Like my guide? Support me via donations: [email protected] and I'll continue writing more guides on whatever you ask me
It took me a lot of research to finally get my tab updated and rooted...between hearing about the locked bootloaders and such, but now...I am going to give you my guide to success...
Step 1 - Prereqs
Download this file Root Files
Extract folder to desktop and install driver's if you don't already have them installed.
Connect your tablet with ADB (Debugging) turned off (Ensures it is in MTP mode)
Step 2 - Copying files
Copy eh04_update.zip (If on EG04) and Galaxy_Root to your tablet
Step 3 - Updating to EH04 (If on EG04)
Completely power off your tablet
Once off, turn it on, when you see the screen light up, HOLD power+vol up until you see two icons
Press Vol up then press Vol down - You will be brought into the recovery menu.
Press vol down until you are highlighting "Apply update from /sdcard" then press power to select
Press vol up until you are highighting "eh04_update.zip" then press power to select
Tablet will update - this will take around 5 minutes and it will reboot on its own
At this point you are updated to EH04 and can stop here if that's all you wish to do...Below I describe how to root the device.
Step 4 - Installing Clockwork Recovery
Completely power off your tablet
Once off, turn it on, when you see the screen light up, HOLD power+vol up until you see two icons
Press Vol Down and when prompted press Vol Up
If not already, plug the tablet in, install drivers if you didn't listen in step 1
Open Odin from the folder Odin.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Click "PDA" and select "ClockworkRecovery_LTE.tar.md5" from the folder you extracted
If Odin does not show your tablet plugged in (yellow box with a COM port number) make sure your drivers have installed properly.
If everything checks out - Click "Start"
Once It has finished writing, the tablet will restart
THIS PORTION IS COMPLETED! You now have Clockwork Mod installed
[I'll finish it up tomorrow, I'm beat from no sleep]
Thanks for spending the time to write this up. I've been through the process twice now, but it'll be nice to be able to reference this directly whenever I need to go through again.
xenokira said:
Thanks for spending the time to write this up. I've been through the process twice now, but it'll be nice to be able to reference this directly whenever I need to go through again.
Click to expand...
Click to collapse
Thanks for the inspiration
Posted the link for the files - Should get you start!
Related
i bought this for christmas and the dude gave it to me like this. everytime i cut it on it goes to this screen. what is this ? how do i get back to regular stock os ? thanks !
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
It's fine, this is Windows Default . You just have to switch to Sense.
To do that just press Start Button --> Settings --> Home --> *Switch to Items* --> Make sure "HTC Sense" Is checked and "Windows Default" Isn't .
There's nothing wrong with that - it's the Windows Today screen. I'd recommend doing a hard reset since you just got it.
Turn off the phone, hold down both volume down and volume up buttons, and briefly press the power button. Then follow the on-screen instructions.
Sent from my HTC HD2 using XDA App
delayynee said:
i bought this for christmas and the dude gave it to me like this. everytime i cut it on it goes to this screen. what is this ? how do i get back to regular stock os ? thanks !
Click to expand...
Click to collapse
Based on the pics, I guess you need to flash a new rom since it looks like a chuckydroid rom.
Sent from my HD2 Droid using XDA App
Its either a stripped own windows designed for using as a base to boot into Android OS, or it has had sense disabled via settings.
Go download the windows ROM you want as your OS, extract the .nbh file, rename it to "leoimg.nbh" put it onto root of your sdcard and reboot phone and then hold volume down key and follow instructions.
TheATHEiST said:
Its either a stripped own windows designed for using as a base to boot into Android OS, or it has had sense disabled via settings.
Go download the windows ROM you want as your OS, extract the .nbh file, rename it to "leoimg.nbh" put it onto root of your sdcard and reboot phone and then hold volume down key and follow instructions.
Click to expand...
Click to collapse
i put the leoimg.nbh file, nothing happened. it booted back to the same screen.
do i click power, THEN vol down ?
i also left all of my other files up there.. will that interfere?
Place the downloaded leoimg.nbh on the root of your memory card, hold down vol-down button and then hold down power-button until the screen wakes up. If you have done it rigth, instructions should appear and you just follow them...
These are the steps explaining you how to flash a custom firmware to the SmartQ Ten3 T15.
Use my How To to create the Custom Firmware.
These steps should apply to any custom firmware for SmartQ Ten3 T15.
Warning : Creating a firmware and changing the files may cause your device to stop working, I won't be held responsible for any damage caused by this.
Flashing your firmware isn't more difficult than rooting the device, if you did that you can do this.
I'll use pictures to illustrate the right options. The recovery is in Chinese so this will make it easier to follow the right procedure.
1. Reboot your device into recovery, by selecting the right option in Android 4.0.3 after long pressing the power button. Or by pressing and keeping the volume down button together with the power button.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
You use the volume up and down buttons to move the selection up or down. And you press the power button to confirm an option.
2. Select the second option from the menu. (Flash file from SD card)
3.Select the 3rd option from the menu. (Toggle certificate verification)
An extra line will be added to the bottom half of the screen. Most probably confirming the toggle to switch off certification verification.
4. Select the 2nd option from the menu. (Browse sd card for file)
5. Select the file SmartQT15 you put on the root of your microSD card.
Firmware flashing will start and you can follow it's progress in the lower half of the screen:
Once done the last menu will appear again.
6. Select bottom option from the menu. (Back)
7. Select the top option from the menu. (Reboot device)
Firmware flashing is done and your device will reboot. If you have done nothing wrong your device will start-up normally.
If you have any questions feel free to post below and I'll do my best to answer them, all the above is based on my experience and from what I could find out on the Internet.
If you want to know how to make the firmware pre-rooted contact me via PM and I'll do my best explaining it to you.
Hello everyone!
i do the following step how to install Nanandroid on my HTC Touch HD.
1. Flash the latest HardSPL from OliNex
2. Extract the 'adb files & fastboot.exe' files to a folder
3. Format the microSD card fully as FAT32
4. Copy the 'BlacIMG.NBH' file and your selected ROM (zip) you wish to use to the root of the microSD
5. Boot in TriColour mode (Power button and Volume down button)
6. Whilst in the TriColour mode, connect the Blackstone to a USB port ('Serial' should now say 'USB')
7. Run 'BlackstoneRUUAdvanced' and select the 'Task 29' which is full wipe of the Blackstone
8. Once completed, insert the microSD card and reboot into the TriColour mode again
9. The Blackstone will auto-flash-install (after key confirmation) the 'BlacIMG.NBH' on the microSD card
10. The 'BlacIMG.NBH' must NOT be flashed via Windows using the RUU tool (it will only fail)
11. Once flashed with the 'BlacIMG.NBH' it will reboot to a new Fastboot screen (blue background)
12. After a short time the Blackstone in Fastboot mode with enter a USB connect ready state
13. Now connect the Blackstone to your Windows OS and open a CLi/Command prompt
14. Within CLi go to the directory where you place the 'adb files & fastboot.exe' files (from step 2)
15. Type: fastboot flash recovery recovery.img (this will flash install the custom CWR)
16. Then type: fastboot boot recovery.img (this will reboot your Blackstone into CWR)
and it's appear :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
then i chose apply from sd card. but it's stuck.!!!!!
would you help me, please!!! :crying:
thanks in advance.
Why did you make a new thread for this? God, for some reason there is a thread for the ROM already...
Anyways, the phone is not stuck.
When you get into recovery press vol up, down, and up again, as it says on the instructions. Please read before asking.
unlock the power botton
mfsr98 said:
Why did you make a new thread for this? God, for some reason there is a thread for the ROM already...
Anyways, the phone is not stuck.
When you get into recovery press vol up, down, and up again, as it says on the instructions. Please read before asking.
Click to expand...
Click to collapse
dude, try press up, down and up
strictly abide these three steps, you can unlock the power botton
Hi all,
I bit the bullet and picked up a 2nd hand OrangeUK Flipout (details available if I need to prove I bought it legally)... but the seller cannot remember the pattern to draw to access the phone.
How might I resolve this issue, please?
I can access the Bootloader, which is on v91.10, but that's all I've found so far.
I have found RSD Lite v5.6 and the USB Drivers from the MotoDev website.
Will flashing RUTEM_U3_01.19.2 (or any other RUTEM) onto the device ie following the Debranding Guide, reset this and allow me to start playing with Android?
What about the FlipOut Recovery?
Thank-you,
Dylan.
Wow. Err, okay, I wasn't expecting it to be that easy.
It only took a simple Hard Reset and it's fine - Back to the start as if seting up a brand new out-the-box phone!
In case any other fellow Noobie-Noobs encounters this issue, here's what I did:
Motorola Flipout (MB511) - Step by step hard reset
1/. Switch the device off - Hold the power button for a couple of seconds and then press Power Off
2/. With the device off, open it up, hold the X key and hold down the Power button until you see the Motorola M.
3/. Shortly after, an image like this will appear:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4/. TAP the power button to enter the Android System Recovery menu.
5/. Use the little D-Pad to select the 4th option - Wipe Data/Factory Reset.
6/. Press Enter to confirm.
7/. Confirm you want to reset the device.
8/. After the reset, go back into the System Recovery menu and select the 1st option - Reboot.
You should now have one factory-fresh phone!
Gratefully translated from Portuguese instructions at the EIL forum!
Hello.
At the beginning I want to say that English isn’t my primary language and I apologize for mistakes. I hope this text will be understandable.
I have problem with my LG P710 [L7 II].
Few months ago I have tried to upgrade it using LG_KDZ_FW-Update.
I have started to look for the best software for me and after a long time I found software which include root and CWM Recovery… wow.
Instalation wasn’t completed successfuly. From this time I can run my device only in Emergency Mode. No matter if I connect it to the USB, battery charger or just press button to turn it on.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I don’t know I did something wrong, the instruction was bad or maybe soft was demaged.
I have another cell phone so it wasn’t urgent to repair it then, but now I think it’s time to do it!
I hope you can help me with that.
I’m trying to do it this way:
• Download and install drivers [LGMobileDriver_WHQL_Ver_4.0.3]
• Download and install update tool [LG_KDZ_FW-Update_OfflineFix]
• Download software [V20A_00.kdz]
(I’m working on Lenovo G510 with Windows 10 installed)
• Change hosts file [C:\Windows\system32\drivers\etc] by adding at the end:
127.0.0.1 csmg.lgmobile.com
• Install B2CApp [setup file is inside LG KDZ FW Uptede Toll folder]
• Then I’m opening Automatic Offline Procedure script.
• Few windows appears on my screen. At this time I have Windows Enabler On and Small Server is running.
• After that script starts R&D test toll, I set Phone Mode [Emergency], select my .kdz file and
press Normal Web upgrade test, then on next window Upgrade Start.
• Afterward I clear Software Update Registry, select my language and press on OK.
• Phone Update window appears. Analysis done, download as well, but update stops at 4%.
According to the instruction I disconnect mobile, remove battery and connect it again with pressing Vol- (In order to enter Emergency Mode I guess. I’m lucky guy, I haven’t to press anything, my phone always turn on into Emergency)
• No change after clicking restart. 4% is everything I can get.
ctrlv.it/id/2452/3915649230 - Logs
If you know what is wrong, you have any advice, please help.