROM, you go Vol DOWN, and then reset your phone, or format, and then go back to the same menu, and when you see the do you want to format your phone stuff, you hit the back button and you'll see the magldr screen where you'll connect your USB and go forward with the flashing process. Perhaps try flashing an actual ROM to your phone. You can't really do squat from from the download screen but add magldr really. Hope that helps you.
Please need your help!
Click to expand...
Click to collapse
Thank you for your comment, but I haven't installed magldr.
[email protected] said:
But how power button works when I press (Powerbutton + Volume UP + Camera button), screen shows me "Download Mode" nothing happens after that.
Click to expand...
Click to collapse
because download mode disables the power switch (it even says "do not turn off"), that's why it seems to "work". power switch is active at the format prompt, however, so when you enter that mode the phone turns off immediately afterwards
do a little experiment: remove the battery, then put it on again while you're pressing volume down plus camera... you'll probably see a little surprise there
it's the switch. go repair that nao
i have the same problem, and many unfortunate people out there , but my phone on service center now, and i just wanna tell you about this thread this http://forum.xda-developers.com/showthread.php?t=2007946, maybe can make you calm for a while... look at his problem solution

Categories

Resources