Hello Everybody, I will be very grateful if someone help me deal with my problem.
I have been on Android rom with my hd2 phone since a year ago and decided to try the clockworkMod recovery about 3 days ago but it does not seem to work so i followed so many videos on utube as I was getting frustrated.
I have already installed magldr v1,13,
Hi guys, I am seriously in need of your help. On my HD2 phone, I think I have managed to install clockwork Mod recovery v 3.0.0.5 but can't install a ROM on the sd card. After flashing and trying to install a rom from the sd card, "message on my phone was", finding update package.....
Opening update package.....
E: can't open/sdcard/Typhoon cm7 v3.6.8 clk.zip is bad.( I am not sure if I installed the correct rom)
I have also tried following several video links but still no luck.
-I have tried to format my sd card several times
-wipe cache partition
-wipe data/factory reset
-wipe Dalvik cache
I am currently stuck and don't know what to do again.
I already have on my phone, HSPL: 2.08, Radio: 2.15.50.14 and Magldr: v1.13
After trying several tricks, I have realised that, I cannot boot into magldr any more.
Any help guys?
Folow steps:
- install HSPL: 2.08 and Radio: 2.15.50.14 (read all about installing hspl or your device will be bricked!!!)
- if you have activesync installed, right click on activesync/connection settings, untick "allow usb connection"!
- download mtty.exe to your computer
- switch your phone to spl screen (volume down + power)
- connect your phone to usb/computer
- run mtty.exe, chose "usb" (if you not see usb, something is not ok), if you see usb, press enter (if you see mtty> ...etc all is ok, if not -> repeat until you make mtty conection with your phone)
- in mtty window type: task 29 and press enter (it will format your romfs)
- in mtty window type: task 2a and press enter(it will format your romfs and relocate bad blocks)
- done, you formated your romfs -> exit mtty
- in activesync enable again "allow usb connection"
- go to folder MAGLDR113_DAF
- run ROMUpdateUtility.exe and wait until you have done installing magldr
- restart your phone and press power button until you see magldr menu
- sellect usb flasher in magldr menu
- go to folder clockwork and use proper cwm for your rom and run daf.exe
- done
Next step:
- download free version of the MiniTool Partition Wizard and install it in your computer
- format your sd card with MiniTool Partition Wizard (1x primary/fat32 , resize: do not forget to leave 1gb space for the an ext2 partition) (1x primary/ext2), apply changes ...done)
- so you have 2 primary partitions on your sd card (1x fat32 1x ext2)
- coppy rom.zip to your sd card and reboot to magldr (press power and wait magldr menu)
- select ad recovery, go to install rom from sd card, select "chose image from sd card", install, ...done, reboot
NOTE:
some roms not working if your sd card not have an ext2 partition of the 1gb!!
I am not 100% sure, but I am new to hd2 device, for magldr version you need magldr rom...
Hello, thanks for your quick reply. I will try all the steps and hope it helps me.
Sorry, I forgot to ask you where to download the mitty.exe file from and is there a particular version to download?
Thanks.
http://forum.xda-developers.com/showthread.php?t=371154
YawTakyi said:
I have already installed magldr v1,13,
.......
E: can't open/sdcard/Typhoon cm7 v3.6.8 clk.zip is bad.
Click to expand...
Click to collapse
more importantly, you have magldr but have downloaded teh cLK version of typhoon. no need to reflash anything. (cLK is an alternative to magldr, and requires a slightly different build rom, thats why there are two versions of most roms.)
Redownload teh correct version and it will flash, , probably no need for the 'ohyougottadoatask29standononelegreformateverythingreturntostockreapplyhsplflashanewradioreinstallwindowsgetanewpcandreflash' doomsayers though i suspect its too late and you already started. hehe.
You can´t Flash clk over magldr. Go to the site/post and Download the magldr version
And when you stil have problems and nothing works for you try a different Sd card.
Hi munjeni,
Thanks a lot, I have managed to boot into magldr and even tried to intstall clk typhoon cyanogen Mod 7 nightly v3.6.9 and tried both the MAGLDR and CLK but it failed. I had an error message after I have rebooted "nand kernel open failed"
I had earlier installed MAGLDR 150MB system/ 5MB cache clockworkMod Recovery V3.0.2.5 (Is this the right Recovery to install?)
I am just confused and don't know what to do again.
Now that I can boot into magldr how do I proceed from there?
Thanks for your advice;
YawTakyi said:
I have managed to boot into magldr and even tried to intstall clk typhoon cyanogen Mod 7 nightly v3.6.9
Click to expand...
Click to collapse
Again, try the Magldr version. Big ups. Let us know.
I am stuck after the error message "nand kernel open failed" I don't know where to start from...any ideas?
You should be more detailed. When does it say failed? When you try start cwm? Or after you flash the rom?
Get correct magldr rom
Enter magldr
Option 8-ad recovery.
If that's where it gives failed, go back into magldr, "USB flashing" and re apply cwm.
Once in cwm, choose wipe data/factory reset then "install zip from SD - choose zip" and select the typhoon zip.
Report back.
Related
i want to flash android back after i used the wp7
well i formated my sdcard and pushed recovery files with usb storage in magldr then i found i cant boot into recovery!
it dead at gogogo screen
and another interesting thing is if i translate zip system file with magldr
the file can not be used to update, neither (dead at 2nd boot screen)
and is this the magldr issue ?
sorry for pool english :S
Dear everyone,
I have a problem with my HD2 and it is very strange. I am not sure this is because of the hardware or the program or HSPL or Radio.
I can flash HSPL 2.08 now and can flash any rom with enter bootloader successful.
But it was stuck on green HTC logo during boot very long minutes. I must to take off the battery and put in again to try power on. I do this 2 or 3 times and then the window screen come and setup as instruction. It will auto turn off and restart again the stuck green HTC logo.
I decide to flash the Android 2.3.4 (NexusHD2 v2.8 NAND) by install cLK CWM. I did it successfully but it was stuck 1 time during I press HOME button to enter fastboot. The Android run so good and it was stuck again only when I turn off the phone or change SIMCARD.
Anyways, when I flash the stock rom (download from HTC website) via SD it was restart 1 time during 5% (maybe) and try to flash itself until finish. but I cannot boot it after flash just only show green HTC logo.
If I flash with Custom_RUU, it work perfectly by enter bootloader mode. and I can boot it but try 2 or 3 times because of stuck the green HTC logo.
Any body comment. Please welcome!
Or my HD2 has any problem with hardware?
Thanks.
Start again doing a task 29, then flash radio, then magldr, then clockwork then install androidbuild.zip using clockwork method and report back
Sent from my HTC HD2
whynot66 said:
Start again doing a task 29, then flash radio, then magldr, then clockwork then install androidbuild.zip using clockwork method and report back
Sent from my HTC HD2
Click to expand...
Click to collapse
Dear Whynot66,
Thanks for your comment, I will try to do it.
I am not sure will it run with magldr or not because last time it did not boot to MAGLDR after flash it.
I will report soon.
Hi, the below is what i have done.
1. Flash MAGLDR
o Download MAGLDR 1.13 (606 KB)
o Enter SPL by holding VOL DOWN key while booting the phone. (Make sure you have HSPL.)
o Run ROMUpdateUtility.exe to flash MAGLDR 1.13 (magldr.nbh).
2. Flash ClockworkMod Recovery
o Download MAGLDR_CWM_Recovery_v3.0.2.5_for_NexusHD2_135M.zip (5.1 MB)
o Enter MAGLDR 1.13 by holding power key while booting the phone, and then select "USB Flasher" via "VolUp" and "VolDown". Confirm key is green "Call" button.
o Run DAF.exe to flash ClockworkMod Recovery 3.0.2.5 (MAGLDR_recovery_3.0.2.5.img).
3. Flash Android ROM
o Enter ClockworkMod Recovery when you're on MAGLDR 1.13 (hold "Power" button during boot) and select "AD Recovery" or "Boot AD SD" (if ever copied CWM's initrd.gz and zImage to SD).
o Flash NexusHD2-Gingerbread_V2.7_NAND_(Android-2.3.4)_update.zip (84.51 MB)
I can do anything but stuck in ClockworkMod with the black screen and green HTC logo for long minute.
What can I do now? but it would be working with cLK flash.
This is becuase of hardware?
Thanks.
Oh I can flash now when select "AD Recovery".
Thanks.
hi how can i upgrade MAGDLR 1.12 TO 1.13 PLEASE AND ALSO HOW CAN I FLASH NEW ROM BECAUSE I DONT HAVE INSTALL IT CLOCKWORK THANKS
enter bootloader
usb
flash magldr 1.13
restart
enter magldr
5 usb flasher
flash cwm
restart
enter magldr
8 ad recovery - starts cwm
install zip from sdcard
choose zip from sdcard
restart
done
Ok thanks so much ,,but also i cant install the drivers to flash 1.13 how can i do it i need to download activesync /
YES.............download windows mobile and it'll download the drivers for u
I have Magldr 1.13 installed on my phone for a previous Froy ROM.
I want to install the NexusHD2-Gingerbread V3.2a ROM .
I followed the instructions outlined here:
Installation Guide for MAGLDR 1.13:
Flash MAGLDR
Download MAGLDR 1.13 (606 KB)
Enter SPL by holding VOL DOWN key while booting the phone. (Make sure you have HSPL.)
Run ROMUpdateUtility.exe to flash MAGLDR 1.13 (magldr.nbh).
Flash ClockworkMod Recovery
Download MAGLDR_CWM_Recovery_v3.2.0.0_for_NexusHD2_135M.zip (5.0 MB)
Enter MAGLDR 1.13 by holding power key while booting the phone, and then select "USB Flasher" via "VolUp" and "VolDown". Confirm key is green "Call" button.
Run DAF.exe to flash ClockworkMod Recovery 3.2.0.0 (recovery_3.2.0.0_leo.img).
Flash Android ROM
Enter ClockworkMod Recovery when you're on MAGLDR 1.13 (hold "Power" button during boot) and select "AD Recovery" or "Boot AD SD" (if ever copied CWM's initrd.gz and zImage to SD).
Flash NexusHD2-Gingerbread_V3.2a_NAND_(Android-2.3.7).zip (83.58 MB)
Click to expand...
Click to collapse
I got through 1 and 2. However, I am stuck at 3 - Flash android rom.
All I have is the Magldr 1.13 screen when I boot to it.
If I select "Ad Recovery", I get "No boot sources" error message
If I select "Boot AD NAND" I get "No boot sources" error message as well.
What can I do to fix it?
1. HSPL 2.08
2. MAGLDR111。
please check above two your aleady finsihed or not .and which version hd2 do using
Try to reflash CWM recovery - your installation wasn't successful due to getting "no source" in AD recovery.
Yes i thing this part is not good :
"Enter MAGLDR 1.13 by holding power key while booting the phone, and then select "USB Flasher" via "VolUp" and "VolDown". Confirm key is green "Call" button.
Run DAF.exe to flash ClockworkMod Recovery 3.2.0.0 (recovery_3.2.0.0_leo.img)"
yes if you have no boot source you have not installed cwm....
plug the phone on the pc on usb flasher and run the cwm's daf.exe...
[SOLVED]
Dear XDA Members,
i did read up already the board to look for a solution for my issue, and did read as well the noob (which i am) instructions but couldnt find a solution to my help.
I tried to install the "NexusHD2-ICS-CM9-HWA_V2.5.zip" image and now i am stuck at the boot animation (the one with the flakes) after restarting.
Here is what i did:
1.installed Mgldr 1.13
2. Clockworx Mod Recovery
3. Recovery_400M
4. Boot up => Choose AD Recovery => install zip from SD Card => Choose the zip file and install
5. Reboot
6. Tahts where i am now . The phone boots up HTC logo appears and the bootup animation with the flakes or how ot call them appears. And thats where its stuck. looping at that stage.
Edit: I did use HD2Toolkit to repartition to a system partition of 250 MB and cache size 45 MB. and Radio-Leo-2.15.50.14
SOLUTION:
Somehow the NAND zip file was broken. I downloaded again, did repeat the same procedure for installation and everything worked after rebooting
Grumpy
Grumpybumpy said:
[SOLVED]
Dear XDA Members,
i did read up already the board to look for a solution for my issue, and did read as well the noob (which i am) instructions but couldnt find a solution to my help.
I tried to install the "NexusHD2-ICS-CM9-HWA_V2.5.zip" image and now i am stuck at the boot animation (the one with the flakes) after restarting.
Here is what i did:
1.installed Mgldr 1.13
2. Clockworx Mod Recovery
3. Recovery_400M
4. Boot up => Choose AD Recovery => install zip from SD Card => Choose the zip file and install
5. Reboot
6. Tahts where i am now . The phone boots up HTC logo appears and the bootup animation with the flakes or how ot call them appears. And thats where its stuck. looping at that stage.
Edit: I did use HD2Toolkit to repartition to a system partition of 250 MB and cache size 45 MB. and Radio-Leo-2.15.50.14
SOLUTION:
Somehow the NAND zip file was broken. I downloaded again, did repeat the same procedure for installation and everything worked after rebooting
Grumpy
Click to expand...
Click to collapse
How did you determine that you needed 250 mb system partition and 45 cache? Just wondering. It might fix my stability issues that I have with my hd2 with this build.